Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.
Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....
Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC - enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
The most common CPU governor in the OpenWRT project is currently ondemand (see
below). Switch mt7622 over to it as well.
Audit the code by running the following and then analyzing the results:
find -name 'config-5.*' -print0 | xargs -0 grep 'CONFIG_CPU_FREQ_DEFAULT_GOV.*=y'
ondemand: 16
performance: 5
schedutil: 5
userspace: 2
Build system: x86_64
Build-tested: ramips/mt7621
Signed-off-by: John Audia <graysky@archlinux.us>
Don't reply on mapped rootfs partition but rather just take what ever
has been set to the kernel cmdline root= parameter as a hint to decide
which media to install sysupgrade to on the BananaPi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* remove orphaned Kconfig symbol now that CONFIG_IIO is no longer
selected after commit ef8b935c95 ("mediatek: clean up mt7622 kernel config")
* select UBI fast-map feature to decrease boot time and keep the
number of spare blocks required in sync with U-Boot's expectations
(we got fast-map enabled in U-Boot)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When the v1 and v2 variants of the U6LR were introduced, the board
network config was not adapted to the new device names. Due to this, the
wrong network config is applied during initial boot. The resulting
config has lan, wan and a switch, while this device only has a single
ethernet interface without a switch.
Fix this by using a wildcard that matches all the variants.
Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Fixes: 5c8d3893a7 ("mediatek: new target ubnt_unifi-6-lr-v1-ubootmod")
Fixes: 31d86a1a11 ("mediatek: add Ubiquiti UniFi 6 LR v2 targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Instead of always including the XHCI driver in the kernel on all
MediaTek boards, selectively include the kernel module only on boards
which actually make use of USB functionality.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The newly introduced config symbol CONFIG_CMDLINE_OVERRIDE is only set
for mt7629 for now which breaks automated build on all other mediatek
subtargets. Make sure the symbol is configured as 'is not set' for all
remaining subtargets.
Fixes: c27279dc26 ("mediatek: add support for ipTIME A6004MX Add basic support for ipTIME A6004MX.")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It will be supported by the new filogic subtarget
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because
of its I2C dependency. Build it as a module and let buildroot handle
this config option instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Remove patches and configuration for Linux 5.10 which have been left
in the tree despite the target having been switched to Linux 5.15.
Fixes: c283defa88 ("mediatek: switch to 5.15")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set CONFIG_SCHED_MC in config-5.15 to have make the scheduler aware
of shared caches.
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch implements the spi-nand controller driver as an ECC-capable
spi-mem controller to use the upstream SPI-NAND driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Use ARMv8 Crypto Extensions for AES, ghash and sha256.
This results in a 16 times speed gain in speed for aes-128-ctr, 17x in
aes-128-gcm, and 9 times in sha256.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This commit add some enabled symbols to generic config.
LTO is only supported by clang compiler and therefore should
be disabled in the generic config instead of duplicating this
symbol in each target. CONFIG_LTO_NONE do this job.
The second group of symbols is enabled by the options available
in the generic config and is therefore added here:
* CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX,
* CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL,
* CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET.
The other symbols are disabled and should be in the generic config.
This commit also removes these symbols from subtargets.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.
SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A
Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.
However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.
Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5: 5eedf1632ac97bb5a6bb072c08603ed7)
2. Calculate telnet password from serial number and login
3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img)
Triggered by holding reset pin on powerup.
A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
X32 Pro is another product name for it in the Chinese market.
Specifications:
- SoC: MT7622B
- RAM: 256MB
- Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
- Ethernet: 5x1GbE
- Switch: MT7531BE
- WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
- 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
- 2Keys: Mesh button + Reset button
- UART: Marked J19 on board. 3.3v, 115200n1
- Power: 12V 2.5A
MAC addresses as verified by OEM firmware:
use address source
WAN *:F4 ethaddr@product_info
LAN *:F5
5g *:F6
2g *:F7
Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
dd if=/dev/mtd7 of=/tmp/firmware.bin
and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.
Recovery stock firmware:
1. Transfer the firmware.bin image to the device.
2. Flash the image with:
mtd write firmware.bin firmware
Signed-off-by: Langhua Ye <y1248289414@outlook.com>
Now that both, fw_printenv/fw_setenv and fwtool are always present
during stage2 sysupgrade, we no longer need to list them in
RAMFS_COPY_BIN and RAMFS_COPY_DATA in platform.sh.
Drop both variables as they are now unneeded.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530 and
MT7531. Fix some link up/down issues.
The errornous check for the PHY mode which broke things with MT7531
has been removed as suggested by patch
net: phy: mediatek: remove PHY mode check on MT7531
As a result, things are working fine now on MT7622+MT7531 as well.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
This reverts commit 8b4cba53a9.
This broke the mt7530 on Linksys e8450 (mt7622) for me.
[ 1.312943] mt7530 mdio-bus:00 lan1 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.320890] mt7530 mdio-bus:00 lan1 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 0
[ 1.331163] mt7530 mdio-bus:00 lan2 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.339085] mt7530 mdio-bus:00 lan2 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 1
[ 1.349321] mt7530 mdio-bus:00 lan3 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.357241] mt7530 mdio-bus:00 lan3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 2
[ 1.367452] mt7530 mdio-bus:00 lan4 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.375367] mt7530 mdio-bus:00 lan4 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 3
[ 1.385750] mt7530 mdio-bus:00 wan (uninitialized): failed to connect to PHY: -EINVAL
[ 1.393575] mt7530 mdio-bus:00 wan (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530.
Fix some link up/down issues.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Limit bmt remapping range to cover everything up to and including the kernel image,
use the rest of the flash area for ubi.
Fix partition table and sysupgrade support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable Aquantia Ethernet PHY driver as there is an AQR112C 2500Base-T
PHY in the Ubiquiti UniFi 6 LR access point.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
There's no such thing as ucidef_set_interfaces_lan. It's
ucidef_set_interface_lan.
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Similar to mt7623, also no longer use 'blockdev' and stop relying on
in-kernel partition parsers. Instead, strip off all metadata using
'fwtool' while writing the firmware image and scrape the number of
blocks written from 'dd', then use that block offset to stash the
configuration backup.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use find_mmc_part instead of previously introduced
get_partition_by_name which requires a custom kernel patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In case of the block device still being in use, re-reading the
partition table fails. In that case, abort sysupgrade to avoid
corrupting the just-written image because of wrong offsets caused
by failure to re-read the partition table.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable kernel options to allow loading device tree overlay via configfs
at runtime. This is useful for devboards like the BPi-R2 and BPi-R64
which got RasbPi-compatible 40-pin GPIO header which allow all sorts
of extensions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specifications:
- SoC: MT7622
- RAM: 512MB
- Flash: MX35LF1GE4AB 128MB SPI NAND
- Ethernet: RTL8367S 5x1GbE
- WiFi: 2.4G: MT7622 5G: MT7615N x2
- Other ports: USB3.0 x1
Flash instruction:
*important*: upgrade vendor firmware to at least V7.1cu.643_B20200521
1. hold the reset button and power on the device. wait for about 10s
before releasing the reset button.
2. upload sysupgrade.bin via u-boot recovery page on http://192.168.1.1
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This patch enables new spi-nand driver for mt7622 and mt7629.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
MT7622 provides are hardware RNG with upstream Linux driver. Enable
compilation of this driver to make use of the hardware RNG.
Signed-off-by: David Bauer <mail@david-bauer.net>
Build the driver for the in-SoC AHCI SATA host as module, just like for
the other subtargets. No board requires booting off SATA, so we don't
need to have it built-in. All boards with SATA support already select
kmod-ata-ahci-mtk which provides the module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
