Fixes following missing kernel config symbol after adding GPIO watchdog:
Software watchdog (SOFT_WATCHDOG) [M/n/y/?] m
Watchdog device controlled through GPIO-line (GPIO_WATCHDOG) [Y/n/m/?] y
Register the watchdog as early as possible (GPIO_WATCHDOG_ARCH_INITCALL) [N/y/?] (NEW)
Fixes: 1a97c03d86 ("rampis: feed zbt-we1026 external watchdog")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Wavlink WL-WN535K1 is a "mesh" router with 2 gigabit ethernet ports
and one fast ethernet port. Mine is branded as Talius TAL-WMESH1.
It can be found in kits of 2 or 3 (WL-WN535K2 or WL-WN535K3).
The motherboard is labelled as WS-WN535G3-B-V1.2 so this image could
potentially work for WL-WN535G3R and WS-WN535G3R with little to none
effort, but it's untested.
Hardware
--------
SoC: Mediatek MT7620A
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
- 2x 10/100/1000 Mbps Ethernet (RTL8211F)
- 1x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 internal antennas
BTN:
- 1x Reset button
- 1x Touchlink button (set to WPS)
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 3x Green leds (ethernet port status/act)
UART:
- 57600-8-N-1
Everything works correctly.
Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.
Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on WN535K1_V1510_200916 firmware version.
1) Go to http://192.168.10.1/webcmd.shtml
2) Type the following line in the "Command" input box and then press enter:
mkdir /etc_ro/lighttpd/www/dev; dd if=/dev/mtd0ro of=/etc_ro/lighttpd/www/dev/mtd0ro
3) After few seconds in the textarea should appear this output:
16384+0 records in
16384+0 records out
If your output doesn't match mine, stop reading and ask for
help in the forum.
4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
content of the whole NOR. If the file size is 0 byte, stop reading
and ask for help in the forum.
5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
rm /etc_ro/lighttpd/www/dev/mtd0ro;for i in 1 2 3 4 5; do dd if=/dev/mtd${i}ro of=/etc_ro/lighttpd/www/dev/mtd${i}ro; done
6) After few seconds, in the textarea should appear this output:
384+0 records in
384+0 records out
128+0 records in
128+0 records out
128+0 records in
128+0 records out
14720+0 records in
14720+0 records out
1024+0 records in
1024+0 records out
If your output doesn't match mine, stop reading and ask for
help in the forum.
7) Open the following links to download the partitions of the OEM FW:
http://192.168.10.1/dev/mtd1rohttp://192.168.10.1/dev/mtd2rohttp://192.168.10.1/dev/mtd3rohttp://192.168.10.1/dev/mtd4rohttp://192.168.10.1/dev/mtd5ro
If one (or more) of these files are 0 byte, stop reading and ask
for help in the forum.
8) Store these downloaded files in a safe place.
9) Reboot your router to remove any temporary file in ram.
Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update_mesh.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:E2 (factory @ 0x28)
WAN XX:XX:XX:XX:XX:E3 (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:E4 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:E5 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:E5
2) The OEM firmware upgrade page accepts only files containing the
string "WN535K1" in the filename.
3) Additional notes 1,2,3 in the WS-WN583A6 commit are still valid
(92780d80ab)
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router,
based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB (MXIC MX25L6405D)
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610E
- Ethernet: 1x 10/100Mbps
- Switch: SoC internal
- UART: J2 (57600 8N1)
- pinout: [3V3] (RXD) (GND) (TXD)
Installation and Recovery via TFTP:
1. Connect ethernet cable between Router port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
You can use any TFTP client. (tftp, curl, Tftpd64...)
5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!**
The device will be automatically rebooted.
Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on
MediaTek MT7620A.
Specifications:
* SoC: MT7620A
* RAM: 64 MiB
* Flash: SPI NOR 16 MiB
* USB & SATA bridge controller: JMicron JMS567
* SATA 6Gb/s: 2.5" drive slot
* USB 3.0: Micro-B
* USB 2.0: connected to SoC
* Wi-Fi:
* 2.4 GHz: SoC built-in
* 5 GHz: MT7612EN
* Ethernet: 5x 1GbE
* Switch: MT7530WU
* UART: 4-pin 1.27 mm pitch through-hole (57600 baud)
* Pinout: (3V3)|(RXD) (TXD) (GND)
Notes:
* The drive is accessible through the external USB port only when the
router is turned off.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
The image filename should have ".upload" extension.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
In 20b09a2125 Lava LR-25G001 router have problem with two inactive
ethernet ports. JBOOT bootloader didn't configure ethernet devices by default.
The same situation was there. It is required to enable all phy ports.
This is fragment of stock bootlog:
switch reg write_athr offset=90, value=2b0
switch reg write_athr offset=8c, value=2b0
switch reg write_athr offset=88, value=2b0
switch reg write_athr offset=84, value=2b0
switch reg write_athr offset=80, value=2b0
This patch adds proper registers configuration ar8337 initvals.
0x2b0 value causes force flow control configuration, 0x1200 was used
instead (flow control config auto-neg with phy). [1]
When switch is now ok, let's fix port numeration too.
Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")
[1] https://github.com/openwrt/openwrt/pull/4806#issuecomment-982019858
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
LED labels for this device are different in 01_leds file and in device
DTS. Switch to DT triggers, which works on Telewell TW-4 (LTE) clone
device.
This has not been tested on the LR-25G001 itself, just on the clone
mentioned above.
Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")
Signed-off-by: Jani Partanen <rtfm@iki.fi>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Give users more control by exposing ephy leds.
Signed-off-by: David Yang <mmyangfl@gmail.com>
[remove execute bit on 01_leds, add status for gpio2]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SOC: MT7620A + MT7610E
* ROM: 16 MiB spi flash (W25Q128FVSG)
* RAM: 128 MiB DDR2 (W971GG6KB-25)
* WAN: 10/100M *1
* LAN: 10/100M *4
* USB: Type-A USB2.0 *1
* SD: MicroSD *1
* Button: Reset *1
* Antennas: 2.4 GHz *2 + 5 GHz *1
* TTL Baudrate: 57600
* U-Boot Recovery: IP: 10.10.10.123, Server: 10.10.10.3
Installation:
* Web UI Update
1. Open http://192.168.10.1/upgrade.html in the browser.
2. Rename firmware to a short name like firmware.bin and then upload it.
3. Fill in the password column with the following content:
password | mtd -x mIp2osnRG3qZGdIlQPh1 -r write /tmp/firmware.bin firmware
* TFTP + U-Boot
1. Connect device with a TTL cable.
2. Press "2" when booting to select "Load system code then write to Flash via TFTP".
3. Upload firmware by tftpd64, it will boot when write instruction is executed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Descriptions：
Phicomm K2 (PSG1218) got a new "permanent_config" partition after
update firmware to v22.5. This partition located in front of the
firmware partition, same as The Phicomm K2P and K2G. Due to this
change the new bootloader can't load previous firmware any more.
This commit is aimed at add support for Phicomm K2 which official
firmware version is 22.5.x or newer. For which runs old firmware
version, just update OpenWrt that has a prefix of "k2-v22.4".
For uniform naming, this commit also changed the model name
PSG1218 to a more recognizable name K2, refer to Phicomm K2G,
K2P K2T.
OpenWrt selection table:
official firmware version OpenWrt
v22.4.x.x or older phicomm_k2-v22.4
v22.5.x.x or newer phicomm_k2-v22.5
Installation:
Same as Phicomm K2G, K2P, PSG1208.
a. TFTP + U-Boot
b. Open telnet by some web page vulnerability (Search Baidu by key
words "K2 telnet"), and then we can upload firmware image to
/tmp and write it to firmware partition with mtd instruction.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[rebase, add/harmonize version in model variables, fix version typo
in commit message, wrap commit message properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MAC address retrieval was switched to more generic upstream (5.13) NVMEM
based solution in commit 06bb4a5018 ("ramips: convert mtd-mac-address
to nvmem implementation") , but NVMEM subsystem wasn't enabled in the
kernel, so fix it now.
References: https://github.com/openwrt/openwrt/pull/4041#issuecomment-883322801
Fixes: 06bb4a5018 ("ramips: convert mtd-mac-address to nvmem implementation")
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message]
This adds a driver for the AW9523 I2C GPIO expander.
This driver is required to make LEDs as well as buttons on the Tenbay
T-MB5EU-V01 work.
This driver already had several upstream iterations. I'm working to
push this driver to mainline.
Ref: https://patchwork.ozlabs.org/project/linux-gpio/list/?series=226287
Signed-off-by: David Bauer <mail@david-bauer.net>
These boards have AR8327 or QCA8337 external ethernet switch.
The SOC also has it's own internal switch
where VLAN is now enabled by default.
Changes to preinit caused all switches to have VLANs enabled by default
even if they are not configured with a topology in uci_defaults
(see commit f017f617ae)
When both internal and external switches have VLANs,
and the external switch has both LAN and WAN,
the TX traffic from the SOC cannot flow to the tagged port on the external switch
because the VLAN IDs are not matching.
So disable the internal switch VLANs by default on these boards.
Also, add a topology for the internal switch,
so that on LuCI there is not an "unknown topology" warning.
In theory, it may be possible to have LAN ports on both switches
through internal and external PHYs, but there are no known boards that have this.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
About the device
----------------
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M
FLASH: 8MB
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 2x (RTL8211F)
BTN: - WPS
- Reset
- Router/Repeater/AP (3-way slide-switch)
LED: - WPS (blue)
- 3-segment Wifi signal representation (blue)
- WiFi (blue)
- WAN (blue)
- LAN (blue)
- Power (blue)
UART: UART is present as Pads with through-holes on the PCB. They are
located next to the reset button and are labelled Vcc/TX/RX/GND as
appropriate. Use 3.3V, 57600-8N1.
Installation
------------
Using the webcmd interface
--------------------------
Warning: Do not update to the latest Wavlink firmware (version
20201201) as this removes the webcmd console and you will need to
use the serial port instead.
You will need to have built uboot/sqauashfs image for this device,
and you will need to provide an HTTP service where the image can
be downloaded from that is accessible by the device.
You cannot use the device manufacturers firmware upgrade interface
as it rejects the OpenWrt image.
1. Log into the device's admin portal. This is necessary to
authenticate you as a user in order to be able to access the
webcmd interface.
2. Navigate to http://<device-ip>/webcmd.shtml - you can access
the console directly through this page, or you may wish to
launch the installed `telnetd` and use telnet instead.
* Using telnet is recommended since it provides a more
convenient shell interface that the web form.
* Launch telnetd from the form with the command `telnetd`.
* Check the port that telnetd is running on using
`netstat -antp|grep telnetd`, it is likely to be 2323.
* Connect to the target using `telnet`. The username should
be `admin2860`, and the password is your admin password.
3. On the target use `curl` to download the image.
e.g. `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\
wavlink_wl-wn579x3-squashfs-sysupgrade.bin`.
Check the hash using `md5sum`.
4. Use the mtd_write command to flash the image.
* The flash partition should be mtd4, but check
/sys/class/mtd/mtd4/name first. The partition should be
called 'Kernel'.
* To flash use the following command:
`mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>`
Where mtd<n> is the Kernel partition, and <image-file> is
the OpenWrt image previously downloaded.
* The command above will erase, flash and then reboot the
device. Once it reboots it will be running OpenWrt.
Connect via ssh to the device at 192.168.1.1 on the LAN port.
The WAN port will be configured via DHCP.
Using the serial port
---------------------
The device uses uboot like many other MT7260a based boards. To
use this interface, you will need to connect to the serial
interface, and provide a TFTP server. At boot follow the
bootloader menu and select option 2 to erase/flash the image.
Provide the address and filename details for the tftp server.
The bootloader will do the rest.
Once the image is flashed, the board will boot into OpenWrt. The
console is available over the serial port.
Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
Device specifications:
* Model: Youku YK-L1/L1c
* CPU: MT7620A
* RAM: 128 MiB
* Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c)
* LAN: 2* 10M/100M Ports
* WAN: 1* 10M/100M Port
* USB: 1* USB2.0
* SD: 1* MicroSD socket
* UART: 1* TTL, Baudrate 57600
Descriptions:
Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look
really different, the only hardware difference between the two models is flash
size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can
compatible with YK-L1's firmware but it's better to split it to different models.
It is easy to identify the models by looking at the label on the bottom of the
device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash
sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update"
to install compatible firmware, so please backup config file before system upgrade.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[use more specific name for DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MAC addresses read from official firmware
value location
Wlan xx 71 de factory@0x04
Lan xx 71 dd factory@0x28
Wan xx 71 df factory@0x2e
Label xx 71 dd factory@0x28
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix sorting in 02_network, redact commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
1. rename led pin "air" to a more common name "wlan" and use "phy0tpt" to trigger it.
2. led "wan" can be triggered by ethernet pinctrl by default so just drop it.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
There are only two lan ports and one wan port on Youku yk1
Fixes: e9baf8265b ("ramips: add support for Youku YK1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit b4aad29a1d.
This was accidentally folded into a single commit. Remove it and
apply it properly again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enable testing kernel.
Delete upstreamed patches:
0098-disable_cm.patch can be dropped, upstream fixed CM handling.
Fix compile errors by using new kernel APIs.
Fix fuzz by manually editing patches to ensure the code goes in the
right place.
For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit
a307593a6 to keep the OpenWrt ralink driver operational.
Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693
and #3952.
Rename patches to follow the 3-digit classification from the OpenWrt
Developer Guide.
Run automatic quilt refresh.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
The lan port sequence was reversed compared to the labels.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Phicomm K2G:
add missing label_mac
Phicomm PSG1218A & PSG1218B:
The previous wan mac was set as factory@0x28 +1 (originally based
on the default case for the ramips target), but the correct wan mac
is factory@0x28 -1, being equal to factory@0x2e.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On a platform with many very different devices, like found on ramips,
the generic profiles seem like remnants of the past that do not
have a real use anymore.
Remove them to have one thing less to maintain.
Actually, rt288x didn't have a default profile in the first place.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
Same hardware as Phicomm K2G but different flash layout.
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped
with external PA.
- UART: 1 x UART on PCB - 57600 8N1
Flash instruction:
To avoid requiring UART for TFTP a dual flash procedure is suggested
to install the squashfs image:
1. Rename openwrt-ramips-mt7620-wavlink_wl-wn530hg4-initramfs-kernel.bin
to WN530HG4-WAVLINK.
2. Flash this file with the factory web interface.
3. With OpenWRT now running use standard sysupgrade to install the
squashfs image.
Signed-off-by: Nuno Goncalves <nunojpg@gmail.com>
[remove dts-v1, remove model from LED labels, wrap commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While we mostly use the ucidef_set_led_* functions directly in 01_leds
we still have the set_wifi_led function in parallel for several old
devices. This is not only inconsistent with the other definitions,
it also links to the wlan0 interface instead of using a phy trigger
which would be independent of the interface name (and is used for
all newer devices anyway). Apart from that, the standard names
"wifi" and "wifi-led" are not very helpful in a world with different
radio bands either.
Thus, this patch removes the set_wifi_led function and puts the
relevant commands into the cases explicitly. This makes the
mechanism used more evident and will hopefully lead to some future
improvements or at least prevent some copy-pasting of the old
setups.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In ramips, it's not common to use an alias for specifying the WiFi
LED; actually only one device uses this mechanism (TL-WR841N v14).
Particularly since the WiFi LEDs are typically distinguished between
2.4G and 5G etc. it is also not very useful for this target.
Thus, this patch removes the setup lines for this mechanism and
converts the TL-WR841N v14 to the normal setup.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patch for ath79 target, this will remove the
"devicename" from LED labels in ramips as well.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated.
For the latter, all existing definitions were actually just
devicename migrations anyway. Therefore, those are removed and
a common migration file is created in target base-files. This is
actually another example of how the devicename removal makes things
easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to the User Manual, there is a "Wi-Fi LED" with blue and
green colors, doing the following by default:
Flashing Blue: System loading
Solid Blue: System loaded
Flashing Green: Connecting to the Internet
Solid Green: Connected to the Internet
According to this vendor behavior, we keep refer to the LED as "wifi"
but implement the according default behavior as in OEM firmware.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.
To address this, use the lzma loader (loader-okli) to work around this
limitation.
The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.
Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port.
Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli).
Specifications:
SOC: MediaTek MT7620N
BATTERY: 10400mAh
WLAN: 802.11bgn
LAN: 1x 10/100 Mbps Ethernet
USB: 1x USB 2.0 (Type-A)
RAM: 64 MB
FLASH: GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz
Flash itself specified to 80 MHz, but speed limited by mt7620 SPI
fast-read enabled (m25p)
LED: Status LED (blue after boot, green with WiFi traffic
4 leds to indicate power level of the battery (unable to control)
INPUT: Power, reset button
MAC assignment based on vendor firmware:
2.4 GHz *:b4 (factory 0x04)
LAN/label *:b4 (factory 0x28)
WAN *:b5 (factory 0x2e)
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- Installation from TFTP (recovery)
- OpenWRT sysupgrade (Preserving and non-preserving), through the usual
ways: command line and LuCI
- LEDs (except as noted above)
- Button (reset)
- I2C, which is needed for reading battery charge status and level
- U-Boot environment / variables (from U-Boot, and OpenWrt)
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel
- ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
I would like to thank @mpratt14 and @xabolcs for their help getting the
lzma loader to work!
Signed-off-by: Russell Morris <rmorris@rkmorris.us>
[drop changes in image/Makefile, fix indent and PKG_RELEASE in
uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift,
add COMPILE to Device/Default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The target seems to be working on 5.4, so drop 4.14 support in
preparation for removing it from master entirely.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.
Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
- CPU: MediaTek MT7620N (580 MHz)
- Flash size: 4 MB NOR SPI
- RAM size: 32 MB DDR1
- Bootloader: U-Boot
- Wireless: MT7620N 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Switch: MT7620 built-in 10/100 switch with vlan support
- Ports: 4x LAN, 1x WAN
- Others: 7x LED, Reset button, UART header on PCB (57600 8N1)
Flash instructions:
1. Use ethernet cable to connect router with PC/Laptop, any router
LAN port will work.
2. To flash openwrt we are using nmrpflash[1].
3. Flash commands:
First we need to identify the correct Ethernet id.
nmrpflash -L
nmrpflash -i net* -f openwrt-ramips-mt7620-netgear_jwnr2010-v5-squashfs-factory.img
This will show something like "Advertising NMRP server on net*..." (net*, *=1,2,3... etc.)
4. Now remove the power cable from router back side and immediately connect it again.
You will see flash notification in CMD window, once it says reboot the device just
plug off the router and plug in again.
Revert to stock:
1. Download the stock firmware from official netgear support[2].
2. Follow the same nmrpflash procedure like above, this time just use the stock firmware.
nmrpflash -i net* -f N300-V1.1.0.54_1.0.1.img
MAC addresses on stock firmware:
LAN = *:28 (label)
WAN = *:29
WLAN = *:28
On flash, the only valid MAC address is found in factory 0x4.
Special Note:
This openwrt firmware will also support other netgear N300 routers like below as they
share same stock firmware[3].
JNR1010v2 / WNR614 / WNR618 / JWNR2000v5 / WNR2020 / WNR1000v4 / WNR2020v2 / WNR2050
[1] https://github.com/jclehner/nmrpflash
[2] https://www.netgear.com/support/product/JWNR2010v5.aspx
[3] http://kb.netgear.com/000059663
Signed-off-by: Shibajee Roy <ador250@protonmail.com>
[create DTSI, use netgear_sercomm_nor, disable by default, add MAC
addresses to commit message, add label MAC address]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
RT3x5x seems to work fine with kernel 5.4. Set the default kernel
version to 5.4 to bring this to a broader audience.
Since 4 of 6 targets are on kernel 5.4 now, invert the kernel
version setup logic in Makefile/target.mk files.
Tested on ZyXEL Keenetic.
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[invert version setup logic]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MT7620 seems to work fine with kernel 5.4. Set the default kernel
version to 5.4 to bring this to a broader audience.
Tested on Archer C2 v1 / Archer C20i
Signed-off-by: David Bauer <mail@david-bauer.net>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This updates the display port order for the TEW-810DR to be in line
with the DIR-810L. Both share the same board and pictures on the
vendors' pages indicate the same external numbering scheme as well.
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
[replace commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The port order displayed in LuCI is currently inverted for this
devices:
LuCI - Device
LAN1 - LAN4
LAN2 - LAN3
LAN3 - LAN2
LAN4 - LAN1
Fix it.
Strangely, the owner of a TRENDnet TEW-810DR reports that the
initial port order is correct, while both devices share the
same board and look similar from the outside. Since I cannot
investigate this without having any of the devices, this does
only touch the DIR-810L for now.
While at it, also merge in the case for zbtlink,zbt-we2026, as
the display port specified for WAN there won't have any effect
anyway.
Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
