Changes from 5.4 to 5.10:
-------------------------
- patches from 5.4 are all upstream for 5.10 execpt for
0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch
- disable block device data integrity (DIF/DIX/T10) in default config
(CONFIG_BLK_DEV_INTEGRITY)
This feature is only supported by:
- Enterprise SAS/SCSI HBAs and Disks
- Software raid
- NVMEs with metadata capabilities (most don't have this)
None of which are part of any octeontx boards.
- arm64 TEXT_OFFSET (0x80000) has been removed after 5.4
This will break Uimages with kernel load addresses that aren't 2MiB
aligned any longer. Resulting in the kernel silently fail to boot.
For Gatworks newport boards for example, the uimage kernel load
and execute address is 0x20080000. These need to be changed to
0x20000000 when running kernels beyond 5.4.
Tested-on: Gateworks Newport GW64xx
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Linksyses Audi EA3500 and Viper E4200/E4500 have too small kernel
partition size when kernel 5.10 is used. This patch change kernel
partition to maximum size allowed by u-boot.
Kernel size is overlapping rootfs now, like mvebu Linksyses and stock
partition table. It fix back to stock via sysupgrade, which was broken
since 18.06.
Fixes: 9808b9ae02 ("kirkwood: switch to kernel 4.9")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HPv2
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: W631GG8MB-12 128 MiB DDR3 SDRAM
(stock firmware is configured to use only 64 MiB)
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
24 ethernet port PoE status LEDs
2 SFP status/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESTORE" button on front panel
1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J41) with populated standard pin connector on
the left edge of the PCB, angled towards the side.
The casing has a rectangular cutout on the side that provides
external access to these pins.
Pinout (front to back):
+ GND
+ TX
+ RX
+ VCC
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
OEM upgrade method:
(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
like commit 78c1ed6. Without this,Some USB port on H3 baseboard
can' work. So, need enable MUSB support on this target.
Signed-off-by: Zhao Yu <574249312@qq.com>
This patch fixes the forwarding behavior of bridge in bridge
configurations with DSA.
Without it, the configuration of the upper bridge might overwrite
settings of the lower bridge. For example, a vlan-aware bridge
with DSA interfaces in it might be offloaded to the DSA hardware. If the
bridge interface itself gets slave of a different bridge without vlan
filtering, the vlan filtering setting of the lower bridge is overwritten
by the upper bridge, which results in an incorrect hardware
configuration.
This was backported from kernel 5.7.
Ref: https://lore.kernel.org/netdev/20191222192235.GK25745@shell.armlinux.org.uk/
Fixes: FS#3996
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Designated initializers are required when using the randstruct GCC
plugin, otherwise an error like the following is seen:
./include/linux/lzma.h:60:31: error: positional initialization of field in 'struct' declared with 'designated_init' attribute [-Werror=designated-init]
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
These options are selectable when some of the kernel debug options like
KERNEL_SOFTLOCKUP_DETECTOR are selected.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The LOCKUP_DETECTOR configuration option split into the
SOFTLOCKUP_DETECTOR and HARDLOCKUP_DETECTOR configuration option some
time ago. The HARDLOCKUP_DETECTOR option is only working on some
architectures, but SOFTLOCKUP_DETECTOR should work everywhere. Replace
KERNEL_LOCKUP_DETECTOR with KERNEL_SOFTLOCKUP_DETECTOR.
LOCKUP_DETECTOR will be selected by SOFTLOCKUP_DETECTOR automatically.
Fixes: b951f53fba ("build: Add additional kernel debug options")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move kernel version to 5.10 as has been tested by many users
with positive feedback.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[Tested on: ipq8064/g10; ipq8065/nbg6817]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The ipq-wifi-netgear_wac510 package is not selected by any device and would
be empty anyway. The default board-2.bin from ath10k-board-qca4019 is
therefore used for this device and the package doesn't provide any visible
features.
Fixes: b126d9c3a3 ("ipq40xx: add netgear wac510 support")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the Plasma Cloud PA2200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.
Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the Plasma Cloud PA1200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.
Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the EnGenius EMR3500 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.
Fixes: 3f61e5e1b9 ("ipq40xx: add support for EnGenius EMR3500")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the EnGenius EMD1 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.
Fixes: 51f3035978 ("ipq40xx: add support for EnGenius EMD1")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The structured soft-version partition has a field which contains a
(source) revision number. Factory images used to include this, but
it was accidentaly removed during an earlier refactoring.
Include the source revision number again in the generated soft-version
partition. Additionaly, also show this revision number when printing
image info.
Fixes: 1a211af2cb ("firmware-utils: tplink-safeloader: refactor meta-partition generation")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
1. Add support for Marvell CN9130 SoC
2. Add support for CP115,and create an armada-cp11x.dtsi file which will be used to instantiate both CP110 and CP115
3. Add support for AP807/AP807-quad,AP807 is a major component of CN9130 SoC series
4. Drop PCIe I/O ranges from CP11x file and externalize PCIe macros from CP11x file
Signed-off-by: Ian Chang <ianchang@ieiworld.com>
When doing parallel build on a fast machine with bottleneck in i/o,
m_xt.so may start linking faster than dynsyms.list gets populated,
resulting in error:
ld:dynsyms.list:0: syntax error in dynamic list
Fix this by adding dynsyms.list as make dependency to m_xt.so
Described also here:
https://bugs.openwrt.org/index.php?do=details&task_id=3353
Change from v1:
- add dynsysms.list dependancy only when shared libs are enabled
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Fixes: FS#3353
The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60
seconds to 21 seconds in 2012 in the upstream kernel. Some targets
already use 21 seconds.
This patch changes the default value in the generic configuration to 21
seconds and removes the target specific configuration options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
It's been brewing on my cortexa9 subtarget (Turris Omnia) for months.
Perfectly stable.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
[modify subject to match previous updates]
Signed-off-by: Paul Spooren <mail@aparcar.org>
This was missed because scancode license scanner was confused by a
slightly different than expected license text (96,75% license score).
License text included "file" instead of "library" in the main part of
the licensing info. It also used "The GNU C Library" instead of the
standard "This library" in 2nd and 3rd paragraphs.
The first paragraph clearly mentions LGPL-2.1-or-later and the use of
"file" instead of "library" should not affect licensing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device is a wireless access point working on the 2.4 GHz and 5 GHz
band, based on Qualcomm/Atheros QCA9563 + QCA9886.
Specification
- 775 MHz CPU
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- QCA9563: 2.4 GHz 3x3
- QCA9886: 5 GHz
- AR8033: 1x 1 Gbs Ethernet
- 4x LED, WPS factory reset and power button
- bare UART on PCB (accessible through testpoints)
Methods for Flashing:
- Apply factory image in OEM firmware web-gui. Wait a minute after the
progress bar completes and restart the device.
- Sysupgrade on top of existing OpenWRT image
- Solder wires onto UART testpoints and attach a terminal.
Boot the device and press enter to enter u-boot's menu. Then issue the
following commands
1. setenv serverip your-server-ip
setenv ipaddr your-device-ip
2. tftp 0x80060000 openwrt-squashfs.bin (Rembember output of size in
hex, henceforth "sizeinhex")
3. erase 0x9f030000 +"sizeinhex"
4. cp.b 0x80060000 0x9f030000 0x"sizeinhex"
5. reboot
Recover:
- U-boot serial console
Signed-off-by: Robert Balas <balasr@iis.ee.ethz.ch>
[convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update busybox to version 1.34.0
* Remove upstreamed patches (205, 530, 540)
* Remove one old patch that does not apply any more. (203)
That was originally introduced in 2008 with 563d23459,
but does not apply after busybox restructuring with
https://git.busybox.net/busybox/commit/networking/udhcp/dhcpc.c?h=1_34_stable&id=e6007c4911c3ea26925f9473b9f156a692585f30
and
https://git.busybox.net/busybox/commit/networking/udhcp/dhcpc.c?h=1_34_stable&id=1c7253726fcbab09917f143f0b703efbd2df55c3
* Refresh config and patches.
* Backport upstream fixes for
- MIPS compilation breakage and
- process substitution regression
Config refresh:
Refresh commands, run after busybox is first built once:
cd utils/busybox/
cd config/
../convert_menuconfig.pl ../../../../build_dir/target-aarch64_cortex-a53_musl/busybox-default/busybox-1.34.0
cd ..
./convert_defaults.pl < ../../../build_dir/target-aarch64_cortex-a53_musl/busybox-default/busybox-1.34.0/.config > Config-defaults.in
Manual edits needed afterward:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt configTARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
BUSYBOX_DEFAULT_UDHCPC_DEFAULT_INTERFACE (just "")
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in : change at "Options common to all shells" the symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Specifications:
- SoC: MT7622
- RAM: 512MB
- Flash: MX35LF1GE4AB 128MB SPI NAND
- Ethernet: RTL8367S 5x1GbE
- WiFi: 2.4G: MT7622 5G: MT7615N x2
- Other ports: USB3.0 x1
Flash instruction:
*important*: upgrade vendor firmware to at least V7.1cu.643_B20200521
1. hold the reset button and power on the device. wait for about 10s
before releasing the reset button.
2. upload sysupgrade.bin via u-boot recovery page on http://192.168.1.1
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
929c862 vm: fix toplevel function call protocol
8f34d70 fs: fix chown() and rename() error return values
03ca445 tests: disable fuzz tests for now
3b1be3d types: mark further GC roots
d49af4e types: fix comparison of differently signed integers
c79ff39 types: handle conversion errors when dealing with negative error indexes
3315b1f types: allow negative array indexes
d5b25f9 treewide: harmonize function naming
cc4ce8d module: remove unused defines
f5d7526 examples: add libucode usage examples
559eff2 types, vm: adjust GC api
e5e7e62 treewide: move header files into dedicated directory
ff6168a build: install header files
7e6ce0f main: introduce new flag `-x` to allow disabling specific functions
b1817b3 vm: fix invalid memory access on GC'ing uninitialized VM context
498fe87 main: refactor option parsing and VM setup
ff52440 treewide: consolidate typedef naming
1d60418 vm: add API to control trace mode
48f33ad vm: make root exception handler configurable
0f69f09 vm: fix invalid memory access on toplevel function calls
6bcc318 vm: fix handling exceptions in top-level function calls
4ae0568 lib, vm: reimplement exit() as exception type
2f77657 vm: extend API to allow returning result value from VM execution
111645a vm: remove module preloading logic
38ff6de main: preload modules ourselves
d5bc223 vm: add uc_vm_invoke() helper
ef0baf1 vm: cosmetic fix for outputting exceptions without source context
b11a2fa vm: move global scope allocation into uc_vm_init()
900b2a3 vm: add getter and setter for vm globals scope
0179576 lib: rename uc_add_proto_functions() to uc_add_functions()
98b9c84 lib: expose stdlib function array
1adfba0 treewide: eliminate dead code and unused functions
3974e71 treewide: replace a number of unnecessary type casts
bf85226 treewide: move ressource type registry into vm instance
e2b3d2e build: split into libucode and ucode cli
dad8f3a types: properly deal with circular data in GC mark phase
62dbd64 lexer: rename UT_ prefixed constants to UC_
bc8e465 types: fix wrong assert() on tearing down object trees
853b9f1 vm: fix potential invalid memory access in uc_vm_get_error_context()
6f05cdd lib: fix refcount imbalance in uc_require_path()
96f140b lib, vm: ensure that require() compiles modules only once
df5db5f compiler: don't segfault on invalid declaration expressions
a97c7a1 lexer: transition into EOF state on unrecognized character
2a838d1 compiler: improve mapping of binary operator tokens to instructions
9872f65 vm: add support for I_LE and I_GE instructions
4e410c3 treewide: let uc_cmp() use instruction instead of token numbers
ce6081d lexer, vm: reorder token and instruction numbers
234a4f6 lib: implement b64enc() and b64dec() functions
856a0c0 lib: only consider context of calling function for callbacks
86fb130 lib: implement min() and max() functions
3e893e6 lib: pass-through "this" context to library function callbacks
42de7ab lib: implement `sourcepath()` function
05c80a7 lib: fix negative uc_index() return value on 32bit systems
9874562 lexer: implement raw code mode
3b665c8 lexer: drop value union from keyword table
44354cf lexer, compiler: separate TK_BOOL token into TK_TRUE and TK_FALSE tokens
5879bdf syntax: drop Infinity and NaN keywords
d4edadc lib: rename uc_lib_init() to uc_load_stdlib()
d81bad7 main, lib: move allocation of globals object into lib function
c4f4b38 main: simplify REQUIRE_SEARCH_PATH initialization
54ca3aa types: fix uninitialized memory on setting non-contiguous array indexes
cbc0d78 build: let require search patch default to CMAKE_INSTALL_PREFIX
5714705 syntax: introduce `const` support
ed32c42 compiler, lexer: add NO_LEGACY define to disable legacy syntax features
ff6811f syntax: implement `delete` as proper operator
5803d86 lib: implement wildcard() function
dfb7379 fs: implement chmod(), chown(), rename() and glob() functions
1ddf5b6 lexer: skip interpreter line in any source buffer
9951a00 build: lower minimum required CMake version to v3.13
7b81ab2 main: expose argv as global ARGV array to ucode scripts
7283a70 tests: rename misnamed testcases for consistency
3f80116 compiler: fix local for-loop initializer variable declarations
f20b56f compiler: properly parse slashes in parenthesized division expressions
5c4e1ea lib: implement regexp(), a function to construct regexp instances at runtime
e546bba lib: implement render(), an include variant capturing output in a string
0cb10c6 vm: implement mechanism to change output file descriptor
eb8a64d lib: fix uc_sort()
f1ffc9f vm: truncate long values after 60 chars in trace output
850612f compiler: properly handle break/continue in nested scopes
f0a9875 compiler: properly handle keyword in parenthesized property access expression
1660433 compiler: fix stack mismatch on compiling `use strict` statements
a36e0df syntax: implement support for 'use strict' pragma
827a34a vm, compiler: get rid of unused struct members
594cdf3 lib: implement assert()
c4d1648 lib: add support for pretty printing JSON to printf() and sprintf()
f2eaea3 lib: gracefully handle truncated format strings in uc_printf_common()
02629b8 lexer: fix infinite loop on parsing unterminated comments
2bc9bac lexer: fix infinite loop on parsing unterminated expression blocks
f73e201 lexer: fix infinite loop when parsing regexp literal at EOF
86b4863 compiler: fix segfault on parsing invalid pre/post increment expressions
0e24509 lib: fix reporting source context lines at EOF
e66b2ad compiler, lexer: improve lexical state handling
e29b574 lib: fix uc_split() quirks
64eec7f treewide: ISO C / pedantic compliance
4af803d build: output error messages on test failures
9ef693e vm: improve context for early errors
6def9fc tests: pass ucode library path through environment
d5dd183 treewide: address various sign-compare warnings
28825ac types: support creating ressource values without associated type
9c5106a types: fix potential memory leaks and null pointer accesses
c51934a types: fix potential leak of key in ucv_object_add()
7b28727 main: fix ineffective EOF check in parse()
4cf897c lib: uc_system(): fix invalid free() of non-heap memory
35af4ba treewide: rework internal data type system
f2c4b79 treewide: fix issues reported by clang code analyzer
93ededb tests: allow executing run_tests.sh from any directory
0e4a387 Add initial GitLab and GitHub CI support
df73b25 tests: add more tests
41d33d0 tests: custom: return exit code if tests fails
1c548a6 cmake: do not output binaries into lib directory
2b59097 tests: create custom tests from current tests cases
8039361 main: provide just binary name in help output
778e4f7 lexer: fix incomplete struct initializers
502ecdc cmake: enable extra compiler checks
3c2aeff cmake: fix includes and libraries
617a114 cmake: make 3.0 minimum version
f360350 lib: implement sleep(ms) function
7f0ff91 lib: allow parsing non-array, non-object value in json()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Change the CONFLICTS definition from the alternative package
(ethtool-full) to the main one.
The CONFLICTS line creates a dependency to the conflicting package.
Right now, the dependency would be created in the PACKAGE_ethtool-full
symbol:
config PACKAGE_ethtool-full
depends on m || (PACKAGE_ethtool != y)
When the main package is selected by airmon-ng, it selects
PACKAGE_ethtool, *depending* on the value of PACKAGE_ethtool-full:
config PACKAGE_airmon-ng
select PACKAGE_ethtool if PACKAGE_ethtool-full<PACKAGE_airmon-ng
In the first block, the value of PACKAGE_ethtool-full depends on the
value of PACKAGE_ethtool. In the second block, the opposite is true:
the value of PACKAGE_ethtool depends on the value of
PACKAGE_ethtool-full. This is a recursive dependency.
Fix it by changing the package where the dependency is created, so that
only the value of PACKAGE_ethtool will depend on PACKAGE_ethtool-full.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The previous procd update broke mounting overlayfs in an attempt to
fix an off-by-one error. Revert that broken fix and apply fix from
Nick Hainke <vincent@systemli.org> instead to bring things back to
life.
20adf53 Revert "initd: fix off-by-one error in mkdev.c"
773e8da initd: fix off-by-one error in mkdev.c
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
