The mac80211-hwsim and the Intel iwlwifi driver support ieee80211ax, add
the missing DRIVER_11AX_SUPPORT dependency too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 576b62712f)
Fix a authentication bypass problem in WPA Enterprise client mode. See
here for details: https://www.top10vpn.com/research/wifi-vulnerabilities/
This problem was assigned CVE-2023-52160
This problem was fixed in upstream hostapd in June 2023. Hostapd used in
OpenWrt 23.05 and later already contains this fix..
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When `log.showSignature` is set, it causes the `SOURCE_DATE_EPOCH` to
include a textual signature description on OpenPGP-signed commits,
because Git prints the description into stdout. This then causes some
scripts to fail because they cannot parse the date from the variable.
Adding an explicit `--no-show-signature` prevents the signatures from
being displayed even when one has Git configured to show them by
default, fixing the scripts.
Signed-off-by: Oto Šťáva <oto.stava@gmail.com>
(cherry picked from commit 1e93208bd2)
This update mac80211 to version 5.15.148-1. This includes multiple
bugfixes. Some of these bugfixes are fixing security relevant bugs.
The following patch was integrated into upstream Linux:
package/kernel/mac80211/patches/subsys/352-wifi-mac80211-fix-invalid-drv_sta_pre_rcu_remove-cal.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ubiquiti Rocket M XW is a single-band, 2x2:2 external Wi-Fi AP, with optional
GPS receiver, with two external RP-SMA antenna connections, based on
AR9342 SoC. Two band variants exists, for 2.4GHz and 5GHz band, usable
with the same image.
Specs:
- CPU: Atheros AR9342 MIPS SoC at 535MHz
- RAM: 64MB DDR400
- ROM: 8MB SPI-NOR in SO16W package, MX25L6408E
- Wi-Fi Atheros AR9342 built-in 2x2:2 radio
- Ethernet: Atheros AR8035 PHY, limited to 100Mbps speeds due to
magnetics
- Power: 24V passive PoE input.
Installation: please refer to Ubiquiti Bullet M2HP for documentation.
The device runs with exactly same image as the Bullet, and after fixes
in preceding commit, is fully functional again. Add the alternative name
to the build system.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 54387fddea)
Since commit 6f2e1b7485 ("ath79: disable delays on AT803X config init")
Ubiquiti XW boards equipped with AR8035 PHY suffered from lack of
outbound traffic on the Ethernet port. This was caused by the fact, the
U-boot has set this during boot and it wasn't reset by the PHY driver,
and the corresponding setting in device tree was wrong.
Set the 'phy-mode = "rgmii-txid"' at the ð0, and drop this property
from PHY node, as it is not parsed there. This causes the device to
connect using Ethernet once again.
Fixes: db4b6535f8 ("ath79: Add support for Ubiquity Bullet M (XW)")
Fixes: 6f2e1b7485 ("ath79: disable delays on AT803X config init")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit a9b2ba4d7b)
Onboard AR8035 PHY supports 1000Base-T operation, but onboard
Ethernet magnetics do not. Reduce advertised link speeds to 100Mbps and
lower.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit d406777fb1)
This release of Mbed TLS provides bug fixes and minor enhancements. This
release includes fixes for following security issues:
* Timing side channel in private key RSA operations (CVE-2024-23170)
Mbed TLS is vulnerable to a timing side channel in private key RSA
operations. This side channel could be sufficient for an attacker to
recover the plaintext. A local attacker or a remote attacker who is
close to the victim on the network might have precise enough timing
measurements to exploit this. It requires the attacker to send a large
number of messages for decryption.
* Buffer overflow in mbedtls_x509_set_extension() (CVE-2024-23775)
When writing x509 extensions we failed to validate inputs passed in to
mbedtls_x509_set_extension(), which could result in an integer overflow,
causing a zero-length buffer to be allocated to hold the extension. The
extension would then be copied into the buffer, causing a heap buffer
overflow.
Fixes: CVE-2024-23170, CVE-2024-23775
References: https://mbed-tls.readthedocs.io/en/latest/security-advisories/mbedtls-security-advisory-2024-01-1/
References: https://mbed-tls.readthedocs.io/en/latest/security-advisories/mbedtls-security-advisory-2024-01-2/
Signed-off-by: orangepizza <tjtncks@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [formal fixes]
(cherry picked from commit 920414ca88)
(cherry picked from commit b5c728948c)
Read back the reset register in order to flush the cache. This fixes
spurious reboot hangs on TP-Link TL-WDR3600 and TL-WDR4300 with Zentel
DRAM chips.
This issue was fixed in the past, but switching to the reset-driver
specific implementation removed the cache barrier which was previously
implicitly added by reading back the register in question.
Link: freifunk-gluon/gluon#2904
Link: openwrt#13043
Link: https://dev.archive.openwrt.org/ticket/17839
Link: f8a7bfe1cb2c ("MIPS: ath79: fix system restart")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2fe8ecd880)
The ESW core needs to be reset together with FE core, so after the
relevant reset controller lines are moved under FE, drop rst_esw and all
related code, which would not execute anyway, because rst_esw would be
NULL. While at that, ensure that if reset line for EPHY cannot be
claimed, a proper error message is reported.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Co-developed-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[Split out of the bigger commit, provide commit mesage, refactor error
handling]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit f393ffcac1)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Failing to do so will cause the DMA engine to not initialize properly
and fail to forward packets between them, and in some cases will cause
spurious transmission with size exceeding allowed packet size, causing a
kernel panic.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[Provide commit description, split into logical changes]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit f87b66507e)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Failing to do so will cause the DMA engine to not initialize properly
and fail to forward packets between them, and in some cases will cause
spurious transmission with size exceeding allowed packet size, causing a
kernel panic.
This is behaviour of downstream driver as well, however I
haven't observed bug reports about this SoC in the wild, so this
commit's purpose is to align this chip with all other SoC's - MT7620
were already using this arrangement.
Fixes: #9284
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit fc92fecfc7)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Failing to do so will cause the DMA engine to not initialize properly
and fail to forward packets between them, and in some cases will cause
spurious transmission with size exceeding allowed packet size, causing a
kernel panic.
This is behaviour of downstream driver as well, however I
haven't observed bug reports about this SoC in the wild, so this
commit's purpose is to align this chip with all other SoC's - MT7620
were already using this arrangement.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit c5a399f372)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Failing to do so will cause the DMA engine to not initialize properly
and fail to forward packets between them, and in some cases will cause
spurious transmission with size exceeding allowed packet size, causing a
kernel panic.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[Provide commit description, split into logical changes]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 8d75b1de0f)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Enabling the FE core too early causes the system to hang during boot
uncondtionally, after the reset is released. Increate it to 1-1.2ms
range.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[Split previous commit, provide rationale]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 7eb0458c1f)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Use devm_reset_control_array_get_exclusive to register multiple
reset lines in FE driver. This is required to reattach ESW reset to FE
driver again, based on device tree bindings.
While at that, remove unused fe_priv.rst_ppe field, and add error
message if getting the reset fails.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Co-developed-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[Split out of the bigger commit, provide commit mesage, refactor error
handling]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 3f1be8edee)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Fix typo calling lua53 instead of lua5.3 for Package Default definition.
This cause only missing description of the package and doesn't cause
any build regression.
Fixes: c52ca08d40 ("lua5.3: build shared library")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 25e215c14e)
[ fix conflict with changed URL value ]
General specification:
- SoC Type: MediaTek MT7620N (580MHz)
- ROM: 8 MB SPI-NOR (W25Q64FV)
- RAM: 64 MB DDR (M13S5121632A)
- Switch: MediaTek MT7530
- Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
- Wireless 2.4 GHz: b/g/n
- Buttons: 1 button (RESET)
- Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5
- Power: 12 VDC, 1.0 A
Flash by the native uploader in 2 stages:
1. Use the native uploader to flash an initramfs image. Choose
openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by
"Administration/Management/Firmware update/Choose File" in vendor's
web interface (ip: 192.168.1.10, login: Admin, password: Admin).
Wait ~160 seconds.
2. Flash a sysupgrade image via the initramfs image. Choose
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
file by "System/Backup/Flash Firmware/Flash image..." in
LuCI web interface (ip: 192.168.1.1, login: root, no password).
Wait ~240 seconds.
Flash by U-Boot TFTP method:
1. Configure your PC with IP 192.168.1.131
2. Set up TFTP server and put the
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
image on your PC
3. Connect serial port (57600 8N1) and turn on the router.
Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2:
Load system code then write to Flash via TFTP.").
Press Y key when show "Warning!! Erase Linux in Flash then burn
new one. Are you sure? (Y/N)"
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.131) ==:192.168.1.131
Input Linux Kernel filename () ==:
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
3. Wait ~120 seconds to complete flashing
Signed-off-by: Alexey Bartenev <41exey@proton.me>
(cherry picked from commit 7796c2d7ef)
[Fix merging conflict]
Signed-off-by: Alexey Bartenev <41exey@proton.me>
When firmware-utils was converted to use cmake, the dependency was not
updated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit b71affaf8b)
Saves a little bit of time when compiling cmake.
Added patches to fix searching liblzma and zlib. The issue is that
because pkgconfig is not used, the system libraries get used.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 3848cf458e)
Allows to set expat as a dependency to cmake and save on compilation
time.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 89df3589e6)
Changes:
9dc0800 wireless-regdb: Update regulatory rules for Philippines (PH)
111ba89 wireless-regdb: Update regulatory rules for Egypt (EG) from March 2022 guidelines
ae1421f wireless-regdb: Update regulatory info for Türkiye (TR)
20e5b73 wireless-regdb: Update regulatory rules for Australia (AU) for June 2023
991b1ef wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
(cherry picked from commit 0e13363de6)
Backport didn't include changes to mkubntimage invocation, which allowed
to pass arguments. This in result produces broken routerstation factory
images, which have kernel embedded as kernel partition instead of LZMA
loader.
Fixes: #13260
Fixes: 8e09f9ffc3 ("ath79: switch some RedBoot based devices to OKLI loader")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Add new function to dump-targer-info.pl to DUMP devices provided a
matching target/subtarget.
Example:
./scripts/dump-targer-info.pl devices ipq806x/generic
will produce the sorted list of devices defined in the following format:
device_id device_name
Devices may have alternative names, the script will dump each
alternative name in the same line of device_id.
Following the pattern:
device_id "PRIMARY DEVICE NAME" "ALT0 DEVICE NAME" "ALT1 DEVICE NAME" ...
Example:
tplink_ad7200 "TP-Link AD7200 v1/v2" "TP-Link Talon AD7200 v1/v2"
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 943c153cdd)
With the case of asking an invalid version that is too big, getver.sh
might return an invalid output in the form of HEAD~-2260475641.
This is caused by BASE_REV - GET_REV using a negative number.
Prevent this by checking if BASE_REV - GET_REV actually return 0 or a
positive number and set REV variable accordingly. With the following
change, invalid revision number will result in unknown printed instead
of the invalid HEAD~-NUMBERS output.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 9e49e0a6c4)
Also channel 7 for 2.4GHz can be set to HT40PLUS. Permit this and add it
to the list of the channels.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit b1c7b1bd67)
[ rework for openwrt-22.03 ]
noscan option for mesh was broken and actually never applied.
This is caused by a typo where ssid->noscan value is check instead of
conf->noscan resulting in the logic swapped and broken.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 1b5ea2e199)
[ rework for openwrt-22.03 ]
noscan option was changed to hostapd_noscan but the entry in
wpa_supplicant was never updated resulting in the noscan option actually
never set.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 1070fbce6e)
[ rework for openwrt-22.03 ]
A package may run git as part of its build process, and if the package
source code is not from a git checkout, then git may traverse up the
directory tree to find buildroot's repository directory (.git).
For instance, Poetry Core, a Python build backend, will read the
contents of .gitignore for paths to exclude when creating a Python
package. If it finds buildroot's .gitignore file, then Poetry Core will
exclude all of the package's files[1].
This exports GIT_CEILING_DIRECTORIES for both package and host builds so
that git will not traverse beyond $(BUILD_DIR)/$(BUILD_DIR_HOST).
[1]: https://github.com/python-poetry/poetry/issues/5547
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
(cherry picked from commit f597f34f3a)
