In case of the block device still being in use, re-reading the
partition table fails. In that case, abort sysupgrade to avoid
corrupting the just-written image because of wrong offsets caused
by failure to re-read the partition table.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds support for the Netgear Nighthawk Pro Gaming XR500.
It is the successor to the Netgear Nighthawk R7800 and shares almost
identical hardware to that device.
The stock firmware is a heavily modified version of OpenWRT.
Specifications:
SoC: Qualcomm Atheros IPQ8065
RAM: 512 MB
Storage: 256 MiB NAND Flash
Wireless: 2x Qualcomm Atheros QCA9984
Ethernet: 2x 1000/100/10 dedicated interfaces
Switch: 5x 1000/100/10 external ports
USB: 2x 3.0 ports
More information:
Manufacturer page: https://www.netgear.com/gaming/xr500/
Almost identical to Netgear R7800
Differences (r7800 > xr500):
Flash: 128MiB > 256MiB
Removed esata
swapped leds:
usb1 (gpio 7 > 8)
usb2 (gpio 8 > 26)
guest/esata (gpio 26 > 7)
MAC addresses:
On the OEM firmware, the mac addresses are:
WAN: *:50 art 0x6
LAN: *:4f art 0x0 (label)
2G: *:4f art 0x0
5G: *:51 art 0xc
Installation:
Install via Web Interface (preferred):
Utilize openwrt-ipq806x-netgear_xr500-squashfs-factory.img
Install via TFTP recovery:
1.Turn off the power, push and hold the reset button (in a hole on
backside) with a pin
2.Turn on the power and wait till power led starts flashing white
(after it first flashes orange for a while)
3.Release the reset button and tftp the factory img in binary mode.
The power led will stop flashing if you succeeded in transferring
the image, and the router reboots rather quickly with the new
firmware.
4.Try to ping the router (ping 192.168.1.1). If does not respond,
then tftp will not work either.
Uploading the firmware image with a TFTP client
$ tftp 192.168.1.1
bin
put openwrt-ipq806x-netgear_xr500-squashfs-factory.img
Note:
The end of the last partition is at 0xee00000. This was chosen
by the initial author, but nobody was able to tell why this
particular arbitrary size was chosen. Since it's not leaving
too much empty space and it's the only issue left, let's just
keep it for now.
Based on work by Adam Hnat <adamhnat@gmail.com>
ref: https://github.com/openwrt/openwrt/pull/3215
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
[squash commits, move common LEDs to DTSI, remove SPDX on old
files, minor whitespace cleanup, commit message facelift,
add MAC address overview, add Notes, fix MAC addresses,
use generic name for partition nodes in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Allow RAM size to be passed thru U-Boot. There are 128MB and 64MB
versions of Minew G1-C. This is also in line with the behaviour of
most other RAMIPS boards.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Compile tested and run tested on Pine64+.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Add support for SAM9X60-EK board.
Hardware:
- SoC: SAM9X60
- RAM: Winbond W972GG6KB-25 (2Gbit DDR2)
- NAND Flash: Micron MT29F4G08ABAEA
- QSPI Flash: Microchip SST26VF064B
- EEPROM: Microchip 24AA02E48
- SDMMC: One standard 4-bit SD card interface
- USB: two stacked Type-A connectors with power switches, one micro-B
USB device
- CAN: 2 interfaces (Microchip MCP2542)
- Ethernet: one 10/100Mbps
- WiFi/BT: one optional WiFi/Bluetooth interface
- Audio: one ClassD port
- Display: one 24-bit LCD interface
- Camera: one 12-bit image sensor interface
- IO: one IO expander (Microchip MCP23008)
- Debug ports: one J-Link-OB + CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: 4 push button switches
- Expansion: one PIO connector, one mikrobus connector
- Power management: two power regulators, two power consumption measurement
devices
Flashing:
- follow the procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sam9x60EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D27 WLSOM1-EK board.
Hardware:
- SIP: SAMA5D27C-LD2G-CU including SAMA5D27 MPU and 2Gbit LPDDR2-SDRAM
- MMC: one standard SD card interface
- Flash: 64 Mb serial quad I/O flash memory (SST26VF064BEUIT-104I/MF)
with embedded EUI-48 and EUI-64 MAC addresses
- USB: one USB device, one USB host one HSIC interface
- Ethernet: 1x10/100Mbps port
- WiFi/BT: IEEE 802.11 b/g/n Wi-Fi plus Bluetooth (Wi-Fi/BT) module
(ATWILC3000-MR110UA)
- Crypto: one ATECC608B-TNGTLS secure element
- Video: one LCD RGB 18-bit interface, one ISC 12-bit camera interface
- Debug port: one JTAG interface, one UART interface, one WILC UART
interface
- Leds: one RGB LED
- Buttons: start, reset, wakeup, user buttons
- Expansion: one tamper connector, one mikrobus interface, 2 XPRO PTC
connector
- Power managament: PMIC (MCP16502)
Flashing:
- follow procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d27WLSom1EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D2 ICP board.
Hardware:
- SoC: SAMA5D27
- RAM: 512 MB DDR3L
- MMC: One stanard SD card interface
- USB: One USB host switch 4 ports with power switch,
One USB device type Micro-AB
- CAN: 2 interfaces
- Ethernet: One Gigabit Ethernet PHY through HSIC,
One ETH switchport,
One EtherCAT interface
- WiFi/BT: Footprint for IEEE 802.11 b/g/n Wi-Fi plus
Bluetooth module (Wi-Fi/BT), suitable for
Microchip WILC3000-MR110CA or WILC3000-MR110UA
- Debug port: One J-Link-OB/J-Link-CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: reset, wakeup, 2 user buttons
- Expansion: one PIOBU/PIO connector, 3 mikrobus sockets
- Power mangament: PMIC (MCP16502), one power consumption device
(PAC1934)
Not working in Linux:
- EtherCAT interface: there is no Linux support integrated
- PAC1934: driver available at [1] but not integrated in Linux
Flashing:
- follow the procedure at [2]
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/pac193x_linux_driver.zip
[2] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d2IcpMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Bump at91 targets to kernel v5.10. With this patches and files for
wb45n and wb50n were removed as they are now included in upstream
kernel. Along with:
- this the kernel config for sama5d2 and sam9x targets has been
refreshed (with make kernel_menuconfig + save);
- CONFIG_ARCH_AT91 and specific sam9x SoCs (AT91RM9200, AT91SAM9,
SAM9X60) has been enabled such that sam9x SoCs to be able to boot.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Enable the sun8i-thermal driver to allow reading the
temperature of the SoC.
As suggested by mans0n, disable this driver in the
a8 subtarget because it does not support yet.
Tested on NanoPi R1S H5.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Tidy qca8k_setup for loops relating to port handling. No functional
changes.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Add cpu_port_index fix to apply settings to correct CPU port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Backport Ansuel Smith's various qca8k feature additions:
- mac-power-sel support
- SGMII PLL explicit enable
- tx/rx clock phase to falling edge
- power-on-sel and LED open drain mode
- cpu port 6
- qca8328 support
- sgmii internal delay
- move port config to dedicated struct
- convert to yaml schema
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Backport workaround for QCA8327 PHY resume, which does not properly support
genphy_suspend/resume. Also add DAC amplitude fix for the QCA8327 PHY,
set port to preferred master and add proper names to debug regs.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This commit add accepted upstream patches that improve & tidy qca83xx support.
1 - Split qca8327 to A & B variants, identifiable by phy_id
2 - Add suspend/resume support to qca8xx phys
3 - Tidy spacing and phy naming.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Add support for qca8327 internal phy needed for correct init of the
switch port. It does use the same qca8337 function and reg just with a
different id.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Backport fixes including:
net: dsa: qca8k: fix missing unlock on error in qca8k_vlan_(add|del)
net: dsa: qca8k: check return value of read functions correctly
net: dsa: qca8k: add missing check return value in qca8k_phylink_mac_config()
net: dsa: qca8k: fix an endian bug in qca8k_get_ethtool_stats()
net: dsa: qca8k: check the correct variable in qca8k_set_mac_eee()
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This is a backport of Ansuel Smith's "Multiple improvement to qca8k stability"
series. The QCA8337 switch is available on multiple platforms including
ipq806x, ath79 and bcm53xx.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Rosen reported strange dtc warnings that had their origin in
an upstream patch to 5.8-rc1. Upon further digging this
revealed an ongoing thread [0] discussing the topic:
> [...]I don't think we need a bunch of warning fix patches to add
> these everywhere. Also, the need for #address-cells pretty much makes
> no sense on any modern system. It is a relic from days when the bus
> (address) topology and interrupt topology were related.
and later on:
> So really, we only need to be checking for #address-cells in nodes
> with interrupt-map.
This patch backports just the patch which removed the warning message
(this is from the upstream dtc project [1] - but not the kernel).
the patch does not add the checking of the #address-cells in nodes
with interrupt-map.
[0] <https://lore.kernel.org/linux-devicetree/91e3405245c89f134676449cf3822285798d2ed2.1612189652.git.michal.simek@xilinx.com/>
[1] <https://git.kernel.org/pub/scm/utils/dtc/dtc.git/commit/?id=d8d1a9a77863a8c7031ae82a1d461aa78eb72a7b>
Link: <https://github.com/openwrt/openwrt/pull/4685>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ag71xx_probe is registering ag71xx_interrupt as handler for the gmac0/gmac1
interrupts. The handler is trying to use napi_schedule to handle the
processing of packets. But the netif_napi_add for this device is
called a lot later in ag71xx_probe.
It can therefore happen that a still running gmac0/gmac1 is triggering the
interrupt handler with a bit from AG71XX_INT_POLL set in
AG71XX_REG_INT_STATUS. The handler will then call napi_schedule and the
napi code will crash the system because the ag->napi is not yet
initialized:
libphy: Fixed MDIO Bus: probed
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 00000000, ra == 81373408
Oops[#1]:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.152 #0
$ 0 : 00000000 00000001 00000000 8280bf28
$ 4 : 82a98cb0 00000000 81620000 00200140
$ 8 : 00000000 00000000 74657272 7570743a
$12 : 0000005b 8280bdb9 ffffffff ffffffff
$16 : 00000001 82a98cb0 00000000 8280bf27
$20 : 8280bf28 81620000 ffff8b00 8280bf30
$24 : 00000000 8125af9c
$28 : 82828000 8280bed8 81610000 81373408
Hi : 00005fff
Lo : 2e48f657
epc : 00000000 0x0
ra : 81373408 __napi_poll+0x3c/0x11c
Status: 1100dc03 KERNEL EXL IE
Cause : 00800008 (ExcCode 02)
BadVA : 00000000
PrId : 00019750 (MIPS 74Kc)
Modules linked in:
Process swapper (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000)
Stack : ffff8afb ffff8afa 81620000 00200140 00000000 82a98cb0 00000008 0000012c
81625620 81373684 ffffffff ffffffff ffffffef 00000008 816153d8 81620000
815b0d60 815bbd54 00000000 81753700 8280bf28 8280bf28 8280bf30 8280bf30
81753748 00000008 00000003 00000004 0000000c 00000100 3fffffff 8175373c
816059f0 814ddb48 00000001 8160ab30 81615488 810618bc 00000006 00000000
...
Call Trace:
[<81373684>] net_rx_action+0xfc/0x26c
[<814ddb48>] __do_softirq+0x118/0x2ec
[<810618bc>] handle_percpu_irq+0x50/0x80
[<8125ab8c>] plat_irq_dispatch+0x94/0xc8
[<81004e98>] handle_int+0x138/0x144
Code: (Bad address in epc)
---[ end trace a60d797432b656b2 ]---
The gmcc0/gmac1 must be brought in a state in which it doesn't signal a
AG71XX_INT_POLL related status bits as interrupt before registering the
interrupt handler. ag71xx_hw_start will take care of re-initializing the
AG71XX_REG_INT_ENABLE.
Fixes: f529a37420 ("surprise :p")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This allows to specify and control switch LEDs on devices using mt7530
(typically mediatek and ramips targets).
Normally these LED GPIOs are 0, 3, 6, 9, and 12. wan/lan assignment is
per device. GPIO 9 is normally inverted. so GPIO_ACTIVE_HIGH instead of
GPIO_ACTIVE_LOW.
Tested on Linksys E7350.
Refreshed all patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This fixes a kernel build problem.
The removed parts of the patch are already applied upstream.
Fixes: 9ad3ef27b9 ("kernel: bump 5.4 to 5.4.153")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This should have been included in the previous patch that
resized the kernel partition to fit bigger kernels.
Fixes: 7a6a349445 ("apm821xx: WNDAP620 + WNDAP660: reorganize partitions for 5.10")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates all current APM82181 devices over to that
"new LED naming scheme". This includes many updates to the
device-tree:
- dropped the deprecated, but beloved "label" property.
- rename all DT leds node names to led-#.
- add function and color properties.
- utilized panic-indicator property.
- dropped led- aliases (see below).
migration scripts for all devices are included.
For more information. See:
<https://www.kernel.org/doc/html/latest/leds/leds-class.html>
For the future: It looks like the color+function properties
won over the dt-alias / label. This will need to be wired up
into openwrt eventually. For APM821xx the situation is that
all devices have a dedicated power and fault indicator.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Back in the AR71XX days, the lzma-loader code could be customized
based on the $BOARD variable. These would be passed as a
compile-time -DCONFIG_BOARD_$DEVICE_MODEL flag to the compiler.
Hence, the lzma-loader would be able to include device-specific
fixups.
Note: There's still a fixup for the TpLink TL-WR1043ND V1 found
in the lzma-loader's board.c code. But since the days of AR71XX
I couldn't find a forum post or bug reported. So, I left it
as is to not break anything by enabling it.
=> If you have a TL-WR1043ND V1 and you have problem with
the ethernet: let me know. Because otherwise, the fixup
might simply no longer needed with ath79 and it can be removed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The MX60's kernel is limited to 0x3EFC00 by the values in
mkmerakifw.c. Since the initramfs method of loading the
kernel seems to be working, this patch does away with the
use of the mkmerakifw tool for the MX60(W).
But this will go along with a change in u-boot as well.
So before you upgrade, please attach the serial cable and
perform:
| setenv owrt510_boot run meraki_ubi owrt_bootargs\; run owrt_load1 owrt_bootkernel\; run owrt_load2 owrt_bootkernel
| setenv bootcmd run owrt510_boot
| saveenv
Note: You won't be able to use older OpenWrt releases without
switching the bootcmd back to owrt_boot!
Note2: We are no longer compatible with older OpenWrt MX60 installs.
the legacy BOARD_NAME and SUPPORTED_DEVICES can be dropped. This is
because upgrades from older images are not possible without uboot env
changes anymore. Also the bogus BLOCKSIZE value
(which was set to 63k back then, in order to get the kernel properly
aligned after the fdt + meraki header) can be set to the NANDs real
value. The FDT size (which was needed for alignment) can now be
slimmed down as well.
Co-developed-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Takimata reported on the OpenWrt forum in thread [0], that his
MyBook Live Duo wasn't booting OpenWrt 21.02 after upgrading
from the previous OpenWrt 19.07.
The last logged entries on his console
|[ 0.531599] sata1-regulator GPIO handle specifies active low - ignored
|[ 0.538391] sata0-regulator GPIO handle specifies active low - ignored
|[ 0.759791] ata2: SATA link down (SStatus 0 SControl 300)
|[ 0.765251] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
|[ 5.909555] ata1.00: qc timeout (cmd 0xec)
|[ 5.913656] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
|[ 6.231757] ata1: SATA link down (SStatus 0 SControl 300)
This extract clearly showed that the HDD on which OpenWrt is installed,
simply disappeared after the SATA power regulators had been initialized.
The reason why this worked with OpenWrt 19.07 was because the kernel
config symbol CONFIG_REGULATOR=y was not set in the target's config-4.14.
(This shows that the MBL Single does differ from the DUO in that
it does not have programmable power regulators for the HDDs.)
[0] <https://forum.openwrt.org/t/21-02-0-and-snapshot-fail-to-boot-on-my-book-live-duo/106585>
Reported-by: Takimata (forum)
Tested-by: Takimata (forum)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch removes CONFIG_MTD_SPI_NOR_USE_4K_SECTORS from the default
symbols for the ath79/mikrotik target.
MikroTik devices hold some of their user-configurable settings in the
soft_config partition, which is typically sized 4 KiB, of the SPI NOR
flash memory. Previously, in the ar71xx target, it was possible to use
64 KiB erase sectors but also smaller 4 KiB ones when needed. This is
no longer the case in ath79 with newer kernels so, to be able to write
to these 4 KiB small partitions without erasing 60 KiB around, the
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS symbol was added to the defaults.
However, this ended up making sysupgrade images which were built with
64 KiB size blocks not to keep settings (e.g., the files under
/etc/config/) over the flashing process.
Using 4 KiB erase sector size on the sysupgrade images (by setting
BLOCKSIZE = 4k) allows keeping settings over a flashing process, but
renders the process terribly slow, possibly causing a user to
mistakenly force a manual device reboot while the process is still on-
going. Instead, ditching the 4 KiB erase sectors for the default
64 KiB erase size provides normal SPI write speed and sysupgrade times,
at the expense of not being able to modify the soft_config partition
(which is rarely a required thing).
An OpenWrt patch for MTD_SPI_NOR_USE_4K_SECTORS_LIMIT may once have
allowed to use different per-partition erase sector sizes. Due to
changes on recent kernels it now only works on a per-device basis.
Also, partial eraseblock write can be performed in ath79 with kernels
5.4 and lower, by copying the blocks from the 64 KiB, erasing the whole
sector and restoring those blocks not meant to be modified. A kernel
bump had that patch broken for a long time, but got fixed in bf2870c.
Note: the settings in the soft_config partition can be reset to their
defaults by holding the reset button for 5 seconds (and less than 10
seconds) at device boot.
Fixes: FS#3492 (sysupgrade […] loses settings...)
Fixes: a66eee6336 (ath79: add mikrotik subtarget)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
AR9331 requires kmod-usb2-chipidea to use the USB ports. Include the
correct package so they can be used with the base image.
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport upstream SFP support for the Marvell 88E1510/2 PHY-s.
Globalscale MOCHAbin uses this PHY for the hybrid
WAN port that has 1G SFP and 1G RJ45 with PoE PD
connected to it.
This allows the SFP port to be used on it as well as
parsing the SFP module details with ethtool.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Backport upstream support for 100Base-FX, 100Base-LX, 100Base-PX and
100Base-BX10 SFP modules.
This is a prerequisite for the Globalscale MOCHAbin hybrid 1G
SFP/Copper support backporting.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Removed upstreamed:
backport-5.4/070-v5.5-MIPS-BPF-Restore-MIPS32-cBPF-JIT.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
This target has testing support for kernel 5.10 for four months now.
Time to switch the default.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Both should be supported since:
1. Adding NVMEM driver for NVRAM
2. Using NVRAM info for determining active firmware partition
Linksys EA9500 uses very similar design and works fine.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This firmware should only be used for mobile devices (e.g. laptops), where
AP mode functionality is typically not used. This firmware supports a lot
of power saving offload functionality at the expense of AP mode support.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use kernel 5.10 by default
compile-tested: all devices from target (wth ALL_KMODS)
run-tested: Digilent Zybo Z7-20
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This fixes compilation of several wireless drivers that
require support for the old wireless extension to work.
One example is kmod-hermes.
The symbols are set to "y" on generic configuration.
But they were wrongly disabled on the target-specific
configuration.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This Kernel option allows to run OpenWrt witin a `firecracker` micro VM.
Firecracker is a KVM-based tool for superfast booting VMs on x86_64 and
aarch64. It makes rootfs available to the guest as a virtio-mmio device
and passes its address via the kernel cmdline. A kernel without
CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES will not recognize the rootfs
virtio-mmio device.
Suggested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
This Kernel option allows to run OpenWrt witin a `firecracker` micro VM.
Firecracker is a KVM-based tool for superfast booting VMs on x86_64 and
aarch64. It makes rootfs available to the guest as a virtio-mmio device
and passes its address via the kernel cmdline. A kernel without
CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES will not recognize the rootfs
virtio-mmio device.
Suggested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
This reverts commit f536f5ebdd.
As Hauke commented, this causes builder failures on 5.4 kernels.
This revert includes changes to the mx100 kernel modules
dependency as well as the uci led definitions.
Tested-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In the "ipq40xx: switch to Kernel 5.10" discussion at GitHub,
Adrian noted [0] that these GL.iNet Conexa series devices,
GL-B1300 and GL-S1300 failed their image generation [1] as their gzipped
uImage kernel went above 4096k.
While notifying the vendor about this problem [2], I tested all U-Boot
releases from GL.iNet:
- they really fail to boot kernel above 4096k
- they don't support lzma: "Unimplemented compression type 3"
- but they boot zImage
Using zImage (xz compression) the kernel is 2909k which is
more than a megabyte away from the KERNEL_SIZE := 4096k limit.
The gzip compressed version would be 4116k.
[0]: https://github.com/openwrt/openwrt/pull/4620#issuecomment-932765776
[1]: commit 7b1fa276f5 ("ipq40xx: add testing support for kernel 5.10")
[2]: https://forum.gl-inet.com/t/ipq40xx-kernel-size-and-u-boot-v5-10-is-too-big-for-4-mb/17619
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
This commit will add support for the Meraki MX100 in OpenWRT.
Specs:
* CPU: Intel Xeon E3-1200 Series 1.5GHz 2C/4T
* Memory: 4GB DDR3 1600 ECC
* Storage: 1GB USB NAND, 1TB SATA HDD
* Wireless: None
* Wired: 10x 1Gb RJ45, 2x 1Gb SFP
UART:
The UART header is named CONN11 and is found in the
center of the mainboard. The pinout from Pin 1 (marked
with a black triangle) to pin 4 is below:
Pin 1: VCC
Pin 2: TX
Pin 3: RX
Pin 4: GND
Note that VCC is not required for UART on this device.
Booting:
1. Flash/burn one of the images from this repo to a
flash drive.
2. Take the top off the MX100, and unplug the SATA
cable from the HDD.
3. Hook up UART to the MX100, plug in the USB drive,
and then power up the device.
4. At the BIOS prompt, quickly press F7 and then
scroll to the Save & Exit tab.
5. Scroll down to Boot Override, and select the
UEFI entry for your jumpdrive.
Note: UEFI booting will fail if the SATA cable for
the HDD is plugged in.
The issue is explained under the Flashing instructions.
Flashing:
1. Ensure the MX100 is powered down, and not plugged
into power.
2. Take the top off the MX100, and unplug the SATA
cable from the HDD.
3. Using the Mini USB female port found by the SATA
port on the motherboard,
flash one of the images to the system. Example:
`dd if=image of=/dev/sdb conv=fdatasync` where sdb
is the USB device for the MX100's NAND.
4. Unplug the Mini USB, hook up UART to the MX100,
and then power up the device.
5. At the BIOS prompt, quickly press F7 and then
scroll to the Boot tab.
6. Change the boot order and set UEFI: USB DISK 2.0
as first, and USB DISK 2.0 as second.
Disable the other boot options.
7. Go to Save & Exit, and then select Save Changes and
Reset
Note that OpenWRT will fail to boot in UEFI mode when
the SATA hard drive is plugged in. To fix this, boot
with the SATA disk unplugged and then run the following
command:
`sed -i "s|hd0,gpt1|hd1,gpt1|g" boot/grub/grub.cfg`
Once the above is ran, OpenWRT will boot when the HDD
is plugged into SATA. The reason this happens is the
UEFI implementation for the MX100 will always set
anything on SATA to HD0 instead of the onboard USB
storage, so we have to accomidate it since OpenWRT's
GRUB does not support detecting a boot disk via UUID.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
try to reduce the kernel size by disabling and moving
options from the common kernel configuration to the
SATA target that doesn't have the constraints.
For NAND this has become necessary because as with 5.10
some devices outgrew their kernels. Though, in my tests
this didn't help much: just a smidgen over 100kib was
saved on the uncompressed kernel.
... running make kernel_oldconfig also removed some
other config symbols, mostly those that already set
from elsewhere or became obsolete in the meantime.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
disables the MX60(W) from being built by the builders for now.
But there's an effort to bring it back:
<https://github.com/openwrt/openwrt/pull/4617>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The D-Link DIR-685 has a small screen with a framebuffer
console, so if we have this, when we start, display the
banner on this framebuffer console so the user know they
are running OpenWRT as root filesystem.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Due to 5.10 increased kernel size, the current 4MiB-ish kernel
partition got too small. Luckily, netgear's uboot environment
is setup to read 0x60000 bytes from the kernel partition location.
... While at it: also do some cleanups in the DTS in there.
The original (re-)installation described in
commit d82d84694e ("apm821xx: add support for the Netgear WNDAP620 and WNDAP660")
seemed to be still working for now. What I noticed though
is that the bigger initramfs images needed to use a different
destination address (1000000) to prevent it overwriting
itself during decompression. i.e:
# tftp 1000000 openwrt-...-wndap620-initramfs-kernel.bin
# bootm
However, in case of the WNDAP620+660 the factory.img image can be
written directly to the flash through uboot.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Both NAND and SATA targets need the DMA engine in one way
or another.
Due to a kernel config refresh various existing symbols
got removed from the apm821xx main config file as well.
(That being said, they are still included because the
built-in crpyto4xx depends on these.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kernel has added the different variants of the Rock Pi 4 in commit
b5edb0467370 ("arm64: dts: rockchip: Mark rock-pi-4 as rock-pi-4a
dts"). The former Rock Pi 4 is now Rock Pi 4A.
For compatibility with kernel 5.4, this rename has been held back
so far. Having switched to kernel 5.10 now, we can finally apply
it in our tree as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Now that we have fully switched to nvmem interface we can drop
the use of mtd-mac-address patches as it's not used anymore and
the new nvmem implementation should be used for any new device.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
LED labels got reversed by accident, so fix it to the usual color:led_name format.
Fixes: 78cf3e53b1 ("mvebu: add Globalscale MOCHAbin")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Linux 5.10 has been there as testing kernel for a while now.
Do the switch and drop config and patches for Linux 5.4.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable kernel options to allow loading device tree overlay via configfs
at runtime. This is useful for devboards like the BPi-R2 and BPi-R64
which got RasbPi-compatible 40-pin GPIO header which allow all sorts
of extensions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The otto GPIO driver does not work with rtl9300 SoCs. Add
the legacy driver again and use that by default in the 9300 .dtsi
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
RTL8393 SoCs older than Revision C hang on accesses to PHYs with PHY address
larger or equal to the CPU-port (52). This will make scanning the MDIO bus
hang forever. Since the RTL8390 platform does not support more than
52 PHYs, return -EIO for phy addresses >= 52. Note that the RTL8390 family
of SoCs has a fixed mapping between port number and PHY-address.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Adds SoC specific routing offload implementations for
RTL8380/90 and RTL9300. RTL83xx supports merely nexthop
routing, RTL9300 full host and prefix routes.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Add generic support for listening to FIB and Event notifier updates and
use this information to hook into the L3 hardware capabilities of the
RTL SoCs.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
The ingress filter registers use 2 bits for each port to define the filtering
state, whereas the egress filter uses 1 bit. So for for the ingress filter
the register offset for a given port is:
(port >> 4) << 4: since there are 16 entries in a register of 32 bits
and for the egress filter:
(port >> 5) << 4: since there are 32 entries in a register of 32 bits
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Configure a sane L2 learning configuration upon DSA driver load so that the
switch can start learning L2 addresses. Also configure the correct flood masks
for broadcast and unknown unicast traffice.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This adds RTL93xx-specific MAC configuration routines that allow also configuration
of 10GBit links for phylink. There is support for the Realtek-specific HISGMI
protocol.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This adds support for offloading TC flower by using the Packet Inspection Engine
of the RTL-SoCs. Basic infrastructure support is provide with callbacks to the
tc subsystem and support for HW packet counters.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
All RTL SoCs addresss PHYs via their port number, which is mapped to an
SMI address. Add support for configuring this mapping via the .dts on all
SoCs apart from the 839x, where the mapping to the 64 ports is fixed.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
On RTL83xx enable learning of the MAC source address of the CPU port
from outgoing packets. Add documentation on bit fields. On RTL93xx
enable port-mask usage and the use of internal priority, these
SoCs automatically learn the MAC.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Remove the storm control and attack warnings from the IRQ handler
of the Ethernet driver. There was no consequence to the detection
and the kernel can also handle at least the attacks itself.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This enlarges the size of the TX ring buffer, which prevents warnings
when the buffer runs out of space.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This fixes:
ERROR: "switch_generic_set_link" [drivers/net/phy/b53/b53_common.ko] undefined!
At some point all packages for swconfig drivers were dropped and targets
were meant to have them built into kernels. It seems b53 (re-)gained its
kmod-switch-bcm53xx however and b53 needs to be built as module.
Fixes: b2cfed48f6 ("Revert "swconfig: fix Broadcom b53 support"")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Add Vladimir Oltean's "net: dsa: don't set skb->offload_fwd_mark when
not offloading the bridge"
This covers cases where packets received by an upstream switch must be
forwarded back on the same port, which skb->offload_fwd_mark normally
prevents.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This reverts commit 8f9cd1af0f.
That commit was meant to add a single EXPORT_SYMBOL_GPL() but it
actually also added few .of_match_table-s. One commit should handle one
thing and should not introduce unrelated changes.
Regarding actual changes:
1. EXPORT_SYMBOL_GPL is not required as we don't build swconfig drivers
as modules.
2. PHY drivers must not have .of_match_table. That is allowed for MDIO
drivers. This could work for some time (although is didn't for me on
bcm53xx) but does not with kernel 5.10. It causes a soft lockup and
upstream developers confirmed it's an unsupported design.
Link: https://lore.kernel.org/netdev/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com/t/#mf80e472f35ee23f7a75cbf5b1e101a17ab3a64a3
Cc: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This has testing support for 7 months. Time to switch.
TL-WDR4900 is disabled due to kernel size limitation.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Three missing symbols were found during mpc85xx/p2020 compilation.
While at it, CONFIG_FSL_ENETC_MDIO is moved to generic config
for consistency.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[move CONFIG_FSL_ENETC_MDIO, remove redundant definitions, adjust
commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
With the upgrade to kernel 5.10 per default the old version is no
longer required to be in tree.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When KERNEL_PERF_EVENTS is enabled in OpenWrt, or PERF_EVENTS in the
kernel config, the RPI_AXIPERF is exposed. Add it to the subtarget
kernel configs to avoid build failures.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
When building an image for the bcm27xx target, some combinations of
config options will fail to build due the SND_SOC_AD193X_I2C and
SND_SOC_AD193X_SPI kernel config symbols being missing.
The problem only occurs on bcm27xx as the target contains a patch that
modifies the Kconfig file containing the symbols; in the vanilla kernel,
there is no string after the tristate keyword so the symbol is not
exposed.
The _I2C symbol depends on I2C, which is enabled in the kernel configs
of all bcm27xx subtargets.
The _SPI symbol depends on SPI_MASTER, which is exposed by either
kmod-mmc-spi, kmod-spi-bitbang, kmod-spi-dev, kmod-spi-bcm2835 or
kmod-spi-bcm2835-aux.
Both symbols are defined in the sound/soc/codecs directory, which is
only included when SND_SOC is enabled, so this problem doesn't occur
when kmod-sound-soc-core is not enabled. As the
kmod-sound-soc-bcm2835-i2s package disables the SND_SOC_AD193X_SPI
symbol, it also doesn't occur when kmod-sound-soc-bcm2835-i2s is
enabled.
As there are several possible config combinations that do exhibit this
problem, it is best to solve it by adding the missing symbols to the
subtarget kernel configs. By doing this we can remove them from the
kmod-sound-soc-bcm2835-i2s package.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Switch port order was reversed due to reading the internal labling
(which mismatches the one on the case).
Signed-off-by: David Bauer <mail@david-bauer.net>
The cortex53 subtarget was missing multiple config options and the other
targets just defined some options which are not needed.
Fixes: 83672f506d ("sunxi: add testing Linux 5.10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel 5.4 configuration activated SATA Port Multiplier support, add
it to kernel 5.10 too.
Fixes: 83672f506d ("sunxi: add testing Linux 5.10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SATA_PMP option is no longer exposed when no SATA host driver is enabled
since upstream linux commit bd322af15ce9 ("ata: make SATA_PMP option
selectable only if any SATA host driver is enabled").
Commit 1bb3f593ee ("kirkwood: update config for kernel 5.10") manually
added CONFIG_SATA_PMP=y to config file, but the config will disappear for
every kernel_oldconfig refresh.
To prevent this, a small hack is added, which selects SATA_HOST
automatically when SATA_PMP is enabled. This patch can be dropped if
SATA_MV is ever re-added into kernel config file.
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[Move patch to generic/hack-5.10]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These instructions are repeated for a few devices now, let's move
them to shared definition so we do not repeat ourselves too often.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The bootloader can leave the GPIO expander in a state which doesn't have
output drivers enabled so GPIOs will properly work for input but output
operations will have no effect.
To avoid disrupting the boot in case the bootloader left direction and
data registers in an inconsistent state (e.g. pulling SoC's reset to 0)
reconfigure everything as input.
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Globalscale MOCHAbin is a Armada 7040 based development board.
Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element
Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.
Installation:
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/
$ in.tftpd -L -s bin/targets/mvebu/cortexa72/
Connect to the device UART via microUSB port and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Set the ethernet device (Example for the 1G WAN):
$ setenv ethact mvpp2-2
Ping server to confirm network is working:
$ ping $serverip
Using mvpp2-2 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin
$ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb
Boot the image:
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Hit any key to stop the autoboot.
Reset U-boot env and set the bootcmd:
$ env default -a
$ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}'
Optionally I would advise to edit the console env variable to remove earlycon as that
causes the kernel to never use the driver for the serial console.
Earlycon should be used only for debugging before the kernel can configure the console
and will otherwise cause various issues with the console.
$ setenv console 'console=ttyS0,115200'
Save and reset
$ saveenv
$ reset
OpenWrt should boot from eMMC now.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
When trying to add support for another device with Micron NAND chips,
it was discovered that the default setting in the kernel source does
not work with Micron Chips, since the device trees setting is
overwritten and hard coded by the kernel xway_nand driver. This was
the original reason for this PR.
A kernel patch sets the default ECC mode to soft without overwriting
the device tree settings and the device tree for devices using it
are updated with new parameters because the old ones are deprecated
by torvalds/linux@533af69.
A patch for kernel 5.4 is provided to support the new settings
because kernel 5.4 does not support it.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This backports a fix proposed for upstream kernel to fix overwriting
the NAND ECC engine in device tree.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All subtargets only provide files and patches for Linux 5.10 by now
so there is little use for the old Linux 5.4 stuff. Remove it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Armvirt is a development and testing platform and should therefore use
the latest OpenWrt Kernel by default.
Tested via qemu.
Acked-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Malta is a development and testing platform and should therefore use the
latest OpenWrt Kernel by default.
Acked-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Add common features 'gpio', 'nand', 'pci', 'pcie', 'squashfs' and 'usb'
for all mediatek targets, add 'display' and 'usbgadget' for MT7623.
Sort features alphabetically while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
User reported that R64 doesn't provide power to the mPCIe slot in case
the PCIe port is disabled as it is when selecting the SATA
configuration. As users may still want to use USB-connected mPCIe
modules in CN8 slot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Netgear Nighthawk AC2100 is another name of the Netgear R6700v2.
Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
[adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
With the various variants of Netgear R**** devices, make it more
obvious which image should be used for the R7200.
Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
[provide proper commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds "KERNEL_TESTING_PATCHVER:=5.10" to the Makefile in
realtek target to allow using Kernel 5.10 for testing.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
On the devices with PoE support, the secondary UART (uart1) on the SoC
is used to communicate between the SoC and controller.
Enable the secondary UART on the following devices:
- D-Link DGS-1210-10P
- Netgear GS110TPP v1
- Netgear GS310TP v1
- ZyXEL GS1900-8HP v1/v2
- ZyXEL GS1900-10HP
- ZyXEL GS1900-24HP v2
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The new backported GPIO driver supports interrupt, so use gpio-keys
instead of gpio-keys-polled for keys connected to the internal GPIO
controller.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
this patch includes the following changes:
- adjust mapping for the new driver
- GPIO 24 -> GPIO 0
- GPIO 47 -> GPIO 0 (+ disabling system LED)
- disable pins in the invalid range
(out of the range 0-31 of the new driver)
- are these pins on the external RTL8231 (&gpio1)?
- GPIO 67 (-> GPIO 3 on &gpio1?)
- GPIO 94 (-> GPIO 30 on &gpio1?)
- drop "indirect-access-bus-id" property from gpio0 node in device dts
files
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
dsa_to_port function in 5.10 returns dsa_port from the port list in
dsa_switch_tree, but the tree is built when the switch is registered
by dsa_register_switch and it's null in rtl83xx_mdio_probe.
So, we need to use dsa_to_port after the registration of the switch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch adds a pinctrl-single pinmux node to allow disabling system
LED and enabling GPIO 0 (old driver: GPIO 24).
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
this patch fixes the following errors when compiling:
- dsa_switch_alloc is removed[1]
- a parameter "enum dsa_tag_protocol mprot" is added to dsa_tag_protocol
in dsa_switch_ops (include/net/dsa.h)
- several paramters are added to "phylink_mac_link_up" in dsa_switch_ops
(include/net/dsa.h)
added:
- int speed
- int duplex
- bool tx_pause
- bool rx_pause
- a parameter "struct switchdev_trans *trans" is added to
port_vlan_filtering in dsa_switch_ops (include/net/dsa.h)
[1]: https://lore.kernel.org/lkml/20191020031941.3805884-17-vivien.didelot@gmail.com/
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
this patch fixes the following errors when compiling:
- "unsigned int txqueue" is added as an additional parameter of
ndo_tx_timeout in net_device_ops (include/linux/netdevice.h)
- "mac_link_state" in phylink_mac_ops (include/linux/phylink.h)
is renamed to "mac_pcs_get_state" and changed the return value
to void from int
- several parameters are added to "mac_link_up" in phylink_mac_ops
(include/linux/phylink.h) and the order of the parameters is
changed
added:
- int speed
- int duplex
- bool tx_pause
- bool rx_pause
- a parameter "phy_interface_t *interface" is added to of_get_phy_mode
(drivers/of/of_net.c) and returns the state instead of phy mode
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
this patch updates SoC dtsi (rtl838x.dtsi, rtl930x.dtsi) for the
following backported drivers:
- gpio-realtek-otto (5.13)
- spi-realtek-rtl (5.12)
- irq-realtek-rtl (5.12)
And, disable SoC GPIO node (gpio0) in rtl930x.dtsi in dts-5.10.
Currently, the upstreamed driver doesn't support the GPIO controller on
RTL930x SoC.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
the following changes are included in this patch:
- node is enabled by default, drop 'status = "okay"'
- adjust order of "compatible" lines and "reg" lines
- add a new blank line before fixed-link node in rtl830x.dtsi
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch adds "dts-5.10" directory to use backported drivers.
There are several specification changes in the new drivers, so there
are some compatibility issues in using dts/dtsi files for 5.4.
The old DTS files are moved to "dts-5.4", so their corresponding
kernel version is obvious as well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[change "dts" to "dts-5.4", adjust Makefile]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The following line is already defined in arch/mips/Kbuild.platforms by
300-mips-add-rtl838x-platform.patch.
platform-$(CONFIG_RTL838X) += rtl838x/
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
A macro with the same name is provided in asm/pgtable.h in Kernel 5.10,
use it and drop from ioremap.h.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch backports "irq-realtek-rtl" driver to Kernel 5.10 from 5.12.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To use backported irq driver, drop old irq driver from realtek target
and call irqchip_init() in setup.c.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To backport the upstreamed driver (gpio-realtek-otto) from 5.13, drop the
old driver from realtek target.
And, modify 301-gpio-add-rtl838x-driver.patch to remove rtl838x GPIO
support and rename it only for rtl8231 GPIO support.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch backports "spi-realtek-rtl" driver to Kernel 5.10 from 5.12.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To backport the upstreamed driver (spi-realtek-rtl) from 5.12, drop the
old driver from realtek target.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
this patch copies the following files from 5.4 to 5.10:
- config-5.4 -> config-5.10
- files-5.4/ -> files-5.10/
- patches-5.4/ -> patches-5.10/
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rebase on change in files-5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Expose I2C busses with a chardev device. This is required to control the
PSE controller on the Ubiquiti UniFi Flex Switch.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
MediaTek MT7621AT
16M SPI-NOR Macronix MX25L12835FMI
Microchip PD69104B1 4-Channel PoE-PSE controller
TI TPS2373 PoE-PD controller
PoE-Controller
--------------
By default, the PoE outputs do not work with OpenWrt. To make them output
power, install the "poemgr" package from the packages feed.
This package can control the PD69104B1 PSE controller.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt" via SSH.
2. Add the uboot-envtools configuration file /etc/fw_env.config with the
following content
$ echo "/dev/mtd1 0x0 0x1000 0x10000 1" > /etc/fw_env.config
3. Update the bootloader environment.
$ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
fdt rm /signature; bootubnt"
$ fw_setenv bootcmd "run boot_openwrt"
4. Transfer the OpenWrt sysupgrade image to the device using SCP.
5. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
6. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4
7. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock6
$ dd if=openwrt.bin of=/dev/mtdblock7
8. Reboot the device. It should boot into OpenWrt.
Restore to UniFi
----------------
To restore the vendor firmware, follow the Ubiquiti UniFi TFTP
recovery guide for access points. The process is the same for
the Flex switch.
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on the AP152 reference board
Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
data rate) Based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal
reflector
- Power, LAN, WLAN5G Blue LEDs
- 3x Blue LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[convert to nvmem, fix MAC assignment in 11-ath10k-caldata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This backports the upstream commit:
leds: lp55xx: Initialize enable GPIO direction to output
Without it under kernel 5.10 on Asus MAP-AC2200
the LED driver will fail probing:
[ 1.947521] lp5523x: probe of 0-0032 failed with error -22
After the backported fix:
[ 1.873236] lp5523x 0-0032: lp5523 Programmable led chip found
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ipq4029/gl-b1300]
Tested-by: Nick Hainke <vincent@systemli.org> [ipq4019/fritzbox-7530
ipq4019/fritzbox-4040
ipq4019/sxtsq-5ac]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq4019/map-ac2200]
Add kernel 5.10 as the testing kernel to ipq40xx to
get wider testing.
The following devices failed to build with buildbot settings and all
feeds installed (apparently due to kernel size):
* cell-c rtl30vw
* compex wpj428
* devolo magic 2 next
* engenius emr3500
* glinet gl-b1300
* glinet gl-s1300
* qcom ap-dk01.1-c1
* qcom ap-dk04.1-c1
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Nick Hainke <vincent@systemli.org> [ipq4019/fritzbox-7530
ipq4019/fritzbox-4040
ipq4019/sxtsq-5ac]
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ipq4029/gl-b1300]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq4019/map-ac2200]
[add tested-by and note about failed devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MDIO drivers were moved into their own sub directory of networking drivers.
This has caused the AR40xx driver to probe before MDIO drivers and that wont
work as it depends on the MDIO bus to be up so it can be fetched.
Lets solve it by moving the AR40xx into MDIO folder so they get probed like
before.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
This is a required ethtool op since kernel 5.7.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In kernel v5.5 of_get_phy_mode had its API changed, so its now returning 0
or errors instead of phymode.
Phymode is now returning by passing a pointer to phy_interface_t where it
will be stored.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Copy config from 5.4 and run "make kernel_oldconfig".
Select default ("N") for all new symbols.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[make commit message more explicit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Refresh the kernel patches on top of 5.10 so they apply.
Manually fixup the 705-net-add-qualcomm-ar40xx-phy.patch
to apply.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
USB and SDHCI LDO DTS patches have been upstreamed into 5.12, so
replace the local versions with upstreamed ones.
Reorder, and clearly mark the kernel version.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
I-O DATA WN-DX2033GR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : Raw NAND 128 MiB (Macronix MX30LF1G18AC-TI)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, MediaTek MT7603E
- 5 GHz : 4T4R, MediaTek MT7615
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LEDs/Keys : 2x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J5: 3.3V, TX, RX, NC, GND from triangle mark
- 57600n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs image:
1. Boot WN-DX2033GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
to perform firmware update
4. On the initramfs image, download the sysupgrade.bin image to the
device and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- The hardware of WN-DX2033GR and WN-AX2033GR are almost the same, and
it is certified under the same radio-wave related regulations in Japan
- The last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" (called as "combo
image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't
- uImage magic ( 0x0 - 0x3 ) : 0x434F4D42 ("COMB")
- header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
- image name (0x20 - 0x37) : model ID and firmware versions
- data length (0x38 - 0x3b) : kernel + rootfs
- data crc32 (0x3c - 0x3f) : kernel + rootfs
- There are 2x important flags in the flash:
- bootnum : select os partition for booting (persist, 0x4)
- 0x01: firmware
- 0x02: firmware_2
- debugflag : allow interrupt kernel loader, it's named as "Z-LOADER"
(Factory, 0xFE75)
- 0x00: disable debug
- 0x01: enable debug
MAC addresses:
LAN : 50:41:B9:xx:xx:90 (Factory, 0xE000 (hex) / Ubootenv, ethaddr (text))
WAN : 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex))
2.4 GHz : 50:41:B9:xx:xx:90 (Factory, 0x4 (hex))
5 GHz : 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
GPIOs > 31 require special handling. This patch fixes both the
initialisation and direction get/set operations.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Add additional header information required for newer
bootloaders found on DIR-2660-A1 & A2.
Also remove the MTD splitter compatible from the second firmware
partition, as OpenWrt only supports handling of the first one.
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
[rephrase commit message, remove removal of read-only flags]
Signed-off-by: David Bauer <mail@david-bauer.net>
The rockchip platform supports squashfs SD card images. However, the
resulting image is not padded to completely fill the rootfs partition.
Because of that, the f2fs overlay might not be erased, resulting in
uci-defaults not bing executed or the configuration not being erased,
even though drop config was selected.
Modify the image generation process so the image is padded to cover the
entire root filesystem partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
Remove use of DEVICE_TITLE in favor of the
DEVICE_VENDOR and DEVICE_MODEL as used by
all other targets.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Remove use of DEVICE_TITLE in favor of the
DEVICE_VENDOR and DEVICE_MODEL as used by
all other targets.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Meraki wrote the ethernet MAC-address of the device
onto the eeprom (AT24C64) at the fixed location 0x66
to 0x6C. Let's fetch it from there.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
broke support for Meraki MR32 and this patch makes the replacement
configurable allowing for specifying the @ or - or whatever character
that is desired to retain backwards compatibility with existing devices.
For example, this patch includes the fix for the Meraki MR32 in
target/linux/bcm53xx/image for meraki_mr32:
DEVICE_DTS_DELIMITER := @
DEVICE_DTS_CONFIG := config@1
Fixes: 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Signed-off-by: Damien Mascord <tusker@tusker.org>
[Added tags, checkpatch.pl fixes, noted that this is for old stuff]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
With GCC11, memcpy doesn't work here as it assumes a size of 0. Use
ioremap to avoid it.
Fixed parameter type to match board_get_mac_address.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This fixes:
Distributed Switch Architecture (NET_DSA) [Y/n/m/?] y
Tag driver for Atheros AR9331 SoC with built-in switch (NET_DSA_TAG_AR9331) [N/m/y/?] n
Tag driver for Broadcom switches using in-frame headers (NET_DSA_TAG_BRCM) [N/m/y/?] n
Tag driver for Broadcom legacy switches using in-frame headers (NET_DSA_TAG_BRCM_LEGACY) [N/m/y/?] (NEW)
Error in reading or end of file.
Fixes: 8fa1b576bb ("linux: update b53 upstream driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Specifying serial in bootargs is not needed since the commit
ffeb37047e ("procd: update to git HEAD"). It's thanks to the procd
commit 2cfc26f8456a ("inittab: detect active console from kernel if no
console= specified").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Build cortexa7 subtarget with DSA driver for MDIO-connected Broadcom
BCM53xxx switches. This is needed for the Lamobo R1 aka. BananaPi
BPi-R1 board which comes with such a switch IC.
Remove old swconfig driver from target kernel config as the only board
using it is now supported by the DSA driver.
No changes to device tree are needed as upstream DTS already got a
DSA switch definition and we are just using that upstream source.
Update default network config of the Lamobo R1 to create lan bridge
with all 4 lan ports.
Introduce DEVICE_COMPAT_VERSION for the board to inform users about
having the re-create their network configuration and add device alias
as Bananapi BPi-R1 while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Changes from 5.4 to 5.10:
-------------------------
- patches from 5.4 are all upstream for 5.10 execpt for
0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch
- disable block device data integrity (DIF/DIX/T10) in default config
(CONFIG_BLK_DEV_INTEGRITY)
This feature is only supported by:
- Enterprise SAS/SCSI HBAs and Disks
- Software raid
- NVMEs with metadata capabilities (most don't have this)
None of which are part of any octeontx boards.
- arm64 TEXT_OFFSET (0x80000) has been removed after 5.4
This will break Uimages with kernel load addresses that aren't 2MiB
aligned any longer. Resulting in the kernel silently fail to boot.
For Gatworks newport boards for example, the uimage kernel load
and execute address is 0x20080000. These need to be changed to
0x20000000 when running kernels beyond 5.4.
Tested-on: Gateworks Newport GW64xx
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Linksyses Audi EA3500 and Viper E4200/E4500 have too small kernel
partition size when kernel 5.10 is used. This patch change kernel
partition to maximum size allowed by u-boot.
Kernel size is overlapping rootfs now, like mvebu Linksyses and stock
partition table. It fix back to stock via sysupgrade, which was broken
since 18.06.
Fixes: 9808b9ae02 ("kirkwood: switch to kernel 4.9")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HPv2
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: W631GG8MB-12 128 MiB DDR3 SDRAM
(stock firmware is configured to use only 64 MiB)
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
24 ethernet port PoE status LEDs
2 SFP status/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESTORE" button on front panel
1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J41) with populated standard pin connector on
the left edge of the PCB, angled towards the side.
The casing has a rectangular cutout on the side that provides
external access to these pins.
Pinout (front to back):
+ GND
+ TX
+ RX
+ VCC
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
OEM upgrade method:
(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
