Commit Graph

56022 Commits

Author SHA1 Message Date
Pawel Dembicki
2e4fe289ce layerscape: Fix SPI-NOR issues with vendor patches
For some reason LS1012A and LS1046A devboards don't work well with
Spansion SPI NOR flash. It cause read and write errors like:

[   27.285887] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x025ae000
[   27.468922] jffs2: Newly-erased block contained word 0x0 at offset 0x02573000
[   27.502615] jffs2: Newly-erased block contained word 0xe723f41e5823f110 at offset 0x02572000
[   27.541550] jffs2: Newly-erased block contained word 0x1a7d266ee6 at offset 0x02571000
[   27.577195] jffs2: Newly-erased block contained word 0x5d000bae8d52fec6 at offset 0x02570000
[   27.611800] jffs2: Newly-erased block contained word 0x63515aee63515a4b at offset 0x0256f000
[   27.651749] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0256e000
[   27.825593] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0252e000

NXP have found workarround and applied in their vendor kernel version.
They force 1x tx and 1x rx lines in qspi. That method fix issues.
This patch ports patches from NXP LSDK tree.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Will Moss
a58146d452 ath79: D-Link DIR-825 B1 add factory.bin recipe
- Bring back factory.bin image which was missing after porting device to ath79 target
- Use default sysupgrade.bin image recipe
- Adjust max image size according to new firmware partition size after
"ath79: expand rootfs for DIR-825-B1 with unused space (aca8bb5)" changes
- Remove support of upgrading from version 19.07, because partition size changes mentioned above

Signed-off-by: Will Moss <willormos@gmail.com>
2022-11-27 13:18:29 +01:00
Michael Pratt
6de9287abd ath79: add support for Senao Engenius EAP1750H
FCC ID: A8J-EAP1750H

Engenius EAP1750H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

**Specification:**

  - QCA9558 SOC
  - QCA9880 WLAN	PCI card, 5 GHz, 3x3, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM	NT5TU32M16FG
  - UART at J10		populated
  - 4 internal antenna plates (5 dbi, omni-directional)
  - 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)

**MAC addresses:**

  MAC addresses are labeled as ETH, 2.4G, and 5GHz
  Only one Vendor MAC address in flash

  eth0 ETH  *:fb art 0x0
  phy1 2.4G *:fc ---
  phy0 5GHz *:fd ---

**Serial Access:**

  the RX line on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin at J10

**Installation:**

  2 ways to flash factory.bin from OEM:

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

**Return to OEM:**

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

**TFTP recovery:**

  Requires serial console, reset button does nothing

  rename initramfs to 'vmlinux-art-ramdisk'
  make available on TFTP server at 192.168.1.101
  power board, interrupt boot
  execute tftpboot and bootm 0x81000000

  NOTE: TFTP is not reliable due to bugged bootloader
  set MTU to 600 and try many times
  if your TFTP server supports setting block size
  higher block size is better.

**Format of OEM firmware image:**

  The OEM software of EAP1750H is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin
    openwrt-ar71xx-generic-eap1750h-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-11-27 13:18:29 +01:00
Michael Pratt
128947db42 ath79: use nvmem-cells for radio calibration of EAP1200H
Transition from userscript to DTS for all of ART.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-11-27 13:18:29 +01:00
Edward Chow
2c33fd39a5 ath79: calibrate TP-LINK TL-WR2543ND with nvmem
Driver for and pci wlan card now pull the calibration data from the nvmem
subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.

Test passed on my tplink tl-wr2543nd.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-27 13:18:29 +01:00
Shiji Yang
9fa8fff0af scripts: remove redundant character '0x0a' from Linksys image signature
The redundant character '0x0a' after the 192 bytes '0x00' padding broke
the factory image. We need to remove it to make things work again.

Fixes: e6769d11f3 scripts: fix missing character '0' issue in linksys image
Tested-by: Tony Butler <spudz76@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-27 13:18:29 +01:00
John Audia
acb10faa35 kernel: bump 5.10 to 5.10.156
Manually rebased: ath79/patches-5.10/910-unaligned_access_hacks.patch

All other patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-27 13:18:29 +01:00
John Audia
590aa0ca51 kernel: bump 5.15 to 5.15.80
Manually rebase:
   pending-5.15/330-MIPS-kexec-Accept-command-line-parameters-from-users.patch
   ath79/patches-5.15/910-unaligned_access_hacks.patch

All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-27 13:18:29 +01:00
Nick Hainke
6640c788fe mac80211: subsys: complete patch files for use with git am
Adding proper fields to patch files allowing for `git am` to properly
function.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-27 13:18:29 +01:00
Tony Butler
3d205eb216 wolfssl: fix Config.in typo
Fix simple typo `/crytpo/crypto/` in a description string

Signed-off-by: Tony Butler <spudz76@gmail.com>
2022-11-27 12:58:33 +01:00
Nick Hainke
745f1ca976 wolfssl: update to v5.5.3
Remove "200-ecc-rng.patch" because it was upstramed by:
e2566bab21
Refreshed "100-disable-hardening-check.patch".

Fixes CVE 2022-42905.

Release Notes:
- https://github.com/wolfSSL/wolfssl/releases/tag/v5.5.2-stable
- https://github.com/wolfSSL/wolfssl/releases/tag/v5.5.3-stable

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-27 12:58:33 +01:00
Nick Hainke
68714f2135 ipset: update to 7.16
Release Notes:
https://lore.kernel.org/netfilter-devel/d65fe5d8-d5ea-ef7-102d-aa1d15bb4d69@netfilter.org/T/#u

Patch "0001-lib-ipset-fix-printf-warning.patch" replaced upstream by:
http://git.netfilter.org/ipset/commit/?id=e39e3466d2d38cdfe83447f391b550e607bc3ce8

Remove upstreamed:
- 0002-Fix-IPv6-sets-nftables-translation.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-27 12:58:33 +01:00
Rosen Penev
2cb48f58c2 nls.mk: fixup cmake packages
Instead of manually overriding every cmake package that uses iconv or
gettext's paths, add the prefix in here so that at least FindIconv.cmake
works. Fixes compilation with BUILD_NLS.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-11-27 00:52:06 +01:00
Nick Hainke
6bac7bbf46 tools/mpfr: update to 4.1.1
Changes:
- Bug fixes
- Improved manual formatting

Refresh patches:
- 001-only_src.patch

Import patch fixing macro bug:
- 002-Fix-mpfr_custom_get_kind-macro-bug.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-27 00:52:06 +01:00
Nick Hainke
9a542930cd tools/bash: update to 5.2.9
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-26 17:04:33 +01:00
Christian Marangi
60fc93b359
ipq806x: disable cache and fabric devfreq driver to improve stability
It was tested that cache scaling currently cause instability problem.
This is probably caused by a latent misconfiguration that cause the L2
cache to be sourced from the wrong source and runs at an unstable freq
compared to the original QSDK fw.

To improve stability while the problem is bisected, disable the devfreq
drivers with minimal perf penality.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-11-26 00:38:31 +01:00
Felix Fietkau
3dff6b53db kernel: fix mtk_eth_soc issue when using secondary GMAC on MT7621/MT7622
The CDMQ ingress special tag flag needs to be set for 7986 even without DSA
untag offload, otherwise tx checksum offload seems to break

Fixes: 9b482ee22f ("kernel: add more fixes for mtk_eth_soc")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-25 01:56:53 +01:00
Daniel Golle
c1d1202e67
mediatek: set persistent wifi mac for bpi-r64 and bpi-r3
Use persistent MAC address for the built-in wireless interfaces of the
BPi-R64 and BPi-R3 development boards.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-24 16:46:33 +00:00
Daniel Golle
87fc485450
ipq40xx: remove '-fit' string from kernel filenames
The type of those images is already distinguishable by the '.itb'
extension, there is no need for an additional '-fit' string in the
filenames. Remove it to behave more like other targets.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-24 16:46:28 +00:00
Daniel Golle
d9f7c751c9
ipq40xx: remove 'nand-' string from image filenames
Only on the ipq40xx subtarget different filenames were used for NAND-
based devices. This is unneeded, confusing and breaks downstream tools
such as luci-app-attendedsysupgrade and auc.
Remove the 'nand-' string from image filenames to fix that.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-24 16:46:18 +00:00
Alexander Couzens
4943ce98ff
kernel/module/iio: add TI am335x ADC driver
Add the iio driver for the embedded ADC in the
TI Sitara am335x SoCs.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2022-11-24 15:47:01 +00:00
Edmunt Pienkowsky
c34eab6fd1 bcm27xx: sound-soc-justboom-*: fix packages
Affected packages: sound-soc-justboom-both, sound-soc-justboom-dac and sound-soc-justboom-digi.

- Add snd-soc-wm8804-i2c and/or snd-soc-pcm512x-i2c kernel modules.
- Add kmod-regmap-i2c package dependency.

Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
2022-11-23 20:17:21 +01:00
Edmunt Pienkowsky
0889adf16f bcm27xx: sound-soc-hifiberry-digi: fix package
- Add snd-soc-wm8804-i2c kernel module,
- Add kmod-regmap-i2c package dependency.

Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
2022-11-23 20:17:18 +01:00
John Audia
3f7cc9d014 bcm27xx: disable duplicate sdhost driver
Enabling both CONFIG_MMC_BCM2835 and CONFIG_MMC_BCM2835_SDHOST causes this
error in dmesg:
Error: Driver 'sdhost-bcm2835' is already registered, aborting...

Disabling CONFIG_MMC_BCM2835 and leaving CONFIG_MMC_BCM2835_SDHOST enabled
avoids this error.

Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
[Disable driver for all subtargets, refresh configs, tweak description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2022-11-23 20:13:46 +01:00
Felix Fietkau
eaba63cdde kernel: fix regression on mt7986
The CDMQ ingress special tag flag needs to be set for 7986 even without DSA
untag offload, otherwise tx checksum offload seems to break

Fixes: 9b482ee22f ("kernel: add more fixes for mtk_eth_soc")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-23 11:34:43 +01:00
Felix Fietkau
4e1a6ee903 kernel: add WED rx support for mediatek
This is required for rx flow offloading on mt76 with MT7986 and MT7915

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-21 20:46:47 +01:00
Felix Fietkau
e410833bdd kernel: add a locking fix for netfilter hardware flow offloading
Protect the flow block cb list readers against concurrent updates

Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-21 20:44:01 +01:00
Felix Fietkau
9b482ee22f kernel: add more fixes for mtk_eth_soc
Fix corner cases in DSA offload
Add refcounting fix for flow offload
Fix VLAN untagging issue on MT7986

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-21 11:47:36 +01:00
Thomas Weißschuh
0d375de10d tools/patch: apply patch for EACCES on xattr copy
When compiling OpenWRT on a compressed btrfs volume the build fails in
libtool.
The file `libltdl/config/ltmain.m4sh` from `libtool-2.4.2.tar.xz` is
missing write permissions, therefore patch falls back to copying the
file and patching that. During this patch tries to preserve all file
attribute on the new copy.
However the attribute `btrfs.compression` is privileged and btrfs return
EACCES.
While patch ignores multiple other error codes during the copy of xattr
copy it is not prepared for EACCES and aborts.

EACCES should be ignored the same way as the other errors.

Build log:
```
...
Applying ./patches/000-relocatable.patch using plaintext:
patching file libltdl/config/general.m4sh
patching file libtoolize.in
patching file libtoolize.m4sh
patching file libltdl/m4/libtool.m4

Applying ./patches/100-libdir-fixes.patch using plaintext:
patching file libltdl/config/ltmain.m4sh
File libltdl/config/ltmain.sh is read-only; trying to patch anyway
patching file libltdl/config/ltmain.sh
patch: setting attribute btrfs.compression for btrfs.compression: Permission denied
Patch failed!  Please fix ./patches/100-libdir-fixes.patch!
```

Link: https://lists.gnu.org/archive/html/bug-patch/2022-11/msg00000.html
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
2022-11-20 18:44:43 +01:00
Maxim Anisimov
21762e4653 ramips: add support for Keenetic KN-3010
Keenetic KN-3010 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7621DAT.

Specification:
- System-On-Chip: MT7621DAT
- CPU/Speed: 880 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100/1000 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): MT7603E 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch

Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
  wifi indicator.

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3010-squashfs-factory.bin"
   to "KN-3010_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2022-11-20 16:44:24 +01:00
Xiaopo Zhang
a28297d395 x86: enable PINCTRL for all Intel platform
Enable Intel PINCTRL for all platform on both 32 bit and 64 bit target.

Signed-off-by: Xiaopo Zhang <xiaopoz@proton.me>
2022-11-20 16:31:10 +01:00
Xiaopo Zhang
34615250a9 x86/64: enable Intel PINCTRL in 64bit target
Intel PINCTRL is not enable in the 64bit build, while it is enabled in
the x86/general target, which disables the ability of controlling GPIO
in the 64 bit build.

This commit copies the corresponding part of x86/general config, since
it is already there, so it should be fine to enable the same settings
here.

Signed-off-by: Xiaopo Zhang <xiaopoz@proton.me>
2022-11-20 16:31:10 +01:00
Will Moss
288b0004bf ath79: fix MAC address assigment for TP-Link TL-WR740N/TL-WR741ND v4
On TP-Link TL-WR740N/TL-WR741ND v4 LAN MAC address (eth1 in DTS) is main
device MAC address, so do not increment it. WAN MAC is LAN MAC + 1.

Signed-off-by: Will Moss <willormos@gmail.com>
2022-11-20 16:30:27 +01:00
Roger Pueyo Centelles
5a1d7d8c1b ath79: disable image building for Ubiquiti EdgeSwitch 8XP
The downstream OpenWrt driver for the BCM53128 switch ceased to work,
rendering the 8 LAN ports of the device unusable. This commit disables
image building while the problem is being solved.

See issue #10374 for more details.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2022-11-20 16:24:24 +01:00
Edward Chow
3d343ca713 ath79: calibrate nand netgear wndrxxxx with nvmem
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.

The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.

Test passed on my wndr3700v4 and wndr4500v3.
Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-20 16:13:48 +01:00
Aleksander Jan Bajkowski
bca663f20f kernel: backport tso for asix driver
Performance comparison (iperf3, mtu 1500):
Before: 53.9 Mbps
After: 87.9 Mbps

The tests were performed on a BT Home Hub 5A router.
The iperf3 server was running on the router, the client
on the host.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Christian Buschau
084c20f6c5 lantiq: xway: kernel: enable SMP support
Enabled CONFIG_MIPS_MT_SMP and CONFIG_SCHED_SMT.

Tested on FRITZ!Box 7330 SL, 7312 and o2 Box 4421.

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-11-18 20:27:52 +01:00
Christian Buschau
d3527bb83b lantiq: xway: ar9: add ICU1 (2nd core for SMP)
Fixes leftover TODO from commit 6bf179b270

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-11-18 20:27:52 +01:00
Christian Buschau
fb0256e88e lantiq: xway: refresh kernel config
Run of 'make kernel_oldconfig CONFIG_TARGET=subtarget'

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-11-18 20:27:52 +01:00
Edward Chow
e354b01baf ath79: calibrate all ar9344 tl-WDRxxxx with nvmem
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.

The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.

Test passed on my tplink tl-wdr4310.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-18 20:27:52 +01:00
Aleksander Jan Bajkowski
224babfd6f mediatek: mt7623: disable swconfig
The mt7623 subtarget supports 2 devices:
 * Bananapi BPi-R2 (added in 1f068588ef, 7762c07c88),
 * UniElec U7623-02 (added in 4def81f30f).

Both devices support DSA from the beginning, thus
swconfig can be safely disabled.

In the past, the subtarget mt7623 also supported
the mt7623 reference board. This board originally
supported swconfig, and was later converted to DSA
(64175ffb79) and then dropped (1ab81bf02d).

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Aleksander Jan Bajkowski
0e001e4185 mediatek: mt7623: refresh config
This was done by executing these command:
$ time make kernel_oldconfig CONFIG_TARGET=subtarget

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Jonas Albrecht
74a5718223 lantiq: ltq-tapi: add customer pulse digit time
With this patch you can change the pulse digit time by loading the Lantiq
FXS driver kernel module called ltq-tapi. This is relevant for old
rotaryphones that uses pulsedialing.

The default values are:
30-80ms for the low pulse
30-80ms for the high pulse
300ms for minimum Interdigit time

this is OK but on some Phones it can be usefull to customize the values
If you want to change the values to high and low pulse to 40-90ms and
minimum interdigit time to 400ms

than change /etc/modules.d/20-ltq-tapi to (without linebrakes):
drv_tapi min_digit_low=40  min_digit_high=90 max_digit_low=40 \
max_digit_high=90 min_interdigit=400

Signed-off-by: Jonas Albrecht <plonkbong100@protonmail.com>
2022-11-18 20:27:52 +01:00
Moritz Warning
dc7d431b60 treewide: uniform vendor name for devolo
The company name is lower case on the website
(https://www.devolo.de) and in product names.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2022-11-18 20:27:52 +01:00
Nick Hainke
8db2db9890 libtracefs: update to 1.6.1
Update to latest version.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-18 20:27:52 +01:00
Nick Hainke
c17b6343f3 lldpd: update to 1.0.16
Release Notes:
https://github.com/lldpd/lldpd/releases/tag/1.0.16

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-18 20:27:52 +01:00
Nick Hainke
64373d2a12 tools/sed: update to 4.9
Release Notes:
https://lists.gnu.org/archive/html/info-gnu/2022-11/msg00001.html

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-18 19:52:54 +01:00
Álvaro Fernández Rojas
1996d600bd cypress-firmware: update to v5.10.9-2022_0909
The following firmwares have been updated:
- cyfmac43012-sdio (v13.10.271.266 -> v13.10.271.289)
- cyfmac43430-sdio (v7.45.98.118 -> v7.45.98.125)
- cyfmac43455-sdio (v7.45.234 -> v7.45.250)
- cyfmac4354-sdio (v7.35.349.104 -> v7.35.349.117)
- cyfmac4356-pcie (v7.35.180.208 -> v7.35.180.212)
- cyfmac4356-sdio (v7.35.349.104 -> v7.35.349.115)
- cyfmac4373-sdio (v13.10.246.253 -> v13.10.246.289)
- cyfmac4373-usb (v13.10.246.253 -> v13.10.246.289)
- cyfmac54591-pcie (v13.35.225 -> v13.35.284)

The following firmwares have been added:
- cyfmac43439-sdio (v7.95.55)
- cyfmac4373-pcie (v13.35.205.66)
- cyfmac54591-sdio (v13.35.284)
- cyfmac55560-pcie (v18.53.53.4)
- cyfmac55572-pcie (v18.53.117.2)
- cyfmac55572-sdio (v18.53.117.2)

More info: https://github.com/Infineon/ifx-linux-firmware/compare/release-v5.4.18-2021_0812...release-v5.10.9-2022_0909

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2022-11-17 16:43:55 +01:00
Álvaro Fernández Rojas
0db537975d cypress-firmware: fix cyfmac4356-pcie symbolic links
The symbolic link introduced in 22e9d8bc89 is wrong.

Fixes: 22e9d8bc89 ("cypress-firmware: use symlink to provide firmware in brcm")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2022-11-17 12:27:41 +01:00
Daniel Golle
4c67d1e066 uboot-mediatek: optimize MMC erase
Fix mmc_write_vol hush script used by many boards to avoid timeouts on
slow SD cards:
Instead of erasing a complete partition, only erase blocks for the
to-be-written image when writing to MMC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-17 01:55:55 +00:00