Commit Graph

21213 Commits

Author SHA1 Message Date
Christoph Krapp
8ad674e90b ar71xx: change u-boot-env to read-write for ZyXEL NBG6616
As the ath79 port of this device uses a combined kernel + root
partition the uboot bootcmd variable needs to be changed. As using
cli/luci is more convenient than opening up the case and using a uart
connection, lets unlock the uboot-env partition for write access.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
(cherry picked from commit 982c1f6e42)
2020-08-10 00:07:36 +02:00
Tobias Welz
d40ce8b32d ramips: correct WizFi630S pin mappings
WizFi630S had some pins changed in the release version of the board.
The run led, wps button and a slide switch where affected.
This patch is correcting this.
i2c is removed as it is sharing a pin with the run (system) led.
uart2 is enabled as it is also enabled in the OEM firmware.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
(backported from commit d0b229f553)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 16:36:32 +02:00
Tobias Welz
d1985a1be6 ramips: enable flashing WizFi630S via OEM firmware
WIZnet WizFi630s board name is written slightly different it its OEM
OpenWrt firmware. This causes an incompatibility warning during flashing
with sysupgrade. This patch is adding the vendor board name to the
supported devices list to avoid this warning. For initial flashing you
can use sysupgrade via command line or luci beside of TFTP.
Do not keep the OEM configuration during sysupgrade.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
(cherry picked from commit 816973f42a)
2020-08-08 16:36:24 +02:00
Tobias Welz
4212b6a01e ramips: remove doublet entry in WizFi630S dts file
&wmac entry in WIZnet WizFi630S dts file was existing two times.
This is removing one of them.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
(cherry picked from commit b735bbcb18)
2020-08-08 16:36:15 +02:00
Tobias Welz
a81c459d99 ramips: disable unused phy ports of WizFi630S
WIZnet WizFi630S is using only 3 of the phy ports. The unused phy ports
draw unnecessarily power. This is disabling the unused phy ports.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
(cherry picked from commit 36d4c2272e)
2020-08-08 16:36:08 +02:00
Josua Mayer
9d2dea8302 mvebu: fix LAN/WAN port assignment on ClearFog Base/Pro
The comments in code already describe the intended lan / wan assignment:
lan: switch
wan: standalone ethernet and sfp

Update the interface handles to match the comments, as observed with
OpenWRT-19.07-rc2 on a Clearfog Pro Rev 2.0.

This also matches the effective assignment on master, while the actual
interface names (ethX) are different due to the reassignment in
06_set_iface_mac, which is included in 19.07 but was dropped for master.

Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
[extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-07 17:13:40 +02:00
Sungbo Eo
de1693e56f ar71xx: restore support for boot console with arbitrary baud rates
Commit 1bfbf2de6d ("ar71xx: serial: core: add support for boot console
with arbitrary baud rates") added support for arbitrary baud rates which
enabled 250000 baud rate for Yun. But the patch was not ported to kernel
4.9, and since then the kernel set its baud rate to 9600. This commit ports
the patch to kernel 4.14, thereby restoring the serial console of Yun.

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit c90db26e05)
2020-08-02 18:16:00 +02:00
Adrian Schmutzler
1b3aca9142 ath79: restore support for boot console with arbitrary baud rates
The Arduino Yun uses a baud rate of 250000 by default. The serial is
going over the Atmel ATmega and is used to connect to this chip.
Without this patch Linux wants to switch the console to 9600 Baud.

With this patch Linux will use the configured baud rate and not a
default one specified in uart_register_driver().

This has been added for ath79 4.19 and 5.4 in master as part of
fc59b2f79b ("ath79: add support for Arduino Yun"), this backports
it separately to 4.14.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-02 18:15:45 +02:00
Sungbo Eo
f6acabcbdc ar71xx: enable ethernet LED of Arduino Yun
Commit 05d73a2a73 enabled GPIO on ethernet LED, but proper LED setup was
not added then. This commit fixes it by reverting the change on the LED.

Fixes: 05d73a2a73 ("ar71xx: Arduino Yun board 'WLAN RST' button support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit a5e404d192)
2020-08-02 16:36:22 +02:00
Sungbo Eo
f17174e843 ar71xx: fix sysupgrade for Arduino Yun
Commit bb46b635df changed its partition scheme, but sysupgrade image
validation still uses the old format. This commit fixes it so that
force flag is not needed for sysupgrade.

Fixes: bb46b635df ("ar71xx: move Arduino Yun to generic building code")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 58dc1d0637)
2020-08-02 16:36:07 +02:00
Sungbo Eo
f3c0eab9c7 Revert "ar71xx: fix Arduino Yun enabling of level shifters outputs"
This reverts commit 077253dd66.

The output enable pins should be disabled by default, and only enabled when
used. Otherwise unwanted conflicts might occur between MCU and SoC pins.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 43896dc0b0)
2020-08-02 16:35:54 +02:00
Alexey Dobrovolsky
2f756b39ed ramips: add kmod-usb-dwc2 to ZyXEL Keenetic image
ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should
be in the default image for this device.

Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(backported from commit 0a182fcba6)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-02 13:42:49 +02:00
Alexey Dobrovolsky
06c6a3dd70 ramips: remove patches for USB-dwc2
In FS#2738 we can see that patch first introduced in
e8ebcff ("ramips: add a explicit reset to dwc2")
breaks USB functionality since 18.06. Thus, this patch should be removed.

Removed:
- 0032-USB-dwc2-add-device_reset.patch

Fixes: FS#2738
Fixes: FS#2964

Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
(cherry picked from commit ab841b4393)
2020-08-02 13:40:07 +02:00
David Woodhouse
bf58bfb90e mediatek: mt7623: fix sysupgrade from vendor OpenWrt on UniElec U7623
This board ships with an ancient 14.07-based OpenWrt using block2mtd, and
the MBR partition table contains nonsense.

It is possible to sysupgrade to an upstream OpenWrt image, but the
legacy layout of the OpenWrt images start at 0xA00 in the eMMC, with
a raw uImage. The legacy OpenWrt image doesn't "own" the beginning
of the device, including the MBR and U-Boot.

This means that when a user upgrades to upstream OpenWrt, it doesn't
boot because it can't find the right partitions. So hard-code them on
the kernel's command line using CONFIG_CMDLINE_PARTITION (for block).

Additionally, the vendor firmware doesn't cope with images larger than
about 36MiB, because it only overwrites the contents of its "firmware"
MTD partition. The current layout of the legacy image wastes a lot of
space, allowing over 32MiB for the kernel and another 10MiB for the FAT
recovery file system which is only created as 3MiB. So pull those in
to allow 4¾ MiB for the kernel, 3MiB for recovery, and then we have over
20MiB for the root file system.

This doesn't affect the new images which ship with a full eMMC image
including a different MBR layout and a partition for U-Boot, because
our modern U-Boot can actually pass the command line to the kernel, and
the built-in one doesn't get used anyway.

Tested by upgrading from vendor OpenWrt to the current legacy image,
from legacy to itself, to the previous legacy layout, and then to
finally the full-system image.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
(cherry picked from commit 6eb63019af)
2020-07-30 11:50:07 +08:00
David Woodhouse
2147c33e40 mediatek: mt7623: add explicit console= to U7623 kernel
The bootloader for legacy builds can't set it, so we end up unable to
log in on the serial port.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
(cherry picked from commit ea9ef8c945)
2020-07-30 11:50:07 +08:00
Adrian Schmutzler
a2c9fc9ff0 ath79: correctly define WiFi switch for TL-WR841ND v8
The TL-WR841ND v8 feature a WiFi switch instead of a button.
This adds the corresponding input-type to prevent booting into
failsafe regularly.

This has been defined correctly in ar71xx, but was overlooked
when migrating to ath79. In contrast, the TL-WR842ND v2, which
has the key set up as switch in ar71xx, actually has a button.
The TL-MR3420 v2 has a button as well and is set up correctly
for both targets. (Information based on TP-Link user guide)

Note:

While looking into this, I found that support PR for TL-MR3420 v2
switched reset button to ACTIVE_HIGH. However, the other two
device still use ACTIVE_LOW. This seems strange, but I cannot
verify it lacking the affected devices.

Fixes: FS#2733
Fixes: 9601d94138 ("add support for TP-Link TL-WR841N/ND v8")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 5e86877f36)
2020-07-23 17:40:23 +02:00
Adrian Schmutzler
7022f1eb13 bcm47xx: fix switch setup for Linksys WRT610N v2
WRT610N V2 is not detected by the initial network configuration script.
The switch remains unconfigured and wlan/lan vlans are not created.

This adds the correct setup for the device.

Fixes: FS#1869

Suggested-by: Alessandro Radicati
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a2fee73e27)
2020-07-23 17:40:00 +02:00
Dustin Gathmann
a785aed70e lantiq/xrx200: make WLAN button responsive on Fritzbox 7360 & 7362
Pressing the 'WLAN' button should enable/disable wireless activity.
Currently, the button is mapped to the KEY_WLAN, which will not
have this effect.
This patch changes the mapping of the WLAN button, so a button
press will emit an action for the 'rfkill' key instead of 'wlan'.
Apparently, this is what stock OpenWRT expects.

This fix is analogous to the preceding patch for Fritzbox 3370.

Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
(cherry picked from commit d5a148f5c8)
2020-07-23 17:39:42 +02:00
Dustin Gathmann
4a9d6320af lantiq/xrx200: fix WLAN button actions for Fritzbox 3370
The WLAN button actions are reversed, i.e. pressing the button emits a
'released' action, and vice versa.
This can easily be checked by adding
logger -t button_action "$BUTTON $ACTION"
as the second line of /etc/rc.button/rfkill, and using logread to read
the events (assuming the preceding patch has been applied).
Defining the GPIO as ACTIVE_LOW corrects this behavior.

Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
(cherry picked from commit 0ee30adb46)
2020-07-23 17:39:35 +02:00
Dustin Gathmann
284cd7d18e lantiq/xrx200: make WLAN button responsive on Fritzbox 3370
Pressing the 'WLAN' button should enable/disable wireless activity.
However, on the Fritzbox 3370 this doesn't have an effect.
This patch changes the mapping of the physical WLAN button, so a button
press will emit an action for the 'rfkill' key instead of 'wlan'.
Apparently, this is what stock OpenWRT expects, and also what is
implemented for most other devices.

Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
(cherry picked from commit a53bf63756)
2020-07-23 17:39:29 +02:00
John Crispin
8c19171255 ipq40xx: fix ethernet vlan double tagging
As the the SoC uses implicit vlan tagging for dual MAC support, the
offload feature breaks when using double tagging.

This is backport of 9da2b56760 from trunk.
As the layout of the files has changed a cherry-pick was not possible.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: John Crispin <john@phrozen.org>
2020-07-14 18:36:19 +02:00
Sungbo Eo
8ea6be1510 kirkwood: support for button in Pogoplug V4
Pogoplug V4 has a reset button on a GPIO pin.
To use it, kmod-gpio-button-hotplug package needs to be installed.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 91472dc2ce)
2020-07-10 13:55:54 +02:00
Luca Olivetti
de75d6ecfa lantiq: dts: Move the &usb_vbus nodes out of &gpio
Move the USB VBUS regulator nodes out of the GPIO controller node. This
fixes a problem where the "regulator-fixed" driver wasn't probed for
these regulators because the GPIO driver doesn't scan the child-nodes
and based on the dt-bindings documentation it's not supposed to.

This fixed the following error reported by Luca Olivetti:
  ...
  dwc2 1e101000.usb: DWC OTG Controller
  dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
  dwc2 1e101000.usb: irq 62, io mem 0x1e101000
  dwc2 1e101000.usb: startup error -517
  dwc2 1e101000.usb: USB bus 1 deregistered
  dwc2 1e101000.usb: dwc2_hcd_init() FAILED, returning -517

Fixes: FS#1634
Cc: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[backported from 982468de35]
Signed-off-by: Luca Olivetti <luca@ventoso.org>
2020-07-10 13:55:21 +02:00
Hauke Mehrtens
2d14da2c7d ar71xx: Fix mikrotik NAND compile problem
This fixes the following compile error:
drivers/mtd/nand/rb91x_nand.c: In function 'rb91x_nand_remove':
drivers/mtd/nand/rb91x_nand.c:445:16: error: 'rbni' undeclared (first use in this function)
  nand_release(&rbni->chip);

Fixes: 9cad70044f ("kernel: fix nand_release() usage.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 66e04abbb6)
2020-07-07 23:43:26 +02:00
Hauke Mehrtens
673e7944bb ar71xx: Fix mikrotik NAND compile problem
There is one closing bracket too much.

Fixes: 9cad70044f ("kernel: fix nand_release() usage.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 014d3f593a)
2020-07-06 00:12:04 +02:00
Petr Štetiar
73e0ea1ea9 armvirt,x86: fix build breakage of crypto ccp module
Upstream in commit f9f8f0c24203 ("crypto: ccp -- don't "select"
CONFIG_DMADEVICES") removed dependency on CONFIG_DMADEVICES symbol which
leads to build breakage of ccp crypto module, so fix this by adding that
symbol back in the kernel config.

Fixes: f4985a22ca ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 472b8fc91b)
2020-07-05 13:33:31 +02:00
Hauke Mehrtens
9cad70044f kernel: fix nand_release() usage.
nand_release() takes nand_chip since commit 5bcfcbfc4019 ("mtd: rawnand:
Pass a nand_chip object to nand_release()")

Fixes: f4985a22ca ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 21:04:11 +02:00
Hauke Mehrtens
f4985a22ca kernel: Update kernel 4.14 to version 4.14.187
Fixes:
- CVE-2020-10757

Run tested: ath79, ipq40xx
Build tested: ath79, ipq40xx

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 19:22:23 +02:00
Adrian Schmutzler
8293c8ed46 ath79: do not build TP-Link tiny images by default
For quite some time, the tiny (4M flash) TP-Link sysupgrade and
factory images cannot be built anymore by the buildbots, just
the initramfs-kernel.bin files are still there.

Disable these images for the buildbots and don't waste build
resources.

Note that these devices still build fine with default settings,
just not with the additional packages and config symbols for
the buildbots.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 14:37:22 +02:00
Adrian Schmutzler
670eeb7888 mediatek: fix IPv4-only corner case and commit in 99-net-ps
The uci config section network.globals set up in /bin/config_generate
will only be created if /proc/sys/net/ipv6 exists.

Correspondingly, lacking IPv6 support, the command
uci set network.globals.packet_steering=1
will fail with "uci: Invalid argument" as the network.globals config
has not been set up.

Fix that by adding the setup there as well.

While at it, limit the uci commit to the network config file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 636b62e8e2)
2020-06-28 14:34:35 +02:00
Daniel González Cabanelas
9c58f5d4ff bcm63xx: DGND3700v1: fix port order
Fix the switch LAN labels for the DGND3700v1/DGND3800B router,
the order is reversed.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[cut out of bigger patch, adjust commit title/message accordingly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 583b3e4025)
2020-06-28 14:32:42 +02:00
INAGAKI Hiroshi
ebefdf61ed ramips: increase SPI frequency for ELECOM WRC-GST devices
Increase the SPI frequency for ELECOM WRC-1900GST and WRC-2533GST
to 40 MHz by updating the common DTSI file.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[WRC-1900GST]
Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit b5ae70d053)
2020-06-28 14:31:51 +02:00
Jose Olivera
6b042217d7 mvebu: fix default EU regdomain for Linksys WRT AC devices
The mwlwifi driver sets the default country code for EU (fi-
rmware region code 0x30) certified devices to FR (France),
not DE (Germany). Whilst this is a trivial fix, novice users
may not know how mwlwifi negatively reacts to a non-matching
country code and may leave the setting alone. Especially si-
nce it is under the advanced settings section in LuCI.

Relevant mwlwifi driver code:
0a550312dd

The mwlwifi driver readme states "Please don't change country
code and let mwlwifi set it for you." However, OpenWrt's current
behaviour does not adhere to this with its default, 'just flashed
from factory' setting for EU devices.

Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d0e8b8310f)
2020-06-28 14:29:41 +02:00
Adrian Schmutzler
b40e6bc55f ath79: drop and consolidate redundant chosen/bootargs
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.

The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi

While this is a cosmetic change, backporting it to 19.07 will be a
major help for anyone doing backports of device support. Without it,
every backporter would have to remember to manually add the chosen node
to the device's DTS.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 635f111148)
2020-06-28 14:24:59 +02:00
Adrian Schmutzler
153392e209 ath79: add support for TP-Link TL-WA801ND v3/v4
This ports support for these devices from ar71xx.

Specification:

- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: v3: 560 MHz, v4: 650 MHz
- Flash: 4096 KiB
- RAM: 32 MiB
- Ethernet: 1 port @ 100M
- Wireless: SoC-integrated: QCA9533 2.4GHz 802.11bgn

In contrast to the implementation in ar71xx (reset and WiFi button),
the device actually features reset and WPS buttons.

Flashing instructions:

Upload the ...-factory.bin file via OEM web interface.

TFTP Recovery:

1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to
   wa801ndv3_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
   the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

TFTP recovery has only been tested with v3, and the Wiki states
that the procedure won't work for v4, which cannot be verified
or falsified at the moment.

Tested by Tim Ward (see forum):
https://forum.openwrt.org/t/ath79-support-for-tp-link-tl-wa901nd-v3-v4-v5/61246/13

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 9a477b833a)
2020-06-21 21:34:09 +02:00
Daniel González Cabanelas
18cf2383b6 bcm63xx: a226m-fwb: fix linux partition offset
The Pirelli A226M-FWB has a wrong linux partition offset, caused
by a copy-paste error. As of result of this, OpenWrt is currently
broken in this unit.

Fix it.

While at it, also use generic node names and fix the addresses
there as well.

Fixes: a27d59bb42 ("brcm63xx: switch to new partition layout
specification")

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[also fix/update node names, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d64d5ed142)
2020-06-15 21:00:34 +02:00
Sven Eckelmann
b515edb775 ipq40xx: essedma: Disable TCP segmentation offload for IPv6
It was noticed that the the whole MAC can hang when transferring data from
one ar40xx port (WAN ports) to the CPU and from the CPU back to another
ar40xx port (LAN ports). The CPU was doing only NATing in that process.

Usually, the problem first starts with a simple data corruption:

  $ wget https://cdimage.debian.org/debian-cd/current/amd64/iso-cd/debian-10.4.0-amd64-netinst.iso -O /dev/null
  ...
  Connecting to saimei.ftp.acc.umu.se (saimei.ftp.acc.umu.se)|2001:6b0:19::138|:443... connected.
  ...
  Read  error at byte 48807936/352321536 (Decryption has failed.). Retrying.

But after a short while, the whole MAC will stop to react. No traffic can
be transported anymore from the CPU port from/to the AR40xx PHY/switch and
the MAC has to be resetted.

The whole problem can be avoided by disabling IPv6 TSO for this ethernet
MAC driver.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: John Crispin <john@phrozen.org>
(backported from commit 6785695056, with
updated commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-06-13 17:39:17 +02:00
Christian Lamparter
f7f15f8033 ath79: wndr3700 series: fix wifi range & throughput
This patch adds ar71xx's GPIO setup for the 2.4GHz and 5GHz antennae
demultiplexer:

| 158         /* 2.4 GHz uses the first fixed antenna group (1, 0, 1, 0) */
| 159         ap9x_pci_setup_wmac_gpio(0, (0xf << 6), (0xa << 6));
| 160
| 161         /* 5 GHz uses the second fixed antenna group (0, 1, 1, 0) */
| 162         ap9x_pci_setup_wmac_gpio(1, (0xf << 6), (0x6 << 6));

This should restore the range and throughput of the 2.4GHz radio
on all the derived wndr3700 variants and versions with the AR7161 SoC.
A special case is the 5GHz radio. The original wndr3700(v1) will
benefit from this change. However the wndr3700v2 and later revisions
were unaffected by the missing bits, as there is no demultiplexer
present in the later designs.

This patch uses gpio-hogs within the device-tree for all
wndr3700/wndr3800/wndrmac variants.

Notes:

Based on the PCB pictures, the WNDR3700(v1) really had eight
independent antennae. Four antennae for each radio and all of
those were printed on the circut board.

The WNDR3700v2 and later have just six antennae. Four of those
are printed on the circuit board and serve the 2.4GHz radio.
Whereas the remaining two are special 5GHz Rayspan Patch Antennae
which are directly connected to the 5GHz radio.

Hannu Nyman dug pretty deep and unearthed a treasure of information
regarding the history of how these values came to be in the OpenWrt
archives: <https://dev.archive.openwrt.org/ticket/6533.html>.

Mark Mentovai came across the fixed antenna group when he was looking
into the driver:

    fixed_antenna_group 1, (0, 1, 0, 1)
    fixed_antenna_group 2, (0, 1, 1, 0)
    fixed_antenna_group 3, (1, 0, 0, 1)
    fixed_antenna_group 4, (1, 0, 1, 0)

Fixes: FS#3088

Reported-by: Luca Bensi
Reported-by: Maciej Mazur
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Debugged-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 61307544d1)
2020-06-09 22:46:21 +02:00
Daniel Golle
fa72f2646a oxnas: build with 8021Q VLAN support
CONFIG_VLAN_8021Q was explicitely disabled in oxnas kernel config.
Don't do that, so VLANs can be used on the target.

Fixes: dcc34574ef ("oxnas: bring in new oxnas target")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fd0cc72d9c)
2020-06-09 16:53:51 +01:00
Lech Perczak
e752fc1ff9 ath79: add support for TP-Link TL-WR802N V1 and V2
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of Flash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)

Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to web interface:
  [V1] http://192.168.0.1
  [V2] http://192.168.0.254
  Default user is "admin" & password is "admin".
  On V2, there is no DHCP server running by default, so remember to set
  IP manually.
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware:
  [V1] "*.factory.bin"
  [V2] "*.factory-us.bin" or  "*.factory-eu.bin" for eu model
  Web interface may complain if filename is too long. In such case,
  rename .bin to something shorter.
- Click upgrade

Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
      Serial Configuration 115200 8n1

- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
    (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
    (e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
    (e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
    (e.g bootm 0x9f020000)

Notes:

When porting from ar71xx target to ath79, I found out that on V2,
reset button is on GPIO12 and active low, instead of GPIO11 and
active high. By cross-flashing V1 firmware to V2, I confirmed
the same is true for V1.
Also according to manual of V1, this one also has green
LED instead of blue - both of those issues were fixed accordingly.

The MAC address assignment has been checked with OEM firmware.

Installation manual based on ar71xx support by Thomas Roberts

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit message, add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 7e513136c6)
2020-06-03 15:29:37 +02:00
Roger Pueyo Centelles
6488d2f7cc ath79: update WA/XC devices UBNT_VERSION to 8.5.3
Ubiquiti WA devices with newer hw version 2011K require UBNT_VERSION
to be at least 8.5.3, otherwise the image is rejected:

   New ver: WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3
   Versions: New(525568) 8.5.0, Required(525571) 8.5.3
   Invalid version 'WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3'

For consistency, also increase version number for XC devices.

Tested-by: Pedro <pedrowrt@cas.cat>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit 95caa3436d)
2020-06-03 15:29:20 +02:00
Samantha Collard
fb79e5d9fe ipq806x: EA8500 fix boot partition detection
Remove extraneous code that disabled boot partition detection.

Fixes: b3770eaca3 ("mtd: base-files: Unify dual-firmware devices (Linksys)")
Signed-off-by: Samantha Collard <sammyrc34@gmail.com>
(cherry picked from commit 0f910a8c4c)
2020-06-03 15:29:03 +02:00
Adrian Schmutzler
e36bdd5dc5 ath79: fix LEDs for GL.inet GL-AR150
Since the wireless LED was used for boot and set up with a DT
trigger, the WiFi indication hasn't worked on ath79 at all.

In addition, a look into the manual revealed that the OEM
configuration is as follows:

LED 1 (green): power
LED 2 (green): configurable
LED 3 (red): wireless

So, let's just keep the WiFi trigger and convert the rest to its
"intended" use.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 705fe43522)
2020-06-03 15:28:50 +02:00
Lech Perczak
21454a772b ar71xx: fix reset key for TP-Link TL-WR802N V1/V2
During porting support for this router to ath79 target
it was discovered that GPIO mapping was incorrect (GPIO11 active high).
Correct mapping for both V1 and V2 is GPIO12 active low.

Default configuration from GPL source for V2 explicitly states this, and
this was confirmed experimentally on ath79 by looking on
/sys/kernel/debug/gpio. Correctness of this was also validated for V1 by
cross-flashing vendor firmware for V1 on V2 hardware, in which reset
button also worked.

Fix it.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit f841e70640)
2020-06-01 16:58:06 +02:00
John Crispin
a32b0ec4cf generic: fix flow table hw offload
Make the driver work with recent upstream changes.

Fixes: FS#2632
Ref: https://github.com/openwrt/openwrt/pull/2815
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 6786dc26a2)
2020-06-01 11:42:12 +02:00
David Bauer
9cafcbe0bd ar71xx: correct button type for TL-MR3020 mode slider
The TP-Link TL-MR3020 has a three-state mode slider which was previously
integrated as a button (EV_KEY). This led to spurious activations of
failsafe mode.

Set the type for the button to switch (EV_SW), to avoid unintended
activations of failsafe mode.

Related: commit 27f3f493de ("gpio-button-hotplug: unify polled and
interrupt code")

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b017a016cc)
2020-05-31 15:54:52 +02:00
Adrian Schmutzler
2bd1cf92e9 ar71xx: fix splitting firmware partition for TL-WR902AC v1
The -O option for the tplink-v1-header was missing for the TP-Link
TL-WR902AC v1, while safeloader and MTDPARTS where set up with a
single firmware partition.

This led to bootloops after using sysupgrade.

Fixes: FS#3118

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a7b07f8ba8)
2020-05-30 00:36:59 +02:00
Petr Štetiar
498f1f4f5d ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control by default
Looking at the current upstream driver implementation, it seems like the
TX/RX flow control is enabled only if the flow control pause option is
resolved from the device/link partner advertisements (or otherwise set).

On the other hand, our current in-tree driver force enables TX/RX
flow control by default, thus possibly leading to TX timeouts if the
other end sends pause frames (which are not properly handled?):

 WARNING: CPU: 3 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x1ac/0x324
 NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out

Disabling the flow control on PORT 5 MAC seems to fix this issues as the
pause frames are then filtered out. While at it, I'm removing the if
condition completely as suggested, since this code is run only on mt7621
SoC, so there is no need to check for the silicon revisions.

Ref: https://lists.openwrt.org/pipermail/openwrt-devel/2017-November/009882.html
Ref: https://forum.openwrt.org/t/mtk-soc-eth-watchdog-timeout-after-r11573/50000/12
Suggested-by: Felix Fietkau <nbd@nbd.name>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c8f8e59816)
2020-05-26 10:07:05 +01:00
Jo-Philipp Wich
bc0c2db2a3 brcm47xx: disable Netgear WNR2000 v2 by default
Disable the Netgear WNR2000 v2 image by default as the device has
insufficient flash space for release build images.

Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/72
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
[drop change on netgear-wnr3500l-v1-na]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-24 14:42:33 +02:00
Adrian Schmutzler
6a89098935 ath79: add support for TP-Link TL-WA901ND v4 and v5
This ports support for the TL-WA901ND v4 and v5 from ar71xx to ath79.
They are similar to the TP9343-based TL-WR940N v3/v4 and TL-WR941ND v6.

Specifications:
  SoC: TP9343
  Flash/RAM: 4/32 MiB
  CPU: 750 MHz
  WiFi: 2.4 GHz b/g/n
  Ethernet: 1 port (100M)

Flashing instructions:
  Upload the factory image via the vendor firmware upgrade option.

Flash instruction (TFTP):
  1. Set PC to fixed ip address 192.168.0.66
  2. Download *-factory.bin image and rename it to * (see below)
  3. Start a tftp server with the image file in its root directory
  4. Turn off the router
  5. Press and hold Reset button
  6. Turn on router with the reset button pressed and wait ~15 seconds
  7. Release the reset button and after a short time
     the firmware should be transferred from the tftp server
  8. Wait ~30 second to complete recovery.

  * The image name for TFTP recovery is wa901ndv4_tp_recovery.bin for
  both variants.

In ar71xx, a MAC address with offset 1 was used for ethernet port.
That's probably wrong, but this commit sticks to it until we know
the correct value.

Like in ar71xx, this builds the default factory.bin with EU country
code.

Thanks to Leonardo Weiss for testing on the v5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 4a61a88f90)
2020-05-20 21:06:48 +02:00