Add support for the TP-Link SG2008P switch. This is an RTL8380 based
switch with 802.3af one the first four ports.
Specifications:
---------------
* SoC: Realtek RTL8380M
* Flash: 32 MiB SPI flash (Vendor varies)
* RAM: 256 MiB (Vendor varies)
* Ethernet: 8x 10/100/1000 Mbps with PoE on 4 ports
* Buttons: 1x "Reset" button on front panel
* Power: 53.5V DC barrel jack
* UART: 1x serial header, unpopulated
* PoE: 1x TI TPS23861 I2C PoE controller
Works:
------
- (8) RJ-45 ethernet ports
- Switch functions
- System LED
Not yet enabled:
----------------
- Power-over-Ethernet (driver works, but doesn't enable "auto" mode)
- PoE, Link/Act, PoE max and System LEDs
Install via web interface:
-------------------------
Not supported at this time.
Install via serial console/tftp:
--------------------------------
The footprints R27 (0201) and R28 (0402) are not populated. To enable
serial console, 50 ohm resistors should be soldered -- any value from
0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge.
The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.
Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. The sysupgrade image can also be flashed. To install OpenWRT:
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
Power on device, and stop boot by pressing any key.
Once the shell is active:
1. Ground out the CLK (pin 16) of the ROM (U7)
2. Select option "3. Start"
3. Bootloader notes that "The kernel has been damaged!"
4. Release CLK as sson as bootloader thinks image is corrupted.
5. Bootloader enters automatic recovery -- details printed on console
6. Watch as the bootloader flashes and boots OpenWRT.
Blind install via tftp:
-----------------------
This method works when it's not feasible to install a serial header.
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
3. Watch network traffic (tcpdump or wireshark works)
4. Power on the device.
5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U7)
6. When 192.168.0.30 makes tftp requests, release pin 16
7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support for HPE 1920 images depends on two non-existent tools (mkh3cimg
and mkh3cvfs) from the in the firmware-utils package. Revert commit
f2f09bc002 ("realtek: add support for HPE 1920 series") until support
for these tools is merged and made available in OpenWrt.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Hardware information:
---------------------
- HPE 1920-8G:
- RTL8380 SoC
- 8 Gigabit RJ45 ports (built-in RTL8218B)
- 2 SFP ports (built-in SerDes)
- HPE 1920-16G / HPE 1920-24G (same board):
- RTL8382 SoC
- 16/24 Gigabit RJ45 ports (built-in RTL8218B, 1/2 external RTL8218D)
- 4 SFP ports (external RTL8214FC)
- Common:
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Remove redundant target-level entries, noting that these settings will be
configured from "Kernel build options" of Kconfig.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[remove from new configs introduced after patch submission]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The system status LED on Panasonic Switch-M8eG PN28080K is connected to
a PCA9539PW. To use the LED as a status LED of OpenWrt while booting,
enable the pca953x driver and built-in to the kernel.
Also enable CONFIG_GPIO_PCA953X_IRQ to use interrupt via RTL83xx GPIO.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Sander Vanheule <sander@svanheule.net>
Selects the new CEVT timer for Realtek instead of the previous
timer driver. While we are at it, we explicitily state we do
not use the I2C driver of the RTL9300.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Set CONFIG_FORCE_MAX_ZONEORDER setting to 13 to allow larger
contiguous memory allocation for the DMA of the Ethernet
driver. Increase the number of entries in the RX ring
to 300 making use of the larger DMA region now possible for
receiveing packets.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
The RTL838X SoCs do not use Aquantia PHYs, remove this.
Also the RTL838X uses a high resolution R4K timer.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Creates RTL83XX as a basic kernel config parameter for the
RTL838X, RTL839x, RTL930X and RTL931X platforms with respective
configurations for the SoCs, which are introduced in addition.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
mv generic/target.mk to rtl838x/target.mk in order to create
an initial makefile for the rtl838x sub-architecture
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
