Commit Graph

29069 Commits

Author SHA1 Message Date
John Audia
6c118efc01 kernel: bump 5.15 to 5.15.140
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.140

Removed upstreamed:
	mvebu/patches-5.15/106-Revert-i2c-pxa-move-to-generic-GPIO-recovery.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.140&id=06d320ca170b4e59bb261e2ce3ffe84e9154d42b

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-11-29 23:41:33 +01:00
John Audia
c20bedf1f5 kernel: bump 6.1 to 6.1.64
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.64

Removed upstreamed:
	ixp4xx/patches-6.1/0001-mtd-cfi_cmdset_0001-Byte-swap-OTP-info.patch[1]
	mvebu/patches-6.1/106-Revert-i2c-pxa-move-to-generic-GPIO-recovery.patch[2]
	qualcommax/patches-6.1/0026-v6.7-clk-qcom-ipq8074-drop-the-CLK_SET_RATE_PARENT-flag-f.patch[3]

Manually rebased:
	bcm27xx/patches-6.1/950-0111-MMC-added-alternative-MMC-driver.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.64&id=3b93096d29c5b9ca2af94be4ee9949c1767acf17
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.64&id=b3fd9db79e30d5eb5f76ef1f5b7e4f444af574ea
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.64&id=877080a3490102da26b8d969588159b2385f739e

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-11-29 23:38:39 +01:00
Daniel Golle
507ad4f078 mediatek: add kmod-usb3 to default package set of the ZBT-Z8102AX
Include XHCI USB drivers on the ZBT-Z8102AX router, the drivers are
required to be able to use the USB-connected M.2 slots for 4G/5G modems.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-29 21:13:32 +00:00
David Bauer
6b73d9bf49 mediatek: copy config for Acer Predator W6
Config was previously not copied on sysupgrade.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-11-27 08:02:41 +01:00
David Bauer
1239668648 mediatek: add support for GL.iNet GL-MT2500
Hardware
--------
SoC:  MediaTek MT7981BA
RAM:  1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC:  8GB eMMC (Samsung 8GTF4R)
ETH:  1000Base-T LAN (ePHY)
      2500Base-T WAN (MaxLinear GPY211C)
BTN:  1x Reset Button
LED:  System (blue/white)
      VPN (white)
USB:  1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
      Don't connect 3.3V!

Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!

Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-11-27 08:02:41 +01:00
David Bauer
54e52fdacb rockchip: require image metadata
All devices in the rockchip target have appended image-metadata. Enforce
the presence of this metadata to avoid flashing incomplete images.

This is the de-facto standard for almost all OpenWrt targets.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-11-27 07:54:00 +01:00
Lech Perczak
32098554d9
ath79: fortinet-fap-221-b: convert to nvmem-layout
Now that MAC address parser supports the hex format (without
delimiters), use the canonical MAC address stored in U-boot partition.
Get rid of the userspace adjustments which are no longer necessary.
While at that, move the mac-base to the common part, as it is again
exactly the same in both models.

And convert ART partition too - keep that one separate, as calibration
data length differs between the models.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2023-11-27 00:34:49 +01:00
Lech Perczak
7e5e010035
ath79: fortinet-fap-220-b: convert to nvmem-layout
Now that MAC address parser supports the hex format (without
delimiters), use the canonical MAC address stored in U-boot partition.
Get rid of the "mac-address-increment" binding.
While at that, convert ART partition too.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2023-11-27 00:34:49 +01:00
Lech Perczak
cee7622ab0
ath79: fortinet-fap-220-b: fix WLAN MAC addresses
Addresses were swapped compared to the factory firmware. In addition to
that, one of them was shifted by -1. Fix that by setting wlan0 MAC
offset to 9, and wlan1 MAC offset to 2.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2023-11-27 00:34:49 +01:00
Xiaojun Liu
5899689159 x86 64: Add new device Cordoba Edge Platform
Add new device Cordoba Edge Platform
hardware specifications: CPU - Intel Atom C3000
                           Ethernet - 2 10Gbps ixgbe SPF+
                                      2 1Gbps  ixgbe RJ45/SPF
                                      4 2.5Gbps  igc RJ45
                           WiFi - mt7915e
                           LED  - 3 multicolor(red|blue|green) LEDs

Signed-off-by: Xiaojun Liu <xiaojun.liu@silicom.co.il>
2023-11-26 20:03:59 +01:00
Tianling Shen
4e09722a68 rockchip: add NanoPi R5C support
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
1GB or 4GB LPDDR4X RAM
2x 2500 Base-T
4 LEDs (LAN / WAN / WIFI / POWER)
1 Button (Reset)
8GB or 32GB eMMC on-board
Micro-SD Slot
M.2 Slot
2x USB 3.0 Port

Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tianling Shen
c06a71f0b3 rockchip: add NanoPi R5S support
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
2GB or 4GB LPDDR4X RAM
1x 1000 Base-T
2x 2500 Base-T
4 LEDs (LAN1 / LAN2 / WAN / POWER)
8GB eMMC on-board
Micro-SD Slot
M.2 Slot
2x USB 3.0 Port

Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.

Tested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tianling Shen
4d9059aed9 rockchip: armv8: broaden boardname
Now we have rk356x support :-)

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tianling Shen
4be1e39c4e rockchip: enable drivers for rk356x
Enable all necessary drivers for the rk356x SoCs, including PHY,
SCMI, SPI etc. Also backport 2 upstream patches for sdhci fixes.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tianling Shen
22a9c4b67d rockchip: remove kernel 5.15 patches and config
As we switched to kernel 6.1, these files can go.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tianling Shen
48c9a4b47c rockchip: switch to kernel 6.1
Required by the following rk3568 support.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tianling Shen
dd8972fde3 rockchip: move image generation command to default
It's applicable for all devices so move it to default to reduce
redudant code. Addtionally introduce a new variable `BOOT_SCRIPT`
to allow custom boot script (if necessary).

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tony Ambardar
a7818e0550 ipq40xx: enable UBI size checks for some Linksys NAND devices
Add correct NAND_SIZE in device definitions for EA6350v3, EA8300, MR8300,
WHW01 and WHW03v2, to enable improved image size checks wrt UBI reserved
blocks on NAND devices.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2023-11-26 18:37:21 +01:00
Tony Ambardar
b16e14a220 image: use helper function for size units
Add the make function 'exp_units' for helping evaluate k/m/g size units in
expressions, and use this to consistently replace many ad hoc substitutions
like '$(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE)))' in makefiles.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2023-11-26 18:37:20 +01:00
Tony Ambardar
c66511bc48 ipq40xx: fix typo in Linksys WHW01 image definition
Use lower-case "k" in IMAGE_SIZE for Linksys WHW01, permitting proper unit
conversions in build recipes (e.g. 75776k -> 75776*1024).

Fixes: 2a9f3b7717 ("ipq40xx: fix up Linksys WHW01 board name, device definition")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2023-11-26 18:37:20 +01:00
Rani Hod
e29f4a3f70 ath79: add support for D-link DAP-1720 A1
D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender,
manufactured by Alpha Networks [8WAPAC28.1A1G].
(in square brackets: PCB silkscreen markings)

Specifications:
* CPU (Qualcomm Atheros QCA9563-AL3A [U5]):
  775 MHz single core MIPS 74Kc;
* RAM (Winbond W9751G6KB-25J [U3]):
  64 MiB DDR2;
* ROM (Winbond W25Q128FV [U16]):
  16 MiB SPI NOR flash;
* Ethernet (AR8033-AL1A PHY [U1], no switch):
  1 GbE RJ45 port (no PHY LEDs);
* Wi-Fi
  * 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]):
    3x3 802.11n;
  * 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]):
    3x3 802.11ac Wave 1;
  * 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3];
* GPIO LEDs:
  * RSSI low (red/green) [D2];
  * RSSI medium (green) [D3];
  * RSSI high (green) [D4];
  * status (red/green) [D5];
* GPIO buttons:
  * WPS [SW1], co-located with status LED;
  * reset [SW4], accessible via hole in the side;
* Serial/UART:
  Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch;
  125000-8-n-1 in U-boot, 115200-8-n-1 in kernel;
* Misc:
  * 12V VCC [JP2], fed from internal 12V/1A AC to DC converter;
  * on/off slide switch [SW2] (disconnects VCC mechanically);
  * unpopulated footprints for a Wi-Fi LED [D1];
  * unpopulated footprints for a 4-pin 3-position slide switch (SW3);

MAC addresses:
* Label = LAN;
* 2.4 GHz WiFi = LAN;
* 5 GHz WiFi = LAN+2;

Installation:
* `factory.bin` can be used to install OpenWrt from OEM firmware via the
  standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html
* `recovery.bin` can be used to install OpenWrt (or revert to OEM
  firmware) from D-Link Web Recovery. To enter web recovery, keep reset
  button pressed and then power on the device. Reset button can be
  released when the red status LED is bright; it will then blink slowly.
  Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and
  upload 'recovery.bin'. Note that in web recovery mode the device
  ignores ping and DHCP requests.

Note: 802.11s is not supported by the default `ath10k` driver and
firmware, but is supported by the non-CT driver and firmware variants.
The `-smallbuffers` driver variant is recommended due to RAM size.

Co-developed-by: Anthony Sepa <protectivedad@gmail.com>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-11-26 18:27:35 +01:00
Rosen Penev
b7f26c6392 ath79: ar: convert to mac-base
Replacement for deprecated mac-address-increment

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 21:34:18 -08:00
Rosen Penev
9783340af9 ath79: ar: convert to nvmem-layout
Will allow removing deprecated mac-address-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 21:34:18 -08:00
Rosen Penev
de1d9da150 ath79: tp9343: convert to nvmem-layout
Allows getting rid of deprecated mac-address-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 19:43:35 -08:00
Rosen Penev
ede82f35eb ath79: qcn: convert to nvmem-layout
Allows getting rid of deprecated mac-address-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 19:43:32 -08:00
Rosen Penev
b2f1c6ed52 ath79: qca: remove mac-address-increment
nvmem-layout allows removal

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 17:14:04 -08:00
Rosen Penev
e816591e22 ath79: qca: convert to nvmem-layout
Allows replacing mac-address-increment with mac-base.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 17:14:04 -08:00
Rosen Penev
eea4dfaa7b ath79: mikrotik: fix dts warnings
property has invalid length

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 17:14:04 -08:00
Rosen Penev
3395184825
ramips: mt7621: nix mac-address-increment
nvmem-layout allows removal

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-26 01:30:32 +01:00
Rosen Penev
f4c33d098f
ramips: mt7621: convert to nvmem-layout
Allows replacing mac-address-increment with mac-base.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-26 01:30:32 +01:00
Rosen Penev
3c1c3f4685
ramips: mt7621: add interrupt-controller
Fixes dtc warning:

'#interrupt-cells' found, but node is not an interrupt provider

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-26 01:30:04 +01:00
Rosen Penev
458cb2cd6b
ramips: mt7620a: use mac-base
mac-address-increment is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-26 00:15:58 +01:00
Rosen Penev
40feb97e56
ramips: mt7620a: convert to nvmem-layout
Allows using mac-base to replace mac-address-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-26 00:15:58 +01:00
Rosen Penev
32c1ac8960
ramips: mt7620n: convert to nvmem-layout
nvmem-cells is deprecated. nvmem-layout allows using mac-base.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-26 00:15:55 +01:00
Rosen Penev
e8084a3c3b
ramips: mt7628: use mac-base
mac-address-increment is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:58:44 +01:00
Rosen Penev
0a1d15642f
ramips: mt7628: use nvmem-layout
Will allow using mac-base.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:58:40 +01:00
Rosen Penev
3eb899fd36
mediatek: use mac-base
mac-address-increment is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:45:26 +01:00
Rosen Penev
405bc5be13
mediatek: convert to nvmem-layout
Will allow removing mac-address-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:45:26 +01:00
Rosen Penev
b976fa5d2b
ramips: rtxxxx: remove mac-address-increment
Deprecated and replaced upstream with mac-base.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:39:52 +01:00
Rosen Penev
5f479a4f34
ramips: rtxxxx: convert to nvmem-layout
Allows replacing mac-adress-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:39:47 +01:00
Chukun Pan
07482d15af
mediatek: filogic: reorder alphabetically
Reorder scripts and image recipes to keep alphabetical order.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-25 23:16:35 +01:00
Chukun Pan
b74ae69596
mediatek: filogic: remove kmod-usb2 for GL-MT6000
The usb driver requires kmod-usb3, not kmod-usb2.
Remove the useless kmod-usb2 from default package.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-25 23:16:34 +01:00
Chukun Pan
1be6347b7d
mediatek: Cetron CT3003: fixes typo for spi properties
Same as commit 3674689, correct 'buswidth' to 'bus-width'.
Also move the nmbm properties outside the partition definition.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-25 23:16:34 +01:00
Rosen Penev
7e316bc53a
ipq40xx: remove mac-address-increment
nvmem-layout allows removal

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:14:54 +01:00
Rosen Penev
fe8dd23882
ipq40xx: convert to nvmem-layout
Allows replacing mac-address-increment with mac-base.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:14:54 +01:00
Rosen Penev
14467fd515
ipq40xx: fix dtc warnimg
I2C bus unit address format error, expected "62"

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:14:51 +01:00
Rosen Penev
eadf2ead4e
qualcommax: convert to nvmem-layout
nvmem-cells is deprecated

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 22:51:32 +01:00
Rosen Penev
10b7e2d0df
apm821xx: convert to nvmem-layout
nvmem-cells is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 22:50:32 +01:00
Hauke Mehrtens
d99aed31a0 mediatek: filogic: Fix GPIOs for Zbtlink ZBT-Z8102AX
The PGIO configuration should be added for the ZBT-Z8102AX and not the ZBT-Z8103AX

Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-11-25 22:25:42 +01:00
Xiaobo Liu
5fbb1f09ca ramips: mt76x8 add support for RTC class/drivers
This commit adds support for RTC class/drivers to the mt76x8 target.

Signed-off-by: Xiaobo Liu <cppcoffee@gmail.com>
2023-11-25 18:16:46 +01:00