When doing parallel build on a fast machine with bottleneck in i/o,
m_xt.so may start linking faster than dynsyms.list gets populated,
resulting in error:
ld:dynsyms.list:0: syntax error in dynamic list
Fix this by adding dynsyms.list as make dependency to m_xt.so
Described also here:
https://bugs.openwrt.org/index.php?do=details&task_id=3353
Change from v1:
- add dynsysms.list dependancy only when shared libs are enabled
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Fixes: FS#3353
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update busybox to version 1.34.0
* Remove upstreamed patches (205, 530, 540)
* Remove one old patch that does not apply any more. (203)
That was originally introduced in 2008 with 563d23459,
but does not apply after busybox restructuring with
https://git.busybox.net/busybox/commit/networking/udhcp/dhcpc.c?h=1_34_stable&id=e6007c4911c3ea26925f9473b9f156a692585f30
and
https://git.busybox.net/busybox/commit/networking/udhcp/dhcpc.c?h=1_34_stable&id=1c7253726fcbab09917f143f0b703efbd2df55c3
* Refresh config and patches.
* Backport upstream fixes for
- MIPS compilation breakage and
- process substitution regression
Config refresh:
Refresh commands, run after busybox is first built once:
cd utils/busybox/
cd config/
../convert_menuconfig.pl ../../../../build_dir/target-aarch64_cortex-a53_musl/busybox-default/busybox-1.34.0
cd ..
./convert_defaults.pl < ../../../build_dir/target-aarch64_cortex-a53_musl/busybox-default/busybox-1.34.0/.config > Config-defaults.in
Manual edits needed afterward:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt configTARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
BUSYBOX_DEFAULT_UDHCPC_DEFAULT_INTERFACE (just "")
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in : change at "Options common to all shells" the symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
929c862 vm: fix toplevel function call protocol
8f34d70 fs: fix chown() and rename() error return values
03ca445 tests: disable fuzz tests for now
3b1be3d types: mark further GC roots
d49af4e types: fix comparison of differently signed integers
c79ff39 types: handle conversion errors when dealing with negative error indexes
3315b1f types: allow negative array indexes
d5b25f9 treewide: harmonize function naming
cc4ce8d module: remove unused defines
f5d7526 examples: add libucode usage examples
559eff2 types, vm: adjust GC api
e5e7e62 treewide: move header files into dedicated directory
ff6168a build: install header files
7e6ce0f main: introduce new flag `-x` to allow disabling specific functions
b1817b3 vm: fix invalid memory access on GC'ing uninitialized VM context
498fe87 main: refactor option parsing and VM setup
ff52440 treewide: consolidate typedef naming
1d60418 vm: add API to control trace mode
48f33ad vm: make root exception handler configurable
0f69f09 vm: fix invalid memory access on toplevel function calls
6bcc318 vm: fix handling exceptions in top-level function calls
4ae0568 lib, vm: reimplement exit() as exception type
2f77657 vm: extend API to allow returning result value from VM execution
111645a vm: remove module preloading logic
38ff6de main: preload modules ourselves
d5bc223 vm: add uc_vm_invoke() helper
ef0baf1 vm: cosmetic fix for outputting exceptions without source context
b11a2fa vm: move global scope allocation into uc_vm_init()
900b2a3 vm: add getter and setter for vm globals scope
0179576 lib: rename uc_add_proto_functions() to uc_add_functions()
98b9c84 lib: expose stdlib function array
1adfba0 treewide: eliminate dead code and unused functions
3974e71 treewide: replace a number of unnecessary type casts
bf85226 treewide: move ressource type registry into vm instance
e2b3d2e build: split into libucode and ucode cli
dad8f3a types: properly deal with circular data in GC mark phase
62dbd64 lexer: rename UT_ prefixed constants to UC_
bc8e465 types: fix wrong assert() on tearing down object trees
853b9f1 vm: fix potential invalid memory access in uc_vm_get_error_context()
6f05cdd lib: fix refcount imbalance in uc_require_path()
96f140b lib, vm: ensure that require() compiles modules only once
df5db5f compiler: don't segfault on invalid declaration expressions
a97c7a1 lexer: transition into EOF state on unrecognized character
2a838d1 compiler: improve mapping of binary operator tokens to instructions
9872f65 vm: add support for I_LE and I_GE instructions
4e410c3 treewide: let uc_cmp() use instruction instead of token numbers
ce6081d lexer, vm: reorder token and instruction numbers
234a4f6 lib: implement b64enc() and b64dec() functions
856a0c0 lib: only consider context of calling function for callbacks
86fb130 lib: implement min() and max() functions
3e893e6 lib: pass-through "this" context to library function callbacks
42de7ab lib: implement `sourcepath()` function
05c80a7 lib: fix negative uc_index() return value on 32bit systems
9874562 lexer: implement raw code mode
3b665c8 lexer: drop value union from keyword table
44354cf lexer, compiler: separate TK_BOOL token into TK_TRUE and TK_FALSE tokens
5879bdf syntax: drop Infinity and NaN keywords
d4edadc lib: rename uc_lib_init() to uc_load_stdlib()
d81bad7 main, lib: move allocation of globals object into lib function
c4f4b38 main: simplify REQUIRE_SEARCH_PATH initialization
54ca3aa types: fix uninitialized memory on setting non-contiguous array indexes
cbc0d78 build: let require search patch default to CMAKE_INSTALL_PREFIX
5714705 syntax: introduce `const` support
ed32c42 compiler, lexer: add NO_LEGACY define to disable legacy syntax features
ff6811f syntax: implement `delete` as proper operator
5803d86 lib: implement wildcard() function
dfb7379 fs: implement chmod(), chown(), rename() and glob() functions
1ddf5b6 lexer: skip interpreter line in any source buffer
9951a00 build: lower minimum required CMake version to v3.13
7b81ab2 main: expose argv as global ARGV array to ucode scripts
7283a70 tests: rename misnamed testcases for consistency
3f80116 compiler: fix local for-loop initializer variable declarations
f20b56f compiler: properly parse slashes in parenthesized division expressions
5c4e1ea lib: implement regexp(), a function to construct regexp instances at runtime
e546bba lib: implement render(), an include variant capturing output in a string
0cb10c6 vm: implement mechanism to change output file descriptor
eb8a64d lib: fix uc_sort()
f1ffc9f vm: truncate long values after 60 chars in trace output
850612f compiler: properly handle break/continue in nested scopes
f0a9875 compiler: properly handle keyword in parenthesized property access expression
1660433 compiler: fix stack mismatch on compiling `use strict` statements
a36e0df syntax: implement support for 'use strict' pragma
827a34a vm, compiler: get rid of unused struct members
594cdf3 lib: implement assert()
c4d1648 lib: add support for pretty printing JSON to printf() and sprintf()
f2eaea3 lib: gracefully handle truncated format strings in uc_printf_common()
02629b8 lexer: fix infinite loop on parsing unterminated comments
2bc9bac lexer: fix infinite loop on parsing unterminated expression blocks
f73e201 lexer: fix infinite loop when parsing regexp literal at EOF
86b4863 compiler: fix segfault on parsing invalid pre/post increment expressions
0e24509 lib: fix reporting source context lines at EOF
e66b2ad compiler, lexer: improve lexical state handling
e29b574 lib: fix uc_split() quirks
64eec7f treewide: ISO C / pedantic compliance
4af803d build: output error messages on test failures
9ef693e vm: improve context for early errors
6def9fc tests: pass ucode library path through environment
d5dd183 treewide: address various sign-compare warnings
28825ac types: support creating ressource values without associated type
9c5106a types: fix potential memory leaks and null pointer accesses
c51934a types: fix potential leak of key in ucv_object_add()
7b28727 main: fix ineffective EOF check in parse()
4cf897c lib: uc_system(): fix invalid free() of non-heap memory
35af4ba treewide: rework internal data type system
f2c4b79 treewide: fix issues reported by clang code analyzer
93ededb tests: allow executing run_tests.sh from any directory
0e4a387 Add initial GitLab and GitHub CI support
df73b25 tests: add more tests
41d33d0 tests: custom: return exit code if tests fails
1c548a6 cmake: do not output binaries into lib directory
2b59097 tests: create custom tests from current tests cases
8039361 main: provide just binary name in help output
778e4f7 lexer: fix incomplete struct initializers
502ecdc cmake: enable extra compiler checks
3c2aeff cmake: fix includes and libraries
617a114 cmake: make 3.0 minimum version
f360350 lib: implement sleep(ms) function
7f0ff91 lib: allow parsing non-array, non-object value in json()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Change the CONFLICTS definition from the alternative package
(ethtool-full) to the main one.
The CONFLICTS line creates a dependency to the conflicting package.
Right now, the dependency would be created in the PACKAGE_ethtool-full
symbol:
config PACKAGE_ethtool-full
depends on m || (PACKAGE_ethtool != y)
When the main package is selected by airmon-ng, it selects
PACKAGE_ethtool, *depending* on the value of PACKAGE_ethtool-full:
config PACKAGE_airmon-ng
select PACKAGE_ethtool if PACKAGE_ethtool-full<PACKAGE_airmon-ng
In the first block, the value of PACKAGE_ethtool-full depends on the
value of PACKAGE_ethtool. In the second block, the opposite is true:
the value of PACKAGE_ethtool depends on the value of
PACKAGE_ethtool-full. This is a recursive dependency.
Fix it by changing the package where the dependency is created, so that
only the value of PACKAGE_ethtool will depend on PACKAGE_ethtool-full.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The previous procd update broke mounting overlayfs in an attempt to
fix an off-by-one error. Revert that broken fix and apply fix from
Nick Hainke <vincent@systemli.org> instead to bring things back to
life.
20adf53 Revert "initd: fix off-by-one error in mkdev.c"
773e8da initd: fix off-by-one error in mkdev.c
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove old math patch meant for old GCC versions. It's not needed
for GCC and causes issues with clang.
Add CMake patch to identify clang properly and apply the proper
flags. Fixes the following warnings/errors:
json_pointer.c:230:7: warning: implicit declaration of function
'vasprintf' is invalid in C99 [-Wimplicit-function-declaration]
rc = vasprintf(&path_copy, path_fmt, args);
^
json_pointer.c:317:7: warning: implicit declaration of function
'vasprintf' is invalid in C99 [-Wimplicit-function-declaration]
rc = vasprintf(&path_copy, path_fmt, args);
^
/usr/include/bits/mathcalls.h:177:23: error: cannot redeclare builtin
function '__builtin_isinf'
__MATHDECL_ALIAS (int,isinf,, (_Mdouble_ __value), isinf)
^
/usr/include/bits/mathcalls.h:177:23: note: '__builtin_isinf' is a
builtin with type 'int ()'
/usr/include/bits/mathcalls.h:213:23: error: cannot redeclare builtin
function '__builtin_isnan'
__MATHDECL_ALIAS (int,isnan,, (_Mdouble_ __value), isnan)
The clang patch is an upstream backport.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
df251c2 uxc: move mountpoint of persistent config to /var/run/uxc
e5b38fd trace: free memory allocated by blobmsg_format_json_indent()
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The hostapd.sh script already has support for configuring proxy-ARP,
however no built variant has support for it enabled.
Enable proxy-ARP support for hostapd-full builds in order to allow users
to actually use this feature.
Signed-off-by: David Bauer <mail@david-bauer.net>
The disable_dgaf config fiels is only available in case Hostapd is
compiled with Hotspot 2.0 support, however Proxy-ARP does not depend on
Hotspot 2.0.
Only add the code related to this config field when Hotspot 2.0 is
enabled to fix compilation with the aformentioned preconditions.
Signed-off-by: David Bauer <mail@david-bauer.net>
This version fixes two vulnerabilities:
- SM2 Decryption Buffer Overflow (CVE-2021-3711)
Severity: High
- Read buffer overruns processing ASN.1 strings (CVE-2021-3712)
Severity: Medium
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
OpenWrt's special gpio-button-hotplug driver is still using
exclusively the legacy GPIO Subsystem gpio_ API.
While it still does work fine for most devices, upstream
linux is starting to convert platform support like that of
the APU2/3/4 to the new GPIOD LOOKUP tables that are not
supported by it.
Hence, this patch replaces the gpio_ calls present in
gpio-button-hotplug with gpiod_ equivalent wherever
it's possible. This allows the driver to use the
gpiod lookup tables and still have a fallback for
legacy platform data code that just sets button->gpio
set to the real button/switch GPIO.
As a bonus: the active_low logic is now being handled
by the linux's gpio subsystem too. Another issue that
was address is the of_handle leak in the dt parser
error path.
Tested with legacy platform data: x86_64: APU2, MX-100
Tested on OF: ATH79; MR18, APM821xx: Netgear WNDR4700,
RAMIPS: WL-330N3G
LANTIQ: AVM FritzBox 7360v1
Reported-by: Chris Blake <chrisrblake93@gmail.com>
Tested-by: Chris Blake <chrisrblake93@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This integrates with netifd in order to provide STP/RSTP protocol support
in user space. It defaults to using RSTP for bridges with stp enabled.
This daemon has no config files, it uses the configuration passed from
netifd via ubus
Signed-off-by: Felix Fietkau <nbd@nbd.name>
50e6b20 libfstools: handle open() return value properly in F2FS check
e1b6811 blockd: include missing libubox/utils.h
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
8a8306d uxc.c: fix coverity resource leak warning
7f2398e jail: devices: create parent folder when creating devices
0603c8d jail: return to hook callback instead of just calling it
3edb7eb jail: check return value when opening console
af048a3 jail: use portable sizeof(void *)
6010bd3 utils: make sure read() string is 0 terminated
f6daca3 uxc: free string returned by blobmsg_format_json_indent()
51f1cd2 trace: free string returned by blobmsg_format_json_indent()
d716cb5 trace: handle open() return value and make sure string is terminated
b824a89 jail: preload: avoid NULL-dereference in case things go wrong
167dc24 jail: protect against strcat buffer overflows
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
94170ae24bc9 device: extend device settings flags to 64 bit
1eb0fafaa986 device: add support for configuring device link speed/duplex
ed84473b7af9 bridge: memset bst->config by default to avoid stale config values
6519cf31e4b0 bridge: add support for an external STP daemon
454e9c33c906 bridge: tune default stp parameters
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a config option for json_script instead of unconditionally including
all json files in /etc/uhttpd in every uhttpd instance. This makes it
possible to configure a single instance with an unconditional redirect,
which currently renders all other uhttpd instances unusable.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
01b4e60 dhcpv4: fix uninitialized hostname in some ubus events
1666769 dhcpv6-ia: allow up to 64 bit wide hostid
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The option was initially named TARGET_ROOTFS_LN_VAR_TMP, and the check
was correct. When renaming the option to something more suitable, the
check was changed to check for n, but when an option is not set, it's
not n but empty. This results in the check always evaluating to false.
Fix the check by checking for y with ifneq.
Fixes: 57807f50de ("base-files: add option to make /var persistent")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
In OpenWrt, /var is symlinked to /tmp by default. This is done to reduce
the amount of writes to the flash chip, which often have not the
greatest durability. As a result, things like DHCP or UPnP lease files,
are not persistent across reboots.
Since OpenWrt can run on devices with more durable storage, it makes
sense to have an option for a persistent /var. Add an option to make
/var persistent. When enabled, /var will no longer be symlinked to /tmp,
but /var/run will be symlink to /tmp/run, as it should contains only
files that should not be kept during reboot. The option is off by
default, to maintain the current behaviour.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The userspace application now uses the model=full option to match the
configuration of the kernel module. The source no longer contains SOAP
support, which was the primary reason to build only typical instead
of full before.
This makes several CLI commands, which were already supported in the
kernel module, available in the userspace application. For example, this
includes bbsg which allows to get information about VDSL2 bands.
Some previously applied build options were redundant. Disabling ADSL MIB
support is unnecessary, as it only applies to Danube. ADSL LED support
is no longer included in the source. ReTx counters are already included
with model type full.
This increases the size of the userspace application by approximately
15 kB (uncompressed). The kernel module does not change at all.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
with xinetd allowed+blocked (ipv6) hosts could be set
what is not possible with stock dropbear package
The file size increased 12 Bytes, so this "opimisation" did not really helped.
Within a compressed storage format it is 0..
ipk: 111.171 -> 111.361 = 190 bytes
bin: 215.128 -> 215.140 = 12 bytes
Signed-off-by: Fritz D. Ansel <fdansel@yandex.ru>
Replace some OpenWrt patches with openembedded ones for easier
maintainability. Remove several outdated ones as well.
Replace PKG_RELEASE with AUTORELEASE to avoid manual bumps.
Remove !arc dependency as it is supported upstream now.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
BananaPi BPi-R2 comes with HDMI and MIPI-DSI. Use dislpay facility in
Linux by add "console=tty1" boot argument.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes a build problem seen after binutils 2.36 is used by default.
Fixes: 3f41153b1c ("toolchain/binutils: switch to version 2.36.1 by default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
592ac0f add a note
4bacd14 sslcertfile: list /etc/ssl
7bdefa4 example: indicate that skip is an option
d1e9a85 wifi: sys pipe usage
eb903e1 README: add note about policycoreutils-setfiles weak dependency
762e011 ttyd: signull all subjects
fbfc079 acme: add basic support for acme_cleanup.sh and acme_setup.sh
9ac7592 acme: transition to sys.subj on generic initscript execution
f3dd1ba acme: missing rules related to sys.subj trans on file.initscriptfile
ae273fa odhcp6c/netifd: support drop-in directories
5fa9b41 subj: do not encourage misconfiguration
44722b6 blockd, logd, odhcpc6, ubiutil, mtdstordev
a775d93 21.02 related
a473691 rcboot runs rcuhttpd which creates /tmp/etc for /tmp/etc/uhttpd
290e9fb rcuhttpd: related to rcboot and uci-defaults
3fc0d8b rcuhttpd: lists /etc/uci-defaults
1f5ef48 removes ubvol.lock policy and adds move mtd/ubi partitions
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Installing headers and static libraries to the target system seems
to be not required for most use cases, so let's factor them
out into a dedicated -dev package.
This cuts down to disk usage to around 50% of the original
package to ~ 2MB - not that disk space is an issue normally,
but when using inside an initramfs only project, it counts.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
When compiling busybox with GCC 10 and CONFIG_PKG_ASLR_PIE_ALL=y, there
are hundreds of errors like:
relocation R_MIPS16_26 against `xzalloc' cannot be used when making a
shared object; recompile with -fPIC
Simply solve this by no longer disabling PKG_ASLR_PIE, so that $(FPIC)
is properly added to the CFLAGS and LDFLAGS.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
While an image layout based on MBR and 'bootfs' partition may be easy
to understand for users who are very used to the IBM PC and always have
the option to access the SD card outside of the device (and hence don't
really depend on other recovery methods or dual-boot), in my opinion
it's a dead end for many desirable features on embedded systems,
especially when managed remotely (and hence without an easy option to
access the SD card using another device in case things go wrong, for
example).
Let me explain:
* using a MSDOS/VFAT filesystem to store kernel(s) is problematic, as a
single corruption of the bootfs can render the system into a state
that it no longer boots at all. This makes dual-boot useless, or at
least very tedious to setup with then 2 independent boot partitions
to avoid the single point of failure on a "hot" block (the FAT index
of the boot partition, written every time a file is changed in
bootfs). And well: most targets even store the bootloader environment
in a file in that very same FAT filesystem, hence it cannot be used
to script a reliable dual-boot method (as loading the environment
itself will already fail if the filesystem is corrupted).
* loading the kernel uImage from bootfs and using rootfs inside an
additional partition means the bootloader can only validate the
kernel -- if rootfs is broken or corrupted, this can lead to a reboot
loop, which is often a quite costly thing to happen in terms of
hardware lifetime.
* imitating MBR-boot behavior with a FAT-formatted bootfs partition
(like IBM PC in the 80s and 90s) is just one of many choices on
embedded targets. There are much better options with modern U-Boot
(which is what we use and build from source for all targets booting
off SD cards), see examples in mediatek/mt7622 and mediatek/mt7623.
Hence rename the 'sdcard' feature to 'legacy-sdcard', and prefix
functions with 'legacy_sdcard_' instead of 'sdcard_'.
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
procd.sh:
Instead of triggering on every mount.add event, there should be no
mount trigger at all in case none of the directories passed to
procd_add_*_mount_trigger() are located on a mountpoint configured in
/etc/config/fstab.
uxc:
add missing dependency on rpcd.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
040fecc system: fix issues reported by Coverity
48f481b service: make sure string read is null terminated
16dbc2a uxc: fix a bunch of issues discovered by Coverity
ff9002f uxc: fix help output
104b49d uxc: support config in uvol
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Delete tunnel on 6in4 interface teardown.
Should solve problem related to tunnel stuck on restart loop
with "Unknown Command" on tunnel restart due to wan connection drop.
Fixes: FS#3690
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Add --disable-libdebuginfod with remove libcurl dependency.
Remove totally unused host elfutils.
Refreshed and rebased patches.
Also happens to fix compilation with GCC11.
Newer versions of elfutils seem to have some kind of dependency on
obstack.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
When using htmode 'HE20' with a radio mode that uses wpa-supplicant
(like mesh or sta), it will default to 40 MHz bw if disable_ht40 is not
set. This commit fixes this behaviour.
Signed-off-by: Jesus Fernandez Manzano <jesus.manzano@galgus.net>
This enables building of rpcapd and adds it as a package.
It is a daemon that allows remote packet capturing from another machine.
E.g. Wireshark can talk to it using the Remote Capture Protocol (RPCAP).
https://www.tcpdump.org/manpages/rpcapd.8.html
Compile and run tested: OpenWrt SNAPSHOT r17190-2801fe6132 on x86/64
Signed-off-by: Stephan Schmidtmer <hurz@gmx.org>
When having two keys that start with the same characters and the second
key just has one character more nand_tffs_read and tffs_read return the
wrong value for the longer key. This is due to the usage of strncmp in
combination with the length of the shorter key which is usually first in
the list before the longer key and when strncmp matches, the search is
stopped. The problem only occurs when the length of the two keys is
different, not if just the last character is different. The fix is to
use strcmp and as such it will only return the value if the key (name)
and the key to look for (namefilter) have the same value and length. A
sample case returning wrong values is when keys macwlan and macwlan2 are
defined and querying macwlan2 returns the value for macwlan.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This increases the size of the iw_5.9-8fab0c9e-3_mips_24kc.ipk from
41166 to 41942 bytes by 776 bytes.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Change procd_add_start_mount_trigger to procd_add_restart_mount_trigger
and make it call 'restart' instead of 'start'.
This is more useful as it allows to handle both cases, intial start of
a services as well as restarting services. Calling 'restart' on a
service which has not yet been started has the same result as calling
'start'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add a generic sdcard upgrade method instead of duplicating code in yet
another target, and add a feature flag to only install this upgrade
method in targets that set this flag. Copied from mvebu.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The xfrm_interface module will not be built if IPv6 is not enabled in
the kernel. Add this dependency in the kmod package to avoid people
wondering why it doesn't build when they disabled IPv6.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
e10de28 jail: cgroups-bpf: fix compile with musl 1.2
f5d9b14 hotplug-dispatch: fix rare memory leaks in error paths
Add new init script helpers:
procd_add_start_mount_trigger
procd_add_reload_mount_trigger
procd_get_mountpoints
Both trigger helpers expect a list of paths which are checked against
the mount targets configured in /etc/config/fstab and a trigger for all
mountpoints covered by the list of paths is setup.
procd_get_mountpoints is useful to find out if and which mountpoints
are covered by a list of paths.
Example:
DATADIRS="/mnt/data/foo /mnt/data/bar /etc/foo/baz /var/lib/doe"
start_service() {
[ "$_BOOT" = "1" ] &&
[ "$(procd_get_mountpoints $DATADIRS)" ] && return 0
procd_open_instance
# ...
procd_close_instance
}
boot() {
_BOOT=1 start
}
service_triggers() {
procd_add_start_mount_trigger $DATADIRS
}
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Netlink support is required for using the virtual cable tester
functionality.
Remove the pretty print build option and instead create a second package
variant ethtool-full. This allows users to install the full ethtool
featureset using opkg.
Signed-off-by: David Bauer <mail@david-bauer.net>
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Fix build on glibc targets and address a bunch of compiler warnings.
93fc089 jail: cgroups-bpf: don't use sys/reg.h when building with glibc
548d057 jail: don't ignore return value of seteuid()
220b716 jail: ignore return value when creating default /dev symlinks
78d5baa hotplug-dispatch: don't ignore asprintf() return value
736aee5 uxc: always handle asprintf() return value
2b20456 hotplug-dispatch: replace wrongly used assert()
bfc86a2 jail: cgroups: replace wrongly used assert()
516bdf2 jail: don't ignore return value of write()
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Try umount on device mapper and loop devices still mounted, so the
subsequent call to disactivate all physical volumes and delete all
loop devices is more likely to succeed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
141ac85 libblkid-tiny: fix invalid open syscall return check
9e26563 libblkid-tiny: install header file to include dir
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If the busybox applet losetup was selected, `command -v` selects that
during sysupgrade. As this applet is in another path and doesn't cover
the '-D' option which is used to make sure user-defined loop devices
are no longer active during sysupgrade.
Detect losetup at the path of the full utility to avoid error messages
in case of the busybox applet being selected.
Reported-by: fda77 <fda77@users.noreply.github.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
EXTRA_MOUNT variable should be reset in dnsmasq_start() rather than
just once at the beginning of the script.
Fixes: ac4e8aa2f8 ("dnsmasq: fix more dnsmasq jail issues")
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* remove superflus mounts of /dev/null and /dev/urandom
* reset EXTRA_MOUNTS at the beginning of the script
* add mount according to ignore_hosts_dir
* don't add mount for file which is inside a directory already in the
EXTRA_MOUNTS list
Fixes: 59c63224e1 ("dnsmasq: rework jail mounts")
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* split into multiple lines to improve readability
* use EXTRA_MOUNT for addnhosts instead of blindly adding /tmp/hosts
* remove no longer needed mount for /sbin/hotplug-call
* add dhcp-script.sh dependencies (jshn, ubus)
Fixes: 3a94c2ca5c ("dnsmasq: add /tmp/hosts/ to jail_mount")
Fixes: aed95c4cb8 ("dnsmasq: switch to ubus-based hotplug call")
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
46d02c2 block: don't add non-ubifs ubi devices
cc63933 blockd: send mount.ready when startup has completed
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CZ.NIC as part of Turris project released free and open source WTMI
application firmware wtmi_app.bin for all Armada 3720 devices.
This firmware includes additional features like access to Hardware
Random Number Generator of Armada 3720 SoC which original Marvell's
fuse.bin image does not have.
Add a patch which allows to pass the commit id, so the firmware is able
to identify itself, see a04bffeb.
Add a patch to disable linking with gold, since the ARM toolchain
doesn't ship gold.
Cherry-pick the 3 post-release fixes.
Signed-off-by: Andre Heider <a.heider@gmail.com>
02e23db fix compilation errors popped up by GCC-10
7c35173 Merge pull request #29 from pali/sync-a38x-uboot
bb734f5 mv_ddr: a38x: Use SOC_REGS_PHY_BASE for INTER_REGS_BASE
ee1ea84 mv_ddr: a38x: Fix ddr3 compilation
70f3e2e mv_ddr: Fix comment typo
dd960b4 mv_ddr: ddr3: Allow boards to specify CK_DELAY parameter
a87f4f7 mv_ddr: ddr3: only use active chip-selects when tuning ODT
3defcec mv_ddr: a38x: Add support for setting timing in hws_topology_map
Signed-off-by: Andre Heider <a.heider@gmail.com>
2efdb10 wtmi: Fix calculation of UART divider
4247e39 fix: twin die ddr porting guide
8ad7992 sys_init: Add missing newlines in debug mode
4ddea19 avs: Validate VDD value from OTP
c444aeb avs: Fix description for avs value 0x2e
1915b78 tim: Optimize code generated by gettimver.sh and print newline
21f566d tim: Print mv_ddr version and configuration on UART
840b70b tim: Use variable $DDRFILE where possible
c10e6ae tim: Fix waiting for UART TX ready
7bf95cf wtmi: Wait 3ms for the TX on UART to be empty prior resetting TX FIFO
63e8433 wtmi: Add "dirty" suffix to git commit and rebuild sys_init.bin binary when VERSION changes
e949b58 wtmi: During setup clock phase print CPU and DDR speed
10376b5 wtmi: Flush output on UART after the '\n' character
509c647 Makefile: Check that specified DDR_TOPOLOGY option is valid
Signed-off-by: Andre Heider <a.heider@gmail.com>
Revert to using the checked in `tbb_linux` image tool binary since building
it drags in the rather big Crypto++ project.
Cherry-pick the post-release UART fixes.
Switch to AUTORELEASE while at it.
Signed-off-by: Andre Heider <a.heider@gmail.com>
From version 2021.09 U-Boot will fixup Turris Omnia's DTB before
booting, separating U-Boot's environment into separate MTD partition
"u-boot-env" [1].
Check if "u-boot-env" MTD partition exists and set the uci defaults
accordingly.
[1] https://lists.denx.de/pipermail/u-boot/2021-July/455017.html
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Some devices (such as Extreme Networks WS-AP3959i-ROW) do not contain
precal binaries in ART, and the precal in the cards eeprom causes
firmware load errors.
These firmware files were previously in linux-firmware,
so these are adding them back and renaming to be cleaner.
Signed-off-by: Damien Mascord <tusker@tusker.org>
Add a patch to fix building with GCC 11, which triggers new warnings by
enabling -Warray-parameter by default.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
85f01c44a950 bridge: check bridge port vlan membership on link-up events
17e453bd68b4 wireless: add back regular virtual interfaces on hotplug-add events as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
772292e uxc: don't restart containers when mount shows up
3a9d910 uxc: resolve volume UUIDs by name of UCI fstab section
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
a846c6b blockd: fix length of timeout int passed to ioctl
1d681ca block: support umount device basename
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
59f7c11 blockd: create mountpoint parent folder if needed
9cc96af Revert "block: resolve /dev/mapper/* name for /dev/dm-0 when hotplugging"
06334ac Revert "blockd: detect mountpoint of /dev/mapper/*"
9ab3551 block: use /dev/dm-* instead of /dev/mapper/*
5114595 block: allow remove hotplug event to arrive at blockd
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When the kmod-qlcnic package is built on targets that have
CONFIG_PCI_IOV enabled, the CONFIG_QLCNIC_SRIOV symbol is exposed.
Enable this symbol in the kmod package to fix its build.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
As the board name was changed to be identical to the device tree
compatible string (just like for other boards), also reflect that
change for U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add fw_env configuration for the BPi-R2 which is a mediatek/mt7623
devboard which can be booted from SD Card or eMMC.
Auto detect the boot device and add environment accordingly.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All mediatek boards having fw_env accessible through uboot-envtools
belong to be mt7622 subtarget. Move the file, as subtarget-specific
files are supported for a while now.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* use built-in default environment instead of file in bootfs
* get rid of bootfs alltogether and use uImage.FIT
* auto-detect boot device like original script did
* add support for factory button
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
of_platform_device_create require CONFIG_OF selected.
Add an ifdef and register to the of platform only if of is available.
Fixes: 985954ccbd ("kernel: add ath10k support for of_get_mac_address")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
ath10k doesn't currently support the standard function to get mac-address from the dts.
Add this for both ath10k and ath10k-ct
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Programs like the olsr-name-plugin write hostname files to "/tmp/hosts/".
If you don't add this to the jail_mount, dnsmasq can't read it anymore.
Signed-off-by: Nick Hainke <vincent@systemli.org>
0ee73b2 uxc: implement support for rootfs overlay in containers
b0a8ea1 jail: do not hack /etc/resolv.conf on container rootfs
92aba53 jail: increase max additional env records to 64
15997e6 jail: allow rootfs to be a symbolic link
0114c6f jail: open() extroot folder before mounting
ed96eda uxc: check for required blockd mounts
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This will restart the interface in case the CSA fails and can be used to
force the device on a DFS channel (including full CAC)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
4d4dcfb blockd: detect mountpoint of /dev/mapper/*
2f42515 block: resolve /dev/mapper/* name for /dev/dm-0 when hotplugging
39558a1 blockd: also send ubus notification on mount hotplug
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
f12b073c0cc3 wireless: add some comments to functions
b0d090688302 bridge: fix setting pvid for updated vlans
ff3764ce28e0 device: move hotplug handling logic from system-linux.c to device.c
16bff892f415 ubus: add a dummy mode ubus call to simulate hotplug events
7f30b02013f2 examples: make dummy wireless vif names shorter
013a1171e9b0 device: do not treat devices with non-digit characters after . as vlan devices
f037b082923a wireless: handle WDS per-sta devices
db0fa24e1c17 bridge: fix enabling hotplug-added VLANs on the bridge port
4e92ea74273f bridge: bring up pre-existing vlans on hotplug as well
1f283c654aeb bridge: fix hotplug vlan overwrite on big-endian systems
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ! Behavior change !
Old behavior: If the Reset button is held down during power-on
do factory reset and try booting recovery from TFTP forever.
If valid recovery is received via TFTP, write it to flash and boot.
New behavior: If the Reset button is held down during power-on
do factory reset, then try TFTP *once*, then try booting on-flash
recovery, then keep trying via TFTP forever until a valid image is
received.
Only if there is no bootable recovery stored on flash, store the
downloaded recovery. Then boot it.
* Set loadaddr to 0x48000000 in order to allow booting images larger
than ~47MB (reported by Oskari Lemmelä). Setting loadaddr to
0x48000000 gives us 384MB on devices with 512MB RAM, which should be
more than enough as a maximum size for uImage.FIT to be loaded.
* Widely unify device-specific default environment in preparation to
auto-generate it from parameters.
* backport upstream commit fixing MBR/DOS partitioning
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0
This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1.
Installation:
Upload the generated factory image through the factory web interface.
(following part taken from EA7300 v2 commit message:)
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
With thanks to Tom Wizetek (@wizetek) for testing.
Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
a0a0e02 iwinfo: rename hardware.txt to devices.txt
Also split common devices.txt (former hardware.txt) into a common
libiwinfo-data package to allow different libiwinfo versions to
coexist without file clashes.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Imports a function from iw to convert frequencies to channel numbers.
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
[fix potential out of bounds read]
Signed-off-by: David Bauer <mail@david-bauer.net>
'--local' is a synonym for '--server' so let's use '--local' in the
resultant config file for uci's 'local' instead of uci's local
parameter being turned into '--server'. Slightly less confusion all
round.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Drop support for building the obsolete broadcom-wl backend and always
forcibly enable the nl82011 support. This allows us to make the package
shared again since no target specific compilation is happening anymore.
This will solve various repository coherency issues related to unavailable
libiwinfo versions in the long run.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This partially reverts changes done in commit 72cc44958e ("treewide:
mark selected packages nonshared") as it removes the nonshared flag, but
keeps the PKG_RELEASE as the PKG_RELEASE bump while adding nonshared
flag was incorrect.
Unmark uci, ubus, libubox, lua, libnl-tiny and libjson-c as nonshared
packages as this fix attempt didn't worked out. Currently the
imagebuilder is broken again:
openwrt-imagebuilder-21.02.0-rc3-ipq40xx-generic.Linux-x86_64$ make image PROFILE=avm_fritzbox-7530 PACKAGES=luci-ssl-openssl
...
Collected errors:
* pkg_hash_check_unresolved: cannot find dependency libiwinfo20210430 for luci-mod-status
* pkg_hash_fetch_best_installation_candidate: Packages for luci-mod-status found, but incompatible with the architectures configured
* pkg_hash_check_unresolved: cannot find dependency libiwinfo20210430 for rpcd-mod-iwinfo
* pkg_hash_fetch_best_installation_candidate: Packages for rpcd-mod-iwinfo found, but incompatible with the architectures configured
* satisfy_dependencies_for: Cannot satisfy the following dependencies for luci-ssl-openssl:
* libiwinfo20210430
* opkg_install_cmd: Cannot install package luci-ssl-openssl.
Everything because iwinfo's ABI was changed two times since rc3 release:
+IWINFO_ABI_VERSION:=20210430
+IWINFO_ABI_VERSION:=20210420
Since iwinfo is marked as nonshared, it wasn't built by phase2 builders, but
luci-mod-status was already updated 2 times since rc3 and was thus rebuilt by
phase2 builders:
d1d452ed2fb3 luci-mod-status: don't set '-' hostname when creating static lease
95b3633055c1 luci-mod-status: switch to html table for wlan channel analysis
So now luci-mod-status depends on libiwinfo20210430 but only
libiwinfo20210106 can be downloaded. This is first part of the fix, in
the upcoming commit Jo is going to remove nonshared flag from iwinfo
package as well.
References: https://lists.infradead.org/pipermail/openwrt-devel/2021-July/035736.html
References: https://lists.infradead.org/pipermail/openwrt-devel/2021-July/035741.html
Acked-by: Jo-Philipp Wich <jo@mein.io>
Reported-by: Nick Hainke <vincent@systemli.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
