Commit Graph

353 Commits

Author SHA1 Message Date
Michal Cieslakiewicz
09f46c6b54 ath79: add support for Netgear WNR1000 v2
This patch adds ath79 support for Netgear WNR1000v2.
Router was previously supported by ar71xx target only.
Note: this is a 4_32 device with limited upgrade capabilities.

Specification
=============
  * Description: Netgear WNR1000 v2
  * Loader: U-boot
  * SOC: Atheros AR7240 (340 MHz)
  * RAM: 32 MiB
  * Flash: 4 MiB (SPI NOR)
	- U-boot binary: 256 KiB
	- U-boot environment: 64 KiB
	- Firmware: 3712 KiB
	- ART: 64 KiB
  * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
  * Wireless: 2.4 GHz b/g/n (Atheros AR9285)
  * USB: no
  * Buttons:
	- Reset
	- WiFi (rfkill)
	- WPS
  * LEDs:
	- Power (amber/green)
	- WAN (amber/green)
	- WLAN (blue)
	- 4 x LAN (amber/green)
	- WPS (green)
  * UART: 4-pin connector JP2, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 1A
  * MAC addresses: LAN on case label, WAN +1, WLAN +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_tiny=y
CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr1000-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-21 13:15:46 +02:00
Michal Cieslakiewicz
12719ce37a ath79: add support for Netgear WNR2000 v3
This patch adds ath79 support for Netgear WNR2000v3.
Router was previously supported by ar71xx target only.
Note: this is a 4_32 device with limited upgrade capabilities.

Specification
=============
  * Description: Netgear WNR2000 v3
  * Loader: U-boot
  * SOC: Atheros AR7241 (360 MHz)
  * RAM: 32 MiB
  * Flash: 4 MiB (SPI NOR)
	- U-boot binary: 256 KiB
	- U-boot environment: 64 KiB
	- Firmware: 3712 KiB
	- ART: 64 KiB
  * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
  * Wireless: 2.4 GHz b/g/n (Atheros AR9287)
  * USB: no
  * Buttons:
	- Reset
	- WiFi (rfkill)
	- WPS
  * LEDs:
	- Power (amber/green)
	- WAN (amber/green)
	- WLAN (blue)
	- 4 x LAN (amber/green)
	- WPS (green)
  * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 1A
  * MAC addresses: LAN on case label, WAN +1, WLAN +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_tiny=y
CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr2000-v3=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-21 13:15:19 +02:00
Michal Cieslakiewicz
d74324e407 ath79: WNR612v2: improve device support
This patch improves ath79 support for Netgear WNR612v2.
Router functionality becomes identical to ar71xx version.

Changes include:
* software control over LAN LEDs via sysfs
* correct MAC addresses for network interfaces
* correct image size in device definition
* dts: 'keys' renamed to 'ath9k-keys'
* dts: 'label-mac-device' set to eth1 (LAN)
* dts: formatting adjustments

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-21 13:15:05 +02:00
Michal Cieslakiewicz
69df7eb73d ath79: add LAN LEDs control bits for AR724x GPIO function pinmux
Currently AR724x pinmux for register 0x18040028 controls only JTAG disable bit.
This patch adds new DTS settings to control LAN LEDs and CLKs that allow
full software control over these diodes - exactly the same is done by ar71xx
target in device setup phase for many routers (WNR2000v3 for example).

'switch_led_disable_pins' clears AR724X_GPIO_FUNC_ETH_SWITCH_LED[0-4]_EN bits.
'clks_disable_pins' clears AR724X_GPIO_FUNC_CLK_OBS[1-5]_EN and
AR724X_GPIO_FUNC_GE0_MII_CLK_EN bits. These all should be used together, along
with 'jtag_disable_pins', to allow OS to control all GPIO-connected LEDs and
buttons on device.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-21 13:14:52 +02:00
Tomasz Maciej Nowak
1bc921f419 ath79: add support for Sitecom WLR-7100
Sitecom WLR-7100 v1 002 (marketed as X7 AC1200) is a dual band wireless
router.

Specification
SoC: Atheros AR1022
RAM: 64 MB DDR2
Flash: 8 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R QCA9882 integrated (connected to PCIe lane)
Ethernet: 5x 10/100/1000 Mbps QCA8337N
USB: 1x 2.0
LEDS: 4x GPIO controlled, 5x switch
Buttons: 2x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
      white triangle on PCB
      1. VCC 3.3V, 2. GND, 3. TX, 4. RX
      baud: 115200, parity: none, flow control: none

Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Toolbox > Firmware,
4. Browse for OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
   is ready for configuration.

Known issues
5GHz LED doesn't work

Additional information
When TX line on UART is connected, and board is switched on from power
off state, the DDR memory training may fail.
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), which may or may
not work with introduced images.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-10-21 13:01:10 +02:00
Daniel Gimpelevich
ee41b602a2 ath79: fix gigabit link pll-data for EX7300
The device did not appear to be reachable unless the connection were
forced to 100Mb or lower. Revert to previously working pll-data.

Also fix the phy-mode to represent the actual state needed for ethernet
to function.

Reported-by: Moritz Schreiber <moritz@mosos.de>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[add remark about phy-mode property]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-21 09:06:52 +02:00
Michal Cieslakiewicz
758a4d1766 ath79: add AR934x NAND Flash Controller driver
This patch contains updated driver for Atheros NAND Flash Controller
written originally by Gabor Juhos for ar71xx (aka 'ar934x-nfc').
ath79 version has adapted to work with kernel 4.19 and Device Tree.
It has also been renamed to 'ar934x-nand' to avoid confusion with
Near-Field Communication technology.
Controller is present on Atheros AR934x SoCs and required for accessing
internal flash storage on routers like Netgear WNDR4300.
This port preserves all NAND programming code while moving platform
configuration to Device Tree and replacing some kernel functions marked
for retirement by 4.19.
Suitable definition is included in 'ar934x.dtsi' ('nand@1b000200' section).

Most important changes to ar71xx version are:
* old kernel sections of code removed
* 'bool swap_dma' provided by platform data is now set by boolean DT
  property 'qca,nand-swap-dma'
* board-supplied (mach-*.c code) platform data removed - its elements
  become either unused, redundant or replaced by DT methods (like reset)
* IRQ is reserved by devm_request_irq() so free_irq() is not needed anymore
* calls to deprecated nand_scan_ident() + nand_scan_tail() function pair
  replaced by using recommended nand_scan() with attach_chip() callback
* ECC is set to hardware by default, can be overriden by standard DT
  'nand-ecc-*' properties (software Hamming or BCH are other options)

This driver has been successfully tested on Netgear WNDR4300 running
experimental ath79 OpenWrt master branch.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[add reset control]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-20 15:32:53 +02:00
Jeff Kletsky
f5c7fe2ff0 ath79: Clean up GL-AR300M DTS/DTSI inclusions
Modify GL-AR300M-Lite and GL-AR300M (NOR):

* Include qca9531_glinet_gl-ar300m.dtsi directly
  rather than qca9531_glinet_gl-ar300m-nor.dts

* Remove redundant inclusion of gpio.h and input.h

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-20 13:01:43 +02:00
Andreas Ziegler
07c1ddf522 ath79: add support for UniFi AC-LR
The Unifi AC-LR has identical hardware to the Unifi AC-Lite.
The antenna setup is different according to the vendor,
which explains the thicker enclosure.

Therefore, it is helpful to know the exact device variant,
instead of having "Ubiquiti UniFi-AC-LITE/LR".

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[fix legacy name in commit message; add old boardname to
SUPPORTED_DEVICES]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-15 18:13:54 +02:00
Roger Pueyo Centelles
bba6646b5c ath79: add support for COMFAST CF-E313AC
This patch adds support for the COMFAST CF-E313AC, an  outdoor wireless
CPE with two Ethernet ports and a 802.11ac radio.

Specifications:

 - QCA9531 SoC
 - 650/400/216 MHz (CPU/DDR/AHB)
 - 1x 10/100 Mbps WAN Ethernet, 48V PoE-in
 - 1x 10/100 Mbps LAN Ethernet, pass-through 48V PoE-out
 - 1x manual pass-through PoE switch
 - 64 MB RAM (DDR2)
 - 16 MB FLASH
 - QCA9886 2T2R 5 GHz 802.11ac, 23 dBm
 - 12 dBi built-in antenna
 - POWER/LAN/WAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1)

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI. Settings from the original firmware
 will be saved and restored on the new one, so a factory reset will be
 needed. To do so, once the new firmware is flashed, enter into failsafe
 mode by pressing the reset button several times during the boot
 process, while the WAN LED flashes, until it starts flashing faster.
 Once in failsafe mode, perform a factory reset as usual.

 Alternatively, the U-boot bootloader contains a recovery HTTP server
 to upload the  firmware. Push the reset button while powering the
 device on and keep it pressed for >10 seconds. The device's LEDs will
 blink several times and the recovery page will be at
 http://192.168.1.1; use it to upload the sysupgrade image.

Note:

 Four MAC addresses are stored in the "art" partition (read-only):
  - 0x0000: 40:A5:EF:AA:AA:A0
  - 0x0006: 40:A5:EF:AA:AA:A2
  - 0x1002: 40:A5:EF:AA:AA:A1
  - 0x5006: 40:A5:EF:AA.AA:A3 (inside the 5 GHz calibration data)

 The stock firmware assigns MAC addresses to physical and virtual
 interfaces in a very particular way:
  - eth0 corresponds to the physical Ethernet port labeled as WAN
  - eth1 corresponds to the physical Ethernet port labeled as LAN

  - eth0 belongs to the bridge interface br-wan
  - eth1 belongs to the bridge interface br-lan

  - eth0 is assigned the MAC from 0x0 (*:A0)
  - eth1 is assigned the MAC from 0x1002 (*:A1)

  - br-wan is forced to use the MAC from 0x1002 (*:A1)
  - br-lan is forced to use the MAC from 0x0 (*:A0)

  - radio0 uses the calibration data from 0x5000 (which contains
    a valid MAC address, *:A3). However, it is overwritten by the
    one at 0x6 (*:A2)

 This commit preserves the LAN/WAN roles of the physical Ethernet
 ports (as labeled on the router) and the MAC addresses they expose
 by default (i.e., *:A0 on LAN, *:A1 on WAN), but swaps the position
 of the eth0/eth1 compared to the stock firmware:
  - eth0 corresponds to the physical Ethernet port labeled as LAN
  - eth1 corresponds to the physical Ethernet port labeled as WAN

  - eth0 belongs to the bridge interface br-lan
  - eth1 is the interface at @wan

  - eth0 is assigned the MAC from 0x0 (*:A0)
  - eth1 is assigned the MAC from 0x1002 (*:A1)

  - br-lan inherits the MAC from eth0 (*:A0)
  - @wan inherits the MAC from eth1 (*:A1)

  - radio0's MAC is overwritten to the one at 0x6

This way, eth0/eth1's positions differ from the stock firmware, but
the weird MAC ressignations in br-lan/br-wan are avoided while the
external behaviour of the router is maintained. Additionally, WAN
port is connected to the PHY gmac, allowing to monitor the link
status (e.g., to restart DHCP negotiation when plugging a cable).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-10-13 20:34:57 +08:00
Adrian Schmutzler
273a6cb562 ath79: improve DTS for TP-Link Archer D50 v1
This addresses several issues in the DTS file:
- add diag LED support
- remove unused node names
- fix whitespace issues

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-06 22:42:30 +02:00
Adrian Schmutzler
929becbc2d ath79: fix whitespace issues in DTS files
This is the result of grepping/searching for several common
whitespace issues like double empty lines, leading spaces, etc.

This patch fixes them for the ath79 target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-06 21:28:49 +02:00
Jeff Kletsky
eba0db95b5 ath79: Restore GL.iNet GL-AR300M-Lite first-boot connectivity
The relationship between GMAC0 and GMAC1 and the kernel devices
eth0 and eth1 was reversed for many ath79 devices by commit 8dde11d521
ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi

The GL-AR300M-Lite is a single-port device, with the "LAN" port of the
GL-AR300M board unpopulated and its sole port now referenced as eth1,
as a result of commit 8dde11d521. The device was unreachable on
first boot or fresh config.

By changing &eth1 (GMAC1) to an MFD, GMAC0 is able to associate with
the phy and is known by the kernel as "eth0".

Thanks to Chuanhong Guo for the suggestion of "simple-mfd"

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-09-29 00:46:14 +02:00
Adrian Schmutzler
8961d2268e ath79: convert devices to interrupt-driven gpio-keys
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.

Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as
this one is using ath9k keys.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Karl Palsson <karlp@etactica.com>
Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
2019-09-22 18:28:11 +02:00
Dmitry Tunin
00ed75f47f ath79: add support of Netgear WNDR3800CH
Add support for the ar71xx supported Netgear WNDR3800CH to ath79.
The device is identical to WNDR3800 except NETGEAR_BOARD_ID.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-21 23:41:31 +02:00
Dmitry Tunin
edf1c6c67a ath79: DIR825B1 switch to gpio-keys
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2019-09-21 23:41:31 +02:00
Adrian Schmutzler
50fdc0374b ath79: provide label MAC address
This patch adds the label MAC address for several devices in
ath79.

Some devices require setting the MAC address in 02_network:

For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- alfa-network,ap121f
- avm,fritz300e
- ubnt-xm devices

For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- adtran,bsap1800-v2
- adtran,bsap1840
- dlink,dir-842-c1/-c2/-c3
- engenius,ecb1750
- iodata,etg3-r
- iodata,wn-ac1167dgr
- iodata,wn-ac1600dgr
- iodata,wn-ac1600dgr2
- iodata,wn-ag300dgr
- nec,wg800hp
- nec,wg1200cr
- trendnet,tew-823dru

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-19 23:43:27 +02:00
Keith Maika
4cb5f29625 ath79: add support for TP-Link Archer C59v2
Add ath79 support for Archer C59v2, previously supported by ar71xx.

TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB

Flash instruction:
  - via web UI:
    1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
    2. Login to router and open the Advanced tab
    3. Navigate to System Tools -> Firmware Upgrade
    4. Upload firmware using the Manual Upgrade form
  - via TFTP:
    1. Set PC to fixed ip address 192.168.0.66
    2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
       and rename it to tp_recovery.bin
    3. Start a tftp server with the file tp_recovery.bin in its root directory
    4. Turn off the router
    5. Press and hold Reset button
    6. Turn on router with the reset button pressed and wait ~15 seconds
    7. Release the reset button and after a short time
       the firmware should be transferred from the tftp server
    8. Wait ~30 second to complete recovery.

Signed-off-by: Keith Maika <keithm@aoeex.com>
2019-09-16 21:40:06 +02:00
Adrian Schmutzler
38ccacf99b ath79: move common definitions from Archer C58/C59 to common DTSI
The Archer C58/C59 have redundant LED and MAC address definitions
in their DTS files. This moves them to the parent DTSI file.

The patch already accounts for the upcoming Archer C59 v2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-16 21:40:06 +02:00
Karl Palsson
dadcd3dd98 ath79: eg200: enable status led usage
This enables using the "eTactica" LED during boot, to indicate failsafe,
and during upgrade, while still leaving the LED alone for normal
operation.  This brings the device more in line with how other devices
work, and makes the failsafe functionality easier to use and understand.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2019-09-15 22:56:09 +02:00
David Bauer
18fa749df8 ath79: fix UniFi AC LED mapping
The UniFi AC LED mapping is currently off. The blue/white LED are used
as WiFi indicators, while the vendor firmware does not feature WiFI
LEDs.

Instead, the LEDs are used to indicate the devices status. Align the LED
mapping to match the vendor firmware as good as possible.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-12 15:39:21 +02:00
Adrian Schmutzler
fbbb4eb8b4 ath79: add support for TP-Link WDR3500 v1
Hardware:
SoC:      AR9344
CPU:      560 MHz
Flash:    8 MiB
RAM:      128 MiB
WiFi:     Atheros AR9340 2.4GHz 802.11bgn
          Atheros AR9300 5GHz 802.11an
Ethernet: AR934X built-in switch, WAN on separate physical interface
USB:      1x 2.0

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
   wdr3500v1_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[removed stray newline]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-03 18:43:27 +02:00
Tomasz Maciej Nowak
c1db564cbc ath79: dts: fix ja76pf2 spi frequency
The frequency was filled acording the information from datasheet for
particular chip (Winbond 25Q128BVFG). Unfortunately this led to
coruption and introduced bad blocks on the chip. Reducing the frequency
to commonly used in ath79, made the board more stable and no new bad
blocks were spoted.

Fixes: b3a0c97 ("ath79: add support for jjPlus JA76PF2")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-09-01 00:12:02 +02:00
David Bauer
7b137e9df9 ath79: correct OCEDO Ursus phy-mode property
This fixes the previously incorrect phy-mode for the OCEDO Ursus GMAC0.

See 62abbd587d ("ath79: correct various phy-mode properties")
for more details.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 22:11:29 +02:00
Karl Pálsson
075c570cde ath79: etactica-eg200: fix restore button
The button is labelled reboot/restore in documentation, and has always
been used for that.  Naming it WPS has always been wrong.

Signed-off-by: Karl Pálsson <karlp@etactica.com>
[matched author to SoB]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-08-31 12:08:23 +02:00
Luochongjun
921675a2d1 ath79: add support for gl-ar750
This patch supports gl-ar750, which was previously supported by ar71xx.

Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 2xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Switch: 1x switch
- Button: 1x reset button
- LED: 3x LEDS (white)

Flash instruction:
Support for sysupgrade directive upgrades, as well as luci upgrades.

Signed-off-by: Luochongjun <luochongjun@gl-inet.com>
2019-08-24 08:55:33 +08:00
Adrian Schmutzler
95dfeabf26 ath79: create DTSI for ar9341 TP-Link devices
This patch creates a shared DTSI for the TP-Link devices based
on ar9341 as those share a lot of definitions.

While at it, change from gpio-keys-polled to gpio-keys, remove
unused pll-data and remove some inherited stuff, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-17 23:52:34 +08:00
Lim Guo Wei
e7ab1b5173 ath79: migrate TP-Link TL-MR3420v2 to ath79
Specifications:
- SoC: ar9341
- RAM: 32M
- Flash: 4M
- Ethernet: 5x FE ports
- WiFi: ar9341-wmac

Flash instruction:
Upload generated factory firmware on vendor's web interface.

This changes the key assignment compared to ar71xx support of this
device, since of the two keys on the device one is used as combined
Reset/WPS and the second one as WiFi on/off button.
Despite, the reset button required GPIO_ACTIVE_HIGH to work correctly.

Signed-off-by: Lim Guo Wei <limguowei@gmail.com>
[redo commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-08-17 23:52:34 +08:00
xixiao zheng
2ada2a5e5b ath79: add support for PISEN TS-D084
PISEN TS-D084 is an wireless router with a battery and integrated power
supply based on Atheros AR9331.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz (AR9331)
- 1x USB 2.0

Flash instruction:
 Upload generated factory image through web interface.

Signed-off-by: xixiao zheng <xixiaozheng64@gmail.com>
[wrap commit message, add flash instruction]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-08-17 23:52:34 +08:00
David Bauer
84c103509a ath79: use Power LED as System LED for TL-WR842Nv3
The TP-Link TL-WR842N v3 has a software-controllable Power LED. The WPS
LED is normally only used as a System LED, when the Power LED can't be
controlled by software.

Additionally, the Power LED is also the System LED for this board in
ar71xx.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-15 00:33:12 +02:00
Adrian Schmutzler
32144ba275 ath79: update DTS for TP-Link WDR3600/WDR4300 v1
This replaces gpio-export by gpio-hogs and switches buttons
to interrupt-driven gpio-keys.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-13 02:11:39 +02:00
Joan Moreau
9ed272fe95 ath79: add support for Comfast WR650AC v1/v2
This is a dual band 11a/11n router with 1x wan and 4x gig lan ports.

There are two versions of this router which can be identified through
the factory web interface, v1 has 128mb ram and a uboot size of 128k,
v2 has 256mb ram and a uboot size of 256k, the remaining hardware and
PCB markings are the same.

Short specification:

    SoC: Qualcomm Atheros QCA9558 - 720 MHz
    Switch: Atheros AR8327
    Second radio : Qualcomm Atheros QCA9880 802.11ac
    4 LAN/1 WAN 1000Mps Ethernet
    256 MB of RAM (DDR2)
    16 MB of FLASH
    3x2.4 GHz, 3x5GHz antennas

Steps to install :

Option A : Use vendor UI

Option B (if A is not working) :
(a) Download 'backup' from vendor UI and rename it backup.tar.gz
(b) Open the archive, and update the root password in /etc/shadow by
    '$1$9wX3HGfB$X5Sb3kqzzBLdKRUR2kfFd0'
(c) 'Restore' from the archive using the vendor UI. Root password is now
    'aaa'
(d) Scp the firwmware to the device:
    $ scp <openwrt-sysupgrade>.bin root@192.168.1.1:/
(d) ssh to the device and flash the firmware:
    $ cd /
    $ mtd -e firmware -r write <openwrt-sysupgrade>.bin firmware

Signed-off-by: Gareth Parker <gareth41@orcon.net.nz>
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
Signed-off-by: Joan Moreau <jom@grosjo.net>
[reformatted commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-09 17:07:07 +02:00
Joan Moreau
abbbecaa73 ath79: add support for Comfast E314N-v2
Taken code from https://patchwork.ozlabs.org/patch/884850/ that was never
pushed by the author, and adapted to ath79.

The Comfast E314N-V2 is a 2.4 GHz 2x2 radio with a built-in directional
antenna and a second Ethernet port - very similar to the Ubiquiti
NanoStation M2. The Ethernet port features a pass-through PoE capability,
enabled or disabled with a slide switch.

Specifications :
- System-On-Chip: Qualcomm/Atheros QCA9531
- CPU/Speed: 650 MHz
- Flash size: 8 MiB
- RAM: 64 MiB
- 2 Ethernet 1Gbp
- 1 reset button
- 1 switch to choose PoE from LAN or Wan. 48Vdc
- Wifi 2.4 Ghz (b/g/n)
- UART inside the box (3.3V, pins marked on the PCB)

Firmware can be flashed on these units by the following method:
1.) Apply power to the unit
2.) Immediately AFTER applying power, hold down the reset button
3.) The WAN, LAN, and wireless lights will flash - wait three seconds
    (three flashes) and then release the button.
4.) After a second, the lights will flutter quickly and the unit will be
    visible at 192.168.1.1. A web page will be available to enable quick
    and simple uploading and flashing of firmware.

During the boot process, these units also look for a tftp server at
192.168.1.10. If one is present, the firmware can be uploaded as a file
called firmware-auto.bin

Signed-off-by: Joan Moreau <jom@grosjo.net>
[wrapped commit message - fix commit title capitalization]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-09 07:49:21 +02:00
Chuanhong Guo
4d5dae2741 ath79: add support for PISEN WMB001N
Specifications:
- SoC: AR9341
- RAM: 64M
- Flash: 16M
- Ethernet: 1 * FE port
- WiFi: ar934x-wmac
- Sound: WM8918 DAC
         1 * 3.5mm headphone jack
         2 * RCA connectors for speakers
         1 * SPDIF out
- USB: 1 * USB2.0 port

Flash instruction:
 Upload generated factory image via vendor's web interface.

Notes:
A. Audio stuff:
 1. Since AR934x, all pins for peripheral blocks can be mapped to
    any available GPIOs. We currently don't have a PCM/I2S driver
    for AR934x so pinmux for i2s and SPDIF are bound to i2c gpio
    node. This should be moved into I2S node when a PCM/I2S driver
    is available.
 2. The i2c-gpio node is for WM8918. DT binding for it can't be added
    currently due to a missing clock from I2S PLL.

B. Factory image:
 Image contains a image header and a tar.gz archive.
 1. Header: A 288 byte header that has nothing to do with appended
    tarball. Format:
     0x0-0x7 and 0x18-0x1F: magic values
     0x20: Model number string
     0xFC: Action string. It's either "update" or "backup"
     0x11C: A 1 byte checksum. It's XOR result of 0x8-0x11B
    Firmware doesn't care about the rest of the header as long as
    checksum result is correct.
    The same header is used for backup and update routines so the
    magic values and model number can be obtained by generating a
    backup bin and grab values from it.
 2. Tarball: It contains two files named uImage and rootfs, which
    will be flashed into corresponding mtd partition.
 Writing a special utility that can only output a fixed binary
 blob is overkill so factory image header is placed under
 image/bin instead.

C. LED
 The wifi led has "Wi-Fi" marked on the case but vendor's firmware
 used it as system status indicator. I did the same in this device
 support patch.

D. Firmware
 Factory u-boot is built without 'savenv' support so it's impossible
 to change kernel offset. A 2MB kernel partition won't be enough in
 the future. OKLI loader is used here to migrate this problem:
  1. add OKLI image magic support into uImage parser.
  2. build an OKLI loader, compress it with lzma and add a normal
     uImage header.
  3. flash the loader to where the original kernel supposed to be.
  4. create a uImage firmware using OKLI loader.
  5. flash the created firmware to where rootfs supposed to be.
 By doing so, u-boot will start OKLI loader, which will then load
 the actual kernel at 0x20000.

 The kernel partition is 2MB, which is too much for our loader.
 To save this space, "mtd-concat" is used here:
  1. create a 64K (1 erase block) partition for OKLI loader and
     create another partition with the left space.
  2. concatenate rootfs and this partition into a virtual flash.
  3. use the virtual flash for firmware partition.

 Currently OKLI loader is flashed with factory image only.
 sysupgrade won't replace it. Since it only has one function
 and it works for several years, its unlikely to have some bugs
 that requires a replacement.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-08-08 21:00:59 +08:00
Perry Melange
796ad2f7ef ath79: add support for D-Link DIR-842 C3
Hardware spec of DIR-842 C3:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: circuit onboard, but components are not soldered

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or
   the u-boot failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted.
   Otherwise the u-boot will enter failsafe mode as the checksum
   of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the
   firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
   just upgrade the factory.bin through the u-boot failsafe interface
   and then goto step 2.

Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
2019-08-07 21:17:40 +02:00
Adrian Schmutzler
d7b4b5ec24 ath79: fix vendor capitalization of TP-Link
According to detective grep, with this patch all devices should
be labelled "TP-Link" consistently.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-07 18:04:03 +02:00
Adrian Schmutzler
854ab1b045 ath79: add support for TP-Link CPE220 v2
This seems to be identical to CPE210 v1 despite having removable
antennas.

Specifications:

    * SoC: Qualcomm Atheros AR9344 (560 MHz)
    * RAM: 64MB
    * Storage: 8 MB
    * Wireless: 2.4GHz N based built into SoC 2x2
    * Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:

Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-07 18:04:03 +02:00
Adrian Schmutzler
0104eed1e5 ath79: add support for TP-Link CPE510 v1
TP-Link CPE510-v1 is an outdoor wireless CPE for 5 GHz with
two Ethernet ports based on Atheros AR9334

Specifications:
 - 560/450/225 MHz (CPU/DDR/AHB)
 - 2x 10/100 Mbps Ethernet, 1x PoE-in, 1x PoE-out
 - 64 MB of DDR2 RAM
 - 8 MB of SPI-NOR Flash
 - 2T2R 5 GHz
 - 13 dBi built-in antenna
 - Power, LAN0, LAN1 green LEDs
 - 4x green RSSI LEDs

Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254

Based on the work of Paul Wassi <p.wassi@gmx.at>

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-07 18:04:03 +02:00
Adrian Schmutzler
08857e69be ath79: add support for TP-Link CPE210 v1
Specifications:

    * SoC: Qualcomm Atheros AR9344 (560 MHz)
    * RAM: 64MB
    * Storage: 8 MB
    * Wireless: 2.4GHz N based built into SoC 2x2
    * Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:

Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-07 18:04:03 +02:00
Adrian Schmutzler
9ba83c450c ath79: provide common DTSI for CPE510 v2/v3 and CPE610
This puts some common code into a new shared DTSI. Common nodes
are chosen so that the new DTSI can be used for CPE210 v1, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-07 18:04:03 +02:00
Adrian Schmutzler
c02b9818a5 ath79: add support for TP9343-based TP-Link TL-WR94x devices
This adds support for several TP-Link devices based on TP9343
("a QCA9561 without PCIe and USB"):
- TL-WR940N v3
- TL-WR940N v4
- TL-WR941ND v6

The devices are only different concerning LEDs and MAC address
assignment.

All TL-WR940 are with non-detachable antennas (N), all
TL-WR941 devices are with detachable antennas (ND).

Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to * (see below)
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

* TFTP image names:
940 v3: wr941ndv6_tp_recovery.bin
940 v4: wr940nv4_tp_recovery.bin
941 v6: wr941ndv6_tp_recovery.bin

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-05 21:50:15 +02:00
Jackson Lim
030fc6ab6c ath79: add support for D-Link DIR-842 C1
Hardware spec of DIR-842 C1:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: circuit onboard, but components are not soldered

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or
   the u-boot failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted.
   Otherwise the u-boot will enter failsafe mode as the checksum
   of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the
   firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
   just upgrade the factory.bin through the u-boot failsafe interface
   and then goto step 2.

Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
[fix whitespace issues]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-05 10:54:11 +02:00
Adrian Schmutzler
8b76c6695b ath79: add support for TP-Link TL-WR841N/ND v12
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same
FCC ID, same TFTP image name...).

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to wr841nv11_tp_recovery.bin
   (it's really v11, not v12)
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-05 10:54:11 +02:00
Adrian Schmutzler
4254193c1d ath79: add support for TP-Link TL-WR841N/ND v10
The TL-WR841N/ND v10 is mostly identical to the v9. Apart from some minor
changes, it contains a newer revision of the QCA9533 SoC and the CPU clock
is significantly higher.

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to wr841nv10_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-05 10:54:11 +02:00
Piotr Dymacz
5e9086b7b1 ath79: fix SOC version in compat string for A770
YunCore A770 is based on QCA9531, not QCA9533.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-07-31 08:38:06 +02:00
Roger Pueyo Centelles
334bbc5198 ath79: add support for ALFA Network AP121F
This commit ports support for the ALFA Network AP121F, a pocket-size
router with 1 Ethernet and 2.4 GHz WiFi based on the AR9331 SoC, to the
ath79 target (it was already supported in ar71xx; see commit 0c6165d2
for more details).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[pepe2k@gmail.com: fixed GPIO polarity, included USB support, changed
DTS nodes order, moved WLAN LED trigger define to DTS, made U-Boot env
partition writable]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-07-31 08:38:01 +02:00
Adrian Schmutzler
a421f33316 ath79: fix indent in TP-Link TL-WR842N v3 DTS file
Convert leading spaces to tab to match rest of the file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-30 00:34:39 +02:00
David Bauer
5897b2be21 ath79: remove lines-initial-states property
The lines-initial-states property was an early attempt to set the latch
bit of the shift register on driver probe. It is not implemented in the
driver and was rejected upstream. The latch bit was always set by a GPIO
hog, so this property is safe to drop.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-25 17:27:57 +02:00
Jackson Lim
209b368254 ath79: add support for D-Link DIR-842 C2
Hardware spec of DIR-842 C2:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: 2.0

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or
   the u-boot failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted.
   Otherwise the u-boot will enter failsafe mode as the checksum
   of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the
   firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
   just upgrade the factory.bin through the u-boot failsafe interface
   and then goto step 2.

Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
[Reword reset-hog comment, fix formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-24 11:36:02 +02:00
INAGAKI Hiroshi
d616b2c906 ath79: modify device name of I-O DATA WN-AC1600DGR2
The hardware of I-O DATA WN-AC1600DGR3 has completely compatibility
with WN-AC1600DGR2, so modify the device name of WN-AC1600DGR2 to show
the images for DGR2 also support DGR3.

Specification of WN-AC1600DGR3:

- SoC        : Qualcomm Atheros QCA9557
- RAM        : DDR2 128 MiB
- Flash      : SPI-NOR 16 MiB
- WLAN       : 2.4/5 GHz
  - 2.4 GHz  : QCA9557 (SoC), 2T2R
  - 5 Ghz    : QCA9880, 3T3R
- Ethernet   : 5x 10/100/1000 Mbps
  - Switch   : QCA8337N
- LEDs/Input : 6x/6x (4x buttons, 1x slide-switch)
- UART       : through-hole on PCB
  - J1: Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-07-18 00:06:55 +02:00