change meson binary to use py extension. Fixes issue with meson's
symbolextractor using the host python instead of the system one.
We intentionally use a .py extension here so that meson launches
additional python scripts with the same build host python interpreter as
itself is running under (and not the host package one once it becomes
available)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
By default CONFIG_BTRFS_FS_POSIX_ACL is disabled, it should be enabled
only when you enable CONFIG_FS_POSIX_ACL.
Right now, when you enable CONFIG_FS_POSIX_ACL it will enable
CONFIG_BTRFS_FS_POSIX_ACL, but it will be disabled once you install
kmod-btrfs. This should prevent it.
Btrfs has enabled by default ACL for mount option.
More details:
https://cateee.net/lkddb/web-lkddb/BTRFS_FS_POSIX_ACL.htmlhttps://btrfs.wiki.kernel.org/index.php/Manpage/btrfs(5)
Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Revert the SDC "CLK_SET_RATE_GATE" changes to the SDC clock regulator
structures.
See https://elinux.org/images/b/b8/Elc2013_Clement.pdf
> if ((clk->flags & CLK_SET_RATE_GATE) && clk->prepare_count) {
>
> For this particular clock, setting its rate is possible only if the
> clock is ungated (not yet prepared)
This fixes the MMC failing to initialize on newer ZyXEL NBG6817
hardware revisions with Kingston MMC. Older revisions should
hopefully be unaffected.
Check MMC hardware details with:
cd /sys/block/mmcblk0/device/ && \
tail -v cid date name manfid fwrev hwrev oemid rev
Known problematic MMC names (broken before this commit):
* M62704 (dated 12/2018) via myself
* M62704 (dated 11/2018) via Drake Stefani
Known unaffected MMC names (already working without this commit):
* S10004 (dated 12/2015) via slh
Without enabling dynamic debugging, this error manifests in the kernel
hardware serial console as the following:
[ 2.746605] mmc0: error -110 whilst initialising MMC card
[…trimmed other messages…]
[ 2.877832] Waiting for root device /dev/mmcblk0p5...
Enabling Linux dynamic kernel debugging provides additional messages.
For guidance, see the Linux kernel documentation:
https://www.kernel.org/doc/html/latest/admin-guide/dynamic-debug-howto.html
First, enable dynamic debugging in OpenWRT's configuration:
1. Run "make menuconfig"
2. Select "Global build settings --->"
3. Select "Kernel build options --->"
4. Enable "Compile the kernel with dynamic printk" via spacebar
5. Save and exit (arrow key to "Exit" until prompted to save, save)
Alternatively, set "CONFIG_KERNEL_DYNAMIC_DEBUG=y" in your .config.
Then, turn on dynamic debugging at boot:
Modify bootargs in
target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
to add…
bootargs = "[…existing bootargs…] dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8";
For example:
chosen {
- bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1";
+ bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1 dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8";
append-rootblock = "root=/dev/mmcblk0p";
Then, compile and flash the resulting build. If you are testing
before this commit on newer MMC hardware, be prepared to recover!
NOTE: If you have hardware serial console access, you don't need to
use TFTP recovery to change the active boot partition.
Reboot to working alternative partition via serial console:
1. Connect to hardware serial console
* See https://openwrt.org/toh/zyxel/nbg6817#serial
2. Interrupt boot at "Hit any key to stop autoboot:"
3. Run "ATSE NBG6817"
4. Copy the result (e.g. "001976FE4B04")
* Changes with **every boot** - can't reuse this
5. On your local system, run
"./zyxel-uboot-password-tool.sh <copied value here>"
* Example: "./zyxel-uboot-password-tool.sh 001976FE4B04"
6. Run the command provided by the password tool
* Example: "ATEN 1,910F129B"
* Changes with **every boot** - can't reuse this
7. Run "ATGU"
* You now have full u-boot shell until next boot - unlocking is
not remembered
8. Run either "run boot_mmc" (for booting partition set "FF") or
"run boot_mmc_1" (for booting partition set "01")
* These commands are not affected by dual-boot partition flags
NOTE: This will NOT set the dual-boot partition flag. You'll need to
fix that manually. The "nbg6817-dualboot" script may help:
https://github.com/pkgadd/nbg6817/blob/master/nbg6817-dualboot
zyxel-uboot-password-tool.sh - sourced from
commit 459c8c9ef8:
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ a ))
printf "ATEN 1,%X\n" $p
Kernel serial console log BEFORE commit with dynamic debug enabled:
[…trimmed…]
[ 3.171343] mmci-pl18x 12400000.sdcc: designer ID = 0x51
[ 3.171397] mmci-pl18x 12400000.sdcc: revision = 0x0
[ 3.175811] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz
[ 3.181134] mmci-pl18x 12400000.sdcc: No vqmmc regulator found
[ 3.186788] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio)
[ 3.192902] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2
[ 3.215609] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0
[ 3.227532] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v
[ 3.247518] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0
[…trimmed…]
[ 3.997725] mmc0: req done (CMD2): -110: 00000000 00000000 00000000 00000000
[ 4.003631] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000
[ 4.003659] mmc0: error -110 whilst initialising MMC card
[ 4.016481] mmc0: clock 0Hz busmode 2 powermode 0 cs 0 Vdd 0 width 1 timing 0
Notice how the initial clock is 52 MHz, which is incorrect - MMC
requires negotiation to enable higher speeds.
Kernel serial console log AFTER commit with dynamic debug enabled:
[…trimmed…]
[ 3.168996] mmci-pl18x 12400000.sdcc: designer ID = 0x51
[ 3.169051] mmci-pl18x 12400000.sdcc: revision = 0x0
[ 3.173492] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz
[ 3.178808] mmci-pl18x 12400000.sdcc: No vqmmc regulator found
[ 3.184702] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio)
[ 3.190573] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2
[ 3.217873] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0
[ 3.229250] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v
[ 3.249111] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0
[…trimmed…]
[ 4.392652] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000
[ 4.392785] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 1
[ 4.406554] mmc0: starting CMD6 arg 03b70201 flags 0000049d
[…trimmed…]
Now, the MMC properly initializes and later switches to high speed.
Thanks to:
* Ansuel for maintaining/help with the IPQ806x platform, kernel code
* slh for additional debugging and suggestions
* dwfreed for confirming newer MMC details, clock frequency
* robimarko for device driver debug printing help, clock debugging
* Drake for testing and confirmation with their own newer NBG6817
...and anyone else I missed!
Signed-off-by: Shane Synan <digitalcircuit36939@gmail.com>
Tested-by: Shane Synan <digitalcircuit36939@gmail.com>
BMT replaces nand-specific ops for erasing and writing, but the
mtk-snand driver only implements generic mtd api.
Replace erase, block_isbad, block_markbad in mtd_info for generic mtd
drivers.
Fixes: b600aee3ed ("mediatek: attach bmt to the new snand driver")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The following command checks if a instance of a service is running.
/etc/init.d/<service> running <instance>
In the variable `$@`, which is passed to the function
`service_running`, the first argument is always the `instance` which
should be checked. Because all other variables where removed from `$@`
with `shift`.
Before this change the first argument of `$@` was set to the `$service`
Variable. So the function does not work as expected. The `$service`
variable was always the instance which should be checked. This is not
what we want.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
ipTIME A3004NS-dual is a 2.4/5GHz band router, based on Mediatek MT7621.
Specifications:
- SoC: MT7621 (880MHz)
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7602E
- 5GHz : MT7612E
- Ethernet:
- 4x LAN
- 1x WAN
- USB: 1 * USB3.0 port
- UART:
- 3.3V, TX, RX, GND / 57600 8N1
Installation via web interface:
- 1. Flash Initramfs image using OEM Firmware's web GUI
- 2. Boot into OpenWrt and perform Sysupgrade with sysupgrade image.
Revert to stock firmware:
- 1. Boot into OpenWrt and perform Sysupgrade with OEM Stock Firmware image.
Signed-off-by: Yuchan Seo <hexagonwin@disroot.org>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Currently it is not possible to configure VLANs via LUCI on
tplink tl-mr3020-v3. This patch fixes switch topology for the
LUCI interface.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
[copied commit message from github PR]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In 20b09a2125 Lava LR-25G001 router have problem with two inactive
ethernet ports. JBOOT bootloader didn't configure ethernet devices by default.
The same situation was there. It is required to enable all phy ports.
This is fragment of stock bootlog:
switch reg write_athr offset=90, value=2b0
switch reg write_athr offset=8c, value=2b0
switch reg write_athr offset=88, value=2b0
switch reg write_athr offset=84, value=2b0
switch reg write_athr offset=80, value=2b0
This patch adds proper registers configuration ar8337 initvals.
0x2b0 value causes force flow control configuration, 0x1200 was used
instead (flow control config auto-neg with phy). [1]
When switch is now ok, let's fix port numeration too.
Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")
[1] https://github.com/openwrt/openwrt/pull/4806#issuecomment-982019858
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
introduce nvmem pre-cal + mac-address cells for both Wifis
and ethernet on the EZVIZ CS-W3-WD1200G EUP. This is one of
the few devices in which the correct mac adress is already
at the right place for Wifi, so no separate nvmem cell is
needed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
with current images, the device is no longer booting.
It gets stuck in the bootloader with "Config not available"
and drops to the uboot shell.
|flash_type: 0
|Hit any key to stop autoboot: 0
|SF: Detected MX25L12805D with page size 4 KiB, total 16 MiB
|Config not availabale
|(IPQ40xx) #
This is because the default bootcmd "bootipq" will only read
the first four MiB of the kernel image. With 5.10 the gzip'd
kernel is slightly larger. So the part of the FIT image which
had the configuration is cut off. Hence it can't find it.
To update the bootcmd, you have to attach the serial console
again and enter the following commands into the boot prompt:
# setenv bootcmd "sf probe; sf read 84000000 180000 600000; bootm"
# saveenv
# run bootcmd
This will allow booting kernels with up to six MiB. This also
allows us to drop the DEVICE_DTS_CONFIG hack we had to use.
Note:
uboot doesn't support LZMA. It fails with:
"Unimplemented compression type 3"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The itian sq201, raidsonic ib-4220-b and storlink sl93512r
can't boot from ext4. This is because the rootfstype in the
device-tree bootargs is set to "squashfs,jffs2". (And ext4
was not designed for raw NOR flash chips).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add the Embedded Wireless "Balin" platform, it is in ar71xx too
SoC: QCA AR9344 or AR9350
RAM: DDR2-RAM 64MBytes
Flash: SPI-NOR 16MBytes
WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
Ethernet: 3 x 10/100 Mb/s
USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
PCIe: MiniPCIe - 1 x lane PCIe 1.2
Button: 1 x Reset-Button
UART: 1 x Normal, 1 x High-Speed
JTAG: 1 x EJTAG
LED: 1 x Green Power/Status LED
GPIO: 10 x Input/Output multiplexed
The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade -n --force <image>" image directly in
vendor firmware. This resets the existing configurations back to
default!
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
[indent, led function+color properties, fix partition unit-address,
re-enable pcie port, mention button+led in commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The commented out code is not required, as the comment
indicates.
The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones. This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized. It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones. This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized. It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones. This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized. It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The recent changes to the maximum kernel size for Mamba and Venom
highlighted the fact that the old Mamba kernel size has been
hardcoded in linksys_get_root_magic() even for devices with
a different kernel/rootfs split.
The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones. This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized. It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
71e08471ab56 mt76: eeprom: fix return code on corrected bit-flips
9a8fc6636d83 mt76: move sar_capa configuration in common code
7cdbea1dc82a mt76: only access ieee80211_hdr after mt76_insert_ccmp_hdr
678071ef7029 mt76: mt7615: clear mcu error interrupt status on mt7663
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch adds supports for the GL-B2200 router.
Specifications:
- SOC: Qualcomm IPQ4019 ARM Quad-Core
- RAM: 512 MiB
- Flash: 16 MiB NOR - SPI0
- EMMC: 8GB EMMC
- ETH: Qualcomm QCA8075
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
- WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
- INPUT: Reset, WPS
- LED: Power, Internet
- UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
- UART2: On board with BLE module
- SPI1: On board socket for Zigbee module
Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.
What's working:
- WiFi 2G, 5G
- WPA2/WPA3
Not tested:
- Bluetooth LE/Zigbee
Credits goes to the original authors of this patch.
V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade
Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adds generic support for sysupgrading on eMMC-based devices.
Provide function emmc_do_upgrade and emmc_copy_config to be used in
/lib/upgrade/platform.sh instead of redundantly implementing the same
logic over and over again.
Similar to generic sysupgrade on NAND, use environment variables
CI_KERNPART, CI_ROOTPART and newly introduce CI_DATAPART to indicate
GPT partition names to be used. On devices with more than one MMC
block device, CI_ROOTDEV can be used to specify the MMC device for
partition name lookups.
Also allow to select block devices directly using EMMC_KERN_DEV,
EMMC_ROOT_DEV and EMMC_DATA_DEV, as using GPT partition names is not
always an option (e.g. when forced to use MBR).
To easily handle writing kernel and rootfs make use of sysupgrade.tar
format convention which is also already used for generic NAND support.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CC: Li Zhang <li.zhang@gl-inet.com>
CC: TruongSinh Tran-Nguyen <i@truongsinh.pro>
LHGG-60ad is IPQ4019 + wil6210 based.
Specification:
- Qualcomm IPQ4019 (717 MHz)
- 256 MB of RAM (DDR3L)
- 16 MB (SPI NOR) of flash
- 1x Gbit ethernet, 802.3af/at POE IN connected through AR8035.
- WLAN: wil6210 802.11ad PCI card
- No USB or SD card ports
- UART disabled
- 8x LEDs
Biggest news is the wil6210 PCI card.
Integration for its configuration and detection has already been taken
care of when adding support for TP-Link Talon AD7200.
However, signal quality is much lower than with stock firmware, so
probably additional board-specific data has to be provided to the
driver and is still missing at the moment.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[Fix Ethernet Interface]
Signed-off-by: Nick Hainke <vincent@systemli.org>
Added patch for GCC to fix compilation issues on MacOS arm64
The original commit message from Przemysław Buczkowski:
GCC: Patch for Apple Silicon compatibility
This patch fixes a linker error occuring when compiling
the cross-compiler on macOS and ARM64 architecture.
Adapted from:
https://github.com/richfelker/musl-cross-make/issues/116#issuecomment-823612404
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
Added patch for MacOS without 32 bit inodes support
(__DARWIN_ONLY_64_BIT_INO_T is true)
This patch based on discussion https://github.com/archmac/bootstrap/issues/4
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
a6451fea5a3d mt76: mt7615: improve wmm index allocation
1911486414dc mt76: mt7915: improve wmm index allocation
7998a41d1321 mt76: clear sta powersave flag after notifying driver
664475574438 mt76: mt7603: introduce SAR support
5c0da39c940b mt76: mt7915: introduce SAR support
77fc6c439a32 mt76: mt7603: improve reliability of tx powersave filtering
094b3d800835 firmware: update mt7663 rebb firmware to 20200904171623
25237b19bcc1 mt76: eeprom: tolerate corrected bit-flips
1463cb4c6ac2 mt76: mt7921: fix boolreturn.cocci warning
586bad6020f7 mt76: mt7921: use correct iftype data on 6GHz cap init
8ec95c910425 mt76: mt7921s: fix bus hang with wrong privilege
688e30c7d854 firmware: update mt7921 firmware to version 20211014
6fad970893dd mt76: fix key pointer overwrite in mt7921s_write_txwi/mt7663_usb_sdio_write_txwi
95acf972750c mt76: fix 802.3 RX fail by hdr_trans
3f402b0cf6c0 mt76: mt7921s: fix possible kernel crash due to invalid Rx count
929a03a8d65d mt76: connac: fix last_chan configuration in mt76_connac_mcu_rate_txpower_band
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update wifi firmware used for nanopi neo air, with
cypress-firmware-43430-sdio there is no wifi detected, as
brcmfmac-firmware-43430a0-sdio allow to acces to wifi.
Signed-off-by: Michel Promonet <michel.promonet@free.fr>
This results in setting format specific data (format info, extract
commands) in a single function. It should help maintaining sysupgrade
code.
This change has been tested on Asus GT-AC5300 and Netgear R8000P.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
List of supported formats grew over time and implementation got a bit
messy. There are multiple functions with format-specific parameters and
commands.
Refactor it by making platform_identify() setup all required info right
after detecting firmware format. This simplifies formats handling in
platform_other_check_image() and platform_do_upgrade() a lot.
This has been tested on:
1. SmartRG SR400ac (TRX): non-NAND sysupgrade
2. Netgear R8000 (CHK): NAND aware and standard sysupgrade-s
3. D-Link DIR-885L (Seama): NAND aware and standard sysupgrade-s
4. Luxul XWR-3150 (LXL): NAND aware and standard sysupgrade-s
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This patch is a revert of the upstream patch to Debian's ca-certificate
commit 033d52259172 ("mozilla/certdata2pem.py: print a warning for expired certificates.")
The reason is, that this change broke builds with the popular
Ubuntu 20.04 LTS (focal) releases which are shipping with an
older version of the python3-cryptography package that is not
compatible.
|Traceback (most recent call last):
| File "certdata2pem.py", line 125, in <module>
| cert = x509.load_der_x509_certificate(obj['CKA_VALUE'])
|TypeError: load_der_x509_certificate() missing 1 required positional argument: 'backend'
|make[5]: *** [Makefile:6: all] Error 1
...or if the python3-cryptography was missing all together:
|Traceback (most recent call last):
| File "/certdata2pem.py", line 31, in <module>
| from cryptography import x509
|ModuleNotFoundError: No module named 'cryptography'
More concerns were raised by Jo-Philipp Wich:
"We don't want the build to depend on the local system time anyway.
Right now it seems to be just a warning but I could imagine that
eventually certs are simply omitted of found to be expired at
build time which would break reproducibility."
Link: <https://github.com/openwrt/openwrt/commit/7c99085bd697>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Reported-by: Shane Synan <digitalcircuit36939@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The xway_legacy subtarget only supports 5 devices. Most compiled
switch drivers are unused by any of these devices. The same drivers
are compiled into the xway subtarget. They were probably copied
from there when creating this subtarget.
Switches used by devices:
Arcadyan ARV4518PWR01 Realtek RTL8306SD
Arcadyan ARV4518PWR01A Realtek RTL8306SD
Arcadyan ARV4520PW Infineon ADM6996I
Arcadyan ARV4525PW only PHY(IC+ IP101A)
Arcadyan ARV452CQW Realtek RTL8306
The CONFIG_ETHERNET_PACKET_MANGLE symbol has also been disabled,
as it is only needed by the driver for AR8216.
Reduces kernel size by 19.9 kB.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
We actually need to enclose the whole section of partitions in a
`partitions { ... }` to assign it a `compatible = "fixed-partitions";
otherwise the partition referred to by `hwinfo` won't be registered
when bringing up MTD partitions, for example as per:
- <https://forum.openwrt.org/t/tp-link-c2600-missing-default-mac-mtd-partition-in-snapshot/103945/6>
- commit e2b03c16eb ("ipq806x: add missing enclosing partitions block for TP-Link C2600")'
Fixes: 8ec21d6bb2 ("mpc85xx: convert mtd-mac-address to nvmem implementation")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[minor beautification]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This target does not activate CONFIG_PCI kernel configuration option, do
not activate the PCI feature. This will deactivate some PCI drivers
which are not building without PCI support in the kernel.
If PCI_SUPPORT or PCIE_SUPPORT are activated in the kernel configuration
the feature flag will be automatically set by the build system again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Deactivate all the symbols of the B53 DSA driver in the generic kernel
configuration. Multiple targets are now using this drivers and they
only need some of the options.
This fixes the bcm4908 build which didn't deactivate all of the options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
