Commit Graph

2597 Commits

Author SHA1 Message Date
Birger Koblitz
8007853f79 ramips: remove unnecessary nodes in DTS for Edimax RG21S
This sdhci and i2c nodes were copy-pasted, but are not needed as
the device does not provide that functionality. Remove them.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[added commit title/message, split patch]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-17 13:32:57 +01:00
DENG Qingfang
1b7199c90c ramips: add support for JCG JHR-AC876M
JCG JHR-AC876M is an AC2600M router

Hardware specs:
  SoC: MT7621AT
  2.4GHz: MT7615N 4x4 @ PCIe0
  5GHz: MT7615N 4x4 @ PCIe1
  Flash: Winbond W25Q128JVSQ 16MiB
  RAM: Nanya NT5CB128M16 256MiB
  USB 2.0 and 3.0 ports
  6 LEDs, 3 of which are connected to SoC GPIO
  Reset and WPS buttons

Flash instructions:
Stock to OpenWrt:
  Upload factory.bin in stock firmware's upgrade page,
  do not preserve settings

OpenWrt to stock:
  Push and hold the reset button for 5s while power cycling to
  enter recovery mode;
  Visit 192.168.1.1 and upload stock firmware

MAC addresses map:
  0x0004  *:1c  wlan2g/wan/label
  0x8004  *:20  wlan5g
  0xe000  *:1b  lan
  0xe006  *:1a  not used in stock fw

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-12-13 19:43:47 +01:00
Adrian Schmutzler
0bf4d681d4 ramips: allow JCG_MAXSIZE in kiB in Build/jcg-header
This allows JCG_MAXSIZE to be specified in kilobytes. This makes
this value more consistent and easier comparable with other size
variables.

This also changes the only occurence of the variable, for Cudy WR1000.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-13 19:43:30 +01:00
Sungbo Eo
a972b1fb5f ramips: add support for ipTIME A6ns-M
ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: MT7615
  - 5GHz: MT7615
- Ethernet: 5x 10/100/1000Mbps
  - Switch: SoC internal
- UART:
  - J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-12-13 19:42:48 +01:00
Adrian Schmutzler
5cda133d99 ramips: DTS style improvements for mt7621_wevo_w2914ns-v2.dtsi
This does several trivial DTS style improvements:

- Move device name compatible to DTS files (and fix compatible in
  11acnas.dts)
- Remove xhci node as status is set to okay in mt7621.dtsi already
- 0x0 instead of 0x0000
- Simplify state_default node definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-13 15:37:58 +01:00
Sungbo Eo
0375c076b6 ramips: add support for ZIO FREEZIO
ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: MT7603EN
  - 5GHz: MT7612EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: SoC internal
- USB: 1x 3.0
- UART:
  - J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1

Notes:
- FREEZIO has almost the same board as WeVO W2914NS v2.
- Stock firmware is based on OpenWrt BB.

MAC addresses in factory partition:
0x0004: WiFi 2.4GHz (label_mac-8)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-4)
0xe000: LAN (label_mac+1)

Installation via web interface:
1.  Access web admin page and turn on "OpenWrt UI mode".
2.  Flash sysupgrade image through LuCI, with the "Keep settings" option
    OFF.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.
    Make sure to NOT preserve settings.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebase, use mt7621_wevo_w2914ns-v2.dtsi]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-13 15:37:37 +01:00
Adrian Schmutzler
68ef534989 ramips: add label MAC address for Mikrotik RBM33G
The device label contains:
E01: B8:69:F4:xx:xx:07
E02: B8:69:F4:xx:xx:09

The first value corresponds to the address set in hard_config 0x10.

That one is taken for the label MAC address.

Thanks to Martin Schiller for retrieving the information.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:12:11 +01:00
Adrian Schmutzler
772af7f98d ramips: rt305x: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

This removes the wan_mac setup for the following devices as they
do not set up a MAC address for ethernet in the first place:
- asiarf,awapn2403
- belkin,f7c027
- dlink,dir-615-d
- mofinetwork,mofi3500-3gn
- prolink,pwh2004
- ralink,v22rw-2x2
- unbranded,wr512-3gn-4m
- unbranded,wr512-3gn-8m

While at it, make some DT node labels consistent with the label
property.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:58 +01:00
Adrian Schmutzler
a858d6d0e2 ramips: rt288x: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

This removes the wan_mac setup for ralink,v11st-fe as this device
does not set up a MAC address for ethernet in the first place.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:49 +01:00
Adrian Schmutzler
fef1810897 ramips: mt76x8: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

While at it, change the partition label for zyxel,keenetic-extra-ii
to factory to be consistent with node label and all the other devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:39 +01:00
Adrian Schmutzler
ed975a58e4 ramips: mt7621: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:28 +01:00
Adrian Schmutzler
98d9158d2f ramips: mt7620: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:18 +01:00
Adrian Schmutzler
38866f275d ramips: remove wan_mac setup for evaluation boards
The evaluation boards do not set up a MAC address for eth0
in the first place, so it does not make sense to calculate a WAN
address from the random MAC used there.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:11 +01:00
Adrian Schmutzler
757658f2ab ramips: create common DTSI for TP-Link Archer C20i/C20 v1/C50 v1
The TP-Link Archer C20i/C20 v1/C50 v1 seem to be almost the same,
so creating a common DTSI will reduce duplicate code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:04 +01:00
Adrian Schmutzler
c4f6850efc ramips: remove unused DTS variable from DEVICE_VARS
The DTS variable has been removed in 402138d12d ("ramips: Derive
DTS name from device name in Makefile"), but the DEVICE_VARS entry
has been overlooked.

Remove it now since we are not using this variable.

This must _not_ be backported to 19.07, where the variable is still
in use.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:10:57 +01:00
Gabor Varga
a283b1788a ramips: fix switch port numbering for RT-AC65P/RT-AC85P
The switch LAN port numbers are in reversed order with original config.
With this patch they are fixed.

Port order checked on both devices.

Signed-off-by: Gabor Varga <vargagab@gmail.com>
[merged definitions into appropriate block, extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-11 23:00:32 +01:00
Adrian Schmutzler
e00396d584 ramips: add label MAC address for TP-Link Archer C20i
Current OpenWrt MAC setup:
eth0             &rom 0xf100    :48
eth0.2           eth0+1         :49
wlan0 (5 GHz)    &radio 0x8004  different OUI
wlan1 (2.4 GHz)  &radio 0x4     same OUI as wlan0

Label MAC address corresponds to eth0 (&ethernet).

No additional addresses found in hexdump of rom/radio.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-11 22:51:04 +01:00
Koen Vandeputte
d395583d69 kernel: bump 4.14 to 4.14.158
Refreshed all patches.

Altered patches:
- 400-mtd-add-rootfs-split-support.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-12-10 09:50:42 +01:00
Adrian Schmutzler
231dc26867 treewide: remove dts-v1 identifier from DTSI files
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.

This removes the identifier from all DTSI files in /target/linux.

Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx

This does not touch ipq806x for now, as the bump to 4.19 is close.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 16:44:06 +01:00
Adrian Schmutzler
34abfb6e91 ramips: convert mediatek,mtd-eeprom from decimal to hex notation
A small subset of devices uses decimal notation for mediatek,mtd-eeprom
in DTS files. Convert to hexadecimal notation to be consistent with
all the rest.

Also change "0" to "0x0" in the same files for consistency.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 00:20:37 +01:00
Martin Schiller
3a55c7935d ramips: fix number of LAN Ports for Mikrotik RBM33G
The Mikrotik RBM33G has only 2 LAN ports.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[moved node in 02_network to maintain alphabetic sorting]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 00:20:21 +01:00
Walter Sonius
a065cd29bf ramips: fix switch port order for TP-Link Archer C20i
Physical port order watched from the backside of the C20i
(from left to right) is: Internet / 1 / 2 / 3 / 4

Physical Port	Switch port
WAN             0
LAN 3           1
LAN 4           2
LAN 1           3
LAN 2           4
(not used)      5
CPU             6

Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[commit message/title improvements]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 00:20:12 +01:00
Koen Vandeputte
414b7c107a kernel: bump 4.14 to 4.14.156
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-29 09:59:49 +01:00
David Bauer
6a76ea359b ramips: reorganize NETGEAR sercomm boards
This re-organizes the device-tree files for the Sercomm-manufactured
NETGEAR routers. They are now split into two different base-boards,
from which the respective model is extended.

This partially reverts commit c7842ceaaa ("ramips: reorganize DTSI
files for Netgear R devices"), which introduced inheritance between two
completely unrelated base-boards.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-24 23:17:20 +01:00
Koen Vandeputte
d6aea46a50 kernel: bump 4.14 to 4.14.154
Refreshed all patches.

Altered patches:
- 902-debloat_proc.patch
- 040-dmaengine-qcom-bam-Process-multiple-pending-descript.patch
- 807-usb-support-layerscape.patch
- 809-flexcan-support-layerscape.patch
- 816-pcie-support-layerscape.patch

Remove upstreamed:
- 150-MIPS-bmips-mark-exception-vectors-as-char-arrays.patch
- 303-spi-nor-enable-4B-opcodes-for-mx66l51235l.patch

New symbols:
X86_INTEL_MPX
X86_INTEL_MEMORY_PROTECTION_KEYS
X86_INTEL_TSX_MODE_OFF
X86_INTEL_TSX_MODE_ON
X86_INTEL_TSX_MODE_AUTO
SGL_ALLOC

Compile-tested on: cns3xxx, x86_64
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-19 14:59:03 +01:00
Sungbo Eo
19800ac095 ramips: set uImage name of WeVO 11AC NAS and W2914NS v2
The stock firmware and bootloader only accept uImage with names that
match certain patterns. This patch enables OpenWrt installation from
stock firmware without having to reflash the bootloader or access the
UART console.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-17 14:01:31 +01:00
Christian Lamparter
ad65d9d7b2 ramips: assign correct key-code to wps buttons
The ASUS WL-330N(3G) and the Edimax RG21S had the
reset keycode assigned to the WPS button. This patch
changes all three devices to use KEY_WPS_BUTTON in
the hopes that this fixes unwanted restarts/
unexpected behavior from the users point of view.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-11-16 22:37:51 +01:00
Piotr Dymacz
e68539aca4 ramips: add support for ALFA Network Quad-E4G
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.

Specification:

- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)

Other:

- U-Boot selects default SIM slot, based on value of 'default_sim' env
  variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
  has additional logic circuit for M.2 SIM switching. The 'sim-select'
  will work only if both SIM slots are occupied. Otherwise, always slot
  with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
  loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
  U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
  has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
  miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
  slots but setting GPIO22 to high allows PERSTn control per slot, using
  GPIO23-25 (value is inverted)

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the modem LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-14 01:37:54 +01:00
Piotr Dymacz
44d7a14a83 ramips: mt7621: refresh kernel config
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-14 00:11:09 +01:00
Piotr Dymacz
fc0d0f5dfd ramips: provide label MAC for ALFA Network Tube-E4G
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-14 00:10:52 +01:00
Piotr Dymacz
dfecf94c20 ramips: add support for ALFA Network R36M-E4G
ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform
based on MediaTek MT7620A WiSoC. This product is designed for operation
with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06)
but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses).

Specification:

- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32+ MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 2x u.fl antenna connectors (for Wi-Fi)
- 8x LED (7 driven by GPIO)
- 2x button (reset, wifi)
- 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB
- 1x I2C (4-pin, 1.27 mm pitch) header on PCB
- 1x LED (8-pin, 1.27 mm pitch) header on PCB
- 1x DC jack with lock (12 V)

Other:

- there is a dedicated, 4-pin connector for optional RTC module (Holtek
  HT138x) with 'enable' input, not available at the time of preparing
  support for this board
- miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a
  jumper resistor (R174) is not installed by default
- U-Boot selects default SIM slot, based on value of 'default_sim' env
  variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will
  work only if both slots are occupied, otherwise U-Boot will always
  select slot with SIM card inside (user can override it later, in
  user-space)
- U-Boot resets the modem, using PERSTn signal, before starting kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
  U-Boot environment variable)

Flash instruction:

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the modem LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-13 21:45:31 +01:00
Piotr Dymacz
bc173ddd83 ramips: support dual image feature on ALFA Network boards
New U-Boot version for MediaTek MT76x8/MT762x based ALFA Network boards
includes support for a 'dual image' feature. Users can enable it using
U-Boot environment variable 'dual_image' ('1' -> enabled).

When 'dual image' feature is enabled, U-Boot will modify DTB and divide
the original 'firmware' flash area into two, equal in size and aligned
to 64 KB partitions: 'firmware' and 'backup'. U-Boot will also adjust
size of 'firmware' area to match installed flash chip size.

U-Boot will load kernel from active partition which is marked with env
variable 'bootactive' ('1' -> first partition, '2' -> second partition)
and rename both partitions accordingly ('firmware' <-> 'backup').

There are 3 additional env variables used to control 'dual image' mode:
- bootlimit   - maximum number of unsuccessful boot tries (default: '3')
- bootcount   - current number of boot tries
- bootchanged - flag which informs that active partition was changed; if
                it is set and 'bootcount' reaches 'bootlimit' value,
                U-Boot will start web-based recovery which then updates
                both partitions with provided image

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-13 21:45:31 +01:00
Sungbo Eo
261c746631 ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100
CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing
in default images. This commit adds it.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[changed commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-13 16:21:59 +01:00
Sungbo Eo
fe6a04a8fe ramips: change status LED of Samsung CY-SWR1100
Use power LED for status indication and free WPS LED for other uses.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-13 16:05:19 +01:00
Sungbo Eo
aabdf6991c ramips: improve Samsung CY-SWR1100 support
This patch does the following:

- rename "devdata" flash partition and make it read-only
- switch from gpio-keys-polled to gpio-keys
- add missing power LED
- set correct PCI ID to compatible string in wifi node
- remove ralink,5ghz property in wifi node
- provide label MAC address

Rename devdata partition to devconf as indicated in the stock firmware
partition table:
00030000-00040000: "devdata"
00040000-00050000: "devconf"

Power LED can be controlled by SoC GPIO. Add it in the dts leds node.

RT3092L supports only bgn mode, so it is unnecessary to disable 5GHz band.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-13 16:03:42 +01:00
Sungbo Eo
7231c1edd9 ramips: fix MAC address setup for Samsung CY-SWR1100
Ethernet MAC address setup has been broken since c3e420f28c. Restore
original setting.

Fixes: c3e420f28c ("ramips: Add support for D-Link DCH-M225")

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-13 15:57:53 +01:00
Adrian Schmutzler
f4c3cfc620 ramips: read label MAC address from flash instead of using phy0/phy1
This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress)
by retrieval from the proper flash locations. This will make
02_network independent of WiFi setup again.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-13 12:51:38 +01:00
Adrian Schmutzler
1c321237c2 ramips: split further base-files across subtargets
As started in 19724e28c8 ("ramips: split base-files into
subtargets"), this moves some smaller left-over files to the
appropriate base-files folder of their subtarget:

- /etc/init.d/bootcount
- /etc/uci-defaults/04_led_migration

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-11 14:53:06 +01:00
David Bauer
b16d76bf40 ramips: correct Netgear WNDR3700v5 button flag
This adjusts the GPIO state flag to ACTIVE_LOW as FCC pictures indicate
the base board is identical to the one of the R6220.

Fixes commit 3459013257 ("ramips: correct R6220 button flag")

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-10 20:57:16 +01:00
David Bauer
3459013257 ramips: correct R6220 button flag
All buttons on the Netgear R6220 are active-low while they are flagged
as active-high.

The GPIO status reads the following for no buttons pressed:

root@64367-r6220:~# cat /sys/kernel/debug/gpio
gpio-7   (                    |wps                 ) in  hi
gpio-8   (                    |wifi                ) in  hi
gpio-14  (                    |reset               ) in  hi

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-09 19:15:40 +01:00
Adrian Schmutzler
f098c612b6 ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3
This moves shared code of the named devices into a common DTSI.

Remove setting status="okay" for &gpio0 as it's not disabled in
mt7620a.dtsi.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:17:31 +01:00
Frederik Noe-Sdun
4a904b8b76 ramips: increase max SPI frequency to 50 MHz for EX3700/EX6130
Based on Macronix MX25L3205DM2I datasheet this is maximum
supported speed.

Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, improved commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:17:25 +01:00
Frederik Noe-Sdun
0cbd2c74d0 ramips: add support for Netgear EX6130
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The -factory images can be flashed from the
device's web interface or via nmrpflash.

The device seems to use base PCB as EX3700/EX3800,
but supporting AC1200 using MT7612E.

MAC adresses:
5.0 GHz  0x8004  *:9a
2.4 GHz  0x4     *:9b
lan      0x28    *:9b
wan      0x2e    *:9c

Since this is a one-port device, although wan MAC address is
set in flash, it is not used in OpenWrt setup.

Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, extended commit message, tiny DTS style fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:16:14 +01:00
Adrian Schmutzler
a921945773 ramips: rename keys node formerly named button
For some devices, the keys node is named "button". Change name to
match the rest of the target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-07 17:13:18 +01:00
Paul Spooren
9fa061a7d3 ramips, mt7620: reproducible elecom-header uid/gid
The elecom-header renames the firmware image to v_0.0.0.bin, stores its
MD5 sum as v_0.0.0.md5 and tars both files again.

Both v_0.0.0 files are created as the build user making it harder to
reproduce.

This commit sets the owner/group of both files to root by adding extra
options to the final tar command.

Before:
0 buildbot   (101) buildbot   (102)  3932164 2019-11-05 14:43:22.000000 v_0.0.0.bin
0 buildbot   (101) buildbot   (102)       33 2019-11-05 14:43:22.000000 v_0.0.0.md5

After:
0 root         (0) root         (0)  3932164 2019-11-05 23:43:08.000000 v_0.0.0.bin
0 root         (0) root         (0)       33 2019-11-05 23:43:08.000000 v_0.0.0.md5

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-11-06 23:23:52 +01:00
Adrian Schmutzler
c7842ceaaa ramips: reorganize DTSI files for Netgear R devices
This reorganizes DTSI files for the Netgear R devices in mt7621
(and the WNDR3700 v5). It creates a common DTSI for all R (sercomm)
devices and distributes the remaining code in r6220.dtsi to R6220
and WNDR3700 v5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 14:43:04 +01:00
Sungbo Eo
62b1559b56 ramips: improve support for WeVO 11AC NAS and W2914NS v2
- remove WAN port index
- load WAN MAC address directly from the flash
- provide label MAC address
- increase flash's SPI frequency to 80MHz
- add mt76 led nodes to make WiFi LEDs work
- drop unnecessary pinmux groups

The factory partition scheme for MAC addresses (verified on both devices):
0x4   : WiFi 2.4GHz (label_mac-9)
0x28  : unused
0x2e  : WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-5)
0xe000: LAN (label_mac-1)
0xe006: unused

By improving flash speed,
`time dd if=/dev/mtdblock3 of=/dev/null bs=64k`
has been reduced from 14.51s to 3.11s.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebased]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 14:31:32 +01:00
Adrian Schmutzler
d2b9333ea9 ramips: remove default case for MAC address assignment
So far, MAC address assignment in ramips has contained a default
case, which defined wan_mac = eth0 + 1 for _every_ device not
having an explicit case there.

This is not desirable, as many device supporters will just not
care or know about this definition, so another MAC address will be
introduced by accident. In some cases the wan_mac is assigned
although it is not needed, in other cases even addresses not
dedicated to the device will be used (e.g. wan_mac actually is
eth0 - 1, but during support nobody cared, so eth0 + 1 is used now,
which might actually belong to another device ...).

Thus, in this PR the former default case is converted to an
explicit case. This one comprises all devices not being accounted
for by other cases, reduced by those not having wan at all.
The big number of entries for this node might be another indication
that many of them wouldn't actually be there if there hadn't been
default wan_mac setup.

In exchange, the current "do nothing" case can be removed, as it
will be the new default case.

The devices being put in the newly created explicit case were
determined as follows:

1. Create a list of all devices based on the DTS files.

2. Remove all devices already having an explicit entry setting
   their address.

3. Remove all devices that only have lan set up in the first part
   of 02_network:

mt7620:
   - alfa-network,tube-e4g
   - asus,rp-n53
   - buffalo,wmr-300
   - comfast,cf-wr800n
   - edimax,ew-7476rpc
   - edimax,ew-7478ac
   - elecom,wrh-300cr
   - hnet,c108
   - kimax,u25awf-h1
   - kimax,u35wf
   - kingston,mlw221
   - kingston,mlwg2
   - microduino,microwrt
   - netgear,ex2700
   - netgear,ex3700
   - netgear,wn3000rp-v3
   - planex,cs-qr10
   - planex,mzk-ex300np
   - planex,mzk-ex750np
   - ravpower,wd03
   - sercomm,na930
   - yukai,bocco
   - zbtlink,zbt-cpe102
   - zte,q7

mt7621:
   - gnubee,gb-pc1
   - gnubee,gb-pc2
   - linksys,re6500
   - mikrotik,rbm11g
   - netgear,ex6150
   - thunder,timecloud
   - tplink,re350-v1
   - tplink,re650-v1

mt76x8:
   - alfa-network,awusfree1
   - d-team,pbr-d1
   - glinet,vixmini
   - vocore,vocore2-lite
   - tama,w06
   - tplink,tl-mr3020-v3
   - tplink,tl-wa801nd-v5
   - tplink,tl-wr802n-v4
   - tplink,tl-wr902ac-v3
   - vocore,vocore2
   - widora,neo-16m
   - widora,neo-32m

rt288x:
   - buffalo,wli-tx4-ag300n
   - dlink,dap-1522-a1

rt305x:
   - allnet,all0256n-4m
   - allnet,all0256n-8m
   - allnet,all5002
   - allnet,all5003
   - alphanetworks,asl26555-16m
   - alphanetworks,asl26555-8m
   - asus,wl-330n
   - aximcom,mr-102n
   - dlink,dcs-930
   - easyacc,wizard-8800
   - hame,mpr-a2
   - hootoo,ht-tm02
   - huawei,d105
   - intenso,memory2move
   - planex,mzk-dp150n
   - rt305x dlink,dcs-930l-b1
   - sparklan,wcr-150gn
   - tenda,3g150b
   - tenda,3g300m
   - tenda,w150m
   - trendnet,tew-638apb-v2
   - unbranded,a5-v11
   - vocore,vocore-16m
   - vocore,vocore-8m
   - wansview,ncs601w
   - zorlik,zl5900v2

rt3883:
   - loewe,wmdr-143n
   - omnima,hpm

4. Put the remaining devices in the new case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:17:25 +01:00
Sungbo Eo
763914ef1b ramips: improve netis WF-2881 support
This patch does the following:

1. remove u-boot-env partition
   Stock bootloader saves env variables at 0x80000 in flash,
   and there is nothing stored at 0x30000.
   By merging the partition "u-boot-env" with "u-boot",
   the partition table becomes the same as used in stock firmware:
   00000000-00080000: "Bootloader"
   00080000-00100000: "Config"
   00100000-00140000: "Factory"
   00140000-07f80000: "Kernel"

2. fix LAN/WAN MAC addresses and provide label MAC address
   Ethernet MAC addresses are stored in factory partition at:
   0xe000: LAN (label_mac)
   0xe006: WAN (label_mac+1)

3. fix LAN port order
   WF-2881 LAN ports are in reverse order of switch ports.

4. fix WiFi LEDs
   mt76 led nodes are added to make WiFi LEDs work.
   On top of this, mt76 node names are changed to more generic ones,
   and compatible strings are also added.

5. fix pinmux groups
   uart3 and uart2 pins are used as button and led, but jtag pins are not.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-06 00:27:55 +01:00
Sungbo Eo
6ea5f7d44c ramips: fix MTK_SOC for RT3662 devices
rt3883.mk contains both RT3662 and RT3883 device profiles, but commit
6a104ac772 set MTK_SOC to rt3883 for all devices. This patch fixes it,
and renames dts files accordingly. And SoC compatible strings are also
appended in the dts.

Fixes: 6a104ac772 ("ramips/rt288x,rt3883: Name DTS files based on scheme")

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-04 15:22:54 +01:00