'cs-gpios = <0>, <0>' is a hack in ath79 to override the incorrectly
specified maximum number of chipselects available in spi-ath79.c.
It's not needed here and must have been copied here by mistake.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.
1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
be helpful for users who may forget to do this before sysupgrade in
the initramfs.
New flash instructions:
1. Gain ssh access. Please refer to:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)
2. Check which system current u-boot is loading from:
COMMAND: `cat /proc/cmdline`
sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
if firmware=1, current system is ubi1
if firmware=0, current system is ubi0
3. Setup nvram and write the firmware:
If the current system is ubi1, please set it up so that the next time
it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
If the current system is ubi, please set it up so that the next time
it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```
4. After rebooting, the system should now boot into the openwrt initramfs.
Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.
For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:
1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```
2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Add support for EON EN25QX128A spi nor flash with no flags as it does
support SFDP parsing.
Fixes: #9442
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ramips/mt7621: xiaomi_mi-router-4a-gigabit]
add DT nodes and default package for the LEDs on Redmi AX6000
Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Without explicitly enabling sel_clk, clk_disable_unused() will disable
it when boot is done, causing CPU hang on SPI1 register access on MT7986.
Explicitly enable sel_clk to make SPI1 functional.
Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
- rtl83xx_vlan_filtering()
"struct switchdev_trans *trans" parameter was removed[1] and
"struct netlink_ext_ack *extack" was added[2].
[1]: https://www.spinics.net/lists/netdev/msg712250.html
[2]: https://www.spinics.net/lists/netdev/msg722496.html
- rtl83xx_vlan_add/del()
vlan->vid_begin and vlan->vid_end were removed and vlan->vid was
added[3].
[3]: https://www.spinics.net/lists/netdev/msg712248.html
- rtl83xx_vlan_prepare()
"port_vlan_prepare" member was removed from "dsa_switch_ops" struct
in dsa.h[4] and vlan_prepare function should be called from vlan_add
function. Also, change return type of vlan_add function to int.
[4]: https://www.spinics.net/lists/netdev/msg712252.html
- rtl83xx_port_mdb_add()
"port_mdb_prepare" member in "dsa_switch_ops" struct was removed and
preparation need to be done in the function of "port_mdb_add" member
instead. And also, int type need to be returned on "port_mdb_add"
member[5].
[5]: https://www.spinics.net/lists/netdev/msg712251.html
- rtl83xx_port_pre_bridge_flags(), rtl83xx_port_bridge_flags()
The current "port_pre_bridge_flags" member and "port_bridge_flags"
member in "dsa_switch_ops" in dsa.h has flags of
"struct switchdev_brport_flags" type instead[6], so adjust to it.
And, the changed features are passed by flags.mask[7] in
rtl83xx_port_bridge_flags(), so check it before calling function
to enable/disable fieature.
[6]: https://lore.kernel.org/lkml/20210212151600.3357121-7-olteanv@gmail.com/
[7]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e18f4c18ab5b0dd47caaf8377c2e36d66f632a8c
Suggested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[shorten final return statement of rtl83xx_port_mdb_add()]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
- 007-5.16-gpio-realtek...: upstreamed on 5.16 and backported to 5.15.3
- 708-brflood-spi.patch : upstreamed
- 709-lag-offloading.patch: upstreamed
- 713-v5.12-net-dsa-... : upstreamed and some implementations are
replaced
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The following drivers were upstreamed and available on 5.15, so drop
from OpenWrt tree.
- realtek-otto-gpio (5.13)
- realtek-rtl-spi (5.12)
- realtek-rtl-intc (5.12)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|109.3-19: Warning (reg_format): macaddr@0:reg:property has invalid length (8 bytes)
|113.3-24: Warning (reg_format): calibration@1000:reg: property has invalid length (8 bytes)
|117.3-24: Warning (reg_format): calibration@5000:reg: property has invalid length (8 bytes)
also integrate the art-nodes nodes back into the partition-subnode
and change the calibration labels to match what everyone else is
doing.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|109.3-19: Warning (reg_format): macaddr@0:reg:property has invalid length (8 bytes)
|113.3-24: Warning (reg_format): calibration@1000:reg: property has invalid length (8 bytes)
|117.3-24: Warning (reg_format): calibration@5000:reg: property has invalid length (8 bytes)
also integrate the art-nodes nodes back into the partition-subnode
and change the calibration labels to match what everyone else is
doing.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(removed mtd-cal-data property, merged art + addr nodes back into
partition)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art node back into partition-node)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art into partition node, removed stale uboot label)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Remove the caldata extraction in userspace. The board already uses
nvmem-cells since
commit e354b01baf ("ath79: calibrate all ar9344 tl-WDRxxxx with nvmem")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art-node back into partition-node)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Some carrier boards [1][2] for the Raspberry Pi CM4 that are specifically
designed to be used as routers come with secondary NICs using a Realtek
RTL8111 Gigabit Ethernet chip.
When using such a board as a router with OpenWrt, it is very helpful
when both NICs are working by default. Since the Raspberry Pi 4 and the
CM4 have plenty of disk space, it should cause no harm to include the
kmod-r8169.
[1] https://wiki.dfrobot.com/Compute_Module_4_IoT_Router_Board_Mini_SKU_DFR0767
[2] https://www.waveshare.com/wiki/CM4-DUAL-ETH-MINI
Signed-off-by: Johannes Heimansberg <git@jhe.dedyn.io>
(r8169 should pull in the necessary dependencies.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
A backported patch to the BCMA driver necessary to support the
DWL-8610AP and DIR-890L. Patch will be in upstream v6.2.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kernel 5.10.158 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.
Fixes: 6801c460b6 ("kernel: bump 5.10 to 5.10.158")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Kernel 5.15.82 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.
Fixes: 68426e54ed ("kernel: bump 5.15 to 5.15.82")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The testing kernel has been running fine for months on a rather complex
network setup, with one exception being a crash in
__xfrm_state_delete(). This crash has been fixed in kernel 5.15.82, so
let's switch the qoriq target to kernel 5.15 by default.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Compex WPQ864 contains a non standard partition table. Each partition
node should be named partition and should contain a valid reg.
Fix an extra "-" present after the reg for SBL2_1 partition.
Also add "0:" to each qcom default partition following smem naming.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The refreshed patch actually use the format of <start size start size>
instead of <start end start end>. This cause boot fail since the rootfs
can't be mounted with these wrong values.
Fix it to the correct format in each affected dts.
Fixes: #11498
Fixes: 6134ba4a34 ("ipq806x: 5.15: add boot-partitions binding to fix block warning")
Tested-by: Matt Buczko <mbuczko@hotmail.com> # Askey RT4230W
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
TP-Link CPE605-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of DDR2 RAM
- 8 MB of SPI-NOR Flash
- 23dBi high-gain directional antenna and a dedicated metal reflector
- Power, LAN, WLAN5G green LEDs
- 3x green RSSI LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface under admin account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following line:
<PARAMETER name="Password" type="string" value="<your router serial \
is here>" writable="1" encryption="1" password="1"/>
5. Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
ETxxxxxxxxxx is the serial number from the backplate label)
9. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:50 |
| WAN | label + 11 | *:5b |
| 2g | label + 2 | *:52 |
| 5g | label + 3 | *:53 |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
nvmem_cell_read return a pointer error when an error occurs. Currently
we convert the pointer error to an int while the rest of the function
return a void* and expcet an error pointer. Fix this PTR_ERR msuse
fixing compilation warning.
Fixes the following compilation warning:
net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address':
net/ethernet/eth.c:547:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion]
547 | return PTR_ERR(mac);
| ^~~~~~~~~~~~
net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address_ascii':
net/ethernet/eth.c:564:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion]
564 | return PTR_ERR(mac_ascii);
| ^~~~~~~~~~~~~~~~~~
Fixes: 7b863af180 ("kernel: move mac-address-ascii patches to generic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some Gemini devices are NAS type devices and need to ask for
DHCP IP on eth0. Some has a LAN/WAN setup. Add sensible
defaults for all known devices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch managed to sneak into v5.15 whereas it was
properly deleted for v5.10.
Fixes: 8f6e2bb178 ("bcm53xx: remove MR32's specific get_leds_dt code")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Removed a20 in description, since it
only works for a10, a13 and a31.
Also refreshed kernel config.
Fixes: #10466
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(moved fixes, refreshed, added CONFIG_DVB_USB=n)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
AddDepends/rtc has been removed in commit 3da7fe6, same here.
Fixes: 3da7fe6 ("kernel: remove useless AddDepends/rtc abstraction")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(RTC_SUPPORT - though this is implied by the TARGET_sunxi)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
enable option `CONFIG_CRYPTO_LZ4HC` to match default kernel config
this only adds the `lz4hc_compress` module, and has no effect on the
`lz4_decompress` module which already supports any flavor
Signed-off-by: Tony Butler <spudz76@gmail.com>
Reported by user: missing driver for USB; add to image definition
https://github.com/openwrt/openwrt/issues/11326Resolves: #11326
Signed-off-by: Tony Butler <spudz76@gmail.com>
Acked-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Make the patches apply cleanly again.
Fixes: 8327e0fb72 ("kernel: backport the dev_set_threaded export to 5.10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch enables USB support for the GL.iNet GL-A1300
Repair the usb driver startup phase is not loaded
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
