This can be useful when a DFS channel is configured, as the ACS channel
list is taken into account when switching channels after a radar event.
For example, this allows to prevent the SRD channels from being used in
that case.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[reorder structure]
Signed-off-by: David Bauer <mail@david-bauer.net>
Removing i2c pxa slave
The i2c-pxa is typically not use in slave mode. It does not make sense
to have slave mode enabled by default.
Having slave mode enabled prevents the i2c controller from being reset
if a real slave device such as an SFP is attached to the i2c-pxa bus and
locks it up.
Disable slave mode so that the i2c controller can be reset if the bus is
locked up.
If someone actually has a need for pxa slave mode this can be enabled in
kernel config.
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
Remove leds-apu2 out of tree driver. There is a new upstream device gpio
and leds driver stack available for the APUv2 and APUv3 boards from pc
egnines. This new driver stack was add in kernel version 4.15.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
ath9k will already fallback on software-crypto for chipsets not
supporting IEEE802.11w (MFP). So advertising MFP is not dependent
on disabling HW crypto for all traffic entirely.
Tested on Sonicwall SonicPoint Ni (AR9132)
Signed-off-by: David Bauer <mail@david-bauer.net>
mac80211_get_addr is called from mac80211_generate_mac, where the local variable
initialisation id="${macidx:-0}" suggests that macidx is not always defined.
Probably, idx was supposed to be used instead of $(($macidx + 1)).
Fixes: 4d99db168c ("mac80211: try to get interface addresses from wiphy sysfs 'addresses' if no mask is set")
Signed-off-by: Leon M. George <leon@georgemail.eu>
This option allows adding the ath9k ADC register output as a source
of randomness into the Linux entropy pool at sufficient quality
random data (at least 10 bits and up to 22 bits of min-entropy for
a 32-bit value).
Fixes FS#1444
Signed-off-by: Alan Swanson <reiver@improbability.net>
All devices are using nand images. Built-in MMC/SD modules are not needed
anymore.
Run tested: pogo v4
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This updates to the last firmware version before the switch to building
from the common firmware branch, which introduces various issues.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
This reverts commit 9e467a764b.
The Raspberry Pi firmware recently switched to building from the common
firmware branch. This introduces changes in the core clock handling,
causing various issues.
E.g. enable_uart=1 no longer fixes the core clock frequency to 250MHz.
When the disable-bt DT overlay is not loaded, the core clock frequency
is increased to 400MHz. As a result, the UART baud rate is no longer
correct, and this causes garbled serial console, or communication
problems with HATs that use the UART.
As a workaround, the core clock could be fixed to 250MHz by adding
'core_freq=250' in /boot/config.txt, but as there appear to be other
issues than just the UART being broken, the safer bet is to revert the
firmware for now.
Upstream bug: https://github.com/raspberrypi/firmware/issues/1376
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
As reported in https://github.com/openwrt/packages/issues/12072, the
imagebuilder fails due to a dependency resolution error when the userspace
packages are built using a target that has a different kernel version than
that which is being run. To resolve this, add a virtual kernel package with
the conditional dependency currently used in sqm-scripts. The idea is to
move the sqm-scripts dependency to this virtual package, which hopefully
should be consistent with the actual kernel module being built.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This patch adds support for 2 new uci sections.
config wifi-vlan
# iface is optional. if it is not defined the vlan will apply
# to all interfaces
option iface default_radio0
option name guest
option vid 100
option network guest
config wifi-station
# iface is optional. if it is not defined the station will apply
# to all interfaces
option iface default_radio0
# mac is optional. if it is not defined it will be a catch all
# for any sta using this key
option mac '00:11:22:33:44:55'
# vid is optional. if it is not defined, the sta will be part of
# the primary iface.
option vid 100
option key testtest
With this patch applied it is possible to use multiple PSKs on a single BSS.
Signed-off-by: John Crispin <john@phrozen.org>
Add kmod for the ST LSM6DSX IMU driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[fixed missing regmap module dependencies]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since commit 910df3f06c we have build in
on all X86/64 platforms the gpio-it87 driver.
Since this change I am getting the following error message on boot.
> kern.err kernel: [ 1.009416] gpio_it87: no device
I do not have this device on my system. To prevent the nonsensical
message and the loading of the module I have added this as a package, so
that it can be installed later or during image building.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
From: Rui Salvaterra <rsalvaterra@gmail.com>
Date: Mon, 25 May 2020 14:49:07 +0100
Subject: [PATCH] rt2800: enable MFP support unconditionally
This gives us WPA3 support out of the box without having to manually disable
hardware crypto. The driver will fall back to software crypto if the connection
requires management frame protection.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When configuring the radio in legacy mode from luci, the htmode is not set
correctly to NOHT, causing the radio in mesh mode to be set to HT40.
Signed-off-by: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
Add a local hack to prevent the Broadcom WPA authenticator process from
inheriting the lock descriptor 1000 used to prevent concurrent executions
of the init script.
Without this fix, repeated invocations of /etc/init.d/network, e.g. for
obtaining the enabled state, would hang forever.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This fixes the following compile error seen on the mpc85xx target:
CC [M] /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.o
In file included from /builder/shared-workdir/build/staging_dir/toolchain-powerpc_8540_gcc-8.4.0_musl/include/stddef.h:17,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/include/uapi/linux/wireless.h:77,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/include/linux/wireless.h:13,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.c:89:
/builder/shared-workdir/build/staging_dir/toolchain-powerpc_8540_gcc-8.4.0_musl/include/bits/alltypes.h:106:15: error: conflicting types for 'ptrdiff_t'
typedef _Addr ptrdiff_t;
^~~~~~~~~
In file included from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/types.h:4,
from ./include/linux/list.h:5,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/list.h:3,
from ./include/linux/module.h:9,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/module.h:3,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.c:79:
./include/linux/types.h:65:28: note: previous declaration of 'ptrdiff_t' was here
typedef __kernel_ptrdiff_t ptrdiff_t;
^~~~~~~~~
scripts/Makefile.build:265: recipe for target '/linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.o' failed
Fixes: 289c632425 ("mac80211: Update to version 5.7-rc3-1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
The 131-Revert-mac80211-aes-cmac-switch-to-shash-CMAC-driver.patch patch
was manually adapted to the changes in kernel 5.7.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport to the latest minor version.
The removed patch was a backport from the upstream kernel which is now
integrated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the package to contain the kernel object (.ko) file instead
of the plain object (.o) file.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
When CONFIG_AUTOREMOVE is enabled, CFE binaries are removed before the
image creation.
Install CFE binaries to kernel directory and let autoremove clean the
files in PKG_BUILD_DIR.
Also drop unneeded tar cmd/options.
Fixes: dcee4eaa42 ("bcm63xx-cfe: add package with CFE RAM binaries")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
CFE RAM is a second stage bootloader which is usually loaded by CFE ROM
(first stage bootloader) from a JFFS2 partition stored on the NAND.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This drops kernel version switches for versions not supported by
OpenWrt master at the moment. This only adjusts local code, but
doesn't touch patches to existing external packages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The user can now enable the ACK timeout estimation algorithm (dynack)
for drivers that support it.
It is also expected that the distance config accepts the same values as:
$ iw phyX set distance XXX
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
* uci state was not getting reset properly during teardown
* AP+STA co-exist state was not flushed properly upon channel switch
* remove a debug logger call
* properly teardown supplicant instances when they get disabled
* add md5 config support for supplicant
* don't call wpa_supplicant_prepare_interface twice
Signed-off-by: John Crispin <john@phrozen.org>
Pulls in workaround for TX rate code firmware bug which might as well
help track it down via different printk()s and thus possibly provide
more clue for proper fix.
Firmware currently sends wrong (0xff) TX rate code which causes
WARN_ONCE, so the workaround just changes this bogus value (0xff) into 0.
For 5.4 it also pulls in tx-queue-wake throttling patch "ath10k: Restart
xmit queues below low-water mark", which should improve performance with
high number of concurrent TCP streams.
Ref: https://github.com/greearb/ath10k-ct/pull/129
Signed-off-by: Petr Štetiar <ynezz@true.cz>
bef8f8a5966d mt76: mt7615: remove a stray if statement
89bd7199487f mt76: remove variable 'val' set but not used
ee8ac234b84e mt76: mt7615: introduce mt7615_mcu_fill_msg
4999db4668f0 mt76: mt7615: introduce mt7615_mcu_wait_response
8ce6e40eba03 mt76: mt7615: cleanup fw queue just for mmio devices
9d1d2ee9add3 mt76: mt7615: introduce mt7615_init_device routine
7fbd2a57cea4 mt76: always init to 0 mcu messages
3b277cf18d95 mt76: mt7615: introduce mt7615_mcu_send_message routine
2a4132a55a4f mt76: mt7615: add mt7615_mcu_ops data structure
9ba71749a122 mt76: mt7615: move mt7615_mcu_set_bmc to mt7615_mcu_ops
2e991f3e8cdd mt76: mt7615: move mt7615_mcu_set_sta in mt7615_mcu_ops
56852057cb90 mt76: mt7615: rely on skb API for mt7615_mcu_set_eeprom
642ecd978887 mt76: mt7615: rework mt7615_mcu_set_bss_info using skb APIs
2b0810af4a52 mt76: mt7615: move more mcu commands in mt7615_mcu_ops data structure
7a6285e63d88 mt76: mt7615: introduce MCU_FW_PREFIX for fw mcu commands
e536b42ebc7d mt76: mt7615: introduce mt7615_register_map
fccbdb628ffd mt76: mt7615: add mt7663e support to mt7615_reg_map
d42244e9255c mt76: mt7615: add mt7663e support to mt7615_{driver,firmware}_own
aebbe088127f mt76: mt7615: add mt7663e support to mt7615_mcu_set_eeprom
28e22d07f892 mt76: mt7615: introduce mt7615_eeprom_parse_hw_band_cap routine
167428592647 mt76: mt7615: introduce mt7615_init_mac_chain routine
23ca7acfc856 mt76: mt7615: introduce uni cmd command types
c4171728cf70 mt76: mt7615: introduce set_bmc and st_sta for uni commands
9e5c76d2310a mt76: mt7615: add more uni mcu commands
779b2cebc147 mt76: mt7615: introduce set_ba uni command
21ee7da00f0a mt76: mt7615: get rid of sta_rec_wtbl data structure
2097f74f664c mt76: mt7615: introduce mt7663e support
8e9cd01228d0 mt7615: sync Kconfig with upstream
3b4f93840950 mt76: add memory barrier to DMA queue kick
8d301ace8ed7 mt76: mt7615: fix mt7663e firmware struct endianness
9bc1850ce711 mt76: mt7615: fix endianness in unified command
a1b9b7d94aa0 mt76: mt7615: add missing declaration in mt7615.h
6e4b2a709fe7 mt76: sync Makefile with upstream
258dfb6afb30 mt76: mt76x02u: Add support for newer versions of the XBox One wifi adapter
9c3d84b62cc0 mt76: mt76x2u: introduce Mercury UD13 support
ea8ea71933ca mt76: mt76x0: pci: add mt7610 PCI ID
9d555f82d329 mt76: mt7615: modify mt7615_ampdu_stat_read for each phy
8bd26d6c3172 mt76: mt7615: enable aggr_stats for both phy
1315afa511e0 mt76: mt7615: cleanup mib related defines and structs
072b50c61e0e mt76: mt7615: add more useful Tx mib counters
b23ff3e9343a mt76: mt7663: fix mt7615_mac_cca_stats_reset routine
294abe47c9b2 mt76: mt7663: enable nf estimation
d2d7bf2243f6 mt76: mt7615: make scs configurable per phy
908a2cfab88f mt76: mt7663: disable RDD commands
eaef0a268b95 mt76: mt7615: add ethool support to mt7663 driver
96e07ef1113d mt76: mt7615: introduce mt7615_mcu_set_channel_domain mcu command
67182f36e3be mt76: mt7663: keep Rx filters as the default
e6a3f3ffe53a mt76: mt7615: introduce hw scan support
12ecd5ba2146 mt76: mt7615: introduce scheduled scan support
f6ab0bee3172 mt76: mt7615: introduce BSS absence event
f208a9430044 mt76: mt7615: introduce rlm tlv in bss_info mcu command
ea4f4d216dbe mt76: mt7615: remove unnecessary register operations
72c9380e70f9 mt76: add headroom and tailroom to mt76_mcu_ops data structure
63e14669e09d mt76: mt7615: introduce mt7663u support to mt7615_write_txwi
29d359ac7626 mt76: mt7615: introduce mt7615_mac_update_rate_desc routine
1f1dd2cb5b49 mt76: mt7615: introduce __mt7663_load_firmware routine
cb6dcfd3cf13 mt76: mt7615: move mt7615_mac_wtbl_addr in mac.h
d28e8e7ef912 mt76: mt76u: rely on mt7622 queue scheme for mt7663u
f78cf8957aba mt76: mt7615: rework wtbl key configuration
2829497aaaf5 mt76: mt7615: introduce mt7615_wtbl_desc data structure
02c9ec4a15e7 mt76: mt7615: add address parameter to mt7615_eeprom_init
e9c640c0a79e mt76: mt7663: correct the name of the rom patch
1e8b2fe5ab03 mt76: mt7615: do not always reset the dfs state setting the channel
ec0ea46dacf9 mt76: mt7615: Delete an error message in mt7622_wmac_probe()
d16a4698f1ac mt76: mt7615: disable merge of OTP ROM data by default
2b58998bb594 mt76: mt7615: add support for applying DC offset calibration from EEPROM
55198aafb756 mt76: mt7615: add support for applying tx DPD calibration from EEPROM
5a1eaa38d380 mt76: mt7603: disable merge of OTP ROM data by default
bf60f43b12fb mt76: mt76x2: disable merge of OTP ROM data by default
9406eb1d110f mt76: mt7615: fix endian issues in applying flash calibration data
66d00b8c9dac mt76: mt7615: fix possible division by 0 in mt7615_mac_update_mib_stats
25d812dddcf8 mt76: mt7663: fix aggr range entry in debugfs
08b8bd2bc915 mt76: mt7615: disable hw/sched scan ops for non-offload firmware
8fb1cd20a776 mt76: mt7615: set hw scan limits only for firmware with offload support
05b23d7478fe mt76: mt7615: rework IRQ handling to prepare for MSI support
b92c0d576769 mt76: mt7622: fix DMA unmap length
03daa60ca69c mt76: mt7663: fix DMA unmap length
5f2f676b1f01 mt76: mt7615: enable MSI by default
5822911f8026 mt76: remove unnecessary annotations
a7035bce8517 mt76: mt7615: fix possible deadlock in mt7615_stop
d4e6e225bc06 mt76: mt7615: move core shared code in mt7615-common module
94827d2033c7 mt76: mt7615: introduce mt7663u support
36591dd35f91 mt76: mt7615: enable scs for mt7663 driver
bd80144cb5be mt76: mt7615: disable aspm by default
9dcb60b78ede mt76: mt7615: provide aid info to the mcu
6e443e89cce2 mt76: remove PS_NULLFUNC_STACK capability
ea133325faa6 mt76: mt7663: introduce 802.11 PS support in sta mode
ff3869b38cf2 mt76: mt7615: make Kconfig entry obvious for MT7663E
01fd34f3a6c5 mt76: mt7615: fix sta ampdu factor for VHT
e5adbb2077e2 mt76: fix A-MPDU density handling
d73e3a23a54e mt76: mt7615: use larger rx buffers if VHT is supported
257319e9b07d mt76: mt7615: never use an 802.11b CF-End rate on 5GHz
29a92c5606d6 mt76: mt7603: never use an 802.11b CF-End rate on 5GHz
c0b19ac97c07 mt76: mt7615: adjust timing in mt7615_mac_set_timing to match fw/hw values
1656882f2723 mt76: mt7615: do not adjust MAC timings if the device is not running
4e7ce907faf3 mt76: mt7615: fix tx status rate index calculation
8304b3866100 mt76: mt7603: fix tx status rate index calculation
722d1f47d8ba mt76: add rx queues info to mt76 debugfs
da329ef776b0 mt76: mt7615: parse mcu return code for unified commands
facf74fd506f mt76: mt7615: fix mt7615_firmware_own for mt7663e
e910787a9888 mt76: mt7615: fix max wtbl size for 7663
c9821f7d6a8c mt76: mt7615: fix mt7615_driver_own routine
e35cc532c3d2 mt76: mt7615: fix aid configuration in mt7615_mcu_wtbl_generic_tlv
b6cb91a71fe1 mt76: mt7615: rework mt7615_mac_sta_poll for usb code
b193dd8100f8 mt76: mt7663u: enable AirTimeFairness
31cffa98920f mt76: mt7615: move mcu bss upload before creating the sta
cde3716aa47e mt76: enable TDLS support
1846da5dd417 mt76: mt7615: set spatial extension index
6aaf0299730f mt76: mt7615: fix endian issues in dcoc/txdpd calibration
5de75b745cf9 mt76: mt7663: fix up BMC entry indicated to unicmd firmware
a5f394c5ca48 mt76: mt7615: add sta pointer to mt7615_mcu_add_bss_info signature
1f2f3dda76b9 mt76: mt7615: fix event report in mt7615_mcu_bss_event
c2a3cced36de mt76: mt76x0: enable MCS 8 and MCS9
1afabe78cfc5 mt76: mt7663: add the possibility to load firmware v2
5f3ccc722627 mt76: mt7663: remove check in mt7663_load_n9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Before, only frames with a maximum size of 1528 bytes could be
transmitted between two 802.11s nodes.
For batman-adv for instance, which adds its own header to each frame,
we typically need an MTU of at least 1532 bytes to be able to transmit
without fragmentation.
This patch now increases the maxmimum frame size from 1528 to 1656
bytes.
Tested with two ath10k devices in 802.11s mode, as well as with
batman-adv on top of 802.11s with forwarding disabled.
Fix originally found and developed by Ben Greear.
Link: https://github.com/greearb/ath10k-ct/issues/89
Link: 9e5ab25027
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This fixes a few minor issues (partially cosmetic) in ltq-adsl and
ltq-adsl-fw Makefiles:
- fix PKG_SOURCE_URL and switch to https
- remove non-existant FW_NAME variable
- fix package name for config inclusion
- fix config symbol for debugging
Fixes: 1d0a9d0c04 ("move ltq-adsl")
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The combination +@IPV6:kmod-ipsec6 is not valid, the +a:b
syntax implies the @. Fix it.
Fixes: 2e6b6f9fca ("kernel: add @IPv6 dependency to ipv6 modules")
Reported-by: Oldřich Jedlička (@oldium)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Some FullMAC cfg80211 wireless devices do not support virtual
interfaces, hence there is script logic to keep the existing network
device. Improve this to support renaming the interface if needed and
make sure the existing interface actually belongs to the right phy.
Change calls to 'iw' to avoid outputing warnings and errors to not
confuse users of such devices.
Also bump PKG_RELEASE which has been forgotten in the previous two
mac80211 changes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If we know that we have an encrypted link (based on having had
a key configured for TX in the past) then drop all data frames
in the key selection handler if there's no key anymore.
This fixes an issue with mac80211 internal TXQs - there we can
buffer frames for an encrypted link, but then if the key is no
longer there when they're dequeued, the frames are sent without
encryption. This happens if a station is disconnected while the
frames are still on the TXQ.
Detecting that a link should be encrypted based on a first key
having been configured for TX is fine as there are no use cases
for a connection going from with encryption to no encryption.
With extended key IDs, however, there is a case of having a key
configured for only decryption, so we can't just trigger this
behaviour on a key being configured.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Instead of using the actual interface name, a hard-coded 'wlan0' has
slipped into the script. Replace it.
Fixes: ccf2aa9d4b ("mac80211: detect existing interface before adding")
Reported-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 1b973b54ea.
It turns out act_police is included in the kmod-sched package so this
package turns out to be superfluous and causes file provision conflicts.
Ooooops! Best revert it then.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Updates the 88W8964 firmware used in the Linksys WRT3200ACM and WRT32X
[v9.3.2.6 -> v9.3.2.12]
Removes 0c43219 ("mwlwifi: Fix loading with backports v5.3")
as it has been merged upstream.
Unfortunately, there is a bug wherein Kaloz's repo, the version
detection mechanism for fixing vendor commands doesn't work.
It pulls in the Linux kernel version, which as of this time is
"4.14.y" or "4.19.y"
However, the proper behaviour is that it should pull in the mac80211
backports version which as of now is "5.4.27"
The included patch works around this using a backports define found
only on versions >5.3, "VENDOR_CMD_RAW_DATA".
Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
This adds two fixes for compilation with kernel 5.4:
1. dev_open from include/linux/netdevice.h needs a second parameter
since kernel 5.0:
00f54e68924e ("net: core: dev: Add extack argument to dev_open()")
2. get_ds() macro definition has been dropped since kernel 5.1:
736706bee329 ("get rid of legacy 'get_ds()' function")
Since get_ds() has been just a macro before, replace it in
the driver instead of creating a version switch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since kernel 4.15, init_timer is not available anymore, and has been
replaced by timer_setup. The fixes compilation of wl_linuc.c, which
returned the following errors beforehand (line-wrapped manually):
.../broadcom-wl-5.10.56.27.3/driver/wl_linux.c: In function 'wl_init_timer':
.../broadcom-wl-5.10.56.27.3/driver/wl_linux.c:2576:2: error: implicit
declaration of function 'init_timer'; did you mean 'init_timers'?
[-Werror=implicit-function-declaration]
init_timer(&t->timer);
^~~~~~~~~~
init_timers
.../broadcom-wl-5.10.56.27.3/driver/wl_linux.c:2577:10: error:
'struct timer_list' has no member named 'data'
t->timer.data = (ulong) t;
^
.../broadcom-wl-5.10.56.27.3/driver/wl_linux.c:2578:20: error: assignment
to 'void (*)(struct timer_list *)' from incompatible pointer type
'void (*)(ulong)' {aka 'void (*)(long unsigned int)'}
[-Werror=incompatible-pointer-types]
t->timer.function = wl_timer;
This should fix build of several devices on bcm63xx with testing
kernel (4.19).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"Whoop whoop, sound of da police"
Add an ingress capable traffic policer module configurable with tc.
From the man page:
The police action allows to limit bandwidth of traffic matched by the
filter it is attached to. Basically there are two different algorithms
available to measure the packet rate: The first one uses an internal
dual token bucket and is configured using the rate, burst, mtu,
peakrate, overhead and linklayer parameters. The second one uses an
in-kernel sampling mechanism. It can be fine-tuned using the estimator
filter parameter.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
IPv6 modules should all depend on @IPV6, to avoid circular dependencies
problems, especially if they select a module that depends on IPV6 as
well. In theory, if a package A depends on IPV6, any package doing
'select A' (DEPENDS+= A) should also depend on IPV6; otherwise selecting
A will fail. Sometimes the build system is forgiving this, but
eventually, and unexpectedly, it may blow up on some other commit.
Alternatively one can conditionally add IPv6 dependencies only if
CONFIG_IPV6 is selected: (DEPENDS+= +IPV6:package6).
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This commit add patch with 14c3:7610 pci id addition.
It was sent upstream.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[bumped PKG_RELEASE]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The mlk5 kmod lacks all necessary build symbols
for kernel 4.14 (again).
Add missing symbols to avoid build failure on these targets.
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[rewrite commit message - reorder symbols]
Signed-off-by: David Bauer <mail@david-bauer.net>
Missing config symbols could lead to build failures on kernel
4.14/4.19.
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[rephrase commit message - reorder symbols]
Signed-off-by: David Bauer <mail@david-bauer.net>
add module to support Mellanox Connect-X card
mlx4 supports ConnectX-3 series and previous cards
mlx5 supports Connect-IB/ConnectX-4 series and later cards
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Use in tree version of cake for kernels 4.19+ and backport features from
later kernel versions to 4.19.
Unfortunately PROVIDES dependency handling produces bogus circular
dependency warnings so whilst this package and kmod-sched-cake-oot
should be able to PROVIDE kmod-sched-cake this doesn't work.
Instead, remove the PROVIDES option and modify package sqm-scripts to
depend on the correct module independently.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
In preparation for dropping the out of tree cake module and using
in tree cake from upstream, rename the package to kmod-sched-cake-oot
(out of tree)
Initially add a PROVIDES kmod-sched-cake so that package dependencies
can be satisfied.
Ultimately this package will be removed when linux 4.14 is removed.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The calibration patches for MT7620 unnecessarily export symbols and
populate never accessed function pointers. Remove all that and make
functions static as the only place where each of those functions is
called is within rt2800lib.c.
Also make code more readable by fixing indentation, removing
unnecessary parantheses and simplifying some instructions using
shorthands here and there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Commit ea50780 backported Airtime Queue Limits (AQL) from Linux 5.5
to OpenWrt's backports 5.4. However, this only enabled AQL for the
vanilla ath10k driver. This patch also enables it for ath10k-ct.
Tested on:
* 2xTP-Link Archer A7v5 (QCA9563/QCA988X)
* Backports version 5.4-rc8 & 5.4.27
* ath10k-ct and ath10k-ct-htt firmware version 014 to 017
* ath10k-ct driver versions dc025dc to 3d173a4 (CT_KVER-5.4)
* WPA2, 802.11krv
Tested since January 25, 2020.
Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
Do not export static functions, they are anyway not referenced by any
code in a different module.
This fixes the following compile warning:
WARNING: "rt2800_rf_aux_tx0_loopback" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_write_dc" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_rf_configstore" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_do_sqrt_accumulation" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_rf_configrecover" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_loft_search" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_iq_search" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_setbbptonegenerator" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_rf_aux_tx1_loopback" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Building of ath79-tiny has uncovered following:
Package kmod-rtl8723bs is missing dependencies for the following libraries:
mmc_core.ko
So add this missing dependency.
Fixes: 8c26d67a67 ("mac80211: realtek: add staging driver for RTL8723BS SDIO module")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
the code would unconditionally tear down all interfaces upon a reconf.
This should only be done when the reconf call fails.
Signed-off-by: John Crispin <john@phrozen.org>
This patch backports the hwmon drivetemp sensor module from vanilla
linux 5.5 to be available on OpenWrt's 5.4 kernel.
Extract from The upstream commit by Guenter Roeck <linux@roeck-us.net>:
hwmon: Driver for disk and solid state drives with temperature sensors
"Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.
This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.
With this driver, the hard disk temperature can be read [...]
using sysfs:
$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000
If the drive supports SCT transport and reports temperature limits,
those are reported as well.
drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1: +27.0<C2><B0>C (low = +0.0<C2><B0>C, high = +60.0<C2><B0>C)
(crit low = -41.0<C2><B0>C, crit = +85.0<C2><B0>C)
(lowest = +23.0<C2><B0>C, highest = +34.0<C2><B0>C)
The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism."
This patch incorperates a patch made by Linus Walleij:
820-libata-Assign-OF-node-to-the-SCSI-device.patch
This patch is necessary in order to wire-up the drivetemp
sensor into the device tree's thermal-zones.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This external switch driver should be loaded on boot for network support
in failsafe mode.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[alter commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
For virtual access points (when multiple SSIDs are used for one
physical AP), there exist one physical network interface and
multiple virtual interfaces, which are fully under control of
hostapd. When networking is setup, the script
`/lib/netifd/wireless/mac80211.sh` is called, which tries to bring
the interface up by a call to `ip link set dev <iface> up`. This
call might fail for virtual APs, because the virtual interface
might not have been created by hostapd yet. There are some artifical
delays in the script most probably to handle this, but when DFS
channel availability check on 5GHz band is issued, hostapd can
delay creating virtual interfaces by a minute.
In order to fix this (or work around it), do not try to bring the
interface up (this is responsibility of hostapd anyway) and
do not try to set txpower on the virtual interface.
Fixes FS#2698.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Compiling the ltq-tapi driver against Linux 5.4 results in a compile
error complaining that the size of struct sched_param is not known.
Switch the existing "sched/types.h" include to reference
include/uapi/linux/sched/types.h to fix compilation against Linux 5.4.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Upstream commit 84ede58dfcd1d ("crypto: hash - remove
CRYPTO_ALG_TYPE_DIGEST") drops the CRYPTO_ALG_TYPE_DIGEST define because
it has the same value as CRYPTO_ALG_TYPE_HASH. This was the case for
earlier kernels as well. Switch to CRYPTO_ALG_TYPE_HASH to fix building
against Linux 5.4.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Upstream commit e4b92b108c6cd6 ("timekeeping: remove obsolete time
accessors") removed do_gettimeofday(). In Linux 4.19 this was only a
wrapper around ktime_get_real_ts64(). Use ktime_get_real_ts64() now that
the wrapper is gone to fix compilation against Linux 5.4.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Upstream commit e4b92b108c6cd6 ("timekeeping: remove obsolete time
accessors") removed do_gettimeofday(). In Linux 4.19 this was only a
wrapper around ktime_get_real_ts64(). Use ktime_get_real_ts64() now that
the wrapper is gone to fix compilation against Linux 5.4.
Move the ifxmips_mei_interface header to the include directory, it can't
be found otherwise during compilation. The reason for the changed
behaviour is not yet clear, however having header files in an include
directory is more straight forward.
To use the of_device_id struct, the mod_devicetable header need to be
included. Instead of including this header, include the of_platform
header, which includes the mod_devicetable on its own.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Upstream commit 96d4f267e40f95 ("Remove 'type' argument from access_ok()
function") removes the first argument to access_ok.
Adjust the code so it builds with Linux 5.4.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Beginning with linux 5.3, kmod-serial-8250 uses functions provided by
serial_mctrl_gpio.ko if GPIO support is enabled.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Currently kmod-i2c-mux-* will not get into images unless kmod-i2c-mux is added
to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-i2c-mux-pca954x
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently kmod-i2c-* will not get into images unless kmod-i2c-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-lm75
- kmod-i2c-gpio
- kmod-i2c-gpio-custom
- kmod-i2c-mux
- kmod-i2c-ralink
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently kmod-hwmon-* will not get into images unless kmod-hwmon-core is added
to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-gpiofan
- kmod-hwmon-lm63
- kmod-hwmon-lm75
- kmod-hwmon-lm85
- kmod-hwmon-lm90
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, adjust line wrapping]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
By default on module load, 2 ifb interfaces are created and typically
remain unused, cluttering 'ip link' outputs and generally confusing
things. sqm-scripts for example, creates its own ifb interface/s
instead of using these 2 defaults ifbs.
Tell the ifb module to not create any default ifbs on load via the
numifbs parameter.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Currently kmod-ata-* will not get into images unless kmod-ata-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-ata-ahci
- kmod-ata-ahci-mtk
- kmod-ata-sunxi
While at it, use AddDepends/ata for kmod-ata-pdc202xx-old.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This was available since kernel 5.4. The one provided in packages feed
will be considered deprecated and renamed to kmod-fs-exfat0.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(use name kmod-fs-exfat. use "@!(LINUX_4_4||LINUX_4_19)" for dependency)
Removes one of the duplicate `gpio-keys` words found in the logs:
gpio-keys gpio-keys: gpio-keysdoes not support key code:143
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Adds into 4.19 backported kernel module from 5.1 for Sensirion SPS30
particulate matter sensor, for kernel 5.4 backported dependency fix.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Otherwise we would need to enable IIO_TRIGGERED_BUFFER symbol in all
kernels in order to be able to use any of the IIO modules which are
utilizing triggered buffer based data acquisition method.
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
On platforms that do not have CONFIG_MTD enabled, loading the
rt2x00lib kernel module fails because it depends on symbols from
the mtd module ("Unknown symbol get_mtd_device_nm").
This commit disables the code that can read the eeprom from mtd if
mtd is not enabled.
Signed-off-by: Sven Over <sp@cedenti.st>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Since now we support both kernel 4.19 and 5.2, change the
condition to remove driver when on kernel 4.14
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Fixes following build error on mpc85xx/p2020:
Package kmod-iio-st_accel is missing dependencies for the following libraries:
regmap-core.ko
Fixes: 2d8f4c4fbd ("kernel: iio: add st-accel driver modules")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Adds kernel modules for various STMicroelectronics accelerometers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[added missing commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch fixes the regression caused by adding the NEON
variant of the ghash as the default ghash package package:
> ERROR: module '[...]/arch/arm/crypto/ghash-arm-ce.ko' is missing.
> modules/crypto.mk:286: recipe for target
> '[...]/kmod-crypto-ghash_4.19.106-1_aarch64_cortex-a53.ipk' failed
This patch limits the scope to the ARM32/cortexa9 target of mvebu.
Fixes: 285df63efc ("kernel: build neon-asm version of ghash module")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This builds the regular arm and arm-neon asm optmized modules for sha1
and sha512, for targets that set CONFIG_ARM_CRYPTO.
On ip40xx, the arm-asm version of sha1 improves performance by 5% over
the generic C implementation; sha1-neon is 25% faster than generic,
and sha512-neon, 259%.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This alone improves AES-GCM performance by up to 50% on ipq40xx. This
is enabled for targets that support neon and set CONFIG_ARM_CRYPTO:
imx6, ipq40xx, and mvebu.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The nvmem framework is now used in net/ethernet/eth.c and the nvmem
sysfs is split into a separate Kconfig option. More work would be needed
to adapt this patch for the broader use. The current patch compiles fine
on ath79, but it breaks the x86 target.
nvmem is also compiled into the kernel for most of our targets for
example ath79 anyway, so patching the kernel to remove it is now harder
and not the case on multiple targets anyway. Instead of making this work
on kernel 5.4 just remove this hack patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This module was added with kernel 4.15, but is was removed again with
kernel version 5.3. OpenWrt does not support specifying a kernel version
range so just break it with kernel 4.14 and only support recent kernel
versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With kernel 5.4 kmod-sound-hda-intel also needs snd-intel-nhlt.ko, but
this kernel module is only build on x86, make the OpenWrt kmod depend on
TARGET_x86.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
nf_reset() was renamed to nf_reset_ct() in upstream Linux commit
895b5c9f206e ("netfilter: drop bridge nf reset from nf_reset)"
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
gigaset was moved to staging in kernel 5.4, just deactivate it on
recent kernel versions instead of adapting it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 5.3 and 5.4 some crypto modules were split into two modules,
one implementing the crypto algorithm and the other integrating it
into the Linux crypto framework.
Adapt OpenWrt to support this split.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the new xfrm4_mode_beet, xfrm4_mode_transport,
xfrm4_mode_tunnel and their IPv6 versions on kernel 5.4. These modules
were newly added in kernel 5.2.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
ath10k-ct supports the combination to select IBSS (ADHOC) mode and
different beacon intervals together. mac80211 does not like this
combination, but Ben says this is ok, so remove this check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
As 07e1d88d7b ("kernel: avoid underscore in *6lowpan package names") shows,
underscores might cause build failures. Replace underscore with dash.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The SUBDIRS variable has been removed in kernel 5.4, and was deprecated
since the beginnig of kernel git history in favour of M or KBUILD_EXTMOD.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
f4415afce213 mt76: mt76u: loop over all possible rx queues in mt76u_rx_tasklet
5b9f949cb760 mt76: mt76u: fix a possible memory leak in mt76u_init
fd892bc033fb mt76: mt76u: rely only on data buffer for usb control messagges
Signed-off-by: Felix Fietkau <nbd@nbd.name>
bd0df1b017a8 mt76: avoid extra RCU synchronization on station removal
d5a5e97b67c7 mt76: mt76x2: avoid starting the MAC too early
a67e42990d8a mt76: mt7615: fix msdu_id endianness in mt7615_write_hw_txp
d3af8bd3c722 mt76: mt7615: set proper length in strncmp
9c43417db17c mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
764e1d208a06 mt76: mt7615: fix tx power reporting
1881241c7ee5 mt76: fix rounding issues on converting per-chain and combined txpower
fa14e7f33199 mt76: mt7615: rework rx phy index handling
a205ce3e3e2d mt76: mt7615: fix ext_phy flag for stations
457a93203690 mt76: mt7615: fix MT_TX_HW_QUEUE_EXT_PHY to deal with mac80211 changes
c75cf513c674 mt76: do not set HOST_BROADCAST_PS_BUFFERING for mt7615
cc56c400167c mt76: fix LED link time failure
4dbd56b86970 mt76: mt76x0u: add support to TP-Link T2UHP
e226309c4bc4 mt76: mt7615: rely on mt76_queues_read for mt7622
c6a025318075 mt76: mt76u: extend RX scatter gather number
dfc24bc504e3 mt76: mt76u: rename stat_wq in wq
2bbffd2cb37b mt76: mt7615: remove rx_mask in mt7615_eeprom_parse_hw_cap
f408a2b7566c mt76: Introduce mt76_mcu data structure
17ecf0762542 mt76: mt76x02: fix handling MCU timeouts during hw restart
284e9fd72912 mt76: mt7615: fix monitor injection of beacon frames
8f8e9161b355 mt76: fix array overflow on receiving too many fragments for a packet
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Packages kmod-bluetooth_6lowpan and kmod-ieee802154_6lowpan contain an
underscore in the package name. This causes problems in package/install
because when building a list of package files to install offline using
opkg, it uses a wildcard of the form $(dir)/$(pkg)_*.ipk.
If you were to select kmod-bluetooth=y, but kmod-bluetooth_6lowpan=m,
the latter would be picked up by that wildcard, and make package/install
would fail:
Collected errors:
* satisfy_dependencies_for: Cannot satisfy the following dependencies
* for kmod-bluetooth_6lowpan:
* kmod-6lowpan
* opkg_install_cmd: Cannot install package kmod-bluetooth_6lowpan.
Changing the wildcard pattern is not trivial, and there may be other
places in the build system making this assumption about the package name
format.
Using a dash in place of the underscore avoids the issue.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Despite, since subtargets range from bcm2708 to bcm2711, it seems
appropriate to use bcm27xx instead of bcm2708 (again, as already done
for BOARDNAME).
This also renames the packages brcm2708-userland and brcm2708-gpu-fw.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Changes:
ath10k-ct: Support better RSSI measurements.
When used with recent firmware, these changes allow the driver to
query per-chain noise-floor from the radio to better calculate the
per-chain RSSI. The per-chain RSSI is then summed to provide the
'combined RSSI'. This gives better per-chain RSSI as well as combined
RSSI, especially when running with more than 20Mhz bandwidths.
Refresh patches.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq806x+qca9984,ipq4019+qca9986]
Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
Most of the broadcom packaging codes were moved to broadcom.mk in commit
7f984dab1c ("mac80211: move broadcom packaging code to broadcom.mk"),
but b43/install still remained. Move it now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Package kernel module for Linear Technology MCP3021/3221 I2C connected
current and voltage monitor chips.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It is generally more desirable to use older kernel versions for
dependencies, as this will require less changes when newer kernels
are added (they will by default select the newer packages).
Since we currently only have two kernels (4.14 and 4.19) in master,
this patch applies this logic by converting all LINUX_4_19 symbols
to their inverted LINUX_4_14 equivalents.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Call skb_orphan(skb) to call the owner's destructor function and make
the skb unowned.
This is necessary to prevent sk_wmem_alloc of a socket from overflowing,
which leads to ENOBUFS errors on application level.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
hostapd allows putting WDS (4addr mode) clients into a separate bridge
other than the bridge regular (3addr mode) clients end up in. This is
useful for example giving WDS clients access to several VLANs
(trunking) while regular clients will end up inside a specific VLAN.
Add 'wds_bridge' config parameter for wifi-iface which contains the
name of the bridge. hostapd-mini already supports this feature, so all
needed is to add the UCI wrapping in mac80211.sh.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for Methode DM7052 NBASE-T module to OpenWRT. These
patches are taken from my "phy" branch, and will be sent for the
next kernel merge window.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: move patches to pending, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Most of the kernel version switches below 4.14 were removed in commit
97940f8766 ("kernel: remove obsolete kernel version switches"),
but some of them still remained. Remove them now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This patch adds 'qca,gpio-mask=<u32>' device tree property to ath9k node.
This optional setting is a hack and should only be used in very special
(and rare) cases when a button or LED is wired to a GPIO pin normally
masked out (due to being one-way etc). Netgear WNDR4300 v2 is one such
example - it uses GPI9 for RFKILL.
See ath9k/reg.h *_GPIO_MASK constants.
Use with caution and expect to see stream of kernel warnings if wrong
mask value is provided.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
The 'DEFAULT:=m if ALL' line prevents the phase1 buildbots from building
the package, and users from downloading it, since they use 'ALL_KMODS=y'
but 'ALL' is not set.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Network interfaces are looked up based on the device behind a phy, so the
phy needs to be checked separately
Signed-off-by: Felix Fietkau <nbd@nbd.name>
After kernel 4.9 has been removed, this removes all (now obsolete)
kernel version switches that deal with versions before 4.14.
Package kmod-crypto-iv is empty now and thus removed entirely.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Keep up with a small amount of churn in the upstream repository.
Upstream now represents the version of CAKE as found in the linux kernel
from 4.19 onwards but with some compatibility stubs to allow building on
<4.19.
After a diversion related to an experimental ECN implementation which
has now been reverted, the important and relevant changes for us are:
8a8946b sch_cake: avoid possible divide by zero in cake_enqueue()
183b320 RFC 8622 diffserv3, 4 & 8 LE PHB support
6ff4561 sch_cake: Make sure we can write the IP header before changing DSCP bits
9fba602 sch_cake: Use tc_skb_protocol for getting packet protocol
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This target is still on kernel 4.9, and it looks like there is no
active maintainer for this target anymore.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target seems to have been unmaintained for quite a while, and not a
single tester for the (now outdated) kernel 4.14 patches has been found.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
This patch is build-tested only, but has never been device-tested. It is
only added to preserve the changes in Git history prior to removing this
target. Use it with care.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[rebased and extended commit message, refreshed patches for 4.14.162]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These two hacks are no longer necessary as they've
been moved to a special variant of kmod-ath10k-ct.
So, if you have a device suffering from low-memory
situation and getting applications crashes due to
the OOM reaper or kernel panics with ath10k, please
use the "kmod-ath10k-ct-smallbuffers" package from
now on.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds a (currently missing) throughput LED trigger for the rt2x00
driver. Previously, LED triggers had to be assigned to the netdev, which
was limited to a single VAP.
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Christoph Krapp <achterin@googlemail.com>
2a0a19168dce mt7603: remove vif sta from poll list on interface remove
dc14ac64e7f3 mt7615: remove vif sta from poll list on interface remove
d868638fdd96 mt76: remove obsolete .add_buf() from struct mt76_queue_ops
50b1e9bd25cd mt76: refactor cc_lock locking scheme
1987b741dac2 mt76: mt76x0: remove 350ms delay in mt76x0_phy_calibrate
c93a2d1c1304 mt76: mt76x02u: update ewma pkt len in mt76x02u_tx_prepare_skb
58e1e969f03e mt76: mt7615: remove unneeded semicolon
c14d6563c492 mt76: mt76x2e: disable pcie_aspm by default
f2be00b1011a mt76: dma: fix buffer unmap with non-linear skbs
20f05897873a mt76: mt76u: rely on usb_interface instead of usb_dev
3cbaf81a185e mt76: mt76u: rely on a dedicated stats workqueue
ea19cd7ac6c6 mt76: Remove set but not used variable 'idx'
a85c06cec844 mt76: use mt76_dev in mt76_is_{mmio,usb}
e0731a82a14f mt76: move SUPPORTS_REORDERING_BUFFER hw property in mt76_register_device
cfdb75124e7c mt76: mt7615: add ibss support
e2f90adcc3b1 mt76: move interface_modes definition in mt76_core module
5dfb0ec9c6d1 mt76: mt7615: disable radar pattern detector during scanning
7121e163c068 mt76: fix possible out-of-bound access in mt7615_fill_txs/mt7603_fill_txs
db78ee08d95e mt76: move mt76_get_antenna in mt76_core module
faf5e6fedd7e mt76: mt7615: read {tx,rx} mask from eeprom
44825e88a42d mt76: use rcu_read_lock_bh in mt76_dma_rx_poll
af83ee8de928 mt76: move initialization of some struct members to mt76_alloc_device
6493e234b40d mt76: introduce struct mt76_phy
ea46624355ec mt76: add support for an extra wiphy in the rx path
c5f1e83e30d4 mt76: add support for an extra wiphy in the main tx path
1d8011871458 mt76: add support for an extra wiphy in the tx status path
e5e755a7a6b0 mt76: add support for an extra wiphy in mt76_sta_state()
ee36c8e2170f mt76: move channel state to struct mt76_phy
d246beb23350 mt76: keep a set of software tx queues per phy
a3e88bcf17e8 mt76: move state from struct mt76_dev to mt76_phy
9cda51d195db mt76: move chainmask back to driver specific structs
df74d6993383 mt76: move txpower_conf back to driver specific structs
9e95fa6208a2 mt76: move txpower and antenna mask to struct mt76_phy
502d09a6e806 mt76: add multiple wiphy support to mt76_get_min_avg_rssi
842cae558b82 mt76: add priv pointer to struct mt76_phy
8ca04846857b mt76: add function for allocating an external wiphy
04cd17a64520 mt76: add ext_phy field to struct mt76_wcid
1c8d69e7d666 mt76: move ampdu_ref from mt76_dev to driver struct
e6659d12d01e mt76: mt7615: add dual-phy support for mac80211 ops
e5ea72ac7158 mt76: mt7615: add multiple wiphy support for smart carrier sense
bdcd45dd04e0 mt76: mt7615: add missing register init for dual-wiphy support
0954c37d015f mt76: mt7615: remove useless MT_HW_RDD0/1 enum
705a0fcdc3a5 mt76: mt7615: add multiple wiphy support to the dfs support code
849fefacc48a mt76: mt7615: rework chainmask handling
caa47af1d6f2 mt76: mt7615: add multiple wiphy support to the rx path
c5585a735864 mt76: mt7615: initialize dbdc settings on interface add
6265fd1954d7 mt76: mt7615: move radio/mac initialization to .start/stop callbacks
5725d1f919ff mt76: mt7615: select the correct tx queue for frames sent to the second phy
993683d62fb7 mt76: mt7615: add support for registering a second wiphy via debugfs
1456a53ddeb3 mt76: mt7615: update beacon contents on BSS_CHANGED_BEACON
ea41ad8bdb36 mt76: mt7615: defer mcu initialization via workqueue
59de6c9447a7 mt7615: replace sta_state callback with sta_add/sta_remove
88db676f8517 mt76: fix rx dma ring descriptor state on reset
fff2c07193bb Revert "mt76: use rcu_read_lock_bh in mt76_dma_rx_poll"
b3bf83d6da1c mt76: disable bh in mt76_dma_rx_poll
efcbee1d8bfc mt76: mt76x0u: do not reset radio on resume
5dc6f6fcc027 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 174
84554a1fbb9a kernel: fix typos and some coding style in comments
a116b0a6afe9 mt76: fix possible undetected invalid MAC address
becdec318fce mt76: Off by one in mt76_calc_rx_airtime()
683eb244fa55 mt76: mt7603: reset STA_CCA counter setting the channel
812692db171c mt76: eeprom: add support for big endian eeprom partition
8b362382b10c mt76: mt7615: Fix build with older compilers
fc24815a2cb4 mt76: mt7615: report firmware version using ethtool
5cec93d57e6d mt76: mt76x02: fix coverage_class type
9354f0f41d1c mt76: mt7603: set 0 as min coverage_class value
a589d095eeb6 mt76: mt7615: add set_coverage class support
257c19f5b56f mt76: clear skb pointers from rx aggregation reorder buffer during cleanup
05c87a33831f mt76: do not overwrite max_tx_fragments if it has been set
05fa07c667f3 mt76: use AC specific reorder timeout
3ef5f3444a94 mt76: mt7615: measure channel noise and report it via survey
726fd501651a mt76: mt7615: increase MCU command timeout
99d8cd03edfa mt76: mt7603: fix input validation issues for powersave-filtered frames
32129af2604d net/wireless: Delete unnecessary checks before the macro call “dev_kfree_skb”
85a8abf80385 mt76: mt76x02: omit beacon slot clearing
8b5d3615e1c8 mt76: mt76x02: split beaconing
dc364547d91a mt76: mt76x02: add check for invalid vif idx
462a16e185e4 mt76: mt76x02: remove a copy call for usb speedup
fa24aba4c280 mt76: speed up usb bulk copy
6a84ad21306e mt76: mt76x02: add channel switch support for usb interfaces
09fcbc214b10 mt76: usb: use max packet length for m76u_copy
584c0784e019 mt76: mt76x02u: do not set NULL beacons
ca17e5657e8a mt76: mt76x02: minor mt76x02_mac_set_beacon optimization
d5fdd2e7ced8 mt76: mt7615: fix MT7615_CFEND_RATE_DEFAULT value
ae25a4bf99a9 mt76: mt7615: introduce LED support
cd759b00cc06 mt76: mt76x02: simplify led reg definitions
cf00467c5de4 mt76: mt7603: simplify led reg definitions
1c8e76f4de3e mt76: fix compilation warning in mt76_eeprom_override()
960f5cc2390b mt76: mt76u: fix endpoint definition order
15e1c29ed8e3 mt76: mt7615: add missing settings for simultaneous dual-band support
e09b9f61eeb3 mt76: mt7615: rework set_channel function
4cb1195a1530 mt76: mt7615: add set_antenna callback
Signed-off-by: Felix Fietkau <nbd@nbd.name>
According to many bugreports [0][1][2] the default ath10k-ct kernel
module is unusable on devices with just 64 MiB RAM or with 128 MiB and
dual ath10k cards. The target boards boot but eventually oom-killer
starts to interfere with normal operation, so the current state is
effectively broken.
Since the two patches in question have a performance impact (and
possibly some other unexpected side-effects) a dedicated build variant
is added so that users of the low RAM devices can still benefit from all
the ath10k-ct advantages.
According to testing [3] results, the issue can be experienced even with
"a 256MB device with three radios". Measured performance impact of
implementing small buffers was lowering "the maximum 5 GHz throughput on
an IPQ40xx device without RPS/XPS optimizations from 494/432 Mbit/s for
TCP transfers (download/upload) to 438/343 Mbit/s"
The patches were apparently inspired by QSDK tweaks used by ODMs for the
affected devices.
[0] http://lists.infradead.org/pipermail/openwrt-devel/2019-December/020573.html
[1] https://github.com/openwrt/openwrt/pull/1077
[2] https://bugs.openwrt.org/index.php?do=details&task_id=2664
[3] https://github.com/freifunk-gluon/gluon/pull/1440#issue-195607701
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[Remove double CONFIG_ATH10K-CT_LEDS entry]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Unloading and reloading the modules fails, as platform_device_put() does not
release resources fully.
root@OpenWrt:/# insmod i2c-gpio-custom bus0=0,18,0,5
[ 196.860620] Custom GPIO-based I2C driver version 0.1.1
[ 196.871162] ------------[ cut here ]------------
[ 196.880517] WARNING: CPU: 0 PID: 1365 at fs/sysfs/dir.c:31 0x80112158
[ 196.893431] sysfs: cannot create duplicate filename '/devices/platform/i2c-gpio.0'
...
[ 197.513200] kobject_add_internal failed for i2c-gpio.0 with -EEXIST, don't try to register things with the same name in the same directory.
This patch fixes it by replacing platform_device_put() to
platform_device_unregister().
Fixes: da77408537 ("i2c-gpio-custom: minor bugfix")
Fixes: 3bc81edc70 ("package: fix w1-gpio-custom package (closes#6770)")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
- usb-dwc3-of-simple is not used anymore as we have qcom dedicated driver
- usb-phy-qcom-dwc3 is not dependent of dwc3-of-simple
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This update doesn't include:
3b1e0a7bdfee brcmfmac: add support for SAE authentication offload
be898fed355e brcmfmac: send port authorized event for FT-802.1X
due to nl80211 dependencies.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
With this patch, txpower for the PHY is applied when configuring the PHY
instead of the VIF. Otherwise, the configured txpower is not applied for
the first initialized VIF when using DFS channels, as it is currently
applied too early when the CAC hasn't finished.
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
If no AP is configured, hostapd-${phy}.conf is not being created,
hence md5sum fails and causes log pollution:
netifd: radio1 (3183): md5sum: can't open '/var/run/hostapd-phy1.conf': No such file or directoy
Hence make sure the file exists when calling md5sum.
Fixes: a5bc9787d4 ("mac80211: add support for dynamically reconfiguring wifi")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Before commit 60fb4c92b6 ("hostapd: add ubus reload") netifd was
tracking hostapd/wpa_supplicant and restarting wifi in case of a
process crash. Restore this behaviour by tracking the PIDs of
hostapd and wpa_supplicant.
Also make sure hostapd and/or wpa_supplicant have been started before
emmitting ubus calls to them using ubus wait_for.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In addition to wpa_supplicant and hostapd managed interfaces, also
track unmanaged interfaces. This is used to make sure that running
'wifi' always returns into a clean state regardless of what the user
did before.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Owl Loader (named after the codename that Atheros gave
these devices back in the day) has been accepted upstream.
This patch removes the "misc" driver OpenWrt had and adds
the remaining differences against the version that ships
with 5.4-rc1 into a separate "120-owl-loader-compat.patch"
file that can be cut down once AR71XX is being dealt with.
Note: I decided to keep the existing (kmod-)owl-loader
package name around for now. The kernel module file in
the kmod package will be called ath9k_pci_owl_loader.ko
though.
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This reverts commit 8176431963 ("mt76: probe load mt7615 driver
asynchronously"). After said commit, users report that MT7615 no longer
works on boot and they have to manually enable WiFi (via command "wifi") to
make it working again.
Fixes: FS#2546
Ref: https://forum.openwrt.org/t/xiaomi-r3p-no-wifi-on-boot/45509
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This also fixes mac80211_prepare_vif iw set channel in monitor or
mesh mode.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: fixed commit message]
Commit b3d8b3a introduced a new test:
[ -n "$noscan" -a "$noscan" -gt 0 ] && hostapd_noscan=1
But if length of "$noscan" is zero (noscan is not set) this doesn't stop
the shell to evaluate the rest of the test.
root@hank2:~# [ -n "$noscan" -a "$noscan" -gt 0 ]
ash: out of range
root@hank2:~#
So when radios are brought up this shows in the log:
Sat Nov 23 10:51:38 2019 daemon.info procd: - init complete -
Sat Nov 23 10:52:24 2019 daemon.notice netifd: radio1 (1243): sh: out of range
Sat Nov 23 10:52:25 2019 user.notice firewall: Reloading firewall due to ifup of wan (eth0.2)
Sat Nov 23 10:52:25 2019 daemon.notice netifd: radio0 (1242): sh: out of range
Sat Nov 23 10:52:26 2019 authpriv.info dropbear[1536]: Not backgrounding
This commit sets noscan to 0 if unset and removes the gratuitous length
check, preventing the warning.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
This updates mac80211 to backports based on kernel 5.4-rc8.
The deleted patches were applied upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This potentially fixes some issues seen on IBSS
when interfaces go out of range and then re-appear.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The skb_get_hash_perturb() function now takes a siphash_key_t instead of
an u32. This was changed in commit 55667441c84f ("net/flow_dissector:
switch to siphash"). Use the correct type in the fq header file
depending on the kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Keep existing wdev when creating new nl80211 interfaces if phy and
type match, delete it otherwise.
To make this work, also remove left-over debugging function which
prevented the return-value of the 'iw' command to be taken into
account in mac80211_iw_interface_add().
As 4addr-mode (WDS) was setup during interface creation for station
interfaces, also set it after interface creation to make sure an
existing sta interface ends up with the right mode.
Fixes: a5bc9787d4 ("mac80211: add support for dynamically
reconfiguring wifi")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
AutoLoad parameter must match the exact kernel module name. Fix it.
Fixes: 125f1ce9ad ("kernel: video: add DRM core and IMX DRM support for HDMI/LVDS")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Changes introduced for dynamic wifi reconfiguration left behind
unmanaged interface types. Restore parts of the old function to
also clean (unencrypted, non-DFS) mesh and ad-hoc interfaces.
Fixes: a5bc9787d4 ("mac80211: add support for dynamically
reconfiguring wifi")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Change scripts to use ubus interface of hostapd/wpa_supplicant to
add/remove/modify wireless interfaces instead of (re-)starting the
services.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of depending on kmod-usb2 make it depend on the normal USB
dependencies. This should hopefully fix some problems seen in the build
bot builds for powerpc_8540.
In addition also activate DRIVER_11N_SUPPORT support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is needed to export crypto information to netfilter, allowing
the alt. afalg openssl engine to obtain information about the drivers
being used.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The QCA953x only supports 25 MHz refclk, however some OEMs set an
invalid bootstrap value for the REF_CLK option, which would break the
clock detection in ath9k.
Force the QCA953x refclk to 25MHz in ath9k, as this is (according to the
datasheet) the only valid frequency.
Signed-off-by: David Bauer <mail@david-bauer.net>
The device path will be the same for the first phy. For all subsequent
phys, the path gets an extra +1, +2, ...
Move the code for converting path to phy and vice versa to a separate
library script shared by config detection code and the netifd wireless
handler script
Signed-off-by: Felix Fietkau <nbd@nbd.name>
https://patchwork.kernel.org/patch/11224189/
--
On 2019-10-28 06:07, wbob wrote:
> Hello Roman,
>
> while reading around drivers/net/wireless/ralink/rt2x00/rt2800lib.c
> I stumbled on what I think is an edit of yours made in error in march
> 2017:
>
> https://github.com/torvalds/linux/commit/41977e86#diff-dae5dc10da180f3b055809a48118e18aR5281
>
> RT6352 in line 5281 should not have been introduced as the "else if"
> below line 5291 can then not take effect for a RT6352 device. Another
> possibility is for line 5291 to be not for RT6352, but this seems
> very unlikely. Are you able to clarify still after this substantial time?
>
> 5277: static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
> ...
> 5279: } else if (rt2x00_rt(rt2x00dev, RT5390) ||
> 5280: rt2x00_rt(rt2x00dev, RT5392) ||
> 5281: rt2x00_rt(rt2x00dev, RT6352)) {
> ...
> 5291: } else if (rt2x00_rt(rt2x00dev, RT6352)) {
> ...
Hence remove errornous line 5281 to make the driver actually
execute the correct initialization routine for MT7620 chips.
As it was requested by Stanislaw Gruszka remove setting values of
MIMO_PS_CFG and TX_PIN_CFG. MIMO_PS_CFG is responsible for MIMO
power-safe mode (which is disabled), hence we can drop setting it.
TX_PIN_CFG is set correctly in other functions, and as setting this
value breaks some devices, rather don't set it here during init, but
only modify it later on.
Fixes: 41977e86c984 ("rt2x00: add support for MT7620")
Reported-by: wbob <wbob@jify.de>
Reported-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
--
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When ASLR_PIE was activated globally these drivers failed to build
because the user space LDFLAGS leaked into the kernel build process.
This was fixed in upstream Linux kernel commit ce99d0bf312d ("kbuild:
clear LDFLAGS in the top Makefile") which went into Linux 4.17. The
lantiq target is now on Linux 4.19 only and these exceptions are not
needed any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kconfig symbol is an invisible one since its introduction. It is
not supposed to be enabled on its own.
Resolves FS#1821
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This commit fixes failing builds because of an incorrect configuration
for the kmod-rtw88 package.
RTW88_8822BE as well as RTW88_8822CE have to bes selected as "y" even
when building the driver as a module.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commits adds packaging for the new RTW88 driver from Realtek.
It supports the Realtek 8822BE/8822CE PCIe wireless chips.
For operation, the complementary firmware has to be loaded.
Signed-off-by: David Bauer <mail@david-bauer.net>
This updates mac80211 to backports based on kernel 5.4-rc2
ath10k-ct was updated to match the API changes and iw now uses the new
nl80211.h header file.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The destination buffer size `d_len` is passed to `lzma_inflate` as a
pointer. Therefore, it needs to be dereferenced to compare its content.
Signed-off-by: Christian Franke <nobody@nowhere.ws>
The channel can be selected automatically at run time by setting
channel=acs_survey or channel=0, both of which will enable the ACS survey
based algorithm in hostapd. If the option acs_exclude_dfs is set in the
hostpad config DFS channels from ACS are excluded on channel selection.
This commit will add the possibilty to exclude the dfs channel on ACS
survey.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This driver supports the Bosch Sensortec BME680 gas, humidity, pressure
and temperature sensor.
Tested I2C and SPI modes on a Raspberry Pi Zero W.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Upon writing to "remove" file, debugfs_remove_recursive() blocks while
holding rtnl_lock. This is because debugfs' file_ops callbacks are
executed in debugfs_use_file_*() context which prevents file removal.
Fix this by only flagging the device for removal and then do the cleanup
in file_ops.release callback which is executed out of that context.
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
Since v3.11, netdevice notification data are of type
"struct netdev_notifier_info". Handle it as such!
This should fix a critical bug in which devices are unable get released
because trelay does not release resources in response to UNREGISTER
event spamming the log with something like:
unregister_netdevice: waiting for eth0.1 to become free. Usage count = 1
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
crypto-arc4 move into a module with commit c3a78955f3,
fs-nfs-common-rpcsec compile error without arc4 support.
Ref: https://github.com/openwrt/packages/issues/9912
Fixes: c3a78955f3 ("kernel: move crypto-arc4 into a module")
Signed-off-by: Ruixi Zhou <zhouruixi@gmail.com>
Add missing dependencies to i2c-core and regmap-spi. These get activated
when these modules are build in this driver, which is the case when we
build all modules. This fixes the build on some targets. This was found
by the buildbot.
Fixes: 34e2526f9f ("kernel: add kmod-rtc-pcf2127")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
71c2ef0420b5 mt76: fix aggregation stop issue
5b02a078d4a7 mt76: add missing locking around ampdu action
7d8764d320cf mt76: avoid enabling interrupt if NAPI poll is still pending
d94cc81d3980 mt76: drop rcu read lock in mt76_rx_aggr_stop
c11a4ad06d9d mt76: mt76x0: eeprom: add support for MAC address from OF
01642d8bed33 mt76: mt76x02: fix use-after-free in tx status code handling airtime
391e1488f885 mt76: add sanity check for a-mpdu rx wcid index
d3a589586d1b mt76: fix a-mpdu boundary detection issue for airtime reporting
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In non-ETSI regulatory domains scan is blocked when operating channel
is a DFS channel. For ETSI, however, once DFS channel is marked as
available after the CAC, this channel will remain available (for some
time) even after leaving this channel.
Therefore a scan can be done without any impact on the availability
of the DFS channel as no new CAC is required after the scan.
Enable scan in mac80211 in these cases.
Signed-off-by: Aaron Komisar <aaron.komisar@tandemg.com>
Link: https://lore.kernel.org/r/1570024728-17284-1-git-send-email-aaron.komisar@tandemg.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
This backport fixes high latency (>100ms) on the WiFi link when using a
QCA988x Wave 1 radio. The ath10k-ct driver is not affected by this bug
from my testing, hence why it hasn't been discovered earlier.
Signed-off-by: David Bauer <mail@david-bauer.net>
https://patchwork.kernel.org/patch/11161981/
--
From: Stanislaw Gruszka <sgruszka@redhat.com>
Subject: [PATCH] rt2x00: initialize last_reset
Initialize last_reset variable to INITIAL_JIFFIES, otherwise it is not
possible to test H/W reset for first 5 minutes of system run.
Fixes: e403fa31ed71 ("rt2x00: add restart hw")
Reported-and-tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
--
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
add module to support Emulex OneConnect
common in 10Gbit SFP+ cards by Dell/HP/IBM
supports OneConnect OCe10xxx OCe11xxx OCe14xxx,
LightPulse LPe12xxx
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This makes brcmfmac use the same wiphy after PCIe reset to help user
space handle corner cases (e.g. firmware crash).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Update the ath10k-ct driver version to 5e8cd86f90dac966d12df6ece84ac41458d0e95f
to enable dynamic VLANs to work. Patches refreshed during the bump.
Signed-off-by: Robert Marko <robimarko@gmail.com>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
From: Stanislaw Gruszka <sgruszka@redhat.com>
This reverts commit 9ad3b55654455258a9463384edb40077439d879f.
As reported by Sergey:
"I got some problem after upgrade kernel to 5.2 version (debian testing
linux-image-5.2.0-2-amd64). 5Ghz client stopped to see AP.
Some tests with 1metre distance between client-AP: 2.4Ghz -22dBm, for
5Ghz - 53dBm !, for longer distance (8m + walls) 2.4 - 61dBm, 5Ghz not
visible."
It was identified that rx signal level degradation was caused by
9ad3b5565445 ("rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band").
So revert this commit.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Close cooperation with Lorenzo Bianconi resulted
in these patches which fix all remaining seen issues
when using dynack.
Fix link losses when:
- Late Ack's are not seen or not present
- switching from too low static coverage class to dynack on a live link
These are fixed by setting the Ack Timeout/Slottime to
the max possible value for the currently used channel width when
a new station has been discovered.
When traffic flows, dynack is able to adjust to optimal values
within a few packets received (typically < 1 second)
These changes have been thoroughly tested on ~60 offshore devices
all interconnected using mesh over IBSS and dynack enabled on all.
Distances between devices varied from <100m up to ~35km
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Update ath10k-ct to commit 9e5ab25027e0971fa24ccf93373324c08c4e992d
git log --pretty=oneline --abbrev-commit f0aa8130..9e5ab250
9e5ab25 ath10k-ct: Update to latest 5.2 upstream, support bigger mtu, 160Mhz
Created with the help of the make-package-update-commit.sh script
and refresh patches.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
To do not brake HW restart we should keep initialization vectors data.
I assumed that on start the data is already initialized to zeros, but
that not true on some scenarios and we should clear it. So add
additional flag to check if we are under HW restart and clear IV's
data if we are not.
Patch fixes AP mode regression.
Patch pending on linux-wireless and imported from patchwork.
Fixes: 0b2c42ced2 ("mac80211: Update to version 5.2-rc7")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes a bug introduced in backports from kernel 5.1 which makes
ath10k crash on QCA9984 when a station connects. The FW sends a airtime
report, but this station is not yet fully registered and a NULL pointer
is used.
Fixes: 0b2c42ced2 ("mac80211: Update to version 5.2-rc7")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds a vendor command policy which is enforced since mac80211 from
kernel 5.3
Fixes: 928e893a11 ("mac80211: Update to version 5.3-rc4-1")
Signed-off-by: Boris Krasnovskiy <boris.krasnovskiy@lairdtech.com>
The removed patches were applied upstream.
The type of the RT2X00_LIB_EEPROM config option was changed to bool,
because boolean is an invalid value and the new kconfig system
complained about this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85)
Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e)
Revert "ramips: add preliminary support for WIO ONE" (085141dc5b)
Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539)
Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d)
Revert "toolchain: add autoconf-lean" (fdb30eed03)
Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is already enabled as kernel built-in feature in mvebu target and
none other target will use it.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This changes the default PKG_BUILD_DIR to take BUILD_VARIANT into
account (if set), so that packages do not need to manually override
PKG_BUILD_DIR just to handle variants.
This also updates most base packages with variants to use the updated
default PKG_BUILD_DIR.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
This doesn't include 9ff8614a3dbe ("brcmfmac: use separate Kconfig file
for brcmfmac") due to a few conflicts with backports changes.
An important change is:
[PATCH 2/7] brcmfmac: change the order of things in brcmf_detach()
which fixes a rmmod crash in the brcmf_txfinalize().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
the ath10k-ct package ships multiple versions of the ath10k-ct driver,
OpenWrt currently only uses the version 4.19, but we still ship some
patches for older versions. Remove all patches only touching older
versions and also remove the patch for older versions from patches which
do the same changes to multiple versions of ath10k-ct.
This removes some unneeded patches, the end binary should stay the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates mac80211 to version 5.2-rc7, this contains all the changes
to the wireless subsystem up to Linux 5.2-rc7.
* The removed patches are applied upstream
* b43 now uses kmod-lib-cordic
* Update the nl80211.h file in iw to match backports version.
* Remove the two backports from kernel 4.9, they were needed for mt76,
but that can use the version from backports now, otherwise they
collide and cause compile errors.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
By default, set BE tx queue TXOP limit to 1.0 in the hostapd config
Many vendor drivers are doing similar things to boost throughput.
On MT7612 under ideal conditions, it improves tx throughput from 470 Mbit/s
to about 570 Mbit/s.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch unifies the polled and interrupt-driven gpio_keys code
paths as well implements consistent handling of the debounce
interval set for the GPIO buttons and switches.
Hotplug events will only be fired if
1. The input changes its state and remains stable for the duration
of the debounce interval (default is 5 ms).
2. In the initial stable (no state-change for duration of the
debounce interval) state once the driver module gets loaded.
Switch type inputs will always report their stable state.
Unpressed buttons will not trigger an event for the initial
stable state. Whereas pressed buttons will trigger an event.
This is consistent with upstream's gpio-key driver that uses
the input subsystem (and dont use autorepeat).
Prior to this patch, this was handled inconsistently for interrupt-based
an polled gpio-keys. Hence this patch unifies the shared logic into the
gpio_keys_handle_button() function and modify both implementations to
handle the initial state properly.
The changes described in 2. ) . can have an impact on the
failsafe trigger. Up until now, the script checked for button
state changes. On the down side, this allowed to trigger the
failsafe by releasing a held button at the right time. On the
plus side, the button's polarity setting didn't matter.
Now, the failsafe will only engage when a button was pressed
at the right moment (same as before), but now it can
theoretically also trigger when the button was pressed the
whole time the kernel booted and well into the fast-blinking
preinit phase. However, the chances that this can happen are
really small. This is because the gpio-button module is usually
up and ready even before the preinit state is entered. So, the
initial pressed button event gets lost and most devices behave
as before.
Bisectors: If this patch causes a device to permanently go into
failsafe or experience weird behavior due to inputs, please
check the following:
- the GPIO polarity setting for the button
- the software-debounce value
Run-tested for 'gpio-keys' and 'gpio-keys-polled' on
- devolo WiFi pro 1200e
- devolo WiFi pro 1750c
- devolo WiFi pro 1750x
- Netgear WNDR4700
- Meraki MR24
- RT-AC58U
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [further
cleanups, simplification and unification]
b43legacy needs ssb support and we do not compile the mips74 subtarget
of the brcm47xx target with SSB support. This causes a build failure in
the mac80211 package and only some of the kernel modules are being
created.
I am not aware of any device with a BRCM47xx mips74 CPU which uses a
b43legacy compatible device.
Fixes: FS#2334
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix file installation clash between kmod-sched & kmod-sched-cake as both
try to install sch_cake.ko
Remove cake from kmod-sched package as cake is supposed to be the
optional qdisc.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
CAKE made it to kernel 4.19 and since OpenWrt now at kernel 4.19 we can
drop the out of tree cake package in base repository.
Add kmod-sched-cake to netsupport so package dependencies are still met.
Similarly CAKE is retained as an optional qdisc module to avoid base
scheduler package size implications.
Backport upstream patches from k5.1 to address some small bugs and
support fwmark usage.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Linux 4.15 removes the init_timer() API. It's replaced by two functions:
- timer_setup() is used instead of init_timer() and also replaces the
timer "function" (callback) setup.
- from_timer() has to be used to obtain the use-case specific data from
a struct timer_list, which is now passed to the timer callback.
Update the timer API to be compatible with Linux 4.15+ so it compiles
with the upcoming Linux 4.19 kernel update.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
b3a2965 mt76x02: fix crash on device reset
ffddb68 mt76x02u: check chip version on probe
7fc5f92 mt76x2u: remove duplicated entry in mt76x2u_device_table
61311d9 mt76: introduce mt76_free_device routine
a7dfcf2 mt76: move mac_work in mt76_dev
334b4ce mt76: add mac80211 driver for MT7615 PCIe-based chipsets
edb2a00 mt76: add unlikely() for dma_mapping_error() check
355c079 mt76: use macro for sn and seq_ctrl conversion
133bffb add firmware for MT7615E
49d9c1b mt76: usb: reduce locking in mt76u_tx_tasklet
3e371ca mt76: set txwi_size according to the driver value
5007326 mt76: add skb pointer to mt76_tx_info
c47a568 mt76: dma: introduce skb field in mt76_txwi_cache
9029560 mt76: dma: add skb check for dummy pointer
e9eea39 mt76: mt7615: use sizeof instead of sizeof_field
98c5359 Revert "mt76: fix potential deadlock on cancelling workqueues"
bc9baa7 mt76x02u: remove bogus stop on suspend
6c1cab9 mt76usb: fix tx/rx stop
0e674c5 mt76x02: remove bogus mutex usage
59f7bb6 Revert "mt76: mt76x02: send no-skb tx status without holding the status lock"
b0f2a30 mt76x02: avoid status_list.lock and sta->rate_ctrl_lock dependency
62054de mt76: mt7603: remove query from mt7603_mcu_msg_send signature
e79d96a mt76: mt7603: use standard signature for mt7603_mcu_msg_send
be8f039 mt76: mt7603: initialize mt76_mcu_ops data structure
9a9c656 mt76: introduce mt76_mcu_restart macro
980b91e mt76: mt7603: init mcu_restart function pointer
a97db3f mt76: mt7603: run __mt76_mcu_send_msg in mt7603_mcu_send_firmware
151115f mt76: mt76x02: mt76x02_poll_tx() can be static
7391f98 mt76: fix endianness sparse warnings
6c06f73 mt76: mt7603: report firmware version using ethtool
f06647e mt76: usb: use EP max packet aligned buffer sizes for rx
f43fccf mt76: move beacon_int in mt76_dev
74ab2cf mt76: move beacon_mask in mt76_dev
23c2f94 mt76: add TX/RX antenna pattern capabilities
6e790e1 mt76: move pre_tbtt_tasklet in mt76_dev
7606c08 mt76: mt7603: enable/disable pre_tbtt_tasklet in mt7603_set_channel
ff22eee mt76: do not enable/disable pre_tbtt_tasklet in scan_start/scan_complete
3157385 mt76: mt7603: dynamically alloc mcu req in mt7603_mcu_set_eeprom
cc674e2 mt76: mt76x02: remove useless return in mt76x02_resync_beacon_timer
6b18427 mt76: move tx_napi in mt76_dev
bce63c4 mt76: mt7603: use napi polling for tx cleanup
4afd89e mt76: mt7615: use napi polling for tx cleanup
2cb4683 mt76: move netif_napi_del in mt76_dma_cleanup
b4ceb9f mt76: Fix a signedness bug in mt7615_add_interface()
d00dc95 mt76: mt7615: Use after free in mt7615_mcu_set_bcn()
4e0ccc6 mt76: mt7615: Make mt7615_irq_handler static
0fd552a mt7615: mcu: simplify __mt7615_mcu_set_wtbl
50f7094 mt7615: mcu: simplify __mt7615_mcu_set_sta_rec
4434d04 mt7615: mcu: remove bss_info_convert_vif_type routine
083fbb9 mt7615: mcu: use proper msg size in mt7615_mcu_add_wtbl_bmc
f61ca80 mt7615: mcu: use proper msg size in mt7615_mcu_add_wtbl
35bd12d mt7615: mcu: unify mt7615_mcu_add_wtbl_bmc and mt7615_mcu_del_wtbl_bmc
f8f990b mt7615: mcu: remove unused parameter in mt7615_mcu_del_wtbl
965bca1 mt7615: remove query from mt7615_mcu_msg_send signature
9b9ca18 mt7615: remove dest from mt7615_mcu_msg_send signature
935b7e5 mt7615: mcu: remove skb_ret from mt7615_mcu_msg_send
2442db4 mt7615: mcu: unify __mt7615_mcu_set_dev_info and mt7615_mcu_set_dev_info
645bc45 mt7615: mcu: do not use function pointers whenever possible
40c4201 mt7615: mcu: remove unused structure in mcu.h
a8834a2 mt7615: mcu: use standard signature for mt7615_mcu_msg_send
824d25c mt7615: initialize mt76_mcu_ops data structure
d943427 mt7615: mcu: init mcu_restart function pointer
c2211e4 mt7615: mcu: run __mt76_mcu_send_msg in mt7615_mcu_send_firmware
cb63a06 mt76: mt7603: stop mac80211 queues before setting the channel
c6aaa3a mt76: mt7615: rearrange cleanup operations in mt7615_unregister_device
97609f3 mt76: mt7615: add static qualifier to mt7615_rx_poll_complete
f9dadd2 mt76: mt7603: add debugfs knob to enable/disable edcca
89cda5d mt7603: fix reading target tx power from eeprom
77d0e33 mt76: fix setting chan->max_power
f575da2 mt76: mt76x02: fix tx status reporting issues
a5d18dc mt76: mt76x02: fix tx reordering on rate control probing without a-mpdu
bd32a93 mt76: mt76x02: remove enable from mt76x02_edcca_init signature
18386ee mt76: mt76x2u: remove mt76x02_edcca_init in mt76x2u_set_channel
da3514f mt76: mt76x2: move mutex_lock inside mt76x2_set_channel
0d4719c mt76: mt76x02: run mt76x02_edcca_init atomically in mt76_edcca_set
fd5af73 mt76: mt76x02: fix edcca file permission
a0f51f2 mt76: mt7615: do not process rx packets if the device is not initialized
753cdee mt76: mt7615: stop mcu first in mt7615_unregister_device
899efe7 mt76: move mt76_insert_ccmp_hdr in mt76-module
6960b6e mt76: mt7615: add support for mtd eeprom parsing
4bcb057 mt76: mt7615: select wifi band according to eeprom
866f2c6 mt76: generalize mt76_get_txpower for 4x4:4 devices
514fb04 mt76: mt7615: add the capability to configure tx power
ced9d43 mt76: mt7615: init get_txpower mac80211 callback
8abd502 mt76: mt7615: rearrange locking in mt7615_config
5b9b62e mt76: move mt76_get_rate in mt76-module
661c7c8 mt76: Remove set but not used variables 'pid' and 'final_mpdu'
f072c7b mt76: mt7615: enable support for mesh
28d9496 mt76: mt7615: fix slow performance when enable encryption
827b9ad mt76: mt7615: remove unused variable in mt7615_mcu_set_bcn
34eea14 mt76: mt7615: remove key check in mt7615_mcu_set_wtbl_key
2bfae5a mt76: usb: fix rx A-MSDU support
b033532 mt76: usb: do not always copy the first part of received frames
3e7fc15 mt76x02: fix reporting of non-probing frames with tx status requested
0d5caea Revert "mt76: usb: do not always copy the first part of received frames"
335e8c6 Revert "mt76: usb: fix rx A-MSDU support"
47ddf4b mt76: revert support for TX_NEEDS_ALIGNED4_SKBS
0b6520b mt7603: rework and fix tx status reporting
539b679 mt7603: improve hardware rate switching configuration
d86d6ef mt76x0: fix RF frontend initialization for external PA
f476a14 mt76x02: fix endian issue in tx status reporting patch
f8d0517 mt76: mt7615: simplify mt7615_mcu_set_sta_rec routine
73ff45f mt76: mt7615: add support for per-chain signal strength reporting
9b67ae6 mt76: mt7615: init per-channel target power
160fdc0 mt76: mt7615: take into account extPA when configuring tx power
2211d93 mt76: mt76x02u: fix sparse warnings: should it be static?
3750533 mt76: mt7615: fix incorrect settings in mesh mode
c37c1ca mt76: mt7615: update peer's bssid when state transition occurs
9dd1089 mt76: mt76u: reduce rx memory footprint
0789f45 mt76: mt7615: remove cfg80211_chan_def from mt7615_set_channel signature
2dca431 mt76: move nl80211_dfs_regions in mt76_dev data structure
3386ccf mt76: mt76u: get rid of {out,in}_max_packet
d680ab0 mt76: usb: fix rx A-MSDU support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
