configure 2.5G PHY LEDs to:
2500/1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX
which is similar to other 1G PHY LEDs, which are:
1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX
Fixes: 6cc14bf66a ("filogic: support Telenor branded ZyXEL EX5700")
Signed-off-by: Yan Cangang <nalanzeyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16082
(cherry picked from commit 3de653a0af)
Link: https://github.com/openwrt/openwrt/pull/16390
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ubiquiti has a set of UniFi 802.11ax (Wi-Fi 6) AP devices. All models
include "U6" in their names and also have code names with no special
characters (including spaces).
Examples:
1. U6 Lite (codename U6-Lite)
2. U6 Long-Range (codename U6-LR)
3. U6+ (codename U6-PLUS)
4. U6 Pro (codename U6-Pro)
5. U6 Mesh (codename U6-Mesh)
6. U6 Mesh Pro (codename U6-Mesh-Pro)
7. U6 Enterprise (codename U6-Enterprise)
Use proper full names for those devices. Names in OpenWrt/DTS code may
need updating too but it can be handled later.
Cc: Elbert Mai <code@elbertmai.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Henrik Riomar <henrik.riomar@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 74879140a1)
Sometimes the mmc deivce may come up later than kernel attempts to
mount rootfs, resulting kernel panic. Enable rootwait to fix it.
Reported-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15077
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to RTL8221B's datasheet, the PHY requires at least 10ms
for assert and 68ms (recommended) for de-assert. So increase the
assert/de-assert time to 15ms and 68ms respectively.
Fixes: c0c3234e17 ("mediatek: add support for JDCloud RE-CP-03")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16106
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d1954aa535)
The vendor U-Boot on the Cudy M3000 and the Yuncore AX835 assign random
mac addresses on boot and set the 'local-mac-address' property which
prevents Openwrt from assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add the
property, removes the workaround from 02_network, and adds back the nvmem
definition for the M3000.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit a55ab9e134)
Hardware:
SoC: MT7981b
RAM: 256 MB
Flash: 128 MB SPI NAND
Ethernet:
1x 2.5Gbps (rtl8221b)
1x 1Gbps (integrated phy)
WiFi: 2x2 MT7981
Buttons: Reset, WPS
LED: 1x multicolor
Solder on UART:
- remove rubber ring on the bottom
- remove screws
- pull up the cylinder, maybe help by push on an ethernet socket with a screwdriver
- remove the (3) screws holding the board in the frame
- remove the board from the frame to get to the screws for the silver, flat heat shield
- remove the (3) screws holding the heat shield
- solder UART pins to the back of the board
- make sure to have the pins point out on side with the black, finned heat spread
- the markings for the pins are going to be below the silver heat shield
- Vcc is not needed
If you don't intend on using the UART outside of the installation process, you might not
want to solder:
- carefully scrape off the thin layer of epoxy on the holes (not the copper)
- place your pin header with the UART attached in the holes
- the pins, starting with the one closest to the socket:
- Vcc (not required)
- GND
- RX
- TX
- either wedge the header or hold it with your fingers so that the pins stay in contact with the board
Installation (UART):
- attach an Ethernet cable to the 1Gbps port (black) on the router
- hold the reset button while powering the router
- press CTRL-C or wait for the timeout to get to the U-Boot prompt
- prepare a TFTP server on the network to supply ..-initramfs-kernel.bin
- use 'tftpboot' in the U-Boot shell to pull the image
- boot the image using 'bootm'
- push the ..-sysupgrade to the router using your preferred method
- perform the upgrade with 'sysupgrade -n'
There is a recovery mechanism that involves fetching a file called 'recovery.bin' but that is not understood yet.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit 20e4a18feb)
The MAC address assigned to lan/wan was reversed.
Fixes: 6e51ff88b0 ("mediatek: add support for JDCloud RE-CP-03")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The WLAN + WED reset sequence relies on being able to receive interrupts from
the card, in order to synchronize individual steps with the firmware.
When WED is stopped, leave interrupts running and rely on the driver turning
off unwanted ones.
WED DMA also needs to be disabled before resetting.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 2c5b3bee38)
In preparation to update mtk_eth_soc move accepted patches from mediatek
target to backport folder, so other patches on top can be applied more
easily.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 8730f9e536)
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- MT7531 switch
- 512MB RAM
- 128MB NAND flash with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718
- 3 buttons (WPS, reset, LED on/off)
- 1 1Gbit WAN port
- 4 1Gbit LAN ports
Disassembly:
- There are four screws at the bottom: 2 under the rubber feets, 2 under the label.
- After removing the screws, the white plastic part can be shifted out of the blue part.
- Be careful because the antennas are mounted on the side and the top of the white part.
Serial Interface
- The serial interface can be connected to the 4 pin holes on the side of the board.
- Pins (from front to rear):
- 3.3V
- RX
- TX
- GND
- Settings: 115200, 8N1
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- The recovery web interface always flashes to the currently active partition.
- If OpenWrt is flahsed to the second partition, it will not boot.
- Ensure that you have an OEM image available (encrypted and decrypted version). Decryption is described in the end.
- Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
- Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-recovery.bin
- The recovery web interface always reports successful flashing, even if it fails
- After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
- If OpenWrt was flashed to the first partition, OpenWrt will boot (The status LED will start blinking white and stay white in the end). In this case you're done and can use OpenWrt.
- If OpenWrt was flashed to the second partition, OpenWrt won't boot (The status LED will stay red forever). In this case, the following steps are reuqired:
- Start the web recovery interface again and flash the **decrypted OEM image**. This will be flashed to the second partition as well. The OEM firmware web interface is afterwards accessible via http://192.168.200.1.
- Now flash the **encrypted OEM image** via OEM firmware web interface. In this case, the new firmware is flashed to the first partition. After flashing and the following reboot, the OEM firmware web interface should still be accessible via http://192.168.200.1.
- Start the web recovery interface again and flash the OpenWrt recovery image. Now it will be flashed to the first partition, OpenWrt will boot correctly afterwards and is accessible via 192.168.1.1.
Flashing via U-Boot:
- Open the case, connect to the UART console
- Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-initramfs-kernel.bin.
- Power on the device and select "7. Load image" in the U-Boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.200.2, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util M30 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware M30A1_FW101B05: ./m32-firmware-util M30 --DecryptFactoryImage M30A1_FW101B05\(0725091522\).bin M30A1_FW101B05\(0725091522\)_decrypted.bin
Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.
Controlling the LEDs:
- The LEDs are controlled by a chip called "GCA230718" which is connected to the main CPU via I2C (address 0x40)
- I didn't find any documentation or driver for it, so the information below is purely based on my investigations
- If there is already I driver for it, please tell me. Maybe I didn't search enough
- I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
- The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
- The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
- Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
- Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
- A reset command (0x81 0xE4) written to register 0x00
- A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
- The reset command is always the same
- In the control command
- byte 0 is always the same
- byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
- byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
- byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
- byte 7 defines the toggling frequency (if toggling enabled)
- byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
- byte 12 is constant 0x87
Comparison to M32/R32:
- The algorithms for decrypting the OEM firmware are the same for M30/M32/R32, only the keys differ
- The keys are available in the GPL sources for the M32
- The M32/R32 contained raw data in the firmware images (kernel, rootfs), the R30 uses a sysupgrade tar instead
- Creation of the recovery image is quite similar, only the header start string changes. So mostly takeover from M32/R32 for that.
- Turned out that the bytes at offset 0x0E and 0x0F in the recovery image header are the checksum over the data area
- This checksum was not checked in the recovery web interface of M32/R32 devices, but is now active in R30
- I adapted the recovery image creation to also calculate the checksum over the data area
- The recovery image header for M30 contains addresses which don't match the memory layout in the DTS. The same addresses are also present in the OEM images
- The recovery web interface either calculates the correct addresses from it or has it's own logic to determine where which information must be written
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(cherry picked from commit 29cca6cfee)
The recovery image is reqired for D-Link M30 as well. So I moved it to include/image-commands.mk to be able to use it for MT7622 and filogic devices.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(cherry picked from commit 0e2b7e3bd6)
Rename network devices to their label set in DT without invocation of
a sub-shell.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 983222605c)
Implement the functionality of
target/linux/ramips/patches-5.15/700-net-ethernet-mediatek-support-net-labels.patch
in userspace, since the driver patch has been rejected as a generic solution:
https://github.com/openwrt/openwrt/pull/11435
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 1dd1ac2c35)
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: W632GU6NB DDR3 256MB
Ethernet: 1x 2.5G + 4x 1G
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
1. Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
2. Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-preloader.bin spi0.0"
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
3. Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
4. Download initramfs image, reboot router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Note:
1. Back up all mtd partitions before flashing.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 4ae474afbd)
R32 is like the M32 part of the EAGLE PRO AI series from D-Link.
Specification:
- MT7622BV SoC with 2.4GHz wifi
- MT7975AN + MT7915AN for 5GHz
- MT7531BE Switch
- 512MB RAM
- 128 MB flash
- 2 LEDs (Status and Internet, both can be either orange or white)
- 2 buttons (WPS and Reset)
Compared to M32, the R32 has the following differences:
- 4 LAN ports instead of 2
- The recory image starts with DLK6E6015001 instaed of DLK6E6010001
- Individual LEDs for power and internet
- MAC address is stored at another offset in the ODM partition
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin
Flashing via uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
- Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin
Revert back to stock using uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides the previously created backup of the Kernel1 partition.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to FLASH will start. After a few seconds the stock firmware should start again
There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP.
It can be used if no backup of the Kernel1 partition is reuqired.
Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment.
The support for the M32/R32 already includes support for flashing from the OEM web interface:
- The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line
- The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface
- OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap)
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(cherry picked from commit fdb87a91b4)
Link: https://github.com/openwrt/openwrt/pull/15776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.
Oem firmware is a custom openwrt 21.02 snapshot version.
We can gain access via ssh once we remove the root password.
Hardware specification:
SoC: MediaTek MT7981A 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976D
LEDS: 1x (Red, Blue and Green)
Button: Reset
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC GND TX RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
and download the
configuration(http://apipaddress/computer/config.html).
2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
Enter 'fakeroot' command then decompress the configuration:
tar -zxf backup.tar.gz
3. Edit 'etc/shadow', update (remove) root password:
With password =
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
to
Without password =
'root::0:99999:7:::'
'root::0:99999:7:::'
4. Repack 'etc' directory back to a new backup file:
tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
Exit fakeroot - 'exit'
6. Upload new configuration via web interface, now you
can SSH with the following:
'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.
Backup the mtd partitions
- https://openwrt.org/docs/guide-user/installation/generic.backup
7. Copy openwrt factory firmware to the tmp folder to install via ssh:
'scp -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa \
*-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
root@192.168.10.1:/tmp/'
'sysupgrade -n -F \
/tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'
8. Once led has stopped flashing - Connect via ssh with the
default openwrt ip address - 'ssh root@192.168.1.1'
9. SSH copy the openwrt sysupgrade firmware and upgrade
as per the default instructions.
Signed-off-by: David Bentham <db260179@gmail.com>
(cherry picked from commit d8f4453bf2)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 16MB NOR
RAM: 256MB
Ethernet: 2x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
Power: DC 12V 1A, PoE 802.3af 48V
Flash instructions:
Option #1 - SSH
I was able to SSH into the stock firmware of my device.
1. Attach the router to the network
2. Use scp (-O) to copy the sysupgrade image
3. Connect using SSH and run `sysupgrade -n`
Option #2 - U-Boot
One way to use the bootloader for flashing is using TFTP:
1. Connect to the router using an ethernet cable
2 Spin up a TFTP server serving the sysupgrade file
3. Open the case and attach a UART
4. Attach power to the router and interrupt the countdown by pressing
any key
5. Select option #2 (Upgrade firmware)
6. Enter IP address information and image name
7. Wait patiently
Co-Authored-By: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit b4086f44cd)
The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s
Wi-Fi 6 residential gateway, access point and mesh router products.
All of them come with an eMMC to boot from, are powered via USB-C and
got a USB 3.0 type-A port. All of them got a Dialog (Renesas) DA14531
Bluetooth module connected via UART. If the device was previously
running stock firmware, the BT chip's internal flash has been loaded
with firmware and it can be attached using hciattach when using
OpenWrt.
SOC: MediaTek MT7986A
RAM: 2 GiB DDR4
eMMC: 8 GiB
Bluetooth: BLE5 (DA14531)
Serial: 3.3V level, 115200 8n1 on 4-pin connector
* SDG-8612 - Dual-band RJ-45 gateway
2x 2.5G MaxLinear PHY for WAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8614 - Dual-band SFP gateway
1x SFP cage with up to 2.5G speed
1x 2.5G MaxLinear PHY for LAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8622 - Tri-band mesh router
2x 2.5G MaxLinear PHY
The MT7986 2G and 5G are used as 2G and 5G high band.
There’s a MT7915 PCIe card for 5G low band.
* SDG-8632 - Tri-band mesh router with 6 GHz
2x 2.5G MaxLinear PHY
The MT7986 serves the 2G and 6G bands.
There’s a MT7915 PCIe card for 5G.
Installation via U-Boot serial console:
0. setup TFTP server with IP 192.168.1.10/24, place initramfs image
renamed to openwrt.XXX where XXX is the internal product number:
SDG-8612: XXX = 412
SDG-8614: XXX = 414
SDG-8622: XXX = 422
SDG-8632: XXX = 432
1. connect to the serial console and power on the device.
Interrupt the bootloader by pressing 'st'
2. setenv boot_mode openwrt ; saveenv
3. run boot1
Load firmware via TFTP and write to flash
4. run boot2
Now OpenWrt initramfs should boot
5. upload sysupgrade.bin via scp to /tmp
6. sysupgrade
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 3aa686f8d4)
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.
Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi
Buttons:
Reset-Mesh
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Signed-off-by: Ian Oderon <ianoderon@gmail.com>
(cherry picked from commit 4300bc6688)
Include XHCI USB drivers on the ZBT-Z8102AX router, the drivers are
required to be able to use the USB-connected M.2 slots for 4G/5G modems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 507ad4f078)
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: internal test points, 115200 8n1
- Power: 5 VDC, 3 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 82:af:ca:xx:xx:x0 | |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware to make installation easier, and so I recommend checking the Wiki for this device if there is a more convenient solution than the one below.
To install using TFTP:
1. Connect to UART.
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an OpenWrt initramfs-kernel.bin firmware file.
5. Run these steps in u-boot using the name of your file.
setenv bootfile initramfs-kernel.bin
tftpboot
bootm
6. If you can reach LuCI or SSH now, just use the sysupgrade image with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
(cherry picked from commit 63b8d98dd0)
The NMBM-Enabled layout did not use fit image,
it just need default process. So it was been removed in platform.sh.
It will fix sysupgrade error for xiaomi,mi-router-wr30u-112m-nmbm.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
(cherry picked from commit 02214ab8dc)
This reverts commit dcdcfc1511.
This is a firmware for third-party u-boot mod, which should not
be carried here by us.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 1b7e62b20b)
The patch "710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch"
makes use of "syscon_regmap_lookup_by_phandle" which requires that
"syscon" be in the compatible list.
Without this patch, PCIe probe will fail with the following error:
[ 1.287467] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
[ 1.294019] mtk-pcie 1a143000.pcie: Parsing ranges property...
[ 1.299901] mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000
[ 1.307954] mtk-pcie 1a143000.pcie: missing hifsys node
[ 1.313185] mtk-pcie: probe of 1a143000.pcie failed with error -22
Fixes: 01c58a0d2a ("kernel: bump 5.15 to 5.15.158")
Signed-off-by: Rany Hany <rany_hany@riseup.net>
(cherry picked from commit 8607372b41)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 8GB eMMC or 128 MB SPI-NAND
RAM: 256MB
Ethernet: 5x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
USB: M.2(B-key) for 4G/5G Module
Power: DC 12V 1A
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC RX TX GND | <= |
| ----------------- |
--------------------------
The U-boot menu will automatically appear at startup, and then select
the required options through UP/DOWN Key.
NAND Flash and eMMC Flash instructions:
1. Set your computers IP adress to 192.168.1.2.
2. Run a TFTP server providing the sysupgrade.bin image.
3. Power on the router, into the U-Boot menu.
4. Select "2. Upgrade firmware"
5. Update sysupgrade.bin file name, input server IP and input device
IP (if they deviate from the defaults)
6. Wait for automatic startup after burning
Signed-off-by: Allen Zhao <allenzhao@unielecinc.com>
(cherry picked from commit 640b0b79ff)
Set 12mA driving strength for SPI-NAND pins like the stock firmware's
bootloader does as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 45a2109353)
Some Aquantia PHYs (e.g. AQR113C) require firmware to be uploaded by
host system. With built-in drivers this doesn't work in OpenWrt /
embeddded as filesystem isn't available during PHY probe. That results
in delays like:
[ 1.588068] Aquantia AQR113C mdio-bus:00: Falling back to sysfs fallback for: Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld
[ 64.526387] Aquantia AQR113C mdio-bus:00: failed to find FW file Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld (-110)
Switch to module to postpone PHY probe to init state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 3bd79e6136)
Router Asus TUF AX6000 have second MaxLinear GPY211 PHY controller for 2.5Gb LAN port.
The 5'th LAN port have inverted status of the LED.
Based on the commit from main branch 90fbec8 we could set proper status of the LED.
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
(cherry picked from commit b22539b5fe)
Signed-off-by: Tom Herbers <mail@tomherbers.de>
Add downstream DT property to setup the PHY LEDs of the MaxLinear
GPY211 PHY in such way that the VDD of the LED is driven by the SoC
pin rather than the GND (which is the default).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 90fbec89be)
[removed patches for kernel 6.1]
Signed-off-by: Tom Herbers <mail@tomherbers.de>
Fixes: d522ccecb2 ("filogic: add support for ASUS TUF AX6000")
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
(cherry picked from commit 0c3f4bd85e)
Signed-off-by: Tom Herbers <mail@tomherbers.de>
MT7981B /256MB /16MB SPI (XM25QH128C)
AX 2.4Ghz
AX 5Ghz 160Mhz wide
1Gbit LAN
OEM:
root@RE3000:~# ifconfig |grep HWaddr
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 (label)
br-wan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra2 Link encap:Ethernet HWaddr 82:XX:XX:28:XX:X0
rax0 Link encap:Ethernet HWaddr 82:XX:XX:38:XX:X0
rax2 Link encap:Ethernet HWaddr 82:XX:XX:58:XX:X0
OpenWrt
root@OpenWrt:/# ifconfig |grep HW
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy0-ap0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy1-ap0 Link encap:Ethernet HWaddr 82:XX:XX:08:XX:X1
tftp Installation via u-boot:
Connect TTL3.3V converter
connector is under the radiator Set speed 115200 8 N 1
Interrupt boot process by holding down-arrow key during boot then
>> 6. Load image
>> 0 - TFTP client (Default)
enter IP adresses and initramfs-kernel.bin
write to flash via sysupgrade or gui
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
(cherry picked from commit e8f7597317)
* fix switch ports with modes other than 1000M/Full
* set 32-bit dma_coherent_mask to get PPE to work with 4 GiB of RAM
* sync driver for built-in 1GE PHY with MediaTek SDK sources
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4ae2f43b3a)
