IPQ806x series also has a GSBI1 with UART and I2C peripherals, so lets add the node for it.
Its needed for Edgecore ECW5410 which uses the UART from GSBI1 as second UART for Bluetooth.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Its needed for Edgecore ECW5410 which does not use QCA8337 switch,
but rather 2x AR8033 PHY-s directly connected to GMAC-s.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This enables the ipq-wifi package to be used on IPQ806x target.
Its needed for boards using a different BDF than one shipped in the upstream board-2.bin.
Currently needed for Edgecore ECW5410.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Router and Movie "keys" are actually switches for both devices
according to the manual. This has been properly implemented in ar71xx,
but overlooked when porting to ath79.
Fixes: 480bf28273 ("ath79: add support for Buffalo WZR-HP-AG300H")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The hardware of this device seems to be identical to WZR-HP-AG300H.
It was already implemented as a clone in ar71xx.
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM
- 32 MiB Flash
- WiFi 5 GHz a/n
- WiFi 2.4 GHz b/g/n
- 5x 1000Base-T Ethernet
- 1x USB 2.0
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Buffalo devices in ath79 share their image generation code,
so let's create a shared Device definition for them.
Since most of them use BUFFALO_HWVER := 3, this is moved as
default to the shared definition as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The tp-link safeloader devices typically contain a partition
"default-mac" which stores the MAC addresses. It is followed by other
partitions containing device info, like
{"default-mac", 0x610000, 0x00020},
{"pin", 0x610100, 0x00020},
{"product-info", 0x611100, 0x01000},
In DTS, we typically assign a 0x10000 sized partition for these,
which is mostly labelled "mac" or "info". In rarer cases, the
partitions have been enclosed in a larger "tplink" or "config"
partition.
However, when comparing different devices, the implementation appears
relatively arbitrary at the moment.
Thus, this PR aims at harmonizing these partitions by always using
the name "info" for the DTS partition containing "default-mac".
"info" is preferred over "mac" as we never just have "default-mac"
alone, but always some other device-info partitions as well.
While at it, this also establishes a similar partitioning for the
few devices where the "info" partitions are part of a bigger
unspecific "config" partition or similar.
Besides the harmonization itself, this also allows to merge a few
cases in 11-ath10k-caldata.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
vconfig has been disabled by default since 2015 [1] and there are
no remaining uses in entire OpenWrt trunk. However, we still set up
a specific name_type for it during boot.
While this setup is properly implemented to be only triggered when
vconfig is present, it still seems anachronistic and unnecessary
to set up a standard for a tool that is not used anymore.
Therefore, this removes the set_name_type initialization and leaves
it for those people actually using the tool to configure it as needed.
[1] 899a23227e ("busybox: improve applets & deprecate ifconfig, route")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Assign return value of kstrtoul to error variable instead of
conversion value.
Suggested-by: Birger Koblitz <git@birger-koblitz.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Do some minor empty lines cleanup, i.e. remove those at EOF and
add some for cosmetic reasons/consistency.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 34cc2c9a99.
The reverted shell code is a very poor reimplementation of the existing
package-metadata.pl usergroup subcommand and the resulting file is not
used anymore, so drop this code.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Use the prepared .packageusergroup file to lookup user and group names
when processing the passed file mode.
Also replace the various subshell/cut invocations with a sequence of
standard variable interpolations which fixes paths with embedded colons
as a side-effect.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This file can be subsequently used to resolve symbolic user or group names
to their numeric IDs when packing ipk archives.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
With the introduction of `./tmp/userids` the `ipkg-build` script can now
resolve values of "PKG_FILE_MODES", allowing users to set names rather
than numeric values.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Multiple packages contain a USERID variable defining required user and
group for the package to run. With the recent addition of
"PKG_FILE_MODES" it is possible to define user and group of specific
files, replacing (possibly insecure) post-inst scripts. These modes are
set during build time and put directly into the packages.
To allow user and group names rather than the numeric values, a mapping
like `/etc/passwd` is required by the `ipkg-build` script, mapping names
defined in "PKG_FILE_MODES" to a numeric value, as the build system does
not create any users during build.
This commit adds a single line to the `prepare-tmpinfo` target, so that
everytime the feeds are updated the *passwd like* content of
`./tmp/userids` is updated.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This adds support for the RTL838x Architecture.
SoCs of this type are used in managed and un-managed Switches and Routers
with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash,
Ethernet including a DSA switch driver and internal and external PHYs used
with these switches.
Supported SoCs:
RTL8380M
RTL8381M
RTL8382M
The kernel will also boot on the following RTL839x SoCs, however driver
support apart from spi-nor is missing:
RTL8390
RTL8391
RTL8393
The following PHYs are supported:
RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port)
RTL8218B internal: internal PHY of the RTL838x chips
RTL8318b external (QSGMII 8-port GMAC phy)
RTL8382M SerDes for 2 SFP ports
Initialization sequences for the PHYs are provided in the form of
firmware files.
Flash driver supports 3 / 4 byte access
DSA switch driver supports VLANs, port isolation, STP and port mirroring.
The ALLNET ALL-SG8208M is supported as Proof of Concept:
RTL8382M SoC
1 MIPS 4KEc core @ 500MHz
8 Internal PHYs (RTL8218B)
128MB DRAM (Nanya NT5TU128MB)
16MB NOR Flash (MXIC 25L128)
8 GBEthernet ports with one green status LED each (SoC controlled)
1 Power LED (not configurable)
1 SYS LED (configurable)
1 On-Off switch (not configurable)
1 Reset button at the right behind right air-vent (not configurable)
1 Reset button on front panel (configurable)
12V 1A barrel connector
1 serial header with populated standard pin connector and with markings
GND TX RX Vcc(3.3V), connection properties: 115200 8N1
To install, upload the sysupgrade image to the OEM webpage.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Add support for uimage headers from ALLNET and provide support for the
SG8208M and SG8310PM devices' magic bytes.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This target has not been updated to 5.4 yet, and the only person
trying it (Koen) decided to retreat based on the following reasons:
- The target is not DT-aware at all
- The huge amount of effort required
- The SoC itself reached EoL at Cavium for some time now
- Upstream removed some important parts as it's also slowly getting EoL
over there
- The commercial product that used this will fade out shortly
- The amount of download for this binary suggest that the target is not
that popular
Since nobody has picked up the work since then, and this is the last
remaining 4.19-only target, finally drop it now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On the Turris Omnia 2019, u-boot environment is located at 0xF0000, instead
of 0xC0000. The switch happened with u-boot-omnia package version 2019-04-2
(May 10, 2019).
Check the installed u-boot release, and set the default accordingly.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
[bump PKG_RELEASE, use lower case for hex offset]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
this board has a pcie to sata bridge connected to pcie2 with a
separated pcie reset on gpio7.
add reset-gpios and corresponding pinctrl nodes into dts.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Backport upstream changes to initialize GDM settings and reset PPE
Allow GMAC to recognize the special tag to fix PPE packet parsing
Improve GRO performance by passing PPE L4 hash as skb hash
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All modifications made by update_kernel.sh/no manual intervention needed
Build-tested: x86_64
Run-tested: ipq806x (R7800)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.
The device was kindly provided for porting by Stijn Segers.
Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
* Eth0 (back): 802.3af/at PoE in
* Eth1, Eth2 (bottom)
* Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
* LED button, implemented as KEY_BRIGHTNESS_TOGGLE
* Reset button
Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
Do NOT bridge R164
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
br0 Link encap:Ethernet HWaddr 50:...:04
eth0 Link encap:Ethernet HWaddr 50:...:04
wifi0 Link encap:UNSPEC HWaddr 50-...-04-...
wifi1 Link encap:UNSPEC HWaddr 50-...-05-...
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
HooToo HT-TM05 and RAVPower RP-WD03 have almost identical hardware
(except for RAM size) and are from the same vendor (SunValley).
Create a common DTSI file for them.
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The baud rate for the RAVPower RP-WD03 is 57600, not 115200.
Since this is the default from mt7620n.dtsi, the chosen node can
simply be removed from the device DTS.
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to the User Manual, there is a "Wi-Fi LED" with blue and
green colors, doing the following by default:
Flashing Blue: System loading
Solid Blue: System loaded
Flashing Green: Connecting to the Internet
Solid Green: Connected to the Internet
According to this vendor behavior, we keep refer to the LED as "wifi"
but implement the according default behavior as in OEM firmware.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MAC assignment based on vendor firmware:
2.4 GHz *:b4 (factory 0x04)
LAN/label *:b4 (factory 0x28)
WAN *:b5 (factory 0x2e)
The previously used location 0x4000 for ethernet is actually empty.
Therefore, fix the ethernet MAC address and set it as label-mac-address.
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.
To address this, use the lzma loader (loader-okli) to work around this
limitation.
The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.
Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enable the VLAN tag offloading mechanism for RGMII single-port devices.
This allows those devices to use 802.1Q VLANs on the ethernet port.
Previously, RX frames were double tagged, as the RX TAG removal flag was
not enabled and an additional 802.1Q header was inserted elsewhere in
the code.
On the TX side, tagging was completely not present for single-port
devices. Enable tagging if an 802.1Q frame should be transmitted and
disable the default tagging mechanism for single-port devices.
Tested on Aruba AP-303
Signed-off-by: David Bauer <mail@david-bauer.net>
Add support for per-BSS airtime weight configuration. This allows to set
a airtime weight per BSS as well as a ratio limit based on the weight.
Support for this feature is only enabled in the full flavors of hostapd.
Consult the hostapd.conf documentation (Airtime policy configuration)
for more information on the inner workings of the exposed settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
Set the default state for LEDs to off. When a trigger is set, the
trigger will turn the LED automatically on.
Currently LEDs might stay on, e.g. when the LED trigger is set to a
netdev trigger and the interface is never activated or the 'none'
trigger is selected without setting the 'default' option to 0 and it's
set for the LED indicating the system running state.
Using off as a default value is also consistent with the documentation
in the OpenWrt wiki.
Signed-off-by: David Bauer <mail@david-bauer.net>
TITLE is "NFS4 filesystem client support" (Line 428)
but the description is "Kernel module for NFS v4 support" (Line 438).
Use "Kernel module for NFS v4 client support" on line 438.
Signed-off-by: Bob Cai <1119283622@qq.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
vconfig is no more installed by default to a firmware image. So, replace
vconfig calls for VLAN subinterface configuration by coresponding
ip-link commands.
Also drop few useless comments from the preinit hook script, while we
are at it.
I have no chance to test this fix since I have no board with a subject
switch IC, but this is still better then call an utility that is
unavailable in the firmware for years.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[use documented syntax for ip link add]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since the introduction of fakeroot support, wrapped SDK executables might
be invoked from a shell that has libfakeroot.so preloaded.
Since we're using preloading as well in order to mangle argv[0] when
invoking the shipped ELF interpreter directly, we must take care of
preloading the already preloaded libraries as well, to avoid invoked
programs losing their fakeroot capabilities.
Extend the bundle-libraries.sh script to take any existing $LD_PRELOAD
into account when invoking the target ELF executable with a preloaded
runas.so library.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
