Commit Graph

272 Commits

Author SHA1 Message Date
Adrian Schmutzler
f3921acdf0 ipq40xx: fix patches on dts Makefile
The patches for arch/arm/boot/dts/Makefile have not been updated
in a syntactically correct way (just body was changed). Fix it.

Fixes: 4a77a060ab ("ipq40xx: add support for Buffalo WTR-M2133HP")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 17:50:12 +02:00
Yanase Yuki
4a77a060ab ipq40xx: add support for Buffalo WTR-M2133HP
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.

Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A

Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
   and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
    # ubidetach -p /dev/mtd15
    # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
    # fw_setenv bootcmd bootipq
8. Perform reboot.

Recover to stock firmware
-------------------------
1. Execute the following command.
    # fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2020-07-08 16:07:05 +02:00
Dongming Han
f103321349 ipq40xx: add support for GL.iNet GL-S1300
Specifications:
SOC:        Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM:        512 MiB
FLASH1:     16 MiB NOR - SPI0
FLASH2:     8 GiB eMMC
ETH:        Qualcomm QCA8075
WLAN1:      Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2:      Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT:      Reset, WPS
LED:        Power, Mesh, WLAN
UART1:      On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2:      On board with BLE module
SPI1:       On board socket for Zigbee module

Install via tftp
- NB: need to flash transition image firstly

Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script

Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf

Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script

The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2020-07-08 16:07:05 +02:00
Hauke Mehrtens
6062d85892 kernel: Update kernel 4.19 to version 4.19.131
Fixes:
- CVE-2020-10757

The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.

Run tested: ath79
Build tested: ath79

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 21:12:42 +02:00
Adrian Schmutzler
e8afeaabc0 ipq40xx: set IMAGES in Device/Default definition
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.

Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 14:07:43 +02:00
Adrian Schmutzler
fa6d53261a ipq40xx: consolidate DTS files
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (qcom-ipq4018-emr3500.dts), which is only
present for 5.4.

Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory.

If there ever was a new kernel with substantial DTS changes, a
new folder would need to be introduced anyway and could easily be
done.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-23 21:02:26 +02:00
Petr Štetiar
e44e60b290 kernel: bump 5.4 to 5.4.48
Resolved merge conflict in the following patches:

 layerscape: 701-net-0213-dpaa2-eth-Add-CEETM-qdisc-support.patch
 ramips: 0013-owrt-hack-fix-mt7688-cache-issue.patch

Refreshed patches, removed upstreamed patch:

 bcm63xx: 020-v5.8-mtd-rawnand-brcmnand-fix-hamming-oob-layout.patch

Run tested: qemu-x86-64
Build tested: x86/64

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-22 12:51:22 +02:00
Adrian Schmutzler
48c1fdd046 treewide: drop shebang from non-executable target files
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.

While at it, fix the executable flag on a few of these files.

This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-16 14:26:33 +02:00
David Bauer
373f446049 ipq40xx: check kernel-size for NBG6617
The ZyXEL NBG6617 has a separate kernel partition which is 4MiB large.

Add the kernel size to validate the kernel won't be bigger than this
fixed limit.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-14 13:10:00 +02:00
David Bauer
5b50895a63 ipq40xx: add image size checks for several devices
This adds image size checks for various devies using an automatic
mtdsplit.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-14 13:09:59 +02:00
David Bauer
b8ed898f1b ipq40xx: use zImage for EX6100v2 and EX6150v2
The NETGEAR EX61500v2 and EX6150v2 U-Boot does not support booting LZMA
compressed images. Currently, they are using GZIP compressed kernels,
which results in ledd flash being available to the root and overlay
filesystems.

Using a zImage results in a smaller kernel and therefore increases
available space for rootfs and overlayfs.

Size reduced: ~1.1 MiB

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-13 16:57:53 +02:00
DENG Qingfang
752cee796d ipq40xx: disable DSA and Switchdev
ipq40xx is still using swconfig based switch management. This might
change in he future, however disable the DSA and Switchdev support for
now.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[rephrased commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-13 16:57:15 +02:00
Yen-Ting-Shen
3f61e5e1b9 ipq40xx: add support for EnGenius EMR3500
SOC:     IPQ4018 / QCA Dakota
CPU:     Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:    256 MiB
NOR:     32 MiB
ETH:     Qualcomm Atheros QCA8072 (2 ports)
USB:     1 x 2.0 (Host controller in the SoC)
WLAN1:   Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:   Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:   RESET Button
LEDS:    White, Blue, Red, Orange

Flash instruction:

From EnGenius firmware to OpenWrt firmware:

In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly.

From OpenWrt firmware to EnGenius firmware:

1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
   Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMR3500. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
   (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img
4. Flash the firmware
   (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
   (IPQ40xx) # reset

Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[squashed update patch, updated to 5.4, dropped BOARD_NAME,
migrated to SOC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-06-13 14:38:03 +02:00
Sven Eckelmann
6785695056 ipq40xx: essedma: Disable TCP segmentation offload for IPv6
It was noticed that the the whole MAC can hang when transferring data from
one ar40xx port (WAN ports) to the CPU and from the CPU back to another
ar40xx port (LAN ports). The CPU was doing only NATing in that process.

Usually, the problem first starts with a simple data corruption:

  $ wget https://cdimage.debian.org/debian-cd/current/amd64/iso-cd/debian-10.4.0-amd64-netinst.iso -O /dev/null
  ...
  Connecting to saimei.ftp.acc.umu.se (saimei.ftp.acc.umu.se)|2001:6b0:19::138|:443... connected.
  ...
  Read  error at byte 48807936/352321536 (Decryption has failed.). Retrying.

But after a short while, the whole MAC will stop to react. No traffic can
be transported anymore from the CPU port from/to the AR40xx PHY/switch and
the MAC has to be resetted.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: John Crispin <john@phrozen.org>
2020-06-13 14:38:03 +02:00
Adrian Schmutzler
2308644b0c ipq40xx: replace "ok" with "okay" for status in DTS files
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-12 19:16:41 +02:00
David Bauer
300b7fe85a ipq40xx: add support for Aruba AP-365
Hardware
--------
SoC:   Qualcomm IPQ4029
RAM:   512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
       - 4MB SPI-NOR (Macronix MX25R3235F)
TPM:   Atmel AT97SC3203
BLE:   Texas Instruments CC2540T
       attached to ttyMSM0
ETH:   Atheros AR8035
LED:   System (red / green / amber)
BTN:   Reset

The USB port on the device is (in contrast to other Aruba boards) real
USB. The AP uses a CP2101 USB TTY converter on the board.

Console baudrate is 9600 8n1.

To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.

Installation
------------

1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
   into the TFTP server root directory. Configure the TFTP server to
   be reachable at 192.168.1.75/24. Connect the machine running the TFTP
   server to the ethernet port of the access point.

2. Connect to the serial console. Interrupt autobooting by pressing
   Enter when prompted.

3. Configure the bootargs and bootcmd for OpenWrt.
   $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
   $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
     ubi read 0x85000000 kernel; bootm 0x85000000"
   $ setenv ramboot_openwrt "run bootargs_openwrt;
     setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
     netget; set fdt_high 0x87000000; bootm"
   $ setenv bootcmd "run nandboot_openwrt"
   $ saveenv

4. Load OpenWrt into RAM:
   $ run ramboot_openwrt

5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
   /tmp folder on the device.

6. Flash OpenWrt:
   Make sure you use the mtd partition with the label "ubi" here!

   $ ubidetach -p /dev/mtd1
   $ ubiformat /dev/mtd1
   $ sysupgrade -n /tmp/openwrt-sysupgrade.bin

To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:

  $ setenv bootcmd "boot"
  $ saveenv

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-11 01:05:16 +02:00
David Bauer
9fac9168c6 ipq40xx: fix alphabetical order in 02_network
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:03:41 +02:00
Petr Štetiar
faf668be35 kernel: bump 5.4 to 5.4.34
Refreshed patches.

Run tested: qemu-x86-64, apalis, a64-olinuxino
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-21 22:16:33 +02:00
Petr Štetiar
23916bca61 kernel: bump 5.4 to 5.4.33
Refreshed patches, removed upstreamed patches:

 oxnas: 001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch
 oxnas: 002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch

Run tested: qemu-x86-64, apalis
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-17 15:18:12 +02:00
Petr Štetiar
0bea89a1d0 kernel: bump 5.4 to 5.4.32
Refreshed patches, removed upstreamed patches:

 generic: 746-stable-net-dsa-mt7530-fix-null-pointer-dereferencing-in-por.patch

Run tested: qemu-x86-64, apalis
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-14 21:58:16 +02:00
Pawel Dembicki
c30220d458 ipq40xx: add support for Cell C RTL30VW
Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated
QMI mPCIE modem.

This is stripped version of ASKEY RTL0030VW.

Hardware:

Specification:
-CPU: IPQ4019
-RAM: 256MB
-Flash: NAND 128MB + NOR 16MB
-WiFi: Integrated bgn/ac
-LTE: mPCIe card (Modem chipset MDM9230)
-LAN: 2 Gigabit Ports
-USB: 2x USB2.0
-Serial console: RJ-45 115200 8n1
-Unsupported VoIP

Known issues:

None so far.

Instruction install:

There are two methods: Factory web-gui and serial + tftp.

Web-gui:
1. Apply factory image via stock web-gui.

Serial + initramfs:
1. Rename OpenWrt initramfs image to "image"
2. Connect serial console (115200,8n1)
3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4.

4. U-Boot commands:
sf probe && sf read 0x80000000 0x180000 0x10000
setenv serverip 192.168.1.4
set fdt_high 0x85000000
tftpboot 0x84000000 image
bootm 0x84000000

5. Install sysupgrade image via "sysupgrade -n"

Back to stock:

All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0,
do firstboot and factory reset with OFW:

1. read mtd8:
dd if=/dev/mtd8 of=/tmp/mtd8
2. go to tmp:
cd /tmp/
3. write first part of partition:
dd if=mtd8 of=mtd8.new bs=1 count=76
4. check which layout uses bootloader:
cat /proc/mtd
5a. If first are kernel_1 and rootfs_1 write 0:
echo -n -e '\x00' >> mtd8.new
5b. If first are kernel and rootfs write 1:
echo -n -e '\x01' >> mtd8.new
6. fill with rest of data:
dd if=mtd8 bs=1 skip=77 >> mtd8.new
7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with:
hexdump mtd8.new
8. write new mtd8 to flash:
mtd write mtd8.new /dev/mtd8
9. do firstboot
10.reboot
11. Do back to factory defaults in OFW GUI.

Based on work: Cezary Jackiewicz <cezary@eko.one.pl>

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-10 15:22:26 +02:00
DENG Qingfang
a30abb1b6b ipq40xx: add support for MobiPromo CM520-79F
MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019

Specification:

SoC/Wireless: QCA IPQ4019
RAM: 512MiB
Flash: 128MiB SLC NAND
Ethernet PHY: QCA8075
Ethernet ports: 1x WAN, 2x LAN
LEDs: 7 LEDs
      2 (USB, CAN) are GPIO
      other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register
Button: Reset

Flash instruction:
Disassemble the router, connect UART pins like this:
 GND TX    RX
  [x x . . x .]
  [. . . . . .]

(QCA8075 and IPQ4019 below)
Baud-rate: 115200

Set up TFTP server: IP 192.168.1.188/24
Power on the router and interrupt the booting with UART console
env backup (in case you want to go back to stock and need it there):
	printenv
	(Copy the output to somewhere save)
Set bootenv:
	setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs'
	setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1'
	setenv cm520_boot 'run set_ubi; run bootkernel'
	setenv bootcmd 'run cm520_boot'
	setenv bootargs
	saveenv
Boot initramfs from TFTP:
	tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb
	bootm
After initramfs image is booted, backup rootfs partition in case of reverting to stock image
	cat /dev/mtd12 > /tmp/mtd12.bin
Then fetch it via SCP

Upload nand-factory.ubi to /tmp via SCP, then run
	mtd erase rootfs
	mtd write /tmp/*nand-factory.ubi rootfs
	reboot

To revert to stock image, restore default bootenv in uboot UART console
	setenv bootcmd 'bootipq'
	printenv
use the saved dump you did back when you installed OpenWrt to verify that
there are no other differences from back in the day.
	saveenv
upload the backed up mtd12.bin and run
	tftpboot mtd12.bin
	nand erase 0xb80000 0x7480000
	nand write 0x84000000 0xb80000 0x7480000
The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead
In case of this, set it back to rootfs:
	cd /tmp
	cat /dev/mtd7 > mtd7.bin
	echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4
	for i in 28 48 68 108; do
		dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i
	done
	mtd write mtd7.bin BOOTCONFIG
	mtd write mtd7.bin BOOTCONFIG1

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[renamed volume to ubi to support autoboot,
as per David Lam's test in PR#2432]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-04-10 15:22:26 +02:00
Stefan Lippers-Hollmann
fabcfa9222 ipq40xx: re-add LEDS_LP5523 for the ASUS Lyra MAP-AC2200
This symbol had been enabled in the initial device support submission
for kernel 4.14, but apparently got lost during the v4.19 port.

The ASUS Lyra MAP-AC2200 has a single (very bright) rgb LED, which is
controlled by the TI/National LP5523/55231 LED driver chip. It is left
enabled in a pulsating infinite rainbow loop by the bootloader,
expecting it to be reconfigured (disabled by default) after the boot
process has finished and is also required to indicate failsafe/
firstboot conditions.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2020-04-09 12:51:10 +02:00
Petr Štetiar
5562c5add2 ipq40xx: fix DAP-2610 boot failure
Albert has reported, that his DAP-2610 wont boot with the latest
snapshot and Fredrik has found out, that the device gets stuck at
"Waiting for root device ..." due to missing 5.4 kernel config symbol
CONFIG_MTD_SPLIT_WRGG_FW which was probably lost during the kernel
version bump.

Ref: https://forum.openwrt.org/t/dap-2610-bricked-help-needed
Fixes: 272e0a702a ("ipq40xx: add v5.4 support")
Suggested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-31 16:20:47 +02:00
Petr Štetiar
bf15557f8a ipq40xx: switch to 5.4 kernel
5.4.24 seems to be working fine on my zyxel,nbg6617, so let's start
wider userbase testing.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Leon M. George
d59137d1d9 ipq40xx: wpj428: fix missing MDIO GPIO reset and pinmux
The bootloader does not always initialize the MDIO pins before booting
Linux. E.g. on version "U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Jul
25 2017 - 11:36:26)" this is the case when booting automatically without
activating the U-Boot console.

Without this change, the kernel boot will complain about missing PHYs:

 libphy: ipq40xx_mdio: probed
 ar40xx c000000.ess-switch: Probe failed - Missing PHYs!
 libphy: Fixed MDIO Bus: probed

With this change it will work as expected:

 libphy: ipq40xx_mdio: probed
 ESS reset ok!
 ESS reset ok!
 libphy: Fixed MDIO Bus: probed

Ref: GH-2835
Tested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit description from Fredrik, subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Sungbo Eo
3f14f034fb treewide: omit IMAGE_SIZE argument from check-size
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 20:02:55 +01:00
Sungbo Eo
5b392c7119 treewide: gather DEVICE_VARS into one place
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.

For ramips, remove redundant values already present in parent file.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 19:55:12 +01:00
Tomasz Maciej Nowak
ddc0e87fae kernel: move TEO governor to generic config
This new symbol popped up in few places. Disable it in generic config.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fixed merge conflict in generic/config-5.4]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-17 00:51:48 +01:00
Petr Štetiar
9ba09653ad treewide: remove maintainer variable from targets
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.

Lets make it clear, that it is solely a community doing the maintenance
tasks.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
2020-03-16 22:21:45 +01:00
Robert Marko
72c3997003 ipq40xx: 5.4: fix ethernet driver
In 5.4 kernel old u32 array way of setting network features was dropped and linkmode is now the only way.
So lets migrate the EDMA driver to support linkmode.
Also, old get/set settings API for ethtool is also dropped so lets convert to new ksettings API while at it as it demands linkmode.

Now, gigabit works properly as well as ethtool.
Previously you would get this in ethtool:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
        Supports Wake-on: d
        Wake-on: d
        Current message level: 0x00000000 (0)

        Link detected: yes

Now, features are properly advertised:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
                                             1000baseT/Full
        Link partner advertised pause frame use: No
        Link partner advertised auto-negotiation: No
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 4
        Transceiver: internal
        Auto-negotiation: on
        MDI-X: Unknown
        Supports Wake-on: d
        Wake-on: d
        Current message level: 0x00000000 (0)

        Link detected: yes

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-03-16 22:21:45 +01:00
Robert Marko
2b7344055b ipq40xx: 5.4: fix networking PHY driver
In 5.4 kernel old u32 array way of setting network features was dropped and linkmode is now the only way.
So lets migrate the PHY driver to support linkmode.
Also, now in order for gigabit to work, PHY driver needs to advertise PHY_GBIT_FEATURES instead of PHY_BASIC_FEATURES

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-03-16 22:21:45 +01:00
Petr Štetiar
f521ef5ff3 ipq40xx: 5.4: fix of_get_mac_address obsolete usage OOPs
of_get_mac_address returns valid pointer or ERR_PTR since 5.2 via commit
d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") so the
patch fixes following OOPs on nbg6617:

 Unable to handle kernel paging request at virtual address ffffffed
 CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.4.24 #0
 PC is at edma_axi_probe+0x444/0x1114
 LR is at bus_find_device+0x88/0x9c

Where the PC can be resolved to:

 >>> l *edma_axi_probe+0x444
 0xc067be5c is in edma_axi_probe (./include/linux/string.h:378).

 >>> l *edma_axi_probe+0x43f
 0xc067be57 is in edma_axi_probe (drivers/net/ethernet/qualcomm/essedma/edma_axi.c:936)

Which leads to the following code fragment:

 935  mac_addr = of_get_mac_address(pnp);
 936  if (mac_addr)
 937      memcpy(edma_netdev[idx_mac]->dev_addr, mac_addr, ETH_ALEN);

Where using mac_addr=0xffffffed (-ENODEV) as source address in memcpy()
is causing the OOPs.

Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-16 22:21:45 +01:00
Robert Marko
e09a5efcdb ipq40xx: 5.4: enable NAND
Lets enable RAW NAND and Qcom NANDC drivers again in kernel 5.4.
They were dropped when 5.4 support was introduced due to upstream
changing the symbol names so refreshing was not enough.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[cut long line in commit message, enabled BCH as well]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-03-15 15:26:34 +01:00
Robert Marko
3ef988caf3 generic: 4.19: Add 4B_OPCODES flag to w25q256
This patch backports the upstream patch that adds the 4B_OPCODES flag to w25q256 under 4.19 kernel.
This is needed for ipq40xx and ramips.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2020-03-12 12:59:44 +01:00
Hauke Mehrtens
988546cd13 ipq40xx: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-03-12 09:28:23 +01:00
Sungbo Eo
926f4da2b2 ipq40xx: replace ${} with $()
${} and $() are exactly the same. Follow the convention of using $().

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-03-11 19:24:37 +01:00
Leon M. George
377e8942b2 ipq40xx: add cpximg to flash Compex WPJ428 via bootloader
Generate a cpximg that is compatible with the cpximg loader in Compex' u-boot.
The cpximg loader can be started either by holding the reset button during power
up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept an image
appropriate for the board revision that is etched on the board (e.g. 6A04).

The image can be pushed using tftp:
  tftp -v -m binary 192.168.1.1 -c put openwrt-ipq40xx-generic-compex_wpj428-squashfs-cpximg-6a04.bin

cpximg files can also be used with the sysupgrade utility in stock images.
(add SSH key in luci for root access)

In mkmylofw_32m, the calculation of the "partition size" has been preferred
to just padding the partition as this will result in less block transfers
during flashing (while the additional complexity is bearable).

Signed-off-by: Leon M. George <leon@georgemail.eu>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-10 13:44:51 +01:00
Yousong Zhou
860652f4b9 kernel: 5.4: move some kconfig options to generic
CONFIG_64BIT_TIME=y
	CONFIG_KASAN_STACK=1
	CONFIG_UBSAN_ALIGNMENT=y
	CONFIG_UNIX_SCM=y
	CONFIG_DMA_DECLARE_COHERENT=y
	CONFIG_OF_RESERVED_MEM=y

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-03-10 10:05:50 +08:00
Koen Vandeputte
f9f62d43e4 kernel: bump 5.4 to 5.4.24
Refreshed all patches.

Compile-tested on: imx6
Runtime-tested on: imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-03-09 20:43:53 +01:00
Koen Vandeputte
e64564920a kernel: bump 4.19 to 4.19.108
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-03-09 20:43:53 +01:00
Koen Vandeputte
d5a3536631 kernel: bump 4.14 to 4.14.172
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-03-09 20:43:53 +01:00
Robert Marko
6256ca3232 ipq40xx: add support for 8devices Habanero DVK
This patch adds support for the 8devices Habanero development board.

Specs are:
CPU: QCA IPQ4019
RAM: DDR3L 512MB
Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without)
WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2
WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2
Ethernet: 5x Gbit LAN (QCA 8075)
USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019)
MicroSD slot (Uses SD controller built into IPQ4019)
SDIO3.0/EMMC slot (Uses the same SD controller)
Mini PCI-E Gen 2.0 slot (Built into IPQ4019)
5x LEDs (4 GPIO controllable)
2x Pushbutton (1 is connected to GPIO, other to SoC reset)
LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support)
1x UART 115200 rate on J18

2x breakout development headers
12V DC Jack for power
DIP switch for bootstrap configuration

Installation instructions:
Since boards ship with vendors fork of OpenWrt sysupgrade can be used.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2020-03-09 00:53:50 +01:00
Robert Marko
4ff6c43499 ipq40xx: add IPQ4019 SD/MMC controller support
This commit finally adds support for the built in SD/MMC controller in IPQ4019 SoC.

Controller is supported by the upstream SDHCI-MSM driver with a minor clock setting patch.
Patch is special to the IPQ4019 and cannot be upstreamed.

LDO and SDHCI node are upstreamed, and LDO node is awaiting to be accepted.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2020-03-09 00:53:50 +01:00
Adrian Schmutzler
74cbc44086 ipq40xx: fix support of EnGenius EAP2200
This fixes a typo in the device string for MAC address setup in
02_network and corrects the indent in the device's DTS files.

While at it, move the aliases section before the keys section to
have it closer to the top of the file.

Fixes: a736d912e2 ("ipq40xx: add support for EnGenius EAP2200")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-05 12:53:06 +01:00
David Bauer
0d727f231f treewide: move commonly disabled symbols to generic config
Move new commonly disabled kernel 5.4 symbols to the generic kernel
configuration.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-03-01 00:51:23 +01:00
Christian Lamparter
91a7c9c27d ipq40xx: 5.4: refresh patches and config
This patch just refreshes the 5.4 patches. It seems as if
070-v4.20-soc-qcom-spm-add-SCM-probe-dependency.patch is
already applied, so drop it. It also does a quick
make kernel_oldconfig to get rid of unneeded symbols.

[Looks like USB and Ethernet need some more work].

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-02-28 22:46:27 +01:00
Eneas U de Queiroz
13b8404b1e ipq40xx: qce - add fixes for AES ciphers
This backports commits from master that fix AES ciphers when using the
qce driver:

 - A couple of simple fixes for CTR and XTS modes used with AES:
   * 041-crypto-qce-fix-ctr-aes-qce-block-chunk-sizes.patch
   * 042-crypto-qce-fix-xts-aes-qce-key-sizes.patch

 - A fix for a bug that affected cases when there were more entries in
   the input sg list than necessary to actually encrypt, resulting in
   failure in gcm, where the authentication tag is present after the
   encryption data:
   * 043-crypto-qce-save-a-sg-table-slot-for-result-buf.patch

 - A fix to update the IV buffer passed to the driver from the kernel:
   * 044-crypto-qce-update-the-skcipher-IV.patch

 - A patch that reduces memory footprint and driver initialization by
   only initializing the fallback mechanism where it is actually used:
   * 046-crypto-qce-initialize-fallback-only-for-AES.patch

 - Three patches that make gcm and xts modes work with the qce driver,
   and improve performance with small blocks:
   * 047-crypto-qce-use-cryptlen-when-adding-extra-sgl.patch
   * 048-crypto-qce-use-AES-fallback-for-small-requests.patch
   * 049-crypto-qce-handle-AES-XTS-cases-that-qce-fails.patch

 - A patch that allows the hashes/ciphers to be built individually.
   * 051-crypto-qce-allow-building-only-hashes-ciphers.patch

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[renumbered patches, added patches from dropped commit, refreshed, 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-02-28 22:46:09 +01:00
Eneas U de Queiroz
ee4a0afdcd ipq40xx: use neon crypto drivers
This adds the neon based implementations of AES & SHA256.

For AES, according to the kernel config help:

Use a faster and more secure NEON based implementation of AES in CBC,
CTR and XTS modes.
Bit sliced AES gives around 45% speedup on Cortex-A15 for CTR mode
and for XTS mode encryption, CBC and XTS mode decryption speedup is
around 25%. (CBC encryption speed is not affected by this driver.)
This implementation does not rely on any lookup tables so it is
believed to be invulnerable to cache timing attacks.
...
The observed speedups on ipq40xx are more modest: speedup is around 20%
for CTR mode and for XTS mode encryption, CBC and XTS mode decryption
speedup is around 10%. Measurements were made using tcrypt, with
1024-bytes blocks for CTR & CBC, and 4096-bytes for XTS.
The aes-neon-bs driver uses a fallback for CBC encryption; that fallback
could be either the generic driver written in C, or the scalar arm-asm
one.  Even though aes-arm is 1.9% slower, it is more resilient to timing
attacks (the reason for being slower), so it is being included here.

The neon sha256 module increases performance over the generic module by
33%.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[Enable only ciphers for now, reorder patch in series to help bisect
as new symbols could lead to build failures, 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-02-28 22:46:09 +01:00
Eneas U de Queiroz
26681de412 ipq40xx: qce - switch to skcipher API
This backports a commit updating the API of the QCE crypto engine to
what is used in current kerenl, easing future upstream backports.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[renumber patches, refreshed, added 5.4 patches]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-02-28 22:46:01 +01:00