Tested on mt7621 (Redmi AC2100) and running stable for several months.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Jboot devices have problem with >2MB kernelsize. The only way to avoid
this problem is use small loader.
This patch switch all mt7620 Jboot devices to lzma OKLI loader.
Suggested-by: Szabolcs Hubai <szab.hu@gmail.com>
Co-authored-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
BCM4908 devices with U-Boot use pkgtb firmware format. It's based on
U-Boot's FIT: DTB with configurations, images & embedded data.
This format contains bootfs, rootfs and optionally a first stage U-Boot
loader. Contained images need to be extracted & flashed.
Broadcom used two sets of firmwares: main & backup. It uses UBI volumes
"metadata1" & "metadata2" for storing U-Boot env variables with info
about flashed images.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
fdt* utils are needed by targets that use U-Boot FIT images for
sysupgrade. It includes all recent BCM4908 SoC routers as Broadcom
switched from CFE to U-Boot.
fdtget is required for extracting images (bootfs & rootfs) from
Broadcom's ITB. Extracted images can be then flashed to UBI volumes.
sysupgrade is core functionality so it needs dtc as part of base code
base.
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
GL.iNet's U-Boot checks for GPIO 40, not 43.
Changing this allows the RESET button to work as expected.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Daniel Golle <daniel@makrotopia.org>
CC: Li Zhang <li.zhang@gl-inet.com>
HUMAX E10 (also known as HUMAX QUANTUM E10) is a 2.4/5GHz band AC router,
based on MediaTek MT7621A.
Specifications:
- SoC: MT7621A
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB (MXIC MX25L12805D)
- WiFi:
- 2.4GHz: MT7615
- 5GHz: MT7615
- Ethernet: 2x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1x USB 2.0 Type-A
- UART: J1 (57600 8N1)
- pinout: [3V3] (RXD) (GND) (TXD)
Installation via web interface:
- Flash **factory** image through the stock web interface.
Recovery procedure:
1. Connect ethernet cable between Router **LAN** port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
You can use any TFTP client. (tftp, curl, Tftpd64...)
- It can accept both images which is
HUMAX stock firmware dump (0x70000-0x1000000) image
and OpenWRT **sysupgrade** image.
Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
ar9344_openmesh_mr600-v1.dts:40.10-44.5: Warning (gpios_property):
/leds-ath9k/wifi2g: Missing property '#gpio-cells' in node
/ahb/pcie-controller@180c0000/wifi@0,0 or bad phandle
=> added gpio-controller + #gpio-cells
qca955x_zyxel_nbg6x16.dtsi:121.3-13: Warning (reg_format):
/ahb/usb@1b000000/port@1:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
../dts/qca955x_zyxel_nbg6x16.dtsi:131.3-13: Warning (reg_format):
/ahb/usb@1b400000/port@1:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
qca955x_zyxel_nbg6x16.dtsi:120.20-123.4: Warning (avoid_default_addr_size):
/ahb/usb@1b000000/port@1: Relying on default #address-cells value
=> ath79's usb-nodes are missing the address- and size-cells properties.
These are needed for usb led trigger support.
ar7242_ubnt_sw.dtsi:54.4-14: Warning (reg_format): /gpio_spi/gpio_spi@0:reg:
property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
=> the #address-cells and #size-cells had to be nudged.
qca9531_dlink_dch-g020-a1.dts:19.6-39.4: Warning (i2c_bus_bridge):
/i2c: incorrect #size-cells for I2C bus
=> #size-cells = <0>;
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
update rtl8812au-ct driver to be ready for 5.15 Linux.
Signed-off-by: Janpieter Sollie <janpieter.sollie@edpnet.be>
[added commit message from PR with changes, added tag to subject]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
adds the correct offset for the calibration data.
The values are according to the OpenWrt Forum Thread:
"Fritzbox 7430 and wifi".
Link: <https://forum.openwrt.org/t/fritzbox-7430-and-wifi/86944>
Reported-by: RENErica
Signed-off-by: Joel Linn <jl@conductive.de>
[changed commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SoC: AR9344
RAM: 128MB
Flash: 16MiB SPI NOR
5GHz WiFi: AR9382 PCIe 2x2:2 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n
5x Fast ethernet via SoC switch (green LEDs)
1x USB 2.0
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO
UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX
Flash factory image via "emergency room" recovery:
- Configure your computer with a static IP 192.168.1.123/24
- Connect to LAN port on the N600 switch
- Hold reset putton
- Power on, holding reset until the power LED blinks slowly
- Visit http://192.168.1.1/ and upload OpenWrt factory image
- Wait at least 5 minutes for flashing, reboot and key generation
- Visit http://192.168.1.1/ (OpenWrt LuCI) and upload OpenWrt sysupgrade image
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
[dt leds preparations]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The jjPlus JWAP230 is an access point board built around the QCA9558,
with built-in 2.4GHz 3x3 N WiFi (28dBm). It can be expanded with 2
mini-PCIe boards, and has an USB2 root port.
Specifications:
- SOC: Qualcomm Atheros QCA9558
- CPU: 720MHz
- H/W switch: QCA8327 rev 2
- Flash: 16 MiB SPI NOR (en25qh128)
- RAM: 128 MiB DDR2
- WLAN: AR9550 built-in SoC bgn 3T3R (ath9k)
- PCI: 2x mini-PCIe (optional 5V)
- LEDs: 6x LEDs (3 are currently available)
- Button: 1x Reset (not yet defined)
- USB2:
- 1x Type A root port
- 1x combined mini-PCIe
- Ethernet:
- 2x 10/100/1000 (1x PoE 802.3af (36-57 V))
Notes:
The device used to be supported in the ar71xx target.
For upgrades: Please use "sysupgrade --force -n <image>".
This will restore the device back to OpenWrt defaults!
MAC address assignment:
use source
LAN art 0x0
WAN art 0x6
WLAN art 0x1002 (as part of the calibration data)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftp 0x80060000 \
openwrt-ath79-generic-jjplus_jwap230-squashfs-sysupgrade.bin
> erase 0x9f050000 +${filesize}
> cp.b $fileaddr 0x9f050000 $filesize
> setenv bootcmd bootm 0x9f050000
> saveenv
Signed-off-by: Olivier Valentin <valentio@free.fr>
[Added DT-Leds (based on ar71xx), Added more notes about sysupgrade,
fixed "qca9550" to match SoC in commit and dts file name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Chen Minqiang reported in his GitHub PR #4733 that:
With CONFIG_TARGET_INITRAMFS_COMPRESSION_LZMA=y option set,
the popular x86/amd64 target's initramfs-kernel failed to boot.
The cause for this boot failure is that the LZMA compression
uses a the first bytes to encode the compression parameters.
It does not have a fixed magic. Yes, this only works if the
the existing lzma options in the upstream are not changed.
This patch does away with OpenWrt special LZMA options tuning
since it is rather unlikely that upstream will improve the
compression algorithm detection after all this time. Even
though, the tuning produced a smaller initramfs (~1.1% in a
spot check).
Link: <https://github.com/openwrt/openwrt/pull/4733>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* Better product ID for Sophos SG/XG-105 models
* Add support for Sophos SG/XG-135 r1, r2 with/without wireless
Signed-off-by: Stan Grishin <stangri@melmac.ca>
[Changed subject to x86 - probably eaten somewhere, the PR had it]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
NET_DSA_MSCC_FELIX:
Marvell 88E6xxx Ethernet switch fabric support (NET_DSA_MV88E6XXX) [N/m/y/?] n
Ocelot / Felix Ethernet switch support (NET_DSA_MSCC_FELIX) [N/m/y/?] (NEW)
Error in reading or end of file.
make[6]: *** [scripts/kconfig/Makefile:71: syncconfig] Error 1
make[5]: *** [Makefile:603: syncconfig] Error 2
IR_IMON_RAW:
SoundGraph iMON Receiver (early raw IR models) (IR_IMON_RAW) [N/m/?] (NEW)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[squashed with "kernel: add missing IR_IMON_RAW config symbol"]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The 'fils_dhcp' option can be set to '*' in order to autodetect the DHCP server
For proto=dhcp networks, the discovered dhcp server will be used
For all other networks, udhcpc is called to discover the address
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Among other things, this can be used to auto-configure the DHCP server
address for wireless APs using FILS, if the bridged interface is
configured to DHCP
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixed -no-pie compilation warning on MacOS
Fixed errors related to using absolute addressing on MacOS arm64
Based on upstream patch from Jessica Clarke and suggestions from Ronny Kotzschmar
Link to original patch and discussion:
3b142045e8
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
Zbtlink ZBT-WG1602 is a Wi-Fi router intendent to use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offsers a couple of miniPCIe
slots with USB and SIM only and another one pure miniPCIe slot as well
as five Gigabit Ethernet ports (4xLAN + WAN).
Specification:
* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB (SPI NOR)
* external watchdog (looks like Torexsemi XC6131B)
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603EN (.11n, MIMO 2x2)
* WLAN 5GHz: MT7612EN (.11ac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 2.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled, 1
power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)
Additional HW information:
* SoC USB port #1 is shared by internal miniPCIe slot and external
Type-A USB port, USB D+/D- lines are toggled between ports using a
GPIO controlled DPDT switch.
* Power of the USB enabled miniPCIe slots can be individually controlled
using dedicated GPIO lines.
* Vendor firmware feeds the external watchdog with 1s pulses. GPIO
watchdog driver is able to either generate a 1us pulses or toggle the
output line. 1us is not enough for the external watchod timer, so
the line toggling driver mode is utilized.
Installation:
Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
be directly used to install OpenWrt. Firmware must be upgraded using the
'force' and 'do not save configuration' command line options (or
correspondig web interface checkboxes) since the vendor firmware is from
the pre-DSA era.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
TP-Link EAP225 v1 is an AC1200 (802.11ac Wave-1) ceiling mount access point.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9882): a/n/ac, 2x2
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE
Flashing instructions:
* Ensure the device is upgraded to firmware v1.4.0
* Exploit the user management page in the web interface to start telnetd
by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`.
* Immediately change the malformed username back to something valid
(e.g. 'admin') to make ssh work again.
* Use the root shell via telnet to make /tmp world writeable (chmod 777)
* Extract /usr/bin/uclited from the device via ssh and apply the binary
patch listed below. The patch is required to prevent `uclited -u` in
the last step from crashing.
* Copy the patched uclited binary back to the device at /tmp/uclited
(via ssh)
* Upload the factory image to /tmp/upgrade.bin (via ssh)
* Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt.
uclited patching:
--- xxd uclited
+++ xxd uclited-patched
@@ -53811,7 +53811,7 @@
000d2330: 8c44 0000 0320 f809 0000 0000 8fbc 0010 .D... ..........
000d2340: 8fa6 0a4c 02c0 2821 8f82 87c4 0000 0000 ...L..(!........
-000d2350: 8c44 0000 0c13 461c 27a7 0018 8fbc 0010 .D....F.'.......
+000d2350: 8c44 0000 2402 0000 0000 0000 8fbc 0010 .D..$...........
000d2360: 1040 001d 0000 1821 8f99 8378 3c04 0058 .@.....!...x<..X
000d2370: 3c05 0056 2484 ad68 24a5 9f00 0320 f809 <..V$..h$.... ..
To make sure the correct file is patched, the following MD5 checksums
should match the unpatched and patched files:
4bd74183c23859c897ed77e8566b84de uclited
4107104024a2e0aeaf6395ed30adccae uclited-patched
Debricking:
* Serial port can be soldered on unpopulated 4-pin header
(1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors running from pins 1 (TXD) and 2 (RXD).
Do NOT bridge the pull-down for pin 2, running parallel to the
header.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via the LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
Tested by forum user KernelMaker.
Link: https://forum.openwrt.org/t/eap225-v1-firmware/87116
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Mac adresses are assigned in the order given by the port list. The
interfaces are also brought up in this order. This target supports
devices with up to 52 ports. Sorting these alphabetically is very
confusing, and assigning mac addresses in alphabetic order does not
match stock firmware behaviour.
Suggested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The Realtek Otto watchdog timer driver was accepted upstream, and is
queued for 5.17. Update the patch's file name, and replace by the final
version.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Added support to generate dynamic-sized VHDX images for Hyper-V.
Compile-tested on x86 and run-tested on Windows 10 21H2 (Hyper-V).
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
change meson binary to use py extension. Fixes issue with meson's
symbolextractor using the host python instead of the system one.
We intentionally use a .py extension here so that meson launches
additional python scripts with the same build host python interpreter as
itself is running under (and not the host package one once it becomes
available)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
By default CONFIG_BTRFS_FS_POSIX_ACL is disabled, it should be enabled
only when you enable CONFIG_FS_POSIX_ACL.
Right now, when you enable CONFIG_FS_POSIX_ACL it will enable
CONFIG_BTRFS_FS_POSIX_ACL, but it will be disabled once you install
kmod-btrfs. This should prevent it.
Btrfs has enabled by default ACL for mount option.
More details:
https://cateee.net/lkddb/web-lkddb/BTRFS_FS_POSIX_ACL.htmlhttps://btrfs.wiki.kernel.org/index.php/Manpage/btrfs(5)
Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Revert the SDC "CLK_SET_RATE_GATE" changes to the SDC clock regulator
structures.
See https://elinux.org/images/b/b8/Elc2013_Clement.pdf
> if ((clk->flags & CLK_SET_RATE_GATE) && clk->prepare_count) {
>
> For this particular clock, setting its rate is possible only if the
> clock is ungated (not yet prepared)
This fixes the MMC failing to initialize on newer ZyXEL NBG6817
hardware revisions with Kingston MMC. Older revisions should
hopefully be unaffected.
Check MMC hardware details with:
cd /sys/block/mmcblk0/device/ && \
tail -v cid date name manfid fwrev hwrev oemid rev
Known problematic MMC names (broken before this commit):
* M62704 (dated 12/2018) via myself
* M62704 (dated 11/2018) via Drake Stefani
Known unaffected MMC names (already working without this commit):
* S10004 (dated 12/2015) via slh
Without enabling dynamic debugging, this error manifests in the kernel
hardware serial console as the following:
[ 2.746605] mmc0: error -110 whilst initialising MMC card
[…trimmed other messages…]
[ 2.877832] Waiting for root device /dev/mmcblk0p5...
Enabling Linux dynamic kernel debugging provides additional messages.
For guidance, see the Linux kernel documentation:
https://www.kernel.org/doc/html/latest/admin-guide/dynamic-debug-howto.html
First, enable dynamic debugging in OpenWRT's configuration:
1. Run "make menuconfig"
2. Select "Global build settings --->"
3. Select "Kernel build options --->"
4. Enable "Compile the kernel with dynamic printk" via spacebar
5. Save and exit (arrow key to "Exit" until prompted to save, save)
Alternatively, set "CONFIG_KERNEL_DYNAMIC_DEBUG=y" in your .config.
Then, turn on dynamic debugging at boot:
Modify bootargs in
target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
to add…
bootargs = "[…existing bootargs…] dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8";
For example:
chosen {
- bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1";
+ bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1 dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8";
append-rootblock = "root=/dev/mmcblk0p";
Then, compile and flash the resulting build. If you are testing
before this commit on newer MMC hardware, be prepared to recover!
NOTE: If you have hardware serial console access, you don't need to
use TFTP recovery to change the active boot partition.
Reboot to working alternative partition via serial console:
1. Connect to hardware serial console
* See https://openwrt.org/toh/zyxel/nbg6817#serial
2. Interrupt boot at "Hit any key to stop autoboot:"
3. Run "ATSE NBG6817"
4. Copy the result (e.g. "001976FE4B04")
* Changes with **every boot** - can't reuse this
5. On your local system, run
"./zyxel-uboot-password-tool.sh <copied value here>"
* Example: "./zyxel-uboot-password-tool.sh 001976FE4B04"
6. Run the command provided by the password tool
* Example: "ATEN 1,910F129B"
* Changes with **every boot** - can't reuse this
7. Run "ATGU"
* You now have full u-boot shell until next boot - unlocking is
not remembered
8. Run either "run boot_mmc" (for booting partition set "FF") or
"run boot_mmc_1" (for booting partition set "01")
* These commands are not affected by dual-boot partition flags
NOTE: This will NOT set the dual-boot partition flag. You'll need to
fix that manually. The "nbg6817-dualboot" script may help:
https://github.com/pkgadd/nbg6817/blob/master/nbg6817-dualboot
zyxel-uboot-password-tool.sh - sourced from
commit 459c8c9ef8:
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ a ))
printf "ATEN 1,%X\n" $p
Kernel serial console log BEFORE commit with dynamic debug enabled:
[…trimmed…]
[ 3.171343] mmci-pl18x 12400000.sdcc: designer ID = 0x51
[ 3.171397] mmci-pl18x 12400000.sdcc: revision = 0x0
[ 3.175811] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz
[ 3.181134] mmci-pl18x 12400000.sdcc: No vqmmc regulator found
[ 3.186788] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio)
[ 3.192902] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2
[ 3.215609] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0
[ 3.227532] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v
[ 3.247518] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0
[…trimmed…]
[ 3.997725] mmc0: req done (CMD2): -110: 00000000 00000000 00000000 00000000
[ 4.003631] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000
[ 4.003659] mmc0: error -110 whilst initialising MMC card
[ 4.016481] mmc0: clock 0Hz busmode 2 powermode 0 cs 0 Vdd 0 width 1 timing 0
Notice how the initial clock is 52 MHz, which is incorrect - MMC
requires negotiation to enable higher speeds.
Kernel serial console log AFTER commit with dynamic debug enabled:
[…trimmed…]
[ 3.168996] mmci-pl18x 12400000.sdcc: designer ID = 0x51
[ 3.169051] mmci-pl18x 12400000.sdcc: revision = 0x0
[ 3.173492] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz
[ 3.178808] mmci-pl18x 12400000.sdcc: No vqmmc regulator found
[ 3.184702] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio)
[ 3.190573] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2
[ 3.217873] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0
[ 3.229250] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v
[ 3.249111] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0
[…trimmed…]
[ 4.392652] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000
[ 4.392785] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 1
[ 4.406554] mmc0: starting CMD6 arg 03b70201 flags 0000049d
[…trimmed…]
Now, the MMC properly initializes and later switches to high speed.
Thanks to:
* Ansuel for maintaining/help with the IPQ806x platform, kernel code
* slh for additional debugging and suggestions
* dwfreed for confirming newer MMC details, clock frequency
* robimarko for device driver debug printing help, clock debugging
* Drake for testing and confirmation with their own newer NBG6817
...and anyone else I missed!
Signed-off-by: Shane Synan <digitalcircuit36939@gmail.com>
Tested-by: Shane Synan <digitalcircuit36939@gmail.com>
BMT replaces nand-specific ops for erasing and writing, but the
mtk-snand driver only implements generic mtd api.
Replace erase, block_isbad, block_markbad in mtd_info for generic mtd
drivers.
Fixes: b600aee3ed ("mediatek: attach bmt to the new snand driver")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The following command checks if a instance of a service is running.
/etc/init.d/<service> running <instance>
In the variable `$@`, which is passed to the function
`service_running`, the first argument is always the `instance` which
should be checked. Because all other variables where removed from `$@`
with `shift`.
Before this change the first argument of `$@` was set to the `$service`
Variable. So the function does not work as expected. The `$service`
variable was always the instance which should be checked. This is not
what we want.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
ipTIME A3004NS-dual is a 2.4/5GHz band router, based on Mediatek MT7621.
Specifications:
- SoC: MT7621 (880MHz)
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7602E
- 5GHz : MT7612E
- Ethernet:
- 4x LAN
- 1x WAN
- USB: 1 * USB3.0 port
- UART:
- 3.3V, TX, RX, GND / 57600 8N1
Installation via web interface:
- 1. Flash Initramfs image using OEM Firmware's web GUI
- 2. Boot into OpenWrt and perform Sysupgrade with sysupgrade image.
Revert to stock firmware:
- 1. Boot into OpenWrt and perform Sysupgrade with OEM Stock Firmware image.
Signed-off-by: Yuchan Seo <hexagonwin@disroot.org>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Currently it is not possible to configure VLANs via LUCI on
tplink tl-mr3020-v3. This patch fixes switch topology for the
LUCI interface.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
[copied commit message from github PR]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In 20b09a2125 Lava LR-25G001 router have problem with two inactive
ethernet ports. JBOOT bootloader didn't configure ethernet devices by default.
The same situation was there. It is required to enable all phy ports.
This is fragment of stock bootlog:
switch reg write_athr offset=90, value=2b0
switch reg write_athr offset=8c, value=2b0
switch reg write_athr offset=88, value=2b0
switch reg write_athr offset=84, value=2b0
switch reg write_athr offset=80, value=2b0
This patch adds proper registers configuration ar8337 initvals.
0x2b0 value causes force flow control configuration, 0x1200 was used
instead (flow control config auto-neg with phy). [1]
When switch is now ok, let's fix port numeration too.
Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")
[1] https://github.com/openwrt/openwrt/pull/4806#issuecomment-982019858
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
introduce nvmem pre-cal + mac-address cells for both Wifis
and ethernet on the EZVIZ CS-W3-WD1200G EUP. This is one of
the few devices in which the correct mac adress is already
at the right place for Wifi, so no separate nvmem cell is
needed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
with current images, the device is no longer booting.
It gets stuck in the bootloader with "Config not available"
and drops to the uboot shell.
|flash_type: 0
|Hit any key to stop autoboot: 0
|SF: Detected MX25L12805D with page size 4 KiB, total 16 MiB
|Config not availabale
|(IPQ40xx) #
This is because the default bootcmd "bootipq" will only read
the first four MiB of the kernel image. With 5.10 the gzip'd
kernel is slightly larger. So the part of the FIT image which
had the configuration is cut off. Hence it can't find it.
To update the bootcmd, you have to attach the serial console
again and enter the following commands into the boot prompt:
# setenv bootcmd "sf probe; sf read 84000000 180000 600000; bootm"
# saveenv
# run bootcmd
This will allow booting kernels with up to six MiB. This also
allows us to drop the DEVICE_DTS_CONFIG hack we had to use.
Note:
uboot doesn't support LZMA. It fails with:
"Unimplemented compression type 3"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The itian sq201, raidsonic ib-4220-b and storlink sl93512r
can't boot from ext4. This is because the rootfstype in the
device-tree bootargs is set to "squashfs,jffs2". (And ext4
was not designed for raw NOR flash chips).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
