31e99fe3da which introduced this code was unfortunately untested.
This commit fixes a number of issues and works around the fact that in
this particular scheme, the LZO payload may be padded at the end which
will trigger a harmless lzo decompression error.
This commit also disambiguates the debug printks.
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 31e99fe3da ("generic: platform/mikrotik: support LZOR encoding")
An e-mail response from MikroTik contained a minimal overview
on hardware option bits which mentioned a currently unknown bit.
While not being too detailed what it does, add it for documentation purposes.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Fixes a build error seen when applying the kernel patches.
Applying patch generic/435-mtd-add-routerbootpart-parser-config.patch
patching file drivers/mtd/parsers/Kconfig
Hunk #1 FAILED at 160.
1 out of 1 hunk FAILED -- rejects in file drivers/mtd/parsers/Kconfig
patching file drivers/mtd/parsers/Makefile
Hunk #1 FAILED at 10.
1 out of 1 hunk FAILED -- rejects in file drivers/mtd/parsers/Makefile
This was missed as 5.4 is currently set as testing kernel
while the main kernel being used is 4.19
Fixes: 2976e423dc ("generic: routerboot partition build bits")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Some newer MikroTik RouterBOARD devices use a new encoding scheme
for their WLAN calibration data. This patch provides support for
decoding this new scheme.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This driver exposes the data encoded in the "hard_config" flash segment
of MikroTik RouterBOARDs devices. It presents the data in a sysfs folder
named "hard_config". The WLAN calibration data is available on demand via
the 'wlan_data' sysfs file in that folder.
This driver permanently allocates a chunk of RAM as large as the
"hard_config" MTD partition (typically 4KB), although it is technically
possible to operate entirely from the MTD device without using a local
buffer (except when requesting WLAN calibration data), at the cost of a
performance penalty.
This driver does not reuse any of the existing code previously found in
routerboot.c.
This driver has been successfully tested on BE (ath79) and LE (ipq40xx
and ramips) hardware.
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Tested-by: Baptiste Jonglez <git@bitsofnetworks.org>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This driver provides an OF MTD parser to properly assign the RouterBoot
partitions on the flash. This parser builds from the "fixed-partitions"
one (see ofpart.c), but it can handle dynamic partitions as found on
routerboot devices.
The parent node must contain the following:
compatible = "mikrotik,routerboot-partitions";
#address-cells = <1>;
#size-cells = <1>;
Children routerbootpart DTS nodes are defined as follows:
For fixed partitions
node-name@unit-address {
reg = <prop-encoded-array>;
label = <string>;
read-only;
lock;
};
All properties but reg are optional.
For dynamic partitions:
node-name {
size = <prop-encoded-array>;
label = <string>;
read-only;
lock;
};
size property is mandatory unless the next partition is a fixed one or
a "well-known" one (matched from the strings defined below) in which case
it can be omitted or set to 0; other properties are optional.
By default dynamic partitions are appended after the preceding one, except
for "well-known" ones which are automatically located on flash.
Well-known partitions (matched via label or node-name):
- "hard_config"
- "soft_config"
- "dtb_config"
This parser requires the DTS to list partitions in ascending order as
expected on the MTD device.
This parser has been successfully tested on BE (ath79) and LE (ipq40xx
and ramips) hardware.
Tested-by: Baptiste Jonglez <git@bitsofnetworks.org>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
ar8229 and ar8236 don't allow unknown unicast/multicast frames and
broadcast frames to be flooded to cpu port. This isn't desired behavior
for swconfig as we treat it as a standalone switch.
Current code doesn't enable unicast frame flooding for ar8229 and uses
wrong setup for ar8236. This commit fixes both of them by enabling port
0 flooding for all unknown frames.
Fixes: FS#2848
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Upstream commit dda9f4b9ca ("f2fs: fix to skip verifying block address
for non-regular inode").
On 4.14, attempting to perform operations on a non-regular inode
residing on an f2fs filesystem, such rm-ing a device node, would fail
and lead to a warning / call trace in dmesg. This fix was already
applied to other kernels upstream - including 4.19, from which the patch
was taken.
More info at https://bugzilla.kernel.org/show_bug.cgi?id=202495.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
This patch is needed for clause 37 1000Base-X encoding used in many SFP modules.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: René van Dorst <opensource@vdorst.com>
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Based on this, the selection of myloader.o in OpenWrt
was also moved to that subdirectory, while the Kconfig and our local
myloader.c file remained in /drivers/mtd.
This resulted in linking errors like the following (on ath25@5.4):
make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ...
needed by 'drivers/mtd/parsers/built-in.a'. Stop.
make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2
make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2
Since myloader.c is not too big, this patch moves it to the kernel patches,
allowing to adjust the path for kernel 5.4 and keeping Makefiles and
file paths better in sync.
Other patches have been refreshed accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There are 2 different chips (w25q256fv and w25q256jv) that share
the same JEDEC ID. Only w25q256jv fully supports 4-byte opcodes.
Use SFDP header version to differentiate between them.
Fixes broken reboot on 8devices Habanero since f0f35fdac
Signed-off-by: Mantas Pucka <mantas@8devices.com>
From kernel 4.20 msm-gpio driver is broken and cause the
malfunction of the buttons on every ipq806x target.
Add a patch to fix this.
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Instead of resetting flash to 3B address on remove hook, this
implementation only enters 4B mode when needed, which prevents more
unexpected reboot stuck. This implementation makes it only break when
a kernel panic happens during flash operation on 16M+ areas.
Also silent broken-flash-reset warning. We are not dealing with vendors
and it's unpleasant for users to see that unnecessary and long WARN_ON
print.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The conditional check introduced by this patch may trigger a NULL pointer
dereference in case the result of dev_net() is NULL.
Since the purpose of this patch is neither sufficiently explained and since
this patch apparently has never been submitted upstream despite it being in
the pending-* patch directory, I propose to drop it without replacement.
If the performance implications of dropping this patch are found to be
significiant, it should be reintroduced with proper description and
benchmark results.
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2943
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixing a build error when CONFIG_KERNEL_KEXEC is enabled:
make[5]: Entering directory '/home/bjorn/tmp/tmp-lede/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7621/linux-5.4.28'
CALL scripts/checksyscalls.sh
CALL scripts/atomic/check-atomics.sh
CHK include/generated/compile.h
CC arch/mips/kernel/machine_kexec.o
arch/mips/kernel/machine_kexec.c: In function 'kexec_nonboot_cpu_jump':
arch/mips/kernel/machine_kexec.c:268:27: error: 'relocate_new_kernel_size' undeclared (first use in this function); did you mean 'kexec_relocate_new_kernel_end'?
reboot_code_buffer + relocate_new_kernel_size);
^~~~~~~~~~~~~~~~~~~~~~~~
kexec_relocate_new_kernel_end
arch/mips/kernel/machine_kexec.c:268:27: note: each undeclared identifier is reported only once for each function it appears in
arch/mips/kernel/machine_kexec.c: In function 'kexec_reboot':
arch/mips/kernel/machine_kexec.c:306:27: error: 'relocate_new_kernel_size' undeclared (first use in this function); did you mean 'kexec_relocate_new_kernel_end'?
reboot_code_buffer + relocate_new_kernel_size);
^~~~~~~~~~~~~~~~~~~~~~~~
kexec_relocate_new_kernel_end
make[7]: *** [scripts/Makefile.build:266: arch/mips/kernel/machine_kexec.o] Error 1
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Backport patches which adds suport for the Wistron Neweb D19Q1 3G/4G modem,
used in D-Link DWR-960.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This reverts commit d7f21940bc.
Winbond W25Q256FV and W25Q256JV both uses 0xef4019 as JEDEC ID,
but only the latter has proper 4B_OPCODES support.
W25Q256FV has all 4B read instructions but it lacks a 4B page program
instruction, causing the entire flash to be read-only.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
In RTL8367B (RTL8367RB/RTL8367R-VB), the driver in GPL tars of the
devices with this switch directly uses the ID of external interface
as a bit offset.
We should use the same way.
ref (RTL8367B):
- ASUS RT-N56U
- TP-Link Archer C2 v1
ref (RTL8367):
- TP-Link TL-WR2543ND v1
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The 2nd gmac of mediatek soc ethernet may not be connected to a PHY
and a phy-handle isn't always available.
Unfortunately, mt7530 dsa driver assumes that the 2nd gmac is always
connected to switch port 5 and setup mt7530 according to phy address
of 2nd gmac node, causing null pointer dereferencing when phy-handle
isn't defined in dts.
This commit fix this setup code by checking return value of
of_parse_phandle before using it.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Use in tree version of cake for kernels 4.19+ and backport features from
later kernel versions to 4.19.
Unfortunately PROVIDES dependency handling produces bogus circular
dependency warnings so whilst this package and kmod-sched-cake-oot
should be able to PROVIDE kmod-sched-cake this doesn't work.
Instead, remove the PROVIDES option and modify package sqm-scripts to
depend on the correct module independently.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Enable kernel symbol CONFIG_RTC_DRV_CMOS which was enabled in 4.14 &
4.19
Fixes FS#2905 and now my APU2 picks up time from RTC
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Most targets upstream use 250Hz or even 1000Hz by default while
100Hz is hardcoded in OpenWrt's default config. Use upstream default
except for apm821xx which hardsets 1000Hz instead of platform default of
250Hz.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[Apply same changes to 5.4]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch updates arc-specific patch by moving declaration
of struct object before it's usage.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Petr Štetiar <ynezz@true.cz>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
These have been discovered by the gemini 5.4 patches.
This is because one of the devices uses the FBDEV emulation.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch backports the hwmon drivetemp sensor module from vanilla
linux 5.5 to be available on OpenWrt's 5.4 kernel.
Extract from The upstream commit by Guenter Roeck <linux@roeck-us.net>:
hwmon: Driver for disk and solid state drives with temperature sensors
"Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.
This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.
With this driver, the hard disk temperature can be read [...]
using sysfs:
$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000
If the drive supports SCT transport and reports temperature limits,
those are reported as well.
drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1: +27.0<C2><B0>C (low = +0.0<C2><B0>C, high = +60.0<C2><B0>C)
(crit low = -41.0<C2><B0>C, crit = +85.0<C2><B0>C)
(lowest = +23.0<C2><B0>C, highest = +34.0<C2><B0>C)
The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism."
This patch incorperates a patch made by Linus Walleij:
820-libata-Assign-OF-node-to-the-SCSI-device.patch
This patch is necessary in order to wire-up the drivetemp
sensor into the device tree's thermal-zones.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Fix header change that was done for kernel but 4.19 got missed for 5.4.
Solves nasty errors like:
8.4.0_musl/include/linux/netfilter/xt_CONNMARK.h:5,
from connmark_listener.c:30:
/builder/shared-workdir/build/sdk/staging_dir/toolchain-aarch64_cortex-a53_gcc-8.4.0_musl/include/linux/netfilter/xt_connmark.h:23:2: error: enumerator value for 'XT_CONNMARK_VALUE' is not an integer constant
XT_CONNMARK_VALUE = BIT(0),
^~~~~~~~~~~~~~~~~
/builder/shared-workdir/build/sdk/staging_dir/toolchain-aarch64_cortex-a53_gcc-8.4.0_musl/include/linux/netfilter/xt_connmark.h:25:1: error: enumerator value for 'XT_CONNMARK_DSCP' is not an integer constant
};
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This commit adds definition of DEBUG0 and DEBUG1 registers and replace
magic values with proper register modifying.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This new symbol popped up in few places. Disable it in generic config.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fixed merge conflict in generic/config-5.4]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Switch to the mainline Lantiq PCIe PHY driver and update the vr9.dtsi
accordingly.
The Lantiq IRQ SMP support added upstream required changes to the SoC
dtsi as well.
Following changes are made to the Lantiq kernel patches:
0005-lantiq_etop-pass-struct-device-to-DMA-API-functions.patch
0006-MIPS-lantiq-pass-struct-device-to-DMA-API-functions.patch
applied upstream
0008-MIPS-lantiq-backport-old-timer-code.patch
access_ok API update because it lost it's type (which was the first)
parameter in upstream commit 96d4f267e40f95 ("Remove 'type' argument
from access_ok() function")
0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch
merged into 0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
revert upstream changes required for upstream xrx200 ethernet and
xrx200 (DSA) switch driver but breaking our driver
0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
required for our driver but dropped upstream, add former upstream
version
0028-NET-lantiq-various-etop-fixes.patch
now has to use the phy_set_max_speed API instead of modifying
phydev->supported. Also call ltq_dma_enable_irq() in
ltq_etop_open() based on upstream commit cc973aecf0b054 ("MIPS:
lantiq: Do not enable IRQs in dma open")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
It adjusts the code to upstream changes from the commit 3c1bcc8614db
("net: ethernet: Convert phydev advertize and supported from u32 to link
mode")
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds a few symbols that I found that
need disabling in order to not break the build of octeontx
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This patch backports the upstream patch that adds the 4B_OPCODES flag to w25q256 under 5.4 kernel.
This is needed for ipq40xx and ramips.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch backports the upstream patch that adds the 4B_OPCODES flag to w25q256 under 4.19 kernel.
This is needed for ipq40xx and ramips.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit finally adds support for the built in SD/MMC controller in IPQ4019 SoC.
Controller is supported by the upstream SDHCI-MSM driver with a minor clock setting patch.
Patch is special to the IPQ4019 and cannot be upstreamed.
LDO and SDHCI node are upstreamed, and LDO node is awaiting to be accepted.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adds into 4.19 backported kernel module from 5.1 for Sensirion SPS30
particulate matter sensor, for kernel 5.4 backported dependency fix.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 15a0701cdd.
It was reported that this patch breaks on some cases the JFFS2 overlay
filesystem on targets still using kernel 4.14. This includes ar71xx,
where spurious erase of the ART was reported.
Revert this commit for now. Re-adding should probaby also be done for
every currently supported kernel version.
Ref: FS#2837 FS#2862 FS#2864
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport kernel module from 5.5 for FXOS8700CQ, which is a small,
low-power, 3-axis linear accelerometer and 3-axis magnetometer combined
into a single package. The device features a selectable I2C or
point-to-point SPI serial interface with 14-bit accelerometer and 16-bit
magnetometer ADC resolution along with smart-embedded functions.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[added commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes the following warning for ARM targets:
WARNING: "return_address" [vmlinux] is a static EXPORT_SYMBOL_GPL
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch adds a few more symbols that I found that
need disabling in order to not break the automatic build.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch disables the CRYPTO KERNEL SYMBOLs that are touched
by the upcoming ipq40xx patch "ipq40xx: use neon crypto drivers"
from "Eneas U de Queiroz" and more so for his follow up patches
for the other ARM targets in this series. This should help to
prevent at least a few potential build errors on other archs.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Fix typedef clash on darwin.
HOSTCC scripts/mod/file2alias.o
scripts/mod/file2alias.c:47:3: error: typedef redefinition with different types ('struct uuid_t' vs '__darwin_uuid_t' (aka 'unsigned char [16]'))
} uuid_t;
^
/Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX.sdk/usr/include/sys/_types/_uuid_t.h:31:25: note: previous definition is here
typedef __darwin_uuid_t uuid_t;
^
scripts/mod/file2alias.c:1305:42: error: array initializer must be an initializer list or string literal
DEF_FIELD(symval, tee_client_device_id, uuid);
^
2 errors generated.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The nvmem framework is now used in net/ethernet/eth.c and the nvmem
sysfs is split into a separate Kconfig option. More work would be needed
to adapt this patch for the broader use. The current patch compiles fine
on ath79, but it breaks the x86 target.
nvmem is also compiled into the kernel for most of our targets for
example ath79 anyway, so patching the kernel to remove it is now harder
and not the case on multiple targets anyway. Instead of making this work
on kernel 5.4 just remove this hack patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes it possible to select CONFIG_CRYPTO_LIB_ARC4 directly. We
need this to be able to compile this into the kernel and make use of it
from mac80211 backports.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following patches were removed because they are integrated in the upstream kernel 5.4:
* backport-5.4/047-v4.21-mtd-keep-original-flags-for-every-struct-mtd_info.patch
* backport-5.4/048-v4.21-mtd-improve-calculating-partition-boundaries-when-ch.patch
* backport-5.4/080-v5.1-0001-bcma-keep-a-direct-pointer-to-the-struct-device.patch
* backport-5.4/080-v5.1-0002-bcma-use-dev_-printing-functions.patch
* backport-5.4/095-Allow-class-e-address-assignment-via-ifconfig-ioctl.patch
* backport-5.4/101-arm-cns3xxx-use-actual-size-reads-for-PCIe.patch
* backport-5.4/200-v5.2-usb-dwc2-Set-lpm-mode-parameters-depend-on-HW-configuration.patch
* backport-5.4/210-arm64-sve-Disentangle-uapi-asm-ptrace.h-from-uapi-as.patch
* backport-5.4/380-v5.3-net-sched-Introduce-act_ctinfo-action.patch
* backport-5.4/450-v5.0-mtd-spinand-winbond-Add-support-for-W25N01GV.patch
* backport-5.4/451-v5.0-mtd-spinand-Add-initial-support-for-Toshiba-TC58CVG2.patch
* backport-5.4/452-v5.0-mtd-spinand-add-support-for-GigaDevice-GD5FxGQ4xA.patch
* backport-5.4/455-v5.1-mtd-spinand-Add-support-for-all-Toshiba-Memory-produ.patch
* backport-5.4/456-v5.1-mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UExxG.patch
* backport-5.4/460-v5.0-mtd-spi-nor-Add-support-for-mx25u12835f.patch
* backport-5.4/460-v5.3-mtd-spinand-Define-macros-for-page-read-ops-with-thr.patch
* backport-5.4/461-v5.3-mtd-spinand-Add-support-for-two-byte-device-IDs.patch
* backport-5.4/462-v5.3-mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UFxxG.patch
* backport-5.4/463-v5.3-mtd-spinand-Add-initial-support-for-Paragon-PN26G0xA.patch
* backport-5.4/700-v5.1-net-phylink-only-call-mac_config-during-resolve-when.patch
* backport-5.4/701-v5.2-net-phylink-ensure-inband-AN-works-correctly.patch
* backport-5.4/702-v4.20-net-ethernet-Add-helper-for-MACs-which-support-asym-.patch
* backport-5.4/703-v4.20-net-ethernet-Add-helper-for-set_pauseparam-for-Asym-.patch
* backport-5.4/704-v4.20-net-phy-Stop-with-excessive-soft-reset.patch
* backport-5.4/705-v5.1-net-phy-provide-full-set-of-accessor-functions-to-MM.patch
* backport-5.4/706-v5.1-net-phy-add-register-modifying-helpers-returning-1-o.patch
* backport-5.4/707-v5.1-net-phy-add-genphy_c45_check_and_restart_aneg.patch
* backport-5.4/708-v5.3-net-phylink-remove-netdev-from-phylink-mii-ioctl-emu.patch
* backport-5.4/709-v5.3-net-phylink-support-for-link-gpio-interrupt.patch
* backport-5.4/710-v5.3-net-phy-allow-Clause-45-access-via-mii-ioctl.patch
* backport-5.4/711-v5.3-net-sfp-add-mandatory-attach-detach-methods-for-sfp-.patch
* backport-5.4/712-v5.3-net-sfp-remove-sfp-bus-use-of-netdevs.patch
* backport-5.4/713-v5.2-net-phylink-avoid-reducing-support-mask.patch
* backport-5.4/714-v5.3-net-sfp-Stop-SFP-polling-and-interrupt-handling-duri.patch
* backport-5.4/715-v5.3-net-phylink-don-t-start-and-stop-SGMII-PHYs-in-SFP-m.patch
* backport-5.4/740-v5.5-net-phy-avoid-matching-all-ones-clause-45-PHY-IDs.patch
* backport-5.4/741-v5.5-net-phylink-fix-link-mode-modification-in-PHY-mode.patch
* pending-5.4/103-MIPS-perf-ath79-Fix-perfcount-IRQ-assignment.patch
* pending-5.4/131-spi-use-gpio_set_value_cansleep-for-setting-chipsele.patch
* pending-5.4/132-spi-spi-gpio-fix-crash-when-num-chipselects-is-0.patch
* pending-5.4/220-optimize_inlining.patch
* pending-5.4/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch
* pending-5.4/475-mtd-spi-nor-Add-Winbond-w25q128jv-support.patch
* pending-5.4/477-mtd-add-spi-nor-add-mx25u3235f.patch
* pending-5.4/479-mtd-spi-nor-add-eon-en25qh64.patch
Some bigger changes were done to this feature and we did not port this patch yet:
* hack-5.4/207-disable-modorder.patch
This depends on BOOTMEM which was removed from the kernel, this needs some bigger changes:
* hack-5.4/930-crashlog.patch
A different version of the FPU disable patch was merged upstream, OpenWrt needs some adaptations.
* pending-5.4/304-mips_disable_fpu.patch
- no crashlog support yet as a required file got deleted upstream
- Removed patch below, which is now seen as a recursive dependency [1]
- Removed patch below due to build error [2]
- fix still required to avoid identical function def [3]
- Fixes included from Blocktrron
- Fixes included from Chunkeey
- Fix included from nbd regarding "dst leak in Flow Offload"
[1] target/linux/generic/hack-5.4/260-crypto_test_dependencies.patch
[2] target/linux/generic/hack-5.4/207-disable-modorder.patch
[3] target/linux/generic/pending-5.4/613-netfilter_optional_tcp_window_check.patch
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No changes were done to the patches while coping them. Currently they do
not apply on top of kernel 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make it possible to activate some additional kernel debug options.
This can be used to debug some problems in kernel drivers.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The kernel kernel address sanitizer is able to detect some memory
bugs in the kernel like out of range array accesses.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The kernel Undefined Behavior Sanitizer is able to detect some memory
bugs in the kernel like out of range array accesses.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Since kernel 5.2 within netlink messages the NLA_F_NESTED nested flag is
validated. But swconfig/swlib doesn't set the flag for
SWITCH_ATTR_OP_VALUE_PORTS related netlink messages and assigning ports
to vlans via
swconfig dev switch0 vlan 1 set ports '0 1 2 3 4 6t'
Errors put with "Failed to set attribute: Invalid input data or
parameter".
Relax the validation rules and use the deprecated functions, to use the
same level of validation as it was till kernel 5.1. Depending on who has
swconfig related netlink messages implemented, there might be more
broken tools out there and we should keep backward compatibility if
possible.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Make run_parsers_by_type() more similar to the parse_mtd_partitions():
1. Use struct mtd_partitions
2. Use add_mtd_partitions()
This change simplifies run_parsers_by_type() by:
1. Dropping loop
2. Dropping code getting partition properties (name, offset, size)
Moreover this change allows passing more partitions details (e.g.
mask_flags).
One noticeable change introduced by this patch is adding parsed
partitions as children. This results in printing their *relative*
offsets which unifies this code with parse_mtd_partitions() behaviour.
Before:
[ 1.785448] 0x00000018f800-0x000000fb0000 : "rootfs"
[ 1.791642] mtd: device 4 (rootfs) set to be root filesystem
[ 1.797537] 1 squashfs-split partitions found on MTD device rootfs
[ 1.804009] 0x0000004e0000-0x000000fb0000 : "rootfs_data"
After:
[ 1.785376] 0x00000018f800-0x000000fb0000 : "rootfs"
[ 1.791601] mtd: device 4 (rootfs) set to be root filesystem
[ 1.797491] 1 squashfs-split partitions found on MTD device rootfs
[ 1.803936] Creating 1 MTD partitions on "rootfs":
[ 1.808910] 0x000000350800-0x000000e20800 : "rootfs_data"
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
XTX XT25F128A shares it's chip ID with XM25QH128A which got identical
features. Hence there it makes no sense to add it to the driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
I'm having another attempt at trying to getting the 'store dscp into
conntrack connmark' functionality into upstream kernel, since the
restore function (act_ctinfo) has been accepted.
The syntax has changed from 'savedscp' to 'set-dscpmark' since that
conforms more closely with existing functionality.
4.14 backport is more of a hack since the structure versioning
mechanism isn't in place.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This fixes support for Teltonika RUT9xx which in recent versions of
the device uses xt25f128b flash.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
- Remove the "RGMII TX delay fixup" hack and the associated
DT-property. It was never used in a DT-based platform and
solved a problem which can be mitigated by using correct
delays on the MAC side.
- Remove the patch to enable platform-data support for the
at803x driver. It was only used by ar71xx which does not
(and never will) support kernel 4.19 or later.
- Remove the SmartEEE DT-configuration patch. As explained
previously, this patch never disabled the Atheros SmartEEE
implementation, but rather "standard" EEE. This can be done
on device-tree compatible platforms by adding the
"eee-broken-1000t" or "eee-broken-100tx" properties to the PHY
node. As all usages of the old properties are migrated, this
patch can be removed.
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Add patches retrying to probe the PHY to restore support for PHYs taking
longer to initialize without breaking modules without PHYs.
Patches taken from http://git.armlinux.org.uk/cgit/linux-arm.git/log/?h=phy
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for Methode DM7052 NBASE-T module to OpenWRT. These
patches are taken from my "phy" branch, and will be sent for the
next kernel merge window.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: move patches to pending, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Backport the phy/phylink/sfp patches currently queued in netdev or in
mainline necessary to support GPON popular modules, specifically to
support Huawei and Nokia GPON modules.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: include kernel version in file names, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Move two phylink patches from mvebu to generic, so that everyone can
benefit from them.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: add kernel version to file names]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This reverts commit de80424f70 which needs
more work and testing as it broke at least jffs2 overlays at least on
ath79 platform, marking them as read-only, thus unusable:
jffs2_build_filesystem(): erasing all blocks after the end marker...
jffs2: Erase at 0x009e0000 failed immediately: -EROFS. Is the sector locked?
Ref: http://lists.infradead.org/pipermail/openwrt-devel/2020-January/021344.html
Reported-by: Steve Brown <sbrown@ewol.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently it's not possible to effectively mark a "firmware" partition
as read-only. The sub-partitions "kernel", "rootfs" and "rootfs_data"
are always created as read-write (ignoring the parent access mode).
This patch enforces the access mode of sub-partitions to match the
parent partition, which is useful for recovery images that are meant
to be fully read-only to avoid accidental damage from end-user.
An example of such implementation (read-only firmware image) is the
recovery image used on the Zsun-SD100 [1].
Please note the related patch for fstools [2] to enable this read-only
concept.
[1] https://github.com/brunompena/zsun-resources
[2] http://lists.infradead.org/pipermail/openwrt-devel/2020-January/021043.html
Signed-off-by: Bruno Pena <brunompena@gmail.com>
[removed already obsolete 4.9 kernel patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Builds for kenrel 4.14 targetswere failing because of
missing symbols for the B53 swconfig driver.
Fixes: 313bde53ce ("generic: update config-4.19")
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit fixes a bug in the main swconfig patch where a function
needed by the b53 driver is not exported.
Additionally it adds OF support to the b53_mdio driver for devicetree-
based probing
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
330-MIPS-kexec-Accept-command-line-parameters-from-users.patch causes
problems when building with -Werror=unused-result.
arch/mips/kernel/machine_kexec.c: In function 'machine_kexec_init_argv':
arch/mips/kernel/machine_kexec.c:76:2: error: ignoring return value of 'copy_from_user', declared with attribute warn_unused_result [-Werror=unused-result]
copy_from_user(kexec_argv_buf, buf, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fix this by handling the return value in an appropriate way.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Physically allocated memory for modules needs to be registered with kmemleak,
so it can track it as object.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Deactivate CONFIG_SFP for kernel 4.19 in the generic configuration.
The CONFIG_SFP configuration option was not set to anything in the
ath79 build for me, set it to deactivated by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
PCI_V3_SEMI config symbol was found missing in generic kernel config
after ipq806x config refresh to 4.19.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It turns out my 4.14 testing had a rather large flaw in it and the
'extack' mechanism isn't quite ready. Remove the extack stuff from this
backport.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Since the original backports from kernel 5.3 a few things have been
tweaked by kernel bumps & other upstream changes. Update the backport
to reflect upstream as closely as possible and remove the bitrot.
Functions remain the same, error reporting improved.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The Atheros AR8327 and AR8337 have (according to their datasheet) a
VLAN table with a maximum of 4096 entries.
Currently, there's a hard limit of 128 VLANs, which is the same as
for most other Atheros switches. Increase this limit only for the
AR83x7 series and modify some shared functions to allow them to work
with a variable max VLAN count.
Signed-off-by: David Bauer <mail@david-bauer.net>
The Owl Loader (named after the codename that Atheros gave
these devices back in the day) has been accepted upstream.
This patch removes the "misc" driver OpenWrt had and adds
the remaining differences against the version that ships
with 5.4-rc1 into a separate "120-owl-loader-compat.patch"
file that can be cut down once AR71XX is being dealt with.
Note: I decided to keep the existing (kmod-)owl-loader
package name around for now. The kernel module file in
the kmod package will be called ath9k_pci_owl_loader.ko
though.
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Remove CC_HAS_ASM_GOTO, CC_IS_GCC and GCC_VERSION kernel config options
which are set at runtime and which should be ignored now.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This was found by the build bot.
Fixes: e29500eb84 ("kernel: bump 4.19 to 4.19.85")
Fixes: db9e9e8382 ("kernel: bump 4.14 to 4.14.155")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the netdev LED trigger for interfaces, which are renamed
during initialization (e.g. ppp interfaces).
Fixes: FS#2193
Fixes: FS#2239
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is related to the upstream kernel change 3b0f31f2b8c9 ("genetlink:
make policy common to family").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
generic: Add/rename patches for upstream consistency
ipq40xx: generic-level patch replaces same-source patches-4.19/
082-v4.20-mtd-spinand-winbond-Add-support-for-W25N01GV.patch
The SPI-NAND framework from Linux uses common driver code that is then
"tuned" by a tiny struct of chip-specific data that describes
available commands, timing, and layout (data and OOB data). Several
manufacturers and chips have been added since 4.19, several of which
are used in devices already supported by OpenWrt (typically with no or
"legacy" access to their NAND memory). This commit catches up the
supported-chip definitions through Linux 5.2-rc6 and linux/next.
The driver is only compiled for platforms with CONFIG_MTD_SPI_NAND=y.
This presently includes ipq40xx and pistachio, with the addition of
ath79-nand in these commits (and not ath79-generic or ath79-tiny).
Upstream patches refreshed against 4.19.75
Build-tested-on: ipq40xx
Run-tested-on: ath79-nand
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
This patch fixes the build of gdb and strace on arm64 targets with
kernel 4.19.
Without this patch asm/ptrace.h is including asm/sigcontext.h and this
file defines some structures which are also defined in musl header file
arch/aarch64/bits/signal.h. These two definitions then conflict with
each other and make the build fail.
This was seen locally and also by the build bot. The struct sigcontext,
struct sve_context and some others were defined twice. It looks like
this problem was introduced between 4.14 and 4.19 and it was fixed in
5.0. I already requested to backport this patch to kernel 4.19.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel 4.19 configuration contains the GCC version used, set it to
8.3.0 as this is now our default compiler.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes off-by-one error introduced in commit dc76900021
("kernel: Correctly search for the FIT image in mtd partition.")
Function `mtd_read` starts reading at `offset` and
needs `hdr_len` number of bytes to be available. Suppose
the easiest case when `offset` is `0` and `hdr_len` equals
to `mtd->size` - the `for` loop will not be entered even
when enough bytes are available to be read.
Same happens for any non-zero `offset`, when `hdr_len` is
just enough bytes to be read until `mtd->size` is reached.
Imagine that for example `mtd->size=5`, `offset=4` and
`hdr_len=1`. Then `offset+hdr_len=5` and the check has to
be `offset+hdr_len <= mtd->size`, i.e. `5 <= 5`. The
check for `offset + hdr_len` value needs to be inclusive,
therefore use `<=`.
Fixes: dc76900021 ("kernel: Correctly search for the FIT image in mtd partition.")
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
[adjusted commit ref, fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Replace an old cleanup patch that never made it upstream with the proper
upstream fix. This patch was incompatible with the recent changes that
affected the way that the flow tuple dst entry was used.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If an spi-gpio was specified with num-chipselects = <0> in dts, kernel
will crash:
Unable to handle kernel paging request at virtual address 32697073
pgd = (ptrval)
[32697073] *pgd=00000000
Internal error: Oops: 5 [# 1] SMP ARM
Modules linked in:
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.19.72 #0
Hardware name: Generic DT based system
PC is at validate_desc+0x28/0x80
LR is at gpiod_direction_output+0x14/0x128
...
[<c0544db4>] (validate_desc) from [<c0545228>] (gpiod_direction_output+0x14/0x128)
[<c0545228>] (gpiod_direction_output) from [<c05fa714>] (spi_gpio_setup+0x58/0x64)
[<c05fa714>] (spi_gpio_setup) from [<c05f7258>] (spi_setup+0x12c/0x148)
[<c05f7258>] (spi_setup) from [<c05f7330>] (spi_add_device+0xbc/0x12c)
[<c05f7330>] (spi_add_device) from [<c05f7f74>] (spi_register_controller+0x838/0x924)
[<c05f7f74>] (spi_register_controller) from [<c05fa494>] (spi_bitbang_start+0x108/0x120)
[<c05fa494>] (spi_bitbang_start) from [<c05faa34>] (spi_gpio_probe+0x314/0x338)
[<c05faa34>] (spi_gpio_probe) from [<c05a844c>] (platform_drv_probe+0x34/0x70)
The cause is spi_gpio_setup() did not check if the spi-gpio has
chipselect pins before setting their direction and results in derefing
an invalid pointer.
The bug is spotted in kernel 4.19.72 and does not occur in 4.14.
There is a similar fix upstream in kernel 5.2 in commit 249e2632dcd0
("spi: gpio: Don't request CS GPIO in DT use-case").
Ref: https://patchwork.kernel.org/patch/11150619/
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[use upstream patch, moved from hack to pending dir, commit facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Move the IRQ fix from generic to ar71xx specific.
Other targets like ath79 have specific pathes to delete this code.
This resulted in a build failure on ath79
While at it, wipe the 4.19 version, as ar71xx will never reach this.
Fixes: 530f76708cef ("ar71xx: Fix potentially missed IRQ handling during
dispatch")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
If both interrupts are set in the current implementation
only the 1st will be handled and the 2nd will be skipped
due to the "if else" condition.
Fix this by using the same approach as done for QCA955x
just below it.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The net pointer in struct xt_tgdtor_param is not explicitly
initialized therefore is still NULL when dereferencing it.
So we have to find a way to pass the correct net pointer to
ipt_destroy_target().
The best way I find is just saving the net pointer inside the per
netns struct tcf_idrinfo, which could make this patch smaller.
Fixes: 0c66dc1ea3f0 ("netfilter: conntrack: register hooks in netns when needed by ruleset")
Reported-and-tested-by: Tony Ambardar <itugrok@xxxxxxxxx>
Cc: Jamal Hadi Salim <jhs@xxxxxxxxxxxx>
Cc: Jiri Pirko <jiri@xxxxxxxxxxx>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
[Backport for kernel v4.19 and v4.14]
[Bug Link: https://bugzilla.kernel.org/show_bug.cgi?id=204681]
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
We are not sure if 640-bridge-only-accept-EAP-locally.patch is still needed
as a first step, add disable_eap_hack sysfs config to allow to disable it
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Refreshed all patches.
Also add a missing symbol for x86 which got used now in this bump.
- ISCSI_IBFT
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refreshed all patches.
Also add a missing symbol for x86 which got used now in this bump.
- ISCSI_IBFT
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85)
Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e)
Revert "ramips: add preliminary support for WIO ONE" (085141dc5b)
Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539)
Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d)
Revert "toolchain: add autoconf-lean" (fdb30eed03)
Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds support for uImage used by OpenWrt kernel loader.
The parser searches for uImage header at flash eraseblock boundary
and it might attempt to split any firmware with loader, therefore
this entry doesn't have MTD_PARSER_TYPE_FIRMWARE so that this parser
is only used when explicitly defined in dts.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This parser's matching function appears to be too generic as it matches
e.g. Buffalo WZR-HP-G300NH. That results in incorrect parts parsing.
Luckily this parser is needed by Fon FON2601 only which uses DT-based
ramips target. It means we can depend on mtd subsystem matching of
"fonfxc,uimage" string.
That said triggering this parser based on the "firmware" (or whatever
MTD_SPLIT_FIRMWARE_NAME is) partiiton name is not needed. It can be
dropped which will automatically fix the Buffalo WZR-HP-G300NH case.
Fixes: a1c6a316d2 ("ramips: add support for Fon FON2601")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This reverts commit e92a14709d.
mtdsplit_uimage_parse_fonfxc() gets called in two situations:
1) It was /requested/ from DT using "fonfxc,uimage" compatible string
2) It was called by parsing code after finding "firmware"
(MTD_SPLIT_FIRMWARE_NAME) due to the parser's type
Code added in the /fix/ commit basically just disabled the second case.
If that's the real goal it could be achieved by simply dropping type
MTD_PARSER_TYPE_FIRMWARE. It may however require another solution as
it's possible that some non-DT target actually needs fonfxc uImage
parsing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is already enabled as kernel built-in feature in mvebu target and
none other target will use it.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
We cannot distinguish between fonfxc uImage and generic uImage because
fonfxc uImage header is almost same as generic uImage, except padding
length after image name.
The fonfxc uImage parser is available when specifying directly with DT
compatible property. So this patch adds check if the partition DT node
is compatible with the parser.
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2413
Fixes: a1c6a316d2 ("ramips: add support for Fon FON2601")
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[commit light touches and removed C code comment]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
savedscp is a method of storing the DSCP of an ip packet into conntrack
mark. In combination with a suitable tc filter action (conndscp but may
end up being integrated into connmark) DSCP values are able to be stored
on egress and restored on ingress across links that otherwise alter or
bleach DSCP.
This is useful for qdiscs such as CAKE which are able to shape according
to policies based on DSCP.
Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway.
The ingress problem is solved by the tc filter, but the tc people didn't
like the idea of tc setting conntrack mark values, though they are ok
with reading conntrack values and hence restoring DSCP from conntrack
marks.
x_tables CONNMARK with the new savedscp action solves the problem of
storing the DSCP to the conntrack mark.
It accepts 2 parameters. The mark is a 32bit value with usually one 1
bit set. This bit is set when savedscp saves the DSCP to the mark.
This is useful to implement a 'one shot'
iptables based classification where the 'complicated' iptables rules are
only run once to classify the connection on initial (egress) packet and
subsequent packets are all marked/restored with the same DSCP. A mark
of zero disables the setting of a status bit/s.
The mask is a 32bit value of at least 6 contiguous bits and represents
the area where the DSCP will be stored.
e.g.
iptables -A QOS_MARK_eth0 -t mangle -j CONNMARK --savedscp-mark 0xfc000000/0x01000000
Would store the DSCP in the top 6 bits of the 32bit mark field, and use
the LSB of the top byte as the 'DSCP has been stored' marker.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This updates mac80211 to version 5.2-rc7, this contains all the changes
to the wireless subsystem up to Linux 5.2-rc7.
* The removed patches are applied upstream
* b43 now uses kmod-lib-cordic
* Update the nl80211.h file in iw to match backports version.
* Remove the two backports from kernel 4.9, they were needed for mt76,
but that can use the version from backports now, otherwise they
collide and cause compile errors.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop 211-host_tools_portability.patch which is breaking perf build on
4.19 kernels by removing the include directory from the host's CFLAGS
leading to the following build breakage:
pmu-events/jevents.c:48:10: fatal error: linux/list.h: No such file or directory
#include <linux/list.h>
^~~~~~~~~~~~~~
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is already included in newer upstream. Needed to build BPF programs
using the MIPS kernel include files.
Without this patch, clang fails with "#error Use a Linux compiler or
give up." in sgidefs.h when building BPF programs.
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
CAKE made it to kernel 4.19 and since OpenWrt now at kernel 4.19 we can
drop the out of tree cake package in base repository.
Add kmod-sched-cake to netsupport so package dependencies are still met.
Similarly CAKE is retained as an optional qdisc module to avoid base
scheduler package size implications.
Backport upstream patches from k5.1 to address some small bugs and
support fwmark usage.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This fixes the following compile problem with kernel 4.9 on lantiq:
drivers/mtd/mtdsplit/mtdsplit_uimage.c:244:34: error: array type has incomplete element type 'struct of_device_id'
static const struct of_device_id mtdsplit_uimage_of_match_table[] = {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/mtdsplit/mtdsplit_uimage.c:245:4: error: field name not in record or union initializer
{ .compatible = "denx,uimage" },
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is pending to get into the upstream kernel.
This fixes a bug in the upstream kernel which was added to stable some
time ago.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch backports verbatim the commit from Linux 5.2-rc7 that fixes
the warnings about invalid lpm related parameters on hardware which
don't that.
This is the case for e.g. lantiq xrx200 targets.
Supported only in Linux 4.17 an later.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[refresh patches, fix commit title]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fixes following kernel build issue on ath79 with CONFIG_KERNEL_FTRACE=y
enabled:
Tracers (FTRACE) [Y/n/?] y
Kernel Function Tracer (FUNCTION_TRACER) [Y/n/?] y
Kernel Function Graph Tracer (FUNCTION_GRAPH_TRACER) [Y/n/?] y
Enable trace events for preempt and irq disable/enable (PREEMPTIRQ_EVENTS) [N/y/?] (NEW)
...
Preempt / IRQ disable delay thread to test latency tracers (PREEMPTIRQ_DELAY_TEST) [N/m/?] (NEW)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit fcb41decf6 ("config: enable some useful features on
!SMALL_FLASH devices") enabled netns, which in turn lead to the crash in
the flow offload target.
When the flow offloading framework intends to delete a flow from the
hardware table, it is necessary to retrieve the namespace from
nf_flowtable->ft_net. However, no one ever wrote the namespace into
nf_flowtable->ft_net in advance. So the framework will mistakenly use a
NULL namespace to execute dev_get_by_index_rcu(net, ifindex), leading to
the kernel panic.
Ref: FS#2321
Fixes: fcb41decf6 ("config: enable some useful features on !SMALL_FLASH devices")
Tested-by: Simon Tretter <simon@mediaarchitectu.re>
Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
[merged patch into offload patch, fix for 4.19, SOB fix, commit subj/msg touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds a promising upstream patch that claims
to help for the treated I/O errors happening on f2fs
or ext4 on real block devices.
|print_req_error: I/O error, dev loop1, sector 1334
Link: <https://patchwork.kernel.org/cover/10931787/>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
bnx2x driver support for the x86 architecture. Includes module and
firmware for Broadcom QLogic 5771x/578xx 10/20-Gigabit ethernet
adapters.
Signed-off-by: Petko Bordjukov <bordjukov@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added +kmod-lib-zlib-inflate as well]
