Since we split the Inteno XG6846 "firmware" partition with the
uImage MTD splitter, we need to compile in support for this
splitting method into the BCM6328.
Reviewed-by: Paul Donald <newtwen+github@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit [ca8c30208d5e][1] updates procd to handle muliple "console=" on the
kernel command line. This affects Raspberry Pi builds because cmdline.txt
specifies a UART console and a virtual console on HDMI, in that order.
When procd finds multiple consoles on the command line, it attempts to
open /dev/console. Linux uses the [last console][2] for /dev/console, so
procd opens the virtual console on Raspberry Pi. This completely disables
the UART console and causes [strange behavior][3] on the virtual console.
Prior to ca8c30208d5e, procd would always open the first console, which is
the UART console.
The simplest fix without reverting ca8c30208d5e is to swap the order of
console options in cmdline.txt. By putting the UART console last, procd
handles the serial console correctly as before.
[1]: https://git.openwrt.org/?p=project/procd.git;a=commit;h=ca8c30208d5e1aaa2c0e3f732c4c9944735e9850
[2]: https://www.kernel.org/doc/html/latest/admin-guide/serial-console.html
[3]: https://forum.openwrt.org/t/rasberry-pi-4-model-b-keyboards-gone-wild/195594
Signed-off-by: Elbert Mai <code@elbertmai.com>
Currently, the MT7530 DSA subdriver configures the MT7530 switch to provide
direct access to switch PHYs, meaning, the switch PHYs listen on the MDIO
bus the switch listens on. The PHY muxing feature makes use of this.
This is problematic as the PHY may be attached before the switch is
initialised, in which case, the PHY will fail to be attached.
Since commit 91374ba537bd ("net: dsa: mt7530: support OF-based registration
of switch MDIO bus") on mainline Linux, we can describe the switch PHYs on
the MDIO bus of the switch on the device tree.
When the PHY is described this way, the switch will be initialised first,
then the switch MDIO bus will be registered. Only after these steps, the
PHY will be attached.
Describe the switch PHYs on mt7621.dtsi and remove defining the switch PHY
on the SoC's mdio bus node. When the PHY muxing is in use, the interrupts
for the muxed PHY won't work, therefore delete the "interrupts" property on
the devices where the PHY muxing feature is in use.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
The ethernet-phy@4 node doesn't exist for WAVLINK WL-WN573HX1. Remove it
and the duplicate gmac0 node.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Currently, the pinctrl-0 property on the ethernet node is modified to
exclude the rgmii1 and rgmii2 pin groups to be claimed with rgmii1 and
rgmii2 functions, respectively. Remove the modification of this property as
we need these pin groups to be claimed with the said functions for this
device.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
1. Enable this feature only for 32-bit CPUs as MIPS64 can not
access the full range unmapped uncached memory.
2. Backport this fix to the 6.1 old LTS kernel.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
There was no config in the uboot-envtools package, so there is no
generated /etc/fw_env.config for the fw_printenv and fw_setenv utils.
Since uboot-envtools 2024.01, there is a way to make these utils work
without /etc/fw_env.config if the DT has an env partition with the prop.:
compatible = "u-boot,env";
So, this commit adds the prop. above to the appsblenv:0 partition
in the yuncore ax880 DTS file.
Signed-off-by: Isaev Ruslan <legale.legale@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15305
Signed-off-by: Robert Marko <robimarko@gmail.com>
Turn on SoC pull-ups on I2C pins, since there are no discrete pull-up
resistors on the bus.
Increase clock to 400 kHz. Both chips on the bus support 400 kHz. I
tested the ISL28022 at 4,000 reads/sec and didn't see any garbled output
or bus hangs, even with SoC drive strength reduced to 2 for the test.
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15334
Signed-off-by: Robert Marko <robimarko@gmail.com>
ipq60xx bootcount script include /lib/functions that produce warning
when the script is enabled on image compilation. This script is already
included by /etc/rc.common hence it's not needed.
While at it also fix the format of the switch case.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert the Enterasys WS-AP3710i access point to use the simpleImage
wrapper.
This is necessary, as the bootlaoder does not align the DTB correctly
(and does not support altering the FDT loadaddress). Booting images with
kernels 5.15 and later can break depending on the alignment on the DTB
within the FIT image.
Signed-off-by: David Bauer <mail@david-bauer.net>
This refreshes the configuration on top of kernel 6.6 and activates it
as test kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Despite coming with multiple I2C EEPROMs supposedly dedicated for that
purpose, the BPi-R4 does not seem to have factory assigned MAC addresses.
Hence, just like for all other BPi boards, store a randomly generated
MAC address on first boot and derive WAN and Wi-Fi MAC addresses from
that as well. Not perfect, but better than random on every boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow selecting 6.1 as testing kernel on zynq.
Tested-by: Luis Araneda <luaraneda@gmail.com> # Zybo Z7-20
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Nick Hainke <vincent@systemli.org>
For this particualar device we get random MAC's for Wifi on each (re-)boot.
This is because art partition/pre caldata do not contain valid MAC addresses.
As we have now a new/better approach with ath11k_patch_mac we can use it for
this device too.
I'm using this approach for like two weeks and its working flawlessly.
Signed-off-by: Ulrich Stark <pwned-pixel@posteo.de>
qualcommax: IPQ807x: ZyXEL NBG7815: Fix random Wifi MAC
Changing order to 3/phy0/5G-1, 2/phy1/2G, 4/phy2/5G-2.
Signed-off-by: Ulrich Stark <pwned-pixel@posteo.de>
Enable USB 3.0 controller, disable USB 2.0 controller.
The USB 2.0 port on the AP-303H is actually connected to the USB 3.0
controller's HS phy. Enable the HS phy only, since the SS lanes are not
brought out to the connector.
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Use NVMEM to assign "factory sticker" MAC address to WAN ethernet
interface. Set LAN address to sticker + 1.
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Importing pending patch "net: dsa: mt7530: move MT753X_MTRAP operations
for MT7530" broke WAN connectivity on most MT7621 which use PHY-muxing
to hook up either port 0 or port 4 to GMAC1.
Remove it for now until the author submits a fixed version.
Fixes: https://github.com/openwrt/openwrt/issues/15279
Fixes: https://github.com/openwrt/openwrt/issues/15273
Fixes: d40691a5fb ("generic: 6.1, 6.6: mt7530: import pending patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The backports introduced in commit d40756563c ("kernel: backport
phylink changes from mainline Linux") broke the mv88e6xxx DSA driver.
A backport to fix this was added to the kirkwood target, but as it is
used in multiple targets, and there's a kmod package for it, the fix
should be in generic backports.
This fixes the switch on the WatchGuard Firebox M300 when running the
6.1 testing kernel.
There is no need to backport the fix for the 6.6 kernel, as it was
included in 6.6.5.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Set DEVICE_DTS_DIR to /qcom by default instead of limiting it to
TESTING_KERNEL since we moved 6.6 to default version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Set DEVICE_DTS_DIR to /qcom by default instead of limiting it to
TESTING_KERNEL since we moved 6.6 to default version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
