Add 1920-24g-poe-180w to the mac address retrieval part of 02_network to
properly set the device's port MAC addresses.
This piece was missed when this device was added.
Fixes: b948c1e39b ("realtek: add support for HPE 1920-24G PoE-180W (JG925A)")
Link: https://github.com/openwrt/openwrt/pull/17460
Signed-off-by: James Sweeney <code@swny.io>
d996988ae55b libubus: close file descriptor after sending it from a request
afa57cce0aff libubus: add support for using channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The extraneous closing parenthesis inside the case matching breaks
syntax of the network initialization script 02_network.
/bin/board_detect: /etc/board.d/02_network:
line 40: syntax error: unexpected newline (expecting ")")
Remove this character so board init is functional again.
Fixes: c8ea1aa970 ("realtek: add support for HPE 1920-24G-PoE-370w")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.
The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some ixp4xx platforms with a proper RedBoot config do not
contain the per-ethernet interface npe_eth0_esa, but rather
a single entry named zcom_npe_esa.
Let's use this if fconfig can't find the primary key.
This is needed on the Netgear WG302 v1.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WG302 v1 have a separate rootfs partition that we
simply just upgrade with a new rootfs image. The kernel
need to be updated on the TFTP server.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WG302 v1 has 32MB of RAM so it can easily run OpenWrt,
however it lacks much flash: only 8 MB.
By just using the flash for rootfs and booting a kernel over
TFTP it works just fine.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hardware information: (largely copied from 11275be)
---------------------
The HPE 1920-24G-PoE+ (180W) (JG925A) is a switch that is
part of the 1920 family which has 180W nominal PoE+ support.
Common with HPE 1920-24G:
- RTL8382 SoC
- 24 Gigabit RJ45 ports (built-in RTL8218B, 2 external RTL8218D)
- 4 SFP ports (external RTL8214FC)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
HPE 1920-24G-PoE+ (180W):
- PoE chip
- 2 fans (40mm)
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '180'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '9'
option name 'lan16'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '10'
option name 'lan15'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '11'
option name 'lan14'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '12'
option name 'lan13'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '13'
option name 'lan12'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '14'
option name 'lan11'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '15'
option name 'lan10'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '16'
option name 'lan9'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '17'
option name 'lan24'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '18'
option name 'lan23'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '19'
option name 'lan22'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '20'
option name 'lan21'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '21'
option name 'lan20'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '22'
option name 'lan19'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '23'
option name 'lan18'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '24'
option name 'lan17'
option poe_plus '1'
option priority '2'
Signed-off-by: James Sweeney <code@swny.io>
Link: https://github.com/openwrt/openwrt/pull/17444
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Switch to using loader-kernel to accommodate
larger image sizes that are problematic for
many mt7621 uboots.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
Link: https://github.com/openwrt/openwrt/pull/17389
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The debounce-interval of a gpio-keys node should be placed in the key
node itself, not in the main node. Move the properties added earlier and
fix the key node name while we're here.
Fixes: 4357f32d41 ("realtek: debounce reset key for Zyxel GS1900")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
During port to gluon, I saw that the primary mac is not correct. Updated DTS accordingly.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17429
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When the reset button is next to the SFP cages, I2C operations on the
modules might cause interference on the button's GPIO line. Add a
debounce-interval of 5 times the poll-interval to ensure the line is
actually stable for some time and not just glitching.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Check the return value of malloc and pread in case they fail.
Signed-off-by: Qiyuan Zhang <zhang.github@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add kernel command line replacement hack to qualcommax. Now we can
find and replace arguments in the kernel command line by setting
bootargs-find-1, bootargs-replace-1, bootargs-exact-match-1
and bootargs-find-2, bootargs-replace-2, bootargs-exact-match-2
under the chosen node in the device tree.
This hack replaces the first occurence of bootargs-find-X with
bootargs-replace-X. When bootargs-exact-match-X is set to "y",
then the replacement happens only if the kernel command line is
identical to bootargs-find-X.
Signed-off-by: Qiyuan Zhang <zhang.github@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix a bug in linksys_bootcount.c that resetbc won't work on nand
with min I/O size> 2048.
Check the boot-log entry's intergrity with checksum.
Signed-off-by: Qiyuan Zhang <zhang.github@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently for Linksys MX4200v2 all u-boot ethXaddr variables share the same MAC address
and there is no need to check them one by one.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Define shared configuration for Linksys MX4x00 devices.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Create a generic Linksys MX4x00 dts file and extract the specific configuration
for MX4200v1/v2 to a new file.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
The default value for the "root" parameter is "/dev/ubiblock0_0"
and there is no need to append it to bootargs.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Missing limits.h. Upstream backport.
Add extra backports. Replace Alpine Linux patch with upstream one. Same
with patch 400.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17426
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware information:
---------------------
The HPE 1920-24G-PoE+ (370W) (JG926A) is a switch that is
part of the 1920 family wich 370W nominal PoE+ support.
Common with HPE 1920-24G:
- RTL8382 SoC
- 24 Gigabit RJ45 ports (built-in RTL8218B, 2 external RTL8218D)
- 4 SFP ports (external RTL8214FC)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
HPE 1920-24G-PoE+ (370W):
- PoE chip
- 3 fans (40mm)
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '370'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '9'
option name 'lan16'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '10'
option name 'lan15'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '11'
option name 'lan14'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '12'
option name 'lan13'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '13'
option name 'lan12'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '14'
option name 'lan11'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '15'
option name 'lan10'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '16'
option name 'lan9'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '17'
option name 'lan24'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '18'
option name 'lan23'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '19'
option name 'lan22'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '20'
option name 'lan21'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '21'
option name 'lan20'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '22'
option name 'lan19'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '23'
option name 'lan18'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '24'
option name 'lan17'
option poe_plus '1'
option priority '2'
Signed-off-by: Evan Jobling <evan.jobling@mslsc.com.au>
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Link: https://github.com/openwrt/openwrt/pull/17436
[fix space indentation in DTS]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The HPE JG924A, JG925A and JG926A share the same base.
Prepare base device for adding the PoE enabled switch support.
Signed-off-by: Evan Jobling <evan.jobling@mslsc.com.au>
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Link: https://github.com/openwrt/openwrt/pull/17436
Signed-off-by: Sander Vanheule <sander@svanheule.net>
109114146f9c mt76: only enable tx worker after setting the channel
5fe42ec88fd1 mt76: mt7915: ensure that only one sta entry is active per mac address
1884f568ba02 wifi: mt76: do not add wcid entries to sta poll list during MCU reset
71fa9124d107 wifi: mt76: mt7996: fix NULL pointer dereference in mt7996_mcu_sta_bfer_he
eb85bb3fd5bf wifi: mt76: mt7915: fix eifs value on older chipsets
83e4d4a82e65 wifi: mt76: introduce mt792x_config_mac_addr_list routine
b47e20b440ae wifi: mt76: mt7925: fix NULL deref check in mt7925_change_vif_links
3e3c484726f3 wifi: mt76: mt7925: fix wrong band_idx setting when enable sniffer mode
3f1401a0f035 wifi: mt76: mt7925: fix get wrong chip cap from incorrect pointer
eede99f524e8 wifi: mt76: mt7925: fix the invalid ip address for arp offload
c99e4d51b340 wifi: mt76: mt7996: fix overflows seen when writing limit attributes
af983b2543ed wifi: mt76: mt7915: fix overflows seen when writing limit attributes
af494e2dcc94 wifi: mt76: mt7915: exclude tx backoff time from airtime
6f6a1f7cb381 wifi: mt76: mt7996: exclude tx backoff time from airtime
7f65b1b28b4c wifi: mt76: connac: Extend mt76_connac_mcu_uni_add_dev for MLO
1b5e6abc2e7a wifi: mt76: mt7925: Fix incorrect MLD address in bss_mld_tlv for MLO support
72b4688b3912 wifi: mt76: mt7925: Fix incorrect WCID assignment for MLO
6bd2c044e67a wifi: mt76: mt7925: Fix incorrect WCID phy_idx assignment
1c04e9693466 wifi: mt76: mt7925: fix wrong parameter for related cmd of chan info
01e02947bdbf wifi: mt76: mt7925: Fix CNM Timeout with Single Active Link in MLO
b90b1a1dc71b wifi: mt76: mt7925: Enhance mt7925_mac_link_bss_add to support MLO
53ec7a551f17 wifi: mt76: Enhance mt7925_mac_link_sta_add to support MLO
3c99ef40e0e7 wifi: mt76: mt7925: Update mt7925_mcu_sta_update for BC in ASSOC state
285efc6afaec wifi: mt76: mt7925: Update mt792x_rx_get_wcid for per-link STA
e5c0d1289e6c wifi: mt76: mt7925: Update mt7925_unassign_vif_chanctx for per-link BSS
67dcd5c888c4 wifi: mt76: mt7925: Update secondary link PS flow
fd4d6f87072f wifi: mt76: mt7925: Init secondary link PM state
6d972b5b9d6a wifi: mt76: mt7925: Update mt7925_mcu_uni_[tx,rx]_ba for MLO
3acc6cbb9556 wifi: mt76: mt7925: Cleanup MLO settings post-disconnection
0aab0c61ce92 wifi: mt76: mt7925: Properly handle responses for commands with events
15bead1b0041 wifi: mt76: do not hold queue lock during initial rx buffer alloc
732044a949d5 wifi: mt76: mt7925: config the dwell time by firmware
9ba311ec6afa wifi: mt76: mt7921: introduce CSA support
5d12c7404c22 wifi: mt76: mt7921: add rfkill_poll for hardware rfkill
ef965d408b79 wifi: mt76: mt7925: replace zero-length array with flexible-array member
f8563589c72d wifi: mt76: mt7921u: Add VID/PID for TP-Link TXE50UH
Signed-off-by: Felix Fietkau <nbd@nbd.name>
They show up as null entries in the nl80211 wiphy dump.
Fixes the following error:
Reference error: left-hand side expression is null
In find_phy(), file /usr/share/ucode/iwinfo.uc, line 19, byte 11:
called from function get_max_power (/usr/share/ucode/iwinfo.uc:42:32)
called from function module (/usr/share/ucode/iwinfo.uc:102:39)
called from anonymous function (/usr/bin/iwinfo:5:25)
` if (phy.wiphy == wiphy)`
Near here ------^
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Delete CONFIG_LIST_HARDENED which you already find in target/generic config.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/17420
Signed-off-by: Nick Hainke <vincent@systemli.org>
The fritz 300e has an AR9382, which is atypical for ar7242 platforms.
Document it properly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17427
Signed-off-by: Nick Hainke <vincent@systemli.org>
Netgear Orbi devices rely on ethernet0 alias to be present to U-Boot will
populate the MAC.
This fixes the random MAC on each boot after the ethernet0 alias was
dropped from the SoC DTSI.
Fixes: cd9c721124 ("ipq40xx: 6.1: use latest DSA and ethernet patches")
Fixes: #17384
Link: https://github.com/openwrt/openwrt/pull/17414
Signed-off-by: Robert Marko <robimarko@gmail.com>
When doing LTO builds, the target related CFLAGS need to be passed to the
linker, so that they are considered for target code generation.
Pass TARGET_CFLAGS in EXTRA_LDFLAGS to ensure that this is handled properly.
Fixes: #17200
Signed-off-by: Felix Fietkau <nbd@nbd.name>
These PHY LED-s are leftovers from a time when PHY LED offloading did not
work like the stock FW, so remove them as they are commented-out anyway.
Link: https://github.com/openwrt/openwrt/pull/17413
Signed-off-by: Robert Marko <robimarko@gmail.com>
Right now there's no way to know what state CFE will leave the pinctrl
registers in, so they should be explicitly set by linux on boot. This
patch adds a gpio configuration for drivers that need it, i.e. gpio-leds.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[improve patch and fix warnings]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Update to the latest upstream release to include recent improvements and
bugfixes, and simplify use of PKG_SOURCE_VERSION.
This version supports BPF objects of either endianness, allowing for
introspection, linking and skeleton creation, and enables cross-compiling
modern BPF applications for targets with non-native byteorder.
Link: https://github.com/libbpf/bpftool/releases/tag/v7.5.0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/17404
Signed-off-by: Nick Hainke <vincent@systemli.org>
