Commit Graph

3814 Commits

Author SHA1 Message Date
Koen Vandeputte
1cf2495d48 ar71xx: make IRQ fixes target specific
Move the IRQ fix from generic to ar71xx specific.
Other targets like ath79 have specific pathes to delete this code.
This resulted in a build failure on ath79

While at it, wipe the 4.19 version, as ar71xx will never reach this.

Fixes: 530f76708cef ("ar71xx: Fix potentially missed IRQ handling during
dispatch")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-14 17:11:45 +02:00
Koen Vandeputte
713561a10b ar71xx: fix potential IRQ misses during dispatch for qca953x
If both interrupts are set in the current implementation
only the 1st will be handled and the 2nd will be skipped
due to the "if else" condition.

Fix this by using the same approach as done for QCA955x
just below it.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-13 16:40:29 +02:00
Koen Vandeputte
7489ea85a2 Revert "ar71xx: use platform code for qca955x usb0 init"
This reverts commit 5b98061bb1.

As Piotr Dymacz pointed out:

In QCA MIPS based WiSOCs, for first USB interface,
device/host mode can be selected _only_ in hardware
see description of 57c641ba6e

QCA955x and QCA9563, second USB can be switched to device
mode in software (tested and confirmed on real hardware).

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-12 00:15:59 +02:00
Tomislav Požega
191c3e49b9 ar71xx: qca955x pci init/reset fixes
Current ar724x code does the reset only on single pci bus, and
in case of qca9558 writes the wrong register (0x10 vs 0x0c).
This change allows the reset of second pci bus, commonly used in
Archer C7 devices, in case host controller is stuck in reset.
If the resetting controller on boot can solve any other issue it
can be enabled unconditionally by removing reset check before
ar724x_pci_hw_init is called.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
[refreshed to apply cleanly]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-11 09:47:49 +02:00
Tomislav Požega
e8350c998b ar71xx: enable ddr wb flush on qca955x
Enable flushing of write buffers on qca955x. GPL code has 0x88 reg
defined for PCI flush which is likely an error since the device
freezes on boot. So use DS default value 0xA8 for PCI flush.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
2019-09-11 09:47:49 +02:00
Tomislav Požega
5b98061bb1 ar71xx: use platform code for qca955x usb0 init
Switch from ci_usb_setup to generic platform initialization of
usb0 port.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
2019-09-11 09:47:49 +02:00
Rafał Miłecki
a858db3136 treewide: sysupgrade: use $UPGRADE_BACKUP to check for backup
Now that $UPGRADE_BACKUP is set conditionally there is no need to check
the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-11 09:05:35 +02:00
Rafał Miłecki
641f6b6c26 treewide: use new procd sysupgrade $UPGRADE_BACKUP variable
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.

This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-05 23:33:19 +02:00
Rafał Miłecki
1078de96e3 treewide: fix invalid UPGRADE_OPT_SAVE_CONFIG spellings
That was a result of accidentally running "sed" twice on some files.

Fixes: 5797fe84a3 ("treewide: replace remaining (not working now) $SAVE_CONFIG uses")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-05 08:55:15 +02:00
Rafał Miłecki
5797fe84a3 treewide: replace remaining (not working now) $SAVE_CONFIG uses
This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG

Fixes: b534ba9611 ("base-files: pass "save_config" option to the "sysupgrade" method")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-05 08:43:24 +02:00
Tomasz Maciej Nowak
8b4109c2b4 ar71xx: sysupgrade: accept ath79 combined-image
There is md5 sum of whole image embedded in combined-image header which
is checked on sysupgrade. The check will fail for ath79 images which
may have embedded metadata. This is because metadata are appended after
the combined image is created. To allow smooth transition from ar71xx to
ath79, strip metadata before calculating md5 sum for whole image.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-09-01 00:12:02 +02:00
Michal Cieslakiewicz
dddb43775f ar71xx: WNR2200: remove redundant GPIO for WLAN LED
Without this patch, an extra entry appears for AR9287 GPIO
that duplicates WLAN LED but in fact drives nothing:

gpiochip1: GPIOs 502-511, ath9k-phy0:
 gpio-502 (                    |netgear:blue:wlan   ) out hi
 gpio-503 (                    |netgear:amber:test  ) out hi
 gpio-504 (                    |netgear:green:power ) out lo
 gpio-505 (                    |rfkill              ) in  hi
 gpio-507 (                    |wps                 ) in  hi
 gpio-508 (                    |reset               ) in  hi
 gpio-510 (                    |ath9k-phy0          ) out hi <===!

The pin pointed above is default LED GPIO (8) for AR9287.
For WNR2200 it is not connected anywhere - pin 0 drives blue WLAN
LED instead - but initialization code is missing that information.

This fix calls ap9x_pci_setup_wmac_led_pin() function at device
setup, forcing WLAN LED pin to be 0 and removing redundant entry.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-08-31 12:08:23 +02:00
Koen Vandeputte
81d0da1186 ar71xx/ath79: ag71xx: dont fetch the same var again
tx_size was just declared above and set to BIT(tx->order)
Use the declaration instead, which could avoid a pointer deref

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
e773838813 ar71xx: ag71xx: use base address value directly from the source
This brings the code more inline with the ath79 flavour

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
19ed799bdc ar71xx: ag71xx: make use of managed dev API simplifying code
Backport of a4eef43a12 ("ath79: ag71xx: replace alloc_etherdev with devm_alloc_etherdev")
combined with the initial changes from John Crispin.

Simplifies the code a lot by using the Managed dev API.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
4d40c0edd4 ar71xx: ag71xx: replace ag71xx_get_phy_if_mode_name with phy_modes()
Backport of f73b2d64ed ("ath79: ag71xx: replace ag71xx_get_phy_if_mode_name() with phy_modes()")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
e18724b907 ar71xx: ag71xx: pass correct device pointer to dma
Backport of 4eaa3626a8 ("ath79: ag71xx: pass correct device pointer to dma functions")

While 4.14 does not contain the warnings,
it still makes sense to use the proper pointers here.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
662922068d ar71xx/ath79: ag71xx: get ring_mask consistent
All other instances of this identical declaration fetch the
value directly from the ring_order.

Also do it here.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
e10b163247 ar71xx: ag71xx: add missing register writes
These are added in ath79, but were not backported here

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Adrian Schmutzler
b133e466b0
treewide: convert WiFi caldata size and offset to hexadecimal
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.

This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.

Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).

Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-14 12:36:37 +02:00
Adrian Schmutzler
75bfc393ba treewide: convert MAC address location offsets to hexadecimal
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.

This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.

(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)

Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-14 12:10:12 +02:00
Koen Vandeputte
2a08bf3656 ar71xx: ag71xx: init rings with GFP_KERNEL
ar71xx got lost during final rebase ..

Fixes: b417a0c48d ("ar71xx/ath79: ag71xx: init rings with GFP_KERNEL")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-09 18:51:07 +02:00
Koen Vandeputte
6ced31c320 ar71xx/ath79: ag71xx: fix sleep in atomic
When enabling atomic-sleep-debugging options in the kernel,
following splat is seen when disabling the interface (which happens on boot):

[   10.892878] eth0: link down
[   10.896788] BUG: sleeping function called from invalid context at net/core/dev.c:5563
[   10.904730] in_atomic(): 1, irqs_disabled(): 1, pid: 425, name: ip
[   10.911004] 2 locks held by ip/425:
[   10.914539]  #0:  (rtnl_mutex){....}, at: [<80377474>] rtnetlink_rcv_msg+0x2d8/0x380
[   10.922441]  #1:  (&(&ag->lock)->rlock){....}, at: [<80330158>] ag71xx_hw_disable+0x24/0x94
[   10.930976] CPU: 0 PID: 425 Comm: ip Not tainted 4.14.136 #0
[   10.936716] Stack : 805e0000 80589228 80557404 876998ec 80610000 80610000 87cdcafc 805b5327
[   10.945233]         80551534 000001a9 8061386c 87699ccc 87cfb180 00000001 876998a0 84f70903
[   10.953751]         00000000 00000000 80b00000 8769979c 6a7407fa 00000000 00000007 00000000
[   10.962270]         000000b7 16d0954a 000000b6 00000000 80000000 87cb658c 87cb65b0 00000001
[   10.970787]         8046f97c 87699ccc 87cfb180 87ff2810 00000003 802ce724 0806e098 80610000
[   10.979306]         ...
[   10.981797] Call Trace:
[   10.984287] [<8006cb0c>] show_stack+0x58/0x100
[   10.988814] [<800aab34>] ___might_sleep+0x100/0x120
[   10.993774] [<8035c434>] napi_disable+0x30/0xd8
[   10.998377] [<80330198>] ag71xx_hw_disable+0x64/0x94
[   11.003418] [<8033069c>] ag71xx_stop+0x24/0x38
[   11.007959] [<80359e30>] __dev_close_many+0xcc/0x104
[   11.013009] [<80362eac>] __dev_change_flags+0xc8/0x1ac
[   11.018227] [<80362fb8>] dev_change_flags+0x28/0x70
[   11.023182] [<80376890>] do_setlink+0x31c/0x91c
[   11.027786] [<80379360>] rtnl_newlink+0x3ec/0x7f8
[   11.032563] [<80377498>] rtnetlink_rcv_msg+0x2fc/0x380
[   11.037799] [<8039a734>] netlink_rcv_skb+0xd4/0x178
[   11.042754] [<80399d10>] netlink_unicast+0x168/0x250
[   11.047796] [<8039a2d4>] netlink_sendmsg+0x3d8/0x434
[   11.052841] [<8033f0e4>] ___sys_sendmsg+0x1dc/0x290
[   11.057794] [<80340140>] __sys_sendmsg+0x54/0x84
[   11.062495] [<8007212c>] syscall_common+0x34/0x58

This is caused by calling napi_disable() while holding the spinlock.

Fix it by omitting the spinlock, which is not required here
Extensively tested on GL-MiFi, RB-912 and RB-922 hardware

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-09 18:30:41 +02:00
Adrian Schmutzler
8d83a4f545 tplink-safeloader: increase kernel partition for CPE/WBSx10v1
This is a preparation for ath79 support of the CPE210/CPE510 v1.
Kernel size is chosen equal to the latest update for CPE610 v1.

This also updates the partition size in ar71xx target, so code
remains consistent if someone looks up the device. Since CPE210,
CPE510, WBS210 and WBS510 (all v1) share the same partition
layout definition, and are on deprecated target anyway, this
changes them all at once.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-07 18:04:03 +02:00
Leon M. George
c070662980 ar71xx: wpj531: fix SIG1/RSS1 LED GPIO
In commit 6c937df749 ("ar71xx: wpj531: fix GPIOs for LED") wrong GPIO
13 for SIG1/RSS1 LED was commited, the correct GPIO number for this LED
is 12.

It's listed in "Hardware Guide - wpj531 7A06 (02/07/2019)" as GPIO12/RSS1
on the LED header and same GPIO 12 is used in the vendor's SDK as well.

Fixes: 6c937df749 ("ar71xx: wpj531: fix GPIOs for LED")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit subject/message facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-08-04 22:37:15 +02:00
David Bauer
cb49e46a8a ar71xx: fix HiveAP 121 PLL for 1000M
The Aerohive HiveAP 121 has the wrong PLL value set for Gigabit speeds,
leading to packet-loss. 10M and 100M work fine.

This commit sets the Gigabit Ethernet PLL value to the correct value,
fixing packet loss.

Confirmed with iperf and floodping.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-01 21:27:47 +02:00
Koen Vandeputte
845b2a1cfe ar71xx: really fix Mikrotik board detection
commit e09da0169a ("ar71xx: fix Mikrotik board detection")
was generated based on testing a rb-912 board, on which detection failed.

Testing on more hardware shows something fun:

machine	: MikroTik RouterBOARD 922UAGS-5HPacD
machine	: Mikrotik RouterBOARD 912UAG-5HPnD

Both lowercase and uppercase are used.
So ensure we support both now ..

Fixes: e09da0169a ("ar71xx: fix Mikrotik board detection")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-01 12:10:02 +02:00
Koen Vandeputte
1d2b2e744e ar71xx: fix nand init issues on some rb2011 devices
While flashing lots of RB2011 devices, I noticed that
some of them refused to boot properly, failing over the NAND parameters.

Checking in detail shows that some device seem to use another NAND flash
which only support standard 2048-byte pages, without 512-byte subpage support.

This commit disables usage of these small subpage completely.

Advantages:
- Both NAND's with(out) subpage support are working now
- The nand speed increases a bit (measured roughly 1%) in typical usecases

Disadvantages:
- The maximum storage capacity decreases by ~0.2%
as small changes can consume a full page (2048 bytes) now.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-07-31 16:53:41 +02:00
Koen Vandeputte
e09da0169a ar71xx: fix Mikrotik board detection
Fix a typo in the machine type being extracted from /proc/cpuinfo
which causes all Mikrotik board to be undetected properly.

This lead to sysupgrade issues and probably some others too.

Fixes: acf2b6c888 ("ar71xx: base-files: fix board detect on new MikroTik devices")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-07-29 10:13:45 +02:00
Tomislav Požega
65762cdd22 ar71xx: fix WLAN LED names for Archer C7
Update WLAN LED colour identifier for both interfaces on Archer C7

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
2019-07-25 07:48:10 +02:00
Tomislav Požega
a73934fc9a ar71xx: fix system LED names on Archer C5/C7
Move system LED board definitions of Archer C5/C7 to reflect
actual system LED colour used

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
2019-07-25 07:48:10 +02:00
Tomislav Požega
c79c001b59 ar71xx: Archer C7 v1 LED names and RFKILL fixes
All leds on these boards are green. v1 has RFKILL GPIO 23 for production
units (it had GPIO 13 only for test phase units, and these are rather
very rare to find). As for the previous attempt to fix this and revert
due to WDR boards have blue leds, it was wrong: WDR board does not use
common setup (false).

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
2019-07-25 07:48:10 +02:00
Tomislav Požega
fd5aa19480 ar71xx: update qca-usb-quirks patch
Base address for USB0 has changed from 0x18116c94 on AR934X
to 0x18116d94 on QCA9558. CP Typo remained for years here...

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
2019-07-25 07:48:10 +02:00
Rafał Miłecki
1cbe0d659c treewide: sysupgrade: get rid of platform_nand_pre_upgrade()
1) nand_do_upgrade() is always called by a target code
2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade()

It means there is no need for the platform_nand_pre_upgrade() callback
at all. All code that was present there could bo moved & simplly called
by a target right before the nand_do_upgrade().

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-22 14:27:37 +02:00
Rafał Miłecki
8b4bc7abe0 treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()
stage2 passes image path to platform_do_upgrade() as an argument so it
can be simply accessed using $1

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-17 08:05:38 +02:00
Rafał Miłecki
20452a8db9 ar71xx: get rid of platform_pre_upgrade()
The only step between platform_pre_upgrade() and platform_do_upgrade()
is switching to ramdisk. It should be fine to "mtd erase firmware" from
the later callback and get rid of the first one.

This change wasn't tested on affected target but identical code logic
was verified to work as expected on brcm47xx with initramfs firmware.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-16 19:02:49 +02:00
Etienne Champetier
2a7519e29d ar71xx: enable SGMII fixup on Mikrotik wAP AC
fixes intermittent loss of connectivity on 1Gbit port, with log message:
> 803x_aneg_done: SGMII link is not ok

Thanks to David Bauer for pointing me in the right direction.
I just had to figure out the right bus_id, which you find in this log:
> ag71xx ag71xx.1: connected to PHY at gpio-1:00 [uid=004dd074,
  driver=Atheros 8031 ethernet]

Fixes FS#2236

Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
[Wrapped commit message - Fixed whitespace erors]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-16 16:54:50 +02:00
W. Michael Petullo
8c7d6c47a7 ar71xx: fix ath79/rb4xx IRQ initialization on kernel 4.14
Apply the same approach as in commit 3b53d6fdbc ("ar71xx: fix pci irq
init on kernel 4.14") to fix IRQ initialization for ath79-based chipsets
on rb4xx.

Ref: PR#2182
Acked-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: W. Michael Petullo <mike@flyn.org>
[commit ref fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-03 07:45:00 +02:00
Koen Vandeputte
4589f23943 kernel: bump 4.14 to 4.14.129
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-24 16:36:30 +02:00
Koen Vandeputte
1e3487b359 kernel: bump 4.14 to 4.14.127
Refreshed all patches.

Fixes:

- CVE-2019-11479
- CVE-2019-11478
- CVE-2019-11477

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-18 14:47:53 +02:00
Petr Štetiar
016d1eb1f9 ar71xx: make target source-only
Lets make it really explicit, that we should now focus only on ath79 in
order to make it ready for next release, where ar71xx is going to be
removed for good.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-17 09:42:37 +02:00
Henryk Heisig
acf2b6c888 ar71xx: base-files: fix board detect on new MikroTik devices
Move all MikroTik devices to new function to increase script execution
speed.

Machine name in new version of MikroTik RouterBOARD devices add "RB"
before model name:

 Old machine name: MikroTik RouterBOARD 951Ui-2nD
 New:              MikroTik RouterBOARD RB951Ui-2nD

So this patch should fix it for all currently supported MikroTik boards.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[rebased,commit message facelift,script fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[spotted missing 922UAGS-5HPacD]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-17 09:42:37 +02:00
Koen Vandeputte
a7e68927d0 kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)
Refreshed all patches.

This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297

Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch

Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-12 15:04:09 +02:00
Petr Štetiar
971d358579 ar71xx: ag71xx: update ethtool support
Remove references to broken and mostly deprecated phy_ethtool_ioctl, use
new {s,g}et_link_ksettings and add nway_reset which was previously
handled in phy_ethtool_ioctl.

Cc: John Crispin <john@phrozen.org>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=1982
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Petr Štetiar
eafe0611d9 ar71xx: ag71xx: remove unused SIOCETHTOOL ioctl handling
This ioctl is currently routed through generic interface code:

  dev_ioctl
    dev_ethtool
      __ethtool_get_link_ksettings
        phy_ethtool_ioctl

Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Koen Vandeputte
8f6fd53db9 kernel: bump 4.14 to 4.14.122
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-03 12:40:53 +02:00
Alexander Couzens
8357b8131c
ar71xx: wr940 v4/v6: correct lan interface mac address
The vendor firmware only uses two mac addresses, the mac address on the
label and the label + 1. While checking multiple devices, all labels have
even mac addresses. Concluding only 2 address are assigned to a device.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2019-05-21 14:53:45 +02:00
Petr Štetiar
73b21559ce ar71xx: set mib-poll-interval on devices with ar8xxx switch
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.

So this patch sets mib-poll-interval to 500ms on devices which are using
ar8xxx switch LEDs trigger, as the same value was set for built in
switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch").

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-05-20 21:19:48 +02:00
Adrian Schmutzler
f32e05c541 ar71xx: Fix network setup for TP-Link Archer C25 v1
Network for the Archer C25 v1 is set up without switch for no
obvious reason. The LED setup is even done switch-based.

This patch changes network setup so a switch is created.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-05-15 13:34:24 +02:00
Koen Vandeputte
09050b6fe2 kernel: bump 4.14 to 4.14.118
Refreshed all patches.

Remove upstreamed:
- 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch

Altered:
- 143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-13 19:17:41 +02:00
Joachim Fünfer
edf1d6264b ar71xx: fix failsafe interface for TL-WR940nv6
Switches failsafe mode interface from WAN to LAN ports.

Tested on TL-WR940Nv6.0 and TL-WR940Nv6.1

Signed-off-by: Joachim Fünfer <joachim.fuenfer@stusta.net>
2019-05-05 21:11:01 +02:00
Rosy Song
3b4c44aa8b ar71xx: mute script error in ar922x-led-fix script
This commit fixes following script error in syslog:

 cat: can't open '/sys/devices/platform/ehci-platform/usb1/1-1/1-1.2/1-1.2:1.4/ieee80211/phy*/name': No such file or directory
 sh: add: unknown operand
 sh: add: unknown operand

Signed-off-by: Rosy Song <rosysong@rosinson.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[commit subject and message tweaks]
2019-05-05 21:11:01 +02:00
Koen Vandeputte
b765f4be40 kernel: bump 4.14 to 4.14.114
Refreshed all patches.

Altered patches:
- 150-bridge_allow_receiption_on_disabled_port.patch
- 201-extra_optimization.patch

Remove upstreamed:
- 022-0006-crypto-crypto4xx-properly-set-IV-after-de-and-encryp.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-02 12:59:26 +02:00
Koen Vandeputte
e40050d104 ar71xx: add support for Mikrotik RouterBOARD 2011UiAS-2HnD r2
This board got a new hardware revision, without any change in functionality.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-23 13:22:31 +02:00
Koen Vandeputte
da5bd73d70 kernel: bump 4.14 to 4.14.112
Refreshed all patches.

New symbol:
- CONFIG_LDISC_AUTOLOAD

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-22 21:15:17 +02:00
Adrian Schmutzler
93d23aced2 ar71xx: Correct MAC address for WAN interface of Archer C7 v5
This device shares the network config with v4, thus the WAN MAC
also needs to be fixed the same way. However, the partition
where the MAC address resides has been changed.

Based on: https://github.com/openwrt/openwrt/pull/1726

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:05 +02:00
Adrian Schmutzler
9aa8f87d27 ar71xx: Add "info" partition for TP-Link Archer C7 v5
This adds the "info" MTD partition, as it is specified in the
ath79 DTS:
https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_archer-c7-v5.dts#L35

This is required to set the WAN MAC address, as it is build based
on the LAN MAC address, which in turn has to be read from the
"info" partition:
https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_archer-c7-v5.dts#L35

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Petr Štetiar
31ea08a64b ar71xx: ag71xx: Fix broken networking on some devices (FS#2177)
It was reported, that latest ar71xx builds have broken networking on
TP-Link TL-WPA8630 and Nanostation M5 XW devices and that by reverting
the offending commit, everything is back to normal.

Fixes: d3506d1 ("ar71xx: ag71xx: fix compile error when enabling debug")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
0f8cdc28af ar71xx: Add support for Ubiquity Bullet M (XW)
CPU: AR9342 SoC
RAM:     64 MB DDR2
Flash:    8 MB NOR SPI
Ports:  100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART:     1 UART on PCB marked as J1 with 115200 8N1 config
LEDs:       Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:    Reset

UART connection details

  .---------------------------------.
  |                                 |
[ETH]          J1                 [ANT]
  |    o VCC o RX o TX o GND        |
  `---------------------------------'

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin

Tested only on Bullet M2HP.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
6009b3fd58 ar71xx: ubnt-m-xw: Fix factory image flashing using TFTP recovery
This is backport of the same functionality in ath79, from commit
 d42a7c469 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP
             recovery method")

Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:

 All future airOS versions will be signed in this way and not allow
 unsigned firmware to be loaded except via TFTP.

U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:

 Hit any key to stop autoboot:  0
 Setting default IP 192.168.1.20
 Starting TFTP server...
 Receiving file from 192.168.1.25:38438
 Received 4981148 bytes
 Firmware check failed! (1)

By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:

 Received 3801500 bytes
 Firmware Version: XW.ar934x.v6.0.4-42.OpenWrt-r9766+2-be42e44
 Setting U-Boot environment variables
 Un-Protected 1 sectors
 Erasing Flash.... done

Patch provided by AREDN[3] project, tested on Bullet M2 XW.

1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Koen Vandeputte
5387bc9cbb kernel: bump 4.14 to 4.14.111
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-08 14:53:39 +02:00
Robert Marko
99f6f2c0b8 ar71xx: Add support for TP-Link CPE210 v3
Looks identical to the v2.

This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[Rebased, adjusted for separate tplink-safeloader entry, dynamic partitioning]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-02 02:09:58 +02:00
Adrian Schmutzler
a2a972b2cf ar71xx: Use dynamic partitions for TP-Link CPE210 v2
This is also helpful to add support in ath79.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-02 02:08:37 +02:00
Petr Štetiar
0a67e84bae ar71xx: ens202ext: Fix whitespace issues
I've missed leading whitespace issues in the original patch, so fixing
it in this commit. Thanks to pepe2k for letting me know.

Fixes: d260813d ("ar71xx: ens202ext: Fix VLAN switch")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-01 12:07:09 +02:00
Michael Pratt
d260813d09 ar71xx: ens202ext: Fix VLAN switch
The target ENS202EXT was just recently added right before the stable
release of Openwrt 18.

It flashes fine, but the physical switch is almost impossible to use
until you have a VLAN set up. Tested on two devices.

The actual problem is that eth0 represents nothing for whatever reason.
In other words, both WAN and LAN are running from eth1. There may be an
underlying problem in the build, but for now, I assume that this is
correct and that a VLAN switch is an appropriate fix.

Also, it's virtually impossible to get the switch running right through
LuCI. It is one thing to get a switch to appear, but attempting to
configure it breaks the whole thing. The VLAN has to be set up
perfectly, otherwise, interfaces will not start up, and one is forced to
reset settings, OR, the new LuCI feature kicks in and reverses any
steps. It is extremely difficult to determine which virtual ports
correspond to which physical ethernet ports without being able to set up
the switch in LuCI.

Temporary Workaround: followed directions here
[openwrt/luci#867](https://github.com/openwrt/luci/issues/867)

Reviewed-by: Marty Plummer <hanetzer@startmail.com>
Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[commit author fix, subject fix, message text wrap]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-31 20:58:51 +02:00
Koen Vandeputte
e1444ab59c ar71xx: add support for MikroTik RouterBOARD 922UAGS-5HPacD
This patch adds support for the MikroTik RouterBOARD 922UAGS-5HPacD
with a built-in 802.11ac High-Power radio (31dBm).

See https://mikrotik.com/product/RB922UAGS-5HPacD for more info.

Specifications:
- SoC: Qualcomm Atheros QCA9557 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9882 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V
- SFP: 1x host
- USB: 1x 2.0 type A
- PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems)
- SIM slot: 1x mini-SIM

Working:
- Board/system detection
- NAND storage detection
- PCIe
- USB: Type A & mini PCIe
- Wireless
- Ethernet
- LED's (excl. SFP and RSSI levels)
- Reset button
- Sysupgrade

Not working:
- SFP cage

Installation:

- Boot vmlinux-initramfs image via BOOTP/TFTP and then flash sysupgrade
image using "sysupgrade -n"

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-03-26 18:01:47 +01:00
Koen Vandeputte
0304e76cd1 kernel: bump 4.14 to 4.14.107
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-22 18:14:28 +01:00
Xavier Douville
5ac974f214 ar71xx: Add support for Mikrotik RB SXT 2nD r3
The Mikrotik RouterBOARD SXT 2nD r3 is an outdoor WiFi AP / CPE
with a single 2.4 GHz radio and a 100 Mbps Ethernet port.
The device similar to the SXT 2nD r2, but it has SPI NOR flash instead
of NAND flash.

Hardware
--------
CPU:   Atheros AR9344 (600 MHz)
RAM:   64 MiB
FLASH: 16 MiB SPI NOR W25Q128
ETH:   1x 100 Mbps Atheros AG71xx
WiFi: 2T2R 802.11b/g/n (ath9k)
Power: Passive PoE 8-30 V

Installation instructions:

1. Boot openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf using a
   DHCP+TFTP server.
2. Erase the "firmware" partition using the mtd command. This should
   no longer be required once this patch is merged.
3. Use sysupgrade to install to flash. The file
   openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin
   should be used.

Signed-off-by: Xavier Douville <github@douville.org>
2019-03-22 00:40:29 +01:00
Aubrey McIntosh, PhD
34113999ef ar71xx: Remove ath10k packages from archer-c7-v1 (fixes FS#1743)
ath10k_pci driver crashes once loaded and causes boot loops on this
device as 5GHz radio QCA9880-AR1A shipped with this router is broken.
It's not possible to fix this problem in software, miniPCIe radio has to
be replaced.

We could've probably fixed crashing of the ath10k driver by reverting
following upstream commit:

 commit 1a7fecb766c83dace747f42b25bbb544b00a0163
 Author: Michal Kazior <michal.kazior@tieto.com>
 Date:   Sat Jan 24 12:14:48 2015 +0200

    ath10k: reset chip before reading chip_id in probe

but it's not worth the effort as it wouldn't make that 5GHz radio usable
anyway. So it seems more convenient to just remove the crashing driver
and provide bootable images, as I believe, that a router that is working
but degraded is better than a router that will not work.

For details please see discussions in PR[1] and in FS#1743[2].

1. https://github.com/openwrt/openwrt/pull/1349
2. https://bugs.openwrt.org/index.php?do=details&task_id=1743

Signed-off-by: Aubrey McIntosh, PhD <aubrey.mcintosh@utexas.edu>
[subject and commit message tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-21 02:04:57 +01:00
Koen Vandeputte
a8cfef6c45 kernel: bump 4.14 to 4.14.106
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-18 10:02:51 +01:00
Adrian Schmutzler
26f7cf8ac3 ar71xx: Speed up mtd extraction in ar71xx.sh
Although the amount of data read here is smaller than for the
caldata, there still might be some speed gain compared to reading
bytewise. And there is no harm ...

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-03-13 16:27:41 +01:00
Adrian Schmutzler
51fb186cb3 ar71xx: Speed up caldata/eeprom handling
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.

This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.

Speed comparison @ TP-Link TL-WDR4300 (just manually) results
in a time reduction by three orders of magnitude (99.9 %).

> time dd if=/dev/mtd3 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096
4096+0 records in
4096+0 records out
real    0m 15.85s
user    0m 0.06s
sys     0m 13.28s

> time dd if=/dev/mtd3 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes
1+0 records in
1+0 records out
real    0m 0.02s
user    0m 0.00s
sys     0m 0.02s

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-03-13 16:27:41 +01:00
Mantas Pucka
fe591f2fe2 ar71xx: enable QCA955x SGMII fixup on Rambutan
fixes intermittent loss of connectivity on 1Gbit port, with
log message:

  803x_aneg_done: SGMII link is not ok

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2019-03-06 22:02:56 +01:00
Koen Vandeputte
d3506d1bc1 ar71xx: ag71xx: fix compile error when enabling debug
Starting from kernel 4.5, phy_id needs to be fetched from a different location.

not doing so results in this compile error:

drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c: In function 'ag71xx_phy_connect_multi':
drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c:133:35: error: 'struct mdio_device' has no member named 'phy_id'
    ag->mii_bus->mdio_map[phy_addr]->phy_id);
                                   ^
./include/linux/printk.h:137:18: note: in definition of macro 'no_printk'
    printk(fmt, ##__VA_ARGS__); \
                  ^~~~~~~~~~~
drivers/net/ethernet/atheros/ag71xx/ag71xx.h:72:27: note: in expansion of macro 'pr_debug'
 #define DBG(fmt, args...) pr_debug(fmt, ## args)
                           ^~~~~~~~
drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c:130:3: note: in expansion of macro 'DBG'
   DBG("%s: PHY found at %s, uid=%08x\n",
   ^~~
scripts/Makefile.build:326: recipe for target 'drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.o' failed

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-05 13:19:43 +01:00
David Santamaría Rogado
e65f935de9 ar71xx: Change led trigger from usbdev to usbport
This patch changes all the legacy usbdev leds triggers
to the use usbport. The problem is that the usbdev triggers
get applied as usbport in sysfs but LuCI gets confused and
is not able to show the configuration with usbdev. More
information can be found in the PR:
<https://github.com/openwrt/openwrt/pull/1819>

Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[extended commit message]
2019-02-28 11:34:48 +01:00
Andreas Ziegler
53c46b504c ar71xx: GL.iNet AR300M family: correct LED definitions
remove USB as this is no LED but power control
rename WiFi LED with correct color red (like in stock firmware)
set middle LED to be used for LAN link/activity

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
2019-02-26 23:20:04 +01:00
Adrian Schmutzler
319c5d7c49 ar71xx: Fix 5 GHz MAC address for Archer C60 v2
Looks like C60 v2 needs the MAC address to be calculated
manually, while the C60 v1 gets it correctly without manual
interference.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-02-17 18:22:39 +01:00
Paul Wassi
78277ec162 ar71xx: fix TL-MR3220-v2 switch port order
Fix the switch port order for proper display on high
level interfaces.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
341311f319 ar71xx: fix TL-WR741ND-v4 switch port order
Fix the switch port order for proper display on high
level interfaces.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Koen Vandeputte
8c9f255ce5 ar71xx: add rssileds for xw devices
Commit 7ebbbda293 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication")
adds support for using the RSSI strenght via LEDS.

The rssileds package addition got lost during altering the patch.
Add it again to fix this.

Fixes: 7ebbbda293 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-11 09:24:11 +01:00
Lech Perczak
7ebbbda293 ar71xx: ubnt-(xm,xw): fix LED RSSI indication
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti XM and XW family, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.

Also add the required package for this.

While at that, remove coefficients needed for PWM LEDs, as XM and XW
boards do not support PWM LEDs.

Tested-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[Squashed commits + remove custom device_packages + slighty rewrite the commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-08 17:27:47 +01:00
Julien Rabier
6570f3c93a ar71xx: fix RB941-2nD detection
Some hAP lite routers aren't detected because
/proc/cpuinfo shows "RouterBOARD RB941-2nD"
instead of "RouterBOARD 941-2nD".

Fix that.

Signed-off-by: Julien Rabier <taziden@flexiden.org>
[Alter string to include all flavours + slight rewrite of commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-08 17:27:47 +01:00
Edoardo Scaglia
077253dd66 ar71xx: fix Arduino Yun enabling of level shifters outputs
As show in Arduino Yun schematic [1] GPIO 21 and 22 are connected to
output enable pin (OE) of two NTB01xx level shifters.

NTB01xx datasheets [2] [3] states that OE pin are active-high
therefore we should initialize GPIO 21 (DS_GPIO_OE) and GPIO 22
(DS_GPIO_OE2) accordingly to actually enable level shifters outputs.

[1] https://www.arduino.cc/en/uploads/Main/arduino-Yun-schematic.pdf
[2] https://www.nxp.com/docs/en/data-sheet/NTB0102.pdf
[3] https://www.nxp.com/docs/en/data-sheet/NTB0104.pdf

Signed-off-by: Edoardo Scaglia <edoardo.87@gmail.com>
2019-02-08 17:27:47 +01:00
Koen Vandeputte
206bebcad4 kernel: bump 4.14 to 4.14.97
Refreshed all patches.

Adapted patches:
- 012-kbuild-add-macro-for-controlling-warnings-to-linux-c.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-01 11:41:00 +01:00
Jo-Philipp Wich
19850b639e ar71xx: fix packed-not-aligned error with GCC 8.
Building ar71xx currently fails with:

    In file included from ./include/linux/ipv6.h:5,
                     from ./include/net/ipv6.h:16,
                     from ./include/net/inetpeer.h:16,
                     from ./include/net/ip_fib.h:24,
                     from ./include/net/switchdev.h:17,
                     from ./include/net/dsa.h:23,
                     from arch/mips/ath79/dev-dsa.h:15,
                     from arch/mips/ath79/dev-dsa.c:17:
    ./include/uapi/linux/ipv6.h:107:1: error: alignment 1 of 'struct ipv6_destopt_hao' is less than 2 [-Werror=packed-not-aligned]
     } __attribute__((packed));

Address this issue by correcting the alignment of the struct packing
pragma accordingly.

Fixes: FS#1805
Reported-by: Pascal Ernster <git@hardfalcon.net>
[reword subject, rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-01-30 12:49:36 +01:00
David Santamaría Rogado
4bcf581352 ar71xx: use correct wan mac address for the TP-Link Archer C7 v4
The correct MAC address for this device is lan_mac +1, there is no
need to set lan_mac so use base_mac variable instead lan_mac.

Based on this PR for ath79:
https://github.com/openwrt/openwrt/pull/1726

Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
[fix alphabetical ordering, reword subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-01-30 12:24:07 +01:00
Koen Vandeputte
3662157d8b kernel: bump 4.14 to 4.14.96
Refreshed all patches.

Remove upstreamed patches:
- 142-jffs2-Fix-use-of-uninitialized-delayed_work-lockdep-.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-28 18:17:32 +01:00
Koen Vandeputte
528508ae8b kernel: bump 4.14 to 4.14.95
Refreshed all patches.

Removed superseded patches:
- 0400-Revert-MIPS-smp-mt-Use-CPU-interrupt-controller-IPI-.patch

Compile-tested on: ar71xx, cns3xxx, imx6, lantiq (xrx200, AVM 3370), x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, lantiq (xrx200, AVM 3370)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Mathias Kresin <dev@kresin.me>
Tested-by: Robert Resch <openwrt@webnmail.de>
2019-01-24 10:10:45 +01:00
Milan Krstic
39ede7bc67 ar71xx: ag71xx: preserve port mirror flags during swconfig apply
The swconfig load operation always triggers 'apply' function which in
this driver currently clears port mirroring flags effectively undoing
port mirroring configuration.

This fix preserves port mirroring flags during apply.

Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
2019-01-22 09:05:59 +01:00
Mathias Kresin
fd35c5b205 build: move seama commands to image-commands.mk
Move it to image-commands.mk to get rid of duplicate recipes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:13 +01:00
Mathias Kresin
de42466528 ar71xx: sync seama image build code with ramips
Use the same syntax as used in the ramips target, to use common seama
recipes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:13 +01:00
Daniel F. Dickinson
99c81eab78 ar71xx: Fix PowerCloud CR5000 5GHz wifi mac
Without this patch PowerCloud CR5000 AR9382 PCIe 5GHz Wifi uses
the mac address from eeprom instead the one specified when
initializing the PCIe chip.  There were two issues:

1) ap94_pci_init on the second PCIe wmac is wrong as there is only one
PCIe wmac on this device (the other wmac is the AR1022/AR9342 SoC wmac).
2) Without specifying pdata->use_eeprom there is a failure to load
firmware and caldata.

Thanks to Christian Lamparter (@chunkeey) for the heavy lifting and
help. [0]

[0] <https://github.com/openwrt/openwrt/pull/1613>

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-12-20 18:28:59 +01:00
Mathias Kresin
ffdce856e0 build: move append-string to image-commands.mk
Move it to image-commands.mk so that it can used by other targets.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-17 23:21:26 +01:00
Christian Lamparter
f54ac91ef5 ar71xx/ath79: switch devices to the -ct driver and firmware
Since commit 61b5b4971e ("mac80211: make ath10k-ct the default ath10k")
select ath10k-ct and the -ct firmwares by default.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 14:22:28 +01:00
Petr Štetiar
22f9afa118 ar71xx: ag71xx: Replace duplicate debugging code with simple function call
ag71xx_dump_regs is used in code several times, and is providing same
output.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:03:45 +01:00
Romain MARIADASSOU
02494fa35c
Add support for TL-WA801ND v4
This add support for TP-Link TL-WA801ND v4 (same as TL-WA801ND v3) :

Specification:

- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: 650 MHz
- Flash-Chip: Winbond W25Q32BVSIG
- Flash size: 4096 KiB
- RAM: 32 MiB
- Wireless No1: SoC-integrated: QCA9533 2.4GHz 802.11bgn

Flash instructions:

1) To flash the image, rename the file
   openwrt-ar71xx-generic-tl-wa801nd-v4-squashfs-factory.bin
   to firmware.bin
2) Connect your device to the LAN port, then upload the firmware
   through web interface. It will try to download the image and
   flash it.

It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
2018-12-07 21:46:45 +01:00
Daniel Halmschlager
99e212171a ar71xx: Add usb drivers in Archer C7 v4/v5 images
This commit adds the default usb packages
- kmod-usb-core
- kmod-usb2
- kmod-usb-ledtrig-usbport
for Archer C7 v4 and v5.
(The C7 v5 configuration is based on the v4, therefore the change for v4
also applies for v5.)

Signed-off-by: Daniel Halmschlager <dh@dev.halms.at>
2018-12-05 21:30:37 +00:00
INAGAKI Hiroshi
879f2ef7c0 ath79: modify mtd partitions for Buffalo BHR-4GRV2
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.

In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.

0x50000                       0xe80000        0xff0000
  +-------------------------------+--------------+
  |            rootfs             |    kernel    |
  |           (14528k)            |    (1472k)   |
  +-------------------------------+--------------+

After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.

0x50000                                       0xff0000
  +----------------------------------------------+
  |                   firmware                   |
  |                   (16000k)                   |
  +----------------------------------------------+

However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".

This commit requires new flash instruction instead of the old one.

Flash instruction using initramfs image:

1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
  /dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
  fw_setenv ipaddr 192.168.12.1
  fw_setenv serverip 192.168.12.10
  fw_setenv ethaddr 00:aa:bb:cc:dd:ee
  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing

And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-26 12:28:17 +01:00
Sergey Ryazanov
8baad26d01 ar71xx: fix RouterBOARD Power LED default state
RouterBOARD(s) bootloader actully turns Power LED off just before
it starts the kernel. So we need to set the LED default status to On
instead of Keep in order to keep LED on during kernel boot.

This change fixes Power LED off during the kernel boot on the RB91x and
SXT Lite boards.

Fixes: 6cad8ee0bd ("ar71xx: keep the RouterBOARD Power LED in On state")

CC: Mathias Kresin <dev@kresin.me>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-11-26 12:05:45 +01:00
Christoph Krapp
987b961537 ar71xx: add support for UniFi-AC-Mesh-Pro
This adds the build option for UniFi AC Mesh Pro as well as
model detection for it.
The device is a hardware clone of the AC Pro.

- SoC: QCA9563-AL3A (775Mhz)
- RAM: 128MiB
- Flash: 16MiB - dual firmware partitions!
- LAN: 2x 1000M - POE+
- Wireless:
        2.4G: QCA9563
          5G: UniFi Chip, QCA988X compatible

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-11-26 12:05:44 +01:00