This adds a device tree and build options for the XG6846
switch/router to the BMIPS target.
Hardware:
- SoC: Broadcom BCM6328
- CPU: BMIPS4350 V7.5
- RAM: 64 MB DDR
- NOR Flash: 16 MB parallel (CFE and OS)
- Ethernet LAN: 4x 1Gbit
- Ethernet WAN: 2x 1Gbit, fiber and TP
- Buttons: reset
- LEDs: 7 or 8, power and USB LEDs are GPIO-based, the
LAN LEDs are controlled by the Marvell DSA Switch.
- USB: on some versions
- UART: yes
The device ODM (original device manufacturer) is XAVi
http://www.xavi.com.tw/
It is possible to boot the initramfs version
openwrt-bmips-bcm6328-inteno_xg6846-initramfs.elf from
CFE by interrupting the boot on the UART console and downloading
it from a TFTP server e.g.:
CFE> r 192.168.1.2:openwrt-bmips-bcm6328-inteno_xg6846-initramfs.elf
Installation to target flash is not possible using CFE because
the image becomes too big for the CFE version found in these
devices. A separate U-Boot two-stage solution exists for
actually booting the device.
This device is called a "managed ethernet switch" by the vendor
and "media converter" or "fiber modem" by some of the ISPs
using it: the main purpose is to convert fiber connections to
ethernet, most devices just act as switches bridging the
fiber SFP to ethernet TP.
The device has a Marvell MV88E6352 DSA switch managed by
a BCM6328 BMIPS SoC.
This port makes it possible to use the XG6846 to grab an IP
number from the fiber connection and use all four LAN
connections out, turning it into a proper router.
This support is based mostly on the observations by the people on
the forum thread "Help with Inteno XG6846" where users NPeca75,
mrhaav, systemcrash and csom helped out to reverse engineer the
device. Then I made it work on the BMIPS target, figured out
the two-level switch hierarchy and settings.
Link: https://forum.openwrt.org/t/help-with-inteno-xg6846/68276/14
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Innacomm W3400V6 is an xDSL B/G wireless router based on Broadcom
BCM6328 SoC.
SoC: Broadcom BCM6328
CPU: BMIPS4350 V8.0, 320 MHz, 1 core
Flash: SPI-NOR 8MB, MX25L6406E
RAM: 64 MB
Ethernet: 4x 10/100 Mbps
Switch: Integrated
Wireless: 802.11b/g, BCM4312
LEDs/Buttons: 9x / 2x
Flash instruction, web UI:
1. Set a static IP on your computer compatible with 192.168.1.1, i.e
192.168.1.100.
2. Connect the ethernet cable from your computer to the router.
3. Make sure the router is powered off.
4. Press the reset button, don't release it yet!
5. While pressing reset, power on the router.
6. Wait 10 seconds or more.
Note: The power LED is red at first then turns to solid green when
ready.
7. Release the reset button.
8. Browse to 192.168.1.1
9. Select .bin file.
10. Upgrade the image.
11. Wait for it to reboot.
Signed-off-by: Sieng-Piaw Liew <liew.s.piaw@gmail.com>
[Fix cfe nvmem-layout and pinctrl_leds indentation]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Arcadyan AR7516, AKA Orange Bright Box or EE Bright Box 1, is a wifi
fast ethernet router, 2.4 GHz single band with two internal antennas. It
comes with a horizontal stand black shiny casing.
Newer Bright Box 1 model stands vertically, and comes with a totally
different board inside, not compatible with this firmware.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 V7.5 @ 320Mhz
- RAM: 64 MB DDR2
- Flash: 8 MB SPI NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: Broadcom BCM43227 802.11bgn (onboard)
- USB: 1x 2.0
- ADSL: yes, unsupported
- Buttons: 2x
- LEDs: 9x, power LED is hardware controlled
- UART: yes
Installation in two steps, new CFE bootloader and firmware:
Install new CFE:
1. Power off the router and press the RESET button
2. Power on the router and wait some seconds
3. Release the RESET button
3. Browse to http://192.168.1.1, this web interface will offer both
firmware (“Software”) upgrade and bootloader upgrade; be sure to
use the bootloader section of the upload form.
4. Upload the new CFE (availabe at the wiki page)
5. Wait about a minute for flashing to finish and reboot into the new bootloader.
Install OpenWrt via new CFE web UI:
1. After installing the new CFE, visit http://192.168.1.1
2. Upload the Openwrt cfe firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The NuCom R5010UNv2 is a wifi fast ethernet router, 2.4 GHz single band
with two external antennas.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 V7.5 @ 320Mhz
- RAM: 64 MB DDR2
- Flash: 16 MB SPI NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: Broadcom BCM43217 802.11bgn (onboard)
- USB: 1x 2.0
- Buttons: 2x
- ADSL: yes, unsupported
- LEDs: 7x
- UART: yes
Installation via CFE web UI:
1. Power off the router and press the RESET button
2. Power on the router and wait 12 or more seconds
3. Release the RESET button
4. Browse to http://192.168.1.1 and upload the Openwrt cfe firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Sercomm AD1018 is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB (v1) / 128 MB (v2) DDR
- Flash: 128 MB NAND
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM43217 802.11bgn
- USB: 1x 2.0
- Buttons: 3x (reset)
- LEDs: yes
- UART: yes
Installation via OEM web UI:
1. Use the admin credentials to login via web UI
2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
3. Press "Update Firmware" button and wait some minutes until it finish
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Comtrend AR-5381u is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB DDR
- Flash: 16 MB SPI NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM43225 802.11bgn
- USB: 1x 2.0
- Buttons: 1x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
BMIPS is a generic arch that can be used for multiple Broadcom SoCs, each one
with its own specific drivers, so instead of having a huge kernel supporting
all of them, let's switch to a subtarget per SoC like other OpenWrt targets.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
