Commit Graph

184 Commits

Author SHA1 Message Date
Tobias Schramm
336a531c15 mvebu: add support for SolidRun ClearFog Pro
The SolidRun ClearFog Pro is a router based on the SolidRun CN9130 SOM.

Specs:
 - SoC: Quad-Core Cortex-A72 CN9130 SoC
 - RAM: 4GiB DDR4
 - Serial: Micro-USB port on front (FT232R, 115200 8n1)
 - Storage: 8GiB eMMC, microSD card slot, 8MiB SPI NOR flash
 - Ethernet: 7x GbE (1 port dedicated on SoC, 6 port switch with single GbE CPU port)
 - SFP: 1x SFP+
 - USB: 1x USB-A 3.1 Gen 1
 - PCIe: 2x mini PCIe (one slot with USB and SIM card socket)
 - SATA: 1x M.2 Key-B

In addition to the usual connectivity options this device also features
an internal mikroBUS expansion connector.

SATA is currently untested due to lack of a suitable M.2 SSD.

Installation
============

1. Write sdcard sysupgrade image to microSD card using dd or similar
2. Insert microSD card into router and apply power
3. Device boots into OpenWRT
4. (optional) dd sysupgrade image to /dev/mmcblk0 to install to eMMC

Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
2024-03-02 14:21:20 +01:00
Jan Jasper de Kroon
6f23e92e1c mvebu: add kernel module for Turris Omnia Wi-Fi 6
The following kernel module package was added to the build recipe for the
Turris Omnia: kmod-mt7915-firmware

This module enables support for the official Wi-Fi 6 upgrade kit sold by
CZ.NIC, which includes the AW7915-NP1 miniPCIE board based on Mediatek
MT7915AN, providing 5 GHz Wi-Fi 6 connectivity. With this commit we now
support the latest Turris Omnia Wi-Fi 6 Edition

Signed-off-by: Jan Jasper de Kroon <jajadekroon@gmail.com>
2024-02-26 21:34:27 +01:00
Daniel Golle
6d546b3b4c mvebu: fix RTC of IEI-World Puzzle M90x devices
The Puzzle devices come with an I2C-connected Epson RX8130 RTC.
Disable the (dysfunctional) RTC units of the SoC and add driver
kmod-rtc-ds1307 to support the Epson RX8130 instead.

Tested-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-12-18 22:17:09 +00:00
Daniel Golle
3f7637b050 mvebu: add support for Synology DS213j
The Synology DS213j is a rather dated dual-bay SATA NAS based on on the
Marvell Armada-370 SoC. It has long been supported in vanilla Linux,
however, flash partitioning there didn't match with reality (ie. the
bootloaders expectations) and nobody cared to wrap up OpenWrt support
for the device.

CPU: Marvell Armada-370 ARMv7 SoC @ 1200 MHz
RAM: 512 MB DDR3
Flash: 8 MB (Micron Technology N25Q064)
Network: 1x 1000M/100M/10M Ethernet (Marvell 88E1510)
SATA: 2x 3.0Gbps
USB: 2x USB 2.0

As OS options are becoming limited on that still quite useful hardware,
patch the flash partitions to be able to get the most out of it when
using OpenWrt.

The vendor firmware loads kernel and initrd from fixed addresses in
the flash, not making use of a modifyable environment stored in flash
which is stored at a location right in the middle of the vendor's
zImage partition (at 0x100000).

Stock firmware flash layout:

0x000000 ~ 0x0c0000 : "RedBoot" (actually U-Boot)
0x0c0000 ~ 0x390000 : "zImage"
0x390000 ~ 0x7d0000 : "rd.gz"
0x7d0000 ~ 0x7e0000 : "vendor" (contains MAC address, serial no)
0x7e0000 ~ 0x7f0000 : "RedBoot Config" (unused? legacy left-over)
0x7f0000 ~ 0x800000 : "FIS directory" (unused? legacy left-over)

OpenWrt flash layout:

0x000000 ~ 0x0c0000 : "u-boot"
0x0c0000 ~ 0x100000 : "gap"
0x100000 ~ 0x110000 : "u-boot-env"
0x110000 ~ 0x7d0000 : "kernel"
0x7d0000 ~ 0x7e0000 : "vendor" (contains MAC address, serial no)
0x7e0000 ~ 0x800000 : "gap2"

"kernel", "gap" and "gap2" are concatenated using the mtd-concat
virtual MTD driver, resulting in a partition "firmware" used by
OpenWrt for kernel, rootfs and rootfs-overlay, 0x720000 (7296kiB) in
total.

Installation:
1. Connect to internal serial console port and Ethernet port,
   providing a TFTP server at a static IPv4 address, e.g.
   192.168.1.254/24.
2. Interrupt bootloader using CTRL+C
3. Configure bootloader to load OpenWrt on future boot:
   setenv bootcmd "bootm f4110000"
   saveenv
4. Load and boot initramfs image via TFTP:
   setenv ipaddr 192.168.1.1
   setenv serverip 192.168.1.254
   tftpboot openwrt-mvebu-cortexa9-synology_ds213j-initramfs-kernel.bin
   bootm
5. Use sysupgrade to load final image.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-20 13:24:06 +00:00
INAGAKI Hiroshi
c441f9b2c5 mvebu: add support for IIJ SA-W2
Internet Initiative Japan Inc. (IIJ) SA-W2 is a network appliance with
11ac (Wi-Fi 5) wlan, based on 88F6810.

Specification:

- SoC         : Marvell Armada 380 88F6810
- RAM         : DDR3 256 MiB (Micron MT41K64M16TW-107:J x2)
- Flash       : SPI-NOR 32 MiB (Winbond W25Q256JVFIQ)
- WLAN        : 2.4/5 GHz, Mini PCI-E
  - 2.4 GHz   : Silex SX-PCEGN (Atheros AR9287 (2T2R))
  - 5 GHz     : Silex SX-PCEAC (Qualcomm Atheros QCA9880 (3T3R))
- Ethernet    : 10/100/1000 Mbps x5
  - Switch    : Marvell 88E6172
- LEDs/Keys   : 12x/1x
- UART        : "CONSOLE" port (RJ-45, RS-232C)
  - settings  : 115200n8
  - assignment: 1:NC,  2:NC,  3:TXD, 4:GND,
                5:GND, 6:RXD, 7:NC,  8:NC
  - note      : compatible with Cisco console cable
- Power       : DC Input or PoE
  - DC Input  : 12 VDC, 3 A
  - PoE       : 802.3af
    - module  : Silvertel Ag9712-2BR
    - note    : USB ports shouldn't be used when powered by PoE
- Bootloader  : PMON2000 based
- Stock       : NetBSD based

Flash instruction using sysupgrade image:

1. Prepare TFTP server with IP address 192.168.0.10 and put sysupgrade
   image to TFTP directory
2. Connect PC to "GE0/PoE" port on SA-W2
3. Power on SA-W2, interrupt count-down by Esc and enter to bootloader
   CLI
4. Set IP address of the device

   address 192.168.0.1

5. Download sysupgrade image and flash to storage

   tftpload 192.168.0.10 <image name>
   firmwrite

   example:

   #tftpload 192.168.0.10 openwrt-mvebu-cortexa9-iij_sa-w2-squashfs-sysupgrade.bin
   Loading openwrt-mvebu-cortexa9-iij_sa-w2-squashfs-sysupgrade.bin
   loaded 8127268 byte(s)
   #firmwrite
   Erasing FLASH block  32 Done 0x00200000.
   Erasing FLASH block  33 Done 0x00210000.
   ...
   Erasing FLASH block 155 Done 0x009b0000.
   Erasing FLASH block 156 Done 0x009c0000.
   Programming FLASH. Done.
   Verifying FLASH. No Errors found.

6. Check the flashed firmware

   firmcheck

   example:

   #firmcheck
   [Normal firmware]
   ident: 'SEIL2015'
   copyright: 'ARM OpenWrt Linux-5.15.93'
   version format: 1
   version major: 9
   version minor: 99
   version release: 'r22060+36-5163bb5e54'
   body size: 3578524
   checksum: 0x8a083cb8

   [Rescue firmware]
   ident: 'SEIL2015'
   copyright: 'Copyright (c) 2017 Internet Initiative Japan Inc. All rights reserved.'
   version format: 1
   version major: 3
   version minor: 70
   version release: 'Release'
   body size: 10152458
   checksum: 0x8f9518c2

7. Boot with the flashed firmware

   boot

Note:

- The bootloader on this device is not U-Boot and it's environment space
  ("bootloader-env") has no compatibility with U-Boot tools.

- eth1 is connected to port6 of 88E6172 switch, but multi-cpu port can't
  be handled on Linux Kernel and not defined.

- Powering by PoE hasn't been tested yet.

- This device has 2x OS images on flash and they can be switched by
  setting "BOOTDEV" variable on bootloader CLI.
  That variable supports the following values:

  - "flash" : primary image on flash ("firmware")
  - "rescue": secondary image on flash ("rescue")
  - "usb"   : usb storage (broken?)
  - "lan0/1": network

  command to set:

  set BOOTDEV=<dev>

  example:

    set BOOTDEV=rescue

  This commit also supports booting from secondary partition.

- To execute initramfs image on bootloader CLI, use "go" command.
  ("go" command is not listed on the output of "help", but available)

  example (download and execute):

    address 192.168.0.1
    tftpload 192.168.0.10 openwrt-mvebu-cortexa9-iij_sa-w2-initramfs-kernel.bin
    go

MAC addresses:

LAN    : 00:E0:4D:xx:xx:19 (none)
WAN    : 00:E0:4D:xx:xx:18 (board_info, 0x6 (hex))
2.4 GHz: 84:25:3F:xx:xx:xx (Mini PCI-E card)
5 GHz  : 84:25:3F:xx:xx:xx (Mini PCI-E card)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-10-31 14:02:01 +01:00
INAGAKI Hiroshi
b7c12a9bfc mvebu: add support for Fortinet FortiGate 30E
Fortinet FortiGate 30E (FG-30E) is a UTM, based on Armada 385 (88F6820).

Specification:

- SoC          : Marvell Armada 385 88F6820
- RAM          : DDR3 1 GiB (4x Micron MT41K256M8DA-125, "D9PSH")
- Flash        : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet     : 5x 10/100/1000 Mbps
  - Switch     : Marvell 88E6176
- LEDs/Keys    : 16x/1x
- UART         : "CONSOLE" port (RJ-45, RS-232C level)
  - port       : ttyS0
  - settings   : 9600bps 8n1
  - assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
                5:GND, 6:RXD, 7:NC , 8:NC
  - note       : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power        : 12 VDC, 2 A
  - plug       : Modex 5557-02R

Flash instruction using initramfs image:

 1. Power on FG-30E and interrupt to show bootmenu
 2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
    and set baudrate to 9600 bps
 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
    connect computer to "Image download port" in the parameters
 4. Prepare TFTP server with the parameters obtained above
 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
    directory
 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
    image from TFTP server
 7. Type "r" key when the following message is showed, to boot initramfs
    image without flashing to spi-nor flash

    "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"

 8. On initramfs image, backup mtd if needed

    minimum:

    - "firmware-info"
    - "kernel"
    - "rootfs"

 9. On initramfs image, upload sysupgrade image to the device and perform
    sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
    If the device is booted with stock firmware, login to bootmenu and
    call "[B]: Boot with backup firmware and set as default." to set the
    first OS image as default and boot it.

Notes:

- Both colors of Bi-color LEDs on the front panel cannot be turned on at
  the same time.

- "PWR" and "Logo" LEDs are connected to power source directly.

- The following partitions are added for OpenWrt.
  These partitions are contained in "uboot" partition (0x0-0x1fffff) on
  stock firmware.

  - "firmware-info"
  - "dtb"
  - "u-boot-env"
  - "board-info"

Image header for bootmenu tftp:

  0x0 - 0xf  : ?
 0x10 - 0x2f : Image Name
 0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?

*: required for initramfs image

MAC addresses:

(eth0): 70:4C:A5:xx:xx:CE (board-info, 0xd880 (hex))
WAN   : 70:4C:A5:xx:xx:CF
LAN 1 : 70:4C:A5:xx:xx:D0
LAN 2 : 70:4C:A5:xx:xx:D1
LAN 3 : 70:4C:A5:xx:xx:D2
LAN 4 : 70:4C:A5:xx:xx:D3

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-10-29 02:12:38 +02:00
Klaus Kudielka
75a3760862 mvebu: stop building omnia-medkit
Since August 2022, users of very old Turris Omnias have been
encouraged to update U-Boot before OpenWrt installation [1].
The omnia-medkit (only useful for installation with
U-Boot 2015.10-rc2) is not needed anymore.

[1] https://openwrt.org/toh/turris/turris_omnia#installation

Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
2023-06-01 23:54:20 +02:00
INAGAKI Hiroshi
102dc5a625 mvebu: add support for Fortinet FortiGate 50E
Fortinet FortiGate 50E (FG-50E) is a UTM, based on Armada 385 (88F6820).

Specification:

- SoC          : Marvell Armada 385 88F6820
- RAM          : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash        : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet     : 7x 10/100/1000 Mbps
  - LAN 1-5    : Marvell 88E6176
  - WAN 1, 2   : Marvell 88E1512 (2x)
- LEDs/Keys    : 18x/1x
- UART         : "CONSOLE" port (RJ-45, RS-232C level)
  - port       : ttyS0
  - settings   : 9600bps 8n1
  - assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
                 5:GND, 6:RXD, 7:NC , 8:NC
  - note       : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power        : 12 VDC, 2 A
  - plug       : Molex 5557-02R

Flash instruction using initramfs image:

1. Power on FG-50E and interrupt to show bootmenu
2. Call "[R]: Review TFTP parameters.", check TFTP parameters and
   connect computer to "Image download port" in the parameters
3. Prepare TFTP server with the parameters obtained above
4. Rename OpenWrt initramfs image to "image.out" and put to TFTP
   directory
5. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
   image from TFTP server
6. Type "r" key when the following message is showed, to boot initramfs
   image without flashing to spi-nor flash

   "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"

7. On initramfs image, backup mtd if needed

   minimum:

   - "firmware-info"
   - "kernel"
   - "rootfs"

7. On initramfs image, upload sysupgrade image to the device and perform
   sysupgrade
8. Wait ~200 seconds to complete flashing and rebooting.
   If the device is booted with stock firmware, login to bootmenu and
   call "[B]: Boot with backup firmware and set as default." to set the
   first OS image as default and boot it.

Notes:

- All "SPEED" LEDs(Green/Amber) of LAN and 1000M "SPEED" LEDs(Green) of
  WAN1/2 are connected to GPIO expander. There is no way to indicate
  link speed of networking device on Linux Kernel/OpenWrt, so those LEDs
  cannot be handled like stock firmware.
  On OpenWrt, use netdev(link) trigger instead.

- Both colors of Bi-color LEDs on the front panel cannot be turned on at
  the same time.

- "PWR" and "Logo" LEDs are connected to power source directly.

- The following partitions are added for OpenWrt.
  These partitions are contained in "uboot" partition (0x0-0x1fffff) on
  stock firmware.

  - "firmware-info"
  - "dtb"
  - "u-boot-env"
  - "board-info"

Image header for bootmenu tftp:

  0x0 - 0xf  : ?
 0x10 - 0x2f : Image Name
 0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?

*: required for initramfs image

MAC addresses:

(eth0): 70:4C:A5:xx:xx:7C (board-info, 0xd880 (hex))
WAN 1 : 70:4C:A5:xx:xx:7D
WAN 2 : 70:4C:A5:xx:xx:7E
LAN 1 : 70:4C:A5:xx:xx:7F
LAN 2 : 70:4C:A5:xx:xx:80
LAN 3 : 70:4C:A5:xx:xx:81
LAN 4 : 70:4C:A5:xx:xx:82
LAN 5 : 70:4C:A5:xx:xx:83

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-03-08 23:49:39 +01:00
Daniel González Cabanelas
be0f1c1b26 mvebu: add support for Buffalo LinkStation LS220DE
The Buffalo LinkStation LS220DE is a dual bay NAS, based on Marvell
Armada 370

Hardware:
   SoC:         Marvell Armada 88F6707
   CPU:         Cortex-A9 800 MHz, 1 core
   Flash 1:     SPI-NOR 1 MiB (U-Boot)
   Flash 2:     NAND 512 MiB (OS)
   RAM:         DDR3 256 MiB
   Ethernet:    1x 1GbE
   USB:         1x 2.0
   SATA:        2x 3Gb/s
   LEDs/Input:  5x / 2x (1x button, 1x slide-switch)
   Fan:         1x casing

Flash instructions, from hard drive:
  1. Get access to the "boot" partition at the hard drive where the stock
     firmware is installed. It can be done with acp-commander or by
     plugging the hard drive to a computer.
  2. Backup the stock uImage:
         mv /boot/uImage.buffalo /boot/uImage.buffalo.bak
  3. Move and rename the Openwrt initramfs image to the boot partition:
         mv openwrt-initramfs-kernel.bin /boot/uImage.buffalo
  4. Power on the Linkstation with the hardrive inside. Now Openwrt will
     boot, but still not installed.
  5. Connect via ssh to OpenWrt:
         ssh root@192.168.1.1
  6. Rename boot files inside boot partition
         mount -t ext3 /dev/sda1 /mnt
         mv /mnt/uImage.buffalo /mnt/uImage.buffalo.openwrt.bak
         mv /mnt/initrd.buffalo /mnt/initrd.buffalo.bak
  7. Format ubi partitions at the NAND flash ("kernel_ubi" and "ubi"):
         ubiformat /dev/mtd0 -y
         ubidetach -p /dev/mtd1
         ubiformat /dev/mtd1 -y
  8. Flash the sysupgrade image:
         sysupgrade -n openwrt-squashfs-sysupgrade.bin
  9. Wait until it finish, the device will reboot with OpenWrt installed
     on the NAND flash.

Restore the stock firmware:
  1. Take the hard drive used for the installation and restore boot backup
     files to their original names:
         mount -t ext3 /dev/sda1 /mnt
         mv /mnt/uImage.buffalo.bak /mnt/uImage.buffalo
         mv /mnt/initrd.buffalo.bak /mnt/initrd.buffalo
  2. Boot from the hard drive and perform a stock firmware update using
     the Buffalo utility. The NAND will be restored to the original
     state.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-02-26 22:22:48 +01:00
Rosen Penev
2630e5063d treewide: replace wpad-basic-wolfssl default
The newly merged mbedtls backend is smaller and has fewer ABI related
issues than the wolfSSL one.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-02-04 02:35:03 +01:00
Josef Schlehofer
6475d030b9 mvebu: cortexa9: use renamed U-boot binaries
Due to upstream change in U-boot the binaries were renamed [1].

[1] 87ac4b4b4c

Fixes: 2f83369e3e ("uboot-mvebu: update to version 2023.01")
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2023-01-20 21:10:37 +01:00
Daniel Golle
1d3b57dbee
mvebu: cortexa72: fix ImageBuilder for IEI Puzzle devices
The line trying to generate the standard sdcard.img.gz fails due to
boot.scr not being generated.
Remove the line in order to use the default sdcard.img.gz which is
exactly the same but includes generating the boot.scr file.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-07-04 18:36:09 +01:00
Robert Marko
57a38c8d3e mvebu: add Methode euroDPU support
Add support for Methode euroDPU which is based on uDPU but does not
have a second SFP cage, instead of which a Maxlinear G.hn IC is used.

PHY mode is set to 1000Base-X despite Maxlinear IC being capable of
2500Base-X since until 5.15 support for mvebu is available trying to use
2500Base-X will cause buffer overruns for which the fix is not easily
backportable.

Installation instructions:
1. Boot the FIT initramfs image (openwrt-mvebu-cortexa53-methode_edpu-initramfs.itb)
2. sysupgrade using the openwrt-mvebu-cortexa53-methode_edpu-firmware.tgz

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-06-29 13:08:59 +02:00
Stefan Kalscheuer
f8fa38c13f kernel: add kmod-leds-turris-omnia
Add support for LEDs of the CZ.NIC Turris Omnia using the upstream
driver.

There is no generic way to control the LEDs in UCI manner, however
the kernel module is the first step to actually use the RGB LEDs in
custom logic.

Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
(removed DMARC notice, added driver to Turris Omnia, moved module
recipe to target/linux/mvebu/modules.mk)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-24 09:18:03 +02:00
Logan Blyth
36e46c3c13 mvebu: add SolidRun ClearFog GT 8K
ClearFog GT 8K is device sold by SolidRun. It is marketed as a
development board, not a consumer product. The device tree file for this board
is upstream in kernel.org.

Signed-off-by: Logan Blyth <mrbojangles3@gmail.com>
2022-06-19 12:40:30 +02:00
Daniel Golle
44b457168e
mvebu: make boot filesystem reproducible
Set timestamp option for make_ext4fs to make boot filesystem
reproducible.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-03-28 20:52:49 +01:00
Robert Marko
a8b2d35903 mvebu: udpu: include LM75 kmod by default
uDPU has 2 LM75 compatible temperature sensors, so include the driver for
them by default in order to utilize them.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-03-21 14:00:34 +01:00
Robert Marko
80f21e5336 mvebu: udpu: fix initramfs booting
uDPU provides a FIT based initramfs, but currently gets stuck after U-boot
starts the kernel at "Starting kernel..".

It is due to the load address being too low, so increase it in order to get
the initramfs booting again.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-03-21 14:00:34 +01:00
Sungbo Eo
6ff970bb51 mvebu: add support for ipTIME NAS1dual
ipTIME NAS1dual is a 1-bay NAS, based on Marvell Armada 385 SoC.

Specifications:
* SoC: 88F6820
* RAM: 2 GiB
* Flash: SPI NOR 64 MiB
* SATA: 1x 3Gb/s
* Ethernet: 2x 1GbE
* USB: 1x 3.0
* Fan: 2 speed level
* UART: J11 (115200 8N1)
  * Pinout: [3V3] (TXD) (RXD) (GND)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Pawel Dembicki
9149ed4f05 mvebu: cortexa9: Add support for Ctera C200-V2
2-Bay NAS - maximum two 3.5" Harddisks

Hardware:
  - SoC: Marvell 88F6707-A1 ARMv7 Processor 1,2GHz (ARMADA 370 SoC)
  - Ram: 1GB (2x Nanya NT5CC512M8DN-D1)
  - NAND Flash: 256MB (ESMT F59L2G81A-25T)
  - Lan: 1x GBE (Marvell 88E1318-NNB2)
  - Storage: 2x SATA HDD 3.5" Slot
  - USB: 2x USB 3.0 port (Renesas uPD720202)
  - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
  - LEDs: 13x GPIO controlled
  - Buttons: 2x GPIO controlled

Known issues:
  - Buzzer is unused due lack of proper driver
  - USB1/2 usbport ledtrigger won't work (through DT)
  - Renesas uPD720202 requires firmware file. It's possible to find
    non-free binary. Please look for 'UPDATE.mem' file and put in into
    '/lib/firmware/renesas_usb_fw.mem' file.

Installation:
  - Apply factory initramfs image via stock web-gui.
  - Do sysupgrade to make installation complete.

Back to stock:
  - OpenWrt rootfs partition use unused space after stock firmware.
  - Full revert is possible.
  - Login via ssh and run:

 ## ctera_c200-v2_back_to_factory start ##
 . /lib/functions.sh
 part=$(find_mtd_part "active_bank")
 active_bank=$(strings "$part" | grep bank)
 if [ "$active_bank" = "bank1" ]; then
 	echo "bank2" > /tmp/change_bank
 else
 	echo "bank1" > /tmp/change_bank
 fi
 mtd write /tmp/change_bank active_bank
 reboot
 ## ctera_c200-v2_back_to_factory end ##

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(put back-to-stock script into commit message, removed dup. SUBPAGESIZE var,
added 01_leds for non-working dt-usb-port trigger)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:41:19 +01:00
Robert Marko
78cf3e53b1 mvebu: add Globalscale MOCHAbin
Globalscale MOCHAbin is a Armada 7040 based development board.

Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element

Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.

Installation:

Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/
$ in.tftpd -L -s bin/targets/mvebu/cortexa72/

Connect to the device UART via microUSB port and power on the device.

Power on the device and hit any key to stop the autoboot.

Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device

Set the ethernet device (Example for the 1G WAN):
$ setenv ethact mvpp2-2

Ping server to confirm network is working:
$ ping $serverip
Using mvpp2-2 device
host 192.168.1.15 is alive

Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin
$ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb

Boot the image:
$ booti $kernel_addr_r - $fdt_addr_r

Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
to /tmp dir on the device.

Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync

Reboot the device.

Hit any key to stop the autoboot.

Reset U-boot env and set the bootcmd:
$ env default -a
$ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}'

Optionally I would advise to edit the console env variable to remove earlycon as that
causes the kernel to never use the driver for the serial console.
Earlycon should be used only for debugging before the kernel can configure the console
and will otherwise cause various issues with the console.

$ setenv console 'console=ttyS0,115200'

Save and reset
$ saveenv
$ reset

OpenWrt should boot from eMMC now.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-10-02 16:45:35 +02:00
Ian Chang
70c75965a9 mvebu: add support for iEi Puzzle-M901/Puzzle-M902
Hardware specification
 ----------------------
 * CN9130 SoC, Quad-core ARMv8 Cortex-72 @ 2200 MHz
 * 4 GB DDR
 * 4 GB eMMC
 * mmcblk0
 - mmcblk0p1    64M  kernel_1
 - mmcblk0p2    64M  kernel_2
 - mmcblk0p3   512M  rootfs_1
 - mmcblk0p4   512M  rootfs_2
 - mmcblk0p5   512M  Reserved
 - mmcblk0p6    64M  Reserved
 - mmcblk0p7   1.8G  rootfs_data

 * 4 MB (SPI Flash)
 * 6 x 2.5 Gigabit  ports (Puzzle-M901)
 - External PHY with 6 ports (AQR112R)

 * 6 x 2.5 Gigabit ports (Puzzle-M902)
 - External PHY with 6 ports (AQR112R)
   3 x 10 Gigabit ports (Puzzle-M902)
 - External PHY with 3 ports (AQR113R)

 * 4 x Front panel LED
 * 1 x USB 3.0
 * Reset button on Rear panel
 * UART (115200 8N1,header on PCB)

 Flash instructions:
    The original firmware is based on OpenWrt.
    Flash firmware using LuCI and CLI

Signed-off-by: Ian Chang <ianchang@ieiworld.com>
2021-09-09 23:36:13 +02:00
Klaus Kudielka
82620cd610 mvebu: Turris Omnia: use SFP module, if present
Follow the recommendations stated in the Turris Omnia DTS for eth2:

"In case SFP module is present, U-Boot has to enable the sfp node above,
remove phy-handle property, and add managed = "in-band-status" property."

The boot script is written in a way, that it works for all U-Boot
versions deployed by the vendor so far (2015.10-rc2, 2019.07).

Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
2021-08-08 19:50:45 +02:00
Tad Davanzo
b4f76d9f0d mvebu: enable WRT1900AC v1 and WRT32X for buildbots
Kernel size limits have been dealt with.
Effective revert of a1eb2c46 and ac9730c4.

Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-03-19 15:30:01 +01:00
Tad Davanzo
15309f5133 mvebu: venom resize kernel to 6MB
venom has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.

venom uboot however as set from factory will load up to 6MB.
This can be observed by looking a uboot log:
	NAND read: device 0 offset 0x900000, size 0x600000
	6291456 bytes read: OK
and from uboot environment variables:
	$ fw_printenv | grep "priKernSize";
	priKernSize=0x0600000

Resize the root partitions from 120MB to 117MB to let kernel expand
into it another 3MB.
And set kernel target size to 6MB.

Lastly set the kernel-size-migration compatibility version on venom to
prevent sysupgrading without first reinstalling from a factory image.

Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-03-19 15:30:01 +01:00
Tad Davanzo
10415d5e70 mvebu: mamba resize kernel to 4MB
mamba has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.

mamba uboot however as set from factory will load up to 4MB.
This can be observed by looking a uboot log:
	NAND read: device 0 offset 0xa00000, size 0x400000
	4194304 bytes read: OK
and from uboot environment variables:
	$ fw_printenv | grep "pri_kern_size";
	pri_kern_size=0x400000

Resize the root partitions from 37MB to 36MB to let kernel expand
into it another 1MB.
And set kernel target size to 4MB.

Lastly add a compatibility version message: kernel-size-migration.
And set it on mamba to prevent sysupgrading without first reinstalling from
a factory image.

Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-03-19 15:30:01 +01:00
Adrian Schmutzler
ef2cb8572b treewide: rename IMAGE_PREFIX/IMAGE_NAME to DEVICE_IMG_*
We so far had two variables IMG_PREFIX and IMAGE_PREFIX with
different content. Since these names are obviously quite
confusing, this patch renames the latter to DEVICE_IMG_PREFIX,
as it's a device-dependent variable, while IMG_PREFIX is only
(sub)target-dependent.

For consistency, also rename IMAGE_NAME to DEVICE_IMG_NAME, as
that's a device-dependent variable as well.

Cc: Paul Spooren <mail@aparcar.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-25 18:11:06 +01:00
Adrian Schmutzler
7157c77c6d target: use SPDX license identifiers on scripts
Use SPDX license tags to allow machines to check licenses.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 15:47:23 +01:00
Adrian Schmutzler
598b29585e target: use SPDX license identifiers on Makefiles
Use SPDX license tags to allow machines to check licenses.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 15:47:18 +01:00
Petr Štetiar
337ff74894 mvebu: omnia: make initramfs image usable out of the box
Currently it's not possible to boot the device with just initramfs image
without additional effort as the initramfs image doesn't contain device
tree.  Fix it by producing FIT based image which could be booted with
following commands:

 setenv bootargs earlyprintk console=ttyS0,115200
 tftpboot ${kernel_addr_r} openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
 bootm ${kernel_addr_r}

Acked-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-01-31 11:39:19 +01:00
Adrian Schmutzler
f52081bcf9 treewide: provide global default for SUPPORTED_DEVICES
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:

  SUPPORTED_DEVICES := $(subst _,$(comma),$(1))

At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:

  device/image name:  vendor_model
  compatible:         vendor,model

The equal redundant definitions are a symptom of this process.

Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.

This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-23 12:45:21 +01:00
Sungbo Eo
583e39e3d5 kernel: drop empty kmod-ledtrig-* packages
The following four led triggers are enabled in generic config.

* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer

Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-01-15 18:24:31 +01:00
Petr Štetiar
3aeaef6e56 Revert "mvebu: fix initramfs/kernel image for CZNIC Turris Omnia"
This reverts commit e401a2a42e as at least
two users had reported breakage on their devices.

References: https://lists.infradead.org/pipermail/openwrt-devel/2020-December/032837.html
References: e401a2a42e (commitcomment-45189788)
Cc: Karel Kočí <karel.koci@nic.cz>
Reported-by: Magnus Kroken <mkroken@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-12-22 19:11:37 +01:00
Tomasz Maciej Nowak
85caf21ade mvebu: macchiatobin-singleshot: enable heartbeat LED
With board revision 1.3, SolidRun moved the power LED to the middle of
the board. In old place of power LED a GPIO controllable heartbeat LED
was added. This commit touches only Single Shot variant, because all
have revision 1.3. Some boards could be placed in an enclosure, therefore
the LED18 is enabled by default, since that'll be the only visible
indicator that the board is operating.

Ref: http://wiki.macchiatobin.net/tiki-index.php?page=Schematics#Revision1.3_Electrical_Design_Changes
Ref: http://macchiatobin.net/wp-content/uploads/2017/11/MACCHIATOBin-rev-1_3.pdf

Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2020-12-20 00:00:33 +01:00
Karel Kočí
e401a2a42e mvebu: fix initramfs/kernel image for CZNIC Turris Omnia
This adds DTB to kernel and that way makes it possible to easily boot
initramfs image and also kernel.

The sequence to boot initramfs on Omnia is then just:
  env set bootargs earlyprintk console=ttyS0,115200
  dhcp 0x1000000 192.168.1.1:openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
  bootz 0x1000000

Without this change kernel boot won't proceed and is stuck on "Starting
kernel".

Signed-off-by: Karel Kočí <karel.koci@nic.cz>
[fixed From: to match with SoB:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-12-11 13:56:29 +01:00
Klaus Kudielka
afd4375a33 mvebu: Add turris-omnia.bootscript
In contrast to the U-Boot version shipped with older versions of Turris
Omnia (CZ11NIC13, CZ11NIC20), the version shipped with Turris Omnia 2019
(CZ11NIC23) relies on the existence of /boot.scr.

Consequently, add a suitable boot script to the sysupgrade image.

Flash instructions for Turris Omnia 2019:
- Download openwrt-...-sysupgrade.img.gz, gunzip it, and copy the resulting
  .img file to the root of a USB flash drive (FAT32 or ext2/3/4).
- Enter a rescue shell: Either via 5-LED reset and ssh root@192.168.1.1
  on LAN port 4, or via 7-LED reset and the serial console.
- Insert the USB drive and mount it:
  mkdir /mnt; mount /dev/sda1 /mnt
- Flash the OpenWrt image to eMMC:
  dd if=/mnt/openwrt-...-sysupgrade.img of=/dev/mmcblk0 bs=4096 conv=fsync
- Reboot.

Flash instructions using a temporary "medkit" installation were written for
the older versions of Turris Omnia, and will *not* work on the Turris Omnia
2019.

Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
2020-11-26 21:52:04 -10:00
Vladimir Vid
c0af4a0ca2 mvebu: add initial support for Globalscale ESPRESSObin-Ultra
This patch adds support for Globalscale ESPRESSObin-Ultra. Device uses
the same Armada-3720 SoC with extended hardware support.

- SoC: Armada-3720
- RAM: 1 GB DDR4
- Flash: 4MB SPI NOR (mx25u3235f) + 8 GB eMMC
- Ethernet: Topaz 6341 88e6341 (4x GB LAN + 1x WAN with 30W PoE)
- WiFI: 2x2 802.11ac Wi-Fi marvell (88w8997 PCIe+USB)
- 1x USB 2.0 port
- 1x USB 3.0 port
- 1x microSD slot
- 1x mini-PCIe slot (USB [with nano-sim slot])
- 1x mini-USB debug UART
- 1x RTC Clock and battery
- 1x reset button
- 1x power button
- 4x LED (RGBY)
- Optional 1x M.2 2280 slot

** Installation **

Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a53_musl/linux-mvebu_cortexa53/
linux-5.4.65/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dtb
bin/targets/mvebu/cortexa53/
$ in.tftpd -L -s bin/targets/mvebu/cortexa53/

Connect to the device UART via microUSB port on the back side and power on the device.

Power on the device and hit any key to stop the autoboot.

Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device

Ping server to confirm network is working:
$ ping $serverip
Using neta@30000 device
host 192.168.1.15 is alive

Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin
$ tftpboot $fdt_addr_r armada-3720-espressobin-ultra.dtb

Set the console and boot the image:
$ setenv bootargs $console
$ booti $kernel_addr_r - $fdt_addr_r

Once the initramfs is booted, transfer openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
to /tmp dir on the device.

Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img of=/dev/mmcblk0 && sync

Reboot the device.

Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
2020-11-23 22:53:15 +01:00
Andre Heider
c43b45863e mvebu: Add bootscript for espressobin to support mainline firmware
The generic bootscript is tailored around a downstream firmware and
doesn't work on a firmware built from mainline components.

Add a bootscript which:
* sets $console since mainline u-boot doesn't do that
* uses distro boot variables, so OpenWRT can be booted off any supported
  device when using a mainline firmware
* sets missing distro boot variables for the downstream firmware

Booting with a downstream firmware is unchanged.
Booting with a mainline firmware now works.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-10-11 16:53:20 +02:00
Vladimir Vid
9f0d882680 mvebu: image: add check for fdt_add_r and kernel_addr_r variables
fdt_addr and kernel_addr variables are getting obsolete in the mainline
u-boot in favor of fdt_addr_r and kernel_addr_r.

By checking if the new variables exist, we can make sure that devices with newer
version of u-boot will work while not breaking support for the existing ones.

Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-09-17 21:09:51 +02:00
Adrian Schmutzler
de4e57eaaa Revert "treewide: add sysupgrade comment for early DSA-adopters"
This reverts commit e81e625ca3.

This was meant just for early DSA-adopters. Those should have
updated by now, remove it so future updaters get the intended
experience.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-08 19:26:22 +02:00
Daniel González Cabanelas
42d14ace3e mvebu: LS421DE: add linkstation poweroff driver
Compile the Linkstation poweroff module for the Buffalo LS421DE.
Without this driver the device remains forever halted if a power off
command is executed.

The driver will also allow to use the WoL feature, which wasn't availabe
in the stock firmware.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-08-28 10:44:29 +01:00
Petr Štetiar
a14f5bb4bd treewide: use wpad-basic-wolfssl as default
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.

Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-20 14:19:39 +02:00
Adrian Schmutzler
e81e625ca3 treewide: add sysupgrade comment for early DSA-adopters
Add a specific comment for early DSA-adopters that they can keep
their config when prompted due to compat-version increase.

This is a temporary solution, the patch should be simply reverted
before any release.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 20:56:12 +02:00
Adrian Schmutzler
e496eefccc mvebu: increase compat version for SolidRun ClearFog Base
When changing the Pro variant to DSA, the ethernet interface rename
script was dropped by all devices to keep them in sync:

  be309bfd74 ("mvebu: drop 06_set_iface_mac preinit script")

Therefore, network config will be broken after upgrade for the
Base variant as well. Increase the compat version and provide a
message to signal that to the users.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
494f12c52d mvebu: implement compatibility version for DSA migration
This implements the newly introduced compat-version to prevent
upgrade between swconfig and DSA for mvebu.

Just define a compat version with minor increment and an appropriate
message for both image (in Makefile) and device (in base-files).

Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES
that have been removed in previous patches to prevent broken config.

Attention:

All users that already updated to the DSA versions in master will
receive the same incompatibility warning since their devices are still
"1.0" as far as fwtool can tell.
Those, and only those, can bypass the upgrade check by using force (-F)
without having to reset config again. In addition, the new version
string needs to be put into uci config manually, so the new fwtool
knows that it actually deals with a "1.1":

   uci set "system.@system[-1].compat_version=1.1"
   uci commit system

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
a1eb2c4633 mvebu: only disable WRT1900AC v1 and WRT32X for buildbots
Use "DEFAULT := n" to only disable devices for buildbots, but
keep them available for manual build.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 11:05:25 +02:00
Jo-Philipp Wich
ac9730c495 mvebu: disable WRT1900AC v1 and WRT32X images for now
The kernel appears to have grown too large, breaking the build for the
entire target.

Disable the affected images for now until the situation is dealt with.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-07-26 18:58:22 +02:00
Alberto Bursi
480003e9eb mvebu: add Kobol Helios 4 device
The Helios 4 is a NAS from Kobol
that is powered by an Armada 38x
MicroSOM from Solidrun, similarly
to Clearfog.

This device has:
-Armada 38x CPU
 (dual core ARMv7 1.6 Ghz)
-2 GB of ECC RAM
-Gigabit ethernet (Marvell)
-2x USB 3.0 ports
-4x Sata 3.0 ports
-i2c header (J9 |>GND|SDA|SCL|VCC)
-2x 3-pin fan headers with PWM
-micro-usb port is a TTL/UART to
 USB converter connected to TTL
-MicroSD card slot
-System, 4xSata and 1xUSB LEDs

NOT WORKING: fan control

Fan Control requires a kernel patch
that is available in the Armbian
project (the "default firmware"
of this device) and named
mvebu-gpio-remove-hardcoded
-timer-assignment
This patch isn't acceptable
by OpenWrt, it should be upstreamed.
I also have that patch in my own
local OpenWrt builds,
in case you want a more
clean and less confusing patch
for upstreaming.

To install, write the disk image
on a micro SD card with dd or
win32 disk imager, insert the
card in the slot.
Check that the dip switch battery
for boot selection is as follows
Switch 1 and 2 down/off, switches
3, 4, 5 up/on.

Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2020-07-17 11:00:33 +02:00
Tomasz Maciej Nowak
2dc5ce622a mvebu: add support for MACCHIATObin Single Shot
Add support for Marvell MACCHIATObin Single Shot, cortex-a72 based
Marvell ARMADA 8040 Community board. Single Shot was broken as the
device tree is different on the Double Shot Board.

Specifications:
- Quad core Cortex-A72 (up to 2GHz)
- DDR4 DIMM slot with optional ECC and single/dual chip select support
- Dual 10GbE (1/2.5/10GbE) SFP+
  2.5GbE (1/2.5GbE) via SFP
  1GbE via copper
- SPI Flash
- 3 X SATA 3.0 connectors
- MicroSD connector
- eMMC
- PCI x4 3.0 slot
- USB 2.0 Headers (Internal)
- USB 3.0 connector
- Console port (UART) over microUSB connector
- 20-pin Connector for CPU JTAG debugger
- 2 X UART Headers
- 12V input via DC Jack
- ATX type power connector
- Form Factor: Mini-ITX (170 mm x 170 mm)

More details at http://macchiatobin.net

Installation:

Write the Image to your Micro SD Card and insert it in the
MACCHIATObin Single Shot SD Card Slot.

In the U-Boot Environment:
   1. reset U-Boot environment:
      env default -a
      saveenv

   2. prepare U-Boot with boot script:
      setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000"
      saveenv

   or manually (hanging lines indicate wrapped one-line command):
      setenv fdt_name armada-8040-mcbin-singleshot.dtb
      setenv image_name Image
      setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr
         $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv
         bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
         $kernel_addr - $fdt_addr'
      saveenv

   On newer Bootloaders (18.12) the Variables have been changed, use:
      setenv fdt_name armada-8040-mcbin-singleshot.dtb
      setenv image_name Image
      setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr_r
         $image_name;ext4load mmc 1:1 $fdt_addr_r $fdt_name;setenv
         bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
         $kernel_addr_r - $fdt_addr_r'

Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: Alexandra Alth <alexandra@alth.de>
[add specs and installation as provided by Alexandra Alth]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-12 02:06:02 +02:00
Adrian Schmutzler
9faf9f8f23 mvebu: fix support for Marvell 8040 MACCHIATOBin
Between kernels 4.20 and 5.0, a new variant of this board has been
introduced ("Single Shot"), and the existing one has been renamed
with the appendix "Double Shot". [1]
This also adjusted the first compatible in the list:

marvell,armada8040-mcbin -> marvell,armada8040-mcbin-doubleshot

This patch updates the OpenWrt implementation of this device by
adjusting the relevant references to that compatible (i.e., our
board name).

To still provide support for 4.19 with our setup, this adds a
small patch to change the compatible there as well.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b1f0bbe2700051886b954192b6c1751233fe0f52

Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-07-11 18:38:42 +02:00