ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-23 15:32:33 +00:00
Code Issues Actions 7 Packages Projects Releases Wiki Activity

realtek: add support for HPE 1920 series

Browse Source 
Hardware information:
---------------------

- HPE 1920-8G:
  - RTL8380 SoC
  - 8 Gigabit RJ45 ports (built-in RTL8218B)
  - 2 SFP ports (built-in SerDes)

- HPE 1920-16G / HPE 1920-24G (same board):
  - RTL8382 SoC
  - 16/24 Gigabit RJ45 ports (built-in RTL8218B, 1/2 external RTL8218D)
  - 4 SFP ports (external RTL8214FC)

- Common:
  - RJ45 RS232 port on front panel
  - 32 MiB NOR Flash
  - 128 MiB DDR3 DRAM
  - PT7A7514 watchdog

Booting initramfs image:
------------------------

- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
  connect the server to a switch port.

- Connect to the console port of the device and enter the extended
  boot menu by typing Ctrl+B when prompted.

- Choose the menu option "<3> Enter Ethernet SubMenu".

- Set network parameters via the option "<5> Modify Ethernet Parameter".
  Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
  can be left blank, it is not required for booting from RAM). Note that
  the configuration is saved on flash, so it only needs to be done once.

- Select "<1> Download Application Program To SDRAM And Run".

Initial installation:
---------------------

- Boot an initramfs image as described above, then use sysupgrade to
  install OpenWrt permanently. After initial installation, the
  bootloader needs to be configured to load the correct image file

- Enter the extended boot menu again and choose "<4> File Control",
  then select "<2> Set Application File type".

- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
  use the option "<1> +Main" to select it as boot image.

- Choose "<0> Exit To Main Menu" and then "<1> Boot System".

NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This commit is contained in:
Jan Hoffmann 2022-07-23 22:53:19 +02:00 committed by Daniel Golle
parent 5fcc6f0f19
commit f2f09bc002
10 changed files with 540 additions and 3 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

18
target/linux/realtek/base-files/etc/board.d/02_network
View File

@ -22,9 +22,20 @@ ucidef_set_bridge_device switch
ucidef_set_interface_lan "$lan_list"
lan_mac=""
lan_mac_start=""
lan_mac_end=""
label_mac=""
case $board in
hpe,1920-8g|\
hpe,1920-16g|\
hpe,1920-24g)
label_mac=$(mtd_get_mac_binary factory 0x68)
lan_mac=$label_mac
mac_count1=$(hexdump -v -n 4 -s 0x110 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null)
mac_count2=$(hexdump -v -n 4 -s 0x114 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null)
lan_mac_start=$(macaddr_add $lan_mac 2)
lan_mac_end=$(macaddr_add $lan_mac $((mac_count2-mac_count1)))
;;
*)
lan_mac=$(mtd_get_mac_ascii u-boot-env2 mac_start)
lan_mac_end=$(mtd_get_mac_ascii u-boot-env2 mac_end)
@ -36,10 +47,11 @@ esac
ucidef_set_interface_macaddr "lan" $lan_mac
ucidef_set_bridge_mac "$lan_mac"
ucidef_set_network_device_mac eth0 $lan_mac
[ -z "$lan_mac_start" ] && lan_mac_start=$lan_mac
for lan in $lan_list; do
ucidef_set_network_device_mac $lan $lan_mac
[ -z "$lan_mac_end" ] || [ "$lan_mac" == "$lan_mac_end" ] && lan_mac=$(macaddr_setbit_la $lan_mac)
lan_mac=$(macaddr_add $lan_mac 1)
ucidef_set_network_device_mac $lan $lan_mac_start
[ -z "$lan_mac_end" ] || [ "$lan_mac_start" == "$lan_mac_end" ] && lan_mac_start=$(macaddr_setbit_la $lan_mac_start)
lan_mac_start=$(macaddr_add $lan_mac_start 1)
done
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac

113
target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts Normal file
View File

@ -0,0 +1,113 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "rtl838x.dtsi"
#include "rtl838x_hpe_1920.dtsi"
/ {
compatible = "hpe,1920-8g", "realtek,rtl838x-soc";
model = "HPE 1920-8G (JG920A)";
gpio1: rtl8231-gpio {
compatible = "realtek,rtl8231-gpio";
#gpio-cells = <2>;
gpio-controller;
indirect-access-bus-id = <0>;
};
i2c0: i2c-gpio-0 {
compatible = "i2c-gpio";
sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
};
sfp0: sfp-0 {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
// tx-fault and tx-disable unconnected
};
i2c1: i2c-gpio-1 {
compatible = "i2c-gpio";
sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
};
sfp1: sfp-1 {
compatible = "sff,sfp";
i2c-bus = <&i2c1>;
los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
// tx-fault and tx-disable unconnected
};
};
&ethernet0 {
mdio: mdio-bus {
compatible = "realtek,rtl838x-mdio";
regmap = <&ethernet0>;
#address-cells = <1>;
#size-cells = <0>;
INTERNAL_PHY(8)
INTERNAL_PHY(9)
INTERNAL_PHY(10)
INTERNAL_PHY(11)
INTERNAL_PHY(12)
INTERNAL_PHY(13)
INTERNAL_PHY(14)
INTERNAL_PHY(15)
INTERNAL_PHY(24)
INTERNAL_PHY(26)
};
};
&switch0 {
ports {
#address-cells = <1>;
#size-cells = <0>;
SWITCH_PORT(8, 1, internal)
SWITCH_PORT(9, 2, internal)
SWITCH_PORT(10, 3, internal)
SWITCH_PORT(11, 4, internal)
SWITCH_PORT(12, 5, internal)
SWITCH_PORT(13, 6, internal)
SWITCH_PORT(14, 7, internal)
SWITCH_PORT(15, 8, internal)
port@24 {
reg = <24>;
label = "lan9";
phy-mode = "1000base-x";
managed = "in-band-status";
sfp = <&sfp0>;
};
port@26 {
reg = <26>;
label = "lan10";
phy-mode = "1000base-x";
managed = "in-band-status";
sfp = <&sfp1>;
};
port@28 {
ethernet = <&ethernet0>;
reg = <28>;
phy-mode = "internal";
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};

48
target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts Normal file
View File

@ -0,0 +1,48 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "rtl8382_hpe_1920.dtsi"
/ {
compatible = "hpe,1920-16g", "realtek,rtl838x-soc";
model = "HPE 1920-16G (JG923A)";
};
&switch0 {
ports {
#address-cells = <1>;
#size-cells = <0>;
SWITCH_PORT(8, 1, internal)
SWITCH_PORT(9, 2, internal)
SWITCH_PORT(10, 3, internal)
SWITCH_PORT(11, 4, internal)
SWITCH_PORT(12, 5, internal)
SWITCH_PORT(13, 6, internal)
SWITCH_PORT(14, 7, internal)
SWITCH_PORT(15, 8, internal)
SWITCH_PORT(16, 9, qsgmii)
SWITCH_PORT(17, 10, qsgmii)
SWITCH_PORT(18, 11, qsgmii)
SWITCH_PORT(19, 12, qsgmii)
SWITCH_PORT(20, 13, qsgmii)
SWITCH_PORT(21, 14, qsgmii)
SWITCH_PORT(22, 15, qsgmii)
SWITCH_PORT(23, 16, qsgmii)
SWITCH_PORT(24, 17, qsgmii)
SWITCH_PORT(25, 18, qsgmii)
SWITCH_PORT(26, 19, qsgmii)
SWITCH_PORT(27, 20, qsgmii)
port@28 {
ethernet = <&ethernet0>;
reg = <28>;
phy-mode = "internal";
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};

68
target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts Normal file
View File

@ -0,0 +1,68 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "rtl8382_hpe_1920.dtsi"
/ {
compatible = "hpe,1920-24g", "realtek,rtl838x-soc";
model = "HPE 1920-24G (JG924A)";
};
&mdio {
EXTERNAL_PHY(0)
EXTERNAL_PHY(1)
EXTERNAL_PHY(2)
EXTERNAL_PHY(3)
EXTERNAL_PHY(4)
EXTERNAL_PHY(5)
EXTERNAL_PHY(6)
EXTERNAL_PHY(7)
};
&switch0 {
ports {
#address-cells = <1>;
#size-cells = <0>;
SWITCH_PORT(0, 1, qsgmii)
SWITCH_PORT(1, 2, qsgmii)
SWITCH_PORT(2, 3, qsgmii)
SWITCH_PORT(3, 4, qsgmii)
SWITCH_PORT(4, 5, qsgmii)
SWITCH_PORT(5, 6, qsgmii)
SWITCH_PORT(6, 7, qsgmii)
SWITCH_PORT(7, 8, qsgmii)
SWITCH_PORT(8, 9, internal)
SWITCH_PORT(9, 10, internal)
SWITCH_PORT(10, 11, internal)
SWITCH_PORT(11, 12, internal)
SWITCH_PORT(12, 13, internal)
SWITCH_PORT(13, 14, internal)
SWITCH_PORT(14, 15, internal)
SWITCH_PORT(15, 16, internal)
SWITCH_PORT(16, 17, qsgmii)
SWITCH_PORT(17, 18, qsgmii)
SWITCH_PORT(18, 19, qsgmii)
SWITCH_PORT(19, 20, qsgmii)
SWITCH_PORT(20, 21, qsgmii)
SWITCH_PORT(21, 22, qsgmii)
SWITCH_PORT(22, 23, qsgmii)
SWITCH_PORT(23, 24, qsgmii)
SWITCH_PORT(24, 25, qsgmii)
SWITCH_PORT(25, 26, qsgmii)
SWITCH_PORT(26, 27, qsgmii)
SWITCH_PORT(27, 28, qsgmii)
port@28 {
ethernet = <&ethernet0>;
reg = <28>;
phy-mode = "internal";
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};

117
target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi Normal file
View File

@ -0,0 +1,117 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "rtl838x.dtsi"
#include "rtl838x_hpe_1920.dtsi"
/ {
gpio1: rtl8231-gpio {
compatible = "realtek,rtl8231-gpio";
#gpio-cells = <2>;
gpio-controller;
indirect-access-bus-id = <0>;
};
i2c0: i2c-gpio-0 {
compatible = "i2c-gpio";
sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
};
sfp0: sfp-0 {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
// tx-fault unconnected
// tx-disable connected to RTL8214FC
};
i2c1: i2c-gpio-1 {
compatible = "i2c-gpio";
sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
};
sfp1: sfp-1 {
compatible = "sff,sfp";
i2c-bus = <&i2c1>;
los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
// tx-fault unconnected
// tx-disable connected to RTL8214FC
};
i2c2: i2c-gpio-2 {
compatible = "i2c-gpio";
sda-gpios = <&gpio1 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
};
sfp2: sfp-2 {
compatible = "sff,sfp";
i2c-bus = <&i2c2>;
los-gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
// tx-fault unconnected
// tx-disable connected to RTL8214FC
};
i2c3: i2c-gpio-3 {
compatible = "i2c-gpio";
sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio1 32 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
};
sfp3: sfp-3 {
compatible = "sff,sfp";
i2c-bus = <&i2c3>;
los-gpio = <&gpio1 34 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpio1 33 GPIO_ACTIVE_LOW>;
// tx-fault unconnected
// tx-disable connected to RTL8214FC
};
};
&ethernet0 {
mdio: mdio-bus {
compatible = "realtek,rtl838x-mdio";
regmap = <&ethernet0>;
#address-cells = <1>;
#size-cells = <0>;
INTERNAL_PHY(8)
INTERNAL_PHY(9)
INTERNAL_PHY(10)
INTERNAL_PHY(11)
INTERNAL_PHY(12)
INTERNAL_PHY(13)
INTERNAL_PHY(14)
INTERNAL_PHY(15)
EXTERNAL_PHY(16)
EXTERNAL_PHY(17)
EXTERNAL_PHY(18)
EXTERNAL_PHY(19)
EXTERNAL_PHY(20)
EXTERNAL_PHY(21)
EXTERNAL_PHY(22)
EXTERNAL_PHY(23)
EXTERNAL_SFP_PHY_FULL(24, 0)
EXTERNAL_SFP_PHY_FULL(25, 1)
EXTERNAL_SFP_PHY_FULL(26, 2)
EXTERNAL_SFP_PHY_FULL(27, 3)
};
};

7
target/linux/realtek/dts-5.10/rtl838x.dtsi
View File

@ -27,6 +27,13 @@
reg = <##n>; \
};
#define EXTERNAL_SFP_PHY_FULL(n, s) \
phy##n: ethernet-phy@##n { \
compatible = "ethernet-phy-ieee802.3-c22"; \
sfp = <&sfp##s>; \
reg = <##n>; \
};
#define SWITCH_PORT(n, s, m) \
port@##n { \
reg = <##n>; \

96
target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi Normal file
View File

@ -0,0 +1,96 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
/ {
chosen {
bootargs = "console=ttyS0,38400";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x8000000>;
};
watchdog1: watchdog {
// PT7A7514
compatible = "linux,wdt-gpio";
gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
hw_algo = "toggle";
hw_margin_ms = <1000>;
always-running;
pinctrl-names = "default";
pinctrl-0 = <&pinmux_disable_sys_led>;
};
};
&watchdog0 {
status = "disabled";
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
m25p,fast-read;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "bootware_basic";
reg = <0x0 0x50000>;
read-only;
};
partition@0x60000 {
label = "bootware_data";
reg = <0x60000 0x30000>;
read-only;
};
partition@0x90000 {
label = "bootware_extend";
reg = <0x90000 0x40000>;
read-only;
};
partition@0x100000 {
label = "bootware_basic_backup";
reg = <0x100000 0x50000>;
read-only;
};
partition@0x160000 {
label = "bootware_data_backup";
reg = <0x160000 0x30000>;
read-only;
};
partition@0x190000 {
label = "bootware_extend_backup";
reg = <0x190000 0x40000>;
read-only;
};
partition@0x300000 {
label = "firmware";
compatible = "h3c,vfs-firmware";
reg = <0x300000 0x1cf0000>;
};
partition@0x1ff0000 {
label = "factory";
reg = <0x1ff0000 0x10000>;
read-only;
};
};
};
};

49
target/linux/realtek/image/Makefile
View File

@ -8,6 +8,7 @@ KERNEL_ENTRY = 0x80000400
DEVICE_VARS += ZYXEL_VERS DLINK_KERNEL_PART_SIZE
DEVICE_VARS += CAMEO_KERNEL_PART CAMEO_ROOTFS_PART CAMEO_CUSTOMER_SIGNATURE CAMEO_BOARD_VERSION
DEVICE_VARS += H3C_PRODUCT_ID H3C_DEVICE_ID
define Build/zyxel-vers
( echo VERS;\
@ -41,6 +42,43 @@ define Build/dlink-headers
cat $@.kernel_part.hex $@.rootfs_part.hex > $@
endef
define Build/7z
$(STAGING_DIR_HOST)/bin/7zr a $(@).new -t7z -m0=lzma $(@)
mv $@.new $@
endef
define Build/h3c-image
$(STAGING_DIR_HOST)/bin/mkh3cimg \
-i $(@) \
-o $(@).new \
-c 7z \
-p $(H3C_PRODUCT_ID) \
-d $(H3C_DEVICE_ID)
mv $@.new $@
endef
define Build/h3c-vfs
$(STAGING_DIR_HOST)/bin/mkh3cvfs \
-i $(@) \
-o $(@).new \
-f openwrt-kernel.bin
mv $@.new $@
endef
define Build/relocate-kernel
rm -rf $@.relocate
$(CP) ../../generic/image/relocate $@.relocate
$(MAKE) -j1 -C $@.relocate KERNEL_ADDR=$(KERNEL_LOADADDR) LZMA_TEXT_START=0x82000000 \
CROSS_COMPILE=$(TARGET_CROSS)
( \
dd if=$@.relocate/loader.bin bs=32 conv=sync && \
perl -e '@s = stat("$@"); print pack("N", @s[7])' && \
cat "$@" \
) > "$@.new"
mv "$@.new" "$@"
rm -rf $@.relocate
endef
define Device/Default
PROFILES = Default
KERNEL := kernel-bin | append-dtb | gzip | uImage gzip
@ -52,6 +90,17 @@ define Device/Default
check-size | append-metadata
endef
define Device/hpe_1920
DEVICE_VENDOR := HPE
IMAGE_SIZE := 29632k
BLOCKSIZE := 64k
H3C_PRODUCT_ID := 0x3c010501
KERNEL := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image | h3c-vfs
KERNEL_INITRAMFS := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs | check-size | append-metadata
endef
# "NGE" refers to the uImage magic
define Device/netgear_nge
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma

24
target/linux/realtek/image/rtl838x.mk
View File

@ -65,6 +65,30 @@ define Device/engenius_ews2910p
endef
TARGET_DEVICES += engenius_ews2910p
define Device/hpe_1920-8g
$(Device/hpe_1920)
SOC := rtl8380
DEVICE_MODEL := 1920-8G (JG920A)
H3C_DEVICE_ID := 0x00010023
endef
TARGET_DEVICES += hpe_1920-8g
define Device/hpe_1920-16g
$(Device/hpe_1920)
SOC := rtl8382
DEVICE_MODEL := 1920-16G (JG923A)
H3C_DEVICE_ID := 0x00010026
endef
TARGET_DEVICES += hpe_1920-16g
define Device/hpe_1920-24g
$(Device/hpe_1920)
SOC := rtl8382
DEVICE_MODEL := 1920-24G (JG924A)
H3C_DEVICE_ID := 0x00010027
endef
TARGET_DEVICES += hpe_1920-24g
define Device/inaba_aml2-17gp
SOC := rtl8382
IMAGE_SIZE := 13504k

3
target/linux/realtek/rtl838x/config-5.10
View File

@ -74,6 +74,8 @@ CONFIG_GPIO_PCA953X=y
CONFIG_GPIO_PCA953X_IRQ=y
CONFIG_GPIO_REALTEK_OTTO=y
CONFIG_GPIO_RTL8231=y
CONFIG_GPIO_WATCHDOG=y
# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set
CONFIG_GRO_CELLS=y
CONFIG_HANDLE_DOMAIN_IRQ=y
CONFIG_HARDWARE_WATCHPOINTS=y
@ -134,6 +136,7 @@ CONFIG_MTD_SPI_NOR=y
CONFIG_MTD_SPLIT_BRNIMAGE_FW=y
CONFIG_MTD_SPLIT_EVA_FW=y
CONFIG_MTD_SPLIT_FIRMWARE=y
CONFIG_MTD_SPLIT_H3C_VFS=y
CONFIG_MTD_SPLIT_TPLINK_FW=y
CONFIG_MTD_SPLIT_UIMAGE_FW=y
CONFIG_NEED_DMA_MAP_STATE=y