Use persistent MAC address for the built-in wireless interfaces of the
BPi-R64 and BPi-R3 development boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The type of those images is already distinguishable by the '.itb'
extension, there is no need for an additional '-fit' string in the
filenames. Remove it to behave more like other targets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Only on the ipq40xx subtarget different filenames were used for NAND-
based devices. This is unneeded, confusing and breaks downstream tools
such as luci-app-attendedsysupgrade and auc.
Remove the 'nand-' string from image filenames to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enabling both CONFIG_MMC_BCM2835 and CONFIG_MMC_BCM2835_SDHOST causes this
error in dmesg:
Error: Driver 'sdhost-bcm2835' is already registered, aborting...
Disabling CONFIG_MMC_BCM2835 and leaving CONFIG_MMC_BCM2835_SDHOST enabled
avoids this error.
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B
Signed-off-by: John Audia <therealgraysky@proton.me>
[Disable driver for all subtargets, refresh configs, tweak description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The CDMQ ingress special tag flag needs to be set for 7986 even without DSA
untag offload, otherwise tx checksum offload seems to break
Fixes: 9b482ee22f ("kernel: add more fixes for mtk_eth_soc")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Protect the flow block cb list readers against concurrent updates
Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When compiling OpenWRT on a compressed btrfs volume the build fails in
libtool.
The file `libltdl/config/ltmain.m4sh` from `libtool-2.4.2.tar.xz` is
missing write permissions, therefore patch falls back to copying the
file and patching that. During this patch tries to preserve all file
attribute on the new copy.
However the attribute `btrfs.compression` is privileged and btrfs return
EACCES.
While patch ignores multiple other error codes during the copy of xattr
copy it is not prepared for EACCES and aborts.
EACCES should be ignored the same way as the other errors.
Build log:
```
...
Applying ./patches/000-relocatable.patch using plaintext:
patching file libltdl/config/general.m4sh
patching file libtoolize.in
patching file libtoolize.m4sh
patching file libltdl/m4/libtool.m4
Applying ./patches/100-libdir-fixes.patch using plaintext:
patching file libltdl/config/ltmain.m4sh
File libltdl/config/ltmain.sh is read-only; trying to patch anyway
patching file libltdl/config/ltmain.sh
patch: setting attribute btrfs.compression for btrfs.compression: Permission denied
Patch failed! Please fix ./patches/100-libdir-fixes.patch!
```
Link: https://lists.gnu.org/archive/html/bug-patch/2022-11/msg00000.html
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
Keenetic KN-3010 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7621DAT.
Specification:
- System-On-Chip: MT7621DAT
- CPU/Speed: 880 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100/1000 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): MT7603E 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch
Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
wifi indicator.
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3010-squashfs-factory.bin"
to "KN-3010_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Intel PINCTRL is not enable in the 64bit build, while it is enabled in
the x86/general target, which disables the ability of controlling GPIO
in the 64 bit build.
This commit copies the corresponding part of x86/general config, since
it is already there, so it should be fine to enable the same settings
here.
Signed-off-by: Xiaopo Zhang <xiaopoz@proton.me>
On TP-Link TL-WR740N/TL-WR741ND v4 LAN MAC address (eth1 in DTS) is main
device MAC address, so do not increment it. WAN MAC is LAN MAC + 1.
Signed-off-by: Will Moss <willormos@gmail.com>
The downstream OpenWrt driver for the BCM53128 switch ceased to work,
rendering the 8 LAN ports of the device unusable. This commit disables
image building while the problem is being solved.
See issue #10374 for more details.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.
This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.
wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.
The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.
Test passed on my wndr3700v4 and wndr4500v3.
Signed-off-by: Edward Chow <equu@openmail.cc>
Performance comparison (iperf3, mtu 1500):
Before: 53.9 Mbps
After: 87.9 Mbps
The tests were performed on a BT Home Hub 5A router.
The iperf3 server was running on the router, the client
on the host.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Enabled CONFIG_MIPS_MT_SMP and CONFIG_SCHED_SMT.
Tested on FRITZ!Box 7330 SL, 7312 and o2 Box 4421.
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes leftover TODO from commit 6bf179b270
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Run of 'make kernel_oldconfig CONFIG_TARGET=subtarget'
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.
This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.
wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.
The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.
Test passed on my tplink tl-wdr4310.
Signed-off-by: Edward Chow <equu@openmail.cc>
The mt7623 subtarget supports 2 devices:
* Bananapi BPi-R2 (added in 1f068588ef, 7762c07c88),
* UniElec U7623-02 (added in 4def81f30f).
Both devices support DSA from the beginning, thus
swconfig can be safely disabled.
In the past, the subtarget mt7623 also supported
the mt7623 reference board. This board originally
supported swconfig, and was later converted to DSA
(64175ffb79) and then dropped (1ab81bf02d).
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
With this patch you can change the pulse digit time by loading the Lantiq
FXS driver kernel module called ltq-tapi. This is relevant for old
rotaryphones that uses pulsedialing.
The default values are:
30-80ms for the low pulse
30-80ms for the high pulse
300ms for minimum Interdigit time
this is OK but on some Phones it can be usefull to customize the values
If you want to change the values to high and low pulse to 40-90ms and
minimum interdigit time to 400ms
than change /etc/modules.d/20-ltq-tapi to (without linebrakes):
drv_tapi min_digit_low=40 min_digit_high=90 max_digit_low=40 \
max_digit_high=90 min_interdigit=400
Signed-off-by: Jonas Albrecht <plonkbong100@protonmail.com>
The symbolic link introduced in 22e9d8bc89 is wrong.
Fixes: 22e9d8bc89 ("cypress-firmware: use symlink to provide firmware in brcm")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Fix mmc_write_vol hush script used by many boards to avoid timeouts on
slow SD cards:
Instead of erasing a complete partition, only erase blocks for the
to-be-written image when writing to MMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
While compiling OpenWrt master for Turris 1.x routers (p2020), it
reported following error:
Gianfar Ethernet (GIANFAR) [Y/n/m/?] y
Freescale DPAA2 Ethernet Switch (FSL_DPAA2_SWITCH) [N/m/y/?] (NEW)
Error in reading or end of file.
Let's fix it by disabling it.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Since all NVRAM files in external repo are now upstreamed and to lower
future maintenance cost, disassociate the package from external source
repo.
All upstream pending NVRAM files shall be stored locally from now on.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[Remove outdated URL, add SPDX-License-Identifier]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Found during work on qoriq target.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[improve commit message, remove from target configs]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
use defaults if no build opts selected
(allows build with defaults when mbedtls not selected and configured)
Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
According to commit 6f6c2fb321, AP6335 module used in PICO-PI-IMX7D works
only with firmware from `linux-firmware`. However, firmware from
`cypress-firmware` suite is directly from the chip company (Infineon) and
is actually newer.
Instead of dropping the firmware from Infineon, create a package named
`brcmfmac-firmware-4339-sdio`, and keep the Infineon version of
`cypress-firmware-4339-sdio` around.
This gives us devs the option to choose. Also, it means that
- packages `brcmfmac-firmware-*` uniformly come from `linux-firmware`
- packages `cypress-firmware-*` uniformly come from `cypress-firmware`
so hopefully brings more clarity.
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Package `cypress-nvram` was added because back then the files for newer
RPi models on `linux-firmware` didn't have the proper values.
It is the other way around nowadays, so switch back to `linux-firmware`.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
This is to align the implementation with upstream `linux-firmware`.
Some Raspberry Pi boards do not have dedicated NVRAM in `linux-firmware`
source repository, their NVRAM is provided through a symbolic link to
NVRAM of another board with an identical wireless design.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
This is to align the implementation with upstream `linux-firmware`.
Instead of moving these firmware files to `brcm` subdirectory and changing
their names, leave them in `cypress` subdirectory, keep their names intact
and use symbolic links to provide compatibility with Broadcom FullMAC
driver.
This gives more context to where the firmware comes from.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
This is to align the implementation with upstream `linux-firmware`.
Some Raspberry Pi boards do not have dedicated NVRAM in `linux-firmware`
source repository, their NVRAM is provided through a symbolic link to
NVRAM of another board with an identical wireless design.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
PROVIDES for these packages will cause ambiguity and circular dependency
in planned changes.
For example, if there is a package `brcmfmac-firmware-43455-sdio-rpi-cm4`
that depends on `brcmfmac-firmware-43455-sdio-rpi-4b`, there is no way to
tell which one of below packages the system will go for.
- package named `brcmfmac-firmware-43455-sdio-rpi-4b`
- package named `cypress-nvram-43455-sdio-rpi-4b` that PROVIDES
`brcmfmac-firmware-43455-sdio-rpi-4b`
When ambiguity is unacceptable, PROVIDES (aliases) shall be removed and
packages shall only be used through their exact name.
So remove PROVIDES and keep only CONFLICTS.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Some copper SFP modules come with Marvell's 88E1xxx PHY and need this
module to function. Package it, so users can easily install this PHY
driver and use e.g. FINISAR CORP. FCLF-8521-3-HC SFP.
Without marvell PHY driver:
sfp sfp2: module FINISAR CORP. FCLF-8521-3-HC rev A sn XXXXXXX dc XXXXXX
mt7530 mdio-bus:1f sfp2: validation with support 0000000,00000000,00000000 failed: -22
sfp sfp2: sfp_add_phy failed: -22
With marvell PHY driver:
sfp sfp2: module FINISAR CORP. FCLF-8521-3-HC rev A sn XXXXXXX dc XXXXXX
mt7530 mdio-bus:1f sfp2: switched to inband/sgmii link mode
mt7530 mdio-bus:1f sfp2: PHY [i2c:sfp2:16] driver [Marvell 88E1111] (irq=POLL)
mt7530 mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
