Commit Graph

3974 Commits

Author SHA1 Message Date
Daniel Golle
f625d9b31c ramips: mt76x8: add missing model string to Yuncore CPE200
Add missing 'model' string to DT, so /tmp/sysinfo/model gets populated.

Fixes: 64dae1052b ("ramips: mt76x8: add support for Yuncore CPE200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-09-11 00:17:05 +02:00
John Audia
15280316fa kernel: bump 6.6 to 6.6.50
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.50

All patch automatically rebased.

Test version: r27317-8e6543fae5
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16351
Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-09-08 21:29:13 +02:00
Rosen Penev
8e6543fae5 ramips: pinctrl-aw9523: update to current upstream
Various cleanups and bugfixes were applied.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16215
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-09-07 22:27:01 +02:00
Daniel Golle
64dae1052b ramips: mt76x8: add support for Yuncore CPE200
Yuncore CPE200 is an outdoor unit with IEEE 802.11ac radio.

Hardware:
 - SoC: MediaTek MT7628DAN (MIPS 580MHz)
 - Flash: 8 MiB Spansion S25FL064K
 - RAM: 64 MiB (built-into SoC)
 - WLAN: 5 GHz (MT7613AE)
 - Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
 - Buttons: 1 Reset button, 2 buttons for display UI (unsupported)
 - LEDs: 4x Green (Power, LAN, WAN, WiFi)
 - Display: 4 digit 7-segment display driven by an additional
            microcontroller (unsupported)
 - Serial console: unpopulated header, 57600 8n1 (RX only)
 - Power: 12 VDC, 1 A

Installation:
The installation can be done via the recovery HTTP server which is built
into the bootloader. Hold down the reset button while connecting the
device to power and keep holding a bit more than 3 seconds. Connect to
http://192.168.0.100/ and upload sysupgrade.bin file.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-09-02 13:27:47 +02:00
Goetz Goerisch
3774f3272e treewide: rename ZyXEL to Zyxel
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.

This commit aligns the casing of Zyxel everywhere.

Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-08-25 15:08:25 +02:00
Rosen Penev
4f2dadcf95 ramips: mt7621_nand: don't set owner
Found with coccinelle:

No need to set .owner here. The core will do it.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16217
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-08-25 13:14:07 +02:00
John Audia
3eb08538c4 kernel: bump 6.6 to 6.6.46
This commit makes three changes all needed for the update of the 6.6 kernel.

1. Upstream kernel bump to 6.6.46

	Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.46
	Manually rebased:
        	bcm27xx/patches-6.6/950-0320-spi-spidev-Restore-loading-from-Device-Tree.patch
	All other patches automatically rebased.

2. Adjusted the following for new ksym[1] enabling it:

        armsr/config-6.6
        bcm27xx/bcm2712/config-6.6

3. Added a fix to receiving fraglist GSO packets:

	generic/pending-6.6/601-udp-fix-receiving-fraglist-GSO_packets.patch[2]

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v6.6.46&id2=v6.6.45
2. https://marc.info/?l=linux-netdev&m=172407994500599&w=2

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16173
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-08-20 23:41:08 +02:00
Rosen Penev
40452223d6 ramips: ethernet: use devm for request_irq
Allows removing free_irq. Simpler.

Oddly enough the other switch code already does this.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16050
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-08-19 10:45:06 +02:00
Daniel Golle
e497c975d3 ramips: mt76x8: add support for Yuncore M300
Hardware:
 - SoC: MediaTek MT7628DAN (MIPS 580MHz)
 - Flash: 8 MiB Spansion S25FL064K
 - RAM: 64 MiB (built-into SoC)
 - WLAN: 2.4 GHz (MT7628)
 - Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
 - Buttons: 1 Reset button
 - LEDs: 1x Red, 1x Green
 - Serial console: unpopulated header, 57600 8n1 (RX only)
 - Power: 12 VDC, 1 A

There are unpopulated areas on the board for 5 GHz WiFi via PCIe as well
as (most likely) Quectel EG25-G 4G module. As both are not populated on
my board support for both is missing for now.

Installation:
The installation can be done via the recovery HTTP server which is built
into the bootloader. Hold down the reset button while connecting the
device to power and keep holding a bit more than 3 seconds. Connect to
http://192.168.188.253/ and upload sysupgrade.bin file.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-08-15 03:19:30 +01:00
Anton Stratonnikov
f51cb74473 ramips: add support for Xiaomi R4AC v2 (intl)
The second edition of international version of Mi Router 4A 100M is
very similar to the non-international one, but has another wireless chip.

 Installation
--------------

1. Initialize build-in firmware (use webgui for 192.168.31.1)
  You should install root password

2. Run OpenWRTInvasion for the first time (probably it will fail)
  Version 0.0.10 is working as well as 0.0.1.

3. Run OpenWRTInvasion for the second time
  It will create an access to your router

4. Upload sysupgrade image to router (/tmp/fw.bin)
  pc# nc -l 8080 < …/ramips/mt76x8/…-100m-intl-v2-squashfs-sysupgrade.bin
  router# nc 192.168.31.175 8080 > /tmp/fw.bin

5. Flash new firmware
  router# run mtd -r write /tmp/fw.bin OS1

6. Check result
  Wait about 5-10 minutes after flash. Router should reboot itself and
  turn left led from orange to blue.

In case of failure one can use Xiaomi 4a 100m debrick tool
(it uploads special image via tftpd in recovery mode)
After that you can start again from step 1.

Another actions are very similar to original Mi Router 4A 100M

 Original mtd paritions:
-------------------------

```
Creating 9 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000020000 : "Bootloader"
0x000000020000-0x000000030000 : "Config"
0x000000030000-0x000000040000 : "Factory"
0x000000040000-0x000000050000 : "crash"
0x000000050000-0x000000060000 : "cfg_bak"
0x000000060000-0x000000160000 : "overlay"
0x000000160000-0x000000dc0000 : "OS1"
0x000000dc0000-0x000001000000 : "disk"
with special sub-partition
0x0000002c0000-0x000000dc0000 : "rootfs"
```

We will use OS1+disk space:
```
0x000000160000-0x000001000000 : "firmware"
```

Co-authored-by: Nita Vesa <nita.vesa@elektrik.link>
Signed-off-by: Anton Stratonnikov <billic@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/14304
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-08-13 00:48:06 +02:00
Rosen Penev
11403697c9 ramips: mt7621_nand: use clk_get_optional_enabled
Simplifies the code by removing clk_disable_unprepare.

Also removed gotos and used dev_err_probe.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16133
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-08-12 19:40:48 +02:00
John Audia
b733b6acb5 kernel: bump 6.6 to 6.6.44
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.44

Removed upstreamed:
	rockchip/patches-6.6/044-v6.11-arm64-dts-rockchip-Add-sdmmc-related-properties-on-r.patch[1]
	rockchip/patches-6.6/045-v6.11-arm64-dts-rockchip-Add-pinctrl-for-UART0-to-rk3308-r.patch[2]
	rockchip/patches-6.6/046-v6.11-arm64-dts-rockchip-Add-mdio-and-ethernet-phy-nodes-t.patch[3]
	rockchip/patches-6.6/048-v6.11-arm64-dts-rockchip-Update-WIFi-BT-related-nodes-on-r.patch[4]
	rockchip/patches-6.6/310-PCI-dw-rockchip-Fix-initial-PERST-GPIO-value.patch[5]

Manually rebased:
	bcm27xx/patches-6.6/950-0526-mfd-Add-rp1-driver.patch
	ramips/patches-6.6/810-uvc-add-iPassion-iP2970-support.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.44&id=96155dc8c99e76a0e58932ca5f88148a37af3617
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.44&id=30ee9e5ecc5fd6854a1690ab11e6e6b4851ac9ab
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.44&id=0c4c1b7daf23bccf0da5b65b3cd5b32bfa5a5af4
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.44&id=a86a5685675834732789df202e73153db59d8dcc
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.44&id=a30211c6704899de0616ac0f97601122d899c86d

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16061
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-08-06 00:40:42 +02:00
Mieczyslaw Nalewaj
c0e50ebaf7 kernel: rtl8367b: use realtek,extif property
Use realtek,extif property instead of realtek,extif0 to extif2
by extending it with the cpu_port parameter.
The extif number is automatically calculated based on cpu_port.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-08-06 00:34:14 +02:00
Mieczyslaw Nalewaj
343f4f3c54 kernel: rtl8367: use realtek,extif property
Use realtek,extif property instead of realtek,extif0 and realtek,extif1
by extending it with the cpu_port parameter.
The extif number is automatically calculated based on cpu_port.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-08-06 00:34:14 +02:00
Shiji Yang
901adc3f2f ramips: fix PCIe reset pins for MTC WR1201
This router has two reset pins, GPIO 8 and GPIO 19. We have to
configure them correctly to ensure that the wireless NICs work
properly.

Fixes: https://github.com/openwrt/openwrt/issues/11736
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16009
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-29 01:09:24 +02:00
Shiji Yang
27510dc01b ramips: create shared dtsi for ZBT WE1326 and WE3526
The hardware of these two models looks the same. This patch also
disabled unused i2c bus for WE3526.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16009
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-29 01:09:24 +02:00
Shiji Yang
0c2a522960 ramips: fix WiFi LED for ZBT WE3526
All WiFi LEDs should be triggered by low level voltage.

Fixes: https://github.com/openwrt/openwrt/issues/7485
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16009
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-29 01:09:24 +02:00
Shiji Yang
ddb322a7c8 ramips: fix PCIe port number for ZBT WE3526
From the kernel log, we are using PCIe port 1 and 2.

dmesg:
```
[ 0.963526] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[ 0.970432] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 0.975312] mt7621-pci 1e140000.pcie: PCIE2 enabled
[ 1.071442] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[ 1.130382] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
```

Fixes: https://github.com/openwrt/openwrt/issues/16000
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16009
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-29 01:09:24 +02:00
Rani Hod
5d0ccaf67c ramips: mt7621: add support for Wodesys WD-R1802U
This commit adds support for a dual-band AX1800 wall plug manufactured
by Shenzhen Century Xinyang Tech Co., Ltd.

CPU:	Mediatek MT7621A (2 cores, 4 threads)
RAM:	256i MiB DDR3 (Samsung K4B2G1646F-BCNB)
ROM:	16 MiB SPI NOR (Winbond W25Q128JVPQ)
Wired:	one gigabit RJ45 port (with green/yellow non-GPIO LEDs)
WiFi:	Mediatek MT7905DAN + MT7975DN (DBDC 2x 2T2R)
Ant.:	four 2 dBi external antennas (two 2.4GHz, two 5 GHz)
GPIO:	tri-color status LED (GPIO 13, 14, 16);
	reset button (GPIO 18)
Power:	12V 2-pin JST-XH on main PCB
	110/220V AC to 12V1A DC on auxiliary PCB
UART:	115200 8n1, SMD pads available on the PCB as J4
	pinout is [3v3] (Rx) (Tx) (Gnd)
MAC:	1C:BF:CE:xx:xx:xx	(2.4 GHz, label)
	1C:BF:CE:xx:xx:xx + 1	(ethernet [1])
	1C:BF:CE:xx:xx:xx + 2	(5 GHz)

Original firmware is LEDE Reboot 17.01-SNAPSHOT (kernel 4.4.198)
with a few custom packages and a non-LuCI web interface.
Telnet and SSH are enabled, requiring an unknown root password [2].
Root password is also needed to access the router via UART console,
but passwordless telnet can be enabled via a trivial web exploit [3]
and then the root password can be removed by editing `/etc/shadow`.

Installation: First upload `sysupgrade` binary via web interface at
  `http://192.168.188.1/settings.shtml` and wait until getting back to
  the home screen (select network to extend). The installation fails
  since the original firmware uses `swconfig` and recent versions of
  OpenWrt use DSA. However, the sysupgrade file is uploaded correctly
  and stored at `/tmp/upgrade.bin`, so it can be written to flash via
  the web exploit [4] (both `mtd -r write` and `sysupgrade -Fn` work
  fine). Passwordless telnet/ssh is not needed for installation.
  Alternatively, use u-boot menu to load image via TFTP.

Notes:
- Device model in LEDE is "MediaTek MT7621 RFB (802.11ax,SNOR)".
- It is sold under several names, among them are Wodesys WD-R1802U,
  Fenvi F-AX1802U, and EDUP EP-2971; the Wodesys brand was selected
  since it is referenced in `/etc/banner` and `/etc/hosts`, and the
  PCB is marked "WD518A V1.0".
- Instead of a standard ethernet transformer, the PCB has a few tiny
  SMD coils.

[1] Original firmware sets ethernet MAC to 1C:BF:CE:E7:62:1D based on
    offset `0x3fff4` in the Factory partition; since this is the same
    MAC for all units, whereas WiFi MACs stored at offsets 0x6 and 0xc
    are unique, it was decided to use <label MAC + 1> for ethernet.
[2] root:$1$7rmMiPJj$91iv9LWhfkZE/t7aCBdo.0:18388:0:99999:7:::
[3] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \
    -d page=Lang -d langType="en;killall telnetd;telnetd -l /bin/sh"
[4] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \
    -d page=Lang -d langType="en;mtd -r write /tmp/upgrade.bin firmware"

Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15777
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-28 20:21:08 +02:00
Hauke Mehrtens
dbccc9cf91 ramips: eth: Fix PHY access over mtk_eth_soc driver
.ndo_do_ioctl is not called any more. For PHY MII ioctl handling, the
kernel calls .ndo_eth_ioctl now.

See upstream Linux kernel commit:
https://git.kernel.org/linus/a76053707dbf0dc020a73b4d90cd952409ef3691

Link: https://github.com/openwrt/openwrt/pull/16005
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-28 16:12:51 +02:00
Rafał Miłecki
74879140a1 treewide: fixup models names for UniFi U6 series
Ubiquiti has a set of UniFi 802.11ax (Wi-Fi 6) AP devices. All models
include "U6" in their names and also have code names with no special
characters (including spaces).

Examples:
1. U6 Lite (codename U6-Lite)
2. U6 Long-Range (codename U6-LR)
3. U6+ (codename U6-PLUS)
4. U6 Pro (codename U6-Pro)
5. U6 Mesh (codename U6-Mesh)
6. U6 Mesh Pro (codename U6-Mesh-Pro)
7. U6 Enterprise (codename U6-Enterprise)

Use proper full names for those devices. Names in OpenWrt/DTS code may
need updating too but it can be handled later.

Cc: Elbert Mai <code@elbertmai.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Henrik Riomar <henrik.riomar@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-07-25 11:18:25 +02:00
Maxim Anisimov
6c45f3527f ramips: add support for Keenetic KN-3510
Keenetic KN-3510 is a 2.4/5 Ghz band 11ax access point

Specification:
- System-On-Chip: MT7621AT
- CPU/Speed: 880 MHz
- Flash-Chip: Macronix MX30LF1G28AD-TI
- Flash size: 128 MiB
- RAM: 256 MiB
- 2x 10/100/1000 Mbps Ethernet
- PoE, 802.3af/at
- 4x internal antennas
- UART (J1) header on PCB (115200 8n1)
- WiFi: MT7915 2x2 2.4G 573.5Mbps + 2x2 5G 1201Mbps
- 2x LED, 2x button, 1x mode switch

Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3510-squashfs-factory.bin"
   to "KN-3510_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-21 20:54:31 +02:00
Borys Zhukov
f25cd55bd1 ramips: add support for Netgear WAX214v2
Netgear WAX214v2 is an 802.11ax (Wi-Fi 6) wireless access point.

Specifications:
* SoC: MediaTek MT7621AT
* RAM: 512 MiB
* Flash: NAND 128 MiB (ESMT PSU1GA30DT)
* Wi-Fi: 2.4/5 GHz 4T4R (MediaTek MT7915E)
* Ethernet: 1x 10/100/1000 Mbps LAN
* Switch: MediaTek MT7530 (SoC built-in)
* LEDs/Keys
  * Power (green, blue, amber)
  * LAN (green, amber)
  * WLAN 2.4GHz (green, blue)
  * WLAN 5GHz (green, blue)
  * Reset button
* USB: None
* UART: Marked J1 on board, 115200 8N1
* Power
  * 12 VDC, 1.5 A
  * IEEE 802.3at (PoE+)

Load addresses (same as Netgear WAX202):
* stock
  * 0x80010000: FIT image
  * 0x81001000: kernel image -> entry
* OpenWrt
  * 0x80010000: FIT image
  * 0x82000000: uncompressed kernel+relocate image
  * 0x80001000: relocated kernel image -> entry

MAC addresses as verified by OEM firmware:

vendor   OpenWrt   address
eth0     lan       label
ra0      phy0      label + 2
rax0     phy1      label + 3

Installation:
* Flash the factory image by TFTP to the bootloader.
  NMRP can be used to TFTP without opening the case.

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

References to WAX214v2 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX214v2-V1.0.1.5-gpl-src.tar.gz

* openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax214v2.dts
  DTS file for this device.

Signed-off-by: Borys Zhukov <borys@zhukov.org>
Link: https://github.com/openwrt/openwrt/pull/14401
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-21 20:05:14 +02:00
Eros Brigmann
ba30cbef41 ramips: add support for Wavlink WL-WN531G3-A2
This device is exactly the same as WL-WN531G3 but with different partition layout and different MAC layout. Labeled as Quantum D4G Rev.: A2.

Hardware
--------
SoC:   Mediatek MT7620A
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
  - 2x 10/100/1000 Mbps Ethernet (RTL8211F)
  - 3x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 external antennas
BTN:
  - 1x Reset button
  - 1x Touchlink button
  - 1x Turbo button
  - 1x Wps button
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 5x Blue leds (ethernet ports)
  - 1x Power led
  - 1x Wifi led
UART:
  - 57600-8-N-1
Everything works correctly.

Installation
------------
Flash the initramfs image in the OEM firmware interface
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Notes
-----
1) Router mac addresses:
   LAN XX:XX:XX:XX:XX:0F (factory @ 0x28)
   WAN XX:XX:XX:XX:XX:10 (factory @ 0x2e)
   WIFI 2G XX:XX:XX:XX:XX:11 (factory @ 0x04)
   WIFI 5G XX:XX:XX:XX:XX:12 (factory @ 0x8004)

   LABEL XX:XX:XX:XX:XX:11

Signed-off-by: Eros Brigmann <erosbrigmann@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15876
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-21 18:47:37 +02:00
Luca Piccirillo
7390642237 treewide: match the COMFAST brand name across supported devices
COMFAST CF-E393AX
COMFAST CF-E390AX & CF-EW72 V2
COMFAST CF-WR617AC

Signed-off-by: Luca Piccirillo <luca.piccirillo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14690
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-21 18:08:49 +02:00
Mieczyslaw Nalewaj
93ead910dc ramips: mt7620: remove kmod-switch-rtl8366-smi from package list
Remove kmod-switch-rtl8366-smi from the package list, as it is still loaded
because kmod-switch-rtl8367b depends on it

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15757
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-21 14:57:03 +02:00
Shiji Yang
708b77f549 ramips: fix image recipe for ASUS RT-N56U
The OpenWrt image metadata includes checksum validation. Therefore,
it must be generated at the end.

Fixes: https://github.com/openwrt/openwrt/issues/9045
Fixes: https://github.com/openwrt/openwrt/issues/13674
Link: https://patchwork.ozlabs.org/project/openwrt/patch/TYCP286MB08952FAACDFA234C5E052131BCD82@TYCP286MB0895.JPNP286.PROD.OUTLOOK.COM/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-07-13 14:30:42 +02:00
Daniel Golle
04818d5857 ramips: mt7621: reduce MMC clock to 48 MHz
The switch to the upstream mmc-mtk driver caused problems with MT7621
because of unstable too high clock frequency:
[   49.643291] mmc0: error -88 whilst initialising SD card
[   49.890047] mmc0: error -88 whilst initialising SD card
[   50.142414] mmc0: error -88 whilst initialising SD card
[   50.419218] mmc0: error -88 whilst initialising SD card
...

Fix this by reducing the clock speed to 48 MHz instead of 50 MHz, which
is also the value used in upstream Linux mt7621.dtsi.

With that change applied SD cards work as expected on MT7621 devices
also with the new driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-07-12 02:43:58 +01:00
Shiji Yang
238aa35c49 ramips: improve support for HiWiFi HC5861 SDHC
1. Override max clock frequency to a stable value 24 MHz.
2. Use voltage regulator to control the power supply.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-07-11 18:57:42 +02:00
Shiji Yang
b9cec661f6 ramips: switch default SDHC driver to kmod-mmc-mtk
Now that the SDHC of MT762{0,1,8} has been supported upstream, it's
time to switch the default driver to the upstream one. We will still
keep the old driver for users to choose from.

Tested on HiWiFi HC5861 (MT7620A) and HiWiFi HC5661A (MT7628N).

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-07-11 18:57:41 +02:00
Shiji Yang
338f40b3b4 ramips: make SoC dtsi compatible with upstream mmc-mtk driver
Add all essential MTK SDHC properties to support the new mmc-mtk
driver. Since this driver relies on power regulators, we also
need to enable this feature for MT7620, just like MT762{1,8}.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: John Thomson <git@johnthomson.fastmail.com.au>
2024-07-11 18:57:41 +02:00
Shiji Yang
53f23d1613 ramips: modules: add Mediatek MMC driver package
This is the upstream implementation of the MTK SD/SDIO/MMC card
reader driver. It is an alternative solution for the downstream
driver package "kmod-sdhci-mt7620".

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: John Thomson <git@johnthomson.fastmail.com.au>
2024-07-11 18:57:41 +02:00
Shiji Yang
e755831f06 ramips: mtk-sd: initialize pad delay and drive strength
Port vendor register init values to upstream MTK SHDC driver.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-07-11 18:57:41 +02:00
Shiji Yang
a22bdf7c09 ramips: mtk-mmc: use "cd-inverted" to set CD line polarity
"cd-inverted" is an upstream documented property used to indicate
the CD line is actived high. We will introduce a new upstream SDHC
driver, and this change will make them compatible with each other.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-07-11 18:57:41 +02:00
Shiji Yang
73eeac49be ramips: limit max spi clock frequency to 50 MHz
In the past few years, we have received several reports about SPI
Flash not working properly. This is caused by excessively fast
clock frequency. It's really annoying to fix them one by one. Let's
reduce these aggressive frequencies to 50 MHz. This is a safe and
suggested value in the vendor SDK.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-07-10 12:20:35 +02:00
Shiji Yang
5f250cfd04 ramips: gpio: convert to the generic GPIO driver
Drop most of the code in favor of the generic MMIO GPIO driver.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-07-04 22:20:47 +02:00
Shiji Yang
7be6323d3f ramips: gpio: use devm_platform_ioremap_resource()
Simplify the code.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-07-04 22:20:47 +02:00
Shiji Yang
256f1648e7 ramips: gpio: remove header "gpio.h"
There are no source files using it.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-07-04 22:20:47 +02:00
Shiji Yang
24459dc108 ramips: gpio: always use dynamic GPIO numberspace base
The new numberspace base starts from 512 instead of 0. The number
base seems come from the kernel symbol CONFIG_GPIOLIB_FASTPATH_LIMIT.

Suppress warning:

gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-07-04 22:20:47 +02:00
Shiji Yang
2f1ff5b4ce ramips: mt7621: fix GPIO switch pin number
The numberspace base has been changed since 6.6 kernel:

chip_num   chip0   chip1   chip2 (32 gpios per bank)
old base    480     448     416
new base    512     544     576

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-07-04 22:20:47 +02:00
Shiji Yang
a7f37b401b ramips: remove useless compatible strings from SoC dtsi
These removed compatible strings do not exist in the source code
nor the dt-binding documents. They are useless.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-07-02 10:13:45 +02:00
Daniel Golle
646ebbd32c ramips: yuncore_g720: fix buttons
Turns out the device got two buttons, while the currently listed on is
actually WPS, and the other (will hidden) button is intended as RESET.
Update DT accordingly.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-06-25 20:42:54 +01:00
Robert Marko
215a3ca2a4 treewide: refresh patches
These need to be refreshed, probably the generic backports affected them.

Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-24 09:46:19 +02:00
Robert Marko
73a9f9f857 generic: platform/mikrotik: add NVMEM layout driver
Currently, information from MikroTik hard_config is only available via
sysfs, meaning that we have to rely on userspace to for example setup MACs.

So, lets provide a basic NVMEM layout based driver to expose the same cells
as sysfs driver exposes.

Do note that the we dont extract the WLAN caldata and BDF-s at this point.

Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/15665
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-20 15:53:55 +02:00
Hauke Mehrtens
8e214d48b1 ramips: Fix DOS line endings
Convert line endings from DOS to Unix using dos2unix.

Fixes: 2da2705a44 ("ramips: add support for WINSTARS WS-WN536P3")
Fixes: 5560791bbd ("ramips: add support for OpenFi 5Pro Travel Router")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-06-19 00:01:41 +02:00
Rosen Penev
6ff598306f
treewide: gpio to gpios
gpio is deprecated. Found with dtc's -Wdeprecated_gpio_property

Used git grep -E $'\tgpio = <' to make the changes.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15681
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-06-17 12:57:06 +02:00
Sven Huang
5560791bbd ramips: add support for OpenFi 5Pro Travel Router
OpenFi 5Pro is a DualBand Travel Router, based on MT7621A.

Specification:
- Type             : Travel Wi-Fi Router(built-in Type-C Power Cable)
- Size             : 63 x 93 x 24mm
- Power            : Internal Type-C Cable PD/DC 5V@2A
- SoC              : MediaTek MT7621A
- RAM              : DDR3 512 MB
- Flash            : SPI-NOR 64MB (W25Q512)
- WLAN             : 2.4/5GHz 2T2R (MediaTek MT7603e/MT7613)
- Ethernet         : 2x 10/100/1000Mbps
- USB              : 1 x USB 2.0
- SDHCI            : 1 x TF Slot (Max 512GB)
- LEDs             : 3 x LEDs  (GPIO#16 gpio#17 gpio#14)
- Button           : 1 x Reset (GPIO#18),  1 x WPS (GPIO#13)
- UART             : 1 x UART for Debug, 115200 8N1 (Pinout: GND TX RX 3.3V)
- UART 2           : 1xUART2  (Pinout: GND TX2 RX2 3.3V )

How to upgrade image in uboot

1. press reset button when boot for 5sec.
2. access 192.168.21.1 in web ui.
3. select image and upload

Signed-off-by: Sven Huang <1036456939@qq.com>
2024-06-17 00:01:51 +02:00
Sven Huang
2da2705a44 ramips: add support for WINSTARS WS-WN536P3
WS-WN536P3 is a 2.4/5 GHz band 11ac router, based on MT7621DA.

Specification:

- SoC               : MediaTek MT7621DA
- RAM               : DDR3 128 MB
- Flash             : SPI-NOR 16MB
- WLAN              : 2.4/5 GHz 2T2R (MediaTek MT7603e/MT7613)
- Ethernet          : 5x 10/100/1000 Mbps
- LEDs              : 1x Sys 1x WIFI 5x Ethernet LEDs(connect to switch)
- Keys              : 1x Reset 1x WPS 1x Turbo
- USB               : x1
- UART              : 1xUART
- settings        : 115200n8

How to upgrade image in uboot

1. press reset button when boot for 5sec.
2. access 192.168.10.1 in web ui.
3. select image and upload

Signed-off-by: Sven Huang <1036456939@qq.com>
2024-06-16 23:42:59 +02:00
Mieczyslaw Nalewaj
b0d418035e ramips: tplink_8m: cleaning up nvmem-cells definitions
Move nvmem-cells definitions to dts files for compatibility with other files
in which mt7628an_tplink_8m.dtsi is loaded, to prevent overwriting

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-06-16 21:24:11 +02:00
Mieczyslaw Nalewaj
3ce71a1ead ramips: netgear_r6xxx: cleaning up nvmem-cells definitions
Move nvmem-cells definitions to dts files to prevent overwriting

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-06-16 21:24:11 +02:00
Mieczyslaw Nalewaj
fd610a2083 ramips: elecom_wrc-gs-1pci: cleaning up nvmem-cells definitions
Move nvmem-cells definitions to dts files to prevent overwriting

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-06-16 21:24:11 +02:00
Mieczyslaw Nalewaj
c54ce12a74 ramips: cudy_x6: cleaning up nvmem-cells definitions
Move nvmem-cells definitions to dts files to prevent overwriting

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-06-16 21:24:11 +02:00
Mieczyslaw Nalewaj
e750c22904 ramips: xiaomi,mi-ra75: cleaning up nvmem-cells definitions
Remove nvmem-cells definitions due to duplication
in mt7628an_xiaomi_mi-router-4.dtsi

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-06-16 21:24:11 +02:00
Mieczyslaw Nalewaj
3504667bbe ramips: tplink,archer-c2-v1: cleaning up nvmem-cells definitions
Remove nvmem-cells definitions due to duplication
in mt7620a_tplink_8m.dtsi

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-06-16 21:24:11 +02:00
Mieczyslaw Nalewaj
e125cf5a8c ramips: hiwifi,hc5861: cleaning up nvmem-cells definitions
Remove nvmem-cells definitions due to duplication
in mt7620a_hiwifi_hc5x61.dtsi

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-06-16 21:24:11 +02:00
Shiji Yang
05aec66d53 ramips: fix MAC address for some devices
1. Remove unused macaddr NVMEM cells.
2. Fix "mac-base" compatible cells references.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-06-15 22:54:52 +02:00
John Audia
f34620f146 kernel: bump 6.6 to 6.6.33 and adjust subarches
This commit accomplishes three goals:
1. bump 6.6 to 6.6.33
2. kernel: modules: video: change package definition for fb for
   upstream changes[1]
3. kernel/multiple subtargets: add CONFIG_FB_IOMEM_FOPS=y to all
   subtargets which also set CONFIG_FB_CORE=y.

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.33

Removed upstreamed:
	pending-6.6/195-block-fix-and-simplify-blkdevparts-cmdline-parsing.patch[2]
	gemini/patches-6.6/0003-net-ethernet-cortina-Locking-fixes.patch[3]

Manually rebased:
	ramips/patches-6.6/810-uvc-add-iPassion-iP2970-support.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-6.6.y&id=c00e8fd749502c02085534c60b1edca4fc479c91
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.33&id=99bbbd9aea059f8a206736dc601be2ae61d366fb
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.33&id=8f6f82d6a205ceb3aba8d279f9ff6eeea0b1689b

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: John Audia <therealgraysky@proton.me>
2024-06-15 22:44:06 +02:00
Mikhail Zhilkin
ef845675f5 ramips: fix wrong dts file permission
This file is executable:
   target/linux/ramips/dts/mt7621_dlink_dir-2150-a1.dts
Has to be fixed.

Fixes: 30e8fd73ec ("ramips: Add support for D-Link DIR-2150-A1")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2024-06-14 14:44:04 +02:00
Mikhail Zhilkin
61dce63c04 ramips: fix random LAN MAC for sercomm dxx devices
This commit fixes random lan mac for sercomm dxx devices.

Fixes: 3395184825 ("ramips: mt7621: nix mac-address-increment")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2024-06-14 14:43:07 +02:00
Mikhail Zhilkin
24d2519755 ramips: fix wrong eeprom data for sercomm dxx devices
This commit fixes wrong WiFi eeprom data:
   /sys/kernel/debug/ieee80211/phy0/mt76/eeprom
   /sys/kernel/debug/ieee80211/phy1/mt76/eeprom

Fixes: fb4cea45ec ("ramips: convert MT7603 EEPROM to NVMEM format")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2024-06-14 14:41:30 +02:00
Sebastian Schaper
aa4d63c2da ramips: add support for 7Links WLR-1240
The WLR-1240 (ZX-5434) is an AC1200 Wave 2 outdoor repeater
with omnidirectional antennas for wall or pole mounting.
The device is manufactured by Todaair and meant to be used with
a tuya-based app, there is no webinterface for configuration.

Specifications:
- MT7628AN, 8 MiB SPI NOR flash, 64 MiB RAM, 2x2 802.11n
- MT7613 2x2 802.11ac Wave 2
- 802.3af PoE or 12V 1A 5.5x2.1 power supply (included)
- top RGB LED ring

TFTP installation:
- rename sysupgrade to `firmware_auto.bin`
- provide at 192.168.1.10 during boot

HTTP installation:
- keep reset button pressed for 5 seconds during power on (light blue
  LED flashes slowly, then quickly to confirm, then remains steady on)
- recovery web interface is at 192.168.1.1, upload sysupgrade

Opening the device
- use suction cup to remove top cap within LED ring
- two screws are located in holes underneath silicone sealant
- two further screws are located at the bottom

initramfs boot
- open device, connect serial console (pins are labelled)
- keep pressing `4` during second tftp attempt to enter uboot shell
- run `tftpboot 82000000` to avoid memory overlap, then `bootm`

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2024-06-11 00:09:06 +02:00
Sebastian Schaper
3d6cbe287a ramips: add support for 7Links WLR-1230
The WLR-1230 (ZX-5207) is an AC1200 Wave 2 outdoor repeater
with sector antennas for wall or pole mounting.
The device is manufactured by Todaair and meant to be used with
a tuya-based app, there is no webinterface for configuration.

Specifications:
- MT7628AN, 8 MiB SPI NOR flash, 64 MiB RAM, 2x2 802.11n
- MT7613 2x2 802.11ac Wave 2
- 802.3af PoE or 12V 1A 5.5x2.1 power supply (included)
- 3 LEDs WLAN, LAN, RES; PWR LED is not software-controllable

TFTP installation:
- rename sysupgrade to `firmware_auto.bin`
- provide at 192.168.1.10 during boot

HTTP installation:
- keep reset button pressed for 5 seconds during power on (LEDs
  flash slowly, then quickly to confirm, then remain steady on)
- recovery web interface is at 192.168.1.1, upload sysupgrade

Opening the device
- two screws are located in the bottom left and right corners
  underneath the label, inner tray slides out easily

initramfs boot
- open device, connect serial console (pins are labelled)
- keep pressing `4` during second tftp attempt to enter uboot shell
- run `tftpboot 82000000` to avoid memory overlap, then `bootm`

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2024-06-11 00:09:06 +02:00
Luis Mita
d780d530dd ramips: mt76x8: sync Cudy TR1200 v1 naming
Cudy assigns hardware versions to its devices on its website, and
the Cudy TR1200 router is now Cudy TR1200 v1.
OpenWrt currently uses both variants, and this commit removes
inconsistencies using only the new name.

Signed-off-by: Luis Mita <luis@luismita.com>
2024-06-10 10:13:56 +02:00
Mieczyslaw Nalewaj
df28fe4b59 kernel: rtl8367b: remove unnecessary cpu_port setting
Set the appropriate cpu_port value based on the use of realtek,extif0 to extif2
instead of the additional cpu_port parameter.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15033
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-08 16:28:37 +02:00
INAGAKI Hiroshi
1fbfc251c9 ramips: add support for Buffalo WSR-2533DHPL2
Buffalo WSR-2533DHPL2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MediaTek MT7621A.

Specification:

- SoC           : MediaTek MT7621AT
- RAM           : DDR3 128 MiB (Winbond W631GG6MB12J)
- Flash         : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN          : 2.4/5 GHz (2x MediaTek MT7615N)
- Ethernet      : 10/100/1000 Mbps x4
  - Switch      : MediaTek MT7530 (SoC)
- LED/keys      : 8x/6x (2x buttons, 1x slide-switch)
- UART          : through-hole on PCB (J4)
  - arrangement : 3.3V, GND, TX, RX from triangle-mark
  - settings    : 57600n8
- Power         : 12VDC 1.5A

Flash instruction using factory.bin image:

1. boot WSR-2533DHPL2 normally with "Router" mode
2. access to the WebI ("http://192.168.11.1/") on the device and open
   firmware update page
   ("管理" -> "ファームウェア更新")
3. select the OpenWrt factory.bin image and click update ("更新実行")
   button
   Attention: do not use "factory-uboot.bin" image
4. Wait ~120 seconds to complete flashing

Flash instruction using initramfs image:

1. prepare the TFTP server with the initramfs image renamed to
   "linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL2
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL2 downloads
   the initramfs image and boot with it automatically
4. on the initramfs image, download the factory-uboot.bin image to the
   device and perform sysupgrade with it and "-F" option
5. wait ~120 seconds to complete flashing

Notes:

- There are 2x factory*.bin images for different purposes.

  - factory.bin      : for flashing on OEM WebUI
  - factory-uboot.bin: for flashing on OEM bootloader or initramfs image

  factory-uboot.bin is useful for recoverying the device, or refreshing
  when the kernel partition is expanded in the future. sysupgrade on
  this device accepts factory-uboot.bin with option "-F", but on that
  situation, user configurations won't be kept, so it's not for normal
  use.

MAC addresses:

LAN    : 18:EC:E7:xx:xx:E0 (board_data, "mac" (text))
WAN    : 18:EC:E7:xx:xx:E0 (board_data, "mac" (text))
2.4 GHz: 18:EC:E7:xx:xx:E1 (Factory, 0x4    (hex))
5 GHz  : 18:EC:E7:xx:xx:E4 (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-06-05 21:14:16 +02:00
INAGAKI Hiroshi
ea8d140b25 ramips: add support for Buffalo WSR-2533DHPLS
Buffalo WSR-2533DHPLS is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.

Very similar to Buffalo WSR-2533DHPL, but with NAND, different GPIO
and TRX partitions.

Specification:

- SoC           : MediaTek MT7621AT
- RAM           : DDR3 256 MiB (Samsung K4B2G1646F-BYMA)
- Flash         : RAW-NAND 128 MiB
                  (Winbond W29N01HV or KIOXIA TC58BVG0S3HTAI0)
- WLAN          : 2.4/5 GHz (2x MediaTek MT7615N)
- Ethernet      : 10/100/1000 Mbps
  - Switch      : MediaTek MT7530 (SoC) 4 ports
- LED/keys      : 8x/6x (2x buttons, 1x slide-switch)
- UART          : through-hole on PCB (J4)
  - arrangement : 3.3V, GND, TX, RX from triangle-mark
  - settings    : 115200n8
- Power         : 12VDC 1.5A

Flash instruction using factory.bin image:

1. boot WSR-2533DHPLS normally with "Router" mode
2. access to the WebI ("http://192.168.11.1/") on the device and open
   firmware update page
   ("管理" -> "ファームウェア更新")
3. select the OpenWrt factory.bin image and click update ("更新実行")
   button
   Attention: do not use "factory-uboot.bin" image
4. Wait ~120 seconds to complete flashing

Flash instruction using initramfs image:

1. prepare the TFTP server with the initramfs image renamed to
   "linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPLS
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPLS downloads
   the initramfs image and boot with it automatically
4. on the initramfs image, download the factory-uboot.bin image to the
   device and perform sysupgrade with it and "-F" option
5. wait ~120 seconds to complete flashing

Notes:

- The embedded addresses in eeprom data in Factory partition have
  Buffalo's OUI, but they don't match with the actual addresses
  assigned to wlan devices. So fixup addresses by the user-space
  script.

  root@localhost:/# hexdump -C /dev/mtdblock3 | grep "^0000[08]000\s"
  00000000  15 76 a0 00 88 57 ee bc  01 a8 15 76 c3 14 00 80  |.v...W.....v....|
  00008000  15 76 a0 00 88 57 ee bc  01 f8 15 76 c3 14 00 80  |.v...W.....v....|

  See "MAC addresses" below for actual addresses.

- There are 2x factory*.bin images for different purposes.

  - factory.bin      : for flashing on OEM WebUI
  - factory-uboot.bin: for flashing on OEM bootloader or initramfs image

  factory-uboot.bin is useful for recoverying the device, or refreshing
  when the kernel partition is expanded in the future. sysupgrade on
  this device accepts factory-uboot.bin with option "-F", but on that
  situation, user configurations won't be kept, so it's not for normal
  use.

MAC addresses:

LAN    : 90:96:F3:xx:xx:30 (board_data, "mac" (text))
WAN    : 90:96:F3:xx:xx:30 (board_data, "mac" (text))
2.4 GHz: 90:96:F3:xx:xx:31
5 GHz  : 90:96:F3:xx:xx:38

[original work]
Signed-off-by: Audun-Marius Gangstø <audun@gangsto.org>
[convert to ubi, fix/improve DT, add sysupgrade support]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-06-05 21:14:16 +02:00
INAGAKI Hiroshi
d529ac5da8 ramips: mt7621: switch trx parser to parser_trx from mtdsplit
Switch trx parser to parser_trx of Linux Kernel from mtdsplit_trx to
split firmware partition using model-specific trx magic number on
some Buffalo devices.
This change is tested on Buffalo WSR-2533DHPL.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-06-05 21:14:16 +02:00
Michał Kępień
a60721f2ed mikrotik: switch to Yafut for building MikroTik NOR images
The Yafut tool now has limited capabilities for working on filesystem
images stored in regular files.  This enables preparing Yaffs2 images
for devices with NOR flash using upstream Yaffs2 filesystem code instead
of the custom kernel2minor tool.

Since minimizing the size of the resulting filesystem image size is
important and upstream Yaffs2 code requires two allocator reserve blocks
to be available when writing a file to the filesystem, a trick is
employed while preparing an OpenWRT image: the blank filesystem image
that Yafut operates on initially contains two extra erase blocks that
are chopped off after the kernel file is written.  This is safe to do
because Yaffs2 has a true log structure and therefore only ever writes
sequentially (and the size of the kernel file is known beforehand).
While the two extra erase blocks are necessary for writes, Yaffs2 code
seems to be perfectly capable of reading back files from a "truncated"
filesystem that does not contain these extra erase blocks.

In terms of image size, this new approach is only marginally worse than
the current kernel2minor-based one: specifically, upstream Yaffs2 code
needs to write three object headers (each of which takes up an entire
data chunk) when the kernel file is written to the filesystem:

  - an object header for the kernel file when it is created,

  - an object header for the root directory when the kernel file is
    created,

  - an updated object header for the kernel file when the latter is
    fully written (so that its new size can be recorded).

kernel2minor only writes two of these headers, which is the absolute
minimum required for reading the file back.  This means that the
Yafut-based approach causes firmware images to be at most one erase
block (64 kB) larger than those created using kernel2minor, but only in
the very unfortunate scenario where the size of the kernel file is
really close to a multiple of the erase block size.

The rest of the calculations performed when the empty filesystem image
is first prepared stems from the Yaffs2 layout used by MikroTik NOR
devices: each 65,536-byte erase block contains 63 chunks, each of which
consists of 1024 bytes of data followed by 16-byte Yaffs tags without
ECC data; each such group of 63 chunks is then followed by 16 bytes of
padding, which translates to "-C 1040 -B 64k -E" in the Yafut
invocation.  Yaffs2 checkpoints and summaries are disabled (using
Yafut's -P and -S switches, respectively) as they are merely performance
optimizations that require extra storage space.  The -L and -M switches
are used to force little-endian or big-endian byte order (respectively)
in the resulting filesystem image, no matter what byte order the build
host uses.  The tr invocation is used to ensure that the filesystem
image is initialized with 0xFF bytes (which are an indicator of unused
space for Yaffs2 code).

Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Link: https://github.com/openwrt/openwrt/pull/13453
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-05 17:03:24 +02:00
Luis Mita
f1091ef7ac ramips: mt76x8: add support for Cudy TR1200 v1
Hardware:
 - SoC: MediaTek MT7628AN (MIPS 580MHz)
 - Flash: 16 MiB XMC 25QH128CH10
 - RAM: 128 MiB ESMT M14D1G1664A
 - WLAN: 2.4 GHz (MT7628), 5 GHz (MT7613BEN 802.11ac)
 - Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
 - USB 2.0 port
 - Buttons: 1 Reset button, 1 slider button
 - LEDs: 1x Red, 1x White
 - Serial console: unpopulated header, 115200 8n1
 - Power: 5 VDC, 2 A

MAC addresses:
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | 80:af:ca:xx:xx:x0 | label     |
| LAN     | 80:af:ca:xx:xx:x0 | label     |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label     |
| WLAN 5g | 80:af:ca:xx:xx:x2 | label+2   |
+---------+-------------------+-----------+

Installation:
The installation must be done via TFTP by disassembling the router.
On other occasions Cudy has distributed intermediate firmware to make
installation easier, and so I recommend checking the Wiki for this
device if there is a more convenient solution than the one below.

To install using TFTP:
1. Upgrade to a beta firmware (signed by Cudy) that can be downloaded
from the wiki. This is required in order to use an unlocked u-boot.
2. Connect to UART.
3. While the router is turning on, press 1.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP
server and an OpenWrt initramfs-kernel.bin firmware file as recovery.bin.
5. Press Enter three times. Verify the filename.
6. If you can reach LuCI or SSH now, just use the sysupgrade image with
the 'Keep settings' option turned off.

If you don't want to use the beta firmware nor the unlocked u-boot, you
can install the firmware writing the sysupgrade image on the firmware
partition of the SPI flash.

Signed-off-by: Luis Mita <luis@luismita.com>
2024-06-05 10:44:44 +02:00
Shiji Yang
6e51b363e9 ramips: simplify multi-phy support patches
For MT7620, we should always prevent main ethernet interface from
going down due to phy link changes. And the ralink net driver does
not support cable test function, so this patch won't change any
behavior.

Ref:
6fcba5eec3 ("ramips: port 0034-NET-multi-phy-support.patch to 5.4")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/15591
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2024-06-04 16:19:41 +08:00
Keith Harrison
6707eba9f0 ramips: add support for D-Link DIR-2055 A1
Add support for D-Link DIR-2055 A1 based on similarities to DIR-1960 A1,
as well as various DIR-8xx A1 models. Existing DIR-1960 A1 openwrt
"factory" firmware installs without modifications via the D-Link Recovery
GUI and has no known incompatibilities with the DIR-2055 A1.

Changes to be committed:
new file:   target/linux/ramips/dts/mt7621_dlink_dir-2055-a1.dts
modified:   target/linux/ramips/image/mt7621.mk
modified:   target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
modified:   target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh

Specifications:

    Board: Not known
    SoC: MediaTek MT7621 Family (MT7621AT)
    RAM: 256 MB (Micron 9OK17 D9PTK, should be DDR3 MT41K128M16JT-125)
    Flash: 128 MB (Winbond W29N01HVSINA)
    WiFi: MediaTek MT7615 Family (MT7615N x2)
    Switch: 1 WAN, 4 LAN (Gigabit)
    Ports: 1 USB 3.0 (front)
    Buttons: Reset, WiFi Toggle, WPS
    LEDs: Power (white/orange), Internet (white/orange),
          WiFi 2.4G (white), WiFi 5G (white)

Notes:

    Only known difference vs. the DIR-1960 A1 is that the DIR-2055 A1
    doesn't have a USB activity LED

Serial port:

    Tested to be identical to various DIR-8xx A1 models with a similar
    enclosure/pcb design:
        Parameters: 57600, 8N1, 3.3V TTL no flow control
        Location: J1 header (close to the Reset, WiFi and WPS buttons)
        Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND
            Did not connect VCC when using

Installation:

    D-Link Recovery GUI: power down the router, press and hold the reset
    button, then re-plug it. Keep the reset button pressed until the power
    LED starts flashing orange, manually assign a static IP address under
    the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to
    http://192.168.0.1

    Some modern browsers may have problems flashing via the Recovery GUI,
    if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

Signed-off-by: Keith Harrison <keithh@protonmail.com>
2024-06-02 18:41:17 +02:00
Daniel Golle
2a25c6ace8 ramips: get rid of downstream network device label patch
Use a simple Shell script like on filogic target to get rid of downstream
patch for the Ethernet driver which was rejected upstream long ago.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-31 13:26:54 +01:00
Shiji Yang
db49d995bb ramips: modules: remove symbol CONFIG_DW_DMAC_PCI
The DW_DMAC_PCI symbol won't be automatically selected at all.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-29 10:41:49 +02:00
Shiji Yang
2240320d7f ramips: gdma: remove slave_id field
Fix compile error:
drivers/dma/ralink-gdma.c: In function 'gdma_dma_config':
drivers/dma/ralink-gdma.c:197:40: error: 'struct dma_slave_config' has no member named 'slave_id'
  197 |                 chan->slave_id = config->slave_id;
      |                                        ^~
drivers/dma/ralink-gdma.c:206:40: error: 'struct dma_slave_config' has no member named 'slave_id'
  206 |                 chan->slave_id = config->slave_id;
      |                                        ^~
make[8]: *** [scripts/Makefile.build:243: drivers/dma/ralink-gdma.o] Error 1

ref: https://lore.kernel.org/all/20211122222203.4103644-1-arnd@kernel.org/

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-29 10:41:49 +02:00
Shiji Yang
ccd50abd9f ramips: add back the gdma driver
The gdma driver has been removed from the upstream. Let's move it
to the local files. This patch also removed unsupported compatible
string and sub-target.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-29 10:41:49 +02:00
Mieczyslaw Nalewaj
1a2fc49b71 ramips: samknows whitebox v8: set wifi frequency
Set the 2.4GHz frequency for WiFi.

Fixes: #15391
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-25 20:20:30 +02:00
INAGAKI Hiroshi
50ae9337d6 ramips: add support for ELECOM WRC-X1800GS
ELECOM WRC-X1800GS is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7621A.

Specification:

- SoC               : MediaTek MT7621A
- RAM               : DDR3 256 MiB
- Flash             : RAW-NAND 128 MiB (Macronix MX30LF1G28AD-TI)
- WLAN              : 2.4/5 GHz 2T2R (MediaTek MT7915D)
- Ethernet          : 5x 10/100/1000 Mbps
  - switch          : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO)  : 7x/4x
- UART              : pin-header on PCB ("J5")
  - arrangement     : 3.3V, TX, RX, NC, GND from tri-angle marking
  - settings        : 115200n8
- Power             : 12 VDC, 1 A

Flash instruction using initramfs-factory image:

1. Boot WRC-X1800GS normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
   button
4. After flashing initramfs-factory image and reboot, upload the
   sysupgrade image and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing

Notes:

- WRC-X1800GS has 2x os images. Those are switched on every firmware
  updating on stock firmware, but dual-boot feature on this device
  cannot be handled on OpenWrt. So the 1st image is always used on
  OpenWrt.
  This is controlled by "bootnum" variable embedded in "persist"
  partition (addr: 0x4).

- WRC-X1800GS has 2x HW revisions. There are some small changes, but the
  same DeviceTree in stock firmware is used for both revisions.
  On this support of WRC-X1800GS, 2x green:wlan-2g-N LEDs are defined
  for each revision and the same default triggers are set.

MAC addresses:

LAN    : 38:97:A4:xx:xx:38 (Factory, 0x1fdfa (hex) / Ubootenv, ethaddr (text))
WAN    : 38:97:A4:xx:xx:3B (Factory, 0x1fdf4 (hex))
2.4 GHz: 38:97:A4:xx:xx:39
5 GHz  : 38:97:A4:xx:xx:3A

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-25 19:33:28 +02:00
INAGAKI Hiroshi
cd2a6906da ramips: parameterize some values in Build/znet-header
Parameterize magic number and header length to use the device-specific
values.

example:

On WRC-X1800GS, an additional ELECOM-specific header and a magic number
"COMC" are required.

Stock FW v1.18:

$ hexdump -n $((0x40080)) -C wrc-x1800gs_v1.18.bin
00000000  45 4c 45 43 4f 4d 00 00  57 52 43 2d 58 31 38 30  |ELECOM..WRC-X180|
00000010  30 47 53 00 00 00 00 00  00 00 00 00 00 00 00 00  |0GS.............|
00000020  00 00 00 00 00 00 00 00  31 2e 31 38 00 00 00 00  |........1.18....|
00000030  00 00 00 00 00 00 00 00  43 4f 4d 43 04 00 ac 00  |........COMC....|
00000040  40 f0 49 74 b1 e8 6a ca  e4 20 65 1f 34 2e 30 34  |@.It..j.. e.4.04|
00000050  28 58 56 46 2e 31 29 62  31 37 00 00 00 00 00 00  |(XVF.1)b17......|
00000060  00 00 00 00 00 00 00 00  ff ff ff ff ff ff ff ff  |................|
00000070  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
*
00040000  d0 0d fe ed 00 36 9c c0  00 00 00 38 00 36 9a e0  |.....6.....8.6..|
00040010  00 00 00 28 00 00 00 11  00 00 00 10 00 00 00 00  |...(............|
00040020  00 00 00 6c 00 36 9a a8  00 00 00 00 00 00 00 00  |...l.6..........|
00040030  00 00 00 00 00 00 00 00  00 00 00 01 00 00 00 00  |................|
00040040  00 00 00 03 00 00 00 04  00 00 00 62 65 54 97 8f  |...........beT..|
00040050  00 00 00 03 00 00 00 28  00 00 00 00 4d 49 50 53  |.......(....MIPS|
00040060  20 4f 70 65 6e 57 72 74  20 46 49 54 20 28 46 6c  | OpenWrt FIT (Fl|
00040070  61 74 74 65 6e 65 64 20  49 6d 61 67 65 20 54 72  |attened Image Tr|
00040080

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-25 19:33:28 +02:00
Lea Teuberth
2a2f53415e ramips: add support for TP-Link Archer MR200v5
Specifications:
	CPU:     MT7628AN 580MHz
	RAM:     64MB DDR2
	FLASH:   8MB EN25QH64 NOR SPI
	WIFI:    2.4GHz 2x2 MT7628 b/g/n internal
	WIFI:    5GHz 1x1 MT7610E ac/n PCI
	LTE:     Qualcomm MDM9207
	ETH:     4xLAN 100base-T integrated
	SWITCH:  RT3050-ESW Port 0,1,2,3: LAN, Port 6: CPU
	LEDS:    LAN, WAN, Power, 3x signal strength, WiFi
	BTNS:    Reset, WiFi toggle
	UART:    Near ETH ports, Vcc-GND-RX-TX, 115200, 8N1

Installation:
	1. Update using recovery mode
        - set your IP to 192.168.0.225, subnet mask: 255.255.255.0
        - start tftp server, rename tftp-recovery.bin to
          tp_recovery.bin and place it into the server's directory
        - while holdig the "reset" button, power on the device
        - keep holding "reset" until the file is being transferred

Notes:
	This board has only one MAC address programmed
        in the "romfile" partition:
        - MAC for phy0 (2.4GHz) at romfile 0xf100 (0)
        - MAC for phy1 (5GHz) at romfile 0xf100 (-1)
        - stock firmware re-uses phy0 MAC for ethernet
        - stock firmware uses romfile 0xf100 (1) for WWAN;
          not used since QMI interface is raw IP

Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
2024-05-23 22:46:26 +02:00
Hauke Mehrtens
9c84d619fc ramips: Fix use mac-base for TP-Link TL-MR6400 v4 and v5
Use mac-base for mac-base TP-Link TL-MR6400 v4 and v5

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-05-16 13:11:08 +03:00
Hauke Mehrtens
ff3d0de095 ramips: Fix wmac dts definition for TP-Link TL-MR6400 v4 and v5
This code assumed that the mt7628an_tplink_8m.dtsi file defines
mediatek,mtd-eeprom for the wmac and sets status to okay.

The mediatek,mtd-eeprom definition was removed in commit e93f41adee
("ramips: convert MT7628 EEPROM to NVMEM format") but the dts for these
two devices was not adapted to include the eeprom position on its own.

The status = "okay" property was removed in 0a1d15642f ("ramips:
mt7628: use nvmem-layout"), but the property was not added to these dts
files.

Without this change wifi does not work for these devices.

Fixes: e93f41adee ("ramips: convert MT7628 EEPROM to NVMEM format")
Fixes: 0a1d15642f ("ramips: mt7628: use nvmem-layout")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-05-16 13:11:08 +03:00
INAGAKI Hiroshi
61e8728d86 ramips: add support for ELECOM WMC-S1267GS2
ELECOM WMC-S1267GS2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) mesh extender,
based on MT7621A.

This device has almost the same hardware as WMC-M1267GST2.

Specification:

- SoC          : MediaTek MT7621A
- RAM          : DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash        : SPI-NOR 32 MiB (Winbond W25Q256JVFIQ)
- WLAN         : 2.4/5 GHz 2T2R (MediaTek MT7615D)
- Ethernet     : 10/100/1000 Mbps x4
  - switch     : MediaTek MT7530 (SoC)
- LEDs/Keys    : 6x/6x
- UART         : through-hole on PCB ("J4")
  - arrangement: 3.3V, GND, TX, RX from tri-angle marking
  - settings   : 57600n8
- Power        : 12 VDC, 1 A

Flash instruction using factory image:

1. Boot WMC-S1267GS2 normally
2. Set IP address of the computer to 192.168.2.x
3. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用") button
5. Wait ~120 seconds to complete flashing

MAC addresses:

LAN    : 04:AB:18:xx:xx:9E (Factory, 0xFFF4 (hex))
2.4 GHz: 04:AB:18:xx:xx:9F
5 GHz  : 04:AB:18:xx:xx:A0 (Factory, 0x4 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-11 19:33:28 +02:00
INAGAKI Hiroshi
927a77ecff ramips: add support for ELECOM WMC-M1267GST2
ELECOM WMC-M1267GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) mesh router,
based on MT7621A.

Specification:

- SoC          : MediaTek MT7621A
- RAM          : DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash        : SPI-NOR 32 MiB (Winbond W25Q256JVFIQ)
- WLAN         : 2.4/5 GHz 2T2R (MediaTek MT7615D)
- Ethernet     : 10/100/1000 Mbps x5
  - switch     : MediaTek MT7530 (SoC)
- LEDs/Keys    : 6x/6x
- UART         : through-hole on PCB ("J4")
  - arrangement: 3.3V, GND, TX, RX from tri-angle marking
  - settings   : 57600n8
- Power        : 12 VDC, 1 A

Flash instruction using factory image:

1. Boot WMC-M1267GST2 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing

MAC addresses:

LAN    : 04:AB:18:xx:xx:61 (Factory, 0xFFF4 (hex))
WAN    : 04:AB:18:xx:xx:62 (Factory, 0xFFFA (hex))
2.4 GHz: 04:AB:18:xx:xx:63
5 GHz  : 04:AB:18:xx:xx:64 (Factory, 0x4 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-11 19:33:28 +02:00
Sheng Huang
985af21123 ramips: add support for JDCloud RE-CP-02
- Soc: MediaTek MT7621AT
- RAM: 512 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7905DAN, MediaTek MT7975DN
- Ethernet: 1 WAN, 3 LAN (Gigabit)
- Buttons: Reset, Joylink
- LEDs: (red, blue, green), routed to one indicator in the top of the
  device
- Power: DC 12V 1A tip positive
- 1 TF Card Slot

The pins for the serial console are already labeled on the board
J4(V, R, T, G). Serial settings: 3.3V, 115200

MAC addresses:

|         | MAC               | Algorithm |
| ------- | ----------------- | --------- |
| label   | dc:d8:xx:xx:xx:01 | label     |
| LAN     | dc:d8:xx:xx:xx:01 | label     |
| WAN     | dc:d8:xx:xx:xx:02 | label+1   |
| WLAN 2g | dc:d8:xx:xx:xx:03 | label+2   |
| WLAN 5g | de:d8:xx:xx:xx:04 | label+3   |

1. rename the
   openwrt-ramips-mt7621-jdcloud_re-cp-02-squashfs-sysupgrade.bin
   to JDCOS.bin

2. start a TFTP server from IP address 192.168.68.10 and serve the
   image named JDCOS.bin

3. connect your device to the LAN port

4. power up the router and press any key on the console to interrupt
   the boot process.

5. enter the following commands on the router console

   1. setenv bootcount 6

   2. saveenv

   3. reset

      > NOTE: wait for the restart, it will automatically fetch the
      > image named JDCOS.bin from the TFTP server and write it into
      > the flash. After the writing is completed, the router will be
      > automatically restarted.

Unable to recognize large-capacity TF card, see #14042. But the patch
https://github.com/openwrt/openwrt/issues/14042#issuecomment-1910769942
works

Co-Authored-By: Jianti Chen <clbcjt@outlook.com>
Signed-off-by: Sheng Huang <shenghuang147@gmail.com>
2024-05-11 17:24:10 +02:00
Eros Brigmann
803c00e9b8 ramips: add support for Wavlink WL-WN531G3
This device is similiar to the Wavlink WL-WN531A3.
Hardware
--------
SoC:   Mediatek MT7620A
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
  - 2x 10/100/1000 Mbps Ethernet (RTL8211F)
  - 3x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 external antennas
BTN:
  - 1x Reset button
  - 1x Touchlink button
  - 1x Turbo button
  - 1x Wps button
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 5x Blue leds (ethernet ports)
  - 1x Power led
  - 1x Wifi led
UART:
  - 57600-8-N-1
Everything works correctly.

Installation
------------
Flash the initramfs image in the OEM firmware interface
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
In my case the whole device was locked and there was no way
to flash the image, except for flashing directly to the flash
via an spi-flasher. You need to put the sysupgrade image file at
the beginning of 0x60000.

Notes
-----
1) Router mac addresses:
   LAN XX:XX:XX:XX:XX:F0 (factory @ 0x28)
   WAN XX:XX:XX:XX:XX:F1 (factory @ 0x2e)
   WIFI 2G XX:XX:XX:XX:XX:F2 (factory @ 0x04)
   WIFI 5G XX:XX:XX:XX:XX:F3 (factory @ 0x8004)

   LABEL XX:XX:XX:XX:XX:F2

Signed-off-by: Eros Brigmann <erosbrigmann@gmail.com>
2024-05-10 00:05:25 +02:00
Alan Luck
30e8fd73ec ramips: Add support for D-Link DIR-2150-A1
Hardware Specification:
SoC: Mediatek MT7621DAT (MIPS1004Kc 880 MHz, dual core)
RAM: 128 MB
Storage: 128 MB NAND flash
Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
Wireless: 2.4GHz: Mediatek MT7603EN up to 300Mbps (802.11b/g/n MIMO 2x2)
Wireless: 5GHz: Mediatek MT7615N up to 1733Mbps (802.11n/ac MU-MIMO 4x4)
LEDs: Power (white & amber), Internet (white & amber)
LEDs: 2.4G (White), 5Ghz (White)
Buttons: WPS, Reset

MAC Table
Label xx:xx:xx:xx:xx:EB
LAN xx:xx:xx:xx:xx:EB
2.4Ghz xx:xx:xx:xx:xx:EC
5Ghz xx:xx:xx:xx:xx:ED
WAN xx:xx:xx:xx:xx:EE

Flash instructions:
D-Link normal OEM firmware update page
1. upload OpenWRT factory.bin like any D-Link upgrade image

D-Link Recovery GUI:
1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the recovery mode GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0
5. Call the recovery page for the device at http://192.168.0.1/
6. Use the provided emergency web GUI to upload the recovery.bin to the device

Firefox on Windows in a Private Window (incognito) works me
Internet Explorer mode in Microsoft Edge works for others
seems to not work in Linux or virtual machine on Linux for most
some see success using 'curl -v -i -F "firmware=@file.bin" 192.168.0.1'

Thanks to @frkca and @rodneyrod for testing and pushing for its creation

Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
2024-05-09 22:28:23 +02:00
Mieczyslaw Nalewaj
474b108dfe ramips: use led, function/color syntax for some tp-link archer routers
Setting the LED name and abandoning the label and using the
function/color syntax for some TP-Link Archer series routers:
Archer C2 v1, Archer C20 v1, Archer C20i and Archer C50 v1

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-09 22:24:48 +02:00
Mieczyslaw Nalewaj
d646ea8a00 ramips: use function/color syntax for some dlink dir routers
Abandoning the label and using the function/color syntax for some dlink
dir series routers: dir-1960-a1, dir-2660-a1, dir-2640-a1, dir-3040-a1
and dir-3060-a1

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-09 22:24:31 +02:00
Mieczyslaw Nalewaj
8d7fa09181 ramips: rename include file to a more suitable name
Rename from mt7621_dlink_dir-xx60-a1.dtsi to mt7621_dlink_dir_nand_128m.dtsi
and associated group name when creating the mt7621.mk image

Co-authored-by: Alan Luck <luckyhome2008@gmail.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-09 22:21:39 +02:00
Mieczyslaw Nalewaj
263fde5ab8 ramips: remove unnecessary macros for previous kernel versions
Remove unnecessary 'if' macros for previous kernel versions.
After removing kernel 6.1 the kernel is always >= 6.6 so the conditions
are unnecessary.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[removed some more and also no longer include version.h]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-03 23:02:00 +01:00
Daniel Golle
2967e24d02 ramips: switch to Linux 6.6
Switch to Linux kernel version 6.6 and drop configs, files and patches
for Linux 6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-03 21:36:42 +01:00
Arınç ÜNAL
3ea6125c50 ramips: mt7621-dts: describe switch PHYs and adjust PHY muxing
Currently, the MT7530 DSA subdriver configures the MT7530 switch to provide
direct access to switch PHYs, meaning, the switch PHYs listen on the MDIO
bus the switch listens on. The PHY muxing feature makes use of this.

This is problematic as the PHY may be attached before the switch is
initialised, in which case, the PHY will fail to be attached.

Since commit 91374ba537bd ("net: dsa: mt7530: support OF-based registration
of switch MDIO bus") on mainline Linux, we can describe the switch PHYs on
the MDIO bus of the switch on the device tree.

When the PHY is described this way, the switch will be initialised first,
then the switch MDIO bus will be registered. Only after these steps, the
PHY will be attached.

Describe the switch PHYs on mt7621.dtsi and remove defining the switch PHY
on the SoC's mdio bus node. When the PHY muxing is in use, the interrupts
for the muxed PHY won't work, therefore delete the "interrupts" property on
the devices where the PHY muxing feature is in use.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2024-05-01 13:50:54 +01:00
Arınç ÜNAL
7c9cd43ea2 ramips: mt7621-dts: remove incorrect ethphy4 node for WAVLINK WL-WN573HX1
The ethernet-phy@4 node doesn't exist for WAVLINK WL-WN573HX1. Remove it
and the duplicate gmac0 node.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2024-05-01 13:50:54 +01:00
Arınç ÜNAL
007414aa70 ramips: mt7621-dts: do not modify ethernet node for MeiG SLT866
Currently, the pinctrl-0 property on the ethernet node is modified to
exclude the rgmii1 and rgmii2 pin groups to be claimed with rgmii1 and
rgmii2 functions, respectively. Remove the modification of this property as
we need these pin groups to be claimed with the said functions for this
device.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2024-05-01 13:50:54 +01:00
Shiji Yang
dcdcb9228b generic: MIPS64: fix detect_memory_region() compilation error
1. Enable this feature only for 32-bit CPUs as MIPS64 can not
   access the full range unmapped uncached memory.

2. Backport this fix to the 6.1 old LTS kernel.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-04-30 19:34:02 +02:00
John Audia
dceb5938f8 kernel: bump 6.6 to 6.6.29
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.29

Removed upstreamed:
	generic/backport-6.6/740-v6.9-01-netfilter-flowtable-validate-pppoe-header.patch[1]
	generic/backport-6.6/740-v6.9-02-netfilter-flowtable-incorrect-pppoe-tuple.patch[2]
	generic/backport-6.6/790-29-v6.9-net-dsa-mt7530-fix-improper-frames-on-all-25MHz-and-.patch[3]
	generic/backport-6.6/790-31-v6.10-net-dsa-mt7530-fix-enabling-EEE-on-MT7531-switch-on-.patch[4]
	generic/backport-6.6/790-34-v6.10-net-dsa-mt7530-fix-mirroring-frames-received-on-loca.patch[5]
	generic/backport-6.6/790-35-v6.10-net-dsa-mt7530-fix-port-mirroring-for-MT7988-SoC-swi.patch[6]
	mediatek/patches-6.6/963-net-ethernet-mtk_eth_soc-fix-WED-wifi-reset.patch[7]

Manually rebased:
	generic/backport-6.6/790-23-v6.9-net-dsa-mt7530-get-rid-of-priv-info-cpu_port_config.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=a2471d271042ea18e8a6babc132a8716bb2f08b9
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=4ed82dd368ad883dc4284292937b882f044e625d
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=21b9d89d93422221cdda1b82fd075fa3c94a11d9
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=bd41ee1efd478852a0882ce5f136bc2b5e83eff2
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=d1be3960539249a8690ed09a29d0e3bf34189dd2
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=f8de1b6208bf71bd3102548d33dd8475573ad2ea
7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=6855f724f19620c3ddff57c349e0abba797475b1

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2024-04-28 21:51:03 +02:00
Vince McKinsey
cab2e1de0d ramips: Add support for D-Link DIR-3040 A1
This adds support for the A1 hardware revision of the DIR-3040.
It is an exact copy of the DIR-3060 save for some cosmetic changes to the housing.
Even going so far as having the same FCC ID.

Hardware specification:
SoC: MediaTek MT7621AT
Flash: Winbond W29N01HVSINA 128MB
RAM: Micron MT41K128M16JT-125 256MB
Ethernet: 5x 10/100/1000 Mbps
WiFi1: MT7615DN 2.4GHz N 2x2:2
WiFi2: MT7615DN 5GHz AC 2x2:2
WiFi3: MT7615N 5GHz AC 4x4:4
Button: WPS, Reset

Flash instructions:
OpenWrt can be installed via D-Link Recovery GUI:
NOTE: Seems to only work in Firefox on Windows.
Tried with Chrome on Windows, Firefox in Linux, and Chromium in Linux.
None of these other browsers worked.

    1. Push and hold reset button (on the bottom of the device) until power led
	starts flashing (about 10 secs or so) while plugging in the power cable.
    2. Give it ~30 seconds, to boot the recovery mode GUI
    3. Connect your client computer to LAN1 of the device
    4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
    5. Call the recovery page for the device at http://192.168.0.1/
    6. Use the provided emergency web GUI to upload and flash a new firmware to the device

Thanks to @Lucky1openwrt and @iivailo for creating the DIR-3060 DTS file and related changes,
so it was possible for me to adapt them to the DIR-3040, build images,
test and fix minor issues.

MAC Addresses:

| use | address | example |
| --- | --- | --- |
| LAN | label | f4:*:61 |
| WAN | label + 4 | f4:*:65 |
| WI1/2g | label + 2 | f4:*:63 |
| WI1/5g | label + 1 | f4:*:62 |
| WI2/5g | label + 3 | f4:*:64 |

The label MAC address was found in Factory, 0xe000

Checklist:

✓ nand
✓ ethernet
✓ button
✓ wifi2g
✓ wifi5g
✓ wifi5g
✓ mac
✓ led

Signed-off-by: Vince McKinsey <vincemckinsey@gmail.com>
2024-04-14 20:34:36 +02:00
Mieczyslaw Nalewaj
c08f8a4a49 ramips: add support for TP-Link EC220-G5 v2
TP-Link EC220-G5 v2 is a dual band router with 4 GbE ports
Advertised as AC1200 for its 867Mbps (2x2) 5GHz band
and 300 Mbps (2x2) 2.4GHz band.

Specs:
- SoC: MediaTek MT7620A
- Ethernet: 4x GbE ports (Realtek RTL8367S)
- Wireless 2.4GHz: MediaTek MT7620A
- Wireless 5GHz: MediaTek MT7612E
- RAM: 64MiB
- ROM: 8MiB (W25Q64BV)
- 2 Buttons (WPS and reset)
- 7 LEDs

Flash instructions via serial console:
1. Rename the factory.bin to to test.bin
2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin
3. connect your device to the LAN port
4. power up the router and press 4 on the console to stop the boot process.
5. enter the following commands on the router console
	tftp 0x80060000 test.bin
	erase tplink 0x20000 0x7a0000
	cp.b 0x80060000 0x20000 0x7a0000
	reset

Flash instructions via TFTP:
1. Update orginal firmware of the router to the latest one.
2. Rename openwrt-ramips-mt7620-tplink_ec220-g5-v2-squashfs-tftp-recovery.bin to tp_recovery.bin
3. Change computer IP to 192.168.0.66
4. Run TFTP serwer
5. Start the router with the reset button pressed, the file will be automatically downloaded and after a while the router will restart.
6. After updating, set your computer's IP to DHCP

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-04-13 17:40:51 +02:00
Mieczyslaw Nalewaj
ada3c41acd ramips: mt7620a_tplink_archer.dtsi rename to mt7620a_tplink_8m.dtsi
Change the name mt7620a_tplink_archer.dtsi to mt7620a_tplink_8m.dtsi because it will also be a base for TP-Link non-Archer routers.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-04-13 17:40:51 +02:00
Mieczyslaw Nalewaj
6258492e1b ramips: TP-Link Archer C2 v1: simplification of the dts definition
Import from the mt7620a_tplink_archer.dtsi file and thus simplify the rest of the definition.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-04-13 17:40:51 +02:00