The filogic subtarget now also supports MT7981 and will in future
also support MT7988. Reflect that in the target description.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MT7981 and the upcoming MT7988 have built-in Gigabit Ethernet PHYs.
While they share some design properties with the PHYs present in
MT753x, they do need calibration data from the SoC's efuse.
Add driver to support them. Upstreaming it is planned, but there are
still some ongoing discussions with MediaTek.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport the pinctrl driver for the MT7981 SoC. The driver has also
been submitted upstream and is part of Linux 6.3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport driver for common clocks in MT7981 SoC. The driver has also
been submitted upstream and became part of Linux 6.3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
SOC: MediaTek MT7986
RAM: 512MB DDR3
FLASH: 256MB SPI-NAND (Winbond W25N02KV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
MaxLinear GPY211C 2.5 N-Base-T PHY
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.66/24. Rename the image to tufax4200.bin.
2. Connect the TFTP server to the AX4200. Conect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.66
$ tftpboot 0x46000000 tufax4200.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
----------------
- The LAN port LEDs are driven by the switch but OpenWrt does not
correctly configure the output.
Signed-off-by: David Bauer <mail@david-bauer.net>
The ASUS TUF-AX4200 bootloader adds invalid parameters for the rootfs.
Without overwriting the cmdline, the kernel crashes when trying to
attach the rootfs, as OpenWrt uses a different partition than the vendor
OS.
Signed-off-by: David Bauer <mail@david-bauer.net>
A previous attempt to simplify things went wrong and now sysupgrade
is broken on this device. Fix that.
Fixes: de94587e70 ("mediatek: filogic: don't rely on image preset in flash or sysupgrade")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This variant uses xiaomi factory u-boot and modified u-boot-env &
bootcmd.
By modifying uboot-env, the xiaomi firmware recovery provided in
the vendor u-boot doesn't work anymore. It's possible to put
u-boot into a state where it refuese to take any serial input.
If the u-boot is in this state, users can't restore their
firmware without taking the flash off the board.
We now have a -stock variant where the vendor u-boot is used in
a way that xiaomi firmware recovery still works, and a -ubootmod
variant where we get rid of all xiaomi components, have more
usable space and no uart console lock. These two should cover all
use cases and we don't need this variant anymore.
Drop this redmi-ax6000 variant. Existing users of this variant
should perform a u-boot mod or restore to the -stock layout.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This new layout is only bootable with OpenWrt U-Boot. It reuses the
two crash partions and expands the ubi partion to the end of whole flash.
Do not use this layout with stock U-Boot!
Signed-off-by: Furong Xu <xfr@outlook.com>
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.
1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
be helpful for users who may forget to do this before sysupgrade in
the initramfs.
New flash instructions:
1. Gain ssh access. Please refer to:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)
2. Check which system current u-boot is loading from:
COMMAND: `cat /proc/cmdline`
sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
if firmware=1, current system is ubi1
if firmware=0, current system is ubi0
3. Setup nvram and write the firmware:
If the current system is ubi1, please set it up so that the next time
it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
If the current system is ubi, please set it up so that the next time
it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```
4. After rebooting, the system should now boot into the openwrt initramfs.
Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.
For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:
1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```
2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
add DT nodes and default package for the LEDs on Redmi AX6000
Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Use persistent MAC address for the built-in wireless interfaces of the
BPi-R64 and BPi-R3 development boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This subtarget supports 3 devices:
* Bananapi BPi-R3 (added in a96382c1bb),
* MediaTek MTK7986 rfba AP (added in cffc77ae55),
* MediaTek MTK7986 rfbb AP (added in cffc77ae55).
This subtarget supports DSA from the beginning. It looks like CONFIG_SWCONFIG
was copied from another config when the subtarget was created.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128 MB
RAM: K4A4G165WF-BCWE 512 MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7976GN 2.4GHz ax 4x4
WiFi2: MT7976AN 5GHz ax 4x4
Button: Mesh, Reset
Flash instructions:
1. Gain ssh and serial port access, see the link below:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
2. Use ssh or serial port to log in to the router, and
execute the following command:
nvram set boot_wait=on
nvram set flag_boot_rootfs=0
nvram set flag_boot_success=1
nvram set flag_last_success=1
nvram set flag_try_sys1_failed=8
nvram set flag_try_sys2_failed=8
nvram commit
3. Set a static ip on the ethernet interface of your computer
(e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
4. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
5. Interrupt U-Boot and run these commands:
setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
saveenv
tftpboot initramfs.bin
bootm
6. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Revert to stock firmware:
Restore mtdparts back to default, then use the
vendor's recovery tool (Windows only).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.
Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....
Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC - enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Remove kmod-sdhci-mtk as the mtk-sd driver is built-in anyway for the
relevant subtargets in order to support mounting rootfs from eMMC or
SD card.
Add kmod-iio-mt6577-auxadc to support reading the raw values from the
auxadc unit used as in-SoC thermal sensor. This driver was previously
built-in, but as thermal itself works well without it there is no use
for it in every day use of a device. Build the module to still allow
access to the raw values for those who need it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of trying to figure out the actual root device, just use the
kernel 'root' cmdline parameter as a hint to decide which device to
flash to.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use UBI fast map feature to avoid scanning the whole flash on each
boot which takes several seconds.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of always including the XHCI driver in the kernel on all
MediaTek boards, selectively include the kernel module only on boards
which actually make use of USB functionality.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The newly introduced config symbol CONFIG_CMDLINE_OVERRIDE is only set
for mt7629 for now which breaks automated build on all other mediatek
subtargets. Make sure the symbol is configured as 'is not set' for all
remaining subtargets.
Fixes: c27279dc26 ("mediatek: add support for ipTIME A6004MX Add basic support for ipTIME A6004MX.")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
According to the device tree, the lan ports are
lan0 to lan3, and the wan port is eth1.
Fixes: cffc77a ("mediatek: add filogic subtarget")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
A line in platform.sh was accidentally removed when adding support
for the Bananapi BPi-R3.
Re-add it to fix sysupgrade on the MTK7986 rfba AP.
Fixes: a96382c1bb ("mediatek: add support for Bananapi BPi-R3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Bananapi BPi-R3 is a development router board built around the
MediaTek Filogic 830 (MT7986A) SoC.
The board can boot either from microSD, SPI-NAND, SPI-NOR or eMMC.
Only either SPI-NAND or SPI-NOR can be used at the same time, also only
either microSD or eMMC can be used. The various storage options can be
selected using small SMD switches on the board.
Specs:
* MediaTek MT7986A (Filogic 830) 4x ARM Cortex A53
* 4T4R 2.4G 802.11bgnax (MT7975N)
* 4T4R 5G 802.11anac/ax (MT7975P)
* 2 GB DDR4 RAM
* 8 GB eMMC
* 128 MB SPI-NAND flash
* 32 MB SPI-NOR flash
* on-board MT7531 GbE switch
* 2x SFP+ (1 GbE / 2.5 GbE)
* 5x GbE network port
* miniPCIe slot (only USB 2.0 connected)
* uSIM slot (connected to miniPCIe interface)
* M.2 KEY-E PCIe interface (PCIe x2)
* microSD card interface
* 26 PIN GPIO
Hardware details: https://wiki.banana-pi.org/Banana_Pi_BPI-R3
Working:
* all 4 boot methods incl. installation via U-Boot, sysupgrade, ...
* copper LAN and WAN ports
* SFP1 (connected to gmac1, eth1 in Linux)
* WiFi
* LEDs
* Buttons
* PSTORE/ramoops based dual-boot
Not Working (missing driver features):
* SFP2 (connected to MT7531 switch)
Untested:
* M.2/NGFF slot (PCIe x2)
* mPCIe slot (USB 2.0 + SIM)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Older MT7623 ARMv7 SoC as well as new Filogic platforms come with
inside-secure,safexcel-eip97 units. Enable them in DTS and select the
driver kernel module by default on those platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Initially this covers MT7986 only, but it will later be expanded to cover other
Filogic branded platforms by MediaTek
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
