This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331].
Specification
-------------
SOC: Qualcomm IPQ4018
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Ethernet: Qualcomm QCA8072 (2-port)
SPI Flash 1: Mactronix MX25L1605D (2MB)
SPI Flash 2: Winbond W25M02GV (256MB)
DRAM: Nanya NT5CC128M16IP-DI (256MB)
LED Controller: NXP PCA963x (I2C)
Buttons: Single reset button (GPIO).
Notes
-----
There does not appear to be a way to trigger TFTP recovery without entering
U-Boot. The device must be opened to access the serial console in order to
first flash OpenWrt onto a device from factory.
The device has automatic recovery backed by a second set of partitions on
the larger of the two SPI flash ICs. Both the primary and secondary must
be flashed to prevent accidental rollback to "factory" after 3 failed boot
attempts.
Serial console
--------------
A serial console is available on the following pins of the populated J2
connector on the device mainboard (115200 8n1).
(<-- Top of PCB / Device)
J2
[o o o o o o]
| | |
| | `-- GND
| `---- TX
`--------- RX
Installation instructions
-------------------------
1. Setup TFTP server with server IP set to 192.168.1.236.
2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Revert to "factory"
-------------------
1. Download latest firmware update from vendor support site.
2. Copy extracted `.img` file to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Link: https://github.com/openwrt/openwrt/pull/3682
Signed-off-by: Peter Adkins <peter@sunkenlab.com>
(calibration from nvmem, updated to 5.10+5.15)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Aruba deploys a BDF in the root filesystem, however this matches the one
used for the DK04 reference board.
The board-specific BDFs are built into the kernel. The AP-365 shows
sinificant degraded performance with increased range when used with the
reference BDF.
Replace the BDF with the one extracted from Arubas kernel.
Signed-off-by: David Bauer <mail@david-bauer.net>
Avoid shipping ath10k board file in Mikrotik initram images
Most will only ever need to use these initram images once—to initially
load OpenWrt, but fix these images for more consistent Wi-Fi performance
between the initram and installed squashfs images.
OpenWrt BUILDBOT config ignores -cut packages in the initram images build.
This results in BUILDBOT initram images including the linux-firmware
qca4019 board-2.bin, and (initram image booted) Mikrotik devices loading
a generic BDF, rather than the intended BDF data loaded
from NOR as an api 1 board_file.
buildbot snapshot booted as initram image:
cat /etc/openwrt_version
r19679-810eac8c7f
dmesg | grep ath10k | grep -E board\|BDF
[ 9.794556] ath10k_ahb a000000.wifi: Loading BDF type 0
[ 9.807192] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:16
crc32 11892f9b
[ 12.457105] ath10k_ahb a800000.wifi: Loading BDF type 0
[ 12.464945] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:17
crc32 11892f9b
CC: Robert Marko <robimarko@gmail.com>
Fixes: 5eee67a72f ("ipq40xx: mikrotik: dont include ath10k-board-qca4019 by default")
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Since MikroTik subtarget now uses dynamic BDF loading its crucial that it
doesnt include the board-2.bin at all which is provided by the
ath10k-board-qca4019 package.
So to resolve this dont include the ath10k-board-qca4019 package on the
MikroTik subtarget.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since we now provide the BDF-s for MikroTik IPQ40xx devices on the fly,
there is noneed to include package and ship them like we do now.
This also resolves the performance issues that happen as MikroTik
changes the boards and ships them under the same revision but they
actually ship with and require a different BDF.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since we now can pass the API 1 BDF-s aka board.bin to the ath10k
driver per radio lets use that to provide the BDF-s for MikroTik devices.
This also resolves the performance issues that happen as MikroTik changes
the boards and ships them under the same revision but they actually ship
with and require a different BDF.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC in
contrast to the Macronix NAND with 4 bit ECC. This removes the hardcoded
ECC strength and step size as set in qcom-ipq4019.dtsi, thus relying on the
kernel NAND detection routines to correclty set up the ECC parameters.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Commit f4fb63d2ab ("ipq40xx: 5.10: move AR40xx to MDIO drivers") moved
the ar40xx driver files to kernel version specific directories to place
them in different subdirectory in kernel tree. But now kernel 5.4 is
gone and there is no reason to keep them separate. Move them back to
common files/ directory.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Also apply commit ab7e53e5cc ("ipq40xx: 5.10: fix ar40xx driver") to
5.15 driver.
The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code, these mdelays were existing, but in
the ar41xx.c they are gone.
Fixes: 87318eb179 ("ipq40xx: 5:15: copy config and patch from 5.10")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Patch that corrects sleep clock frequency has already been backported
to 5.15 stable so remove the duplicate patch.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add 5.15 kernel as a testing kernel version in the Makefile.
Linksys EA6350v3/EA8300/MR8300 will not build with buildbot settings and
should be disabled when the target is switched, unless the image size is
reduced again.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
[add comment for increased kernel size]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Kernel 5.15 have some new api for ethtool and phy.
Add ifdef to fix compilation error.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
This commit is completely based on the work of adron-s:
https://github.com/openwrt/openwrt/pull/4721#issuecomment-1101108651
The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code [0], these mdelays were existing, but
in the ar41xx.c they are gone.
Tested on:
- Fritz!Box 4040
- Fritz!Box 7530
- Mikrotik SXTsq 5AC
- ZyXEL NBG6617
- [0] https://git.codelinaro.org/clo/qsdk/oss/lklm/qca-ssdk/-/blob/NHSS.QSDK.11.4/src/init/ssdk_init.c#L2072
Suggested-by: Serhii Serhieiev <adron@mstnt.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
This reverts commit 35d2bbc29b as we
believe we found that it is indeed an openssl issue, where openssl is
trying to use getrandom(2), but fails because this particular builder
has an ancient kernel without that syscall. We didn't get to the bottom
of why openssl doesn't fall back to something like /dev/random.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
the buildbots are having troubles with the image.
They seem to get "Killed" at the last step of the KERNEL rule:
|/cros-vbutil -k zImage.itb.vboot -c "root=PARTUUID=%U/PARTNROFF=1" -o zImage.itb.vboot.new
|make[4]: *** [Makefile:18: zImage.itb.vboot] Killed
Since the Google Wifi (Gale) is currently the only target in
this sub-target. So this means that subtarget has to be disabled
from the time being to not be picked up by the builders.
For people wanting to checkout out OpenWrt on the Google Wifi:
please compile it locally.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
removes usb-port remains as neither the WAC510 nor the WAC505
come with a USB port. Update the LED properties to phase out
labels and introduce generic node-names as well as adding
the color, function and function-enumerator properties.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Modified the radio frequency hardware part of e2600ac c1/c2,
need to cooperate with the modified board.bin file, the device
can work normally.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
This model, also know as "1&1 HomeServer", shares the same features as 7530.
The vendor firmware has artificial software limitations: only 2 of the 4
LAN-Ports are GBit, and the USB-Host is only v2.0.
With OpenWrt, USB is already working at v3.0.
Signed-off-by: Andre Heider <a.heider@gmail.com>
(updated commit message to reflect current state)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Google WiFi (codename: Gale) is an IPQ4019-based AP, with 2 Ethernet
ports, 2x2 2.4+5GHz WiFi, 512 MB RAM, 4 GB eMMC, and a USB type C port.
In its stock configuration, it runs a Chromium OS-based system, but you
wouldn't know it, since you can only manage it via a "cloud" +
mobile-app system.
The "v2" label is coded into the bootloader, which prefers the
"google,gale-v2" compatible string. I believe "v1" must have been
pre-release hardware.
Note: this is *not* the Google Nest WiFi, released in 2019.
I include "factory.bin" support, where we generate a GPT-based disk
image with 2 partitions -- a kernel partition (using the custom "Chrome
OS kernel" GUID type) and a root filesystem partition. See below for
flashing instructions.
Sysupgrade is supported via recent emmc_do_upgrade() helper.
This is a subtarget because it enables different features
(FEATURES=boot-part rootfs-part) whose configurations don't make sense
in the "generic" target, and because it builds in a few USB drivers,
which are necessary for installation (installation is performed by
booting from USB storage, and so these drivers cannot be built as
modules, since we need to load modules from USB storage).
Flashing instructions
=====================
Documented here:
https://openwrt.org/inbox/toh/google/google_wifi
Note this requires booting from USB storage.
Features
========
I've tested:
* Ethernet, both WAN and LAN ports
* eMMC
* USB-C (hub, power-delivery, peripherals)
* LED0 (R/G/B)
* WiFi (limited testing)
* SPI flash
* Serial console: once in developer mode, console can be accessed via
the USB-C port with SuzyQable, or other similar "Closed Case
Debugging" tools:
https://chromium.googlesource.com/chromiumos/third_party/hdctools/+/master/docs/ccd.md#suzyq-suzyqable
* Sysupgrade
Not tested:
* TPM
Known not working:
* Reboot: this requires some additional TrustZone / SCM
configuration to disable Qualcomm's SDI. I have a proposal upstream,
and based on IRC chats, this might be acceptable with additional DT
logic:
[RFC PATCH] firmware: qcom_scm: disable SDI at boot
https://lore.kernel.org/linux-arm-msm/20200721080054.2803881-1-computersforpeace@gmail.com/
* SMP: enabling secondary CPUs doesn't currently work using the stock
bootloader, as the qcom_scm driver assumes newer features than this
TrustZone firmware has. I posted notes here:
[RFC] qcom_scm: IPQ4019 firmware does not support atomic API?
https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/
* There's a single external button, and a few useful internal GPIO
switches. I haven't hooked them up.
The first two are fixed with subsequent commits.
Additional notes
================
Much of the DTS is pulled from the Chrome OS kernel 3.18 branch, which
the manufacturer image uses.
Note: the manufacturer bootloader knows how to patch in calibration data
via the wifi{0,1} aliases in the DTB, so while these properties aren't
present in the DTS, they are available at runtime:
# ls -l
/sys/firmware/devicetree/base/soc/wifi@a*/qcom,ath10k-pre-calibration-data
-r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a000000/qcom,ath10k-pre-calibration-data
-r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a800000/qcom,ath10k-pre-calibration-data
Ethernet MAC addresses are similarly patched in via the ethernet{0,1} aliases.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(updated 901 - x1pro moved in the process)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
See my upstream questions:
https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/
This effectively reverts upstream Linux commit 13e77747800e ("firmware:
qcom: scm: Use atomic SCM for cold boot"), because Google WiFi boot
firmwares don't support the atomic variant.
This fixes SMP support for Google WiFi.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
See firmware-utils.git commits [1], which implemented the cros-vbutil
verified-boot payload-packing tool, and extended ptgen for the CrOS
kernel partition type. With these, it's now possible to package kernel +
rootfs to make disk images that can boot a Chrome OS-based system (e.g.,
Chromebooks, or even a few AP models).
Regarding PARTUUID= changes: Chromium bootloaders work well with a
partition number offset (i.e., relative to the kernel partition), so
we'll be using a slightly different root UUID line.
NB: I've made this support specific to ip40xx for now, because I only
plan to support an IPQ4019-based AP that uses a Chromium-based
bootloader, but this image format can be used for essentially any
Chromebook, as well as the Google OnHub, a prior Chromium-based AP using
an IPQ8064 chipset.
[1]
ptgen: add Chromium OS kernel partition support
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=6c95945b5de973026dc6f52eb088d0943efa96bb
cros-vbutil: add Chrome OS vboot kernel-signing utility
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=8e7274e02fdc6f2cb61b415d6e5b2e1c7e977aa1
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tel(co Electronics) X1 Pro is preventing ipq40xx generic
from building due to the KERNEL_SIZE.
Whenever bigger kernels are possible, if lzma is supported
is unknown.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Telco X1 Pro is a Cat12 LTE-A Pro modem router.
Vendor firmware is based on a recent version of OpenWrt.
Flashing is possible via CLI using sysupgrade -F -n
The serial headers allow bootloader and console access
Serial setting: 115200 8N1
Brief Specifications:
IPQ4019 SoC
32MB flash
512MB RAM
4x gigabit LAN
1x gigabit WAN
Dual-band Wave-2 wifi
2x SMA LTE antenna connectors
2x RP-SMA wifi antennas
1x USB 2.0 port
1x Reset button
Serial headers installed
1x Nano SIM tray
1x Quectel EM-12G LTE-A Pro modem
1x M.2 slot attached to USB 3.0
1x internal micro SD card slot
Signed-off-by: Nicholas Smith <nicholas@nbembedded.com>
Enable support for allocating user space page table entries in high memory [1],
for the targets which support this feature. This saves precious low memory
(permanently mapped, the only type of memory directly accessible by the kernel).
[1] https://www.kernel.org/doc/html/latest/vm/highmem.html
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fix the missing ;; after the cAP ac case in /e/b/01_leds.
Fixes: 93d9119 ("ipq40xx: add MikroTik cAP ac support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (minor touch-up)
Enrico provided a bootlog that shows the chip is a WAVE-2 QCA9888v2:
> pci 0000:01:00.0: [168c:0056] type 00 class 0x028000
> [...]
> ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x56.
> ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 [...] chip_id 0x00000000 sub 0000:0000
> ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5 features mfp,[...]
> ath10k_pci 0000:01:00.0: board_file api 2 bmi_id N/A crc32 6535d835
> ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 32 raw 0 hwcrypto 1
this patch switches the device over to pre-calibration.
(this is more or less cosmetic)
Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The PCIe and built-in 5GHZ radios are meant to operate on different
frequency bands. The hardware enforces this via RF filters.
Add this information to allow software enforcing it as well.
Credits to Piotr Dymacz for the invaluable help.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
This makes the WAN interface and port appear in
LuCi -> Network -> Switch on Linksys MR8300.
This allows to configure a VLAN on WAN.
Fixes: FS#4227
Signed-off-by: Julien Cassette <julien.cassette@gmail.com>
ZTE MF286D is a LTE router with four gigabit ethernet ports
and integrated QMI mPCIE modem.
Hardware specification:
- CPU: IPQ4019
- RAM: 256MB
- Flash: NAND 128MB + NOR 2MB
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2
- LTE: mPCIe cat 12 card (Modem chipset MDM9250)
- LAN: 4 Gigabit Ports
- USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem)
- Serial console: X8 connector 115200 8n1
Known issues:
- Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs
are driven by cpu.
- Wifi LED is triggered by phy0tpt only
- No VoIP support
- LAN1/WAN port is configured as WAN
- ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN
and WLAN0/1
Opening the case:
1. Take of battery lid (no battery support for this model, battery cage
is dummy).
2. Unscrew screw placed behind battery lid.
3. Take off back cover. It attached with multiple plastic clamps.
4. Unscrew four more screws hidden behind back case.
5. Remove front panel from blue chassis. There are more plastic
clamps.
6. Unscrew two boards, which secures the PCB in the chassis.
7. Extract board from blue chassis.
Console connection (X8 connector):
1. Parameters: 115200 8N1
2. Pin description: (from closest pin to X8 descriptor to farthest)
- VCC (3.3V)
- TX
- RX
- GND
Install Instructions:
Serial + initramfs:
1. Place OpenWrt initramfs image for the device on a TFTP in
the server's root. This example uses Server IP: 192.168.1.3
2. Connect serial console (115200,8n1) to X8 connector.
3. Connect TFTP server to RJ-45 port.
4. Stop in u-Boot and run u-Boot commands:
setenv serverip 192.168.1.3
setenv ipaddr 192.168.1.72
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert
to stock.
6. Login via ssh or serial and remove stock partitions:
ubiattach -m 9
ubirmvol /dev/ubi0 -N ubi_rootfs
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. Install image via "sysupgrade -n".
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cosmetic changes to the commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This moves bootargs-append support patch from ipq40xx and ipq806x to
generic. This way we can append additional boot arguments from DTS instead
of only being able to overwrite them.
This is a preparation for kirkwood support of ipTIME NAS1.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Assign LED numbers properly by adding function-enumerator property in DTS.
While at it, remove default trigger of LAN LEDs as it will be handled in
01_leds anyway.
Fixes: 51b9aef553 ("ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Chen Minqiang reported on github:
| DTC arch/arm/boot/dts/qcom-ipq4029-ap-365.dtb
|qcom-ipq4019.dtsi:520.23-560.5: ERROR (phandle_references): /soc/wifi@a000000:
|Reference to non-existent node or label "macaddr_mfginfo_1d"
|
| also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:243.8-248.3
|qcom-ipq4019.dtsi:562.23-602.5: ERROR (phandle_references): /soc/wifi@a800000:
|Reference to non-existent node or label "macaddr_mfginfo_1d"
|
| also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:250.8-256.3
|ERROR: Input tree has errors, aborting (use -f to force output)
|scripts/Makefile.lib:326: recipe for target 'qcom-ipq4029-ap-365.dtb' failed
Fixes: cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
moves extraction entries out of 11-ath10k-caldata and into
the individual board's device-tree.
Some notes:
- mmc could work as well (not tested)
- devices that pass the partitions via mtdparts
bootargs are kept as is
- gl-b2200 has a weird pcie wifi device
(vendor claims 9886 wave 2. But firmware-extraction
was for a wave 1 device?!)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SOC: IPQ4019
CPU: Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
DRAM: 256 MB
NAND: 128 MiB Macronix MX30LF1G18AC
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN)
USB: 1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
WLAN2: Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4
INPUT: 1x WPS, 1x Reset
LEDS: Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN
This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed
with an intermediary initramfs image, the jffs2 ubi volume deleted, and
then finally a sysupgrade with the final image performed.
Signed-off-by: Joshua Roys <roysjosh@gmail.com>
(added ALT0)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*Had to revert 7f1edbd in order to build due to FS#4149
Signed-off-by: John Audia <graysky@archlinux.us>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
The workqueue based implementation has a few corner cases and typically lower
performance than the upstream one
Signed-off-by: Felix Fietkau <nbd@nbd.name>
GL.iNet's U-Boot checks for GPIO 40, not 43.
Changing this allows the RESET button to work as expected.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Daniel Golle <daniel@makrotopia.org>
CC: Li Zhang <li.zhang@gl-inet.com>
introduce nvmem pre-cal + mac-address cells for both Wifis
and ethernet on the EZVIZ CS-W3-WD1200G EUP. This is one of
the few devices in which the correct mac adress is already
at the right place for Wifi, so no separate nvmem cell is
needed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
with current images, the device is no longer booting.
It gets stuck in the bootloader with "Config not available"
and drops to the uboot shell.
|flash_type: 0
|Hit any key to stop autoboot: 0
|SF: Detected MX25L12805D with page size 4 KiB, total 16 MiB
|Config not availabale
|(IPQ40xx) #
This is because the default bootcmd "bootipq" will only read
the first four MiB of the kernel image. With 5.10 the gzip'd
kernel is slightly larger. So the part of the FIT image which
had the configuration is cut off. Hence it can't find it.
To update the bootcmd, you have to attach the serial console
again and enter the following commands into the boot prompt:
# setenv bootcmd "sf probe; sf read 84000000 180000 600000; bootm"
# saveenv
# run bootcmd
This will allow booting kernels with up to six MiB. This also
allows us to drop the DEVICE_DTS_CONFIG hack we had to use.
Note:
uboot doesn't support LZMA. It fails with:
"Unimplemented compression type 3"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The commented out code is not required, as the comment
indicates.
The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones. This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized. It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
This patch adds supports for the GL-B2200 router.
Specifications:
- SOC: Qualcomm IPQ4019 ARM Quad-Core
- RAM: 512 MiB
- Flash: 16 MiB NOR - SPI0
- EMMC: 8GB EMMC
- ETH: Qualcomm QCA8075
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
- WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
- INPUT: Reset, WPS
- LED: Power, Internet
- UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
- UART2: On board with BLE module
- SPI1: On board socket for Zigbee module
Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.
What's working:
- WiFi 2G, 5G
- WPA2/WPA3
Not tested:
- Bluetooth LE/Zigbee
Credits goes to the original authors of this patch.
V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade
Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
LHGG-60ad is IPQ4019 + wil6210 based.
Specification:
- Qualcomm IPQ4019 (717 MHz)
- 256 MB of RAM (DDR3L)
- 16 MB (SPI NOR) of flash
- 1x Gbit ethernet, 802.3af/at POE IN connected through AR8035.
- WLAN: wil6210 802.11ad PCI card
- No USB or SD card ports
- UART disabled
- 8x LEDs
Biggest news is the wil6210 PCI card.
Integration for its configuration and detection has already been taken
care of when adding support for TP-Link Talon AD7200.
However, signal quality is much lower than with stock firmware, so
probably additional board-specific data has to be provided to the
driver and is still missing at the moment.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[Fix Ethernet Interface]
Signed-off-by: Nick Hainke <vincent@systemli.org>
This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.
The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.
See https://teltonika-networks.com/product/rutx10 for more info.
Hardware:
SoC: Qualcomm IPQ4018
RAM: 256MB DDR3
SPI Flash 1: XTX XT25F128B (16MB, NOR)
SPI Flash 2: XTX XT26G02AWS (256MB, NAND)
Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
USB Hub: Genesys Logic GL852GT
Bluetooth: Qualcomm CSR8510 (A10U)
LED/GPIO controller: STM32F030 with custom firmware
Buttons: Reset button
Leds: Power (green, cannot be controlled)
WiFi 2.4G activity (green)
WiFi 5G activity (green)
MACs Details verified with the stock firmware:
eth0: Partition 0:CONFIG Offset: 0x0
eth1: = eth0 + 1
radio0 (2.4 GHz): = eth0 + 2
radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.
The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt
USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.
Flash instructions via stock web interface (sysupgrade based):
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
5. Open stock web interface at http://192.168.1.1
6. Set some password so the web interface is happy
7. Go to firmware upgrade settings
8. Choose
openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
9. Set 'Keep settings' to off
10. Click update, when warned that it is not a signed image proceed
Return to stock firmware:
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.
Signed-off-by: Felix Matouschek <felix@matouschek.org>
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.
See https://mikrotik.com/product/hap_ac3 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4019
- RAM: 256 MB
- Storage: 16 MB NOR + 128 MB NAND
- Wireless:
· Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
· Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
- Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in, PoE passtrough on port 5
- 1x USB Type A port
Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Mark Birss <markbirss@gmail.com>
Tested-by: Michael Büchler <michael.buechler@posteo.net>
Tested-by: Alex Tomkins <tomkins@darkzone.net>
the Netgear EX6100v2 and EX6150v2 can utilize the nvmem
for the pre-calibration and mac-address for both WIFI
devices.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
these flags have been creeping in from the QSDK.
All needed clocks should be accounted for, and
if a device is broken due to this. It should be
looked into.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch fixes a blunder of mine. The include needed
for LED_COLOR_ID_BLUE property is missing.
This caused the builds to fail with:
|Error: arch/arm/boot/dts/qcom-ipq4019-r619ac.dtsi:91.13-14 syntax error
|FATAL ERROR: Unable to parse input tree
Fixes: 12d33d388c ("ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Zyxel NBG6617 already uses lzma to compress the kernel.
A local build with every module enabled (either as =Y or =M)
ended produced a 3058 KiB kernel (the kernel partition is 4MiB).
It booted just fine, let's reenable the device.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
P&W R619AC is a IPQ4019 Dual-Band AC1200 router.
It is made by P&W (p2w-tech.com) known as P&W R619AC
but marketed and sold more popularly as G-DOCK 2.0.
Specification:
* SOC: Qualcomm Atheros IPQ4019 (717 MHz)
* RAM: 512 MiB
* Flash: 16 MiB (NOR) + 128 MiB (NAND)
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN)
* Wireless:
- 2.4 GHz b/g/n Qualcomm Atheros IPQ4019
- 5 GHz a/n/ac Qualcomm Atheros IPQ4019
* USB: 1 x USB 3.0
* LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED)
* Input: 1 x reset
* 1 x MicroSD card slot
* Serial console: 115200bps, pinheader J2 on PCB
* Power: DC 12V 2A
* 1 x Unpopulated mPCIe Slot (see below how to connect it)
* 1 x Unpopulated Sim Card Slot
Installation:
1. Access to tty console via UART serial
2. Enter failsafe mode and mount rootfs
<https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset>
3. Edit inittab to enable shell on tty console
`sed -i 's/#ttyM/ttyM/' /etc/inittab`
4. Reboot and upload `-nand-factory.bin` to the router (using wget)
5. Use `sysupgrade` command to install
Another installation method is to hijack the upgrade server domain
of stock firmware, because it's using insecure http.
This commit is based on @LGA1150(at GitHub)'s work
<a4932c8d5a>
With some changes:
1. Added `qpic_bam` node in dts. I don't know much about this,
but I observed other dtses have this node.
2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not
working. This fix is from
<51143b4c75>
3. Removed the 32MB NOR variant.
4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes
wlan2g led light up.
5. Added ethphy led config in dts.
6. Changed nand partition label from `rootfs` to `ubi`.
About the 128MiB variant: The stock bootloader sets size of nand to 64MiB.
But most of this devices have 128MiB nand. If you want to use all 128MiB,
you need to modify the `MIBIB` data of bootloader. More details can be
found on github:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060>
For instructions on how to flash the MIBIB partition from u-boot console:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232>
About the Mini PCIe slot: (from "ygleg")
"The REFCLK signals on the Mini PCIe slot is not connected on
this board out of the box. If you want to use the Mini PCIe slot
on the board, you need to (preferably) solder two 0402 resistors:
R436 (REFCLK+) and R444 (REFCLK-)..."
This and much more information is provoided in the github comment:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670>
Signed-off-by: Richard Yu <yurichard3839@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
[Added comment about MIBIB+128 MiB variant. Added commit
message section about pcie slot. Renamed gpio-leds' subnodes
and added color, function+enum properties.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
After switch to 5.10 kernel, kernel size was too high.
This patch switches Cell-C RTL30VW from uImage to zImage build.
Lzma uImage wrap is required for factory booting and it must left
untouched.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
It looks like CONFIG_BLK_CMDLINE_PARSER was forgotten during the Orbi
device merge.
So lets refresh the config with it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Disable some of the ipq40xx devices due to their kernel size limitations.
These devices fail to build with kernel 5.10 and full buildbot config.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[keep gl-b1300/gl-s1300 enabled, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There have been enough tests and new developments require the new
kernel, so let's update it.
There is a bunch of devices that do not build anymore due to
kernel size limitations. These are disabled in a subsequent commit.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost
identical AC3000 routers. The SRR60 has one port labeled as wan while
the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a
different external shape but they have an USB 2.0 port on the back.
This patch has been tested only on SRS60 and RBR50, but should work
on SRR60 and RBS50.
Hardware
--------
SoC: Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads)
RAM: 512MB DDR3
FLASH: 4GB EMMC
ETH:
- 3x 10/100/1000 Mbps Ethernet
- 1x 10/100/1000 Mbps Ethernet (WAN)
WIFI:
- 2.4GHz: 1x IPQ4019 (2x2:2)
- 5GHz: 1x IPQ4019 (2x2:2)
- 5GHz: 1x QCA9984 (4x4:4)
- 6 internal antennas
BTN:
- 1x Reset button
- 1x Sync button
- 1x ON/OFF button
LEDS:
- 8 leds controlled by TLC59208F (they can be switched on/off
independendently but the color can by changed by GPIOs)
- 1x Red led (Power)
- 1x Green led (Power)
UART:
- 115200-8-N-1
Everything works correctly.
Installation
------------
These routers have a dual partition system. However this firmware works
only on boot partition 1 and the OEM web interface will always flash on
the partition currently not booted.
The following steps will use the SRS60 firmware, but you have to chose
the right firmware for your router.
There are 2 ways to install Openwrt the first time:
1) Using NMRPflash
1. Download nmrpflash (https://github.com/jclehner/nmrpflash)
2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img
file in the same folder of the nmrpflash executable
3. Connect your pc to the router using the port near the power button.
4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img".
Replace XXX with your network interface (can be identified by
running "nmrpflash -L")
5. Power on the router and wait for the flash to complete. After about
a minute the router should boot directly to Openwrt. If nothing
happens try to reboot the router. If you have problems flashing
try to set "10.164.183.253" as your computer IP address
2) Without NMRPflash
The OEM web interface will always flash on the partition currently not
booted, so to flash OpenWrt for the first time you have to switch to
boot partition 2 and then flash the factory image directly from the OEM
web interface.
To switch on partition 2 you have to enable telnet first:
1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet".
2. Connect through telent ("telnet 192.168.1.250") and login using
admin/password.
To read the current boot_part:
artmtd -r boot_part
To write the new boot_part:
artmtd -w boot_part 02
Then reboot the router and then check again the current booted
partition
Now that you are on boot partition 2 you can flash the factory Openwrt
image directly from the OEM web interface.
Restore OEM Firmware
--------------------
1. Download the stock firmware from official netgear support.
2. Follow the nmrpflash procedure like above, using the official
Netgear firmware (for example SRS60-V2.2.1.210.img)
nmrpflash -i XXX -f SRS60-V2.2.1.210.img
Notes
-----
1) You can check and edit the boot partition in the Uboot shell using
the UART connection.
"boot_partition_show" shows the current boot partition
"boot_partition_set 1" sets the current boot partition to 1
2) Router mac addresses:
LAN XX:XX:XX:XX:XX:69
WAN XX:XX:XX:XX:XX:6a
WIFI 2G XX:XX:XX:XX:XX:69
WIFI 5G XX:XX:XX:XX:XX:6b
WIFI 5G (2nd) XX:XX:XX:XX:XX:6c
LABEL XX:XX:XX:XX:XX:69
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved
sysupgrade mmc.sh to here and renamed it, various dtsi changes]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
CONFIG_CMDLINE_PARTITION:
Some devices with mmc like the Netgear Orbi Pro SRS60 or Netgear Orbi
RBR50 needs to hardcode the partitions layout in the cmdline boot
correctly
CONFIG_LEDS_TLC591XX:
This is needed for the led driver found in the Netgear Orbi Pro SRS60
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Shang Jia <jiash416@gmail.com>
[added 5.10 config]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It seems like sleep_clk was copied from ipq806x.
Fix ipq40xx sleep_clk to the value QSDK defines.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [5.4+5.10]
Back in the day, the board-2.bin came with ath10k-firmware-qca4019.
This changed with
commit c3b2efaf24 ("linux-firmware: ath10k: add board firmware packages")
which placed the board-2.bin into a separate package: ath10k-board-qca4019.
This was great, because it addressed one of the caveat of the original
ipq-wifi package:
commit fa03d441e9 ("firmware: add custom IPQ wifi board definitions")
| 2. updating ath10k-firmware-qca4019 will also replace
| the board-2.bin. For this cases the user needs to
| manually reinstall the wifi-board package once the
| ath10k-firmware-qca4019 is updated.
This could be extended further so that ipq-wifi packages
no longer use "install-override" and the various QCA4019
variants list the ath10k-board-qca4019 as a CONFLICT
package.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This is a backport of Ansuel Smith's "Multiple improvement to qca8k stability"
series. The QCA8337 switch is available on multiple platforms including
ipq806x, ath79 and bcm53xx.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
In the "ipq40xx: switch to Kernel 5.10" discussion at GitHub,
Adrian noted [0] that these GL.iNet Conexa series devices,
GL-B1300 and GL-S1300 failed their image generation [1] as their gzipped
uImage kernel went above 4096k.
While notifying the vendor about this problem [2], I tested all U-Boot
releases from GL.iNet:
- they really fail to boot kernel above 4096k
- they don't support lzma: "Unimplemented compression type 3"
- but they boot zImage
Using zImage (xz compression) the kernel is 2909k which is
more than a megabyte away from the KERNEL_SIZE := 4096k limit.
The gzip compressed version would be 4116k.
[0]: https://github.com/openwrt/openwrt/pull/4620#issuecomment-932765776
[1]: commit 7b1fa276f5 ("ipq40xx: add testing support for kernel 5.10")
[2]: https://forum.gl-inet.com/t/ipq40xx-kernel-size-and-u-boot-v5-10-is-too-big-for-4-mb/17619
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Add kernel 5.10 as the testing kernel to ipq40xx to
get wider testing.
The following devices failed to build with buildbot settings and all
feeds installed (apparently due to kernel size):
* cell-c rtl30vw
* compex wpj428
* devolo magic 2 next
* engenius emr3500
* glinet gl-b1300
* glinet gl-s1300
* qcom ap-dk01.1-c1
* qcom ap-dk04.1-c1
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Nick Hainke <vincent@systemli.org> [ipq4019/fritzbox-7530
ipq4019/fritzbox-4040
ipq4019/sxtsq-5ac]
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ipq4029/gl-b1300]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq4019/map-ac2200]
[add tested-by and note about failed devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MDIO drivers were moved into their own sub directory of networking drivers.
This has caused the AR40xx driver to probe before MDIO drivers and that wont
work as it depends on the MDIO bus to be up so it can be fetched.
Lets solve it by moving the AR40xx into MDIO folder so they get probed like
before.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
This is a required ethtool op since kernel 5.7.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In kernel v5.5 of_get_phy_mode had its API changed, so its now returning 0
or errors instead of phymode.
Phymode is now returning by passing a pointer to phy_interface_t where it
will be stored.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Copy config from 5.4 and run "make kernel_oldconfig".
Select default ("N") for all new symbols.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[make commit message more explicit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Refresh the kernel patches on top of 5.10 so they apply.
Manually fixup the 705-net-add-qualcomm-ar40xx-phy.patch
to apply.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
USB and SDHCI LDO DTS patches have been upstreamed into 5.12, so
replace the local versions with upstreamed ones.
Reorder, and clearly mark the kernel version.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The board data file for the Plasma Cloud PA2200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.
Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the Plasma Cloud PA1200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.
Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the EnGenius EMR3500 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.
Fixes: 3f61e5e1b9 ("ipq40xx: add support for EnGenius EMR3500")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the EnGenius EMD1 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.
Fixes: 51f3035978 ("ipq40xx: add support for EnGenius EMD1")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60
seconds to 21 seconds in 2012 in the upstream kernel. Some targets
already use 21 seconds.
This patch changes the default value in the generic configuration to 21
seconds and removes the target specific configuration options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The bootloader will look for a configuration section named ap.dk01.1-c2
in the FIT image. If this doesn't exist, the device won't boot.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This resolves incosnsitencies of the configured RX / TX flow control
modes between different boards or bootloaders.
Signed-off-by: David Bauer <mail@david-bauer.net>
The chip supports clock speeds up to 50 MHz, however it won't even read
the chip-id correctly at this frequency.
45 MHz however works reliable.
Signed-off-by: David Bauer <mail@david-bauer.net>
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
When the AVM FRITZ!Repeater 1200 was introduced on Kernel 4.19, the
at803x PHY driver incorrectly set up the delays, not disabling delays
set by the bootloader.
The PHY was always operating with RX as well as TX delays enabled, but
with kernel 5.4 and later, the required TX delay is disabled, breaking
ethernet operation.
Correct the PHY mode, so the driver enables both delays.
Signed-off-by: David Bauer <mail@david-bauer.net>
The mx25l25635f supports clock speed up to 50Mhz.
Also remove obsolete "mx25l25635f" hack and rename
the matching device-tree flash node.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[mention node rename as well. chip is very very likely
always the "f" revision for all NBG6617]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.
While at it, do some obvious wrapping improvements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
Though not strictly necessary, add the closing symbol to make the
job easier for future developers editing this file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When support for Luma WRTQ-329ACN was added, the instructions for
flashing this device include using tools from uboot-envtools package.
Unfortunately the OpenWrt buildroot system omits packages from
DEVICE_PACKAGES when CONFIG_TARGET_MULTI_PROFILE,
CONFIG_TARGET_PER_DEVICE_ROOTFS, CONFIG_TARGET_ALL_PROFILES are set. In
result the official images are without tools mentioned in the
instruction. The workoround for the fashing would be installing
uboot-envtools when booted with initramfs image, but not always the
access to internet is available. The other method would be to issue the
necesary command in U-Boot environment but some serial terminals default
configuration don't work well with pasting lines longer than 80 chars.
Therefore add uboot-envtools to default packages, which adds really
small flash footprint to rootfs, where increased size usually is not an
issue.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Many people appear to use an unneeded "+" prefix for the increment
when calculating a MAC address with macaddr_add. Since this is not
required and used inconsistently [*], just remove it.
[*] As a funny side-fact, copy-pasting has led to almost all
hotplug.d files using the "+", while nearly all of the
02_network files are not using it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.
For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>
Specifications:
SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
Flash1: 2 MiB Winbond W25Q16JV SPI-NOR
Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
WAN port active IEEE 802.3af/at PoE in
Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial: Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
The Serial settings are 115200-8-N-1.
Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.
In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.
Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.
Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm
Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:
Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[ 1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.
Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The routerbootparts driver dynamically discovers the location of MikroTik
partitions, but it cannot determine their size (except by extending them
up to the start of the next discovered partition).
The hard_config partition has a default size of 0x1000 in the driver,
while it actually takes 0x2000 on the hAP-ac2. Set the correct size in
the hAP-ac2 DTS.
On most devices, this isn't a problem as the actual data fits in 0x1000
bytes. However, some devices have larger data that doesn't fit in 0x1000
bytes. In any case, all devices seen so far have enough space for a
0x2000 hard_config partition before the start of the dtb_config partition.
With the current 0x1000 size:
0x00000000e000-0x00000000f000 : "hard_config"
0x000000010000-0x000000017bbc : "dtb_config"
With this patch extending the size to 0x2000:
0x00000000e000-0x000000010000 : "hard_config"
0x000000010000-0x000000017bbc : "dtb_config"
Other ipq40xx boards may need the same fix but it needs testing.
References: https://forum.openwrt.org/t/support-for-mikrotik-hap-ac2/23333/324
Acked-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93
Signed-off-by: John Audia <graysky@archlinux.us>
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
- Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
- 1x Ethernet LED (green)
- 7x user-controllable LEDs
· 1x power (blue)
· 1x user (green)
· 5x rssi (green)
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
The bootloader of many ipq40xx boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq40xx.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While rebasing into setting bits instead of magic values,
I accidentally forgot to actually set the force bit.
Without it using the pins as GPIO-s did not actually work.
Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.
This commit involved `update_kernel.sh -v -u 5.4`.
Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The variables KERNEL_INITRAMFS_PREFIX and KERNEL_PREFIX are already
defined in include/image.mk and don't have to be redefined in the
target Makefiles.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[also cover imx6]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On a platform with many very different devices, like found on ipq40xx,
the generic profile seems like a remnant of the past that does not
have a real use anymore.
Remove it to have one thing less to maintain.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since generic images have been split to their own
Makefile boards are showing up twice in menuconfig
as $(eval $(call BuildImage)) was not dropped from
the new generic.mk.
Hence $(eval $(call BuildImage)) was being called
twice.
So, lets simply drop it from generic.mk.
Fixes: 378c7ff282 ("ipq40xx: split generic images into own file")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This enables the MikroTik platform driver, it enables us to parse
valuable info from hard_config including WLAN calibration data
extraction from sysfs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This enables the new MikroTik specific partition parser.
This avoids manually specifying the MikroTik specific partitions as they
can be detected by their magic values.
Signed-off-by: Robert Marko <robimarko@gmail.com>
MikroTik devices require the use of raw vmlinux out of the self
extracting compressed kernels.
They also require 4K sectors, kernel2minor, partition parser as well as
RouterBoard platform drivers.
So in order to not add unnecessary code to the generic sub target lets
introduce a MikroTik sub target.
Signed-off-by: Robert Marko <robimarko@gmail.com>
If the watchdog is enabled, set the timeout to 30 seconds before
decompress is started.
Mikrotik ipq40xx devices running with RouterBoot have the SoC watchdog
enabled and running with a timeout that does not allow time for the
kernel to decompress and manage the watchdog.
On ipq40xx RouterBoot TFTP boot the watchdog countdown is reset before:
Jumping to kernel
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
This adds a appended_dtb section to the ARM decompressor
linker script.
This allows using the existing ARM zImage appended DTB support for
appending a DTB to the raw ELF kernel.
Its size is set to 1MB max to match the zImage appended DTB size limit.
To use it to pass the DTB to the kernel, objcopy is used:
objcopy --set-section-flags=.appended_dtb=alloc,contents \
--update-section=.appended_dtb=<target>.dtb vmlinux
This is based off the following patch:
c063e27e02
Signed-off-by: Robert Marko <robimarko@gmail.com>
Both devices use u-boot env variables to boot OpenWrt from its flash
partition. Using u-boot envtools, it is possible to change the bootcmd
back to the stock firmware partition directly from OpenWrt without
attaching a serial cable or even physically accessing the device.
Signed-off-by: Jan Alexander <jan@nalx.net>
DTS files do not need to be executable. 644 is enough.
Fixes: 0fbdb51f76 ("ipq40xx: add Edgecore OAP-100 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[split by targets]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since updating the MDIO driver, the probe will fail hard on any
PHY not present on the bus, while this was not the case prior.
Fixes commit 26b1f72381 ("ipq40xx: net: phy: ar40xx: remove PHY
handling")
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: Reset
LED: Power, Internet
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER: On board with BLE module - by cp210x USB serial chip
On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
Lets use the generic upstream phy_print_status() instead of doing
something similar by hand.
Before:
ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=1000
After:
ess_edma c080000.edma eth1: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since we now have a proper PHY driver for QCA807x and AR803x has already
been supported properly there is no need for the driver to be poking
on PHY registers for ethtool ops.
So, lets simply use the generic
phy_ethtool_ksettings_get/phy_ethtool_ksettings_set functions.
This also has the advantage of properly populating stuff other than
speeds like, transceiver type, MDI-X etc.
ethtool before:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 4
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000000 (0)
Link detected: yes
ethtool after:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: Symmetric Receive-only
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 4
Transceiver: external
Auto-negotiation: on
MDI-X: off (auto)
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since the new PHY driver manages each PHY individually and therefore
registers each PHY that is marked with gpio-controller; DT property as a
GPIO controller we need to convert old DT bindings to account for this.
Only 2 boards use this so its not much of an issue.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This adds necessary DT properties for QCA807x PHY-s to IPQ4019 DTSI.
Also adds the PSGMII PHY as it wont get probed otherwise.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
PHY needs to be soft reset before starting it from ethernet driver as
AR40xx calibration will leave it in unwanted state.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since we now have proper PHY driver for the QCA807x PHY-s, lets remove
PHY handling from AR40xx.
This removes PHY driver, PHY GPIO driver and PHY init code.
AR40xx still needs to handle PSGMII calibration as that requires R/W
from the switch, so I am unable to move it into PHY driver.
This also converted the AR40xx driver to use OF_MDIO to find the MDIO
bus as it now cant be set through the PHY driver.
So lets depend on OF_MDIO in KConfig.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s.
They are 2 or 5 port IEEE 802.3 clause 22 compliant
10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s.
They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC,
while second one is SGMII for connection to MAC or fiber.
Both models have a combo port that supports 1000BASE-X and 100BASE-FX
fiber.
Each PHY inside of QCA807x series has 2 digitally controlled output only
pins that natively drive LED-s.
But some vendors used these to driver generic LED-s controlled by
user space, so lets enable registering each PHY as GPIO controller and
add driver for it.
This also adds the ability to specify DT properties so that 1000 Base-T
LED will also be lit up for 100 and 10 Base connections.
This is usually done by U-boot, but boards running mainline U-boot are
not configuring this yet.
These PHY-s are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x
boards.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
With the reworked MDIO driver, EDMA will fail to get the MII BUS as it
used the MII BUS stored inside the MDIO structure private data.
This obviously does not work with the modernized driver, so lets switch
to using a purpose build of_mdio_find_bus() which will return the MII
BUS and only requires the MDIO node to be passed.
This is easy as we already have the node parsed.
Also, since we now require OF_MDIO add that as dependency.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
IPQ40xx MDIO driver was upstreamed in kernel version 5.8.
So lets backport the upstream version and drop our local one.
This also refreshed the kernel config since the symbol name has changed.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8075 (2 ports)
PLC: MaxLinear G.hn 88LX5152
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET, WiFi, PLC Button
LEDS: red/white home, white WiFi
To modify a retail device to run OpenWRT firmware:
1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT
initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'.
2) Power on the device while pressing the recessed reset button next to
the Ethernet ports. This causes the bootloader to retrieve and start
the initramfs.
3) Once the initramfs is booted, the device will come up with IP
192.168.1.1. You can then connect through SSH (allow some time for
the first connection).
4) On the device shell, run 'fw_printenv' to show the U-boot environment.
Backup this information since it contains device unique factory data.
5) Change the boot command to support booting OpenWRT:
# fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm'
6) Change directory to /tmp, download the sysupgrade (e.g. through wget)
and install it with sysupgrade. The device will reboot into OpenWRT.
Notice that there is currently no support for booting the G.hn chip.
This requires userland software we lack the rights to share right now.
Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
Device specifications:
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3at POE+
+ used as WAN interface
* 12V 2A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio4:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio3:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3af/at POE(+)
+ used as WAN interface
* 12V/24V 1A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Other vendors are using functionality similar to the ones OpenMesh used to
implement two areas on the flash to store the default image and a fallback
image. So just change the name to dualboot_datachk.sh to avoid duplicated
code just to have the same script for different vendors.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Adjust spelling of vendor name to what is used in other places.
Also move definition in shared section.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts the usage of the S-Tag for separating LAN and WAN port on
the embedded switch. Many users complained about not being able to
manage C-Tag addition / removal on the switch as well as degraded
performance.
Fixes: commit 9da2b56760 ("ipq40xx: fix ethernet vlan double tagging")
Signed-off-by: David Bauer <mail@david-bauer.net>
The ASUS MAP-AC2200 suffers from a lower transmit/receive
signal power as compared to the stock firmware.
Upon investigation, it was discovered that stock firmware from
the GPL_MAP-AC2200_3.0.0.4.384.46249-g97d05bb.tar archive.
set the following GPIOs in "release/src/router/rc/init.c".
GPIO 44 and 46 have to be set to output high
GPIO 45 and 47 have to be set to output low
Here are some results, after activating the relevant
gpios through cmdline:
<https://forum.openwrt.org/t/asus-map-ac2200-low-transmit-receive-signal-5ghz/69005/12>
THX @ slh
Fixes: 9ad3967f14 ("ipq40xx: add support for ASUS Lyra")
Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
[slightly rewritten commit, added missing <>)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The OpenMesh related files were not updated since a while and the new
coding style requirements weren't integrated. This can cause problems
for new devices when an author uses these files as starting point.
* use SPDX-License-Identifiers instead of full license texts
* drop linux,default-trigger with value default-off for LEDs
* led nodes with label "abc:xyz" should have name "xyz_abc"
* led DT labels for "xyz_abc" should be "led_xyz_abc"
* "m25p80@0" flash node should be renamed to "flash@0"
* drop unnecessary empty lines
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[minor commit title and message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This pci@40000000 node from upstream was dropped when the device
was converted from local DTS(I) files to kernel patches in [1] to
ensure that change was purely cosmetic.
However, the DK04.1 has a PCI-E slot by default, so let's keep
(i.e. not remove) the kernel definition now.
[1] c4beac9ea2 ("ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1")
Suggested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A lot of patches are outdated versions of upstreamed patches and
drivers.
So lets pull in the upstreamed patches and reorder remaining ones.
This drops the unnecessary 721-dts-ipq4019-add-ethernet-essedma-node.patch
which adds nodes for not yet in OpenWrt IPQESS driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[do not touch 902-dts-ipq4019-ap-dk04.1.patch here]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This re-enables offloading features disabled by
commit 9da2b56760 ("ipq40xx: fix ethernet vlan double tagging").
Single-PHY devices use port-based VLANs on the switch, therefore no
S-TAG magic is involved here. Re-enabling these features restores
throughput back to 950 Mbit/s.
Reported-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: David Bauer <mail@david-bauer.net>
The target uses 5.4 as default kernel since 03/2020.
Kernel 4.19 support is not really maintained anymore, it does not
seem to be needed, and removing it will make upcoming driver
updates easier. Thus, remove it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The vDSO is used to accelerate some syscalls. It should work fine wherever it's
available, so enable it globally for all targets.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
There is no point in keeping the AR40xx driver as a patch as its
not pending merge or backport.
To allow for easier maintenance until DSA is ready move it into
files like EDMA is.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[combine with removal from patches-5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upstream provides DTS(I) files for IPQ4019/AP-DK04.1, but we overwrite
them with local versions so far.
Remove the local files and use patches to be closer to upstream.
We already do the same for IPQ40xx/AP-DK01.1-C1.
Technically, this changes the compatible from "qcom,ipq4019" to
"qcom,ipq4019-dk04.1-c1", but it has never been implemented correctly
beforehand anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds several stylistic and functional improvements of the recently
added Edgecore ECW5211, especially:
* Drop the local BDFs as those are already in the upstream under different names
* Add SPDX tag to DTS
* Add label MAC address
* Move LED trigger to DTS
* Remove unnecessary status="okay"
* Disable unused SS USB phy as the USB port only supports USB 2.0
* Make uboot-env partition writable
* Remove qcom,poll_required_dynamic property as the driver does not use it
* Tidy up the device recipe
Fixes: 4488b260a0 ("ipq40xx: add Edgecore ECW5211 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Robert Marko <robert.marko@sartura.hr>
Like in the previous patches for ath79 and ramips, this will remove
the "devicename" from LED labels in ipq40xx.
The devicename is removed in DTS files and 01_leds, and a migration
script is added. While at it, also harmonize capitalization of
wlan2G/wlan5G vs. wlan2g/wlan5g.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
Therefore, adding it to a DTS _and_ a DTSI file is actually wrong,
as it will be present twice then (though the compiler does not
complain about it).
In ipq40xx, the dts-v1 statement is already included in
qcom-ipq4019.dtsi, so we don't have to add it anywhere at all.
However, based on the conditions stated above, this requires
qcom-ipq4019.dtsi to be included as the first file in any DTS(I).
Consequently, this patch removes all cases of dts-v1 for the
ipq40xx target, and moves the includes accordingly where necessary.
While at it, remove a few obviously unneeded includes on the way.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
.dts:226.17-230.4: Warning (spi_bus_reg): /soc/spi@78b6000/spi@1:
SPI bus unit address format error, expected "0"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Linksys MR8300 is based on QCA4019 and QCA9888
and provides three, independent radios.
NAND provides two, alternate kernel/firmware images
with fail-over provided by the OEM U-Boot.
Hardware Highlights:
SoC: IPQ4019 at 717 MHz (4 CPUs)
RAM: 512MB RAM
SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs)
RAM: 512M DDR3
FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks)
BTN: Reset and WPS
USB: USB3.0, single port on rear with LED
SERIAL: Serial pads internal (unpopulated)
LED: Four status lights on top + USB LED
WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14
WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64
WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165
Support is based on the already supported EA8300.
Key differences:
EA8300 has 256MB RAM where MR8300 has 512MB RAM.
MR8300 has a revised top panel LED setup.
Installation:
"Factory" images may be installed directly through the OEM GUI using
URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1)
Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com>
[copied Hardware-highlights from EA8300. Fixed alphabetical order.
fixed commit subject, removed bogus unit-address of keys,
fixed author (used Signed-off-By to From:) ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band
wireless access point.
Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 2 MB SPI NOR
128 MB SPI NAND
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R integrated
Ethernet: 2x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus
LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU
Buttons: 1x GPIO controlled
EEPROM: 16 Kbit, compatible with AT24C16
UART: row of 4 holes marked on PCB as J19, starting count from the side
of J19 marking on PCB
1. GND, 2. RX, 3. TX, 4. 3.3V
baud: 115200, parity: none, flow control: none
The device supports OTA or USB flash drive updates, unfotunately they
are signed. Until the signing key is known, the UART access is mandatory
for installation. The difficult part is disassembling the casing, there
are a lot of latches holding it together.
Teardown
Prepare three thin, but sturdy, prying tools. Place the device with back
of it facing upwards. Start with the wall having a small notch. Insert
first tool, until You'll feel resistance and keep it there. Repeat the
procedure for neighbouring walls. With applying a pressure, one edge of
the back cover should pop up. Now carefully slide one of the tools to
free the rest of the latches.
There's no need to solder pins to the UART holes, You can use hook clips,
but wiring them outside the casing, will ease debuging and recovery if
problems occur.
Installation
1. Prepare TFTP server with OpenWrt initramfs image.
2. Connect to UART port (don't connect the voltage pin).
3. Connect to LAN port.
4. Power on the device, carefully observe the console output and when
asked quickly enter the failsafe mode.
5. Invoke 'mount_root'.
6. After the overlayfs is mounted run:
fw_setenv bootdelay 3
This will allow to access U-Boot shell.
7. Reboot the device and when prompted to stop autoboot, hit any key.
8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
'setenv' to do that, then run following commands:
tftpboot 0x84000000 <openwrt_initramfs_image_name>
bootm 0x84000000
and wait till OpenWrt boots.
9. In OpenWrt command line run following commands:
fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000"
fw_setenv bootcmd "run openwrt"
10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
with:
ubirmvol /dev/ubi0 -N ubi_rootfs
sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name>
11. After flashing, the access point will reboot to OpenWrt, then it's
ready for configuration.
Reverting to OEM firmware
1. Execute installation guide steps: 1, 2, 3, 7, 8.
2. In OpenWrt command line run following commands:
ubirmvol /dev/ubi0 -N rootfs_data
ubirmvol /dev/ubi0 -N rootfs
ubirmvol /dev/ubi0 -N kernel
ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs
ubimkvol /dev/ubi0 -S 34 -N kernel1
ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1
ubimkvol /dev/ubi0 -S 264 -N rootfs_data
fw_setenv bootcmd bootipq
3. Reboot.
Known issues
The LEDs ring doesn't have any dedicated driver or application to control
it, the only available option atm is to manipulate it with 'i2cset'
command. The default action after applying power to device is spinning
blue light. This light will stay active at all time. To disable it
install 'i2c-tools' with opkg and run:
i2cset -y 2 0x48 3 1 0 0 i
The light will stay off until next cold boot.
Additional information
After completing 5. step from installation guide, one can disable asking
for root password on OEM firmware by running:
sed -e 's/root❌/root::/' -i /etc/passwd
This is useful for investigating the OEM firmware. One can look
at the communication between the stock firmware and the vendor's
cloud servers or as a way of making a backup of both flash chips.
The root password seems to be constant across all sold devices.
This is output of 'led_ctl' from OEM firmware to illustrate
possibilities of LEDs ring:
Usage: led_ctl [status | upgrade | force_upgrade | version]
led_ctl solid COLOR <brightness>
led_ctl single COLOR INDEX <brightness 0 - 15>
led_ctl spinning COLOR <period 1 - 16 (lower = faster)>
led_ctl fill COLOR <period 1 - 16 (lower = faster)>
( default is 5 )
led_ctl flashing COLOR <on dur 1 - 128> <off dur 1 - 128>
(default is 34) ( default is 34 )
led_ctl pulsing COLOR
COLOR: red, green, blue, yellow, purple, cyan, white
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit,
changed ubi volumes for easier integration, slightly reworded
commit message, changed ubi volume layout to use standard names all
around]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All modifications made by update_kernel.sh/no manual intervention needed
Run-tested: ipq806x (R7800), ath79 (Archer C7v5), x86/64
No dmesg regressions, everything appears functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add run test from PR]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The ethernet ports on the AVM FRITZRepeater 3000 are not separated
between LAN and WAN in the stock firmware. OpenWrt currently abstracts
port 4 as eth0 and port 5 as eth1, bridging them in the kernel.
This patch adjusts the GMAC port bitmasks and default bitmask for ar40xx
to bridge them on the switch, avoiding traffic on both ports to pass
thru the CPU.
Signed-off-by: David Bauer <mail@david-bauer.net>
flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
- tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
- ubiattach -p /dev/mtd0
- ubirmvol /dev/ubi0 -n0
- ubirmvol /dev/ubi0 -n1
- ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
- sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin
Signed-off-by: John Crispin <john@phrozen.org>
This patch adds support for the Edgecore ECW5211 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7
- RAM: 256MB DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB MX35LFxGE4AB SPI-NAND
- Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn)
- CC2540 BLE connected to USB 2.0 port
- Atmel AT97SC3205T I2C TPM
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Enable the VLAN tag offloading mechanism for RGMII single-port devices.
This allows those devices to use 802.1Q VLANs on the ethernet port.
Previously, RX frames were double tagged, as the RX TAG removal flag was
not enabled and an additional 802.1Q header was inserted elsewhere in
the code.
On the TX side, tagging was completely not present for single-port
devices. Enable tagging if an 802.1Q frame should be transmitted and
disable the default tagging mechanism for single-port devices.
Tested on Aruba AP-303
Signed-off-by: David Bauer <mail@david-bauer.net>
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.
Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Refresh config with make kernel_oldconfig.
After d1a8217d87 ("kernel: clean-up build-configurable kernel
config symbols"), the routine wants to add an additional
CONFIG_CGROUPS (=n), which has been removed manually again, as
this seems unintended.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
update_kernel.sh refreshed all patches, no human interaction was needed
Build system: x86_64
Run-tested: Netgear R7800 (ipq806x)
Signed-off-by: John Audia <graysky@archlinux.us>
As the the SoC uses implicit vlan tagging for dual MAC support, the
offload feature breaks when using double tagging.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: John Crispin <john@phrozen.org>
Commit e53ec043ba ("kirkwood: move usb support to modules") has moved
this config symbol into generic configs, so it could be removed from
other configs.
Suggested-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The patches for arch/arm/boot/dts/Makefile have not been updated
in a syntactically correct way (just body was changed). Fix it.
Fixes: 4a77a060ab ("ipq40xx: add support for Buffalo WTR-M2133HP")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.
Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A
Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
# ubidetach -p /dev/mtd15
# ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
# fw_setenv bootcmd bootipq
8. Perform reboot.
Recover to stock firmware
-------------------------
1. Execute the following command.
# fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Specifications:
SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM: 512 MiB
FLASH1: 16 MiB NOR - SPI0
FLASH2: 8 GiB eMMC
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT: Reset, WPS
LED: Power, Mesh, WLAN
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2: On board with BLE module
SPI1: On board socket for Zigbee module
Install via tftp
- NB: need to flash transition image firstly
Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf
Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Run tested: ath79
Build tested: ath79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.
Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (qcom-ipq4018-emr3500.dts), which is only
present for 5.4.
Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory.
If there ever was a new kernel with substantial DTS changes, a
new folder would need to be introduced anyway and could easily be
done.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The ZyXEL NBG6617 has a separate kernel partition which is 4MiB large.
Add the kernel size to validate the kernel won't be bigger than this
fixed limit.
Signed-off-by: David Bauer <mail@david-bauer.net>
The NETGEAR EX61500v2 and EX6150v2 U-Boot does not support booting LZMA
compressed images. Currently, they are using GZIP compressed kernels,
which results in ledd flash being available to the root and overlay
filesystems.
Using a zImage results in a smaller kernel and therefore increases
available space for rootfs and overlayfs.
Size reduced: ~1.1 MiB
Signed-off-by: David Bauer <mail@david-bauer.net>
ipq40xx is still using swconfig based switch management. This might
change in he future, however disable the DSA and Switchdev support for
now.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[rephrased commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072 (2 ports)
USB: 1 x 2.0 (Host controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: White, Blue, Red, Orange
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMR3500. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img
4. Flash the firmware
(IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
(IPQ40xx) # reset
Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[squashed update patch, updated to 5.4, dropped BOARD_NAME,
migrated to SOC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It was noticed that the the whole MAC can hang when transferring data from
one ar40xx port (WAN ports) to the CPU and from the CPU back to another
ar40xx port (LAN ports). The CPU was doing only NATing in that process.
Usually, the problem first starts with a simple data corruption:
$ wget https://cdimage.debian.org/debian-cd/current/amd64/iso-cd/debian-10.4.0-amd64-netinst.iso -O /dev/null
...
Connecting to saimei.ftp.acc.umu.se (saimei.ftp.acc.umu.se)|2001:6b0:19::138|:443... connected.
...
Read error at byte 48807936/352321536 (Decryption has failed.). Retrying.
But after a short while, the whole MAC will stop to react. No traffic can
be transported anymore from the CPU port from/to the AR40xx PHY/switch and
the MAC has to be resetted.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: John Crispin <john@phrozen.org>
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM0
ETH: Atheros AR8035
LED: System (red / green / amber)
BTN: Reset
The USB port on the device is (in contrast to other Aruba boards) real
USB. The AP uses a CP2101 USB TTY converter on the board.
Console baudrate is 9600 8n1.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the ethernet port of the access point.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device.
6. Flash OpenWrt:
Make sure you use the mtd partition with the label "ubi" here!
$ ubidetach -p /dev/mtd1
$ ubiformat /dev/mtd1
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated
QMI mPCIE modem.
This is stripped version of ASKEY RTL0030VW.
Hardware:
Specification:
-CPU: IPQ4019
-RAM: 256MB
-Flash: NAND 128MB + NOR 16MB
-WiFi: Integrated bgn/ac
-LTE: mPCIe card (Modem chipset MDM9230)
-LAN: 2 Gigabit Ports
-USB: 2x USB2.0
-Serial console: RJ-45 115200 8n1
-Unsupported VoIP
Known issues:
None so far.
Instruction install:
There are two methods: Factory web-gui and serial + tftp.
Web-gui:
1. Apply factory image via stock web-gui.
Serial + initramfs:
1. Rename OpenWrt initramfs image to "image"
2. Connect serial console (115200,8n1)
3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4.
4. U-Boot commands:
sf probe && sf read 0x80000000 0x180000 0x10000
setenv serverip 192.168.1.4
set fdt_high 0x85000000
tftpboot 0x84000000 image
bootm 0x84000000
5. Install sysupgrade image via "sysupgrade -n"
Back to stock:
All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0,
do firstboot and factory reset with OFW:
1. read mtd8:
dd if=/dev/mtd8 of=/tmp/mtd8
2. go to tmp:
cd /tmp/
3. write first part of partition:
dd if=mtd8 of=mtd8.new bs=1 count=76
4. check which layout uses bootloader:
cat /proc/mtd
5a. If first are kernel_1 and rootfs_1 write 0:
echo -n -e '\x00' >> mtd8.new
5b. If first are kernel and rootfs write 1:
echo -n -e '\x01' >> mtd8.new
6. fill with rest of data:
dd if=mtd8 bs=1 skip=77 >> mtd8.new
7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with:
hexdump mtd8.new
8. write new mtd8 to flash:
mtd write mtd8.new /dev/mtd8
9. do firstboot
10.reboot
11. Do back to factory defaults in OFW GUI.
Based on work: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019
Specification:
SoC/Wireless: QCA IPQ4019
RAM: 512MiB
Flash: 128MiB SLC NAND
Ethernet PHY: QCA8075
Ethernet ports: 1x WAN, 2x LAN
LEDs: 7 LEDs
2 (USB, CAN) are GPIO
other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register
Button: Reset
Flash instruction:
Disassemble the router, connect UART pins like this:
GND TX RX
[x x . . x .]
[. . . . . .]
(QCA8075 and IPQ4019 below)
Baud-rate: 115200
Set up TFTP server: IP 192.168.1.188/24
Power on the router and interrupt the booting with UART console
env backup (in case you want to go back to stock and need it there):
printenv
(Copy the output to somewhere save)
Set bootenv:
setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs'
setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1'
setenv cm520_boot 'run set_ubi; run bootkernel'
setenv bootcmd 'run cm520_boot'
setenv bootargs
saveenv
Boot initramfs from TFTP:
tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb
bootm
After initramfs image is booted, backup rootfs partition in case of reverting to stock image
cat /dev/mtd12 > /tmp/mtd12.bin
Then fetch it via SCP
Upload nand-factory.ubi to /tmp via SCP, then run
mtd erase rootfs
mtd write /tmp/*nand-factory.ubi rootfs
reboot
To revert to stock image, restore default bootenv in uboot UART console
setenv bootcmd 'bootipq'
printenv
use the saved dump you did back when you installed OpenWrt to verify that
there are no other differences from back in the day.
saveenv
upload the backed up mtd12.bin and run
tftpboot mtd12.bin
nand erase 0xb80000 0x7480000
nand write 0x84000000 0xb80000 0x7480000
The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead
In case of this, set it back to rootfs:
cd /tmp
cat /dev/mtd7 > mtd7.bin
echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4
for i in 28 48 68 108; do
dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i
done
mtd write mtd7.bin BOOTCONFIG
mtd write mtd7.bin BOOTCONFIG1
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[renamed volume to ubi to support autoboot,
as per David Lam's test in PR#2432]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This symbol had been enabled in the initial device support submission
for kernel 4.14, but apparently got lost during the v4.19 port.
The ASUS Lyra MAP-AC2200 has a single (very bright) rgb LED, which is
controlled by the TI/National LP5523/55231 LED driver chip. It is left
enabled in a pulsating infinite rainbow loop by the bootloader,
expecting it to be reconfigured (disabled by default) after the boot
process has finished and is also required to indicate failsafe/
firstboot conditions.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Albert has reported, that his DAP-2610 wont boot with the latest
snapshot and Fredrik has found out, that the device gets stuck at
"Waiting for root device ..." due to missing 5.4 kernel config symbol
CONFIG_MTD_SPLIT_WRGG_FW which was probably lost during the kernel
version bump.
Ref: https://forum.openwrt.org/t/dap-2610-bricked-help-needed
Fixes: 272e0a702a ("ipq40xx: add v5.4 support")
Suggested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The bootloader does not always initialize the MDIO pins before booting
Linux. E.g. on version "U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Jul
25 2017 - 11:36:26)" this is the case when booting automatically without
activating the U-Boot console.
Without this change, the kernel boot will complain about missing PHYs:
libphy: ipq40xx_mdio: probed
ar40xx c000000.ess-switch: Probe failed - Missing PHYs!
libphy: Fixed MDIO Bus: probed
With this change it will work as expected:
libphy: ipq40xx_mdio: probed
ESS reset ok!
ESS reset ok!
libphy: Fixed MDIO Bus: probed
Ref: GH-2835
Tested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit description from Fredrik, subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.
For ramips, remove redundant values already present in parent file.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This new symbol popped up in few places. Disable it in generic config.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fixed merge conflict in generic/config-5.4]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.
Lets make it clear, that it is solely a community doing the maintenance
tasks.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
In 5.4 kernel old u32 array way of setting network features was dropped and linkmode is now the only way.
So lets migrate the EDMA driver to support linkmode.
Also, old get/set settings API for ethtool is also dropped so lets convert to new ksettings API while at it as it demands linkmode.
Now, gigabit works properly as well as ethtool.
Previously you would get this in ethtool:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000000 (0)
Link detected: yes
Now, features are properly advertised:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 4
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In 5.4 kernel old u32 array way of setting network features was dropped and linkmode is now the only way.
So lets migrate the PHY driver to support linkmode.
Also, now in order for gigabit to work, PHY driver needs to advertise PHY_GBIT_FEATURES instead of PHY_BASIC_FEATURES
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
of_get_mac_address returns valid pointer or ERR_PTR since 5.2 via commit
d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") so the
patch fixes following OOPs on nbg6617:
Unable to handle kernel paging request at virtual address ffffffed
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.4.24 #0
PC is at edma_axi_probe+0x444/0x1114
LR is at bus_find_device+0x88/0x9c
Where the PC can be resolved to:
>>> l *edma_axi_probe+0x444
0xc067be5c is in edma_axi_probe (./include/linux/string.h:378).
>>> l *edma_axi_probe+0x43f
0xc067be57 is in edma_axi_probe (drivers/net/ethernet/qualcomm/essedma/edma_axi.c:936)
Which leads to the following code fragment:
935 mac_addr = of_get_mac_address(pnp);
936 if (mac_addr)
937 memcpy(edma_netdev[idx_mac]->dev_addr, mac_addr, ETH_ALEN);
Where using mac_addr=0xffffffed (-ENODEV) as source address in memcpy()
is causing the OOPs.
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Lets enable RAW NAND and Qcom NANDC drivers again in kernel 5.4.
They were dropped when 5.4 support was introduced due to upstream
changing the symbol names so refreshing was not enough.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[cut long line in commit message, enabled BCH as well]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch backports the upstream patch that adds the 4B_OPCODES flag to w25q256 under 4.19 kernel.
This is needed for ipq40xx and ramips.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Generate a cpximg that is compatible with the cpximg loader in Compex' u-boot.
The cpximg loader can be started either by holding the reset button during power
up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept an image
appropriate for the board revision that is etched on the board (e.g. 6A04).
The image can be pushed using tftp:
tftp -v -m binary 192.168.1.1 -c put openwrt-ipq40xx-generic-compex_wpj428-squashfs-cpximg-6a04.bin
cpximg files can also be used with the sysupgrade utility in stock images.
(add SSH key in luci for root access)
In mkmylofw_32m, the calculation of the "partition size" has been preferred
to just padding the partition as this will result in less block transfers
during flashing (while the additional complexity is bearable).
Signed-off-by: Leon M. George <leon@georgemail.eu>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the 8devices Habanero development board.
Specs are:
CPU: QCA IPQ4019
RAM: DDR3L 512MB
Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without)
WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2
WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2
Ethernet: 5x Gbit LAN (QCA 8075)
USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019)
MicroSD slot (Uses SD controller built into IPQ4019)
SDIO3.0/EMMC slot (Uses the same SD controller)
Mini PCI-E Gen 2.0 slot (Built into IPQ4019)
5x LEDs (4 GPIO controllable)
2x Pushbutton (1 is connected to GPIO, other to SoC reset)
LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support)
1x UART 115200 rate on J18
2x breakout development headers
12V DC Jack for power
DIP switch for bootstrap configuration
Installation instructions:
Since boards ship with vendors fork of OpenWrt sysupgrade can be used.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit finally adds support for the built in SD/MMC controller in IPQ4019 SoC.
Controller is supported by the upstream SDHCI-MSM driver with a minor clock setting patch.
Patch is special to the IPQ4019 and cannot be upstreamed.
LDO and SDHCI node are upstreamed, and LDO node is awaiting to be accepted.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This fixes a typo in the device string for MAC address setup in
02_network and corrects the indent in the device's DTS files.
While at it, move the aliases section before the keys section to
have it closer to the top of the file.
Fixes: a736d912e2 ("ipq40xx: add support for EnGenius EAP2200")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
