switch-bcm53xx-mdio does not exists, use kmod-switch-bcm53xx-mdio
instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Tobias Schramm <tobleminer@gmail.com>
- Delete useless HDD presence inputs: they aren't buttons, and probably
they are outputs in the stock firmware.
- Change the Function Button keycode: the current one isn't mapped by
the kernel module.
- Use the recommended property names for the ethernet stuff.
- Add missing i2c pinmux.
- Minor cosmetic changes.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
All boards on xrx200 use builtin switch and there is no supported device
with external switch.
It was copy paste from xway subtarget and was added in commit 18b76c66fb.
Save 20.3 kB flash memory.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
This is fixed in 18.06, it appears again in 19.07.
Currently mt7628 sdcard driver do not support polling mode which is for
the device do not have card-detect pin to detect sd card insert. Without
this patch, device will not detect sdcard is inserted. This patch is a
fix of that.
Signed-off-by: Qin Wei <support@vocore.io>
Removing i2c pxa slave
The i2c-pxa is typically not use in slave mode. It does not make sense
to have slave mode enabled by default.
Having slave mode enabled prevents the i2c controller from being reset
if a real slave device such as an SFP is attached to the i2c-pxa bus and
locks it up.
Disable slave mode so that the i2c controller can be reset if the bus is
locked up.
If someone actually has a need for pxa slave mode this can be enabled in
kernel config.
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
/lib/netifd/dhcp.script:
Keep support for 'timesvr' while also supporting 'timesrv'
Add log message indicating deprecation of 'timesvr'
Signed-off-by: Sukru Senli <sukru.senli@iopsys.eu>
the uboot of nsa310 cannot use the network chip
as it is a realtek on the PCIe lanes and not a
Marvell ethernet from the SoC.
Therefore tftp is not possible on this device
and the only way to install is by loading files
from a USB drive.
If the USB subsystem is dead there is no way to
install OpenWrt.
Enable sata support and commands so it can be
used as a fallback in case of USB issues.
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
With package "coreutil-sha256sum" installed "sysupgrade" fails to perform 'sha256sum -s' and instead returns 'invalid option -- 's''.
This is caused due to:
different syntax for a sha256sum status check ('sha256sum --status' with "coreutil-sha256sum")
'/usr/bin/sha256sum' being symlinked to '/usr/bin/gnu-sha256sum' (after installation of "coreutil-sha256sum")
"coreutil-sha256sum" package from the packages feed replaces the Busybox sha256sum
This patch restores for 'sysupgrade' the busybox call to its sha256sum applet.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Support Intel 10 Gigabit Ethernet Cards in x86/64 images by default.
This ensures that systems with cards such as the Intel x520 will work properly.
Signed-off-by: Gregory L. Dietsche <Gregory.Dietsche@cuw.edu>
With this change the LED subsystem is abused in the kernel to switch the
simswap. This change will be reverted, so we could use again the gpio
subsystem.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Add a module description for the new pcengnies-apu2 device driver.
This driver supports the front button and LEDs on the PC Engines
APUv2/APUv3 boards.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Remove leds-apu2 out of tree driver. There is a new upstream device gpio
and leds driver stack available for the APUv2 and APUv3 boards from pc
egnines. This new driver stack was add in kernel version 4.15.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.
The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi
Note that while this tidies up master a lot, it might develop into a
frequent pitfall for backports.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
chosen/bootargs are defined to the same value in device DTS files
that is already set in the SoC DTSI. Remove the redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ath9k will already fallback on software-crypto for chipsets not
supporting IEEE802.11w (MFP). So advertising MFP is not dependent
on disabling HW crypto for all traffic entirely.
Tested on Sonicwall SonicPoint Ni (AR9132)
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for the AVM FRITZ!WLAN Repeater DVB-C
SOC: Qualcomm Atheros QCA9556
RAM: 64 MiB
FLASH: 16 MB SPI-NOR
WLAN: QCA9556 3T3R 2.4 GHZ b/g/n and
QCA9880 3T3R 5 GHz n/ac
ETH: Atheros AR8033 1000 Base-T
DVB-C: EM28174 with MaxLinear MXL251 tuner
BTN: WPS Button
LED: Power, WLAN, TV, RSSI0-4
Tested and working:
- Ethernet (correct MAC, gigabit, iperf3 about 200 Mbit/s)
- 2.4 GHz Wi-Fi (correct MAC)
- 5 GHz Wi-Fi (correct MAC)
- WPS Button (tested using wifitoggle)
- LEDs
- Installation via EVA bootloader (FTP recovery)
- OpenWrt sysupgrade (both CLI and LuCI)
- Download of "urlader" (mtd0)
Not working:
- Internal USB
- DVB-C em28174+MxL251 (depends on internal USB)
Installation via EVA bootloader (FTP recovery):
Set NIC to 192.168.178.3/24 gateway 192.168.178.1 and power on the device,
connect to 192.168.178.1 through FTP and sign in with adam2/adam2:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Wait for "Transfer complete" together with the transfer details.
Wait two minutes to make sure flash is complete (just to be safe).
Then restart the device (power off and on) to boot into OpenWrt.
Revert your NIC settings to reach OpenWrt at 192.168.1.1
Signed-off-by: Natalie Kagelmacher <nataliek@pm.me>
[fixed sorting - removed change to other board -
prettified commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport patches which fix compile issue for uClibc-ng :
dbrandom.c:174:8: warning: implicit declaration of function 'getrandom'; did you mean 'genrandom'? [-Wimplicit-function-declaration]
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~
genrandom
dbrandom.c:174:36: error: 'GRND_NONBLOCK' undeclared (first use in this function); did you mean 'SOCK_NONBLOCK'?
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~~~~~
SOCK_NONBLOCK
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
- update SPDX license identifier
- use https in URL
- use default PKG_BUILD_DIR
Suggested-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Tested-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Read the freifunk packages, that have been moved from the LuCI feed
into its own feed in January 2019.
Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
* compat: drop centos 8.1 support as 8.2 is now out
Of note, as well, is that we now have both RHEL7 and RHEL8 in our CI at
<https://www.wireguard.com/build-status/>.
* Kbuild: remove -fvisibility=hidden from cflags
This fixes an issue when compiling wireguard as a module for ARM kernels in
THUMB2 mode without the JUMP11 workaround.
* noise: do not assign initiation time in if condition
Style fix.
* device: avoid circular netns references
Fixes a circular reference issue with network namespaces.
* netns: workaround bad 5.2.y backport
This works around a back backport in the 5.2.y series.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
mac80211_get_addr is called from mac80211_generate_mac, where the local variable
initialisation id="${macidx:-0}" suggests that macidx is not always defined.
Probably, idx was supposed to be used instead of $(($macidx + 1)).
Fixes: 4d99db168c ("mac80211: try to get interface addresses from wiphy sysfs 'addresses' if no mask is set")
Signed-off-by: Leon M. George <leon@georgemail.eu>
This patch adds supports for the NETGEAR R6200 V1
This device is mainlined in Linux as of 5.4
Specification:
- SOC: Broadcom BCM4718A1 (480 MHz)
- Flash: 16MB (Macronix MX25L128)
- RAM: 128MB DDR2
- SWITCH: BCM53125
- Ethernet: 5x GE (1 WAN + 4 LAN, Inverted order)
- WLAN 2.4G: In SOC
- WLAN 5GHz: miniPCIe card, BCM4352 (ID: 4360)
- USB: 1x USB 2.0 port (Type A)
- Buttons: Reset, WLAN, WPS
- LED: Amber for Power, others need a workaround
- UART: 1x UART on PCB
LED Issues: They are controlled by a 74HC164 via bit banging(GPIO 6/7)
Firmware Install Instructions
=============================
Using the device specific .chk, use that file to perform
a normal device upgrade in the OEM admin page.
Signed-off-by: Edward Matijevic <motolav@gmail.com>
urandom-seed has a separate Makefile, we can safely remove the definition here.
Fixes: 27bfde9c9f ("base-files: move urandom seed bits into separate package")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit performs minor janitorial work to clean up some code
formatting for the Netgear R6120.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
This moves the trigger for the Netgear R6120's wlan2g_green LED from
base-files/etc/board.d/01_leds to the device-tree file.
This has been applied to R6120 based on findings for the very similar
Netgear R6080.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[merge case in 01_leds, slightly adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (armada-3720-uDPU.dts), which is only present
for 4.19, as it has been upstreamed before 5.4.
Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory, only keeping
the named exception to files-4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (qcom-ipq4018-emr3500.dts), which is only
present for 5.4.
Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory.
If there ever was a new kernel with substantial DTS changes, a
new folder would need to be introduced anyway and could easily be
done.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"[[" is a bash extension for test. As the ash-implementation is not
fully compatible we drop its usage.
This follows up 3519bf4976
As a result, we also need to move the and/or out of the test brackets.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[squash from two patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The original text was copy/pasted from some other package.
Adjust the package title and description to match the description
on the publishers page.
Signed-off-by: Catalin Patulea <catalinp@google.com>
[slightly adjust content and commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The mwlwifi driver sets the default country code for EU (fi-
rmware region code 0x30) certified devices to FR (France),
not DE (Germany). Whilst this is a trivial fix, novice users
may not know how mwlwifi negatively reacts to a non-matching
country code and may leave the setting alone. Especially si-
nce it is under the advanced settings section in LuCI.
Relevant mwlwifi driver code:
0a550312dd
The mwlwifi driver readme states "Please don't change country
code and let mwlwifi set it for you." However, OpenWrt's current
behaviour does not adhere to this with its default, 'just flashed
from factory' setting for EU devices.
Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upstream in commit f9f8f0c24203 ("crypto: ccp -- don't "select"
CONFIG_DMADEVICES") removed dependency on CONFIG_DMADEVICES symbol which
leads to build breakage of ccp crypto module, so fix this by adding that
symbol back in the kernel config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The ADB P.DG AV4202N device has a wifi chipset connected via PCI. But the
PCI pinmux is missing and without it the wifi won't work properly.
Add the pinctrl_pci to enable the missing PCI pins for this device.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Currently it's not possible to tftpboot initramfs image on archer-c7-v5
as the image contains tplink-v1-header which leads to:
ath> bootm
## Booting image at 81000000 ...
Bad Magic Number
as U-Boot expects uImage wrapped image. This is caused by following
inheritance issue:
define Device/Init
KERNEL_INITRAMFS = $$(KERNEL)
define Device/tplink-v1
KERNEL := kernel-bin | append-dtb | lzma
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | tplink-v1-header
define Device/tplink-safeloader
$(Device/tplink-v1)
define Device/tplink-safeloader-uimage
$(Device/tplink-safeloader)
KERNEL := kernel-bin | append-dtb | lzma | uImageArcher lzma
define Device/tplink_archer-c7-v5
$(Device/tplink-safeloader-uimage)
where tplink-v1 defines KERNEL_INITRAMFS with tplink-v1-header and it's
then used by all devices inheriting from tplink-safeloader. Fix this by
overriding KERNEL_INITRAMFS to KERNEL variable again.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
- drop patches (applied upstream):
* 010-backport-change-address-logging.patch
* 020-backport-ed25519-support.patch
* 021-backport-chacha20-poly1305-support.patch
- backport patches:
* 010-backport-disable-toom-and-karatsuba.patch:
reduce dropbear binary size (about ~8Kb).
- refresh patches.
- don't bother anymore with following config options
because they are disabled in upstream too:
* DROPBEAR_3DES
* DROPBEAR_ENABLE_CBC_MODE
* DROPBEAR_SHA1_96_HMAC
- explicitly disable DO_MOTD as it was before commit a1099ed:
upstream has (accidentally) switched it to 0 in release 2019.77,
but reverted back in release 2020.79.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.
The previous patch in 36f628910b was only applied to the 4.19 file,
so let's just make it consistent with this patch.
Cc: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Inputs assigned to "mode select" switch on the side of the device
were missing linux,input-type property.
This would cause them do incorrectly generate EV_KEY events.
Fix this by setting the linux,input-type = <EV_SW> property on them.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Increase the SPI frequency for ELECOM WRC-1900GST and WRC-2533GST
to 40 MHz by updating the common DTSI file.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[WRC-1900GST]
Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link CPE610 v2 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of DDR2 RAM
- 8 MB of SPI-NOR Flash
- 23dBi high-gain directional 2×2 MIMO antenna and a
dedicated metal reflector
- Power, LAN, WLAN5G green LEDs
- 3x green RSSI LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This ports support for these devices from ar71xx.
Specification:
- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: v3: 560 MHz, v4: 650 MHz
- Flash: 4096 KiB
- RAM: 32 MiB
- Ethernet: 1 port @ 100M
- Wireless: SoC-integrated: QCA9533 2.4GHz 802.11bgn
In contrast to the implementation in ar71xx (reset and WiFi button),
the device actually features reset and WPS buttons.
Flashing instructions:
Upload the ...-factory.bin file via OEM web interface.
TFTP Recovery:
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to
wa801ndv3_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
TFTP recovery has only been tested with v3, and the Wiki states
that the procedure won't work for v4, which cannot be verified
or falsified at the moment.
Tested by Tim Ward (see forum):
https://forum.openwrt.org/t/ath79-support-for-tp-link-tl-wa901nd-v3-v4-v5/61246/13
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix the switch LAN labels for the DGND3700v1/DGND3800B router,
the order is reversed.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[cut out of bigger patch, adjust commit title/message accordingly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Huawei Echolife HG622 has hardware controlled LAN LEDs.
Add the ephy led pinctrl to let the router show LAN activity on these
LEDs.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
