This makes use of cfg80211 feature backported & described in
188626f17c ("mac80211: backport cfg80211 support for
ieee80211-freq-limit DT property").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Most mac80211 drivers leave the SMPS field in the HT capabilities
uninitialized (unfortunately defaults to static SMPS), which leads to
some devices limiting themselves to single-stream rates in some modes
(mostly mesh and IBSS).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This property allows specifying extra limits for wireless device in DT.
For a full documentation see upstream commit b330b25eaabd ("dt-bindings:
document common IEEE 802.11 frequency limit property").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This reverts commit 528f46d082.
After this commit, several users reported stability issues. Revert it
now so it doesn't cause issues for the upcoming release
Signed-off-by: Felix Fietkau <nbd@nbd.name>
An external reset patch for AR955x accidentally led to external reset
being issued twice on AR913x, once before the RTC reset and once after.
This may be causing some stability issues.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit was added to improve reset time on old SoC devices that run
into chip hangs more frequently. However with the more recent addition
of full WMAC reset on these chips, it could be problematic.
Drop this patch to ensure that DMA activity is really stopped before the
chip reset is issued
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds a patch that introduces airtime fairness scheduling to ath9k,
which can significantly improve network efficiency in mixed-rate
environments.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds a patch that introduces airtime fairness scheduling to ath9k,
which can significantly improve network efficiency in mixed-rate
environments.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The patch commit states:
"It's possible to make scanning consume almost arbitrary amounts
of memory, e.g. by sending beacon frames with random BSSIDs at
high rates while somebody is scanning.
Limit the number of BSS table entries we're willing to cache to
1000, limiting maximum memory usage to maybe 4-5MB, but lower
in practice - that would be the case for having both full-sized
beacon and probe response frames for each entry; this seems not
possible in practice, so a limit of 1000 entries will likely be
closer to 0.5 MB."
Signed-off-by: Johannes Berg <johannes.berg@intel.com>"
This patch was added in 4.4.36. But because LEDE backports
cfg80211, mac80211 and the wifi drivers separately, it needs
to be added manually for now. It can be dropped later as it
will be part of the next mac80211 refresh.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
These properties allow overriding the settings from the EEPROM
which indicate whether a band is enabled or not.
Setting this property is only needed when the RF circuit does not
support the 2.4GHz or 5GHz band while it is enabled nevertheless in the
EEPROM.
These patches will be replaced with a future upstream version which
will introduces an ieee80211 device tree property to disable bands.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
There are two types of swapping the EEPROM data in the ath9k driver.
Before this series one type of swapping could not be used without the
other.
The first type of swapping looks at the "magic bytes" at the start of
the EEPROM data and performs swab16 on the EEPROM contents if needed.
The second type of swapping is EEPROM format specific and swaps
specific fields within the EEPROM itself (swab16, swab32 - depends on
the EEPROM format).
With this series the second part now looks at the EEPMISC register
inside the EEPROM, which uses a bit to indicate if the EEPROM data
is Big Endian (this is also done by the FreeBSD kernel).
This has a nice advantage: currently there are some out-of-tree hacks
(in OpenWrt and LEDE) where the EEPROM has a Big Endian header on a
Big Endian system (= no swab16 is performed) but the EEPROM itself
indicates that it's data is Little Endian. Until now the out-of-tree
code simply did a swab16 before passing the data to ath9k, so ath9k
first did the swab16 - this also enabled the format specific swapping.
These out-of-tree hacks are still working with the new logic, but it
is recommended to remove them. This implementation is based on a
discussion with Arnd Bergmann who raised concerns about the
robustness and portability of the swapping logic in the original OF
support patch review, see [0].
After a second round of patches (= v1 of this series) neither Arnd
Bergmann nor I were really happy with the complexity of the EEPROM
swapping logic. Based on a discussion (see [1] and [2]) we decided
that ath9k should use a defined format (specifying the endianness
of the data - I went with __le16 and __le32) when accessing the
EEPROM fields. A benefit of this is that we enable the EEPMISC based
swapping logic by default, just like the FreeBSD driver, see [3]. On
the devices which I have tested (see below) ath9k now works without
having to specify the "endian_check" field in ath9k_platform_data (or
a similar logic which could provide this via devicetree) as ath9k now
detects the endianness automatically. Only EEPROMs which are mangled
by some out-of-tree code still need the endian_check flag (or one can
simply remove that mangling from the out-of-tree code).
[0] http://www.spinics.net/lists/linux-wireless/msg152634.html
[1] https://marc.info/?l=linux-wireless&m=147250597503174&w=2
[2] https://marc.info/?l=linux-wireless&m=147254388611344&w=2
[3] 50719b56d9/sys/dev/ath/ath_hal/ah_eeprom_9287.c (L351)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
These patches add support for configuring ath9k based devices via
devicetree. This was tested on PCI(e) based devices. This should work
for AHB based devices as well (adding more AHB specific properties may
still be needed) as soon as the ath79 platform is ready to populate the
ath9k wmac via devicetree.
This patchset was accepted upstream, more information can be found on
the linux-wireless list:
https://www.spinics.net/lists/linux-wireless/msg155474.html
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Without setting the HSR to the selected channel, the WLAN of the UAP
Outdoor+ will exhibit high packet loss in RX.
Based-on-patch-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport upstream accepted patch which allows to override the EEPROM
mac address with one from device tree.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The patch 615-rt2x00-fix_20mhz_clk.patch fixes code introduced by
611-rt2x00-rf_vals-rt3352-xtal20.patch and makes the the platform data
property clk_is_20mhz obsolete.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Most of the lantiq devices with ralink wifi have the EEPROM stored
in big endian byte order in flash, but the driver expects the EEPROM to
be in little endian.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The ralink,mtd-eeprom device tree property doesn't require the
ralink,eeprom property to work.
Rework the error handling and user notification as well. Do not log an
error if the mtd-eeprom parameter isn't used. It could be intentional
and should not scare the user.
Check if the number of bytes read from the mtd devices matches the
requested number of bytes.
In case of an mtd read error, give a hint to the user which partition
was tried to read from.
In case everything is fine, notify the user as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Call the rt2x00lib_get_eeprom_file_name only once and from the function
where the EEPROM filename is required.
Error only out if an EEPROM file is mandatory. Use the
REQUIRE_EEPROM_FILE bit to determine if it is mandatory.
Do not set the REQUIRE_EEPROM_FILE bit while requesting an EEPROM file.
It should be (and is) set before requesting an EEPROM file.
Do not redirect users to upstream while using a function of a custom
patch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit efd9dec319.
ath10k can take a long time to probe, long enough for netifd to fail to
initialize already configured wireless devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
LEDE no longer requires all PHYs to be initialized to
create the configuration files during bootup. This patch
removes the now obsolete ath10k patch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adds the latest patches from Jes Sorensen for rtl8xxxu, which improve
rtl8732bu, rtl8192eu and rtl8188eu support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This fixes bug that could cause WARNING on every add_key/del_key call.
It also replaces WARNING with a simple message. They may still occur
e.g. on station going out of range and A-MPDU stall in the firmware.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
All these patches are in wireless-drirvers-next. There is support for
hidden SSID, few new devices and many fixes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
power save response frames can go through the old tx path, and the tid
needs to be set for sequence numbers to be assigned correctly.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit 31e5ed4152.
I've noticed some weird powersave related issues with this commit.
Revert until they've been fixed.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
To work correctly hostapd requires wireless driver to allow interfaces
removal. It was working with brcmfmac only partially. Firmware for
BCM43602 got some special hack (feature?) that allowed removing all
interfaces by disabling mbss mode. It wasn't working with BCM4366
firmware and remaining interfaces were preventing hostapd from starting
again.
Those patches add support for "interface_remove" firmware method which
works with BCM4366 firmware and they make it finally possible to use
BCM4366 & brcmfmac & multiple interfaces.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
This allows gpiolib to re-use ath9k's devicetree node as GPIO
controller.
Example:
ath9k: ath9k@0 {
#gpio-cells = <2>;
gpio-controller;
}
Now the ath9k node can be used just like any other GPIO controller:
gpios = <&ath9k 1 GPIO_ACTIVE_HIGH>;
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This enables ath9k's built-in GPIO controller for all chip versions
(instead of an explicit whitelist). This also allows us to get rid of
some duplicate code between hw.c and gpio.c because hw.c already
determines the number of GPIOs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This folds 550-ath9k_add_ar9280_gpio_chip.patch into
548-ath9k_enable_gpio_chip.patch because the former patch only extends
code which is introduced in the latter.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The PDU length of incoming LLC frames is set to the total skb payload size
in __ieee80211_data_to_8023() of net/wireless/util.c which incorrectly
includes the length of the IEEE 802.11 header.
The resulting LLC frame header has a too large PDU length, causing the
llc_fixup_skb() function of net/llc/llc_input.c to reject the incoming
skb, effectively breaking STP.
Solve the problem by properly substracting the IEEE 802.11 frame header size
from the PDU length, allowing the LLC processor to pick up the incoming
control messages.
Special thanks to Gerry Rozema for tracking down the regression and proposing
a suitable patch.
Fixes FS#24.
References:
https://bugs.lede-project.org/index.php?do=details&task_id=24
Reported-by: Gerry Rozema <gerryr@rozeware.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This makes brcmfmac compatible with mac80211 which uses dev_alloc_name
(and so returns -ENFILE on error).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
The patch 300-ath9k-force-rx_clear-when-disabling-rx.patch broke TX99 support
in ath9k. Fix the patch by only applying rx_clear if TX99 mode is not used.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Enable access to GPIO on Atheros wireless chip AR9280.
Support for 9280 is added to existing 9285/9287 subsystem
because these 3 chips differ only in number of GPIO pins.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49251
This prepares brcmfmac for better country handling and fixes BCM4360
support which was always failing with:
[ 13.249195] brcmfmac: brcmf_pcie_download_fw_nvram: FW failed to initialize
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48959
Enable access to GPIO chip and its pins for Atheros AR92xx
wireless devices. For now AR9285 and AR9287 are supported.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48881
Support default state for platform LEDs connected to ath9k device.
Now LEDs are correctly set on or off at ath9k module initialization.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48880
Enable platform-supplied WLAN LED name for ath9k device.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48879
It's not really supported yet as it still fails with:
brcmfmac: brcmf_pcie_download_fw_nvram: FW failed to initialize
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48640
llid_in_use needs to be limited to stations of the same VIF, otherwise it
will cause a NULL deref as the sta_info of non-mesh-VIFs don't have
sta->mesh set.
Steps to reproduce:
modprobe mac80211_hwsim channels=2
iw phy phy0 interface add ibss0 type ibss
iw phy phy0 interface add mesh0 type mp
iw phy phy1 interface add ibss1 type ibss
iw phy phy1 interface add mesh1 type mp
ip link set ibss0 up
ip link set mesh0 up
ip link set ibss1 up
ip link set mesh1 up
iw dev ibss0 ibss join foo 2412
iw dev ibss1 ibss join foo 2412
# Ensure that ibss0 and ibss1 are actually associated; I often need to
# leave and join the cell on ibss1 a second time.
iw dev mesh0 mesh join bar
iw dev mesh1 mesh join bar # crash
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47364
This patch fix https://lists.openwrt.org/pipermail/openwrt-devel/
2015-August/034979.html. As the peak detect calibration is set
incorrectly.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46948
So far support for multiple interface was somehow broken in brcmfmac.
Driver couldn't correctly match firmware and system interfaces resulting
in not working APs and WARNINGs. This pending patches fixes that :)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46734
We sill don't use kernel 4.2 which is required for backporting using
upstream NVRAM support patch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46724
An #ifdef for the kernel version was missing around the header of
debugfs_create_devm_seqfile() and the LINUX_BACKPORT() was also not
done.
This closes#20181
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46492
Ath10k has now a proper method of providing calibration data via
the kernel firmware API. This patch can be dropped as all boards
now use the proper method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46245
reorder some parts of the patch to remove the declaration-after-
statement warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46205
A long time ago, ath9k had issues during reset where the DMA engine
would stay active and could potentially corrupt memory.
To debug those issues, the driver would print warnings whenever they
occur.
Nowadays, these issues are gone and the primary cause of these messages
is if the MAC is stuck during reset or busy processing a long
transmission. This is fairly harmless, yet these messages continue to
worry users.
To reduce the number of bogus bug reports, turn these messages into
debug messages and count their occurence in the "reset" debugfs file.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46158
A duplicate include guard prevents inclusion of barrier.h in UML build and this prevents mac80211 from building.
This patch re-enables mac80211 hwsim and renames the include guard.
See https://lists.openwrt.org/pipermail/openwrt-devel/2015-June/033614.html for details.
Signed-off-by: Martin Tippmann <martin.tippmann@gmail.com>
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 46133
There are two important patches in this patchset: updating read pointer
quicker & rework of .get_station().
There are few more upstream patches that are p2p-related and weren't
backported in this commit.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46084
This allows e.g. BCM43602 to work out of box, without dumping a proper
MTD partition to /lib/firmware/ NVRAM file.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45931
This fixes various problems with parsing platform NVRAM. It's required
to get BCM43602 working in most cases.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45802
3.18.12 backported 61ada528dea028331e99e8ceaed87c683ad25de2 ("sched/wait:
Provide infrastructure to deal with nested blocking") from 3.19, causing
the following error on load:
[ 13.588000] compat: exports duplicate symbol woken_wake_function (owned by kernel)
Fix this by guarding it with a check for 3.18.11 or earlier instead of
3.19.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45710
Most AP devices out there do not have a properly programmed regulatory
domain code, which means they are limited to US frequencies by default.
This has been a major annoyance for a long time now. Since no fix for
the manfuacturing process seems to be forthcoming, the only sane option
seems to be to allow users to change the country code in such cases.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45252
This backports upstream commit 702131e2a393b45174be326f1dbe20b658b4f157
bcma: move PCI IRQ control function to host specific code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44969
Based on patch by Bryan Forbes <bryan@reigndropsfall.net>
Also update mt76 to update for API changes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44655
Instead of hardcoding /bin/bash, use /usr/bin/env bash - this fixes the
build on FreeBSD 10.1.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44283
This "patch to the patch" fixes a NULL pointer derefence crash in the new
intermediate software queues. The crash can be reproduced by injecting an
802.11 frame with a BSSID that does not belong to a configured vif. The
wperf tool (https://github.com/anyfi/wperf) may be convenient for doing
this.
Signed-off-by: Johan Almbladh <ja@anyfi.net>
SVN-Revision: 44220
Update the libertas driver to configure symlinks in sysfs. This enables
the driver to be handled correctly by the mac80211/netifd/hostapd scripts.
With this patch, the wireless interface is functional on Guruplug Server Plus.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 44174
This patch added stuff that is already there and if it would be needed
this would result in a compile error.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43131
This add 5GHz support for N-PHY to b43, thanks Rafał Miłecki.
b43_wflush16 was put into an extra function because it is pretty big in asm.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41900
I missed adding B43_PHY_G to .local-symbols, without this it will not
be added to autoconf.h
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41676
