Several devices in mt76x8 subtarget use the following line to set
up wmac in their DTS(I) files:
ralink,mtd-eeprom = <&factory 0x4>
This is strange for several reasons:
- They should use mediatek,mtd-eeprom on this SOC
- The caldata is supposed to start at 0x0
- The parent DTSI mt7628an.dtsi specifies mediatek,mtd-eeprom anyway,
starting from 0x0
- The offset coincides with the default location of the MAC address
in caldata
Based on the comment in b28e94d4bf ("ramips: MiWiFi Nano fixes"),
it looks like the author for this device wanted to actually use
mtd-mac-address instead of ralink,mtd-eeprom. A check on the same
device revealed that actually the MAC address start at offset 4 there,
so the correct caldata offset is 0x0.
Based on these findings, and the fact that the expected location on
this SOC is 0x0, we remove the "ralink,mtd-eeprom = <&factory 0x4>"
statement from all devices in ramips (being only mt7628an anyway).
Thanks to Sungbo Eo for finding and researching this.
Reported-by: Sungbo Eo <mans0n@gorani.run>
Fixes: b28e94d4bf ("ramips: MiWiFi Nano fixes")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 09d38a3bc3)
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.
Specification:
- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/1000 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)
Other:
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
has additional logic circuit for M.2 SIM switching. The 'sim-select'
will work only if both SIM slots are occupied. Otherwise, always slot
with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
slots but setting GPIO22 to high allows PERSTn control per slot, using
GPIO23-25 (value is inverted)
Flash instructions:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit e68539aca4)
ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform
based on MediaTek MT7620A WiSoC. This product is designed for operation
with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06)
but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses).
Specification:
- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32+ MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 2x u.fl antenna connectors (for Wi-Fi)
- 8x LED (7 driven by GPIO)
- 2x button (reset, wifi)
- 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB
- 1x I2C (4-pin, 1.27 mm pitch) header on PCB
- 1x LED (8-pin, 1.27 mm pitch) header on PCB
- 1x DC jack with lock (12 V)
Other:
- there is a dedicated, 4-pin connector for optional RTC module (Holtek
HT138x) with 'enable' input, not available at the time of preparing
support for this board
- miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a
jumper resistor (R174) is not installed by default
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will
work only if both slots are occupied, otherwise U-Boot will always
select slot with SIM card inside (user can override it later, in
user-space)
- U-Boot resets the modem, using PERSTn signal, before starting kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
Flash instruction:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit dfecf94c20)
The two ASUS WL-330N and WL-330N3G had the
reset keycode assigned to the WPS button. This patch
changes all three devices to use KEY_WPS_BUTTON in
the hopes that this fixes unwanted restarts/
unexpected behavior from the users point of view.
[dropped RG21S]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit ad65d9d7b2)
All buttons on the Netgear R6220 are active-low while they are flagged
as active-high.
The GPIO status reads the following for no buttons pressed:
root@64367-r6220:~# cat /sys/kernel/debug/gpio
gpio-7 ( |wps ) in hi
gpio-8 ( |wifi ) in hi
gpio-14 ( |reset ) in hi
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f7f9fe5256ebb660d3160452c3c01a9eb080938f)
The 2.4 GHz radio had very poor signal reception (-89 dBm for an AP
sitting 5 m away). By enabling the external amplifier, received signal
has improved to -50 dBm for the same AP.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit e667d6f46b)
So far, WiFi MAC addresses for this device have been set up from
caldata. However, this returns values which do not look like MAC
addresses. They also do not match stock firmware:
wlan0 (5.0): 00:11:22:00:17:D0 from 0x8004
wlan1 (2.4): 00:11:22:00:17:CD from 0x4 (and 0x2e)
It looks like the only valid MAC address on this device is at 0x28.
So, this patch changes setup to calculate addresses based on the
value at 0x28:
lan: *:0A (flash, label)
wan: *:0B (flash + 1)
wifi2: *:0A (flash)
wifi5: *:0C (flash + 2)
Thanks to Roger Pueyo Centelles <roger.pueyo@guifi.net> for
investigating this on his devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d1072096f4)
Memory auto-detection for mt7621 has just been added to 19.07
stable branch.
This removes the memory node for the ZBT-WE1326, which will support
revision 5 that has 256MiB RAM (Nanya NT5CC128M16IP-DI) instead of
512MiB (up to revision 4).
ref: #1930
This is taken from master commit a2c19f1d2f ("ramips: dts: drop
memory nodes"), where _all_ memory nodes were removed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This backports the only non-cosmetic fix from 6640e1c368
("ramips: clean and improve MAC address setup in 02_network").
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit switches the default trigger for the WiFi LED from a netdev
trigger on "wlan0" to a wireless-phy based trigger. THis allows the LED
to work, even when the wireless interface is not named "wlan0" without
modifiying the LED settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit fa46c9b208)
SoC: MediaTek MT7621AT
RAM: 128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi: MediaTek MT7603EN bgn 2SS
WiFi: MediaTek MT7612EN nac 2SS
BTN: Reset - WPS
LED: - Power
- LAN {1-4}
- WAN
- WiFi 2.4 GHz
- WiFi 5 GHz
- USB
UART: UART is present next to the Power LED.
TX - RX - GND - 3V3 / 57600-8N1
3V3 is the nearest one to the Power LED.
Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
> tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>
Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
> scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
> mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
> reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 14e0e4f138)
Specifications:
- SoC: MT7628DAN (MT7628AN with 64MB built-in RAM)
- Flash: 8M SPI NOR
- Ethernet: 5x 10/100Mbps
- WiFi: 2.4G: MT7628 built-in
5G: MT7612E
- 1x miniPCIe slot for LTE modem (only USB pins connected)
- 1x SIM slot
Flash instruction:
U-boot has a builtin web recovery page:
1. Hold the reset button while powering it up
2. Connect to the ethernet and set an IP in 192.168.1.0/24 range
3. Open your browser and upload firmware through http://192.168.1.1
Note about the LTE modem:
If your router comes with an EC25 module and it doesn't show up
as a QMI device, you should do the following to switch it to QMI
mode:
1. Install kmod-usb-serial-option and a terminal software
(e.g. minicom or screen). All 4 serial ports of the modem
should be available now.
2. Open /dev/ttyUSB3 with the terminal software and type this
AT command: AT+QCFG="usbnet",0
3. Power-cycle the router. You should now get a QMI device
recognized.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Support for D-Link DWR-118 A1 was added before LEDs feature
in mt76x0e driver.
This fixes the 5GHz WiFi LED which was previously inverted.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and
having a different casing. This adds a new cleaned up R6220.dtsi with the
common bits for both devices. Both devices now have feature parity.
Performed cleanup:
* generic DTS node names
* regulator for usb power
* added missing pinctrl groups
* use switch port instead of VLAN as trigger for WAN LED
Fixes for WNDR3700v5:
* all LEDS work
* correct ethernet MAC addresses
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
- SoC: MediaTek MT7628AN
- Flash: 16MB (Winbond W25Q128JV)
- RAM: 64MB
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200
- Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN)
- WIFI0: MT7628AN 2.4GHz 802.11b/g/n
- WIFI1: MT7612EN 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable power-LED (two-colored, yellow/blue)
Non-programmable internet-LED (shows WAN-activity)
- Buttons: Reset
INSTALLATION:
1. Connect to the serial port of the router and power it up.
If you get a prompt asking for boot-mode, go to step 3.
2. Unplug the router after
> Erasing SPI Flash...
> raspi_erase: offs:20000 len:10000
occurs on the serial port. Plug the router back in.
3. At the prompt select option 2 (Load system code then
write to Flash via TFTP.)
4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the
Server-IP.
5. Connect your computer to LAN1 and assign it as 192.168.1.2/24.
6. Rename the sysupgrade image to test.bin and serve it via TFTP.
7. Enter test.bin on the serial console and press enter.
Signed-off-by: Markus Scheck <markus@mscheck.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added mt76 compatible]
Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas
Specifications:
MT7628 (580 MHz)
64 MB of RAM (DDR2)
8 MB of FLASH
2T2R 2.4 GHz (MT7628)
2T2R 5 GHz (MT7612E)
3x 10/100 Mbps Ethernet (2 LAN + 1 WAN)
2x external, non-detachable antennas (5dbi)
UART header on PCB (57600 8n1)
7x LED, 2x button
Known issues:
The Power LED is always ON, probably because it is connected
directly to power.
Flash instructions
------------------
Load the ...-factory.bin image via the stock web interface.
Openwrt upgrade instructions
----------------------------
Use the ...-sysupgrade.bin image for future upgrades.
Revert to stock FW
------------------
Warning! This tutorial will work only with the following OEM FW:
WR1000_EU_92.122.2.4987.201806261618.bin
WR1000_US_92.122.2.4987.201806261609.bin
If in the future these firmwares will not be available anymore,
you have to find the new XOR key.
1) Download the original FW from the Cudy website.
(For example WR1000_EU_92.122.2.4987.201806261618.bin)
2) Remove the header.
dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64
3) XOR the new file with the region key.
FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D
FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C
You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this:
xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767..
Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!):
https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false)
4) Check the resulting decrypted image.
Check if bytes from 0x20 to 0x3f are:
4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Alternatively, you can use u-boot's tool dumpimage tool to check
if the decryption was successful. It should look like:
# dumpimage -l stock-firmware.bin
Image Name: Linux Kernel Image
Created: Tue Jun 26 10:24:54 2018
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 4406635 Bytes = 4303.35 KiB = 4.20 MiB
Load Address: 80000000
Entry Point: 8000c150
5) Flash it via forced firmware upgrade and don't "Keep Settings"
CLI: sysupgrade -F -n stock-firmware.bin
LuCI: make sure to click on the "Keep settings" checkbox
to disable it. You'll need to do this !TWICE! because
on the first try, LuCI will refuse the image and reset
the "Keep settings" to enable. However a new
"Force upgrade" checkbox will appear as well.
Make sure to do this very carefully!
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added wifi compatible, spiffed-up the returned to stock instructions]
Specification:
CPU: MT7628 580 MHz. MIPS 24K
RAM: 128 MB
Flash: 32 MB
WIFI: 802.11n/g/b 20/40 MHz
Ethernet: 5 Port ethernet switch
UART: 2x
Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART0 line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
set device and tftp server IP address and input the firmware
file name. U-boot will then load the firmware and write it into
the flash.
5. After firmware is started connect via ethernet at 192.168.1.1
Signed-off-by: Liu Yu <f78fk@live.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the
following specifications:
- MT7620A (580 MHz)
- 128MB RAM
- 32MB of flash (SPI NOR)
- 5x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus)
- 2x SIM card slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 10x LEDs (4 GPIO-controlled)
- 1x reset button
The following have been tested and working:
- Ethernet switch
- wifi
- miniPCIe slot
- USB port
- microSD slot
- sysupgrade
- reset button
Installation and recovery:
In order to install OpenWRT the first time or recover the router, you
can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address. Upload the firmware to start the recovery
process.
How to swap SIMs:
You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio13/value. In order for the change to take effect,
you can either use AT-commands (AT+CFUN) or power-cycle the modem (write
0/1 to /sys/class/gpio/gpio14/value).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed
specifications are:
- MT7620A (580MHz)
- 64MB RAM
- 16MB of flash (SPI NOR)
- 6x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM
SIM7100E LTE modem.
- 2x SIM slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 1x 5GHz wifi (mt7612)
- 1x reset button
- 1x WPS button
- 3x GPIO-controllable LEDs
- 1x 10 pin terminal block (RS232, RS485, 4 x GPIO)
Tested:
- Ethernet switch
- Wifi
- USB slot
- SD card slot
- miniPCIe-slot
- sysupgrade
- reset button
Installation instructions:
Installing OpenWRT for the first time requires a bit of work, as the
board does not ship with OpenWRT. In addition, the bootloader
automatically reboots when installing an image over tftp. In order to
install OpenWRT on the HDRM200, you need to do the following:
* Copy the initramfs-image to your tftp-root (default filename is
test.bin) and configure networking accordingly (default server IP is
10.10.10.3, client 10.10.10.123). Start your tftp server.
* Open the board and connect to UART. The pins are exposed and clearly
marked.
* Boot the board and press 1.
* Either use the default filename and client/server IP-addresses, or
specify your own.
The image should now be loaded to memory and board boot. If the router
reboots while the image is loading, you need to try again. Once the
board has booted, copy the sysupgrade-image to the router and run
sysupgrade in order to install OpenWRT to the flash.
Notes:
- You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio0/value. In order for the change to take
effect, you can either use AT-commands (AT+CFUN) or power-cycle the
modem (write 0/1 to /sys/class/gpio/gpio21/value).
- RS485 is available on /dev/ttyS0.
- RS232 is available on /dev/ttyS1.
- The name of the ioX-gpios map to the labels on the casing.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[fixed whitespace issue and merge conflict in target.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or
Vocore2.
Specification:
CPU: MT7628 580 MHz. MIPS 24K
RAM: 64 MB
Flash: 8 MB
WIFI: 802.11n/g/b 20/40 MHz
USB: 1x Port USB 2.0
Ethernet: 5 Port ethernet switch
UART: 2x
Installation: Use the installed uboot Bootloader. Connect a serial cable
to serialport 0. Turn power on. Choose the option: "Load system code
then write to Flash via TFTP". Choose the local device IP and the TFTP
server IP and the file name of the system image. After if the
Bootloader will copy the image to the local flash.
Notes: The I2C Kernel module work not correctly. You can send and
receive data. But the command i2cdetect doesn’t work. FS#845
Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com>
[commit subject and message touches, DTS whitespace fixes, wifi LED
rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses,
removed i2c kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: MediaTek MT7628NN
RAM: 64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED: Power - WLAN
BTN: Reset
UART: 115200 8N1
TX and RX are labled on the board as pads next to the SoC
Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
Note: The ethernet port is by default WAN. So you need to connect to
the router via WiFi
2. Navigate to the Update tab on the left side.
3. Select "Local Update"
4. Upload the OpenWrt sysupgrade image.
Note: Make sure you select not to preserve the configuration.
Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
Wait for the LED to flash 5 times.
2. Assign yourself a static IPv4 in 192.168.1.0/24
3. Upload the OpenWrt sysupgrade image at 192.168.1.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
Instead of assigning I2C pins as GPIOs by default, leave it up to the
user whether to install kmod-i2c-mt7621 and use them for hardware I2C
instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add switch definition for the rtl8367b switch to the DTS/DTSi for
the Belkin F9K1109v1 that was mistakenly omitted from the initial
commit.
Fixes: 017ec068e3 (ramips: add support for Belkin F9K1109v1)
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Enable the USB power for the Netgear R6120. Otherwise, no power is
supplied to an attached USB device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware spec:
CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0
Flashing instructions:
Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692
to get the bootloader and unlock firmware.
0. upgrade your router with the telnet firmware via the
firmware upgrade page on the webui.
1. telnet 192.168.11.1 from your PC
2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer
it to the /tmp directory of the router.
3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader
4. turn off the power
5. Push the reset button while turning on the router and
wait until LED start blinking (~10sec.)
6. Connect Ethernet port and goto http://192.168.1.1.
7. Upload the firmware to firmware restore page in webui.
Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
This adds the SPDX license identifier for the NETGEAR EX6150. It was
missed when submitting the original patch.
Signed-off-by: David Bauer <mail@david-bauer.net>
The specific flash chip used (W25Q256FVEM) accepts 50MHz for read
requests and higher for others. 104MHz for fast reads. ramips seems to
be limited to 80MHz based on testing with higher values (no speedup).
Based on upstream commit: 97738374a310b9116f9c33832737e517226d3722
time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s
[test done with backported upstream v4.19 driver[1], for numbers on
stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI
frequency to 80MHz` commit message]
1. https://github.com/openwrt/openwrt/pull/1578
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[expanded note about spi driver version]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The flash chip on the board (Spansion S25FL256SAIF00) is rated to
support at least 50MHz for normal read requests according to the
datasheet. 133MHz for fast reads. However, ramips seems to be limited to
80MHz.
>From testing this, higher values do not improve speeds.
time dd if=/dev/mtdblock3 of=/dev/null bs=64k from
42.82s to 14.09s.
boot speed is also faster:
[ 66.884087] procd: - init - vs
[ 48.976049] procd: - init -
Since spi speed was requested:
[ 3.538884] spi-mt7621 1e000b00.spi: sys_freq: 225000000
CPU is 900MHz:
[ 0.000000] CPU Clock: 900MHz
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[fixed commit message by adding missing 0 in the spi-mt7621 clock output]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7621
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: MediaTek MT7662E bgn 2SS
WiFi: MediaTek MT7662E nac 2SS
BTN: ON/OFF - Reset - WPS - AP/Extender toggle
LED: - Arrow Right (blue)
- Arrow Left (blue)
- WiFi 1 (red/green)
- WiFi 2 (red/green)
- Power (green/amber)
- WPS (Green)
UART: UART is present as Pads on the backside of the PCB. They are
located on the other side of the Ethernet port.
3.3V - GND - TX - RX / 57600-8N1
3.3V is the nearest one to the antenna connectors
Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).
You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash
Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Device specification:
- SoC: RT5350F
- CPU Frequency: 360 MHz
- Flash Chip: Winbond 25Q32 (4096 KiB)
- RAM: 32768 KiB
- 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
- 1x external, non-detachable antenna
- UART (J1) header on PCB (57800 8n1)
- Wireless: SoC-intergated: 2.4GHz 802.11bgn
- USB: None
- 3x LED, 2x button
Flash instruction:
1. Configure PC with static IP 192.168.1.2/24 and start TFTP server.
2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin"
to "kstart_recovery.bin" and place it in TFTP server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
4. Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Vladimir Kot <vova28rus@gmail.com>
[fixed git commit author and whitespace issues in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The WIZnet WizFi630S board is in the miniPCIe form factor.
SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)
Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1). Then get the
sysupgrade image from a tftp server.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The DIR-510L Wireless Router are based on the MT7620A SoC.
Specification:
-MediaTek MT7620A (580 Mhz)
-128 MB of RAM
-16 MB of FLASH
-802.11bgn radio
-1x 10/100 Mbps Ethernet
-2x internal, non-detachable antennas
-UART (J3) header on PCB (57600 8n1)
-1x bi-color LED (GPIO-controlled), 2x button
-JBOOT bootloader
Known issues:
-Ethernet port is used as LAN
-No communication with charger IC. (uart bitbang needed)
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed whitespace issue in 10-rt2x00-eeprom]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
To be able to configure pwms the pwm driver needs to know the number off
cells in the "pwms" property. For this platform this is 2.
Signed-off-by: Micke Prag <micke.prag@telldus.se>
Hardware:
CPU: MediaTek MT7621AT (2x880MHz)
RAM: 512MB DDR3
FLASH: 256MB NAND
WiFi: 2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI: 5GHz 4x4 MT7615 a/n/ac (Needs driver, See Issues!)
USB: 1x 3.0
ETH: 1x WAN 10/100/1000 3x LAN 10/100/1000
LED: Power/Status
BTN: RESET
UART: 115200 8n1
Partition layout and boot:
Stock Xiaomi firmware has the MTD split into (among others)
- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)
Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.
Note uboot's tftp flash install writes the transferred
image to both kernel partitions.
Installation:
Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.
The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:
nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot
Reverting to stock:
The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.
For this we do the following:
fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot
After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.
Issues:
OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.
See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on
MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem.
Specification:
- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 1x detachable antenna (modem main)
- 1x internal antenna (modem div)
- 1x GPS passive antenna (optional)
- 5x LED (all driven by GPIO)
- 1x button (reset)
- UART (4-pin, 2.54 mm pitch) header on PCB
Other:
Default SIM slot is selected at an early stage by U-Boot, based on
'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2
(micro). U-Boot also resets the modem, using #PERST signal, before
starting kernel.
Flash instruction:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the LAN LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
dts: disable port4 and leave it ephy mode because it connect to nothing
switch port5 connected to GE port we use it as wan port
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Device specification:
- SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz
- RAM: 64Mb
- Flash: 8MB (SPI-NOR)
- Ethernet: 10/100/1000 Mbps
- WLAN
Wireless 1: SoC-integrated : 2.4/5 GHz
Wireless 2: 2.4 GHz RT3092L
- LED: 2x USB, WAN, LAN
- Key: WPS, reset
- Serial: 4-pin header, (57600,8,N,1), 3.3V TTL,
GND, RX, TX, V - J12 marking on board
- USB ports: 2 x USB 2.0
Flashing instructions:
Option 1 (from bootloader web)
- Hold reset button on the back of router when plugging
in power (for at-least 10 seconds after plugged in)
- Connect to a Lan port
- Set computer IP to 10.10.10.3
- Go to http://10.10.10.123 in a web browser
- Click the Browse... Button and select the
*squashfs.sysupgrade.bin file then click APPLY
Option 2 (from the stock admin web)
- Go to firmware upgrade
- Upload the **factory** image *initramfs.bin first
- Boot into openwrt
- From Luci web in openwrt upload the *squashfs.sysupgrade.bin
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added v1 to the compatible identifier, added pciid for
the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi
to prepare for a possible F9K1103 patch]
This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n
Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED
Flash instruction:
The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
the router and keep button pressed for around 10 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Marcel Jost <majo@icutech.ch>
* assign pinmux groups to gpio function for LEDs/buttons
* rename flash node to be more generic in line with other device nodes
* remove useless/incorrect eeprom property from wmac node
* correct base mac address for embedded switch
Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
Buffalo WHR-G300N has a LED for power status indication, but it is not
connected to the GPIO and cannot be controlled by the kernel. So,
WHR-G300N uses "ROUTER" LED as the system status LED instead.
This commit changes it to use "DIAG" LED insted of "ROUTER" like
WHR-G301N in ath79 target.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The R6120 has no 5GHz WLAN LED, the assigned GPIO in fact controls
the WAN LED.
Renames the LED accordingly in the device-tree.
Removes the 5GHz WLAN LED trigger.
Adds the correct WAN port LED trigger.
----
Currently, the MAC address for the Netgear R6120 is read from the NVRAM
partition. The offset for the MAC address however is not consistent
across devices or firmware versions.
Switch to using the factory partition like all other Netgear devices do.
----
The LAN ports of the R6120 are labled in reverse on the casing.
Adjust LuCI switchport numbering accordingly.
----
The WiFi eeprom offsets for the R6120 are currently wrong (5GHz offset
is bigger than the partition itself).
Fixes poor performance on 2.4 and 5 GHz.
Signed-off-by: David Bauer <mail@david-bauer.net>
This option was a spi nor hack which is dropped in commit
bcf4a5f474 ("ramips: remove chunked-io patch and set spi->max_transfer_size instead")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [edit message]
