The Compex WPQ873 is a development board with two M.2 B-key
slots for cellular modems.
Device info:
- IPQ8072A SoC
- 512MiB RAM
- 256MiB NAND flash
- 8MiB SPI NOR
- 3x 1GigE ports
- 1x 2.5GigE port
- 2.4GHz/5GHz AX WLAN
- 1x USB 3.0 port
- 1x M.2 B-key socket with PCIe 3.0
- 1x M.2 B-key socket with PCIe 2.0 and USB 3.0
- 4x SIM card slots
- Bluetooth LE 5.0 (QCA4024)
Prerequisites
1) TFTP server
2) 3.3V USB to TTL cable for UART console
2.54mm pitch 4-pin header for UART is readily provided on board, no modifications are necessary to access it
TTL connector pinout: 2=TX, 3=RX, 4=GND
Arrow marks pin 1 which is 3.3V
Serial port settings: 115200 8N1 no flow control
The device will most likely ship with a QSDK-based firmware.
1. Power on device and interrupt u-boot to obtain u-boot CLI
2. set serverip to IP address of the TFTP server, for example:
`setenv serverip 192.168.1.10`
3. Download image from TFTP server:
`tftpboot 0x44000000 openwrt-ipq807x-generic-compex_wpq873-squashfs-factory.ubi`
4. Flash ubi image to both partitions and reset:
`sf probe
imxtract 0x44000000 ubi
nand device 0
nand erase 0x0 0x3400000
nand erase 0x3c00000 0x3400000
nand write $fileaddr 0x0 $filesize
nand write $fileaddr 0x3c00000 $filesize
reset`
Afterwards, you can use sysupgrade to flash new OpenWRT images.
Signed-off-by: Antti Nykänen <antti.nykanen@nokia.com>
Replace the refreshed 5.15 backports with backports for 6.1.
This fixes FMODE_CAN_ODIRECT having the same value as
FMODE_NOREUSE.
Signed-off-by: Kazuki Hashimoto <kazukih0205@gmail.com>
Commit 1cb8cdb ("ci: use new buildbot worker images with Debian 11")
introduced new Git version with strict rules for owner of the git
directory.
To handle this and not cause major change, just move the parsing before
the change of ownership of the openwrt directory permitting the correct
run of git fetch command with the same user that did the repository
checkout.
Fixes: 1cb8cdb ("ci: use new buildbot worker images with Debian 11")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Commit bf8187d5dc ("CI: use split target and subtarget in label
workflow") didn't correctly output subtarget resulting in calling with
an empty subtarget. Fix this and correctly output generated subtarget.
Fixes: bf8187d5dc ("CI: use split target and subtarget in label workflow")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
With eecc6e4811 ("CI: rework build workflow to have split target and
subtarget directly") target and subtarget are split in 2 different
variables. Label workflow were not aligned to this change and are
currently broken.
Fix them and correctly pass split target and subtarget.
Fixes: eecc6e4811 ("CI: rework build workflow to have split target and subtarget directly")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Due to problem with migrating from master to main as the default branch
and downstream project still requiring the master branch to be present,
we currently have for push events double CI runs, one for main and one
for master. To solve this ignore any push event to the master branch for
every workflow that react on push events.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CONFIG_PAHOLE_HAS_SPLIT_BTF should be runtime detected as it depends on
pahole being available on the host, so filter it out of configs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is no reason for Octeon PCI endpoint driver to be disabled in targets
so disable it in generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is no reason for HP ProLiant HW watchdog to be disabled in individual
targets, so disable it in generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is no reason for CONFIG_ARCH_NXP to have to be disabled in individual
targets, so just disable CONFIG_ARCH_NXP in generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is no need for Surface platform drivers to be enabled by default,
especially on OpenWrt so disable CONFIG_SURFACE_PLATFORMS in the generic
config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
My original bpftools package made "variant" builds of bpftool and libbpf
as a convenience, since both used the same local kernel sources with the
same versioning. This is no longer the case, since the commit below
switched to using an out-of-tree build mirror hosting repos for each.
Replace bpftools with separate bpftool and libbpf packages, each simplified
and correctly versioned. Also fix the broken libbpf ABI introduced in the
same commit. Existing build .config files are not impacted.
Fixes: 00cbf6f6ab ("bpftools: update to standalone bpftools + libbpf, use the latest version")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
It's only used on devices in mt7621 and mt7622 subtargets, so no reason
to compile it for others.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
As of ed5c2f5fd10d ("i2c: Make remove callback return void") return
value of remove function is ignored.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Currently, SSDK is rather special in the sense that its not being built as
a proper out of tree module at all but rather like a userspace application
and that involves a lot of make magic which unfortunately broke with make
version 4.4 and newer.
Luckily QCA finally added a way to build SSDK as an out of tree module
and it uses the kernel buildsystem which makes it compile with make 4.4
as well.
So lets backport the support for it and switch to using it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support to use container included external toolchain and skip
redownloading external sdk for each test.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add checks to test if toolchain container can be used.
This is to handle case of new target or migration of any sort.
If the toolchain container can't be found, the tools container is used
instead.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add option to configure container to use for build test.
By default the tools container is used if no option is provided.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently all 23.05 related CI jobs are failing as the containers are
not available, so lets fix it by pushing those containers when the
version.mk changes.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tony has reported, that CI tools job is failing for him in macOS
container due to prereq check failure for GNU `install` utility.
Michael diagnosed it and from his traces it was clear, that the issue is
caused by a wrong return value in the success check case, so lets fix it
accordingly.
Fixes: f75204036c ("prereq-build: allow host command symlinks to update")
Reported-by: Tony Ambardar <itugrok@yahoo.com>
Diagnosed-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This add basic device tree support for mediatek MT7988 SoC
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Richtek RT5190A is used on the MT7988 reference board. Backport and
enable the driver on the filogic subtarget, so we can support cpufreq
on the MT7988 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add driver for the built-in 2.5G Ethernet PHY found in the MT7988 SoC.
To function the PHY also needs firmware files which have not yet been
published via linux-firmware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update driver for MediaTek's built-in Gigabit Ethernet PHYs which can be
found in the MT7981 and MT7988 SoCs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport commits adding support for the MT7988 built-in switch to the
mt7530 driver.
This change results in the Kconfig symbol NET_DSA_MT7530 to be extended
by NET_DSA_MT7530_MDIO (everything formally covered by NET_DSA_MT7530)
and NET_DSA_MT7530_MMIO (a new driver for the MMIO-connected built-in
switch of the MT7988 SoC).
Select NET_DSA_MT7530_MDIO for all targets previously selecting
NET_DSA_MT7530, with the exception of mediatek/filogic which also
selects NET_DSA_MT7530_MMIO.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to support Ethernet on the MT7988 SoC add support for NETSYS v3
as well as new paths and USXGMII SerDes to the mtk_eth_soc driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds provisional pinctrl driver support for the MediaTek MT7988 SoC.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds clock drivers for the MediaTek MT7988 SoC
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows loading modules with large memory requirements, recently needed
while testing on armvirt/32. Past forum discussions [1] and bug reports [2]
also raised this and the ipq806x target already set it in response [3].
Given this increases kernel image size by only ~1KB, is generally useful on
multi-platform kernels, and enabled by default on upstream arm32 Linux, add
it to the generic config.
The setting has similar utility on arm64, is a requirement for KASLR, and
already enabled on most OpenWrt aarch64 targets, so pull this into the
top-level generic config.
[1]: https://forum.openwrt.org/t/vmap-allocation-for-size-442368-failed-use-vmalloc-size-to-increase-size/34545/7
[2]: https://github.com/openwrt/openwrt/issues/8282
[3]: f81e148eb6 ("ipq806x: update 4.19 kernel config").
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This partially reverts commit 7fae1e5677
as it should be no longer necessary to do a full clone since commit
48ed07bc0b ("treewide: replace AUTORELEASE with real PKG_RELEASE").
Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The identical change was previously added to the 5.15 kernel in the commit
9226f1e419 ("kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic config").
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Kernel 6.1 now has fortify_memcpy_chk() and it is causing the following
warning while trying to compile backports:
CC [M] /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/net/wireless/util.o
In file included from ./include/linux/string.h:253,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/string.h:3,
from ./include/linux/bitmap.h:11,
from ./include/linux/cpumask.h:12,
from ./include/linux/smp.h:13,
from ./arch/arm64/include/asm/arch_timer.h:18,
from ./arch/arm64/include/asm/timex.h:8,
from ./include/linux/timex.h:67,
from ./include/linux/time32.h:13,
from ./include/linux/time.h:60,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/time.h:3,
from ./include/linux/skbuff.h:15,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/etherdevice.h:3,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/net/wireless/util.c:12:
In function 'fortify_memcpy_chk',
inlined from 'ieee80211_strip_8023_mesh_hdr' at /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/net/wireless/util.c:590:3:
./include/linux/fortify-string.h:404:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
404 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
This issue was fixed in the final version of
("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces") that was
merged upstream but we have a older version that is using:
memcpy(&payload.eth.h_dest, mesh_addr, 2 * ETH_ALEN);
instead of:
memcpy(&payload.eth, mesh_addr, 2 * ETH_ALEN);
So, lets just backport the merged version of patch to fix the issue.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allow building SD card images without having both initramfs and squashfs
present on the card, just like it has already been done for the mt7622
and filogic subtargets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
