Linux MTD requires the parent partition be writable for a child
partition to be allowed write permission.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Update this pending patch to remove the untested (variable eraseregions)
section, alongside simplifying the patch.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[refresh and split out unrelated refreshes]
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Since 4e0c54bc5b ("kernel: add support for kernel 5.4"),
the spi-nor limit 4k erasesize to spi-nor chips below a configured size
patch has not functioned as intended.
For uniform erasesize SPI-NOR devices, both
nor->erase_opcode & mtd->erasesize are used in erase operations.
These are set before, and not modified by, this
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS_LIMIT patch.
Thus, an SPI-NOR device with CONFIG_MTD_SPI_NOR_USE_4K_SECTORS will
always use 4k erasesize (where the device supports it).
If this patch was fixed to function as intended, there would be
cases where devices change from a 4K to a 64K erasesize.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Asus RP-AC87 ac2600 Repeater
2.4GHz 800Mbps
5GHz 1733Mbps
Hardware specifications:
SoC: MT7621A 2 cores 4 threads @880MHz
WiFi2G: MT7615E 2G 4x4 b/g/n
Wifi5G: MT7615E 5G 4x4 n/ac
DRAM: 128MB DDR3 @1200mhz
Flash: 16MB MX25L12805D SPI-NOR
LAN/WAN: MT7530 1x1000M
MAC addresses as verified by OEM firmware:
use address source
Lan/W5G *:B0 factory 0x8004 (label)
W2G *:B4 factory 0x0
Installation:
Asus windows recovery tool:
install the Asus firmware restoration utility
unplug the router, hold the reset button while powering it on
release when the power LED flashes slowly
specify a static IP on your computer:
IP address: 192.168.1.75
Subnet mask 255.255.255.0
Start the Asus firmware restoration utility, specify the factory image
and press upload
Do not power off the device after OpenWrt has booted until the LED flashing.
TFTP Recovery method:
set computer to a static ip, 192.168.1.2
connect computer to the LAN 1 port of the router
hold the reset button while powering on the router for a few seconds
send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put factory.bin
tftp> quit
Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
OpenWrt now uses firewall4 (nft) by default,
so iptables should also default to nftables backend.
When multiple packages provide the same virtual package,
opkg pick the first one by alphabetical order,
so we rename iptables-legacy to iptables-zz-legacy and add
iptables-legacy in PROVIDES.
We also need to remove IPTABLES_NFTABLES config as
this cause recursive dependencies.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
The random crashes observed with HARDENED_USERCOPY enabled no longer
seem to occur. Enable HARDENED_USERCOPY to improve security.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This patch provides support for the Firebox M300 only user-controllable
bi-color LED, and makes the green "shield" LED act as the typical
OpenWrt status led.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Kernel 5.15.49 introduced a new symbol 'LIB_MEMNEQ'. Add it to the
generic 5.15 config.
Fixes: f1cd144482 ("kernel: bump 5.15 to 5.15.49")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Kernel 5.10.124 introduced a new symbol 'LIB_MEMNEQ'. Add it to the
generic 5.10 config.
Fixes: 9e5d743422 ("kernel: bump 5.10 to 5.10.124")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
DGS-1210 switches support dual image, with each image composed of a
kernel and a rootfs partition. For image1, kernel and rootfs are in
sequence. The current OpenWrt image (written using a serial console),
uses those partitions together as the firmware partition, ignoring the
partition division. The current OEM u-boot fails to validate image1 but
it will only trigger firmware recovery if both image1 and image2 fail,
and it does not switch the boot image in case one of them fails the
check.
The OEM factory image is composed of concatenated blocks of data, each
one prefixed with a 0x40-byte cameo header. A normal OEM firmware will
have two of these blocks (kernel, rootfs). The OEM firmware only checks
the header before writing unconditionally the data (except the header)
to the correspoding partition.
The OpenWrt factory image mimics the OEM image by cutting the
kernel+rootfs firmware at the exact size of the OEM kernel partition
and packing it as "the kernel partition" and the rest of the kernel and
the rootfs as "the rootfs partition". It will only work if written to
image1 because image2 has a sysinfo partition between kernel2 and
rootfs2, cutting the kernel code in the middle.
Steps to install:
1) switch to image2 (containing an OEM image), using web or these CLI
commands:
- config firmware image_id 2 boot_up
- reboot
2) flash the factory_image1.bin to image1. OEM web (v6.30.016)
is crashing for any upload (ssh keys, firmware), even applying OEM
firmwares. These CLI commands can upload a new firmware to the other
image location (not used to boot):
- download firmware_fromTFTP <tftpserver> factory_image1.bin
- config firmware image_id 1 boot_up
- reboot
To debrick the device, you'll need serial access. If you want to
recover to an OpenWrt, you can replay the serial installation
instructions. For returning to the original firmware, press ESC during
the boot to trigger the emergency firmware recovery procedure. After
that, use D-Link Network Assistant v2.0.2.4 to flash a new firmware.
The device documentation does describe that holding RESET for 12s
trigger the firmware recovery. However, the latest shipped U-Boot
"2011.12.(2.1.5.67086)-Candidate1" from "Aug 24 2021 - 17:33:09" cannot
trigger that from a cold boot. In fact, any U-Boot procedure that relies
on the RESET button, like reset settings, will only work if started from
a running original firmware. That, in practice, cancels the benefit of
having two images and a firmware recovery procedure (if you are not
consider dual-booting OpenWrt).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
The cameo header is a 0x40-byte header used by D-Link DGS 1210 switches
and Apresia ApresiaLightGS series. cameo-imghdr.py is a clean-room
reimplementation of imghdr present in the DGS-1210-28-GPL package.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[fix board_version argument's help text]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Enabling mbo by default on 802.11ax devices breaks for encryption types
that do not enable 802.11w by default. Disable mbo by default to fix
this. Enabling mbo by default on 802.11ax devices was not explained in
the commit message anyway.
Fixes: 6eee983656 ("hostapd: introduce mbo option")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This model is almost identical to the EAP225 v3.
Major difference is the RTL8211FS PHY Chipset.
Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (RTL8211FS): 1× 1GbE, 802.3at PoE
Flashing instructions:
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
Do NOT bridge R230.
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via LuCI web interface
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
Signed-off-by: Sven Hauer <sven.hauer+github@uniku.de>
Introduce a new option background_radar to toggle hostapd's background
radar feature. Enabling this allows DFS CAC to run on dedicated radio RF
chains while the radio(s) are otherwise running normal AP activities on
other channels.
As OpenWrt configures hostapd to use a channel list even when a single
channel is configured, using this feature requires a list of channels in
/etc/config/wireless. Alternatively, channel can be set to auto.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Support the use of MBO in the bss_transition_request ubus method.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Introduce a new option mbo to toggle Multi Band Operation aka Agile
Multiband for a BSS.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Multi Band Operation is required for 802.11ax certification, so let's
enable it if 802.11ax support is enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Multi Band Operation aka Agile Multiband introduces new Transition
and Transition Rejection Reason Codes that should improve client
steering. Add a config symbol to enable it, and enable it by default for
the full variants.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
In Linux v5.14 an extra feature was introduced for the RTL8211F phy,
allowing to disable a clock output from the phy. Part of that patch is to
always (soft) reset the phy upon initialisation.
This phy reset is required to have a working ethernet on the TP-Link
EAP225-Outdoor v3 and EAP225 v4 after a reboot. Otherwise the ethernet
port will only function properly on cold boots.
Tested-by: Andre Klärner <kandre@ak-online.be> # EAP225-Outdoor v3
Tested-by: Sven Hauer <sven.hauer+github@uniku.de> # EAP225 v4
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The support-list partition for the EAP225-V3 board ID became larger than
the allocated size, resulting in factory image generation for the
EAP225-Outdoor v3 and EAP225 v3 to fail. The make directive
Build/tplink-safeloader ignores this failure however, resulting in a
seemingly successful build with empty factory images.
Included changes:
e609c5d75186 tplink-safeloader: drop unqualified EAP225-V3 IDs
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Enable ath10k offload by default. This improves wireless performance
without requiring user configuration.
This adds ath10k_core to the AUTOLOAD section so that the frame_mode
paramter can be added to /etc/modules.d and passed to the driver.
The frame_mode 2 enables ethernet mode on the firmware/driver.
This parameter is set by passing a different value to the frame_mode
value on kmod insmod.
Link to the original patchset:
https://patchwork.kernel.org/project/linux-wireless/cover/20220516032519.29831-1-ryazanov.s.a@gmail.com/
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
lantiq,bus-clock, interrupt-map-mask and interrupt-map are already
defined with these exact values in vr9.dtsi. Drop them from
vr9_tplink_tdw8980.dts to just have one place where these are
maintained.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Starting with GCC 12, we have the possibility of mitigating straight-line
speculation vulnerabilities in x86-64 targets. Make it so.
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
No patches required a rebase, just updated checksum.
Build system: x86_64
Build-tested: ipq806x/R7800
Signed-off-by: John Audia <therealgraysky@proton.me>
Changes:
9c44557 opkg_remove: avoid remove pkg repeatly with option --force-removal-of-dependent-packages
2edcfad libopkg: set 'const' attribute for argv
This should fix the CI error in the packages repository, which happens with perl.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Mostly backports by a Red Hat employee as 0.62 and newer demands Python
3.7+. Same reason 0.61 is kept here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
9eabf30 Release version 5.18.
2b3ddcb ethtool: fec: Change the prompt string to adapt to current situations
d660dde pretty: add missing message descriptions for rings
aaeb16a pretty: support u8 enumerated types
6b320b8 rings: add support to set/get cqe size
41fddc0 update UAPI header copies
42e6c28 help: fix alignment of rx-buf-len parameter
e1d0a19 ethtool.8: Fix typo in man page
37f0586 Release version 5.17.
8c2984c strset: do not put a pointer to a local variable to nlctx
8fd02a2 ioctl: add the memory free operation after send_ioctl call fails
b9f25ea ethtool: Add support for OSFP transceiver modules
6e79542 features: add --json support
5ed5ce5 Merge branch 'next' into master
b90abbb man: document recently added parameters
51a9312 tunables: add support to get/set tx copybreak buf size
a081c2a rings: add support to set/get rx buf len
d699bab Merge branch 'master' into next
52db6b9 Merge branch 'review/module-extstate' into next
6407b52 monitor: add option for --show-module/--set-module
1f35786 ethtool: Add transceiver module extended state
2d4c5b7 ethtool: Add ability to control transceiver modules' power mode
005908b Update UAPI header copies
Signed-off-by: Nick Hainke <vincent@systemli.org>
WolfSSL is crashing with an illegal opcode in some x86_64 CPUs that have
AES instructions but lack other extensions that are used by WolfSSL
when AES-NI is enabled.
Disable the option by default for now until the issue is properly fixed.
People can enable them in a custom build if they are sure it will work
for them.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Setting up DSA bond silently fails if mode is not 802.3ad. Add log message
to fix it. As we are already here harmonize all logging messages in the
add/delete functions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
This reverts the airtime scheduler back from the virtual-time based scheduler
to the deficit round robin scheduler implementation.
This reduces burstiness and improves fairness by improving interaction with AQL.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The SFP cages 9F and 10F share the same SCL line. Currently, there
isn't a good way to model this. Thus, only one SFP port can be fully
supported.
Cage 10F is fully supported with an I2C bus and sfp handle. Linux
automatically handles enabling or disabling the TX laser.
Cage 9F is only parially supported, without the sfp handle. The SDA
line is hogged as an input, so that it remains high. SCL transitions
sould not affect modules connected to this cage. The default value of
the tx-disable line is high (active). It is exported as a gpio, but
the laser is off by default. To enable the laser:
echo 0 > /sys/class/gpio/sff-p9-tx-disable/value
Thus, both modules can be used for networking, but only 10F will be
able to detect and identify a plugged in SFP module.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
