If the dnsmasq process forks to handle TCP connections, it closes the ubus
context. But instead of changing the daemon wide pointer to NULL, only the
local variable was adjusted - and this portion of the code was even dropped
(dead store) by some optimizing compilers.
It makes more sense to change the daemon->ubus pointer because various
functions are already checking it for NULL. It is also the behavior which
ubus_destroy() implements.
Fixes: d8b33dad0b ("dnsmasq: add support for monitoring and modifying dns lookup results via ubus")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This is not activated by default and must be explicitly enabled via ubus
It supports reporting log messages and netlink packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The new rewritten ipcalc.sh understands 3 notations:
ipaddr/prefix ...
ipaddr/dotted-netmask ...
ipaddr dotted-netmask ...
meaning that the previous 4th non-standard notation of "ipaddr prefix"
will be dropped, alas that's the notation that dnsmasq currently uses.
This change has us using the first notation which is the most common.
This behavior came in as
eda27e8382
a long time ago.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
eee02ccca8c8 device: add support to configure eee
bb28f6a291d9 wireless: fix sign comparison warning
35facc8306f5 wireless: fix premature removal of hotplug devices due to down state
Signed-off-by: Felix Fietkau <nbd@nbd.name>
841b05fbb91e system-linux: fix compilation error if IFLA_DSA_MASTER is not supported
5c9ecc1ff74f system-linux: make system_if_get_master_ifindex static
2dc7f450f3a2 system-linux: add option to configure DSA conduit device
838f815db5ef system-linux: add support for configurable GRO option
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently for 802.1s only, for wifi 2.4GHz in g/n mode, 40MHz is never
permitted.
This is probably due to the complexity of setting periodic check for the
intolerant bit. When noscan option is set, we ignore the presence of the
intoleran bit in near AP, so we can enable 40MHz and ignore any complex
logic for checking.
Fixes: #13112
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Also channel 7 for 2.4GHz can be set to HT40PLUS. Permit this and add it
to the list of the channels.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
noscan option for mesh was broken and actually never applied.
This is caused by a typo where ssid->noscan value is check instead of
conf->noscan resulting in the logic swapped and broken.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
383753dd65ae device/bridge: support passing extra vlans in the device_set_state call
b6e75eafc1af device: send notifications for device events via ubus
cab415c7aefd bridge: add auth-required bridge members with auth_status=0 if vlan is enabled
827a02f0343c bridge: add support for configuring vlans for auth=1,auth_status=false
40ed7363caf2 device: fix build error on 32 bit systems
516ab774cc16 system-linux: fix race condition on bringing up wireless devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
4101dd4 fw4: perform strict validation of zone and set names
a923c88 fw4: pass zone to templates whenever possible
597dc90 fw4: add support for zone log_limit
1874050 fw4: add log_limit to rules and redirects
19a8caf ruleset: dispatch ct states using verdict map
a5553da ruleset: reduce ksoftirqd load by refering to looopback by numeric id
de3483c tests: adjust zone log limit testcases
7392792 ruleset: do not emit redundant drop invalid rules
698a533 ruleset: apply egress MSS fixup later to apply final MTU before wire
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It's already pulled in from /etc/rc.common.
Fixes: #13758
Fixes: 6b23836071 ("package: avoid the use of eval to parse ipcalc.sh output")
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Upgrading wpa_supplicant from 2.9 to 2.10 breaks broadcom-wl/ath11k
based adapters. The reason for it is hostapd tries to install additional
IEs for scanning while the driver does not support this.
The kernel indicates the maximum number of bytes for additional scan IEs
using the NL80211_ATTR_MAX_SCAN_IE_LEN attribute. Save this value and
only add additional scan IEs in case the driver can accommodate these
additional IEs.
Bug: http://lists.infradead.org/pipermail/hostap/2022-January/040178.html
Bug-Debian: https://bugs.debian.org/1004524
Bug-ArchLinux: https://bugs.archlinux.org/task/73495
Upstream-Status: Changes Requested [https://patchwork.ozlabs.org/project/hostap/patch/20220130192200.10883-1-mail@david-bauer.net]
Reported-by: Étienne Morice <neon.emorice@mail.com>
Tested-by: Étienne Morice <neon.emorice@mail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The code for hostapd-mbedtls did not work when used for OWE association.
When handling association requests, the buffer offsets and length
assumptions were incorrect, leading to never calculating the y point,
thus denying association.
Also when crafting the association response, the buffer contained the
trailing key-type.
Fix up both issues to adhere to the specification and make
hostapd-mbedtls work with the OWE security type.
Signed-off-by: David Bauer <mail@david-bauer.net>
Configure the PLMN and APN to the modem. This is required in cases,
where either the SGSN or GGSN does not permit the selection of IPv4v6
pdp type.
Previously, the modem always tried to establish a dual-stacked PDP
context regardless of the configured PDP type in uci. As this setting
can not be parameterized when creating a WDS context, configure it to
the modems internal list of profiles. This way, the PDP type is taken
into account when creating the WDS context.
Signed-off-by: David Bauer <mail@david-bauer.net>
The PLMN selection was reset when calling network-register, thus
rendering the sepcific selection of a carrier unapplied.
Set the PLMN selection after executing network-register. This seems to
cause the modem to re-select the carrier eventually.
That being said, qmi does allow the parameterization of the
network-register to include dpecific PLMN settings, however this is
currently not implemented in uqmi.
Signed-off-by: David Bauer <mail@david-bauer.net>
Set the RAT preference before attaching. This handles cases better,
where a network might be available but not with the preferred RAT.
If RAT is changed to a non-available RAT after attach, QMI does not fail
with missing registration but with failing to establish a PDP session.
Signed-off-by: David Bauer <mail@david-bauer.net>
Increase the wait time before polling the connection state for the first
time.
Depending on the prior state of the modem, the first poll might still
return a connected state. The script then tries to establish a PDP
session, which subsequently fails as the modem by then is in scan state.
Increasing the wait-time to 3 seconds mitigates this from happening.
Signed-off-by: David Bauer <mail@david-bauer.net>
On some network-triggered disconnections the UIM state might end up in
"illegal". This prevents the modem from attaching to any network in
non-restricted service modes.
Detect this state and reset the SIM card. This way, the modem can attach
to networks again.
Signed-off-by: David Bauer <mail@david-bauer.net>
Failing the registration does not necessarily mean we can not bring this
interface up. For example, roaming SIM cards are possibly steered by the
home-operator.
Don't block restart of the QMI interface in this case.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0xc22): relocation R_MIPS16_26 against `libxt_DNAT_init' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol printf
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0x400c): relocation R_MIPS16_26 against `iwinfo_close' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
d8118f6 config: make sure timer is not on the timeouts list before freeing
4bbc6e7 add hostsfile output in addition to statefile
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
c8c9f10 uim: fix help formatting
aac0776 uqmi: add APN profile commands
ffc5eea uim: support SIM card power-up/down
d6c963d uim: add application state to SIM status
Signed-off-by: David Bauer <mail@david-bauer.net>
The option 31 in the RA specifies the DNS search list, the support
to configure this via UCI is missing in case dnsmasq-dhcpv6 is used.
This commit uses the uci option domain (same as is done by odhcpd) to
read and pass the DNS search list to dnsmasq, which is then used by RA.
Hence, with this commit, we are able to configure DNS search list for the
RA messages via the uci config when dnsmsaq-dhcpv6 is used.
Signed-off-by: Rahul Thakur <rahul.thakur@iopsys.eu>
479c7f8676d9 cache: make record/hostname lookup case-insensitive
26c97a5a50bf ubus: add a browse flag for suppressing cached ip addresses
c286c51a9bd9 Fix AVL tree traversal in cache_record_find and cache_host_is_known
4035fe42df58 interface: use a global socket instead of per-interface ones
c63d465698c7 cache: dump hostname target from srv records
b42b22152d73 use hostname from SRV record to look up IP addresses
d45c443aa1e6 ubus: add array flag support for the hosts method
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are a few targets that mess with the atm kernel headers. To avoid
incompatibility between kernel and user space during compilation, the
correct headers should be used.
Consequently, the package must also be marked as nonshared.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Modems which are using qmi do not reply on the 1st sync but they do
on subsequent. So qmi.sh is hanging on the first call. Since 2020 uqmi
supports a timeout parameter. Unfortunately qmi.sh didn't make use of
this parameter. So qmi.sh is now invoking an early dummy access to
unlock the modem
Signed-off-by: Uwe Niethammer <uwe@dr-niethammer.de>
Recent hostapd changes just edited the ucode files. It is required to
bump the PKG_RELEASE to include the newest changes in the latest builds.
Signed-off-by: Nick Hainke <vincent@systemli.org>
If the full interface is restarted while bringing up an AP, it can trigger a
wpa_supplicant interface start before wpa_supplicant is notified of the
allocated mac addresses.
Fix this by moving the iface_update_supplicant_macaddr call to just after
the point where mac addresses are allocated.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In the dnsmasq init script, an off-by-one in the range calculation of
ipcalc.sh was mitigated by passing the limit as if its counting started
at zero. This patch removes the mitigation as the off-by-one has been
fixed.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Add a function 'ipcalc' to /lib/functions.sh that sets variables more
safely using export.
With this new function, dnsmasq also handles the return value of ipcalc
correctly.
Fixes: e4bd3de1be ("dnsmasq: refuse to add empty DHCP range")
Co-Authored-By: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
allow to overwrite the detected system capabilities e.g. if devices
does not operate as bridge.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
The patch refresh accidentally moved the hostapd_ucode_free_iface call to
the wrong function
Fixes: e9722aef9e ("hostapd: fix a crash when disabling an interface during channel list update")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining package which have a CPE ID.
Not every package has CPE id.
Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
When STA is disconnected, ensure that the interface is in a cleanly stopped
state:
- if in regular enable/disable state, stop beacons if necessary
- in any other state, disable the interface
When the STA is up, ignore repeated start commands for the same channel, in
order to avoid unnecessary AP restarts
Signed-off-by: Felix Fietkau <nbd@nbd.name>
8e6485a1bcb0 PEAP client: Update Phase 2 authentication requirements
de9a11f4dde9 TTLS client: Support phase2_auth=2
b2a1e7fe7ab9 tests: PEAP and TTLS phase2_auth behavior
518ae8c7cca8 P2P: Do not print control characters in debug
a4c133ea73c7 WPS: Optimize attribute parsing workaround
7a37a94eaa0d Check whether element parsing has failed
f80d83368818 ACS: Remove invalid debug print
fb2b7858a728 FILS: Fix HE MCS field initialization
50ee26fc7044 P2P: Check p2p_channel_select() return value
a50d1ea6a2b3 Add QCA vendor attributes for user defined power save parameters
4636476b7f22 Set RRM used config if the (Re)Association Request frame has RRM IE
e53d44ac63e8 AP MLD: Use STA assoc link address in external auth status to the driver
99a96b2f9df7 AP MLD: OWE when SME is offloaded to the driver
96deacf5d710 nl80211: Skip STA MLO link channel switch handling in AP mode
d320692d918a AP MLD: Handle new STA event when using SME offload to the driver
faee8b99e928 tests: Fix eht_mld_sae_legacy_client to restore sae_pwe
c3f465c56c94 wlantest: Handle variable length MIC field in EAPOL-Key with OWE
605034240e0c wlantest: Support multiple input files
053bd8af8ed2 Recognize FTE MLO subelements
43b5f11d969a Defragmentation of FTE
3973300b8ded FTE protected element check for MLO Reassociation Response frame
74e4a0a6f1e4 wlantest: Learn AP MLD MAC address from Beacon frames
a5a0b2cf7b1b wlantest: Find non-AP MLD only from affiliated BSSs of the AP MLD
74472758584d wlantest: Recognize non-AP MLD based on any link address for decryption
1ffabd697c67 wlantest: Learn non-AP MLD MAC address from (Re)Association Request frames
4e8e515f92b9 wlantest: Use MLO search for the STA in reassociation
49bf9f2df95a wlantest: Use the MLD MAC address as well for matching STA entries
5434a42ec69c wlantest: Search for FT Target AP using MLD MAC address as well
a19fcf685cae wlantest: Include the MLD MAC address of the AP MLD in new-STA prints
709d46da73da wlantest: Do not claim update to AP MD MAC address if no change
770760454f9e wlantest: Do not update BSS entries for other AP MLDs in PTK cloning
084745ffc508 Add QCA vendor attributes for NDP setup
bf9cbb462fd9 Fix writing of BIGTK in FT protocol
011775af9443 tests: Check for beacon loss when using beacon protection
8f148d51322f Fix a compiler warning on prototype mismatch
b7db495ad9c9 AP: Fix ieee802_1x_ml_set_sta_authorized()
232667eafe0d Fix CCMP test vector issues
30771e6e05ed Include PTID in PV1 nonce construction for CCMP test vector
34841cfd9aba Minor formatting changes to CCMP test vectors
a685d84139e6 BSS coloring: Fix CCA with multiple BSS
bc0636841a70 wpa_supplicant: Fix configuration parsing error for tx_queue_*
2763d1d97e66 hostapd: Fix AID assignment in multiple BSSID
763a19286e2f AP: Add configuration option to specify the desired MLD address
bd209633eb10 AP: Use is_zero_ether_addr() to check if BSSID is NULL
bc0268d053b4 wlantest: Guess SAE/OWE group from EAPOL-Key length mismatch
a94ba5322803 EHT: Support puncturing for 320 MHz channel bandwidth
7e1f5c44c97e EHT: 320 MHz DFS support
6f293b32112a QCA vendor attributes for updating roaming AP BSSID info
5856373554eb Extend QCA vendor command to include more parameters for netdev events
e080930aa0a5 Define QCA vendor roam control RSSI attributes
fe72afe713ad Define QCA vendor attribute for high RSSI roam trigger threshold
47a65ccbfde2 P2P: Clean wpa_s->last_ssid when removing a temporary group network
884125ab7d21 tests: P2P autonomous GO and clearing of networking information
7637d0f25053 P2P: Do not filter pref_freq_list if the driver does not provide one
dd1330b502ff Fix hostapd interface cleanup with multiple interfaces
0a6842d5030e nl80211: Fix beacon rate configuration for legacy rates 36, 48, 54 Mbps
d606efe054d5 tests: Beacon rate configuration for 54 Mbps
f91d10c0e6aa tests: Update RSA 3k certificates
07d3c1177bbb tests: Make sae_proto_hostapd_status_* more robust
1085e3bdc6f6 Update iface->current_mode when fetching new hw_features
338a78846b44 Add a QCA vendor sub command for transmit latency statistics
9318db7c38bc wlantest: Use local variables for AA/SPA in FT Request/Response processing
628b9f10223d wlantest: Derive PMK-R1 and PTK using AA/SPA for MLO FT over-the-DS
104aa291e5c8 wlantest: Fix FT over-the-DS decryption
37c87efecfe3 wlantest: Search SPA using MLO aware find for FT Request/Response frame
19f33d7929e8 wlantest: Learn the Link ID for AP MLD affiliated BSSs
6ae43bb10323 wlantest: Learn link address for assoc link from (Re)Association Request
4c079dcc64da Increment hmac_sha*_vector() maximum num_elem value to 25
e6f64a8e1daf FT: FTE MIC calculation for MLO Reassociation Request frame
a83575df5994 wlantest: FTE MIC calculation for MLO Reassociation Request frames
ff02f734baf8 wlantest: Allow specific link BSS to be found with bss_find_mld()
7381c60db8f0 FT: Make FTE MIC calculation more flexible
ac9bf1cc2a4c Decrement hmac_sha*_vector() maximum num_elem value to 11
aa08d9d76803 Fix use of defragmented FTE information
78b153f90a74 Calculate defragmented FTE length during IE parsing
8cf919ffd5c4 wlantest: FTE MIC calculation for MLO Reassociation Response frame
d12a3dce82a9 wlantest: Store and check SNonce/ANonce for FT Authentication
20febfd7838d wlantest: Dump MLO association information in debug
609864d6a8a1 Add QCA vendor attribute to configure MLD ID in ML probe request
12154861e24a Add support for conversion to little endian for 24 bits
c437665041c0 Add Non EHT SCS Capability in (Re)Association Request frames
33da386553b7 SCS: Add support for QoS Characteristics in SCS request
edfca280cbe8 SCS: Add support for optional QoS Charateristics parameters
32dcec9529ec Send actual MFP configuration when driver takes care of BSS selection
123d16d860fa Update hw_mode when CSA finishes
b3d852560bda Change QCA vendor configure attribution name of peer MAC address
12fabc4765c2 Add QCA vendor attribute for configuring max A-MPDU aggregation count
f6eaa7b729cb Add QCA vendor attribute for TTLM negotiation support type
f6dcd326fea7 wlantest: Indicate ToDS/FromDS values for BSS DATA entries
6ce745bb87d4 wlantest: MLO support for decrypting 4-address frames
850dc1482953 wlantest: Remove duplicated A1/A2/A3 override detection for MLO
770e5a808fbb wlantest: Determine whether A1 points to STA once in rx_data_bss_prot()
377d617b574a Define new BSS command info mask for AP MLD address
d3ab6e001f62 wlantest: Use non-AP MLD's MLD MAC address in FT over-the-air derivation
a845601ffe32 wlantest: Derive PTK in MLO using MLD MAC addresses for FT over-the-air
0cd2bfc8a402 wlantest: Fix FTE MIC calculation for MLO Reassociation Response frames
528abdeb673b wlantest: Learn group keys from MLO FT Reassociation Response frames
990600753dd9 wlantest: Defragment Basic MLE before processing
de043ec01ab5 wlantest: Defragment the Per-STA Profile subelement
bae1ec693c44 wlantest: Minimal parsing of Basic MLE STA Profile
ba1579f3bf7c Clear BIGTK values from wpa_supplicant state machine when not needed
b46c4b9a916a tests: Beacon protection and reconnection
3e71516936b7 Document per-ESS MAC address (mac_addr=3 and mac_value)
f85b2b2dee3b Extend wpa_parse_kde_ies() to include EHT capabilities
e3a68081bc1e driver: Add option for link ID to be specified for send_tdls_mgmt()
c7561502f2e8 nl80211: Use a QCA vendor command to set the link for TDLS Discovery Response
a41c8dbdd84e TDLS: Copy peer's EHT capabilities
626501434be1 TDLS: Learn MLD link ID from TDLS Discovery Response
5f30f62eead7 TDLS: Reply to Discovery Request on the link with matching BSSID
940ef9a05c0f TDLS: Use link-specific BSSID instead of sm->bssid for MLO cases
f429064189c3 TDLS: Set EHT/MLO information for TDLS STA into the driver
dd25885a9daa Remove space-before-tab in QCA vendor related definitions
af6e0306b2a9 Fix typos in QCA vendor related definitions
4c9af238c1e4 Fix inconsistent whitespace use in QCA vendor related definitions
e5ccbfc69ecf Split long comment lines in QCA vendor related definitions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MAC address and interface name assigned by mac80211.sh depend on the order in
which interfaces are brought up. This order changes when interfaces get added
or removed, which can cause unnecessary reload churn.
One part of the fix it making MAC address allocation more dynamic in both
wpa_supplicant and hostapd, by ignoring the provided MAC address using
the next available one, whenever the config does not explicitly specify one.
The other part is making use of support for renaming netdevs at runtime and
preserving the MAC address for renamed netdevs.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
set_config causes the ucode bss resource to be re-created and because of that
the bss list needs to be updated as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When switching from a STA-only configuration to AP+STA on the same phy, the
STA was previously restarted in order to notify hostapd of the new frequency,
which might not match the AP configuration.
Fix the STA restart by querying the operating frequency from within hostapd
when bringing up the AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
f429bd94f99e system-linux: switch to new ETHTOOL_xLINKSETTINGS API
Fixes AN announcement for speeds beyond 1 GBit/s.
Adds new UCI options for Ethernet devices:
- autoneg: switch on or off auto-negotiation
- pause: if set to 0, do not announce symmetric flow control capability
- asym_pause: if set to 0, do not announce asymmetric flow control
capability.
- rxpause: if set overrides AN and forces RX pause accordingly
- txpause: if set overrides AN and forces TX pause accordingly
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
db3934d2f740 scripts/netifd-wireless.sh: properly fix WPA3 Enterprise support
Support the following values for the different WPA3 Enterprise modes:
- wpa3-mixed: WPA3 Enterprise transitional mode
This supports EAP with both SHA1 and SHA-256, with optional MFP
- wpa3: WPA3 Enterprise only mode
This supports only SHA256 with mandatory MFP
- wpa3-192: WPA3 Enterprise with mandatory 192 bit support
This uses only GCMP-256 ciphers
Disable 192 bit support and GCMP-256 ciphers for the regular "wpa3" mode.
It seems that even leaving in optional 192 bit support breaks auth on some
clients, including iOS devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
WPA3 Enterprise-transitional requires optional MFP support and SHA1+SHA256
WPA3 Enterprise-only requires SHA1 support disabled and mandatory MFP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It seems that this was not functioning properly and was likely completely unused.
Keeping this out of tree also introduced some annoying churn when updating, because
of the iw nl80211.h sync patch.
If this is needed, it will be reintroduced when/if it is added upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the STA is brought up, it is set to DISABLED before adding the bss to ucode,
so the first trigger to disable the AP is missed.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit e978072baaca ("Do prune_association only after the STA is
authorized") causes issues when an STA roams from one interface to
another interface on the same PHY. The mt7915 driver is not able to
handle this properly. While the commits fixes a DoS, there are other
devices and drivers with the same limitation, so revert to the orginal
behavior for now, until we have a better solution in place.
Fixes: #13156
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
It cannot be properly cloned, since it is attached to the resource type.
Use a separate registry for data. Fixes object confusion issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
An active client mode interface could prevent the AP from claiming its channel
and mess up the bringup sequence order
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Drop obsolete control interface patches.
This fixes some corner cases in the previous code where the segment 0 center
frequency was not adjusted properly, leading to logspam and non-working AP
interfaces.
Additionally, shutting down the AP was broken, because the next beacon update
would re-enable it, leading to a race condition on assoc.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes this error: hostapd: nl80211: kernel reports: integer out of range
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check the phy before removing unrelated netdevs on the same hw device
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When building xdp-tools with CONFIG_USE_LLVM_HOST=y, on a host that
enabled stack protector by default in Clang, compilation fails with the
following error:
CLANG xdp-dispatcher.o
clang-16: error: ignoring '-fstack-protector-strong' option as it is not currently supported for target 'bpfeb' [-Werror,-Woption-ignored]
Add -fno-stack-protector to BPF_CFLAGS to fix this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Include AP ucode source file
Fixes: e56c5f7b27 ("hostapd: add ucode support, use ucode for the main ubus object")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
8c2758b4fbbb wireless: add support for replacing data blobs at runtime
0ff22a6a68ce wireless: enable dynamic reconfiguration by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This implements vastly improved dynamic configuration reload support.
It can handle configuration changes on individual wifi interfaces, as well
as adding/removing interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used to run a standalone EAP server that can be used from
other APs. It uses json as user database format and can automatically
handle reload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
At least Fedora and RHEL 9 set RSAMinSize=2048, so when trying to use
failsafe, we get 'Bad server host key: Invalid key length'
To workaround the issue, we can use: ssh -o RSAMinSize=1024 ...
Generating 2048 bits RSA is extremely slow, so add ed25519.
We keep RSA 1024 to be as compatible as possible.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
ChangeLog:
125b080 Release version 6.4.
5660918 update UAPI header copies
f493e63 netlink: fix duplex setting
b3e341c cmis: report LOL / LOS / Tx Fault
045d8db sff-8636: report LOL / LOS / Tx Fault
a6505f3 drop checks for macros provided in UAPI header copies
86c0c41 do not check for strtol() function
dd8e3ae actually check for C11 compiler
43e4d30 add local copies of macros from autoconf-archive
faa4700 drop check for big endian types
31b7b5e Require a compiler with support for C11 features
946d18b update UAPI header copies
eebf01f ethtool: Add support for configuring tx-push-buf-len
2782ea8 update UAPI header copies
Signed-off-by: Nick Hainke <vincent@systemli.org>
d1f07cf devices: add device id for Atheros AR9287 and AR9380
65ea345 nl80211: constify a few arrays
ca79f64 lib: report byte counters as 64 bit values
This contains an ABI change, increase the ABI version too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
493e1589bc8b bridge: fix coverity false positive report
03a619947717 bridge: add support for configuring extra vlans for the bridge itself
4bea6d21a9ab wireless: fix changing reconf/serialize options in configuration
255b4d5c472e wireless: fix handling config reload with reconf=1
1ab992a74b43 wireless: fix another reconf issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
5211264 odhcpd: add support for dhcpv6_pd_min_len parameter
c6bff6f router: Add PREF64 (RFC 8781) support
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
1571e18e4a69 bridge: add support for configuring extra tagged vlans on member devices
b719f189f243 bridge: make hotplug-added vlans default to tagged
edf3aced9f9a bridge: add support for adding vlan ranges via hotplug
Signed-off-by: Felix Fietkau <nbd@nbd.name>
077e05f2b129 vlan/vlandev: pass through extra vlan information passed via hotplug
40fad91eb5be wireless: add network_vlan config attribute
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add an UCI option to enable Multiple BSSID Advertisement. Enabling this
will announce all BSSIDS on a phy in a single beacon frame. The
interface that is brought up first will be the transmitting profile, all
others are non-transmitting profiles and will be advertised in the
Multiple BSSID element in Beacon and Probe Response frames of the first
interface.
This depends on driver and client support. Enabling this will result in
all but the first interface not being visible at all for clients that do
not support it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Backport patches improving ppp interface creation. As a side effect this
also fix a bug from using netdev trigger that suffer from LED state
wrongly set due to using old ioctl for ppp creation.
Tested-by: Csaba Sipos <metro4@freemail.hu>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the repository
link to the new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
If dual-stack configuration is in use, and dhcpv6 option is set, do not start
464xlat sub-interface for dhcpv6 sub-interace , as the configuration already
provides IPv4 connectivty, be it through single or dual APN configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add two new "v6apn" and "v6profile" properties, to support split-APN
dual-stack onfiguration. This extends the existing ipv4v6 PDP type,
allowing simultaneous connection to two distinct APNs,
one for IPv4 and one for IPv6.
The parameters override existing 'apn' and 'profile' respectively,
if set, but only for IPv6 part of the connection.
If unset, they default to their original values, constituting a standard
IPv4v6 setup.
If a different APN is set for IPv6, a corresponding profile MUST also be
configured, with a different ID, than the IPv4 profile, for example,
profile 2.
Both APNs must match ones configured through QMI or through 'AT+CGDCONT'
command.
Example configuration in UCI:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option autoconnect '1'
option pdptype 'ipv4v6'
option apn 'internet'
option v6apn 'internetipv6'
option profile '1'
option v6profile '2'
Corresponding profile configuration:
AT+CGDCONT?
+CGDCONT: 1,"IP","internet","0.0.0.0",0,0,0,0
+CGDCONT: 2,"IPV6","internetipv6","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The cli is a one-time run, and memory leaks would have been irrelevant. But people call libsw with cli programs as samples.
Doing a good job of memory management calls means that people who call libsw are not so easy to make mistakes.
Signed-off-by: nichel Chen <nichelnich@gmail.com>
412d03012f13 network: prevent adding endpoint routes for addresses on the network
faaf9cee6ef4 utils: fix ipv4 checksum issue
0e1c2fad3540 pex-msg: fix memory leak on fread fail in pex_msg_update_request_init
51be0ed659d0 host: fix crash parsing gateway when no endpoint is specified
ca17601dc24e wg-linux: add support for splitting netlink messages for allowed ips
7d3986b7a5a2 wg-linux: increase default messages size
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Contains following changes:
* bridge: bridge_dump_info: add dumping of bridge attributes
* bridge: make it more clear why the config was applied
* cmake: fix build by reordering the cflags definitions
* treewide: fix multiple compiler warnings
Signed-off-by: Petr Štetiar <ynezz@true.cz>
My original bpftools package made "variant" builds of bpftool and libbpf
as a convenience, since both used the same local kernel sources with the
same versioning. This is no longer the case, since the commit below
switched to using an out-of-tree build mirror hosting repos for each.
Replace bpftools with separate bpftool and libbpf packages, each simplified
and correctly versioned. Also fix the broken libbpf ABI introduced in the
same commit. Existing build .config files are not impacted.
Fixes: 00cbf6f6ab ("bpftools: update to standalone bpftools + libbpf, use the latest version")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
adds ForceCommand option. If the command is specified,
it forces users to execute the command when they log in.
Signed-off-by: Nozomi Miyamori <inspc43313@yahoo.co.jp>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Update to umdns HEAD to include latest enhancements for browse method
filtering, return of TXT records as an array, dumping IPv4/6 as an
array, and including the interface name in a browse reply.
Signed-off-by: Mark Baker <mark@vpost.net>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x, mt7621, x86_64
TOZED TL70-C is an LTE CAT6 cellular modem based on UNISOC SL8563. UNISOC
was formerly called Spreadtrum hence the manufacturer name detected on the
modem is spreadtrum.
The connect and disconnect commands bring up and down the usb0 interface.
They are Base64 encoded as that's what the AT command accepts. The modem
can do up to 4 APNs by bringing the USB interfaces, usb0 to usb3, up.
Setting the USB interfaces up:
connmanctl ndisdial AT^NDISDUN="usb0",1,1
connmanctl ndisdial AT^NDISDUN="usb1",1,2
connmanctl ndisdial AT^NDISDUN="usb2",1,3
connmanctl ndisdial AT^NDISDUN="usb3",1,4
Setting the USB interfaces down:
connmanctl ndisdial AT^NDISDUN="usb0",0,1
connmanctl ndisdial AT^NDISDUN="usb1",0,2
connmanctl ndisdial AT^NDISDUN="usb2",0,3
connmanctl ndisdial AT^NDISDUN="usb3",0,4
Co-developed-by: Andre Cruz <me@1conan.com>
Signed-off-by: Andre Cruz <me@1conan.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
add description for medion usb lte webstick
Signed-off-by: Joe Cooper <highjagger+github@gmail.com>
[bump PKG_RELEASE]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Based on Paul Fertser <fercerpav@gmail.com>'s guidance:
Change AUTORELEASE in rules.mk to:
```
AUTORELEASE = $(if $(DUMP),0,$(shell sed -i "s/\$$(AUTORELEASE)/$(call commitcount,1)/" $(CURDIR)/Makefile))
```
then update all affected packages by:
```
for i in $(git grep -l PKG_RELEASE:=.*AUTORELEASE | sed 's^.*/\([^/]*\)/Makefile^\1^';);
do
make package/$i/clean
done
```
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
d4f56f0e6971 add support for handling traffic to/from the bridge device
3ea579064c00 nl: add separate socket for netlink commands
4ec5a51c6d01 nl: fetch packet stats for offloaded flows
0319fd080bf5 add support for configuring a fixed output port for a bridge member port
5b730f0c2cf5 bridger-bpf: fix build on older kernels
00af6c6e8350 nl: process IFLA_MASTER in any nl events, but skip wireless events
a2794f95756e bridger-bpf: add bpf_skb_pull_data call
6974093eb036 nl: rework vlan code to use the iflink API
d0f79a16c749 nl: do not attempt to enable flow offload on older kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allowing the (kernel) packet priority to be set through UCI.
This makes it straightforward to set some VLAN priority for DHCP
requests through a simple egress qos map. (Avoiding the need for
firewall matching and marking through iptables, which prevents using
flow offloading).
(Such priority tag is a hard requirement for some ISPs, such as Orange
in France).
Depends on: https://github.com/openwrt/odhcp6c/pull/74
Signed-off-by: Pacien TRAN-GIRARD <pacien.trangirard@pacien.net>
To support the widest variety of modems, allow restoring previous
behaviour of configuring the link throug means of DHCP(v6) exclusively.
Change the default value of "dhcp" and "dhcpv6" UCI options to "auto",
while keeping the default behaviour of "prefer out-of-band configuration",
intact. Setting "dhcp" or "dhcpv6" to boolean 1 will now force using
DHCP and DHCPv6, respectively.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
In MBIM interfaces, DNS servers may be provided out-of-band regardless
whether DHCP is used for configuration, or not. Move the DNS
configuration outside "if" blocks to support that.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Beginnings and endings of sub-interface creation procedure were
literally duplicates - extract them outside if "if" blocks
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Allow setting interface MTU through UCI. If this is not set,
use MBIM-provided MTU, if provided through control channel.
If separate MTUs are provided for IPv4 and IPv6, apply larger of them.
This is very unlikely and possible only for IPv4v6 dual-stack configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Delegate prefixes received through MBIM control channel the same way, as
would be done through DHCP, according to RFC7278.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
MBIM supports multiple values for IP address and DNS server, and such
configuration is available through output of MBIM. Use new helper
method to support adding multiple addresses and DNS servers to static
interfaces for both IPv4 and IPv6.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add a new helper to extract IP configuration from umbim output. This is
required to extract fields which can possibly have multiple values,
namely IP addresses and DNS servers, and get rid of primitive parser
using 'eval' builtin without support for this.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Display full configuration obtained using MBIM control channel in the
log, from umbim output verbatim, for easier troubleshooting, and in
preparation for parser refactoring.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Inspired by commti e51aa699f7, allow setting specific routing tables
via ip4table and ip6table options, by passing them on child interfaces
created by MBIM protocol handler.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Finally, inspired by ModemManager's logic, make static configuration
obtained through MBIM control channel, preferred.
If IP configuration is not available this way, fallback to DHCP(v6) if
enabled, else do not create a sub-interface for unavailable IP type.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Now, that sub-interface setup is split by IP type, and separate checks
are performed for DHCP selection, it is possible to control DHCP on v4
an v6 sub-interfaces instantly. Add "dhcpv6" variable, akin to QMI
option, to control behaviour of DHCPv6 separately from IPv4 option,
which is required for some mobile operators.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Check whether interface is configured per IP type, not per DHCP. This is
preparation to allow fallback to DHCP if static IP configuration is not
available, which is the default option for MBIM modems
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Fix an issue where subinterfaces were not added to the same
firewall zone as their parent.
Inspired by 64bb88841f.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
MBIM protocol handler should intherit "peerdns" options from parent
interface on sub-interfaces, otherwise upstream DNS servers are applied
regardless of configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Previously, DHCP was used. According to MBIM Specification v1.0 errata 1 [1],
section 10.5.20, MBIM_CID_IP_CONFIGURATION,
if MBIM information element containing IP configuration is available,
host shall use it, and fall back to in-band mechanisms to acquire it therwise -
therefore make static configuration the default.
[1] https://www.usb.org/document-library/mobile-broadband-interface-model-v10-errata-1-and-adopters-agreement
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Current implementation needlessly creates both IPv4 and IPv6
sub-interfaces for single-stack IP types. Limit this only to selected IP
type. While at that, ensure that IP type is also passed to umbim during
"connect" phase. In addition, detect the actual established connection
type returned by umbim and set up subinterfaces according to that,
not to requested configuration. While at that, allow empty IP type explicitly,
interpreted as "any" according to MBIM specification.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Subsequent calls to 'umbim connect' do not have any effect if a failure
occured, and in such case an infinite loop without timeout is created,
leading to possibility of interface stuck at connecting forever.
Drop this loop, and issue MBIM disconnect properly, so netifd can
restart from scratch.
This issue can be observed with Sierra EM7455 at changing APN, which
causes network re-registration by default, and a MBIM transaction
timeout, which is resolved on next interface bringup by netifd.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Previous implementation automatically set up connections for both IPv4
and IPv6, even if one of them isn't supported. Respect the "pdptype"
option in the same way, as it is done for QMI or NCM, and only start the
respective PDN sessions, if set.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
There are mbim compatible wwan modules available which do not support
the dhcp autoconfiguration. (e.g. gemalto Cinterion ELS81)
This adds the possibility to get the configuration parameters from mbim.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
40ab806 config: use dedicated link local function to check interface
a84bff2 netlink: add support for getting interface linklocal
2ea065f Revert "config: recheck have_link_local on interface reload if already init"
4b38e6b config: fix feature for enabling service only when interface RUNNING
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some modems (namely, Telit LE910C4) require the IPv6 connection state to
be cleared explicitly, to avoid reporting "no effect" if IPv6
connection is already connected through autoconnect mechanism, or during
LTE default bearer attach, which would lead to established session, but
without a way to inform protocol handler of the status.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Some modems require CID to be set explicitly during IPv6 connection
status check, others require IPv6 address family to be checked explicitly
after establishing connection, in order to provide correct status.
Set both fields in the request to satisfy them.
Fixes: c8a88118af ("uqmi: set CID during 'query-data-status' operation")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Given ipv6 has SLAAC it is quite plausible to wish to use dynamic
dhcp4 but static dhcp6. This patch keeps dynamicdhcp as the default
option for both, but is overridden by dynamicdhcpv6 or dynamicdhcpv4
Signed-off-by: Ian Dall <ian@beware.dropbear.id.au>
The dhcphostsfile must be mounted into the (ujail) sandbox.
The file can not be accessed without this mount.
Signed-off-by: Ruben Jenster <rjenster@gmail.com>
The Mikrotik R11e-LTE6 modem is similar to ZTE MF286R modem, added
earlier: it has a Marvel chip, able to work in ACM+RNDIS mode, knows ZTE
specific commands, runs OpenWrt Barrier Breaker fork.
While the modem is able to offer IPv6 address, the RNDIS setup is unable
to complete if there is an IPv6 adress.
While it works in ACM+RNDIS mode, the user experience isn't as good as
with "proto 3g": the modem happily serves a local IP (192.168.1.xxx)
without internet access. Of course, if the modem has enough time
(for example at the second dialup), it will serve a public IP.
Modifing the DHCP Lease (to a short interval before connect and back to
default while finalizing) is a workaround to get a public IP at the
first try.
A safe workaround for this is to excercise an offline script of the
pingcheck program: simply restart (ifdown - ifup) the connection.
Another pitfall is that the modem writes a few messages at startup,
which confuses the manufacturer detection algorithm and got disabled.
daemon.notice netifd: Interface 'mikrotik' is setting up now
daemon.notice netifd: mikrotik (2366): Failed to parse message data
daemon.notice netifd: mikrotik (2366): WARNING: Variable 'ok' does not exist or is not an array/object
daemon.notice netifd: mikrotik (2366): Unsupported modem
daemon.notice netifd: mikrotik (2426): Stopping network mikrotik
daemon.notice netifd: mikrotik (2426): Failed to parse message data
daemon.notice netifd: mikrotik (2426): WARNING: Variable '*simdetec:1,sim' does not exist or is not an array/object
daemon.notice netifd: mikrotik (2426): Unsupported modem
daemon.notice netifd: Interface 'mikrotik' is now down
A workaround for this is to use the "delay" option in the interface
configuration.
I want to thank Forum members dchard (in topic Adding support for
MikroTik hAP ac3 LTE6 kit (D53GR_5HacD2HnD)) [1]
and mrhaav (in topic OpenWrt X86_64 + Mikrotik R11e-LTE6) [2]
for sharing their experiments and works.
Another information page was found at eko.one.pl [3].
[1]: https://forum.openwrt.org/t/137555
[2]: https://forum.openwrt.org/t/151743
[3]: https://eko.one.pl/?p=modem-r11elte
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
The MikroTik R11e-LTE6 modem goes into flight mode (CFUN=4) at startup
and the radio is off (*RADIOPOWER: 0):
AT+RESET
OK
OK
*SIMDETEC:2,NOS
*SIMDETEC:1,SIM
*ICCID: 8936500119010596302
*EUICC: 1
+MSTK: 11, D025....74F3
*ADMINDATA: 0, 2, 0
+CPIN: READY
*EUICC: 1
*ECCLIST: 5, 0, 112, 0, 000, 0, 08, 0, 118, 0, 911
+CREG: 0
$CREG: 0
+CESQ: 99,99,255,255,255,255
*CESQ: 99,99,255,255,255,255,0
+CGREG: 0
+CEREG: 0
+CESQ: 99,99,255,255,255,255
*CESQ: 99,99,255,255,255,255,0
*RADIOPOWER: 0
+MMSG: 0, 0
+MMSG: 0, 0
+MMSG: 1, 0
+MPBK: 1
While the chat script is able to establish the PPP connection,
it's closed instantly by the modem: LCP terminated by peer.
local2.info chat[7000]: send (ATD*99***1#^M)
local2.info chat[7000]: expect (CONNECT)
local2.info chat[7000]: ^M
local2.info chat[7000]: ATD*99***1#^M^M
local2.info chat[7000]: CONNECT
local2.info chat[7000]: -- got it
local2.info chat[7000]: send ( ^M)
daemon.info pppd[6997]: Serial connection established.
kern.info kernel: [ 453.659146] 3g-mikrotik: renamed from ppp0
daemon.info pppd[6997]: Renamed interface ppp0 to 3g-mikrotik
daemon.info pppd[6997]: Using interface 3g-mikrotik
daemon.notice pppd[6997]: Connect: 3g-mikrotik <--> /dev/ttyACM0
daemon.info pppd[6997]: LCP terminated by peer
daemon.notice pppd[6997]: Connection terminated.
daemon.notice pppd[6997]: Modem hangup
daemon.info pppd[6997]: Exit.
daemon.notice netifd: Interface 'mikrotik' is now down
Sending "AT+CFUN=1" to modem deactivates the flight mode and
solves the issue:
daemon.notice netifd: Interface 'mikrotik' is setting up now
daemon.notice netifd: mikrotik (7051): sending -> AT+CFUN=1
daemon.notice pppd[7137]: pppd 2.4.9 started by root, uid 0
local2.info chat[7140]: abort on (BUSY)
local2.info chat[7140]: abort on (NO CARRIER)
local2.info chat[7140]: abort on (ERROR)
local2.info chat[7140]: report (CONNECT)
local2.info chat[7140]: timeout set to 10 seconds
local2.info chat[7140]: send (AT&F^M)
local2.info chat[7140]: expect (OK)
local2.info chat[7140]: ^M
local2.info chat[7140]: +CESQ: 99,99,255,255,255,255^M
local2.info chat[7140]: ^M
local2.info chat[7140]: *CESQ: 99,99,255,255,255,255,0^M
local2.info chat[7140]: AT&F^MAT&F^M^M
local2.info chat[7140]: OK
local2.info chat[7140]: -- got it
...
local2.info chat[7140]: send (ATD*99***1#^M)
local2.info chat[7140]: expect (CONNECT)
local2.info chat[7140]: ^M
local2.info chat[7140]: ATD*99***1#^M^M
local2.info chat[7140]: CONNECT
local2.info chat[7140]: -- got it
local2.info chat[7140]: send ( ^M)
daemon.info pppd[7137]: Serial connection established.
kern.info kernel: [ 463.094254] 3g-mikrotik: renamed from ppp0
daemon.info pppd[7137]: Renamed interface ppp0 to 3g-mikrotik
daemon.info pppd[7137]: Using interface 3g-mikrotik
daemon.notice pppd[7137]: Connect: 3g-mikrotik <--> /dev/ttyACM0
daemon.warn pppd[7137]: Could not determine remote IP address: defaulting to 10.64.64.64
daemon.notice pppd[7137]: local IP address 100.112.63.62
daemon.notice pppd[7137]: remote IP address 10.64.64.64
daemon.notice pppd[7137]: primary DNS address 185.29.83.64
daemon.notice pppd[7137]: secondary DNS address 185.62.131.64
daemon.notice netifd: Network device '3g-mikrotik' link is up
daemon.notice netifd: Interface 'mikrotik' is now up
To send this AT command to the modem the "runcommand.gcom" script
dependency is moved from comgt-ncm to comgt.
As the comgt-ncm package depends on comgt already, this change
is a NOOP from that point of view.
But from the modem's point it is a low hanging fruit as the modem
is usable with installing comgt and kmod-usb-ncm packages.
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
This patch solves the problem of receiving "error" responses when
initially calling gcom. This avoids unnecessary NO_DEVICE failures.
A retry loop retries the call after an "error" response within the
specified delay. A successful response will continue with the connection
immediately without waiting for max specified delay, bringing the
interface up sooner.
Signed-off-by: Mike Wilson <mikewse@hotmail.com>
7c0f603 router: skip RA and wait for LINK-LOCAL to be assigned
ba30afc config: skip interface setup if interface not IFF_RUNNING
06b111e Revert "odhcpd: Reduce error messages"
90d6cc9 odhcpd: Reduce error messages
Also drop AUTORELEASE since it got deprecated.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reduces open coding and allows to easily add a knob to enable
it treewide, where chosen packages can still opt-out via "no-lto".
Some packages used LTO, but not the linker plugin. This unifies 'em
all to attempt to produce better code.
Quoting man gcc(1):
"This improves the quality of optimization by exposing more code to the
link-time optimizer."
Also use -flto=auto instead of -flto=jobserver, as it's not guaranteed
that every buildsystem uses +$(MAKE) correctly.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This reduces open coding and allows to easily add a knob to
enable it treewide, where chosen packages can still opt-out via
"no-gc-sections".
Note: libnl, mbedtls and opkg only used the CFLAGS part without the
LDFLAGS counterpart. That doesn't help at all if the goal is to produce
smaller binaries. I consider that an accident, and this fixes it.
Note: there are also packages using only the LDFLAGS part. I didn't
touch those, as gc might have been disabled via CFLAGS intentionally.
Signed-off-by: Andre Heider <a.heider@gmail.com>
odhcp6c logs messages related to its activity when invoked with -v, but
there is no way to configure this from within OpenWrt. This adds a UCI
option to turn on odhcp6c logging, disabled by default. To enable, set,
for example, network.wan6.verbose = 1.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
This allows adding backup servers, in case the primary ones fail.
Assume that port and shared secret are going to be the same.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
binutils 2.39: https://lists.gnu.org/archive/html/info-gnu/2022-08/msg00002.html
binutils 2.40: https://lists.gnu.org/archive/html/info-gnu/2023-01/msg00003.html
This version includes a new libsframe.so library, pack it into the
libbfd package as it is used by this library. Also deactivate some
optional configuration options for now.
An extra patch to fix compile problem in AARCH64 is added.
gprofng needs a C++ standard library, deactivate it for now.
Activate feature-disassembler-init-styled in bpftools too to fix
compilation with the updated binutils.
An bpftool version 7.0 or later is needed for binutils 2.39 and later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
bpftool changelog: https://github.com/libbpf/bpftool/releases
libbpf changelog: https://github.com/libbpf/libbpf/releases
This updates the bfptool to version 7.1.0. This also includes an update
of the libbpf to version 1.1.
This also adds some new feature options and removes some old ones which
were also removed form the source code. zlib for example is now
mandatory.
Add -flto also to LD flags to make it really work.
Before this change bpftool was on a git commit between version 6.7 and
6.8 and libbpf was on a commit between version 0.7 and 0.8.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Release notes:
- Feature: link down event statistics (no option)
- Feature: JSON output for coalesce (-c)
- Feature: new link modes (no option)
- Feature: JSON output for ring (-g)
- Feature: netlink handler for RSS get (-x)
- Fix: fix boolean value output in JSON output
- Fix: fix build errors and warnings
Remove upstreamed patches:
- 100-uapi-Bring-in-if-h.patch
- 101-netlink-Fix-maybe-uninitialized-meters-variable.patch
- 102-raw-marvell-c-Fix-build-with-musl-libc.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
This patch fixes a corner case when using passwords that are exactly 64
characters in length with mesh mode or passwords longer than 63 characters
with SAE because 'psk' is used instead of 'sae_password'.
SAE is obligatory for 802.11s (mesh point).
The 'psk' option for hostapd is suited for WPA2 and enforces length
restrictions on passwords. Values of 64 characters are treated as PMKs.
With SAE, PMKs are always generated during the handshake and there are no
length restrictions.
The 'sae_password' option is more suited for SAE and should be used
instead.
Before this patch, the 'sae_password' option is only used with mesh mode
passwords that are not 64 characters long.
As a consequence:
- mesh passwords can't be 64 characters in length
- SAE only works with passwords with lengths >8 and <=63 (due to psk
limitation).
Fix this by always using 'sae_password' with SAE/mesh and applying the PMK
differentiation only when PSK is used.
Fixes: #11324
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Including kernel.mk moves the package build folder in the linux one, which
is confusing since this isn't building any kernel modules.
package-defaults.mk is already included my package.mk.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Package kmod-ipt-raw enables CONFIG_IP_NF_RAW and packages
iptable_raw.ko
According to kernel's net/netfilter/Kconfig there are only 3 kernel
symbols that depend on the IP_NF_RAW:
1. NETFILTER_XT_TARGET_CT (xt_CT.ko)
2. NETFILTER_XT_TARGET_NOTRACK (unused symbol?!)
3. NETFILTER_XT_TARGET_TRACE (xt_TRACE.ko)
Now: iptables-mod-conntrack-extra selects kmod-ipt-conntrack-extra which
provides: xt_helper.ko nf_conncount.ko xt_connlimit.ko xt_connmark.ko
xt_recent.ko and xt_connbytes.ko (none of them seems to require
iptable_raw.ko).
It seems there is no explicit reason for iptables-mod-conntrack-extra to
require kmod-ipt-raw (iptables_raw.ko).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Use ipcalc's return value to react to invalid range specifications.
By simply ignoring the range instead of aborting with an error code,
dnsmasq should still start when there's an error (best effort).
Aborting the config generation or working with invalid range specs leaves
dnsmasq crash-looping which is the right thing to do concerning that
particular interface but it also hinders DHCP service on other interfaces
and DNS on the router itself.
Signed-off-by: Leon M. George <leon@georgemail.eu>
uhttpd's cmake options all default to ON. Either we set all of them or
none if the defaults need to be changed. Let's go with the latter.
Because support for all modules is always compiled in, remove two unused
and useless config toggles.
uhttpd detects and uses libcrypt itself, no need to add it here again.
Signed-off-by: Andre Heider <a.heider@gmail.com>
47561aa mimetypes: add audio/video support for apple airplay
6341357 ucode: respect all arguments passed to send()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dnsmasq DNS cache size is only 150 by default.
Set the uci default value to 1000, so that cache gets used more
and unnecessary DNS queries to upstream can be avoided.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Bump ABI to 20230121 due to struct changes
f766138 cli: print the flags on the frequency list
8ee7971 lib: add IWINFO_FREQ_FLAG_NAMES
81184d2 nl80211: fix some comments
2c4ee84 nl80211: prefer non-supplicant-based devices
6194aaf nl80211: simplify iterating over phy's devices
acbf4fe nl80211: remove redundant check in nl80211_phy2ifname()
0172c97 cli: print the frequency and band on the scan list
bbe424f cli: print the band on the frequency list
afa147c nl80211: add "mhz" and "band" to iwinfo_scanlist_entry
0d5ea34 nl80211: add "band" to iwinfo_freqlist_entry
dba0f06 nl80211: add support for radiation and indoor chan restriction
7e3d7de iwinfo: reorganize iwinfo header to enum and defines
9b47b03 devices: add USB devices supported by the mt76 driver
c0fda7c utils: skip comment lines when parsing devices.txt
dbc0ee7 cli: describe USB devices as such
891acee devices: add MediaTek MT7628 card
fac0787 devices: add support for declaring compatible matched devices
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This uses version 4.23.1 of the dsl_cpe_control package from the Intel
UGW 8.5.2.10 for the VRX518.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[rebased]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 4.23.1, added Jan's vector mac patch, fix warnings,
switch to tag tarball]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[add missing nLine in autoboot script, fix disconnect on termination,
remove unneeded VR9 leftovers in init script]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
There is currently a problem with making reproducible version of lldpd.
The tool version is generated based on 3 source:
1. .dist-version file in release tar
2. git hash with presence of .git directory
3. current date
Using the codeload tar from github results in getting the repo without
the .git directory and since they are not release tar, we don't have
.dist-version. This results in having lldpd bin with a version set to
the current build time.
Switch to release tar so that we correctly have a .dist-version file and
the version is not based on the build time.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
GCC 12.2.0 shows this false positive error message:
````
uqmi-2022-05-04-56cb2d40/dev.c: In function 'qmi_request_wait':
uqmi-2022-05-04-56cb2d40/dev.c:217:23: error: storing the address of local variable 'complete' in '*req.complete' [-Werror=dangling-pointer=]
217 | req->complete = &complete;
| ~~~~~~~~~~~~~~^~~~~~~~~~~
uqmi-2022-05-04-56cb2d40/dev.c:208:14: note: 'complete' declared here
208 | bool complete = false;
| ^~~~~~~~
uqmi-2022-05-04-56cb2d40/dev.c:208:14: note: 'req' declared here
cc1: all warnings being treated as errors
````
and this one:
````
In file included from uqmi-2022-05-04-56cb2d40/commands.c:28:
In function 'blobmsg_close_table',
inlined from 'cmd_nas_get_cell_location_info_cb' at /home/haukeuqmi-2022-05-04-56cb2d40/commands-nas.c:897:4:
/usr/include/libubox/blobmsg.h:256:9: error: 'c' may be used uninitialized [-Werror=maybe-uninitialized]
256 | blob_nest_end(buf, cookie);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from uqmi-2022-05-04-56cb2d40/commands.c:169:
uqmi-2022-05-04-56cb2d40/commands-nas.c: In function 'cmd_nas_get_cell_location_info_cb':
uqmi-2022-05-04-56cb2d40/commands-nas.c:713:15: note: 'c' was declared here
713 | void *c, *t, *cell, *freq;
| ^
cc1: all warnings being treated as errors
````
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
def7755c459d add missing copyright headers
f68307fd96d7 add hairpin mode support
9ee8f433ba4e nl: do not pass NDA_VLAN with vid=0
978c1f9eed07 add support for the bridge port isolated flag
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The ABI of the wolfssl library changed a bit between version 5.5.3 and
5.5.4. This release update will trigger a rebuild of all packages which
are using wolfssl to make sure they are adapted to the new ABI.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2cffe0c44e62 treewide: correctly apply IFNAMSIZ limit
96bcbb2e4eb6 wireless: allow set_retry ubus notify command to trigger a wdev restart
a2e8cd75dbf6 wireless: add support for disabling multicast-to-unicast per virtual interface
e9f44189ade7 system: move netdev types to system-linux.c where they are used
a3fab0119ef1 utils: include utils.h last
7ce73fc16765 vlandev: propagate topology changes
81c1fbcba2f2 device: fix vlan device issues with disappearing lower devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The libraries libpthread, libdl, libutil, libanl have been integrated
into the libc library in version 2.34. it is not needed to explicitly
link them any more.
Most of the functions have been moved from the librt.so into libc.so
some time ago already.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Most relevant feature for openwrt in this release, supports dynamically
removing hosts from 'hostsdir' supplied host files.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Changes since v1.2.8:
32aaf32 libxdp: Fix incorrect rx_ring_setup_done
6049671 headers: add bpf_endian.h for parsing_helpers.h
2682c1c export-man: Ignore errors when executing git shell command
8afda7a xdp-loader/README: Mention lack of support for HW mode in most cards
dc69919 libxdp: fix prog_fd checks for fd >= 0
3d7c22a libxdp: Allow falling back to single-program attachment for loaded programs
af00429 libxdp: Fix check in xdp_program__attach_single()
41703d2 libxdp: Make sure to set the the program autoload when loading a program
b1fd2e5 test-xdpdump: Only run tshark attribute test on newer versions of tshark
5dfe342 libxdp: Convert xdp-dispatcher to use strict section names
929a22e configure: Try to auto-detect versioned clang binaries
074fcfb libxdp: Check program name when determining if a program is a dispatcher
e13a191 Bump TOOLS_VERSION to 1.2.9
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
8d15809 cli: print current HT mode
8f86dd6 cli: use IWINFO_HTMODE_COUNT
f36b72b cli: use IWINFO_KMGMT_NAMES
91be7e0 cli: use IWINFO_CIPHER_NAMES
49b6ec9 cli: fix printing the scan channel width
b1c8873 cli: fix marking the active channel
9e14e64 utils: add iwinfo_band2ghz() and iwinfo_ghz2band() helpers
e084781 utils: add helper functions to get names by values
d09a77a utils: add iwinfo_htmode_is_{ht|vht|he} helpers
8752977 utils: add and use iwinfo_format_hwmodes()
02f433e lib: add IWINFO_80211_COUNT and IWINFO_80211_NAMES
1d30df1 lib: add IWINFO_BAND_COUNT and IWINFO_BAND_NAMES
aefd0ef lib: use common IWINFO_CIPHER_NAMES strings
a5b30de lib: add IWINFO_OPMODE_COUNT and use it for IWINFO_OPMODE_NAMES
9f29e79 lib: constify and fixup the string array definitions
fddc015 nl80211: mark frequencies where HE operation in not allowed
6d50a7c nl80211: add support for HE htmodes
4ba5713 nl80211: properly get available bands for the hwmode
91b2ada nl80211: update the kernel header nl80211.h
3f619a5 nl80211: fix frequency/channel conversion for the 6G band
a77d915 nl80211: don't guess if a name is an ifname
c27ce71 devices: add usb device MediaTek MT7921AU
14f864e nl80211: add ability to describe USB devices
a5a75fd nl80211: remove ancient wpa_supplicant ctrl socket path
dd4e1ff nl80211: fix wpa supplicant ctrl socket permissions
d638163 fix -Wdangling-else warnings
4aa6c5a fix -Wreturn-type warning
3112726 fix -Wpointer-sign warning
ebd5f84 fix -Wmaybe-uninitialized warning
5469898 fix -Wunused-variable warnings
462b679 fix -Wduplicate-decl-specifier warnings
ccaabb4 fix -Wformat-truncation warnings
50380db enable useful compiler warnings via -Wall
Fixes: https://github.com/openwrt/openwrt/issues/10158
Fixes: https://github.com/openwrt/openwrt/issues/10687
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
hostapd's compile time option CONFIG_IEEE80211N was removed almost 3 years
ago, 80.211n/HT is always included since then.
Noticed because `hostapd -v11n` confusingly returned an error.
See hostapd's commit:
f3bcd69603 "Remove CONFIG_IEEE80211N build option"
Signed-off-by: Andre Heider <a.heider@gmail.com>
eee80211_frequency_to_channel() isn't used anymore, which is a leftover from:
2a31e9ca97 "hostapd: add op-class to get_status output"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Allow registration if the SIM is roaming or partner mode, by adding two
new options to the protocol.
Until now, such registration failed because umbim returns exit codes 4 and
5 for such situations.
Signed-off-by: Julio Gonzalez Gil <git@juliogonzalez.es>
700a925 fw4: prevent null access when no ipsets are defined
6443ec7 config: drop input traffic by default
119ee1a ruleset: drop ctstate invalid traffic for masq-enabled zones
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add new UCI list 'addn_mount' allowing the expose additional filesystem
paths to the jailed dnsmasq process. This is useful e.g. in case of
manually configured includes to the configuration file or symlinks
pointing outside of the exposed paths as used by e.g. the safe-search
package in the packages feed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This add --filter-A and --filter-AAAA options, to remove IPv4 or IPv6
addresses from DNS answers. these options is supported since version 2.87.
Co-authored-by: NueXini <nuexini@alumni.tongji.edu.cn>
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
dtim_period is a bss property, not a device one.
It is already handled properly in mac80211.sh
Fixes: 30c64825c7 ("hostapd: add dtim_period, local_pwr_constraint, spectrum_mgmt_required")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add build option for nftables sets. By default disable iptables ipset
support. By default enable nftable nftset support since this is what
fw4 uses.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
dnsmasq: nftset: serve from ipset config
Use existing ipset configs as source for nftsets to be compatible with
existing configs. As the OS can either have iptables XOR nftables
support, it's fine to provide both to dnsmasq. dnsmasq will silently
fail for the present one. Depending on the dnsmasq compile time options,
the ipsets or nftsets option will not be added to the dnsmasq config
file.
dnsmasq will try to add the IP addresses to all sets, regardless of the
IP version defined for the set. Adding an IPv6 to an IPv4 set and vice
versa will silently fail.
Signed-off-by: Mathias Kresin <dev@kresin.me>
dnsmasq: support populating nftsets in addition to ipsets
Tell dnsmasq to populate nftsets instead of ipsets, if firewall4 is present in
the system. Keep the same configuration syntax in /etc/config/dhcp, for
compatibility purposes.
Huge thanks to Jo-Philipp Wich for basically writing the function.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
dnsmasq: obtain nftset ip family from nft
Unfortunately dnsmasq nft is noisy if an attempt to add a mismatched ip address
family to an nft set is made.
Heuristic to guess which ip family a nft set might belong by inferring
from the set name.
In order of preference:
If setname ends with standalone '4' or '6' use that, else
if setname has '4' or '6' delimited by '-' or '_' use that (eg
foo-4-bar) else
If setname begins with '4' or '6' standalone use that.
By standalone I mean not as part of a larger number eg. 24
If the above fails then use the existing nft set query mechanism and if
that fails, well you're stuffed!
With-thanks-to: Jo-Philipp Wich <jo@mein.io> who improved my regexp
knowledge.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
dnsmasq: specify firewall table for nftset
Permit ipsets to specify an nftables table for the set. New config
parameter is 'table'. If not specified the default of 'fw4' is used.
config ipset
list name 'BK_4,BK_6'
option table 'dscpclassify'
option table_family 'ip'
option family '4'
list domain 'ms-acdc.office.com'
list domain 'windowsupdate.com'
list domain 'update.microsoft.com'
list domain 'graph.microsoft.com'
list domain '1drv.ms'
list domain '1drv.com'
The table family can also be specified, usually 'ip' or 'ip6' else the
default 'inet' capable of both ipv4 & ipv6 is used.
If the table family is not specified then finally a family option is
available to specify either '4' or '6' for ipv4 or ipv6 respectively.
This is all in addition to the existing heuristic that will look in the
nftset name for an ip family clue, or in total desperation, query the
value from the nftset itself.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When running sysupgrade from an existing configuration, move existing
ipset definitions to a dedicated config section. Later on, it will allow
to serve ipset as well as nftable sets from the same configuration.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This backports a commit from upstream dnsmasq to fix CVE-2022-0934.
CVE-2022-0934 description:
A single-byte, non-arbitrary write/use-after-free flaw was found in
dnsmasq. This flaw allows an attacker who sends a crafted packet
processed by dnsmasq, potentially causing a denial of service.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Calling /etc/init.d/uhttpd reload directly in the acme hotplug script
can inadvertently start a stopped instance.
Signed-off-by: Glen Huang <i@glenhuang.com>
This is necessary with firewall4 to avoid a hard-to-diagnose race
condition during boot, causing DNAT rules not to be taken into account
correctly.
The root cause is that, during boot, the ruleset is mostly empty, and
interface-related rules (including DNAT rules) are added incrementally.
If a packet hits the input chain before the DNAT rules are setup, it can
create buggy conntrack entries that will persist indefinitely.
This new default should be safe because firewall4 explicitly accepts
authorized traffic and rejects the rest. Thus, in normal operations, the
default policy is not used.
Fixes: #10749
Ref: https://github.com/openwrt/openwrt/issues/10749
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
a92c0a7 dhcpv6-ia: make tmp lease file hidden
4a673e1 fix null pointer dereference for INFORM messages
860ca90 odhcpd: Support for Option NTP and SNTP
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Adding a new method to `ubus call dsl` to retrieve DSL statistics
used to feed the DSL charts (bit allocation, SNR, QLN and HLOG)
Signed-off-by: Roland Barenbrug <roland@treslong.com>
[fix pointer error, clean up]
Signed-off-by: Andre Heider <a.heider@gmail.com>
DSL_G997_LineStatusData_t defines special invalid values, skip these
metrics.
Signed-off-by: Roland Barenbrug <roland@treslong.com>
[split patch]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Common Platform Enumeration (CPE) is a structured naming scheme for
information technology systems, software, and packages.
Suggested-by: Steffen Pfendtner <s.pfendtner@ads-tec.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
4fbf6d7 ruleset.uc: log forwarded traffic not matched by zone policies
c7201a3 main.uc: reintroduce set reload restriction
756f1e2 ruleset: fix emitting set_mark/set_xmark rules with masks
3db4741 ruleset: properly handle zone names starting with a digit
43d8ef5 fw4: fix formatting of default log prefix
592ba45 main.uc: remove uneeded/wrong set reload restrictions
b0a6bff tests: fix testcases
145e159 fw4: recognize `option log` and `option counter` in `config nat` sections
ce050a8 fw4: fall back to device if l3_device is not available in ifstatus
Fixes: #10639, #10965
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add the measurement report value to the beacon reports send via ubus. It
is possible to derive from the measurement report if a station refused to
do a beacon report and why. It is important to know why a station refuses
to do a beacon-report. In particular, we should not request a beacon
report from a station again that refused a beacon-report before.
The rejection reasons can be found by looking at the bits defined by:
- MEASUREMENT_REPORT_MODE_ACCEPT
- MEASUREMENT_REPORT_MODE_REJECT_LATE
- MEASUREMENT_REPORT_MODE_REJECT_INCAPABLE
- MEASUREMENT_REPORT_MODE_REJECT_REFUSED
Suggested-by: Ian Clowes <clowes_ian@hotmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
dhcpv6.script contained support for disabling prefix delegation of 464XLAT
sub-interface, but netifd protocol handler was missing the required
export to disable this. Add missing export, akin to DS-Lite and MAP.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
As wolfSSL is having hard time maintaining ABI compatibility between
releases, we need to manually force rebuild of packages depending on
libwolfssl and thus force their upgrade. Otherwise due to the ABI
handling we would endup with possibly two libwolfssl libraries in the
system, including the patched libwolfssl-5.5.1, but still have
vulnerable services running using the vulnerable libwolfssl-5.4.0.
So in order to propagate update of libwolfssl to latest stable release
done in commit ec8fb542ec ("wolfssl: fix TLSv1.3 RCE in uhttpd by
using 5.5.1-stable (CVE-2022-39173)") which fixes several remotely
exploitable vulnerabilities, we need to bump PKG_RELEASE of all
packages using wolfSSL library.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This will prevent `module is already loaded` lines from
appearing in the logs when a PPP connection is reconnecting
Signed-off-by: Manas Sambhus <manas.sambhus+github@gmail.com>
'rule inet dscpclassify dscp_match meta l4proto { udp } th dport { 3478 }
th sport { 3478-3497, 16384-16387 } goto ct_set_ef' works with
'nft add', but not 'nft insert', the latter yields:
"BUG: unhandled op 4".
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
46f04f3808e8 devices: add MediaTek MT7986 WiSoC
b3e08c8b5a8f ops: make support for wireless extensions optional
1f695d9c7f82 nl80211: allow phy names that don't start with 'phy'
b7f9f06e1594 nl80211: fix phy/netdev index lookup
4a43b0d40ba5 nl80211: look up the phy name instead of assuming name == phy<idx>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Also include the station auth_type in the ubus and log message in order
to detect, if clients used FT or FILS to associate
Signed-off-by: Felix Fietkau <nbd@nbd.name>
b704dc72e tests: sigma_dut and updated ConfResult value for Configurator failures
89de431f2 DPP: Add config response status value to DPP-CONF-SENT
10104915a tests: sigma_dut and DPP PB session overlap
80d5e264c Enhance QCA vendor roam event to indicate MLO links after reassociation
662249306 Update copyright notices for the QCA vendor definitions
8adcdd659 tests: Temporary workaround for dpp_chirp_ap_5g
ddcd15c2d tests: Fix fuzzing/sae build
7fa67861a tests: Fix p2p_channel_avoid3
ee3567d65 tests: Add more time for scan/connection
1d08b238c nl80211: Allow more time for the initial scan with 6 GHz
ac9e6a2ab tests: Allow 6 GHz opclasses in MBO checks
faf9c04cb Remove a host of unnecessary OPENSSL_IS_BORINGSSL ifdefs
b9cd5a82f Always process pending QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH data
ef4cd8e33 QoS: Use common classifier_mask for ipv4/ipv6
93be02592 Add fixed FDD mode to qca_btc_chain_mode QCA vendor attribute
e7cbfa1c1 tests: sigma_dut and DPP Enrollee unsupported curves
5565fbee2 DPP: Check Enrollee supported curves when building Config Response
ceae05cec tests: sigma_dut and DPP MUDURL setting for hostapd
4cfb484e9 DPP: Allow dpp_controller_start without arguments in CLIs
c97000933 Fix ifdef condition for imsi_privacy_cert
2a9a61d6c tests: SAE with extended key AKM
e35f6ed1d tests: More detailed report on SAE PMKSA caching error case
f70db167a SAE: Derive a variable length PMK with the new AKM suites
91010e6f6 SAE: Indicate AKM suite selector in commit for new AKM suites
e81ec0962 SAE: Use H2E unconditionally with the new AKM suites
f8eed2e8b SAE: Store PMK length and AKM in SAE data
9dc4e9d13 SAE: EAPOL-Key and key/MIC length information for the new AKM suites
a32ef3cfb SAE: Driver capability flags for the new SAE AKM suites
91df8c9c6 SAE: Internal WPA_KEY_MGMT_* defines for extended key AKMs
5c8a714b1 SAE: Use wpa_key_mgmt_sae() helper
5456b0f26 Define new RSN AKM suite selector values
def33101c DPP: Clear push button announcement state on wpa_supplicant FLUSH
35587fa8f tests: DPP Controller/Relay with need to discover Controller
d22dfe918 DPP: Event message for indicating when Relay would need a Controller
ca7892e98 tests: DPP Relay and adding/removing connection to a Controller
bfe3cfc38 DPP: Allow Relay connections to Controllers to be added and removed
808834b18 Add a comparison function for hostapd_ip_addr
f7763880b DPP: Advertise Configurator connectivity on Relay automatically
ff7cc1d49 tests: DPP Relay and dynamic Controller addition
ca682f80a DPP: Dynamic Controller initiated connection on Relay
d2388bcca DPP: Strict validation of PKEX peer bootstrapping key during auth
a7b8cef8b DPP3: Fix push button boostrapping key passing through PKEX
69d7c8e6b DPP: Add peer=id entry for PKEX-over-TCP case
b607d2723 tests: sigma_dut and DPP PB Configurator in wpa_supplicant
1ff9251a8 DPP3: Push button Configurator in wpa_supplicant
b94e46bc7 tests: PB Configurator in wpa_supplicant
ca4e82cbf tests: sigma_dut DPP/PKEX initiator as Configurator over TCP and Wi-Fi
e9137950f DPP: Recognize own PKEX Exchange Request if it ends up being received
692956446 DPP: Note PKEX code/identifier deletion in debug log
dfa9183b1 tests: DPP reconfig after Controller-initiated operation through Relay
ae4a3a6f6 DPP: Add DPP-CONF-REQ-RX event for Controller
17216b524 tests: sigma_dut DPP/PKEX initiator as Configurator (TCP) through Relay
fb2937b85 DPP: Allow Controller to initiate PKEX through Relay
15af83cf1 DPP: Delete PKEX code and identifier on success completion of PKEX
d86ed5b72 tests: Allow DPP_PKEX_REMOVE success in dpp_pkex_hostapd_errors
0a4f391b1 tests: sigma_dut and DPP Connector Privacy
479e412a6 DPP3: Default value for dpp_connector_privacy
7d12871ba test: DPP Private Peer Introduction protocol
148de3e0d DPP3: Private Peer Introduction protocol
786ea402b HPKE base mode with single-shot API
f0273bc81 OpenSSL: Remove a forgotten debug print
f2bb0839f test: DPP 3rd party config information
68209ddbe DPP: Allow 3rd party information to be added into config object
0e2217c95 DPP: Allow 3rd party information to be added into config request obj
3d82fbe05 Add QCA vendor subcommand and attributes for SCS rule configuration
16b62ddfa QCA vendor attribute for DBAM configuration
004b1ff47 tests: DPP Controller initiating through Relay
451ede2c3 DPP: Allow AP/Relay to be configured to listed for new TCP connections
248654d36 tests: sigma_dut DPP PB test cases
697b7d7ec tests: DPP push button
7bbe85987 DPP3: Allow external configuration to be specified on AP for PB
8db786a43 DPP3: Testing functionality for push button announcements
37bccfcab DPP3: Push button bootstrap mechanism
a0054fe7c Add AP and STA specific P802.11az security capabilities (vendor command)
159e63613 QCA vendor command for CoAP offload processing
3b7bb17f6 Add QCA vendor attribute for TIM beacon statistics
09a281e52 Add QCA vendor interface for PASN offload to userspace
809fb96fa Add a vendor attribute to configure concurrency policy for AP interface
a5754f531 Rename QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY
085a3fc76 EHT: Add 320 channel width support
bafe35df0 Move CHANWIDTH_* definitions from ieee80211_defs.h to defs.h
92f549901 tests: Remove the 80+80 vs. 160 part from wpa2_ocv_ap_vht160_mismatch
c580c2aec tests: Make OCV negative test error cases more robust
3c2ba98ad Add QCA vendor event to indicate driver recovery after internal failures
6b461f68c Set current_ssid before changing state to ASSOCIATING
8dd826741 QCA vendor attribute to configure direct data path for audio traffic
504be2f9d QCA vendor command support to get WLAN radio combinations
d5905dbc8 OCV: Check the Frequency Segment 1 Channel Number only on 80+80 MHz
Signed-off-by: David Bauer <mail@david-bauer.net>
Don't select channels designated for exclusive-indoor use when the
country3 element is set on outdoor operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
This matches the scheme used by other target packages and will avoid
confusion with any future version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
e065a7627a46 pex: update last query sent timestamp
6c888f897862 unet-cli: add stun server list editing support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
