Commit Graph

48516 Commits

Author SHA1 Message Date
Adrian Schmutzler
77e850fe76 ramips: tidy up MAC address setup for Linkit Smart and Omega2
Linkit Smart 7688 and Onion Omega 2(+) are one-port devices, and
have their port set to LAN by default. Setting up a WAN MAC address
for them doesn't make any sense, as no wan interface will be created
in uci config. Despite, these devices also set lan_mac in 02_network,
although mtd-mac-address sets a different address for the ethernet
interface in DTS.

Clean this up by moving the lan_mac value into DTS and dropping the
entries in 02_network completely. That way, the effective address
on the LAN interface should stay the same, but we get rid of the
extra (re)assignments.

As I don't have access to the devices, this does not tell anything
about whether 0x2e is actually a good choice, it just preserves
the existing assignment.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 13:33:26 +02:00
Tobias Welz
633ea0db0f ramips: WizFi630S use macs from factory partion
WIZnet WizFi630s has three mac addresses in the factory partition:
0x04 (also on the label), 0x28 for wan mac and 0x2e as lan mac.
All three macadresses are sequential series of addresses.
This is making use of them.

While at it, also add the label MAC address to 02_network.

MAC addresses as verified by OEM firmware:

use      interface   source
WLAN     ra0         factory 0x04 (label)
WAN      eth0.2      factory 0x28 (label + 1)
LAN      eth0.1      factory 0x2e (label + 2)

Signed-off-by: Tobias Welz <tw@wiznet.eu>
[fix sorting in 02_network, commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 13:33:26 +02:00
Tobias Welz
d0b229f553 ramips: correct WizFi630S pin mappings
WizFi630S had some pins changed in the release version of the board.
The run led, wps button and a slide switch where affected.
This patch is correcting this.
i2c is removed as it is sharing a pin with the run (system) led.
uart2 is enabled as it is also enabled in the OEM firmware.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-06 13:33:26 +02:00
Felix Fietkau
6c29604438 build: set up host command for egrep
It is used for the kernel build and uses GNU specific features

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 13:17:13 +02:00
Adrian Schmutzler
d1db1f4240 ipq40xx: refresh kernel 5.4 config
Refresh config with make kernel_oldconfig.

After d1a8217d87 ("kernel: clean-up build-configurable kernel
config symbols"), the routine wants to add an additional
CONFIG_CGROUPS (=n), which has been removed manually again, as
this seems unintended.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 12:51:51 +02:00
Felix Fietkau
3d731fc903 mac80211: merge performance improvement patches
Fix fq_codel performance issues
Add a new rx function for batch processing

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:43:25 +02:00
Felix Fietkau
431b177afa mediatek: fix mt7622-rfb1 board support
Make GPIO keys active-low.
Add DSA support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:42:43 +02:00
Felix Fietkau
b7727a8005 mac80211: fix AQL issues
- Remove bogus STA txq pending airtime underflow warning
- Improve tx airtime estimation for A-MPDU traffic

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:42:29 +02:00
Felix Fietkau
60f595daab binutils: update to version 2.34
Fixes perf on aarch64

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:42:16 +02:00
Felix Fietkau
bab0d1c33c mt76: update to 2020-07-22
7bc58ca2b375 mt76: add missing lock configuring coverage class
43febd452110 mt76: mt7615: fix lmac queue debugsfs entry
0b9975254694 mt76: mt7615: fix hw queue mapping
4058595e146e mt76: overwrite qid for non-bufferable mgmt frames
49c7131dd0c5 mt76: mt76x02: do not access uninitialized NAPI structs
f185d90ec51c update mt7915 firmware to the latest version
0ed6a335ebc2 mt76: mt7615: re-enable offloading of sequence number assignment
2a52eabbddc5 mt76: usb: rely on mt76_for_each_q_rx
90fc1d8614e1 mt76: mt7663: introduce ARP filter offload
b57223dd01b9 mt76: mt7615: fix up typo in Kconfig for MT7663U
ec4057d685c0 mt76: add script for generating single-sku device tree data
769b030de636 mt76: add functions for parsing rate power limits from DT
1d2aedb248d0 mt76: extend DT rate power limits to support 11ax devices
a3e17ff8e624 mt76: mt7615: implement support for using DT rate power limits
a48a4ae32d48 mt76: allow more channels, allowed in ETSI domain
869ba618ef54 mt76: fix include in pci.h
b1ddec840aa4 mt76: rely on register macros
d6d9a7ea428d mt76: add U-APSD support on AP side
ee13b78367db mt76: mt7615: fix EEPROM buffer size
82a94173b162 mt76: mt7915: add missing CONFIG_MAC80211_DEBUGFS
c0dbbd930d32 mt76: mt7615: add .set_tsf callback
84d54df76996 mt76: mt7915: add a fixed AC queue mapping
dacc2d29672d mt76: mt7915: add MU-MIMO support
1ce4660a0ea3 mt76: mt7915: use ieee80211_tx_queue_params to avoid open coded
53891242a682 mt76: mt7915: add support for DT rate power limits
b3a4d78914f6 mt76: mt7915: rework the flow of txpower setting
c6ea163c019b mt76: mt7915: directly read per-rate tx power from registers
8ae83adc73a8 mt76: mt7915: overwrite qid for non-bufferable mgmt frames
740b0bfdf279 mt76: mt76x2e: rename routines in pci.c
b5eee1b52234 mt76: mt7615: schedule tx tasklet and sta poll on mac tx free
72f34107248e mt76: mt7615: add support for accessing mapped registers via bus ops
46bc8a0b5347 mt76: mt7615: add support for accessing RF registers via MCU
882cec420609 mt76: mt7615: use full on-chip memory address for WF_PHY registers
b1ddb8e35ca2 mt76: vif_mask to struct mt76_phy
3a1ea7287eb2 mt76: add API for testmode support
d7467bc018e5 mt76: mt7615: implement testmode support
3ea5da1639fe add utility for using testmode support
6789a2db7246 mt7615: fix getting wideband RSSI in test mode
7941217ffe46 mt76: mt7915: remove unused parameters in mt7915_puts_rate_txpower()
13ab1d648684 mt76: mt7915: update HE capabilities
3f0e66dc25de mt76: mt76x2: fix pci suspend/resume on mt7612e
c605f2b6940b mt76: mt76x2u: enable HC-M7662BU1
ca2b797ee52d mt76: mt7915: avoid memcpy in rxv operation
dad3f93e8f6a mt76: mt7615: avoid polling in fw_own for mt7663
ec303bfad299 mt76: move mt76 workqueue in common code
0bf82270568a mt76: mt7615: add mt7615_pm_wake utility routine
091e9b5df6af mt76: mt7615: introduce mt7615_mutex_{acquire,release} utilities
e3850966d74c mt76: mt7615: wake device before accessing regmap in debugfs
e6dcb71d7992 mt76: mt7615: wake device before configuring hw keys
050f8cd9cbe7 mt76: mt7615: introduce pm_power_save delayed work
56779a6c7dec mt76: mt7615: wake device in mt7615_update_channel before access regmap
b0bcdd66ccaa mt76: mt7615: acquire driver_own before configuring device for suspend
58369fdce235 mt76: mt7615: wake device before performing freq scan
2c188db1f7c7 mt76: mt7615: add missing lock in mt7615_regd_notifier
6fdb20a025eb mt76: mt7615: run mt7615_mcu_set_wmm holding mt76 mutex
36a789c00e4f mt76: mt7615: run mt7615_mcu_set_roc holding mt76 mutex
b8cdce45c131 mt76: mt7615: wake device before pulling packets from mac80211 queues
82e8e0525d6c mt76: mt7615: wake device before pushing frames in mt7615_tx
65ccc40c14e1 mt76: mt7615: run mt7615_pm_wake in mt7615_mac_sta_{add,remove}
2107caf92e71 mt76: mt7615: check MT76_STATE_PM flag before accessing the device
28a2f5fa6eed mt76: mt7615: do not request {driver,fw}_own if already granted
94519eac69c3 mt76: mt7615: add runtime-pm knob in mt7615 debugfs
ccc90dafea66 mt76: mt7615: enable beacon hw filter for runtime-pm
29f2bebe1a1e mt76: mt7615: add idle-timeout knob in mt7615 debugfs
58057d1f232b mt76: mt7615: improve mt7615_driver_own reliability
a873b7c8e3de mt76: mt7663u: sync probe sampling with rate configuration
b469c59c616c mt76: mt7615: avoid scheduling runtime-pm during hw scan
f1ff52acb6a7 mt76: mt7615: reschedule ps work according to last activity
1f670a534451 mt76: mt7663u: fix memory leak in set key
afff00ad2b60 mt76: mt7663u: fix potential memory leak in mcu message handler
4c9309f47ddf mt76: mt7615: fix potential memory leak in mcu message handler
379445b4aa7f mt76: mt7915: potential array overflow in mt7915_mcu_tx_rate_report()
750797b61ba8 mt76: fix copy&paste error in mt76_testmode_cmd
f9a7a2f7dbc2 testmode: fix setting tx_power
1641aa201682 mt76: mt7615: fix mt7615_mcu_set_test_param set non-bool parameters
6838d002f9de mt76: mt7615: fix tx_frames setup
8c0a25d6a38c mt76: mt7615: take into account sdio bus configuring txwi
c0cbef79eb45 mt76: mt76u: add mt76_skb_adjust_pad utility routine
98412356c959 mt76: mt7615: sdio code must access rate/key regs in preocess context
fa16627d7e3a mt76: mt7615: introduce mt7663-usb-sdio-common module
bf88e70c7a68 mt76: introduce mt76_sdio module
aa97be8e02de mt76: mt7615: introduce mt7663s support
1eb8b7d689a3 mt76: testmode: fix tx_done accounting on enqueue failures
632ce698e8ee mt76: mt7615: fix antenna settings for test mode
4d2f622190b6 mt76: mt76s: move queue accounting in mt76s_tx_queue_skb
9a3723c8febc mt76: mt7915: fix potential memory leak in mcu message handler
88fa973f59c2 mt76: mt7615: fix possible memory leak in mt7615_mcu_wtbl_sta_add
2fff7d77befd mt76: mt76u: add missing release on skb in __mt76x02u_mcu_send_msg
b5df0fbb1847 mt7615: update firmware to version 20200629

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:41:50 +02:00
Felix Fietkau
b0f7ea2853 kernel: unify CONFIG_GPIO_SYSFS in kernel configs
Enable it for all platforms

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:37:04 +02:00
Felix Fietkau
eb155f755a build: make prefix mapping of debug information optional
Remapping the local build path in debug information makes debugging
using ./scripts/remote-gdb harder, because files no longer refer to the full
path on the build host.

For local builds, debug information does not need to be reproducible,
since it will be stripped out of packages anyway.

For buildbot builds, it makes sense to keep debug information reproducible,
since the full path is not needed (nor desired) anywhere.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:36:24 +02:00
Felix Fietkau
25e0ae6bfc mac80211: make cfg80211 testmode support optional (and disabled by default)
Testmode commands are typically only used for manufacturing or vendor specific
debugging features, so they should not be in the default image

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:36:23 +02:00
Jo-Philipp Wich
b92f54b919 openvpn: fix arguments passing to wrapped up and down scripts
With the introduction of the generic OpenVPN hotplug mechanism, wrapped
--up and --down scripts got the wrong amount and order of arguments passed,
breaking existing configurations and functionality.

Fix this issue by passing the same amount of arguments in the same expected
order as if the scripts were executed by the OpenVPN daemon directly.

Ref: https://github.com/openwrt/openwrt/pull/1596#issuecomment-668935156
Fixes: 8fe9940db6 ("openvpn: add generic hotplug mechanism")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-08-06 08:34:31 +02:00
Jo-Philipp Wich
34553e8cc9 add vfconfig
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-08-06 08:34:19 +02:00
Jo-Philipp Wich
96b87196b0 dsaconfig: introduce package for UCI configuration of VLAN filter rules
This package provides the necessary files to translate `config dsa_vlan`
and `config dsa_port` sections  of `/etc/config/network` into appropriate
bridge vlan filter rules.

The approach of the configuration is to bridge all DSA ports into a logical
bridge device, called "switch0" by default, and to set VLAN port membership,
tagging state and PVID as specified by UCI on each port and on the switch
bridge device itself, allowing logical interfaces to reference port VLAN
groups by using "switch0.N" as ifname, where N denotes the VLAN ID.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-08-06 08:34:19 +02:00
Alexey Dobrovolsky
4c73c34ec4 ramips: switch rt305x subtarget to kernel 5.4
RT3x5x seems to work fine with kernel 5.4. Set the default kernel
version to 5.4 to bring this to a broader audience.

Since 4 of 6 targets are on kernel 5.4 now, invert the kernel
version setup logic in Makefile/target.mk files.

Tested on ZyXEL Keenetic.

Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[invert version setup logic]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-05 23:27:35 +02:00
Tobias Welz
816973f42a ramips: enable flashing WizFi630S via OEM firmware
WIZnet WizFi630s board name is written slightly different it its OEM
OpenWrt firmware. This causes an incompatibility warning during flashing
with sysupgrade. This patch is adding the vendor board name to the
supported devices list to avoid this warning. For initial flashing you
can use sysupgrade via command line or luci beside of TFTP.
Do not keep the OEM configuration during sysupgrade.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-05 23:08:03 +02:00
Adrian Schmutzler
7c1c0a00fc ipq806x: use qcom-ipq8064-v1.0.dtsi from upstream
This uses upstream qcom-ipq8064-v1.0.dtsi and modifies it by patches
instead of keeping a local version. As a consequence:

- we use a part of the shared definitions there and update device
  DTS files accordingly
- we move additional stuff from our local v1.0.dtsi to the patch
- we drop partitions, LEDs and keys from the file as we will
  implement them differently anyway

Like with the previous patch, this follows the idea that a diff
from upstream might be easier to handle than a big file of our
own with different distribution pattern of properties.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-05 23:08:03 +02:00
Adrian Schmutzler
b7b7c2a6ad ipq806x: use qcom-ipq8064.dtsi from upstream
Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite
it with a full version of our own in the ipq806x target. About half of
the contents of our file are upstream content, the other half are local
improvements.

To prevent us from having a lot of code maintained twice in parallel,
this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our
local changes are arranged into three patches, the first pulling a
commit from upstream, the second doing a few small adjustments, and
the third adding all additional stuff.

This should get us the best of both worlds.

The property "ports-implemented" on sata@29000000 is moved to
2nd-level DTSI files as kernel defines it there as well.

While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to
include the kernel version where it's added upstream.

Even though this might look more complicated in the first place,
the aim is to bring our files closer to upstream, so we can benefit
from changes directly and vice-versa. After all, this drop about
650 lines just copied from the upstream DTSI file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-05 23:08:03 +02:00
Rafał Miłecki
3d167ed805 uhttpd: update to the latest master
212f836 ubus: rename JSON-RPC format related functions
628341f ubus: use local "blob_buf" in uh_ubus_handle_request_object()
9d663e7 ubus: use BLOBMSG_TYPE_UNSPEC for "params" JSON attribute
77d345e ubus: drop unused "obj" arguments
8d9e1fc ubus: parse "call" method params only for relevant call

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-05 15:49:03 +02:00
Tobias Welz
b735bbcb18 ramips: remove doublet entry in WizFi630S dts file
&wmac entry in WIZnet WizFi630S dts file was existing two times.
This is removing one of them.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-05 12:10:15 +02:00
Tobias Welz
36d4c2272e ramips: disable unused phy ports of WizFi630S
WIZnet WizFi630S is using only 3 of the phy ports. The unused phy ports
draw unnecessarily power. This is disabling the unused phy ports.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-05 12:10:15 +02:00
Rafał Miłecki
e47bec489f bcm47xx: switch to kernel 5.4
Switch, LEDs, USB, buttons, sysupgrade testedon BCM4706.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 15:51:08 +02:00
Petr Štetiar
80d360202f scripts: remove checkpatch.sh
That file was added accidentally in v3 of the patch and I haven't
properly reviewed that patch before pushing it.

Fixes: 656b562aff ("scripts: Add Buildbot dump-target-info.pl script")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-08-04 14:25:44 +02:00
Rafał Miłecki
7125323b81 bcm53xx: switch to kernel 5.4
Switch, USB, WiFi, buttons tested on BCM47094.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 13:28:56 +02:00
Rafał Miłecki
36c53e0dd2 bcm53xx: set HW_RANDOM_BCM2835=y
This enables Random Number Generator support on Northstar (described in
DT with brcm,bcm5301x-rng).

It's also a workaround for OpenWrt bug with kernel config causing:
Broadcom BCM2835/BCM63xx Random Number Generator support (HW_RANDOM_BCM2835) [Y/n/m/?] (NEW)

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 13:27:19 +02:00
Rafał Miłecki
c8c9876607 bcm53xx: update kernel 5.4 DTS to upstream 5.9 state
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 13:27:19 +02:00
Rafał Miłecki
b9cd55b88e bcm53xx: update kernel 5.4 config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 13:27:19 +02:00
Paul Spooren
656b562aff scripts: Add Buildbot dump-target-info.pl script
The script comes from buildbot.git[0] and is used to print available
targets and architectures, which are then build.

As the buildbot clones openwrt.git anyway, the script might as well live
here to be used for other cases as well, e.g. determining what
architectures are available when building Docker containers or show
developers an overview which architectures are used by which target.

It's called with either the parameter `architectures` or `targets`,
showing architectures followed by supported targets or targets, followed
by the supported architectures:

$ ./scripts/dump-target-info.pl architectures
aarch64_cortex-a53 bcm27xx/bcm2710 mediatek/mt7622 mvebu/cortexa53 sunxi/cortexa53
aarch64_cortex-a72 bcm27xx/bcm2711 mvebu/cortexa72
...

$ ./scripts/dump-target-info.pl targets
apm821xx/nand powerpc_464fp
apm821xx/sata powerpc_464fp
...

In the future the the script could be removed from the buildbot
repository and maintained only here.

Rename `dumpinfo.pl` to `dump-target-info.pl` to improve verbosity of
filename.

[0]: https://git.openwrt.org/?p=buildbot.git;a=blob;f=scripts/dumpinfo.pl;h=aa97f8d60379076a41b968402e9337cea824ece5;hb=HEAD

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-08-04 09:28:39 +02:00
Richard Fröhning
009e62c92c ramips: add support for TP-Link RE200 v3
TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button

Unverified:
- UART header on PCB (57600 8n1)

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

MAC address assignment has been done according to the RE200 v2.

The label MAC address matches the OpenWrt ethernet address.

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Recovery
--------

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

The device has not been opened for adding support. However, it is expected
that the behavior is similar to the RE200 v2. Instructions for serial console
and recovery may be checked out in commit 6d6f36ae78 ("ramips: add support
for TP-Link RE200 v2") or on the device's Wiki page.

Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[adjust commit title/message, sort support list]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 23:34:34 +02:00
Jason A. Donenfeld
80a6d3d4a2 wireguard: bump to 1.0.20200729
* compat: rhel 8.3 beta removed nf_nat_core.h
* compat: ipv6_dst_lookup_flow was ported to rhel 7.9 beta

This compat tag adds support for RHEL 8.3 beta and RHEL 7.9 beta, in addition
to RHEL 8.2 and RHEL 7.8. It also marks the first time that
<https://www.wireguard.com/build-status/> is all green for all RHEL kernels.
After quite a bit of trickery, we've finally got the RHEL kernels building
automatically.

* compat: allow override of depmod basedir

When building in an environment with a different modules install path, it's
not possible to override the depmod basedir flag by setting the DEPMODBASEDIR
environment variable.

* compat: add missing headers for ip_tunnel_parse_protocol

This fixes compilation with some unusual configurations.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2020-08-03 23:14:24 +02:00
Adrian Schmutzler
1deaf695ec ramips: fix/tidy up 4M tplink-v2-image flash layouts
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:

device         uboot    OEM firmware  OpenWrt (incl. config)
tl-wr840n-v5   0x20000  0x3c0000      0x3d0000
tl-wr841n-v14  0x10000  0x3d0000      0x3e0000

In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.

However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.

So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 12:17:08 +02:00
Adrian Schmutzler
18b7d87a8f kirkwood: get rid of BOARD_NAME and tidy up DEVICE_DTS
Since most of the DTS file names follow a common scheme now, let's
update the automatically generated DEVICE_DTS value and get rid
of some DEVICE_DTS and all BOARD_NAME entries for individual devices.

This should specifically make the job easier for developers adding
new devices, as they are not tempted to copy over BOARD_NAME anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 10:47:22 +02:00
Adrian Schmutzler
d168f14042 toolchain/binutils: remove versions 2.29.1 and 2.31.1
We currently support four versions of binutils in parallel. Let's
just keep the latest two and drop the older ones before the next
one comes around.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 10:44:10 +02:00
Adrian Schmutzler
50413e1ec8 package: replace remaining occurrences of ifconfig with ip
ifconfig is effectively deprecated for quite some time now. Let's
replace the remaining occurrences for packages by the
corresponding ip commands now.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 10:42:35 +02:00
Adrian Schmutzler
356866c481 target: replace remaining occurrences of ifconfig with ip
ifconfig is effectively deprecated for quite some time now. Let's
replace the remaining occurrences for our target setup by the
corresponding ip commands now.

Note that this does not touch ar71xx, as it will be dropped anyway,
and changing it would only make backports harder.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 10:42:04 +02:00
Adrian Schmutzler
1d9542c50e build: image: return sizes if check-size fails
Instead of just printing a warning that an image is too big, also
print both actual size and limit in the string:

WARNING: Image file somename.bin is too big: 2096101 > 1048576

Since the kernel size is checked via the same function (if
KERNEL_SIZE is specified), this will also apply to the kernel
image size check.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 10:40:32 +02:00
Sungbo Eo
c90db26e05 ar71xx: restore support for boot console with arbitrary baud rates
Commit 1bfbf2de6d ("ar71xx: serial: core: add support for boot console
with arbitrary baud rates") added support for arbitrary baud rates which
enabled 250000 baud rate for Yun. But the patch was not ported to kernel
4.9, and since then the kernel set its baud rate to 9600. This commit ports
the patch to kernel 4.14, thereby restoring the serial console of Yun.

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 18:10:06 +02:00
Sungbo Eo
a5e404d192 ar71xx: enable ethernet LED of Arduino Yun
Commit 05d73a2a73 enabled GPIO on ethernet LED, but proper LED setup was
not added then. This commit fixes it by reverting the change on the LED.

Fixes: 05d73a2a73 ("ar71xx: Arduino Yun board 'WLAN RST' button support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 16:34:21 +02:00
Sungbo Eo
58dc1d0637 ar71xx: fix sysupgrade for Arduino Yun
Commit bb46b635df changed its partition scheme, but sysupgrade image
validation still uses the old format. This commit fixes it so that
force flag is not needed for sysupgrade.

Fixes: bb46b635df ("ar71xx: move Arduino Yun to generic building code")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 16:34:21 +02:00
Sungbo Eo
43896dc0b0 Revert "ar71xx: fix Arduino Yun enabling of level shifters outputs"
This reverts commit 077253dd66.

The output enable pins should be disabled by default, and only enabled when
used. Otherwise unwanted conflicts might occur between MCU and SoC pins.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 16:34:21 +02:00
Adrian Schmutzler
93d37fad86 build: image: drop unused check-kernel-size recipe
The recipe check-kernel-size is not used in the entire tree. Instead,
we already check the size of the kernel image in Device/Build/kernel
in image.mk via check-size function if KERNEL_SIZE is defined.

Therefore, drop the function. Using it would be redundant anyway.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-02 15:54:43 +02:00
Paul Spooren
8d13198655 LICENSE: use updated GNU copy
The current LICENSE file contains some form feed (FF) characters instead
of recently popular line feed (LF) characters. Also update to the latest
address of the Free Software Foundation. Lastly center some captions, as
suggested by the official GNU LICENSE distribution[0].

Historical changes of GPL-2.0 LICENSE file are availalbe[1].

[0]: https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
[1]: https://github.com/pombredanne/gpl-history

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-08-02 15:54:43 +02:00
Adrian Schmutzler
b99623329c scripts/checkpatch.pl: fix README.md file name after rename
checkpatch.pl uses a list of files to detect the root OpenWrt
directory. This includes README, which has been renamed to
README.md in the previous commit.

Update the file name in checkpatch.pl to prevent errors like the
following when running the script:

   Must be run from the top-level dir. of a OpenWrt tree

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-02 15:51:39 +02:00
Paul Spooren
d0113711a3 README: port to 21st century
The README is no longer important to only developers but also users.
Reflect that by adding valuable information for everyone new to OpenWrt!

Sunshine

Signed-off-by: Paul Spooren <mail@aparcar.org>
[remove trailing whitespace and empty line at EOF]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-02 15:44:40 +02:00
Adrian Schmutzler
8a8ef4ed86 ath79/mikrotik: create shared device definitions for nor and nand
Move the image preparation and nand-utils package selection into
common device definitions for NOR/NAND devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-01 18:31:24 +02:00
Magnus Kroken
48a9d99a21 openvpn: revise sample configuration
Update the openvpn sample configurations to use modern options in favor
of deprecated ones, suggest more sane default settings and add some
warnings.

* Add tls_crypt and ncp_disable to the sample configuration
* Replace nsCertType with remote_cert_tls in client sample configuration
* Comment out "option compress", compression should not be preferred
* Advise 2048-bit Diffie-Hellman parameters by default
* Add warnings about compression and use of Blowfish (BF-CBC)

Signed-off-by: Magnus Kroken <mkroken@gmail.com>
2020-08-01 14:54:39 +01:00
Rui Salvaterra
9565c5726a uboot-envtools: ath79: add support for the Nanostation M (XM)
Tested on an AirGrid M2 (AG‑HP‑2G16).

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2020-08-01 14:54:39 +01:00
Rui Salvaterra
f2af32c20c wireguard-tools: allow compiling with MIPS16 instructions
The wg utility compiles and runs without issues in MIPS16 mode, despite setting
PKG_USE_MIPS16:=0 in the makefile. Let's remove this, allowing for a substantial
size reduction of the wg executable. Since wg is a just a configuration utility,
it shouldn't be performance-critical, as the crypto heavy-lifting is done on the
kernel side.

wg sizes for both modes:

MIPS32: 64309 bytes
MIPS16: 42501 bytes

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2020-08-01 14:54:39 +01:00