Update bison to 3.5.1
Use POSIX threads as the previous option is no longer valid
Disable NLS support to be consistent with other tools such as e2fsprogs and sed
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G : *:0F
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
Additonal notes
---------------
It is possible to flash back to stock by using tplink-safeloader to create
a sysupgrade image based on a stock update. After the first boot, it is
necessary upgrade to another stock image, otherwise subsequent boots
fail with LZMA ERROR 1 and you have to attach serial to recover the device.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
[remove DEVICE_VARS change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the TP-Link TL-WA850RE v2 to dynamic partitioning and
will allow to use this for ath79 as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update bison to 3.5
Release notes:
https://lists.gnu.org/archive/html/info-gnu/2019-12/msg00002.html
Note for future: release notes mention that YYPRINT macro is
declared deprecated, but apparently still works for now. I found
one possible use of that in scripts/config/zconf.tab.c_shipped
That might be modernized at some point, but as the file is synced
with the one from upstream Linux, it might get fixed there.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This patch updates "soft_ver" for TP-Link Archer C6 v2 (EU).
It makes possible to upload OpenWrt on lastest vendor's firmware
as the web-based updater checks for major.minor version during upload.
Due to that on next major/minor version update TP-Link will stop
us from using the web-based firmware update tool, so it will
require a new patch on soft_ver to match major and minor version.
Up to today's latest stock firmware the patch (major.minor.patch)
version does not matters, that allows downgrade from 1.1.4 to 1.1.1
but do not allow downgrade from 1.1.X to 1.0.X.
Signed-off-by: Anderson Vulczak <andi@andi.com.br>
Specification:
SoC: MediaTek MT7628AN
RAM: 64MiB
Flash: 8MiB
Wifi:
- 2.4GHz: MT7628AN
- 5GHz: MT7612EN
LAN: 1x 10/100 Mbps
Flash instructions:
Flash factory image through stock firmware WEB UI.
Back to stock is possible by using TFTP and stripping down the Firmware
provided by TP-Link to a initramfs.
The flash space between 0x650000 and 0x7f0000
is blank in the stock firmware so I left it out as well.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Add missing calls to `free` for variable `mem`.
Add missing call to `fclose` for variable `f`.
The same changes were made in both `mkfwimage.c` and `mkfwimage2.c`.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
Add missing `fclose` calls for file pointers `kern_fp`, `fs_fp`
and `out_fp`.
Not closing files could lead to resource leaks.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
Add missing calls to `free` for variable `buffer`.
This could lead to a memory leak.
Add missing call to `close` for file pointer `fdin`.
This could lead to a resource leak.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
Add missing calls to `fclose` in functions `write_img`, `write_rootfs`
and `write_kernel`.
The not-closed files could lead to resource leaks.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
This commit adds support for Ubiquiti ToughSwitch XP (and probably also
EdgeSwitch XP) devices. They are mostly based on the same hardware as
MX devices.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN.
Specifications
--------------
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled; only 6 supported), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately. The 5G LED is currently not supported, since the GPIOs couldn't
be determined.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console. Since the web upgrade overwrites
the boot loader, you might also brick your device.
Additional notes
----------------
MAC address assignment is based on stock-firmware. For me, the device
assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G
WiFi has a separate MAC with +2.
*:88 Ethernet/2.4G label, uboot 0x1fc00, userconfig 0x0158
*:89 unused userconfig 0x0160
*:8A 5G not present in flash
This seems to be the first ramips device with a TP-Link v1 header. The
original firmware has the string "EU" embedded, there might be some region-
checking going on during the firmware upgrade process. The original
firmware also contains U-Boot and thus overwrites the boot loader during
upgrade.
In order to flash back to stock, the first header and U-Boot need to be
stripped from the original firmware.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
This adds a "factory" image for the aircube-isp devices. Note that the
firmware can't be uploaded without prior special preparation. For the
most recent instructions on how to do that, visit the OpenWRT wiki page
of the Ubiquiti airCube ISP for details:
https://openwrt.org/toh/ubiquiti/ubiquiti_aircube_isp
Current procedure:
With the original firmware 2.5.0 it is possible to upload and execute a
script via the configuration. To do that download and unpack the
original configuration, adapt uhttpd config to execute another lua
handler (placed in the config directory) and pack and upload it again.
The lua handler can call a script that mounts an overlayfs and modifies
the "fwupdate.real" binary so that an unsigned image is accepted. The
overlayfs is necessary because a security system (called tomoyo) doesn't
allow binaries in other locations than /sbin/fwupdate.real (and maybe
some more) to access the flash when executed via network.
A big thanks to Torvald Menningen (Snap) from the OpenWRT forum for
finding out how to patch the binary so that it accepts an unsigned
image.
The current step-by-step procedure is:
- Use a version 2.5.0 of the original firmware. This is important
because a binary file will be modified.
- Download a configuration.
- Unpack it (it's just a tar gz file without an ending).
- Add the following to uhttpd:
``````
config 'uhttpd' 'other'
list listen_http 0.0.0.0:8080
list listen_http [::]:8080
option 'home' '/tmp/persistent/config/patch/www'
option lua_prefix '/lua'
option lua_handler '/tmp/persistent/config/patch/handler.lua'
``````
- Create a `patch` subfolder.
- Create a `patch/www` subfolder.
- Create a `patch/handler.lua` with the following content:
``````
function handle_request(env)
uhttpd.send("Status: 200 OK\r\n")
uhttpd.send("Content-Type: text/plain\r\n\r\n")
local command = "/bin/sh /tmp/persistent/config/patch/patch.sh 2>&1"
local proc = assert(io.popen(command))
for line in proc:lines() do
uhttpd.send(line.."\r\n")
end
proc:close()
end
``````
- Create a `patch/patch.sh` with the following content:
``````
#!/bin/sh -x
set -e
set -u
set -x
UBNTBOX_PATCHED="/tmp/fwupdate.real"
MD5FILE="/tmp/patchmd5"
cat <<EOF > ${MD5FILE}
c33235322da5baca5a7b237c09bc8df1 /sbin/fwupdate.real
EOF
# check md5 of files that will be patched
if ! md5sum -c ${MD5FILE}
then
echo "******** Error when checking files. Refuse to do anything. ********"
exit 0
fi
# prepare some overlay functionality
LOWERDIR="/tmp/lower_root"
mkdir -p ${LOWERDIR}
mount -t squashfs -oro /dev/mtdblock3 ${LOWERDIR}
overlay_some_path()
{
PATH_TO_OVERLAY=$1
ALIAS=$2
UPPERDIR="/tmp/over_${ALIAS}"
WORKDIR="/tmp/over_${ALIAS}_work"
mkdir -p ${UPPERDIR}
mkdir -p ${WORKDIR}
mount -t overlay -o lowerdir=${LOWERDIR}${PATH_TO_OVERLAY},upperdir=${UPPERDIR},workdir=${WORKDIR} overlay ${PATH_TO_OVERLAY}
}
# patch the ubntbox binary.
overlay_some_path "/sbin" "sbin"
echo -en '\x10' | dd of=/sbin/fwupdate.real conv=notrunc bs=1 count=1 seek=24598
echo "******** Done ********"
``````
- Repack the configuration.
- Upload it via the normal web interface.
- Wait about a minute. The webserver should restart.
- Now there is a second web server at port 8080 which can call the lua
script. Visit the page with a web browser. Link is for example
http://192.168.1.1:8080/lua
- You should see the output of the script with a "*** Done ***" at the
end. Note that the patches are not permanent. If you restart the
router you have to re-visit the link (but not re-upload the config).
- Now you can upload an unsigned binary via the normal web interface.
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
Its way more trouble to update this to a newer version of qemu than it
is to backport the two additional features we need.
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
This replaces tabs by spaces when preceding an equal sign. This improves
consistency in the file and makes the indent look correct on all platforms.
While at it, also fix one case of inconsistent leading spaces.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch is based on #1689 and adds support for TP-Link Archer
C6 v2 (US) and A6 (US/TW).
The hardware is the same as EU and RU variant, except for GPIOs
(LEDS/Buttons), flash(chip/partitions) and UART being available
on the board.
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q127CS1G (16MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: 115200, 8n1 (header available on board)
Known issues:
- Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range.
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherA6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the
reset button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
Flash partitioning: I've followed #1689 for defining the partition layout
for this patch. The partition named as "tplink" @ 0xfd0000 is marked
as read only as it is where some config for stock firmware are stored.
On stock firmware those stock partitions starts at 0xfd9400 however
I had not been able to make it functional starting on the same address as
on stock fw, so it has been partitioned following #1689 and not the stock
partition layout for this specific partition. Due to that firmware/rootfs
partition lenght is 0xf80000 and not 0xf89400 as stock.
According to the GPL code, the EU/RU/JP variant does have different GPIO pins
assignment to LEDs and buttons, also the flash memory layout is different.
GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz
Signed-off-by: Anderson Vulczak <andi@andi.com.br>
[wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases
to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to the SourceForge page, the project is migrating to GitHub.
Thus, change the source of the package to GitHub.
Signed-off-by: David Bauer <mail@david-bauer.net>
"2.0" instead of "2.00" is sufficient and more in line with the
other definitions.
Signed-off-by: Bernhard Geier <freifunk@geierb.de>
[commit message/title adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This adds support for a popular low-cost 2.4GHz N based AP
Specifications:
SoC: Qualcomm Atheros QCA9533 (650MHz)
RAM: 64MB
Storage: 8 MB SPI NOR
Wireless: 2.4GHz N based built into SoC 2x2
Ethernet: 2x 100/10 Mbps, integrated into SoC
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
This also applies some minor changes to the common DTSI:
- use &wmac for label-mac-device, as this one is actually set up in
common DTSI
- move ð0 to parent DTSI
- fix several leading spaces, added/removed newlines
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[DTS style fixes/improvements, updated commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 43365ca662 ("Do not use $(V) - force AM_V=1") as
it breaks verbose output in automake packages, deviating from the
upstream and expected behaviour.
As you can see, neither make command outputs the expected verbose
compile command lines:
```
$ make package/mtd-utils/{clean,compile} V=sc
...
CCLD lsmtd
CC nand-utils/nanddump.o
CCLD nanddump
...
```
```
$ make -C build_dir/target*/mtd-utils-2.1.1 clean
...
$ make -C build_dir/target*/mtd-utils-2.1.1 V=1
...
CC lib/libmtd.o
CC lib/libfec.o
CC lib/common.o
CC lib/libcrc32.o
```
The original reason for this commit was some packages failing to build
if V is set to something other than 0 or 1. See the discussion in PR
https://github.com/openwrt/openwrt/pull/2481 for how to fix this in the
package Makefile.
Ref: PR#2481
Acked-by: Mirko Vogt <mirko-openwrt@nanl.de>
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
[commit title/description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with
two Ethernet ports based on Atheros AR9344
The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm
instead of 12 dBm) and two antenna connectors instead of built-in antennas.
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP: 192.168.0.100
Stock device TFTP adress: 192.168.0.254
The TP-Link WBS devices use the same GPIOs as the CPE devices,
except for the link4 LED. For this one, WBS devices use "2", while
CPE devices use "16". (Tested on WBS210 v2)
Signed-off-by: Bernhard Geier <freifunk@geierb.de>
[added comment about GPIO]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"$(STAGING_DIR)/include" was carried over from buildroot-ng to OpenWrt
in commit 60c1f0f64d. buildroot has
dropped this directory a long time ago.
In OpenWrt the directory is still created by the PrepareStaging macro
and is part of the default TARGET_CPPFLAGS. But nothing at all installs
headers into this directory, nor should anything be installed under this
path.
Removing this directory from TARGET_CPPFLAGS will cut down the log noise
a bit. Not only will CPPFLAGS be shorter, there will be less warnings
set off by "-Wmissing-include-dirs" (or even failures when paired with
"-Werror"). After all the directory does not even _exist_ in the SDKs,
which are used on the build bots when building packages (see [1] and
[2]).
make[8]: Entering directory '/builder/shared-workdir/build/sdk/build_dir/target-aarch64_generic_musl/libmbim-1.20.0/src/common'
CC libmbim_common_la-mbim-common.lo
cc1: error: /builder/shared-workdir/build/sdk/staging_dir/target-aarch64_generic_musl/include: No such file or directory [-Werror=missing-include-dirs]
cc1: all warnings being treated as errors
[1] https://github.com/openwrt/packages/issues/10377
[2] https://github.com/openwrt/packages/pull/10378
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Rosen Penev <rosenp@gmail.com>
This fixes commit bae927c551 ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.
Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).
With this patch, we provide proper support for this device in ar71xx.
Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254
Fixes: bae927c551 ("ar71xx: add support for TP-LINK CPE510 V2.0")
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch removes scons host build tool, as commit 7087efd72a8d
("scons: move host build tool to a proper place") in the packages feed
has moved scons into the new home.
There are currently no packages in the master tree which would need
scons, yet scons is build always as part of host tools, just in order to
satisfy host build dependency of few packages in the packages feeds.
Ref: https://github.com/openwrt/packages/pull/9584
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This updates the U-Boot which provides the host tools like mkimage to
version 2019.07.
The patches were cleaned up and it was checked if this still compiles
on Linux and FreeBSD.
CONFIG_FIT_SIGNATURE_MAX_SIZE is set to the default value.
The patch for libressl was merged upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This has two improvements over the current version. An autotools fix and
application of the wrt350v2 patch.
Cleaned up Makefile as a result of makefiles being fixed.
Note that this package is not really used as it depends on orion, which is
classified as broken.
This is the last package that uses svn in the tree.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
