Commit Graph

18507 Commits

Author SHA1 Message Date
Felix Fietkau
9aa0561534 hostapd: make it possible to update station airtime weights via ubus
This allows dynamic tuning based on other runtime information

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-07-12 13:31:40 +02:00
Daniel Golle
349e2b7e65
uboot-mediatek: several fixes for MT7622
* ! Behavior change !

   Old behavior: If the Reset button is held down during power-on
   do factory reset and try booting recovery from TFTP forever.
   If valid recovery is received via TFTP, write it to flash and boot.

   New behavior: If the Reset button is held down during power-on
   do factory reset, then try TFTP *once*, then try booting on-flash
   recovery, then keep trying via TFTP forever until a valid image is
   received.
   Only if there is no bootable recovery stored on flash, store the
   downloaded recovery. Then boot it.

 * Set loadaddr to 0x48000000 in order to allow booting images larger
   than ~47MB (reported by Oskari Lemmelä). Setting loadaddr to
   0x48000000 gives us 384MB on devices with 512MB RAM, which should be
   more than enough as a maximum size for uImage.FIT to be loaded.

 * Widely unify device-specific default environment in preparation to
   auto-generate it from parameters.

 * backport upstream commit fixing MBR/DOS partitioning

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-07-11 23:39:18 +01:00
Tee Hao Wei
0c721434ea ramips: add support for Linksys EA8100 v2
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0

This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1.

Installation:

Upload the generated factory image through the factory web interface.

(following part taken from EA7300 v2 commit message:)

This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.

Reverting to factory firmware:

Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.

With thanks to Tom Wizetek (@wizetek) for testing.

Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
2021-07-11 16:58:12 +02:00
Jo-Philipp Wich
c13d7c82aa iwinfo: update to latest Git HEAD and move device info into -data package
a0a0e02 iwinfo: rename hardware.txt to devices.txt

Also split common devices.txt (former hardware.txt) into a common
libiwinfo-data package to allow different libiwinfo versions to
coexist without file clashes.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2021-07-11 16:08:22 +02:00
Daniel Golle
f46a38a1ac
procd: update to git HEAD
2dcefbd jail: add support for cgroup devices as in OCI run-time spec

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-07-10 23:01:05 +01:00
Daniel Golle
315f52e0f3
lua: make it easier to detect host-built Lua
Install pkg-config file also for host-build, clean up Lua symlinks.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-07-10 22:13:24 +01:00
David Bauer
b0483b19f9 hostapd: add HE flag to get_clients
Expose the hostapd HE flag via ubus to indicate HE capable devices.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-07-06 02:27:06 +02:00
Martin Weinelt
cde154c871 hostapd: remove unused mac_buff allocation
Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
2021-07-06 02:26:44 +02:00
Martin Weinelt
398df62756 hostapd: report bssid, ssid and channel over ubus
Imports a function from iw to convert frequencies to channel numbers.

Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
[fix potential out of bounds read]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-07-06 02:26:38 +02:00
Kevin Darbyshire-Bryant
e4cfefa9fc dnsmasq: use local option for local domain parameter
'--local' is a synonym for '--server' so let's use '--local' in the
resultant config file for uci's 'local' instead of uci's local
parameter being turned into '--server'.  Slightly less confusion all
round.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-07-05 16:49:06 +01:00
Jo-Philipp Wich
5a1065758b iwinfo: build with nl80211 backend only and make shared
Drop support for building the obsolete broadcom-wl backend and always
forcibly enable the nl82011 support. This allows us to make the package
shared again since no target specific compilation is happening anymore.

This will solve various repository coherency issues related to unavailable
libiwinfo versions in the long run.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2021-07-02 18:49:21 +02:00
Petr Štetiar
8307da3dbd treewide: unmark selected packages nonshared
This partially reverts changes done in commit 72cc44958e ("treewide:
mark selected packages nonshared") as it removes the nonshared flag, but
keeps the PKG_RELEASE as the PKG_RELEASE bump while adding nonshared
flag was incorrect.

Unmark uci, ubus, libubox, lua, libnl-tiny and libjson-c as nonshared
packages as this fix attempt didn't worked out. Currently the
imagebuilder is broken again:

 openwrt-imagebuilder-21.02.0-rc3-ipq40xx-generic.Linux-x86_64$ make image PROFILE=avm_fritzbox-7530 PACKAGES=luci-ssl-openssl
 ...
 Collected errors:
  * pkg_hash_check_unresolved: cannot find dependency libiwinfo20210430 for luci-mod-status
  * pkg_hash_fetch_best_installation_candidate: Packages for luci-mod-status found, but incompatible with the architectures configured
  * pkg_hash_check_unresolved: cannot find dependency libiwinfo20210430 for rpcd-mod-iwinfo
  * pkg_hash_fetch_best_installation_candidate: Packages for rpcd-mod-iwinfo found, but incompatible with the architectures configured
  * satisfy_dependencies_for: Cannot satisfy the following dependencies for luci-ssl-openssl:
  * 	libiwinfo20210430
  * opkg_install_cmd: Cannot install package luci-ssl-openssl.

Everything because iwinfo's ABI was changed two times since rc3 release:

 +IWINFO_ABI_VERSION:=20210430
 +IWINFO_ABI_VERSION:=20210420

Since iwinfo is marked as nonshared, it wasn't built by phase2 builders, but
luci-mod-status was already updated 2 times since rc3 and was thus rebuilt by
phase2 builders:

 d1d452ed2fb3 luci-mod-status: don't set '-' hostname when creating static lease
 95b3633055c1 luci-mod-status: switch to html table for wlan channel analysis

So now luci-mod-status depends on libiwinfo20210430 but only
libiwinfo20210106 can be downloaded. This is first part of the fix, in
the upcoming commit Jo is going to remove nonshared flag from iwinfo
package as well.

References: https://lists.infradead.org/pipermail/openwrt-devel/2021-July/035736.html
References: https://lists.infradead.org/pipermail/openwrt-devel/2021-July/035741.html
Acked-by: Jo-Philipp Wich <jo@mein.io>
Reported-by: Nick Hainke <vincent@systemli.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-07-02 18:12:15 +02:00
Arjun AK
89ef883b92 package/comgt: Handle bind/unbind events
This script was expecting only add/remove events which has not been the
case since Kernel 4.12 (which added bind/unbind). Bind events were getting
treated as remove events which would cause hotplugged 3g modems to not
work.

More info:
https://lkml.org/lkml/2018/12/23/128
https://github.com/systemd/systemd/issues/8221

Signed-off-by: Arjun AK <arjunak234@gmail.com>
2021-07-02 11:09:57 +02:00
Felix Fietkau
3c57475085 ubus: update to the latest version
4fc532c8a55b ubusd: fix tx_queue linked list usage

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-30 21:58:51 +02:00
Felix Fietkau
de49957300 mac80211: backport fix for nl80211 control port tx (fixes FS#3857)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-30 19:09:31 +02:00
Felix Fietkau
8bb4437c01 mac80211: fix a regression in starting aggregation sessions on mesh interfaces
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-29 13:32:50 +02:00
Etan Kissling
ba5bd8e556 dnsmasq: distinct Ubus names for multiple instances
Currently, when using multiple dnsmasq instances they are all assigned
to the same Ubus instance name. This does not work, as only a single
instance can register with Ubus at a time. In the log, this leads to
`Cannot add object to UBus: Invalid argument` error messages.
Furthermore, upstream 3c93e8eb41952a9c91699386132d6fe83050e9be changes
behaviour so that instead of the log, dnsmasq exits at start instead.

With this patch, all dnsmasq instances are assigned unique names so that
they can register with Ubus concurrently. One of the enabled instances
is always assigned the previous default name "dnsmasq" to avoid breaking
backwards compatibility with other software relying on that default.
Previously, a random instance got assigned that name (while the others
produced error logs). Now, the first unnamed dnsmasq config section is
assigned the default name. If there are no unnamed dnsmasq sections the
first encountered named dnsmasq config section is assigned instead.

A similar issue exists for Dbus and was similarly addressed.

Signed-off-by: Etan Kissling <etan.kissling@gmail.com>
[tweaked commit message] dnsmasq was not crashing it is exiting
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-06-29 11:27:26 +01:00
Bob Cantor
e8b5429609 base-files: wifi: tidy up the reconf code
commit 5edbd390d321532d9a697d6895a1a7c71c40bd5d rearranged the
"wifi up" code.

This commit tidies up the "wifi reconf" code so as to
keep it aligned with the "wifi up" code.

branches affected: trunk, 21.02

Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
2021-06-28 17:24:15 +02:00
Bob Cantor
b82cc80713 base-files: wifi: swap the order of some ubus calls
"/sbin/wifi up" makes three ubus calls:
1. ubus call network reload
2. ubus call network.wireless down
3. ubus call network.wireless up

The first and third ubus calls call drv_mac80211_setup,
while the second ubus call triggers wireless_device_setup_cancel,
so the call sequence becomes,

1. drv_mac80211_setup
2. wireless_device_setup_cancel
3. drv_mac80211_setup

This commit swaps the order of the first two ubus calls,
1. ubus call network.wireless down
2. ubus call network reload
3. ubus call network.wireless up

Consequently drv_mac80211_setup is only called once,
and two related bugs (#FS3784 and #FS3902) are no longer triggered
by /sbin/wifi.

branches affected: trunk, 21.02

Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
2021-06-28 17:24:11 +02:00
Bob Cantor
3933e29d1b mac80211: print an error if wifi teardown fails
drv_mac80211_teardown fails silently if the device to be torn down is
not defined.  This commit prints an error message.

branches affected: trunk, 21.02

Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
2021-06-28 17:24:11 +02:00
Bob Cantor
d515f6b6cd mac80211: always call wireless_set_data (FS#3784)
When wifi is turned off, drv_mac80211_teardown sometimes fails (silently)
because the device to be torn down is not defined.

This situation arises if drv_mac80211_setup was called twice when
wifi was turned on.

This commit ensures that the device to be torn down is always defined
in drv_mac80211_teardown.

Steps to reproduce:

1) Use /sbin/wifi to turn on wifi.
   uci set wireless.@wifi-iface[0].disabled=0
   uci set wireless.@wifi-device[0].disabled=0
   uci commit
   wifi

2) Use /sbin/wifi to turn off wifi.
   uci set wireless.@wifi-device[0].disabled=1
   uci commit
   wifi

3) Observe that wifi is still up.

branches affected: trunk, 21.02

Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
2021-06-28 17:24:11 +02:00
Bob Cantor
a29ab3b79a mac80211: fix no_reload logic (FS#3902)
If drv_mac80211_setup is called twice with the same wifi configuration,
then the second call returns early with error HOSTAPD_START_FAILED.
(wifi works nevertheless, despite the fact that setup is incomplete.  But
"ubus call network.wireless status" erroneously reports that radio0 is down.)

The relevant part of drv_mac80211_setup is,

if [ "$no_reload" != "0" ]; then
        add_ap=1
        ubus wait_for hostapd
        local hostapd_res="$(ubus call hostapd config_add "{\"iface\":\"$primary_ap\", \"config\":\"${hostapd_conf_file}\"}")"
        ret="$?"
        [ "$ret" != 0 -o -z "$hostapd_res" ] && {
                wireless_setup_failed HOSTAPD_START_FAILED
                return
        }
        wireless_add_process "$(jsonfilter -s "$hostapd_res" -l 1 -e @.pid)" "/usr/sbin/hostapd" 1 1
fi

This commit sets no_reload = 0 during the second call of drv_mac80211_setup.

It is perhaps worth providing a way to reproduce the situation
where drv_mac80211_setup is called twice.

When /sbin/wifi is used to turn on wifi,
   uci set wireless.@wifi-iface[0].disabled=0
   uci set wireless.@wifi-device[0].disabled=0
   uci commit
   wifi

/sbin/wifi makes the following ubus calls,
   ubus call network reload
   ubus call network.wireless down
   ubus call network.wireless up

The first and third ubus calls both call drv_mac80211_setup,
while the second ubus call triggers wireless_device_setup_cancel.
So the call sequence becomes,

   drv_mac80211_setup
   wireless_device_setup_cancel
   drv_mac80211_setup

In contrast, when LuCI is used to turn on wifi only a single call
is made to drv_mac80211_setup.

branches affected: trunk, 21.02

Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
2021-06-28 17:24:11 +02:00
Felix Fietkau
019eca1545 iwinfo: update to the latest version
c9b1672f5a83 nl80211: fix path compatibility issue

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-28 15:45:11 +02:00
Rui Salvaterra
d31783329b zram-swap: clean up the log messages
Remove redundant tags and name things more consistently.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[removed superflous dash]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-06-27 14:49:14 -10:00
Rui Salvaterra
7720de4194 zram-swap: set the zram swap priority to 100 by default
New swap devices are added in decreasing priority order, starting at -1. Make
sure the zram swap device has the highest priority, by default.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-06-27 14:44:28 -10:00
Alexey Dobrovolsky
88114f617a busybox: sysntpd: add trigger to reload server
sysntpd server becomes unavailable if the index of the bound
interface changes. So let's add an interface trigger to reload sysntpd.

This patch also adds the ability for the sysntpd script to handle
uci interface name from configuration.

Fixes: 4da60500ebd2 ("busybox: sysntpd: option to bind server to iface")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
2021-06-27 23:54:06 +02:00
Paul Spooren
adddfe5787 dante: move to packages.git
Rather than maintaining it in core, move it to packages.git where it's
maintained by a community.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-06-26 18:10:44 -10:00
Kevin Darbyshire-Bryant
76cc8a036c Revert "dnsmasq: Update to version 2.86test3"
This reverts commit 3628870015.

dnsmasq v2.86test3 has some issues with ubus, so is being reverted.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-06-26 20:31:29 +01:00
Kevin Darbyshire-Bryant
2a9d7ecd27 Revert "dnsmasq: add config option for connmark DNS filtering"
This reverts commit dea4bae7c2.

dnsmasq v2.86test3 has some issues with ubus and needs reverting, hence
this needs reverting.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-06-26 20:30:58 +01:00
Etan Kissling
dea4bae7c2 dnsmasq: add config option for connmark DNS filtering
This adds uci support to configure connmark based DNS filtering.

Signed-off-by: Etan Kissling <etan_kissling@apple.com>
(See https://lists.thekelleys.org.uk/pipermail/dnsmasq-discuss/2021q2/015151.html)
Signed-off-by: Etan Kissling <etan.kissling@gmail.com>
2021-06-26 13:28:47 +01:00
Etan Kissling
3628870015 dnsmasq: Update to version 2.86test3
Need this version to add config option for connmark DNS filtering.

Summary of upstream CHANGELOG:
* Handle DHCPREBIND requests in the DHCPv6 server code.
* Fix bug which caused dnsmasq to lose track of processes forked.
* Major rewrite of the DNS server and domain handling code.
* Revise resource handling for number of concurrent DNS queries.
* Improve efficiency of DNSSEC.
* Connection track mark based DNS query filtering.

Signed-off-by: Etan Kissling <etan.kissling@gmail.com>
2021-06-26 13:28:08 +01:00
Paul Spooren
56bdb6bb97 base-files: fix /tmp/TZ when zoneinfo not installed
The zoneinfo packages are not installed per default so neither
/tmp/localtime nor /tmp/TZ is generated.

This patch mostly reverts the previous fix and instead incooperates a
solution suggested by Jo.

Fixes "base-files: fix zoneinfo support " 8af62ed

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-06-24 20:00:20 -10:00
Rui Salvaterra
18c24a29f9 zram-swap: robustify mkswap/swapon/swapoff invocation
Instead of assuming /sbin contains the correct BusyBox symlinks, directly invoke
the busybox executable. The required utilities are guaranteed to be present,
since the zram-swap package selects them. Additionally, don't assume busybox
resides in /bin, rely on PATH to find it.

While at it, update the copyright year, use SPDX and switch to AUTORELEASE.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-06-24 15:24:52 -10:00
Felix Fietkau
1818b038d7 hostapd: add support for providing vendor specific IE elements
They can be added as hex digit strings via the 'vendor_elements' option

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-24 15:56:46 +02:00
Raphaël Mélotte
acdb7c38c6 hostapd: add default_disabled option to the supplicant
With the default configuration we generate, the supplicant starts
scanning and tries to connect to any open network when the interface
is enabled.

In some cases it can be desirable to prevent the supplicant from
scanning by itself. For example, if on the same radio an AP is
configured and an unconfigured STA is added (to be configured with
WPS), the AP might not be able to beacon until the STA stops
scanning.

In such a case, the STA configuration can still be required to set
specific settings (e.g. multi_ap_backhaul_sta) so it can't be set to
"disabled" in uci (because that would prevent the supplicant from
being run at all). The alternative is to add the "disabled" parameter
to the default network block in the supplicant configuration.

This patch adds a "default_disabled" setting in UCI which, when set,
adds the "disabled" parameter to the supplicant default network block.

Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
2021-06-23 14:52:16 -10:00
Rosen Penev
8af62ede18 base-files: fix zoneinfo support
The system init script currently sets /tmp/localinfo when zoneinfo is
populated. However, zoneinfo has spaces in it whereas the actual files
have _ instead of spaces. This made the if condition never return true.

Example failure when removing the if condition:

/tmp/localtime -> /usr/share/zoneinfo/America/Los Angeles

This file does not exist. America/Los_Angeles does.

Ran through shfmt -w -ci -bn -sr -s

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-06-23 14:10:27 -10:00
Luiz Angelo Daros de Luca
fe6b9b0588 base-files: bring up vlan interface too
Vlan subinterface was never brought up when using vlan-based preinit network.
Tested forcing ifname="" before preinit_ip() on a Tp-Link Archer C5v4.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2021-06-22 23:23:00 +02:00
Hauke Mehrtens
790561d510 base-files: failsafe: Remove the VLAN modifier from interface name
Some interfaces have a VLAN modifier like :t in lan1:t, this modifier
should be removed from the interface before calling preinit_ip_config().

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-06-22 23:23:00 +02:00
Hauke Mehrtens
467cd378db base-files: failsafe: Fix IP configuration
Adapt the preinit_config_board() to the board.json network changes. It
now looks for the device and the ports variables to configure the LAN
network.

This works with swconfig configurations.

Fixes: FS#3866
Fixes: d42640e389 ("base-files: use "ports" array in board.json network for bridges")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
2021-06-22 23:23:00 +02:00
Aleksander Jan Bajkowski
c1927f4108 kernel: crypto: limit crypto-hw-hifn-795x to devices with pci support
CONFIG_CRYPTO_DEV_HIFN_795X depends on PCI. This driver only makes sense on
devices with pci support.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-06-22 23:23:00 +02:00
Timo Sigurdsson
bf98faaac8 hostapd: make wnm_sleep_mode_no_keys configurable
In the aftermath of the KRACK attacks, hostapd gained an AP-side workaround
against WNM-Sleep Mode GTK/IGTK reinstallation attacks. WNM Sleep Mode is not
enabled by default on OpenWrt, but it is configurable through the option
wnm_sleep_mode. Thus, make the AP-side workaround configurable as well by
exposing the option wnm_sleep_mode_no_keys. If you use the option
wpa_disable_eapol_key_retries and have wnm_sleep_mode enabled, you might
consider using this workaround.

Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
2021-06-22 11:10:06 -10:00
Karel Kočí
cc7316d1e9 base-files: fix enabled for services with only STOP
There are services that have only STOP value set. They are executed only
on shutdown and it is common to use them for system cleanup. There is
one such service shipped directly with base-files, it is 'umount'. Those
work the same way as those with START but enabled does not report them
as enabled although it should have as they can be enabled and disabled
as any other service.

This also changes check from check for executable to check for symbolic
link. The implementation depends on those being links to service file
and it is much cleaner and direct to check for them being links.

Signed-off-by: Karel Kočí <karel.koci@nic.cz>
2021-06-22 09:45:27 -10:00
Rafał Miłecki
0b2c1997e9 bcm63xx-cfe: update to the latest master
e5050f3 linksys: ea9500-v2: add cferam file

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-06-22 13:27:41 +02:00
Timo Sigurdsson
85ce590705 hostapd: fix handling of the channel utilization options
Commit 0a7657c ("hostapd: add channel utilization as config option") added the
two new uci options bss_load_update_period and chan_util_avg_period. However,
the corresponding "config_add_int" calls for these options weren't added, so
attempting to actually use these options and change their values is bound to
fail - they always stay at their defaults. Add the missing code to actually
make these options work.

Fixes: 0a7657c ("hostapd: add channel utilization as config option")
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
2021-06-21 19:04:06 -10:00
Timo Sigurdsson
9f09c1936a hostapd: make country3 option configurable
The country3 option in hostapd.conf allows the third octet of the country
string to be set. It can be used e.g. to indicate indoor or outdoor use (see
hostapd.conf for further details). Make this option configurable but optional
in OpenWrt.

Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
2021-06-21 19:02:33 -10:00
Karel Kočí
219e17a350 ustream-ssl: variants conflict with each other
This adds conflicts between variants of libustream pacakge.
They provide the same file and thus it should not be possible to install
them side by side.

Signed-off-by: Karel Kočí <karel.koci@nic.cz>
2021-06-21 18:48:03 -10:00
Dirk Neukirchen
2c9537e274 grub2: update to 2.06
-300-CVE-2015-8370.patch is upstreamed with different code
(upstream id: 451d80e52d851432e109771bb8febafca7a5f1f2)

- fixup OpenWrts setup_root patch

compile tested: x86_64,i386
runtime tested: VM x86_64,VM i386

- booted fine
- grub-editenv worked

Signed-off-by: Dirk Neukirchen <plntyk.lede@plntyk.name>
2021-06-21 09:02:26 -10:00
Chris Blake
f1e41155c9 kernel/modules: make sure igb loads at boot
Without loading the igb at boot, the recovery wouldn't have
network available. All network drivers should be loaded before
etc/board.d/02_network is called. Note that other network drivers
already have this set, such as tg3.

Fixes: 7e0e5110bc ("kernel: add igb kernel module")
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2021-06-21 08:38:07 -10:00
Florian Eckert
92ac2a20eb uci: add uci_revert function
Add missing uci_revert shell function wrapper.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2021-06-21 08:36:03 -10:00
Michael Yartys
f0f1d68d52 ath10k-ct: fix typo in Makefile
Add forgotten colon to Makefile.

Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
2021-06-21 08:34:39 -10:00
Perry Melange
23c3bab920 qos-scripts: add ifbN device before setting the link up
commit 50413e1ec8 replaced ifconfig
with ip.  In order to set a link state to up, the interface needs
to be added first.

Fixes: FS#3754

Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
[Add Fixes tag]
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2021-06-21 09:18:33 +02:00
Michael Yartys
b9b4aef4f2 hostapd: add support for setting sae_pwe
Make it possible to specify the SAE mechanism for PWE derivation. The
following values are possible:

0 = hunting-and-pecking loop only
1 = hash-to-element only
2 = both hunting-and-pecking loop and hash-to-element enabled

hostapd currently defaults to hunting-and-pecking loop only.

Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
2021-06-20 15:42:52 -10:00
Florian Eckert
40f533b73e base-files: redirect kill ouptut for ash, telnetd and dropbear
If one of the programmes is not running, then we see the following
output in the logs.

`killall: telnetd: no process killed`

To ensure that the log is clean, redirect the output to /dev/null

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2021-06-20 15:15:32 -10:00
Florian Eckert
d8bfcc59b0 base-files: remove unused vn and _vn function
The remaining vn calls have been ported to v.
Therefore, these functions are no longer needed and will be removed.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2021-06-20 15:15:32 -10:00
Florian Eckert
42d78fedfb base-files: change logging for upgrade on stage2
Remove vn call in favour of v call. This commit serves as preparation
for removing the vn function call.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2021-06-20 15:15:32 -10:00
Florian Eckert
bb2b7156a4 base-files: add syslog logging for v function
The logging output should not only be displayed in the calling shell
session but also in the syslog. A sysupgrade and a configuration
import, export can thus be traced in the syslog.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2021-06-20 15:15:32 -10:00
Chuck Fan
d374e2cdb4 base-files: upgrade: use zcat command provided by busybox
Calling `switch_to_ramfs()` will not copy the gzip executable
(/bin/gzip) to ramfs, but `/bin/zcat` will call `/bin/gzip` when
package gzip is installed, instead of the busybox-supplied zcat.
This will cause `zcat` to fail to find `gzip`, then cause the
sysupgrade to fail. Adding the `busybox` prefix here will solve
the problem.

Signed-off-by: Chuck Fan <fanck0605@qq.com>
2021-06-20 14:19:54 -10:00
Sergey Ponomarev
bffee5ea19 busybox: disable bzip2
bzip2 adds about 8kb of size. For tiny builds it's often disabled.
It's not directly used by stock OpenWrt programs.
Kernel images compressed with bzip2 are also not fully supported.

Signed-off-by: Sergey Ponomarev <stokito@gmail.com>
[fix \ indention]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-06-20 14:17:49 -10:00
Dobroslaw Kijowski
bb2ac5a33b hostapd: stop advertising 11w feature
This is a follow up of 1a9b896d ("treewide: nuke DRIVER_11W_SUPPORT").
LuCI commit ab010406 ("luci-mod-network: skip check for 802.11w feature")
skips check of the 11w feature [1]. Now advertising it in hostapd is
superfluous so stop doing it.

[1]: https://github.com/openwrt/luci/pull/4689

Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
[remove outdated PKG_RELEASE bump and update to SPDX]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-06-20 14:11:30 -10:00
Martin Schiller
2c6c1501af uhttpd: make organization (O=) of the cert configurable via uci
Make the organization (O=) of the cert configurable via uci. If not
configured, use a combination of "OpenWrt" and an unique id like it was
done before.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-06-20 13:50:36 -10:00
李国
e4723755f2 grub2: pass compilation parameters more accurately
In order for the grub2 boot-related code to compile normally, we have
made many adjustments to the compilation parameters. These adjustments
are not necessary for tools-related code. We apply these parameter
adjustments only to the boot-related code.

Signed-off-by: 李国 <uxgood.org@gmail.com>
2021-06-20 13:34:27 -10:00
李国
ca94104136 grub2: make grub2 tools built in a separate variant
grub2 boot-related code and tools-related code may require different
compilation parameters. We split them into different variants for
compilation, so that we can accurately pass the required parameters and
avoid causing problems.

Signed-off-by: 李国 <uxgood.org@gmail.com>
2021-06-20 13:31:09 -10:00
李国
5876d6a62f grub2: make grub2-bios-setup as a separate package
The grub2 and grub2-efi packages should only contain boot-related code.
grub-bios-setup is the same as grub-editenv, they are both grub2 tools
and should be placed in a separate package.

Signed-off-by: 李国 <uxgood.org@gmail.com>
[use AUTORELEASE and update to SPDX]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-06-20 13:23:42 -10:00
Rosen Penev
3dabb62581 treewide: remove PKG_INSTALL from CMake packages
It's already default with cmake.mk

Found with:

git grep PKG_INSTALL\: | cut -d ':' -f 1 | sort -u > ins
git grep cmake.mk | cut -d ':' -f 1 > cmake
comm -1 -2 ins cmake

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-06-19 20:44:59 -10:00
Rosen Penev
2e745e9be6 treewide: remove BUILD_PARALLEL from CMake packages
It's already default. The only exception is mt76 which has Ninja
disabled.

Found with:

git grep BUILD_PARALLEL | cut -d ':' -f 1 | sort -u > par
git grep cmake.mk | cut -d ':' -f 1 > cmake
comm -1 -2 par cmake

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-06-19 20:44:59 -10:00
Felix Fietkau
89c9ccc3b2 mac80211: fix an issue with wds links on 802.11ax devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-19 12:17:09 +02:00
Felix Fietkau
165a026364 mac80211: remove extra patch accidentally added during rebase
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-18 09:55:51 +02:00
Felix Fietkau
53b6783907 mac80211: remove patches stripping down crypto support
Use of WPA3 and things like FILS is getting much more common, and platforms
that can't affort the extra kilobytes for this code are fading away.
Let's not hold back modern authentication methods any longer

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-18 09:52:35 +02:00
Felix Fietkau
a603e82dd3 mac80211: system hang caused by deferring calls into minstrel to dequeue
Move the aggregation check to mac80211

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-17 18:25:35 +02:00
Felix Fietkau
db9784bedd mac80211: fix minstrel sample time check
We need to skip sampling if the next sample time is after jiffies, not before.
This patch fixes an issue where in some cases only very little sampling (or none
at all) is performed, leading to really bad data rates

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-17 12:41:06 +02:00
Felix Fietkau
a0f97d8f9c mac80211: select iwinfo
Since iwinfo is now used in the core scripts, it needs to be present on the system

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-17 12:40:43 +02:00
Felix Fietkau
49ef4dbee5 mac80211: fix processing HE capabilities (FS#3871)
Use the right argument to fix setting unsupported capabilities to 0

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-17 12:40:43 +02:00
Daniel Golle
3d026d2425 ugps: start also in case device is absent
Don't bail out from init script in case the GPS device is missing.
Some modems take time to come up, and some people may use things like
'kplex' to feed ugpsd. Hence it is better to always start ugpsd
unconditionally and let procd's respawn take care of retrying.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-06-15 11:48:20 +01:00
Rafał Miłecki
946019637e base-files: fix typo in config_generate MAC check
Fixes: 8d8eb9d13fc6 ("base-files: set MAC for bridge ports (devices) instead of bridge itself")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-06-14 22:29:49 +02:00
Rafał Miłecki
c8d8eb9d13 base-files: set MAC for bridge ports (devices) instead of bridge itself
This restores the original config_generate behaviour. With MAC set for
bridged devices the bridge automatically gets its MAC adjusted (it picks
the lowest MAC of bridged devices).

This fixes confusing interfaces setup (bridge ports not having custom
MAC assigned).

Reported-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Fixes: e002179a6d ("base-files: simplify setting device MAC")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-06-14 20:24:46 +02:00
Hauke Mehrtens
da86064611 opkg: update to git HEAD
1bf042d libopkg: pkg_hash: print unresolved dependencies

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-06-13 23:58:15 +02:00
Hauke Mehrtens
65b0fe293a opkg: Fix download over git
Set the PKG_SOURCE_URL using a lazy set to allow evaluating
$(PROJECT_GIT) later. Without this change PKG_SOURCE_URL is evaluated
immediately, before PROJECT_GIT is defined and the download over git is
not working.

Fixes: 6687a2483a ("opkg: use $(PROJECT_GIT), $(AUTORELEASE) and SPDX")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-06-13 23:58:15 +02:00
Hannu Nyman
72cc44958e treewide: mark selected packages nonshared
Mark uci, ubus, libubox, lua, libnl-tiny and libjson-c
as nonshared packages. This helps to keep coherent dependencies
if these ABI versioned packages are later updated.

Before this commit it is possible to get missing dependencies
in target-specific nonshared packages (like iwinfo) that depend
on these shared ABI versioned packages. If these are later updated
and rebuilt, only the new ABI version will be available for download,
while the target-specific packages in releases continue to depend on
the old ABI version.

After this commit the packages are built along the other nonshared
packages by the phase1 images buildbot and will be available at the
target/ download directories instead of packages/base dir. That will
help to keep a coherent set available.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2021-06-13 23:58:15 +02:00
Hans Dedecker
6ed0ddde05 odhcpd: update to latest git HEAD
564d25e config: fix ra_flags none setting

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2021-06-13 22:28:40 +02:00
Michael Pratt
b118aba8cb base-files: upgrade: use procd to kill managed daemons
These processes are managed by procd and set to start again when killed
via the procd instance parameter "respawn" being set during init.

Example:
procd_set_param respawn 3600 1 0

When they are killed manually during sysupgrade,
they are started again in 5 seconds or less, depending on
how the "respawn" parameter is set.

Use procd through ubus to disable the instances that respawn them,
however, allow dnsmasq, netifd, and logd to restart for remote logging.

Properly closing all these processes increases free memory by about 3 MB,
which should help low memory devices upgrade without crashing.

For very low memory devices (set to 32 MB for now)
also kill dnsmasq, netifd, and logd for an additional 3 MB of free memory.

Also, bump sleep values to allow at least 10 seconds
for network interfaces and daemons
to come up after they are killed and restarted
before caches are dropped.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-06-12 13:59:27 -10:00
Rosen Penev
09de28090c package: fix cmake packages build with ninja
+= is needed for CMAKE_OPTIONS.

mt76 needs Ninja disabled as the kernel stuff uses normal make.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-06-12 10:46:39 +02:00
Felix Fietkau
f2c6d892ca mac80211: add support for 802.3 encap offload with software rate control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-12 10:46:39 +02:00
Felix Fietkau
7dd8829ef9 mac80211: improve rate control performance
Call rate control handler after intermediate queueuing

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-12 10:46:39 +02:00
Tianling Shen
52dc7995f7 uboot-rockchip: add NanoPi R4S support
Add support for the FriendlyARM NanoPi R4S.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2021-06-10 10:34:44 +02:00
Felix Fietkau
e1d57d4d43 mac80211: rely on iwinfo for phy->path and path->phy lookups
This avoids inconsistencies from having multiple implementations do the same thing

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-10 10:15:39 +02:00
Felix Fietkau
6e8475bbd0 iwinfo: update to the latest version
aa0e3c4bbe12 iwinfo: nl80211: add support for printing the device path for a phy
dd6d6d2dec35 iwinfo: nl80211: use new path lookup function for nl80211_phy_idx_from_uci_path
268bb26d2e2a iwinfo: nl80211: support looking up phy by path=.. and macaddr=...
c0414642fead iwinfo: nl80211: fix typo

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-10 10:15:39 +02:00
Tomas Lara
4413537430 linux-firmware: update to 20210511
git log --pretty=oneline --abbrev-commit 20201118..20210511

7685cf4 (HEAD, tag: 20210511) nvidia: Update Tegra194 XUSB firmware to v60.09
cf32752 nvidia: Update Tegra186 XUSB firmware to v55.18
cb8ca82 nvidia: Update Tegra210 XUSB firmware to v50.26
f99d6a1 linux-firmware: update firmware for mhdp8546
ecdfcf8 Merge branch 'adlp_dmc_firmware' of git://anongit.freedesktop.org/drm/drm-firmware into main
547b202 Merge https://github.com/suraj714/linux-firmware-venus into main
3d32f21 i915: Add ADL-P DMC Support
3f23f51 amdgpu: add new polaris 12 MC firmware
a2565bb firmware: nvidia: Add VIC firmware for Tegra194
17ec2a5 qcom: add gpu firmwares for sc7280
b653cf4 Merge https://github.com/pkshih/linux-firmware into main
2a96c08 brcm: Add a link to enable khadas VIM2's WiFi
ffc64a2 rtw89: 8852a: update fw to v0.13.8.0
3e3497c rtl_bt: Update RTL8852A BT USB firmware to 0xD9A8_7893
c7b11ed qcom: Add venus firmware files for VPU-2.0
2f4f0f8 rtw89: 8852a: update fw to v0.13.8.0
fa0efef linux-firmware: Update firmware file for Intel Bluetooth AX210
9be3daa linux-firmware: Update firmware file for Intel Bluetooth 9560
687d64a linux-firmware: Update firmware file for Intel Bluetooth 9260
a7f1249 linux-firmware: Update firmware file for Intel Bluetooth AX200
47650a0 linux-firmware: Update firmware file for Intel Bluetooth AX201
195ecf1 linux-firmware: Intel BT 7265: Fix Security Issues
4116d72 linux-firmware: Update firmware file for Intel Bluetooth 8265
ca83c73 qcom: update venus firmware files for v5.4
1334578 Merge branch 'mrvl-prestera' of https://github.com/PLVision/linux-firmware into main
16052e4 mrvl: prestera: Add Marvell Prestera Switchdev firmware 3.0 version
bdf929d rtw88: 8822c: Update normal firmware to v9.9.9
0b558e8 brcm: add missing symlink for Pi Zero W NVRAM file
cfa004c amdgpu: update arcturus firmware from 21.10
d5567c5 amdgpu: update navy flounder firmware from 21.10
ef5ea5d amdgpu: update sienna cichlid firmware from 21.10
f35700f amdgpu: update vega20 firmware from 21.10
1be98f1 amdgpu: update picasso firmware from 21.10
fee0497 amdgpu: update navi14 firmware from 21.10
15003b0 amdgpu: update green sardine firmware from 21.10
64555fb amdgpu: update vega12 firmware from 21.10
eb07276 amdgpu: update navi12 firmware from 21.10
e36c82a amdgpu: update vega10 firmware from 21.10
4a5eaa2 amdgpu: update renoir firmware from 21.10
65eb326 amdgpu: update navi10 firmware from 21.10
8bdca03 amdgpu: update raven2 firmware from 21.10
c9e44ca amdgpu: update raven firmware from 21.10
bc3e610 rtl_nic: add new firmware for RTL8153 and RTL8156 series
8528618 Merge branch 'for-upstream' of git://git.chelsio.net/pub/git/linux-firmware into main
940b7f4 cxgb4: Update firmware to revision 1.25.4.0
f66adc3 Merge branch 'main' of gitolite.kernel.org:/pub/scm/linux/kernel/git/maks/linux-firmware into main
f350e91 Merge https://github.com/rjliao-qca/qca-btfw into main
9bc1bcc Merge https://github.com/Netronome/linux-firmware into main
2f30708 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2438
393f272 brcm: Link CM4's WiFi firmware with DMI machine name.
73144e0 linux-firmware: Update firmware file for Intel Bluetooth AX201
8ab7aba amdgpu: update navi14 smc firmware
4fe6e53 amdgpu: update navi10 SMC firmware
c296849 QCA: Update Bluetooth firmware for QCA6174
d6a18e9 WHENCE: link to similar config file for rtl8821a support
6c419ae nfp: update Agilio SmartNIC flower firmware to rev AOTC-2.14.A.6
af1ca28 amdgpu: add arcturus firmware
0dd245d Merge branch 'sm8250-new-fw' of https://github.com/lumag/linux-firmware into main
55cab07 rtl_bt: Add rtl8723bs_config-OBDA0623.bin symlink
2548d06 brcm: Add nvram for the Chuwi Hi8 (CWI509) tablet
e45c137 brcm: Add nvram for the Predia Basic tablet
d8fa0cf qcom: sm8250: update remoteproc firmware
84af0e0 qcom: update a650 firmware files
3f026a2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x59A_76A3
c82cb46 amdgpu: update sienna cichlid firmware for 20.50
24fe696 amdgpu: update vega20 firmware for 20.50
e05d197 amdgpu: update picasso firmware for 20.50
76d07cd amdgpu: update navi14 firmware for 20.50
b2fc037 amdgpu: update vega12 firmware for 20.50
25451a4 amdgpu: update navi12 firmware for 20.50
b938597 amdgpu: update vega10 firmware for 20.50
2542ba7 amdgpu: update renoir firmware for 20.50
b55d063 amdgpu: update navi10 firmware for 20.50
1a62f28 amdgpu: update raven2 firmware for 20.50
4df488f amdgpu: update raven firmware for 20.50
a29bdb2 amdgpu: add initial support for navy flounder
3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210
9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200
c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201
5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main
b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6
5a2fd63 iwlwifi: add new FWs from core59-66 release
4f54906 iwlwifi: update 9000-family firmwares
11b7607 iwlwifi: update 7265D firmware
e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main
5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406
58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921)
e576a1b rtw89: 8852a: add firmware v0.9.12.2
048a7cb WHENCE: add missing symlink for BananaPi M3
aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config
58825f7 brcm: Fix Raspberry Pi 4B NVRAM file
520f71b silabs: add new firmware for WF200
f7915a0 amdgpu: add initial firmware for green sardine
80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5
b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main
66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main
cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304
391fd50 linux-firmware: add firmware for MT7921
c5e3240 rtw88: RTL8821C: Update firmware to v24.8
d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210
3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200
13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201
348d8a9 i915: Add DMC v2.01 for ADL-S
f33f1f7 i915: Add HuC v7.7.1 for DG1
6a422f5 i915: Add GuC v49.0.1 for DG1
df822a8 qcom: Add venus firmware files for VPU-1.0
11a1db1 qcom: Add SM8250 Compute DSP firmware
e55248b qcom: Add SM8250 Audio DSP firmware
da74cc6 qcom: add firmware files for Adreno a650
0578970 brcm: Link RPi4's WiFi firmware with DMI machine name.
d528862 brcm: Add NVRAM for Vamrs 96boards Rock960
870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes
a28a590 cypress: Fix link direction
060ad8b cypress: Link the new cypress firmware to the old brcm files
0f0aefd brcm: remove old brcm firmwares that have newer cypress variants
f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB
7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253
e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip
ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644
646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work
28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210
23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200
2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201
94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560
27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260
5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main
aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main
d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main
63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge
0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6
1a08ec9 QCA : Updated firmware files for WCN3991
7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main
7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210
5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210
c487f7d i915: Add GuC firmware v49.0.1 for all platforms
d9ffb07 i915: Remove duplicate KBL DMC entry
b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018
bc9cd0b linux-firmware: Update AMD SEV firmware
54c797a amdgpu: add sienna cichlid firmware for 20.45
1340e9c amdgpu: update vega20 firmware for 20.45
b260c9c amdgpu: update vega12 firmware for 20.45
d683bd5 amdgpu: update vega10 firmware for 20.45
7c81cc2 amdgpu: update renoir firmware for 20.45
3619e57 amdgpu: update navi14 firmware for 20.45
68ce0fb amdgpu: update navi12 firmware for 20.45
e889b80 amdgpu: update navi10 firmware for 20.45
f4edc15 amdgpu: update raven2 firmware for 20.45
e71210f amdgpu: update raven firmware for 20.45

Signed-off-by: Tomas Lara <tl849670@gmail.com>
[rebased; removed brcmfmac changes due to removed firmware]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-06-08 00:38:41 +02:00
Robert Marko
1412424fc5 ethtool: update to version 5.12
Update ethtool to newly released 5.12 version.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-06-08 00:37:52 +02:00
Daniel Golle
3a8b75b569 ugps: update to git HEAD
86ee86e nmea: parse $GPZDA sentences for date/time
 8e12414 nmea: parse $GPGLL sentences for position
 5e88403 ubus: display only available information

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-06-07 23:13:18 +01:00
Adrian Schmutzler
482e65a16d uboot-kirkwood: refresh patches
This is only cosmetic, but the next one adding a patch here would
have to do it anyway, and thus will get a smaller diff for review
now.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-06 19:06:29 +02:00
BERENYI Balazs
03d66d6b8f kirkwood: Add support for Sheevaplug
Globalscale SheevaPlug:
* Marvell Kirkwood 88F6281
* 512 MB SDRAM
* 512 MB Flash
* Gigabit Network
* USB 2.0
* SD slot
* Serial console

The device is supported in mainline uboot/linux the commit adds only
some openwrt config for building an image.

Installation:
1 - Update uboot:
setenv ipaddr '192.168.0.111'
setenv serverip '192.168.0.1'
tftpboot u-boot.kwb
nand erase 0x0 0x100000
nand write 0x800000 0x0 0x100000
reset
2 - Install OpenWRT:
setenv ethaddr 00:50:43:01:xx:xx
saveenv
setenv ipaddr '192.168.0.111'
setenv serverip '192.168.0.1'
tftpboot openwrt-kirkwood-globalscale_sheevaplug-squashfs-factory.bin
nand erase.part ubi
nand write 0x800000 ubi 0x600000
reset

Signed-off-by: BERENYI Balazs <balazs@wee.hu>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
[add vendor name for uboot-kirkwood, merge patches, copy to 5.10,
add AUTORELEASE for uboot-kirkwood, refresh patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-06 19:05:07 +02:00
Hauke Mehrtens
04a260911c mac80211: Update to backports-5.10.42
The removed patches were integrated upstream.

The brcmf_driver_work workqueue was removed in brcmfmac with kernel
5.10.42, the asynchronous call was covered to a synchronous call. There
is no need to wait any more.
This part was removed manually from this patch:
brcm/860-brcmfmac-register-wiphy-s-during-module_init.patch

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-06-06 17:49:40 +02:00
Felix Fietkau
3c46ba053d mt76: update to the latest version
Add mt7915e dependency on kmod-thermal

22b690334c0f mt76: mt7915: do not fail if the cooling device could not be registered

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-06 10:55:09 +02:00
Josef Schlehofer
ff2bb16730 linux-firmware: update to version 20210315 and trim down broadcom FW
In there linux-firmware repository located in kernel, there were removed old
broadcom firmware [1] as they seem to be likely vulnerable to KrØØk vulnerability
(CVE-2019-15126), because Cypress released new versions and superseded
by it.

In OpenWrt, there is Makefile for cypress-firmware, which already provides
the same named packages like it was in linux-firmware. For example, cypress-firmware-43455-sdio
provides brcmfmac-firmware-43455-sdio [2].

Changelog between 2020118 and 20210315:
3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210
9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200
c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201
5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main
b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6
5a2fd63 iwlwifi: add new FWs from core59-66 release
4f54906 iwlwifi: update 9000-family firmwares
11b7607 iwlwifi: update 7265D firmware
e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main
5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406
58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921)
e576a1b rtw89: 8852a: add firmware v0.9.12.2
048a7cb WHENCE: add missing symlink for BananaPi M3
aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config
58825f7 brcm: Fix Raspberry Pi 4B NVRAM file
520f71b silabs: add new firmware for WF200
f7915a0 amdgpu: add initial firmware for green sardine
80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5
b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main
66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main
cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304
391fd50 linux-firmware: add firmware for MT7921
c5e3240 rtw88: RTL8821C: Update firmware to v24.8
d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210
3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200
13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201
348d8a9 i915: Add DMC v2.01 for ADL-S
f33f1f7 i915: Add HuC v7.7.1 for DG1
6a422f5 i915: Add GuC v49.0.1 for DG1
df822a8 qcom: Add venus firmware files for VPU-1.0
11a1db1 qcom: Add SM8250 Compute DSP firmware
e55248b qcom: Add SM8250 Audio DSP firmware
da74cc6 qcom: add firmware files for Adreno a650
0578970 brcm: Link RPi4's WiFi firmware with DMI machine name.
d528862 brcm: Add NVRAM for Vamrs 96boards Rock960
870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes
a28a590 cypress: Fix link direction
060ad8b cypress: Link the new cypress firmware to the old brcm files
0f0aefd brcm: remove old brcm firmwares that have newer cypress variants
f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB
7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253
e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip
ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644
646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work
28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210
23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200
2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201
94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560
27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260
5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main
aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main
d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main
63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge
0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6
1a08ec9 QCA : Updated firmware files for WCN3991
7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main
7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210
5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210
c487f7d i915: Add GuC firmware v49.0.1 for all platforms
d9ffb07 i915: Remove duplicate KBL DMC entry
b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018
bc9cd0b linux-firmware: Update AMD SEV firmware
54c797a amdgpu: add sienna cichlid firmware for 20.45
1340e9c amdgpu: update vega20 firmware for 20.45
b260c9c amdgpu: update vega12 firmware for 20.45
d683bd5 amdgpu: update vega10 firmware for 20.45
7c81cc2 amdgpu: update renoir firmware for 20.45
3619e57 amdgpu: update navi14 firmware for 20.45
68ce0fb amdgpu: update navi12 firmware for 20.45
e889b80 amdgpu: update navi10 firmware for 20.45
f4edc15 amdgpu: update raven2 firmware for 20.45
e71210f amdgpu: update raven firmware for 20.45

[1] https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=0f0aefd733f70beae4c0246edbd2c158d5ce974c

[2] eeda8652f1/package/firmware/cypress-firmware/Makefile (L124)

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2021-06-06 00:26:13 +02:00
Tomasz Maciej Nowak
e9c9b5ec72 kernel: package Synopsys Designware PCI to I2C controller
This is present on Roqos Core RC10 and needed to control LED matrix.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2021-06-06 00:26:13 +02:00
Kuan-Yi Li
2fdb7053f9 kernel: usb: add kmod-usb-gadget-ncm
Add kernel module package for USB Network Control Model (NCM) Gadget
support.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2021-06-06 00:26:13 +02:00
Michael Yartys
2e10ed925e ath10k-ct: update to latest version
Changelog:
- ath10k-ct: Add security fixes.
- ath10k-ct: Add 5.12 kernel version.
- ath10k-ct: Fix the beacon/mcast/bcast override issue
- ath10k-ct 5.7: Fix setting mcast/bcast/beacon rate from debugfs.
- ath10k-ct: Add 5.11 driver.

Delete upstreamed patch and refresh the rest. Also, use the opportunity to
set PKG_RELEASE to $(AUTORELEASE).

Runtime-tested on ipq806x (Netgear R7800).

Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
2021-06-06 00:26:13 +02:00
Adrian Schmutzler
6bc4c0ae3e umbim: fix return value of proto_mbim_setup()
The variable name appears to be mistyped.

Suggested-by: Howard Chu <hyc@symas.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:39:14 +02:00
Adrian Schmutzler
01f29a0c72 umbim: fix whitespace issues
Make leading whitespaces consistent and remove trailing one.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:39:14 +02:00
Lauro Moreno
da8428d277 ipq806x: add support for Askey RT4230W REV6
This adds support for the Askey RT4230W REV6
(Branded by Spectrum/Charter as RAC2V1K)

At this time, there's no way to reinstall the stock firmware so don't install
this on a router that's being rented.

Specifications:

    Qualcomm IPQ8065
    1 GB of RAM (DDR3)
    512 MB Flash (NAND)
    2x Wave 2 WiFi cards (QCA9984)
    5x 10/100/1000 Mbps Ethernet (Switch: QCA8337)
    1x LED (Controlled by a microcontroller that switches it between red and
        blue with different patterns)
    1x USB 3.0 Type-A
    12V DC Power Input
    UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V
    Port settings are 115200n8

More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830
https://deviwiki.com/wiki/Askey_RAC2V1K

To check what revision your router is, restore one of these config backups
through the stock firmware to get ssh access then run
"cat /proc/device-tree/model".
https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17
The revision number on the board doesn't seem to be very consistent so that's
why this is needed. You can also run printenv in the uboot console and if
machid is set to 177d, that means your router is rev6.

Note: Don't install this if the router is being rented from an ISP. The defined
partition layout is different from the OEM one and even if you changed the
layout to match, backing up and restoring the OEM firmware breaks /overlay so
nothing will save and the router will likely enter a bootloop.

How to install:

Method 1: Install without opening the case using SSH and tftp

    You'll need:
    RAC2V1K-SSH.zip:
https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip
    initramfs and sysupgrade images

    Connect to one of the router's LAN ports

    Download the RAC2V1K-SSH.zip file and restore the config file that
corresponds to your router's firmware (If you're firmware is newer than what's
in the zip file, just restore the 1.1.16 file)

    After a reboot, you should be able to ssh into the router with username:
"4230w" and password: "linuxbox" or "admin". Run the following commannds
     fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as
it's in the same subnet as the server
     fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next
steps
     fw_setenv bootdelay 8
     fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq"

    Don't reboot the router yet.

    Install and set up a tftp server on your computer

    Set a static ip on the ethernet interface of your computer (use this for
serverip in the above commands)

    Rename the initramfs image to initramfs.bin, and host it with the tftp
server

    Reboot the router. If you set up everything right, the router led should
switch over to a slow blue glow which means openwrt is booted. If for some
reason the file doesn't get loaded into ram properly, it should still boot to
the OEM firmware.
    After openwrt boots, ssh into it and run these commands:
    fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts
 mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi
read 0x44000000 kernel 0x6e0000 && bootm"
    fw_setenv bootdelay 2

    After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.

Method 2: Install with serial access (Do this if something fails and you can't
boot after using method 1)

    You'll need:
    initramfs and sysupgrade images
    Serial access:
https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case

    Install and set up a tftp server

    Set a static ip on the ethernet interface of your computer

    Download the initramfs image, rename it to initramfs.bin, and host it with
the tftp server

    Connect the wan port of the router to your computer

    Interrupt U-Boot and run these commands:
    setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer)
    setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet)
    setenv bootcmd "setenv mtdids nand0=nand0 &&
set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware
&& ubi read 0x44000000 kernel 0x6e0000 && bootm"

    saveenv
    tftpboot initramfs.bin
    bootm

    After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.

Signed-off-by: Lauro Moreno <lmore377@gmail.com>
[add entry in 5.10 patch, fix whitespace issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:39:14 +02:00
Tee Hao Wei
b232680f84 ramips: add support for Linksys EA8100 v1
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0

This device is very similar to the EA7300 v1/v2 and EA7500 v2.

Installation:

Upload the generated factory image through the factory web interface.

(following part taken from EA7300 v2 commit message:)

This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.

Reverting to factory firmware:

Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.

With thanks to Leon Poon (@LeonPoon) for the initial bringup.

Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
[add missing entry in 10_fix_wifi_mac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:39:14 +02:00
Jonathan Sturges
6d23e474ad ramips: add support for Amped Wireless ALLY router and extender
Amped Wireless ALLY is a whole-home WiFi kit, with a router (model
ALLY-R1900K) and an Extender (model ALLY-00X19K).  Both are devices are
11ac and based on MediaTek MT7621AT and MT7615N chips.  The units are
nearly identical, except the Extender lacks a USB port and has a single
Ethernet port.

Specification:
- SoC: MediaTek MT7621AT (2C/4T) @ 880MHz
- RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI)
- FLASH: 128MB NAND (Winbond W29N01GVSIAA)
- WiFi: 2.4/5 GHz 4T4R
  - 2.4GHz MediaTek MT7615N bgn
  - 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch
- USB: 1x USB3 (Router only)
- BTN: Reset, WPS
- LED: single RGB
- UART:  through-hole on PCB.
   J1: pin1 (square pad, towards rear)=3.3V, pin2=RX,
   pin3=GND, pin4=TX.  Settings: 57600/8N1.

Note regarding dual system partitions
-------------------------------------

The vendor firmware and boot loader use a dual partition scheme.  The boot
partition is decided by the bootImage U-boot environment variable: 0 for
the 1st partition, 1 for the 2nd.

OpenWrt does not support this scheme and will always use the first OS
partition.  It will set bootImage to 0 during installation, making sure
the first partition is selected by the boot loader.

Also, because we can't be sure which partition is active to begin with, a
2-step flash process is used.  We first flash an initramfs image, then
follow with a regular sysupgrade.

Installation:

Router (ALLY-R1900K)
1) Install the flashable initramfs image via the OEM web-interface.
  (Alternatively, you can use the TFTP recovery method below.)
  You can use WiFi or Ethernet.
  The direct URL is:  http://192.168.3.1/07_06_00_firmware.html
  a. No login is needed, and you'll be in their setup wizard.
  b. You might get a warning about not being connected to the Internet.
  c. Towards the bottom of the page will be a section entitled "Or
  Manually Upgrade Firmware from a File:" where you can manually choose
  and upload a firmware file.
  d: Click "Choose File", select the OpenWRT "initramfs" image and click
  "Upload."
2) The Router will flash the OpenWrt initramfs image and reboot.  After
  booting, LuCI will be available on 192.168.1.1.
3) Log into LuCI as root; there is no password.
4) Optional (but recommended) is to backup the OEM firmware before
  continuing; see process below.
5) Complete the Installation by flashing a full OpenWRT image.  Note:
  you may use the sysupgrade command line tool in lieu of the UI if
  you prefer.
  a.  Choose System -> Backup/Flash Firmware.
  b.  Click "Flash Image..." under "Flash new firmware image"
  c.  Click "Browse..." and then select the sysupgrade file.
  d.  Click Upload to upload the sysupgrade file.
  e.  Important:  uncheck "Keep settings and retain the current
      configuration" for this initial installation.
  f.  Click "Continue" to flash the firmware.
  g.  The device will reboot and OpenWRT is installed.

Extender (ALLY-00X19K)
1) This device requires a TFTP recovery procedure to do an initial load
  of OpenWRT.  Start by configuring a computer as a TFTP client:
  a. Install a TFTP client (server not necessary)
  b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6
  c. Connect the Ethernet to the sole Ethernet port on the X19K.
2) Put the ALLY Extender in TFTP recovery mode.
  a. Do this by pressing and holding the reset button on the bottom while
  connecting the power.
  b. As soon as the LED lights up green (roughly 2-3 seconds), release
  the button.
3) Start the TFTP transfer of the Initramfs image from your setup machine.
For example, from Linux:
tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin
4) The Extender will flash the OpenWrt initramfs image and reboot.  After
booting, LuCI will be available on 192.168.1.1.
5) Log into LuCI as root; there is no password.
6) Optional (but recommended) is to backup the OEM firmware before
  continuing; see process below.
7) Complete the Installation by flashing a full OpenWRT image.  Note: you
may use the sysupgrade command line tool in lieu of the UI if you prefer.
  a.  Choose System -> Backup/Flash Firmware.
  b.  Click "Flash Image..." under "Flash new firmware image"
  c.  Click "Browse..." and then select the sysupgrade file.
  d.  Click Upload to upload the sysupgrade file.
  e.  Important:  uncheck "Keep settings and retain the current
      configuration" for this initial installation.
  f.  Click "Continue" to flash the firmware.
  g.  The device will reboot and OpenWRT is installed.

Backup the OEM Firmware:
-----------------------

There isn't any downloadable firmware for the ALLY devices on the Amped
Wireless web site. Reverting back to the OEM firmware is not possible
unless we have a backup of the original OEM firmware.

The OEM firmware may be stored on either /dev/mtd3 ("firmware") or
/dev/mtd6 ("oem").  We can't be sure which was overwritten with the
initramfs image, so backup both partitions to be safe.

  1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware.
  2) Under "Save mtdblock contents," first select "firmware" and click
  "Save mtdblock" to download the image.
  3) Repeat the process, but select "oem" from the pull-down menu.

Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
  Follow the TFTP recovery steps for the Extender, and use the
  backup image.

* OpenWrt "Flash Firmware" interface:
  Upload the backup image and select "Force update"
  before continuing.

Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
2021-06-05 23:39:14 +02:00
Robert Marko
b126d9c3a3 ipq40xx: add netgear wac510 support
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.

For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>

Specifications:
SoC:        Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:        256 MiB
Flash1:     2 MiB Winbond W25Q16JV SPI-NOR
Flash2:     128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet:   Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
            WAN port active IEEE 802.3af/at PoE in
Wireless1:  Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2:  Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input:      (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs:       Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial:     Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
         The Serial settings are 115200-8-N-1.

Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.

In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.

Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.

Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm

Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:

Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[    1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.

Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[    2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[    2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-06-05 23:29:46 +02:00
Felix Fietkau
305c1b8d74 hostapd: configure inter-AP communication interface for 802.11r
In setups using VLAN bridge filtering, hostapd may need to communicate using
a VLAN interface on top of the bridge, instead of using the bridge directly

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-05 06:53:29 +02:00
Sven Eckelmann
9a172797e5 ath79: Add support for OpenMesh A40
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
  - eth0
    + Label: Ethernet 1
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as WAN interface
  - eth1
    + Label: Ethernet 2
    + AR8035 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + used as LAN interface
* 1x USB
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-06-05 01:17:11 +02:00
Sven Eckelmann
eaf2e32c12 ath79: Add support for OpenMesh A60
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
  - eth0
    + Label: Ethernet 1
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as WAN interface
  - eth1
    + Label: Ethernet 2
    + AR8031 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + used as LAN interface
* 1x USB
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-06-05 01:17:11 +02:00
Ansuel Smith
3394af677c mac80211: split ath patch in dedicated subdir
The ath patch number is already large and adding other patch for ath11k
will add more confusion with the patch numbering.
Since the support of ath11k based device is imminent, prepare the mac80211
ath patch dir and split it in the dedicated ath5k, ath9k, ath10k and ath11k
(empty for now).

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-06-04 22:44:40 +02:00
Felix Fietkau
89bd8607f8 hostapd: fix bringing up vlan interfaces with the no-bridge option
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-04 20:36:42 +02:00
Felix Fietkau
55ded1c265 netifd: update to the latest version
61a71e5e49c3 bridge: dynamically create vlans for hotplug members
cb6ee9608e10 bridge: fix dynamic delete of hotplug vlans
7f199050f395 wireless: pass the real network ifname to the setup script
50381d0a2998 bridge: allow adding/removing VLANs to configured member ports via hotplug

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-04 20:36:42 +02:00
Hans Dedecker
4fd4e9997a odhcpd: update to git HEAD
a12fcb3 config: log config parse failures to syslog
ebd4297 cmake: enforce additonal compiler checks
405da32 odhcpd: fix extra compiler warning

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2021-06-03 21:07:42 +02:00
John Crispin
96e9c81aab hostapd: fix radius problem due to invalid attributes
The offending commit caused the configuration file to contain:
  radius_auth_req_attr=
  radius_acct_req_attr=
which cause hostapd to add an ATTR of type 0 into the messages.

hostapd: RADIUS message: code=4 (Accounting-Request) identifier=0 length=93
hostapd:    Attribute 40 (Acct-Status-Type) length=6
hostapd:       Value: 7
hostapd:    Attribute 30 (Called-Station-Id) length=28
hostapd:       Value: 'C4-41-1E-F5-2D-55:OpenWifi'
hostapd:    Attribute 61 (NAS-Port-Type) length=6
hostapd:       Value: 19
hostapd:    Attribute 0 (?Unknown?) length=3    <----------------
hostapd:    Attribute 55 (Event-Timestamp) length=6
hostapd:       Value: 1622726457
hostapd:    Attribute 41 (Acct-Delay-Time) length=6
hostapd:       Value: 0
hostapd:    Attribute 44 (Acct-Session-Id) length=18
hostapd:       Value: '9B5961E7235AAEC6'

Fixes: 3bd6c8c728 (hostapd: add additional radius options)
Signed-off-by: John Crispin <john@phrozen.org>
2021-06-03 16:00:51 +02:00
Petr Štetiar
4f2243d40a ubus: update to version 2021-06-03
This update contains following changes:

 * ubusd: protect against too-short messages
 * ubusd: add per-client tx queue limit
 * ubusd: convert tx_queue to linked list

Fixes: FS#1525
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-06-03 10:16:49 +02:00
Felix Fietkau
2cd1a10829 mac80211: fix typo
Remove stray parenthesis

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-03 05:38:59 +02:00
Felix Fietkau
b474142fa8 mt76: update to the latest version
bddc1db76d0f mt76: mt7915: drop the use of repeater entries for station interfaces
3c90f35dddac mt76: mt7915: add thermal sensor device support
afab0e8202ff mt76: mt7915: add thermal cooling device support
41cf02184699 mt76: mt7615: add thermal sensor device support
2ac6b8762565 mt76: connac: update BA win size in Rx direction
ddb301127291 mt76: mt7921: fix reset under the deep sleep is enabled
e4cbefd1d69a mt76: mt7921: avoid unnecessary consecutive WiFi resets
393eea2034d7 mt76: mt7921: fix invalid register access in wake_work
a15d46407ffa mt76: mt7921: fix OMAC idx usage
e4d267d8e900 mt76: mt7921: enable runtime pm by default
50fd8ce2412a mt76: connac: add bss color support for sta mode
e29058c3c860 mt76: mt7921: return proper error value in mt7921_mac_init
c89c8c347b1e mt76: mt7921: do not schedule hw reset if the device is not running
9f7bb428e587 mt76: mt7921: reset wfsys during hw probe
22ea365913b5 mt76: mt7915: add .offset_tsf callback
ad91f8e8e494 mt76: mt7615: add .offset_tsf callback
6f871f35e3c1 mt76: mt7915: use mt7915_mcu_get_txpower_sku() to get per-rate txpower
597b68b7daa3 mt76: mt7615: remove useless if condition in mt7615_add_interface()
3945264468eb mt76: testmode: fix memory leak in mt76_testmode_alloc_skb
bdcc57a11606 mt76: testmode: remove unnecessary function calls in mt76_testmode_free_skb
a9763452601d mt76: testmode: remove undefined behaviour in mt76_testmode_alloc_skb
4aef2a2be464 mt76: mt7615: fix potential overflow on large shift
d9dd7635b055 mt76: mt7915: use mt7915_mcu_get_mib_info() to get survey data
d740e921758a mt76: mt7921: introduce mac tx done handling
259ddfc7cb73 mt76: mt7921: update statistic in active mode only
757b93f4b179 mt76: mt7921: remove leftover 80+80 HE capability
1fcff599b2e1 mt76: allow hw driver code to overwrite wiphy interface_modes
c55c22e39b7d mt7915: update firmware to 2020110522
10548aef1f45 mt76: mt7915: improve error recovery reliability
ed6b0c79820c mt76: mt7921: set MT76_RESET during mac reset
321443258bea mt76: move mt76_rates in mt76 module
d1652e8af9e1 Revert "mt76: connac: do not schedule wake_work if the runtime-pm is disabled"
4f4cab39ed9f mt76: mt7915: read all eeprom fields from fw in efuse mode
71450535f164 mt76: mt7921: enable hw offloading for wep keys
833d577e430c mt76: mt7921: remove mt7921_get_wtbl_info routine
67b7a22d2b99 mt76: mt7921: enable random mac address during sched_scan
cf1ff7bf4f1b mt76: mt7915: setup drr group for peers
ef2f7aa8745f mt76: mt7615: update radar parameters
b9f09f530223 mt76: mt7915: fix MT_EE_CAL_GROUP_SIZE

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-02 09:33:12 +02:00
John Crispin
98621c9782 hostapd: add eap_server support
This makes it possible to avoid using a RADIUS server for WPA enterprise authentication

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-02 09:33:12 +02:00
Felix Fietkau
704ab6a002 hostapd: add default values for r0kh/r1kh
This allows WPA enterprise roaming in the same mobility domain without any
manual key configuration (aside from radius credentials)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-02 09:33:12 +02:00
Felix Fietkau
ec223cf724 hostapd: add support for specifying the maxassoc parameter as a device option
It allows enforcing a limit on associated stations to be enforced for the
full device, e.g. in order to deal with hardware/driver limitations

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-02 09:33:12 +02:00
Felix Fietkau
e309b57619 hostapd: add support for configuring proxy ARP
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-02 09:33:12 +02:00
Felix Fietkau
190d4b6184 hostapd: add configurable rssi thresholds for rejecting assoc/probe requests
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-02 09:33:12 +02:00
Felix Fietkau
46509a51dd hostapd: add support for configuring the beacon rate
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-02 09:33:12 +02:00
Felix Fietkau
42a99b18ff mac80211: do not enable VHT in the default config on 2.4 GHz
Some drivers advertise it, but it's not supported at the moment

Reported-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-02 07:46:21 +02:00
Felix Fietkau
3518b793a2 mac80211: fix detecting VHT capabilities when generating the default config
The colon does not directly follow the "VHT Capabilities" string

Reported-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-06-02 07:46:21 +02:00
Adrian Schmutzler
54cc1756e2 hostapd: update to version 2021-05-22
This update only adds one commit:
b102f19bcc53 tests: Opportunistic Wireless Encryption - SA Query

The main reason for the bump is to have a newer PKG_SOURCE_DATE,
so we can reset PKG_RELEASE to 1 (this has not been done for the
most recent bump), and replace it with AUTORELEASE.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-05-29 00:31:25 +02:00
Rafał Miłecki
e002179a6d base-files: simplify setting device MAC
1. Move code above interface generation
   It results in more logical order. Device gets its config section
   above interface section.
2. Drop the loop
   We have separated code handling bridges now so $device should be
   guaranteed to contain a single device name.
3. Drop section name
   It's not required by netifd or LuCI & it's not needed by this script
   as $device contains a single device name now.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-28 15:35:32 +02:00
Jo-Philipp Wich
ec83fb9ced ubox: fix init script validation of log_ip option
The underlying logread process uses usock() to handle remote connections
which is able to handle both hostnames and IP addresses.

Ref: https://github.com/openwrt/luci/issues/5077
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2021-05-28 15:23:14 +02:00
Felix Fietkau
962d530dea hostapd: support verbose build using V=sc
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-27 12:17:02 +02:00
Rafał Miłecki
4b9a67362d base-files: generate network config with "device" options
Replace "ifname" with "device" as netifd has been recently patches to
used the later one. It's more clear and accurate.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-27 10:58:49 +02:00
David Bauer
553cc47ec7 hostapd: ACS: fix channel 100 frequency
Channel 100 is a valid channel to choose for 80MHz operation. However,
it's assigned to 5500 MHz, not 5550MHz. In fact, there is no channel
assigned to this frequency.

Fix this obbvious typo to allow ACS to select channel 100 for 80 MHz
operation again.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-26 23:12:09 +02:00
Evgeny Kolesnikov
3e9318f3c0 kernel: fix AutoLoad parameter for uleds module
The name of the module is 'uleds', not 'leds-uleds'.

Signed-off-by: Evgeny Kolesnikov <evgenyz@gmail.com>
[improve commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-26 23:10:54 +02:00
Chukun Pan
57cb387cfe ramips: add support for JCG Q20
JCG Q20 is an AX 1800M router.

Hardware specs:
  SoC: MediaTek MT7621AT
  Flash: Winbond W29N01HV 128 MiB
  RAM: Winbond W632GU6NB-11 256 MiB
  WiFi: MT7915 2.4/5 GHz 2T2R
  Ethernet: 10/100/1000 Mbps x3
  LED: Status (red / blue)
  Button: Reset, WPS
  Power: DC 12V,1A

Flash instructions:
  Upload factory.bin in stock firmware's upgrade page,
  do not preserve settings.

MAC addresses map:
  0x00004 *:3e wlan2g/wlan5g
  0x3fff4 *:3c lan/label
  0x3fffa *:3c wan

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2021-05-26 23:10:45 +02:00
Felix Fietkau
91abeebd3b mac80211: sync nl80211.h with upstream and backport a WPA3 related commit
Fixes compatibility issues with the latest hostapd update

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 20:08:25 +02:00
Felix Fietkau
fbd6f099f5 mac80211: add more HE capabilities
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:15 +02:00
Felix Fietkau
8d79915327 mac80211: fix center freq selection for 6 GHz
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Felix Fietkau
d87b58bb09 hostapd: fix adding back stations after a missed deauth/disassoc
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Felix Fietkau
eefed841b0 hostapd: update to version 2021-05-21
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Felix Fietkau
c8bcdd5619 mac80211: set hostapd op_class for 6 GHz
This is needed to disambiguate it from 5 GHz channels

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Felix Fietkau
8504212f65 mac80211: rework default config script
Emit the new band option instead of hwmode
Support 6 GHz band and HE options

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Felix Fietkau
8b8c1cb09b mac80211: make use of the new 'band' option
Use it to look up frequencies only in the configured band to better deal
with channel number overlap

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Felix Fietkau
db072fdc9e mac80211: add 6 GHz support to mac80211_hwsim
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Felix Fietkau
d76535c45e wireless-regdb: update to version 2021.04.21
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Andre Heider
b5420dd710 iw: update to 8fab0c9e
This fixes `iw dev wlan0-mesh station dump`.

8fab0c9 iw: fix ftm_request missing arguments segfault
e816fbc iw: fix mgmt dump missing arguments segfault
5d9d1b8 iw: Fix timestamp output on 32-bit architectures
4b25ae3 iw: fix pointer arithmetic in __print_he_capa
c3df363 iw: add option to print human readable event time
cd64525 iw: print ctrl port tx status event
0ba98b9 iw: use correct type in policy check for mesh
9e38dee iw: scan: fixup HE caps whitespace
17e8564 iw: scan: parse HE capabilities
5735e58 iw: util: factor out HE capability parser
6d8d507 iw: scan: add extension tag parsing
b4e1ec4 man: update wikipage URL, reformat SEE ALSO section
c56036a iw: enable 80MHz support for 6GHz band 11s mesh
fa72728 iw: handle positive error codes gracefully
7ba9093 iw: scan: add flag for scanning colocated ap
5ec60ed iw: Add 'coloc' and 'flush' options to sched_scan
f8ade75 iw: update wikipage URL
b6f2dac iw: Add support for specifying the 160MHz bandwidth when setting the channel/frequency

Signed-off-by: Andre Heider <a.heider@gmail.com>
2021-05-26 11:48:14 +02:00
Felix Fietkau
26da5c2359 hostapd: add support for configuring rts threshold
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Felix Fietkau
2319cf4ec0 hostapd: fix max_oper_chwidth setting for HE
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
John Crispin
3bd6c8c728 hostapd: add additional radius options
- add functionality to configure RADIUS NAS-Id and Operator-Name
- add functionality to configure RADIUS accounting interval
- enable RADIUS "Chargeable User Identity"

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Felix Fietkau
c76f1d8330 hostapd: add extra options for hotspot 2.0 / interworking
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Felix Fietkau
753a91d1d1 hostapd: report radar detected events via ubus
Events are reported on all BSS interfaces

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Felix Fietkau
8e2ca15726 hostapd: improve channel switch support
Instead of requiring the user to call it on each BSS individually,
run it on all BSSs internally.

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
Felix Fietkau
33c69aee41 hostapd: add missing inline stubs for ubus vlan event support
Only used when building without ubus support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-26 11:48:14 +02:00
John Crispin
937dd79e2a hostapd: fix civic location option
Signed-off-by: John Crispin <john@phrozen.org>
2021-05-26 11:48:14 +02:00
Rafał Miłecki
5fe549836f netifd: update to the latest master
899c2a4 interface: support "device" attribute and deprecate "ifname"
62e3cb5 scripts/netifd-wireless.sh: add support for specifying the operating band

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-26 07:56:27 +02:00
Nick Hainke
6687a2483a opkg: use $(PROJECT_GIT), $(AUTORELEASE) and SPDX
1) Use SPDX license headers to be machine readable.
2) Update copyright to 2021.
3) Use $(PROJECT_GIT) instead of manually specifying the git url.
4) Use $(AUTORELEASE) to automatically set the correct PKG_RELEASE.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-05-25 23:48:00 +02:00
Paul Spooren
efee640716 busybox: mention SRV support in help message
The SRV was added some time ago and should be mentioned in the short
help message to avoid confusion about missing features.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-05-24 20:30:04 +02:00
Hans Dedecker
7131f5a2fb nat46: fix memory leak
0d5860d fix memory leak in nat46_netdev_destroy().The netdev is forgotten to free in nat46_netdev_destroy function (#26)

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2021-05-24 13:02:41 +02:00
INAGAKI Hiroshi
8cc4e87a2f base-files: fix configuration generation of network if "bridge" exists
After the commit 43fc720657
("base-files: generate "device UCI type section for bridge"), the wrong
network configuration is generated for the devices that already have the
bridge device section for VLAN, such as the devices in realtek target.

As a result, the bridge device by additional "device" section is
specified to the "ports" option in the "bridge-vlan" section and netifd
shuts down the switch and the ethernet when the network service started.

Fixes: 43fc720657 ("base-files: generate "device" UCI type section for bridge")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rmilecki: use $ports for generate_bridge_vlan argument]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-24 09:09:00 +02:00
Rafał Miłecki
7a90ad3c43 base-files: support setting bridge MAC address
Fixes: 43fc720657 ("base-files: generate "device" UCI type section for bridge")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-24 07:48:17 +02:00
Hauke Mehrtens
1903233f2b treewide: Mark packages nonshared if they depend on @TARGET_
This marks all packages which depend on a target with @TARGET nonshared.
If they are not marked nonshared they would be build by the SDK build
and if this happens with a different SDK, then the SDK from the target
the package depends on, the package would not be added to the index.

This should fix the image builder for some of these packages.

This should fix the image builder at least for bcm27xx/bcm2710 and
bcm4908/generic.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-05-24 00:28:22 +02:00
Robert Marko
b054009854 mac80211: fix ATH_REG_DYNAMIC_USER_REG_HINTS
ATH_REG_DYNAMIC_USER_REG_HINTS is currently not being set as mac80211
tries to set it as m which is not possible as its boolean only.

Since its used alongside user regulatory, move it to USER_REGD.

This is required for ath11k to accept regulatory changes, otherwise
it wont accept any changes and will simply force US.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-23 15:11:38 +02:00
Alexander Egorenkov
42cd06f7fe kexec-tools: add patch to fix issue with appended DTB and zImage on ARM
This patch fixes a recently found problem when a zImage passed to
kexec-tools contains an appended DTB. In that case kexec boot fails because
the decompressor wrongly tries to use the non-existing appended DTB instaed
of the one passed in the register r2.

- http://lists.infradead.org/pipermail/kexec/2021-April/022353.html

Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
2021-05-23 15:11:38 +02:00
Konstantin Demin
0097899da7 binutils: update to 2.35.2
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
2021-05-23 15:11:38 +02:00
Aleksander Jan Bajkowski
08664f9bf3 kernel: limit crypto-hw-talitos to the mpc85xx and layerscape
CONFIG_CRYPTO_DEV_TALITOS depends on FSL_SOC. This driver only makes sense
on Freescale(NXP) SoCs.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-05-23 15:11:38 +02:00
Aleksander Jan Bajkowski
8f80b9b8f6 kernel: limit crypto-hw-geode to the x86/geode
CONFIG_CRYPTO_DEV_GEODE depends on X86_32. This driver only makes sense
on X86\geode.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-05-23 15:11:38 +02:00
Aleksander Jan Bajkowski
577ba5a3a9 kernel: crypto: drop kmod-crypto-pcompress
CONFIG_CRYPTO_PCOMP and CONFIG_CRYPTO_PCOMP2 have been removed in upstream commit[1].
This symbol doesn't exist since kernel 4.6 and this package is empty.

1. [ crypto: compress - remove unused pcomp interface ]
(110492183c)

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-05-23 15:11:38 +02:00
Aleksander Jan Bajkowski
f298d5b810 kernel: crypto: drop kmod-crypto-wq
CONFIG_CRYPTO_WORKQUEUE was removed in upstream commit[1]. This symbol doesn't
exist since kernel 5.3 and this package is empty.

1. [ crypto: cryptd - move kcrypto_wq into cryptd ]
(3e56e16863)

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-05-23 15:11:38 +02:00
Ivan Pavlov
b1baa01f14 wolfssl: add support for OpenVPN
Support for wolfSSL has been upstreamed to the master OpenVPN branch
in f6dca235ae560597a0763f0c98fcc9130b80ccf4, so we can use wolfSSL
directly in OpenVPN. So no more needed differnt SSL engine for OpenVPN
in systems based on wolfSSL library
Compiled && tested on ramips/mt7620, ramips/mt7621

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
2021-05-23 15:11:38 +02:00
Anderson McKinley
0eca9699b1 kernel: add kmod-input-leds
Adds support for LEDs on input devices. Useful for example on x86 laptops-
allows re-purposing num/caps/scroll lock LEDs.

Signed-off-by: Anderson McKinley <coyoso@tuta.io>
2021-05-23 15:10:30 +02:00
David Bauer
ddcb970274 hostapd: wolfssl: add RNG to EC key
Since upstream commit 6467de5a8840 ("Randomize z ordinates in
scalar mult when timing resistant") WolfSSL requires a RNG for
the EC key when built hardened which is the default.

Set the RNG for the EC key to fix connections for OWE clients.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-21 15:44:05 +02:00
David Bauer
ef9b103107 wolfssl: always export wc_ecc_set_rng
Since commit 6467de5a8840 ("Randomize z ordinates in scalar
mult when timing resistant") wolfssl requires a RNG for an EC
key when the hardened built option is selected.

wc_ecc_set_rng is only available when built hardened, so there
is no safe way to install the RNG to the key regardless whether
or not wolfssl is compiled hardened.

Always export wc_ecc_set_rng so tools such as hostapd can install
RNG regardless of the built settings for wolfssl.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-21 15:43:57 +02:00
Chen Minqiang
a9ebd3a0ea busybox: nslookup applet link with resolv if use glibc
This fixed b36b8b6929
("busybox: remove nslookup_lede/openwrt.patch")

It is likely dropped by mistake, This add back the changes

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2021-05-21 11:31:46 +02:00
Dirk Neukirchen
622f8ef577 grub2: disable liblzma dependency
Florian Ekert reported:

"I have build a fresh master branch recently, Since your last change [1]
on grub2, I have now a new dependency on liblzma for the install package
grub2-editenv.

root@st-dev-07 /usr/lib # ldd /root/grub-editenv
       /lib/ld-musl-x86_64.so.1 (0x7f684b088000)
       liblzma.so.5 => /usr/lib/liblzma.so.5 (0x7f684b06d000)
       libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x7f684b059000)
       libc.so => /lib/ld-musl-x86_64.so.1 (0x7f684b088000)

This was not the case before your update.

root@st-dev-07 /usr/sbin # ldd /usr/sbin/grub-editenv
       /lib/ld-musl-x86_64.so.1 (0x7fd970176000)
       libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x7fd970162000)
       libc.so => /lib/ld-musl-x86_64.so.1 (0x7fd970176000)

My build complains that it cannot satisfy the runtime package dependency
for grub2-editenv.

install -d -m0755 /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv/usr/sbin
install -m0755 /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/grub-editenv /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv/usr/sbin/
find /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv -name 'CVS' -o -name '.svn' -o -name '.#*' -o -name '*~'| xargs -r rm -rf
Package grub2-editenv is missing dependencies for the following libraries:
liblzma.so.5
make[2]: *** [Makefile:166: /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/bin/APOS/feckert/master/master-Maggie-455-ga5edc0e8e/x86_64/targets/x86/64/packages/grub2-editenv_2.06~rc1-1_x86_64.ipk] Error 1
make[2]: Leaving directory '/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/package/boot/grub2'
time: package/boot/grub2/pc/compile#78.64#9.79#83.88
   ERROR: package/boot/grub2 failed to build (build variant: pc).
make[1]: *** [package/Makefile:116: package/boot/grub2/compile] Error 1
make[1]: Leaving directory '/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt'
make: *** [/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/include/toplevel.mk:230: package/boot/grub2/compile] Error 2

If I add the following changes to the package all works as expected.

<snip>
-  DEPENDS:=@TARGET_x86
+  DEPENDS:=@TARGET_x86 +liblzma
  VARIANT:=pc
endef

This is a hotfix but I dont´t think this is the final solution, because lzma is provided by the package xz.
And This is maintained in the package feed [not the core]"

Dirk stated & offered his patch to disable liblzma and thus resolve the
'out of core dependency' problem:

"LZMA is used in mkimage.c
disabling it prints
Without liblzma (no support for XZ-compressed mips images) (explicitly disabled)
(see configure.ac)

liblzma is autodetected so this issue was present but hidden somehow

[unsure: grep/image generation does not use grub with that option]
OpenWrt does not use that feature currently

[!] some scripts and examples use --compression=xz or -C xz and those will break

grub has an internal xzlib for different "lzma" functionality
(ext. LIBLZMA from XZ (GRUB_COMPRESSION_XZ) vs. GRUB_COMPRESSION_LZMA)"

Hopefully fixes e74d81ece2 and doesn't
break anything else.

Signed-off-by: Dirk Neukirchen <plntyk.lede@plntyk.name>
[include Florian's description of how problem 1st encountered]
[bump package release]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-05-21 09:17:59 +01:00
Piotr Dymacz
6f3a05ebb0 uboot-envtools: support uci-default config also per subtargets
The current version of 'uboot-envtools' package generates dedicated
uci-default file only per target. This change makes it possible to
use subtarget-specific files, with name pattern: 'target_subtarget'
(example: 'ath79_nand'). The subtarget-specific files will take
precedence over target-specific one.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-05-20 13:57:43 +02:00
Piotr Dymacz
fab114f6f3 uboot-imx6: update BUILD_DEVICES values
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-05-20 13:45:12 +02:00
Piotr Dymacz
959eabf172 uboot-imx6: drop 'HIDDEN' flag from 'mx6cuboxi' define
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-05-20 13:45:12 +02:00
Rafał Miłecki
80be798d4a Revert "base-files: migrate old UCI network bridge ports syntax"
This reverts commit f716c30241.

Migrating everyone to the new syntax could break downgrades. We may
reintroduce it way later if needed.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-20 12:25:25 +02:00
Rafał Miłecki
cea6631cdf netifd: update to the latest master
config: fix ifname->ports compat rename

Fixes: 829b5c2ba3 ("netifd: update to the latest version")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-20 12:25:25 +02:00
Rafał Miłecki
0e459668c5 base-files: generate bridge device sections with br- name prefix
Missing br- prefix could result in name conflict between DSA port
interface and bridge interface. Some devices with just one LAN port use
"lan" interface name for DSA port. Trying to create bridge with the same
"lan" name was failing.

Reported-by: David Bauer <mail@david-bauer.net>
Fixes: 43fc720657 ("base-files: generate "device" UCI type section for bridge")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-20 10:40:59 +02:00
Philip Prindeville
b810d649fb busybox: preserve crontabs
/etc/syslog.conf is used by sysklogd, and /etc/crontabs is used
by crond, both features of busybox.  Given this, ownership for
these files should be bound to busybox, especially if one day
there's a way to do an in-place opkg update of busybox.

There's also the busybox provided syslogd which uses this file
if CONFIG_BUSYBOX_FEATURE_SYSLOGD_CFG is set.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
2021-05-19 15:50:50 +02:00
Nick Hainke
b36b8b6929 busybox: remove nslookup_lede/openwrt.patch
The nslookup_lede/openwrt applet was introduced in de5b8e5. It was
introduced because:

  Add a new LEDE nslookup applet which is compatible with musl libc
  and providing more features like ability to specify query type.

  In contrast to busybox' builtin nslookup applet, this variant does
  not rely on libc resolver internals but uses explicit send logic
  and the libresolv primitives to parse received DNS responses.

In busybox this applet is added in 0dd3be8. In particular, this commit
introduces the variable NSLOOKUP_BIG. We set the default to true and
so nothing changes.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-05-19 01:08:23 +02:00
Paul Spooren
a725382978 busybox: show reproducible timestamp
On login busybox shows a timestamp per default contianing the build
date. Since the build date isn't reproducible per default this behaviour
was disabled by default via 34df4d40 "busybox: disable timestamp in
version".

This commit modifies busybox so that the printed timestamp reproducible
using SOURCE_DATE_EPOCH and therefore shouldn't be disabled anymore.

Before:

    BusyBox v1.33.1 () built-in shell (ash)

After:

    BusyBox v1.33.1 (2021-05-13 09:34:34 UTC) built-in shell (ash)

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-05-19 00:32:46 +02:00
Rafał Miłecki
f716c30241 base-files: migrate old UCI network bridge ports syntax
netifd has been recently patched to use more accurate "ports" option
instead of "ifname". This is a simple translation between two UCI
options.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-18 20:07:56 +02:00
Rafał Miłecki
43fc720657 base-files: generate "device" UCI type section for bridge
This switches from the old way of defining bridges in an "interface" UCI
section type (that should be used for layer 3 only). From now a defualt
board switch will have its own "device" UCI section type. It's a new &
preferred way of defining L2 devices.

Before:

config interface 'lan'
        option type 'bridge'
        option ifname 'lan1 lan2 lan3 lan4'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'

After:

config device
        option name 'lan'
        option type 'bridge'
        list ports 'lan1'
        list ports 'lan2'
        list ports 'lan3'
        list ports 'lan4'

config interface 'lan'
        option ifname 'lan'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-18 20:07:51 +02:00
David Bauer
e884389976 rpcd: fix PKG_MIRROR_HASH
Fixes commit 97e820c6d6 ("rpcd: update to latest HEAD")

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-18 19:31:44 +02:00
Paul Spooren
25fdb42249 busybox: use $(AUTORELEASE) and SPDX
use AUTORELEASE since BusyBox is often updaten and PKG_RELEASE is not
consistently bumped. Also use SPDX license headers to be machine
readable and bump the copyright year to 2021.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-05-18 19:20:23 +02:00
Felix Fietkau
829b5c2ba3 netifd: update to the latest version
02dd2f2df7cb fix unannotated fall-through warnings
3052f2f67686 extdev: remove unused function
2a97fd006c3b device: add support for configuring devices with external auth handler
87e469be0c08 wireless: fix memory corruption bug when using vlans/station entries in the config
7277764bf817 bridge: rename "ifname" attribute to "ports"

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-18 12:56:32 +02:00
Felix Fietkau
cf45caeff1 hostapd: add patch for disabling automatic bridging of vlan interfaces
netifd is responsible for handling that, except if the vlan bridge
was provided by the config

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-18 12:52:52 +02:00
Felix Fietkau
2d89d7c748 hostapd: add ubus notifications for adding/removing vlan interfaces
This can be used to handle network configuration of dynamically created vlan
interfaces in a more flexible way

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-18 12:52:52 +02:00
Felix Fietkau
04d21604fd libubox: update to the latest version
870acee325fe tests: cram: test_base64: fix failing tests
4d8995e91d56 tests: cram: test_base64: really fix failing tests
551d75b5662c libubox: tests: add more blobmsg/json test cases
a0dbcf8b8f96 tests: add blob-buffer overflow test
b36a3a90098d blob: fix exceeding maximum buffer length
b8abed749423 utils.h: add fallthrough macro
b14c4688612c json_script: fix unannotated fall-through warning

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-18 12:52:52 +02:00
Rafał Miłecki
d42640e389 base-files: use "ports" array in board.json network for bridges
Bridge aggregates multiple ports so use a more accurate name ("ports")
and format (array) for storing them in board.json.

Example:

"network": {
	"lan": {
		"ports": [
			"lan1",
			"lan2",
			"lan3",
			"lan4"
		],
		"protocol": "static"
	},
	"wan": {
		"ifname": "wan",
		"protocol": "dhcp"
	}
}

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-18 12:30:16 +02:00
Hauke Mehrtens
097dc943f1 openwrt-keyring: Only copy sign key for snapshots
Instead of adding all public signature keys from the openwrt-keyring
repository only add the key which is used to sign the master feeds.

If one of the other keys would be compromised this would not affect
users of master snapshot builds.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-05-17 19:02:02 +02:00
Giulio Lorenzo
b108ed0ab0 ath79: add support for ZiKing CPE46B
ZiKing CPE46B is a POE outdoor 2.4ghz device with an integrated directional
antenna. It is low cost and mostly available via Aliexpress, references can
be found at:
- https://forum.openwrt.org/t/anddear-ziking-cpe46b-ar9331-ap121/60383
- https://git.lsd.cat/g/openwrt-cpe46b

Specifications:

- Atheros AR9330
- 32MB of RAM
- 8MB of flash (SPI NOR)
- 1 * 2.4ghz integrated antenna
- 2 * 10/100/1000 ethernet ports (1 POE)
- 3 * Green LEDs controlled by the SoC
- 3 * Green LEDs controlled via GPIO
- 1 * Reset Button controlled via GPIO
- 1 * 4 pin serial header on the PCB
- Outdoor packaging

Flashing instruction:

You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE. In case of issues with the vendor GUI, the vendor
Telnet console is vulnerable to command injection and can be used to gain
a shell directly on the OEM OpenWrt distribution.

Signed-off-by: Giulio Lorenzo <salveenee@mortemale.org>
[fix whitespaces, drop redundant uart status and serial0, drop
num-chipselects, drop 0x1002 MAC address for wmac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-05-17 01:01:32 +02:00
Florian Eckert
e0c6506158 base-files: change logging for upgrade on fwtool
Remove vn call in favour of v call. This commit serves as preparation
for removing the v function call.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
[alter slightly to prevent double space after colon]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-05-17 01:00:14 +02:00
Daniel Golle
23f98b3eb7
fstools: add missing #define _GNU_SOURCE
asprintf requires _GNU_SOURCE to be defined. Set it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-05-16 09:55:55 +01:00
Stijn Tintel
e74d81ece2 grub2: bump to 2.06-rc1
When building GRUB with binutils 2.35.2 or later, an error occurs due to
a section .note.gnu.property that is placed at an offset such that
objcopy needs to pad the img file with zeros. This in turn causes the
following error: "error: Decompressor is too big.".

The fix accepted by upstream patches a python script that isn't executed
at all when building GRUB with OpenWrt buildroot. There's another patch
that patches the files generated by that python script directly, but by
including it we would deviate further from upstream. Instead of doing
that, simply bump to the latest release candidate.

As one of the fixes for the CVEs causes grub to crash on some x86
hardware using legacy BIOS when compiled with -O2, filter -O2 and
-O3 out of TARGET_CFLAGS.

Fixes the following CVEs:
- CVE-2020-14372
- CVE-2020-25632
- CVE-2020-25647
- CVE-2020-27749
- CVE-2020-27779
- CVE-2021-3418
- CVE-2021-20225
- CVE-2021-20233

Runtime-tested on x86/64.

Fixes: FS#3790

Suggested-by: Dirk Neukirchen <plntyk.lede@plntyk.name>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-05-16 04:00:29 +03:00
Stijn Tintel
844598dcbb umdns: bump to git HEAD
777a0b service: fix compilation with GCC 10

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-05-16 03:59:54 +03:00
Daniel Golle
f8c98ee6c2
fstools: update to git HEAD
c44b40b overlay: fix syncronizing typo
 b5397a1 fstools: block: fix segfault on mount with no target
 bd7cc8d block: use dynamically allocated target string
 6d8450e blockd: use allocated strings instead of fixed buffers
 d47909e libblkid-tiny: fix buffer overflow
 67d2297 block: match device path instead of assuming /dev/%s
 2aeba88 block: allow autofs and umount commands also on MTD/UBI

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-05-16 00:37:01 +01:00
Felix Fietkau
f62aa9e781 mt76: update to the latest version
28b162366d09 mt76: fix calling mt76_get_of_eeprom with an offset for pre-cal data
9d736545bb5a mt76: mt7915: disable pre-calibration support for now

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-15 09:18:28 +02:00
Baptiste Jonglez
1ec6fc4dcb uclient: update to Git version 2021-05-14
6a6011d uclient-http: set eof mark when content-length is 0
19571e4 tests: fix help usage test for uclient built with sanitizer
c5fc04b tests: fix help usage test

Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2021-05-14 23:40:42 +02:00
Baptiste Jonglez
7fea9d9f5d busybox: disable PREFER_IPV4_ADDRESS
PREFER_IPV4_ADDRESS is broken on IPv6-only hosts, as it causes busybox
utilities (ping, traceroute, ntpd) to forcibly use the A record instead of
the AAAA record when resolving a DNS name.  This obviously fails when
there is no IPv4 connectivity.  Since IPv6-only hosts or routers will only
become more common over time, disable PREFER_IPV4_ADDRESS to support this
use-case.

As a side-effect, disabling PREFER_IPV4_ADDRESS changes the default
resolution behaviour of busybox utilities on dual-stack hosts.  Busybox
utilities now simply use the order given by getaddrinfo(), so they will
now prefer IPv6 addresses when resolving a name with both A and AAAA
records if there is IPv6 connectivity.  This is in line with RFC 6724.

PREFER_IPV4_ADDRESS was likely intended to work around naive
implementations of getaddrinfo() that could return AAAA records first,
even on an IPv4-only host.  But both musl (since 1.1.3) and glibc
correctly implement RFC 6724 for getaddrinfo() and check connectivity to
determine the correct order in which to return records.  On IPv4-only
hosts, getaddrinfo() will return A records first, so there is no need for
the PREFER_IPV4_ADDRESS hack.

See also: https://bugs.busybox.net/show_bug.cgi?id=12381

Fixes: FS#84
Fixes: FS#2608
References: https://github.com/openwrt/openwrt/pull/4167
Signed-off-by: Alexander Traud <pabstraud@compuserve.com>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2021-05-14 15:56:20 +02:00
Leonardo Mörlein
b993b68b6c build: introduce $(MKHASH)
Before this commit, it was assumed that mkhash is in the PATH. While
this was fine for the normal build workflow, this led to some issues if

    make TOPDIR="$(pwd)" -C "$pkgdir" compile

was called manually. In most of the cases, I just saw warnings like this:

    make: Entering directory '/home/.../package/gluon-status-page'
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    [...]

While these were only warnings and the package still compiled sucessfully,
I also observed that some package even fail to build because of this.

After applying this commit, the variable $(MKHASH) is introduced. This
variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the
correct path.

Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
2021-05-13 15:13:15 +02:00
Felix Fietkau
b5fb6761a2 mt76: update to the latest version
Includes fix for CVE-2020-24588

c7dd54a22e30 mt76: connac: skip wtbl reset on sta disconnect
3511fd430356 mt76: validate rx A-MSDU subframes
aedc3145de6e mt76: fix possible NULL pointer dereference in mt76_tx
5c2baab92cd0 mt76: mt7615: fix NULL pointer dereference in tx_prepare_skb()
af21659ee834 mt76: mt76x0: use dev_debug instead of dev_err for hw_rf_ctrl
e423c16f16f7 mt76: mt7615: free irq if mt7615_mmio_probe fails
f2d0da8da9b7 mt76: mt7663: enable hw rx header translation
d2713a5d9de9 mt76: mt7921: fix mt7921_wfsys_reset sequence
ce5f32d84f33 mt76: mt7921: Don't alter Rx path classifier
8ab8c7747197 mt76: connac: fw_own rely on all packet memory all being free
a747b0bb4956 mt76: mt7921: enable deep sleep at runtime
2e6e999509b1 mt76: mt7921: add deep sleep control to runtime-pm knob
30bcb2338ce2 mt76: connac: fix WoW with disconnetion and bitmap pattern
56518f4a126e mt76: mt7921: consider the invalid value for to_rssi
e969ab10a034 mt76: mt7921: add back connection monitor support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-13 10:25:18 +02:00
Nick Hainke
6713fe030f busybox: update to 1.33.1
Remove backports:
- 001-backport1330fix-ash-make-strdup-copy.patch
- 002-backport1330fix-traceroute.patch
- 005-backport-CVE-2021-28831.patch

Remove upstreamed:
- 010-fix-wrong-variable.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
[don't use $(AUTORELEASE) for now]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-05-12 18:32:03 +02:00
Felix Fietkau
025bd93f36 mac80211: backport upstream fixes for FragAttacks
From the patch series description:

Several security issues in the 802.11 implementations were found by
Mathy Vanhoef (New York University Abu Dhabi), who has published all
the details at

	https://papers.mathyvanhoef.com/usenix2021.pdf

Specifically, the following CVEs were assigned:

 * CVE-2020-24586 - Fragmentation cache not cleared on reconnection
 * CVE-2020-24587 - Reassembling fragments encrypted under different
                    keys
 * CVE-2020-24588 - Accepting non-SPP A-MSDU frames, which leads to
                    payload being parsed as an L2 frame under an
                    A-MSDU bit toggling attack
 * CVE-2020-26139 - Forwarding EAPOL from unauthenticated sender
 * CVE-2020-26140 - Accepting plaintext data frames in protected
                    networks
 * CVE-2020-26141 - Not verifying TKIP MIC of fragmented frames
 * CVE-2020-26142 - Processing fragmented frames as full frames
 * CVE-2020-26143 - Accepting fragmented plaintext frames in
                    protected networks
 * CVE-2020-26144 - Always accepting unencrypted A-MSDU frames that
                    start with RFC1042 header with EAPOL ethertype
 * CVE-2020-26145 - Accepting plaintext broadcast fragments as full
                    frames
 * CVE-2020-26146 - Reassembling encrypted fragments with non-consecutive
                    packet numbers
 * CVE-2020-26147 - Reassembling mixed encrypted/plaintext fragments

In general, the scope of these attacks is that they may allow an
attacker to
 * inject L2 frames that they can more or less control (depending on the
   vulnerability and attack method) into an otherwise protected network;
 * exfiltrate (some) network data under certain conditions, this is
   specific to the fragmentation issues.

A subset of these issues is known to apply to the Linux IEEE 802.11
implementation (mac80211). Where it is affected, the attached patches
fix the issues, even if not all of them reference the exact CVE IDs.

In addition, driver and/or firmware updates may be necessary, as well
as potentially more fixes to mac80211, depending on how drivers are
using it.

Specifically, for Intel devices, firmware needs to be updated to the
most recently released versions (which was done without any reference
to the security issues) to address some of the vulnerabilities.

To have a single set of patches, I'm also including patches for the
ath10k and ath11k drivers here.

We currently don't have information about how other drivers are, if
at all, affected.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-12 17:51:59 +02:00
Perry Melange
3a359398f0 busybox: add SRV support to nslookup_lede.c patch
Add support for querying and parsing SRV DNS records to nslookup_lede.c

This patch is based on http://lists.busybox.net/pipermail/busybox/2019-June/087359.html

Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
[reword subject, bump PKG_RELEASE]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-05-12 13:19:47 +02:00
Jo-Philipp Wich
75ea878d1b base-files: shinit: properly handle dashes in service names
Fixes: FS#3801
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2021-05-12 12:44:32 +02:00
Alexander Egorenkov
1854aeec4d build: fix opkg install step for large package selection
When the list of packages to be installed in a built image exceeds a certain
number, then 'opkg install' executed for target '$(curdir)/install' in
package/Makefile fails with: /usr/bin/env: Argument list too long.

On Linux, the length of a command-line parameter is limited by
MAX_ARG_STRLEN to max 128 kB.

* https://elixir.bootlin.com/linux/latest/source/include/uapi/linux/binfmts.h#L15
* https://www.in-ulm.de/~mascheck/various/argmax/

To solve the problem, store the package list being passed to 'opkg install'
in a temporary file and use the shell command substitution to pass the
content of the file to 'opkg install'. This guarantees that the length of
the command-line parameters passed to the bash shell is short.

The following bash script demonstrates the problem:
----------------------------------------------------------------------------
count=${1:-1000}

FILES=""
a_file="/home/egorenar/Repositories/openwrt-rel/bin/targets/alpine/generic/packages/base-files_1414-r16464+19-e887049fbb_arm_cortex-a15_neon-vfpv4.ipk"

for i in $(seq 1 $count); do
	FILES="$FILES $a_file"
done

env bash -c "echo $FILES >/dev/null"
echo "$FILES" | wc -c
----------------------------------------------------------------------------

Test run:
----------------------------------------------------------------------------
$ ./test.sh 916
130989
$ ./test.sh 917
./test.sh: line 14: /bin/env: Argument list too long
131132
----------------------------------------------------------------------------

Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
[reword commit subject]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-05-12 11:13:53 +02:00
Keith T. Garner
6a37286c2a kernel: add kmod-leds-uleds
The allows userspace LEDs to be created and controlled. This can be useful
for testing triggers and can also be used to implement virtual LEDs.

Signed-off-by: Keith T. Garner <kgarner@kgarner.com>
[squash fixup commit and improve option wording]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-05-12 10:47:23 +02:00
Felix Fietkau
06f5e8009d mt76: update to the latest version
186af01047b2 mt76: mt7921: introduce MCU_EVENT_LP_INFO event parsing
93b5c28c97d5 mt76: mt7921: add rcu section in mt7921_mcu_tx_rate_report
a8e89c5a1d1f mt76: testmode: add support to send larger packet
a0cc9a9e3877 mt76: mt7915: rework mt7915_tm_set_tx_len()
c8b96630324e mt76: mt7915: fix rate setting of tx descriptor in testmode
22fd2958c42a mt76: mt7615: fix memleak when mt7615_unregister_device()
7401e0db3143 mt76: mt7915: fix memleak when mt7915_unregister_device()
c3656268b3f6 mt76: mt7915: only free skbs after mt7915_dma_reset() when reset happens
0ce955b04ba8 mt76: mt7615: only free skbs after mt7615_dma_reset() when reset happens
b03d1e62acf7 mt76: mt7615: use ieee80211_free_txskb() in mt7615_tx_token_put()
5ac02e22fb03 mt76: flush tx status queue on DMA reset
c71f609b398a mt76: sync with upstream changes
23ecadd4af77 mt76: mt7615: fix hardware error recovery for mt7663
57a899ee3c3c mt76: mt7615: fix entering driver-own state on mt7663
42a2dddb706b mt76: mt7615: load ROM patch before checking patch semaphore status
cf0e406af84a mt76: mt7915: add support for applying pre-calibration data
459940ccbc58 mt76: mt7921: move hw configuration in mt7921_register_device
0a094b11f3c0 mt76: improve mcu error logging
bf536832e37d mt76: mt7921: run mt7921_mcu_fw_log_2_host holding mt76 mutex
7616f4f78163 mt76: mt7921: add wifisys reset support in debugfs
e620bd881ef5 mt76: mt7921: abort uncompleted scan by wifi reset
e8dacf59ab1c mt76: mt7915: rework the flow of txpower setting
c8c78e577236 mt76: mt7915: directly read per-rate tx power from registers
1622bf4f8705 mt76: mt7921: add mt7921_dma_cleanup in mt7921_unregister_device
ef96fafad8a9 mt76: Convert to DEFINE_SHOW_ATTRIBUTE
90e4bfea2948 mt76: mt7921: do not use 0 as NULL pointer
0a139d7f5966 mt76: connac: move mcu_update_arp_filter in mt76_connac module
de26c73ce3c2 mt76: mt7921: remove leftover function declaration
1c0b6cb4f942 mt76: mt7921: fix a race between mt7921_mcu_drv_pmctrl and mt7921_mcu_fw_pmctrl
2923e3e2b8e4 mt76: mt7663: fix a race between mt7615_mcu_drv_pmctrl and mt7615_mcu_fw_pmctrl
74d0fdaa7a99 mt76: connac: introduce wake counter for fw_pmctrl synchronization
28c87e09a5ea mt76: mt7921: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx path
36f664edc7db mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx path
51b3d1a9a2b7 mt76: dma: add the capability to define a custom rx napi poll routine
4f1339c9fb72 mt76: mt7921: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi
1bc5e67a60be mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi
325f7b451c03 mt76: connac: unschedule ps_work in mt76_connac_pm_wake
12115052a02f mt76: connac: check wake refcount in mcu_fw_pmctrl
e5d28e3cef66 mt76: connac: remove MT76_STATE_PM in mac_tx_free
475112a3cdcc mt76: mt7921: get rid of useless MT76_STATE_PM in mt7921_mac_work
112998f32d85 mt76: connac: alaways wake the device before scanning
4334f3e2fc43 mt76: mt7615: rely on pm refcounting in mt7615_led_set_config
0562380659ad mt76: connac: do not run mt76_txq_schedule_all directly
acfa78df5708 mt76: connac: use waitqueue for runtime-pm
ca74a4cd0722 mt76: remove MT76_STATE_PM in tx path
0c2d3e74852e mt76: mt7921: add awake and doze time accounting
45e0eefffe9f mt76: mt7921: enable sw interrupts
fd2ff641166f mt76: mt7615: Fix a dereference of pointer sta before it is null checked
7e2521468767 mt76: mt7921: move mt7921_dma_reset in dma.c
c9dd6b1fa171 mt76: mt7921: introduce mt7921_wpdma_reset utility routine
2ac7c7e9c568 mt76: mt7921: introduce mt7921_dma_{enable,disable} utilities
662a89f2b9d1 mt76: mt7921: introduce mt7921_wpdma_reinit_cond utility routine
614efe9e9180 mt76: connac: introduce mt76_connac_mcu_set_deep_sleep utility
0dbb16ef39d8 mt76: mt7921: enable deep sleep when the device suspends
3c19f569cc70 mt76: mt7921: fix possible invalid register access
ade1f5aad4c6 mt76: move token_lock, token and token_count in mt76_dev
8d5c456be1ff mt76: move token utilities in mt76 common module
fb04d9df5e52 mt76: mt7915: do not read rf value from efuse in flash mode
2126b2176336 mt76: mt7921: get rid of mcu_reset function pointer
d325b7eff1b1 mt76: mt7921: improve doze opportunity
2ae25c7e547e mt76: mt7663: add awake and doze time accounting
349bbb9d6f13 mt76: connac: unschedule mac_work before going to sleep
98a235004dea mt76: mt7921: mt7921_stop should put device in fw_own state
63d80b9ab251 mt76: mt7921: introduce mt7921_mcu_sta_add routine
3c5bf837fdbd mt76: mt7615: fix a precision vs width bug in printk
ded14da5eacc mt76: mt7915: fix a precision vs width bug in printk
aaf0d254f9ea mt76: mt7921: fix a precision vs width bug in printk
757af5c67d32 mt76: move mt76_token_init in mt76_alloc_device
ed41ed73a495 mt76: mt7921: reinit wpdma during drv_own if necessary
92fb81e085c6 mt76: mt7921: fix possible AOOB issue in mt7921_mcu_tx_rate_report
53d915a23bc9 mt76: connac: do not schedule wake_work if the runtime-pm is disabled
23fe1bdcf15a mt76: connac: do not schedule mac_work if the device is not running
e5b19336c58e mt76: mt7615: do not set MT76_STATE_PM at bootstrap
0fc2136a61dd mt76_connac_mcu: move mt76_connac_mcu_update_arp_filter outside of CONFIG_PM
e693f3e23e06 mt76: mt7915: add MSI support
5231e7300fa4 mt7915: disable ASPM
554b50dabf54 mt76: connac: fix uninitialized HT A-MPDU setting field in STA_REC_PHY
43b9c0a838bb mt76: mt7921: fix max aggregation subframes setting
5a387a0a3004 mt76: mt7921: enable rx hw de-amsdu
c8cbcb87be07 mt76: connac: add missing configuration in mt76_connac_mcu_wtbl_hdr_trans_tlv
55921e57b380 mt76: mt7921: enable rx header traslation offload
01441f67d8b2 mt76: mt7921: enable rx csum offload
c9ab76dd93a0 mt76: mt7915: move mt7915_queue_rx_skb to mac.c
caedb4c4ee41 mt76: mt7615: fix fixed-rate tx status reporting
c6ae95d43e6d mt76: improve tx status codepath
27d468d094e6 mt76: mt7915: rework tx rate reporting
3b4ca5b09e2c mt76: mt7615: avoid use of ieee80211_tx_info_clear_status
e1f07d7f1cb9 mt76: mt7603: avoid use of ieee80211_tx_info_clear_status
18513ba5fbc2 mt76: mt7915: add support for tx status reporting
35f189cf81b2 mt76: mt7915: fix uninitialized variable in MSI error handling
9e928ac1ea9b mt76: dma: use ieee80211_tx_status_ext to free packets when tx fails
628eee9c386c mt76: fill queue entry wcid for all skbs with a station
a9bc4d94b7a1 mt76: intialize tx queue entry wcid to 0xffff by default
998ca8af7d17 mt76: mt7915: fix tssi indication field of DBDC NICs
7dd24b3cfacf mt76: mt7915: fix a signedness bug in mt7915_mcu_apply_tx_dpd()
535025d65d8d mt76: mt7915: cleanup mt7915_mcu_sta_rate_ctrl_tlv()
ff8bbe22dd87 mt76: mt7915: add .set_bitrate_mask() callback

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-05-10 12:37:36 +02:00
Daniel Golle
21b8550598
rpcd: set correct PKG_SOURCE_DATE
The previous commit bumped the source commit level without reflecting
that in PKG_SOURCE_DATA. Bump PKG_SOURCE_DATA as well.

Fixes: 97e820c6d6 ("rpcd: update to latest HEAD")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-05-10 10:57:09 +01:00
David Bauer
97e820c6d6 rpcd: update to latest HEAD
7a560a1 iwinfo: add 802.11ax HE support

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-10 01:20:00 +02:00
Bjørn Mork
2449a63208 ramips: mt7621: Add support for ZyXEL NR7101
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.

Specifications:

 - SoC: MediaTek MT7621AT
 - RAM: 256 MB
 - Flash: 128 MB MB NAND (MX30LF1G18AC)
 - WiFi: MediaTek MT7603E
 - Switch: 1 LAN port (Gigabiti)
 - 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
 - SIM: 2 micro-SIM slots under transparent cover
 - Buttons: Reset, WLAN under same cover
 - LEDs: Multicolour green/red/yellow under same cover (visible)
 - Power: 802.3at PoE via LAN port

The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.

UART Serial:

57600N1
Located on populated 5 pin header J5:

 [o] GND
 [ ] key - no pin
 [o] RX
 [o] TX
 [o] 3.3V Vcc

Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable.  Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.

A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.

MAC addresses:

OpenWrt OEM   Address          Found as
lan     eth2  08:26:97:*:*:BC  Factory 0xe000 (hex), label
wlan0   ra0   08:26:97:*:*:BD  Factory 0x4 (hex)
wwan0   usb0  random

WARNING!!

ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled.  Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.

Installation from OEM web GUI:

- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
  Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot

Installation from OEM ssh:

- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
    nvram setro uboot DebugFlag 0x1
    nvram setro uboot CheckBypass 0
    nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot

Copying OpenWrt to the recovery partition:

- Verify that you are running a working OpenWrt recovery image
  from flash
- ssh to root@192.168.1.1 and run:
    fw_setenv CheckBypass 0
    mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2

NOTE: This should only be done after successfully booting the OpenWrt
  recovery image from the primary partition during installation.  Do
  not do this after having sysupgraded OpenWrt!  Reinstalling the
  recovery image on normal upgrades is not required or recommended.

Installation from Z-Loader:

- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
  image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image

NOTE: ATNR will write the recovery image to both primary and recovery
  partitions in one go.

Booting from RAM:

- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
  image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm  0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
  header

This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies!  Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.

NOTE: U-Boot configuration is incomplete (on some devices?). You may
  have to configure a working mac address before running tftp using
   "setenv eth0addr <mac>"

Unlocking the bootloader:

If you are unebale to halt boot, then the bootloader is locked.

The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0.  Setting it to 1 is therefore only temporary
when OEM firmware is installed.

- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt

  NOTE:
    OpenWrt does this automatically on first boot if necessary

  NOTE2:
    Setting the flag to 0x1 avoids the reset to 0 in known OEM
    versions, but this might change.

  WARNING:
    Writing anything to flash while the bootloader is locked is
    considered extremely risky. Errors might cause a permanent
    brick!

Enabling management access from LAN:

Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:

- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"

Notes on the OEM/bootloader dual partition scheme

The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.

Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.

The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.

If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.

If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.

If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally.  CheckBypass is set to 1 after each successful
validation of Image1.

Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger.  But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.

The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.

Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.

Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-05-09 09:15:44 +02:00
Daniel Golle
cc201759b6
uboot-mediaktek: add support for PSTORE and check it on boot
Add support for pstore/ramoops now that DRAM content is preserved
over reboot on MT7622. On each boot, check pstore and boot to recovery
image in case there are records stored in it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-05-08 23:35:38 +01:00
Daniel Golle
c91c0c1f85
arm-trusted-firmware-mediatek: update to git HEAD
Most notably this enabled use of pstore/ramoops on MT7622 as DRAM
content is now preserved over reboot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-05-08 23:27:38 +01:00
Thomas Richard
2eda042d55 uqmi: fix network registration loop
With some debug in qmi.sh using following patch, some errors are visible
in the registration step
@@ -29,6 +29,7 @@ proto_qmi_init_config() {
 }

 proto_qmi_setup() {
+       set -x
        local interface="$1"
        local dataformat connstat plmn_mode mcc mnc
        local device apn auth username password pincode delay modes pdptype
@@ -224,6 +225,8 @@ proto_qmi_setup() {
                fi
        done

+       registration=$(uqmi -s -d "$device" --get-serving-system)
+
        [ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes" > /dev/null 2>&1

        echo "Starting network $interface"

During the boot of the system, modem could not start automatically its
network registration.
netifd: wan (9235): + echo 'Waiting for network registration'
netifd: wan (9235): Waiting for network registration
netifd: wan (9235): + local 'registration_timeout=0'
netifd: wan (9235): + uqmi -s -d /dev/cdc-wdm1 --get-serving-system
netifd: wan (9235): + grep '"searching"'
netifd: wan (9235): + uqmi -s -d /dev/cdc-wdm1 --get-serving-system
netifd: wan (9235): + registration='{"registration":"not_registered","plmn_mcc":208,"plmn_mnc":20,"plmn_description":"","roaming":true}'
netifd: wan (9235): + '[' -n  ]
netifd: wan (9235): + echo 'Starting network wan'

As the while loop checks only "searching" pattern, uqmi.sh script quits
searching loop and continues whereas the modem is not registered

Other issue, after X seconds modem stops searching.
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + grep '"searching"'
netifd: wan (9213): + '[' -e /dev/cdc-wdm0 ]
netifd: wan (9213): + '[' 3 -lt 0 -o 0 '=' 0 ]
netifd: wan (9213): + let registration_timeout++
netifd: wan (9213): + sleep 1
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + grep '"searching"'
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + registration='{"registration":"not_registered"}'
netifd: wan (9213): + '[' -n  ]
netifd: wan (9213): + echo 'Starting network wan'
netifd: wan (9213): Starting network wan

If registration_timeout is not expired, registration can be restarted

Signed-off-by: Thomas Richard <thomas.richard@kontron.com>
Tested-by: Florian Eckert <fe@dev.tdt.de>
2021-05-08 12:29:24 +02:00
Daniel Golle
f990bddf6f
uboot-envtools: change size for unifi-6-lr
The previous commit increased the U-Boot environment size of the
UniFi 6 LR to 0x4000. Also change it uboot-envtools accordingly.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-05-07 22:50:22 +01:00
Daniel Golle
af3a1adee0
uboot-mediatek: unifi-6-lr: fix erase of production parition
mtd erase needs to be aligned with erase blocks. Use padded image size
for erasing the production volume.
As the environment grew above the current size of 0x1000 bytes by
introducing the new padding function, increase the env size to 0x4000.
While at it, clean up reset button function to work to more reliable on
that board.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-05-07 22:50:15 +01:00
Daniel Golle
b607e7df34
procd: update to git HEAD
021ece8 procd: Use /dev/console for serial console if exists

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-05-05 13:18:50 +01:00
Daniel Golle
a2b9ec0231
base-files: upgrade: take down loop and LVM before upgrade
Users of devices with large block storage may choose to have an LVM
partition on the same device which is used for booting OpenWrt.
The presents a problem during sysupgrade as the root device is then
still busy and changing partitions will not work as desired,
leading to data corruption in case the newly flashed image is larger
than the currently installed one.
Having loop devices setup causes similar havoc.
Make sure all volume groups are offline and all loop devices have been
released before sysupgrade.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-05-05 13:18:43 +01:00
Alan Swanson
3980daffa4 dnsmasq: Update to version 2.85
Fixes issue with merged DNS requests in 2.83/2.84 not being
retried on the firsts failed request causing lookup failures.

Also fixes the following security problem in dnsmasq:
* CVE-2021-3448:
  If specifiying the source address or interface to be used
  when contacting upstream name servers such as:
  server=8.8.8.8@1.2.3.4, server=8.8.8.8@1.2.3.4#66 and
  server=8.8.8.8@eth0 then all would use the same socket
  bound to the explicitly configured port. Now only
  server=8.8.8.8@1.2.3.4#66 will use the explicitly
  configured port and the others random source ports.

Remove upstreamed patches and update remaining patch.

Signed-off-by: Alan Swanson <reiver@improbability.net>
[refreshed old runtime support patch]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-05-05 09:19:46 +01:00
Hauke Mehrtens
454d514f46 ltq-dsl-base: Make package nonshared to fix image builder
This package depends on the lantiq target and is only build for that
target. A normal package would be build by the SDK builder probably
under a different target and then this package will not be selected.
Mark it as nonshared to build it when the lantiq target gets build.

Fixes: FS#3773, FS#3774
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-05-04 22:25:47 +02:00
Hauke Mehrtens
17ac9849d3 mac80211: Update to version 5.10.34-1
The removed patches were applied upstream and are not needed anymore.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-05-04 22:25:43 +02:00
Hauke Mehrtens
13397b2b95 busybox: backport fix for CVE-2021-28831
This backports a fix for the low priority CVE-2021-28831:
  decompress_gunzip.c in BusyBox through 1.32.1 mishandles the error bit
  on the huft_build result pointer, with a resultant invalid free or
  segmentation fault, via malformed gzip data.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-05-02 19:06:02 +02:00
David Bauer
5515c29029 iwinfo: update to latest Git HEAD
c45f0b5 iwinfo: add 802.11ax HE rate information

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-02 02:40:20 +02:00
Daniel Golle
fbcfa895a8
uboot-mediatek: bpi-r64: add TFTP update options to eMMC bootmenu
Just like on SPI-NAND, also allow updating the bootloader comfortably
on eMMC installations.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-05-01 22:55:22 +01:00
Chukun Pan
5e926c26d4 kernel: qlcnic: fix typo in module description
Fixes: f88c64d28c ("kernel: netdev: add qlcnic")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2021-05-01 21:48:57 +02:00
Hauke Mehrtens
95b210e513 kernel: qlcnic: add dependency to kmod-hwmon-core
QLCNIC_HWMON was activated when hwmon was set, but the dependency was
missing. This broke the build bot builds. Fix this by explicitly
activating HWMON support and adding a dependency.

Fixes: f88c64d28c ("kernel: netdev: add qlcnic")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-05-01 12:00:41 +02:00
Rui Salvaterra
eeda8652f1 mac80211/rtl: backport a rtl8192cu AP mode fix
Running USB devices in AP mode is never a good idea. That said, fix the TIM
issue in rtl8192cu [1], allowing these devices to "work" in AP mode.

[1] https://patchwork.kernel.org/project/linux-wireless/patch/20210419065956.6085-1-pkshih@realtek.com/

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-05-01 00:37:15 +02:00
Vieno Hakkerinen
f88c64d28c kernel: netdev: add qlcnic
Add driver for QLogic QLE8240 and QLE8242 Converged Ethernet devices.

Signed-off-by: Vieno Hakkerinen <vieno@hakkerinen.eu>
2021-05-01 00:37:09 +02:00
Chen Minqiang
e219b7f38b kernel: add kmod-ipvlan support
This kmod is similar to macvlan with the difference being that the
endpoints have the same mac address.

It is useful on cloud where only one mac address allowed on port,
where macvlan not works but ipvlan would.

One use case is where multiple IPs and gateways assign on one net port

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2021-04-30 23:51:23 +02:00
Mauri Sandberg
addf47a9a8 uboot-envtools: add support for Buffalo WZR-HP-G300NH
This adds an entries for wzr-hp-g300nh-rb and wzr-hp-g300nh-s.

Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
2021-04-30 23:51:23 +02:00
Roger Pueyo Centelles
d1f1e5269e ipq40xx: add support for MikroTik SXTsq 5 ac
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - RAM: 256 MB
 - Storage: 16 MB NOR
 - Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
 - Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
 - 1x Ethernet LED (green)
 - 7x user-controllable LEDs
  · 1x power (blue)
  · 1x user (green)
  · 5x rssi (green)

Note:
 Serial UART is probably available on the board, but it has not been
 tested.

Flashing:
 Boot via TFTP the initramfs image. Then, upload a sysupgrade image
 via SSH and flash it normally. More info at the "Common procedures
 for MikroTik products" page https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2021-04-29 10:55:07 +02:00
Chen Minqiang
43dad22025
uboot-mediatek: unifi6lr: mtd erase before write to flash
Erase firmware ereas before writing to recovery or production partition
when updating them via the bootloader menu.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-04-28 20:54:43 +01:00
Daniel Golle
ebed523ee8
arm-trusted-firmware-mediatek: fix boot hang on unifi-6-lr
The Ubiquiti Networks UniFi 6 LR access point comes with a total of
512 MB RAM provided by 2x 8-bit DDR3 SDRAM. This combination lead to
problems with the DDR calibration on boot resulting in occasional hang
on boot. Use updated calibration binary provided by MediaTek to make
boot on that device more reliable.
The binary has also been tested on the BananaPi BPi-R64 board and that
also works just fine with the new binary.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-04-28 20:51:53 +01:00
Felix Fietkau
12cb52bd06 mac80211: minstrel_ht: fix issue in calculating success probability
Missing braces in a macro were leading to badly working rates sometimes
getting a success probabilty of 1.0

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-28 21:08:29 +02:00
David Bauer
6f77ce7724 iwinfo: update to latest Git HEAD
50b64a6 iwinfo: add basic IEEE 802.11ax support
70d2136 iwinfo: nl80211: perform split wiphy dump
cd23727 iwinfo: cli: fix hwmode formatting

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-04-28 03:08:10 +02:00
João Henriques
e8a5670122 dnsmasq: add ignore hosts dir to dnsmasq init script
When running multiple instances of dnsmasq, for example one being for the lan
and another for a guest network, it might not be desirable to have the same dns names
configured in both networks

Signed-off-by: João Henriques <joaoh88@gmail.com>
2021-04-24 21:35:27 +02:00
Hans Dedecker
c61ab68387 nat46: update to git HEAD
9df230a Zero checksum handling  (#25)
7688102 skip generating a UDP4 csum if the UDP6 csum is 0 and zero_csum_pass is set
4a9e4b1 zero csum: avoid calling the checksum adjustment function if udp csum is zero
2de14c5 add a module argument to skip checksum adjust for UDP if checksum is zero

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2021-04-24 21:11:33 +02:00
Tony Ambardar
aabc632023 bpftools: update to v5.11.16, simplify make
Update to the latest stable upstream version.

Drop unneeded make variables to remove redundant assignments seen during
invocation of package Makefile.

Also remove the following patch now included upstream:

  * 200-fix-install-param-order-on-macos.patch

Compile and run-tested on malta/mips32be, using bpftool directly and also
libbpf (linked with tc) to inspect and load simple eBPF programs.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-04-24 12:21:40 +01:00
Tony Ambardar
cf20f1bb5f bpftools: fix feature override for masking clang
Rename feature variable clang-bpf-global-var following upstream changes.
This restores the HAVE_CLANG feature override and should avoid rare build
errors where a recent host clang and BTF-enabled host kernel are present.

Fixes: 23be333401 ("bpftools: update to 5.10.10")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-04-24 12:21:40 +01:00
Tony Ambardar
3e3af1908c iproute2: avoid unneeded compiles to speed building
Skip building Makefile targets that aren't packaged: tipc, dcb, ifstat,
rtacct, lnstat, and man. Also, only compile targets needed for the current
build variant i.e. don't compile 'tc' when building an 'ip' variant and
vice versa.

These changes reduce typical build times by over 30%:
  $ make package/iproute2/clean && time make -j8 package/iproute2/compile
  (old)
  ...
  real    2m24.985s
  user    3m12.537s
  sys     0m26.677s

  (new)
  ...
  real    1m36.945s
  user    2m8.734s
  sys     0m20.046s

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-04-22 15:11:36 +01:00
David Bauer
b832ebb886 uboot-rockchip: update to v2021.04
Update the uboot-rockchip to the latest upstream release.
Remove upstreamed patches.

Tested-on: FriendlyElec NanoPi R2S

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-04-20 13:15:45 +02:00
David Bauer
4978e073cd kernel: select kmod-backlight as dependency for kmod-drm
Select kmod-backlight as dependency for kmod-drm in case kmod-backlight
is compiled.

This fixes kernel 5.10 build issues on x86-geode with all kmods
enabled:

Package kmod-drm is missing dependencies for the following libraries:
backlight.ko

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-04-18 14:41:02 +02:00
David Bauer
7cea19c2ce kernel: netdev: make kmod-of-mdio conflict with x86
CONFIG_MDIO_OF depends on CONFIG_OF which is not enabled for x86.

Fixes builds of x86 with Kernel 5.10 due to unresolved dependencies.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-04-18 14:40:55 +02:00
Daniel González Cabanelas
4f8da19572 uboot-envtools: mvebu: add Buffalo LS421DE
The Buffalo Linkstation LS421DE NAS lacks an uboot env config file.

Create it via scripts.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2021-04-17 22:44:09 +01:00
DENG Qingfang
10aacb9a6c kernel/modules: move act_gact into kmod-sched-core
As the name suggests, act_gact has the generic actions such as dropping
and accepting packets, so move it into kmod-sched-core.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
2021-04-17 21:56:05 +02:00
Josef Schlehofer
b265649085 linux-firmware: ath10k: add support for Qualcomm Atheros QCA9377
Add firmware and board file for Qualcomm Atheros QCA9377 802.11ac Wireless
Network Adapter (rev 31) recognized as [168c:0042].

This card supports standard 1x1 802.11ac Wave2, BT5, and MU-MIMO.

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2021-04-17 21:56:05 +02:00
Florian Eckert
4407d45d96 ltq-vdsl-app: extent dsl metrics with state_num and power_state_num
With the old ubus dsl API, the numbers for the individual line_states and
power_states were also returned. These were not ported to the new DSL
C-API. This commit adds the missing information.

For this the internal values are mapped to numbers.

* additional JSON output for state_num:
"state_num": <map_state_number>

Since not all values are meaningful only the following values are
implemented, this can be extended if the future.

* LSTATE_MAP_NOT_INITIALIZED
* LSTATE_MAP_EXCEPTION
* LSTATE_MAP_IDLE
* LSTATE_MAP_SILENT
* LSTATE_MAP_HANDSHAKE
* LSTATE_MAP_FULL_INIT
* LSTATE_MAP_SHOWTIME_NO_SYNC
* LSTATE_MAP_SHOWTIME_TC_SYNC
* LSTATE_MAP_RESYNC

* additinal JSON output for power_level:
"power_state_num": <map_power_satte_number>,

Since there are not so many here, all are mapped.

* PSTATE_MAP_NA,
* PSTATE_MAP_L0,
* PSTATE_MAP_L1,
* PSTATE_MAP_L2,
* PSTATE_MAP_L3,

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
v6:
Add state LSTATE_MAP_NOT_INITILIZED at the beginning of the list
Start the list LSTATE_MAP with -1
Reviewed-by: Andre Heider <a.heider@gmail.com>
2021-04-17 21:56:05 +02:00
Leon M. George
f6cc00650c odhcp6c: read user scripts from directory
Placeholder DHCP user scripts were added recently.

These files make package-based installations of such scripts more difficult.
Pull user callbacks from directories instead to allow packages and users to
install co-existing scripts more easily.

References:
b4f3d93b5 odhcp6c: add a odhcp6c.user placeholder script

Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
2021-04-17 21:15:33 +02:00
Leon M. George
467c32600c netifd: read udhcpc user scripts from directory
Placeholder DHCP user scripts were added recently.

These files make package-based installations of such scripts more difficult.
Pull user callbacks from directories instead to allow packages and users to
install co-existing scripts more easily.

References:
130118f7a netifd: add a udhcpc.user placeholder script

Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
2021-04-17 21:13:37 +02:00
Rosen Penev
0ec8c793f5 libsemanage: fix pkgconfig paths
The pkgconfig file currently points to host paths.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-04-15 11:54:14 +01:00
Zoltan HERPAI
d6cf997bd7 uboot-sunxi: update ATF dependencies for 3 boards
Fix 3 board definitions that were missed in the process of moving
to the a64/h6 ATF blobs.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2021-04-15 00:24:50 +02:00
Rafał Miłecki
05a4273058 uci: update to the latest master
4b3db11 cli: add option for changing save path

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-04-14 08:33:12 +02:00