- implement multiqueue via qdma hardware shaper to deal with ports with different speeds
- implement hardware DSA untagging
- add NETIF_F_ALL_TSO to reduce unnecessary segmentation
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The patch "210-pinctrl-mediatek-add-support-for-MT7986-SoC.patch" and
"212-clk-mediatek-add-mt7986-clock-support.patch" are upstreamed.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The patches "191-arm64-dts-mt7622-specify-the-L2-cache-topology.patch"
and "192-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch" are
upstreamed to 5.19.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The patch enabling hardware flow offloading support on the MT7623 SoC
has been merged upstream as of Linux 5.13. Remove our local patch which
wrongly got forward-ported and now actually enables hardware flow
offloading for the MT2701 SoC family (unsupported in OpenWrt).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The use of the adc_oe value stored in the efuse has been dropped in
MediaTek's SDK during a recent refactorization of the temperature
calculation formula. Don't ignore this offset value and again include
it in raw-to-deg-celsius calculation.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add dependency to '32k' ADC clock so it is always enabled for thermal
and raw access to ADC values. This allows to remove the patch for the
ADC driver and reduce the patch adding thermal support for MT7986 to
only add the new efuse layout and temperature decoding for V3.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch headers and description for pending patch.
Add version tag to patch already merged upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Raising the temperatures for passive and active trips. @VA1DER
proposed at issue 9396 to remove passive trip. This commit relates to
his suggestion.
Without this patch. the CPU will be throttled all the way down to 98MHz
if the temperature rises even a degree above the trip point, and it was
further discovered that if the internal temperature of the device is
above the first trip point temperature when it boots then it will start
in a throttled state and even
$ echo disabled > /sys/class/thermal/thermal_zone0/mode
will have no effect.
The patch increases the passive trip point and active cooling map. The
throttling temperature will then be at 77°C and 82°C, which is still a
low enough temperature for ARM devices to not be in the real danger
zone, and gives some operational headroom.
Signed-off-by: Bruno Umuarama <anonimou_eu@hotmail.com>
* set correct clocks for PWM to work.
* MT7986 PWM does have the 26MHz-clock-select, set that in patch
* drop useless 'passive' trip point in thermal zone
* extend pwm-fan to have 3 active operating points
* set reasonable trip points in thermal zone
* invert pwm-fan operating points and set shorter period to allow
less noisy operation of the PWM fan of the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for hardware I2C and PWM units found in the Filogic SoCs
as well as the CPU thermal support.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patches from mtk-openwrt-feeds (MTK SDK) to support reading
t-phy settings affecting PCIe as well as USB2 and USB3 from efuse.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow byte-wise access to mtk-efuse as some drivers require that.
Patch imported from mtk-openwrt-feeds (MTK SDK).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware:
SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core)
RAM: DDR3 128MB
Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB)
WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver
Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4)
UART: [GND, RX, TX, 3.3V] (115200)
Installation:
- Flash recovery image with TFTP recovery
Revert to stock firmware:
- Flash stock firmware with TFTP recovery
TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1
Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
The 213 patch is missing filename suffix. Fix it.
Fixes: dabcaac ("mediatek: add mt7986 soc support to the target")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The patch 921-mt7986-add-mmc-support.patch introduced by commit
dabcaac443 ("mediatek: add mt7986 soc support to the target") has never
been applied in a way that it would have any effect as it actually
created a file target/linux/generic/patches-5.15/... in the kernel tree
and was probably a patch intended to be applied to openwrt.git instead
of being put into kernel patches folder as a file.
As an upstream commit from vanilla Linux also adding support for MT7986
to the mtk-sd driver has already been included we can remove that old
patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The introduction of the new Airoha target has left the tree in an
unfresh state. Refresh patches to improve that situation.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport generic phylink validate series and make use of it for
mtk_eth_soc Ethernet driver as well as mt7530 DSA driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Older MT7623 ARMv7 SoC as well as new Filogic platforms come with
inside-secure,safexcel-eip97 units. Enable them in DTS and select the
driver kernel module by default on those platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It will be supported by the new filogic subtarget
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix the wps button to prevent wrongly detected recovery procedures.
In the official banana pi r64 git the wps button is set to
GPIO_ACTIVE_LOW and not GPIO_ACTIVE_HIGH.
Import patch to fix on boot unwanted recovery entering:
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- failsafe button wps was pressed -
- failsafe -
Signed-off-by: Nick Hainke <vincent@systemli.org>
Last attempt on this has a typo and doen't work.
It seems that this is a common problem occurring on every kernel bump,
so let's enforce arch timer support for mt7623 with a patch instead.
Fixes: 9a22943eb2 ("mediatek: 5.15: re-enable arch timer on MT7623 as well")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch implements the spi-nand controller driver as an ECC-capable
spi-mem controller to use the upstream SPI-NAND driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
the OOB layout in MTK SNFI uses the 2nd byte, and anything using OOB
will make the block a bad-block in spi-nand driver.
Hack it for now. We need a proper solution upstream.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Adresses of device tree nodes are typically noted without the '0x'
prefix. While having the '0x' prefix doesn't hurt when using Linux,
more recent versions of U-Boot will add a duplicate ramoops node as a
simple string compare is used to check if the node is already present.
Remove the '0x' prefix to avoid the kernel warning resulting from
U-Boot adding a dupplicate pstore/ramoops node.
See also https://lists.denx.de/pipermail/u-boot/2022-April/481810.html
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
