This commit adds support for two variants of the already supported router
Acer Predator Connect W6: The Acer Predator Connect W6d (W6 without 6 GHz
wifi) and the Acer Connect Vero W6m (W6 without 2.5G eth1 port, usb3 port,
and the 6 on-board gpio RGB LEDs, and with a KTD2026 RGB LED controller
instead of the KTD2061 LED controller of the W6/W6d).
The device tree for the W6m refers to the KTD202x driver suggested in
PR #16860.
Patching target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
removes the code repetition in (old) lines 121 to 124 on the occasion.
This is the last of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2898d1d126)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In order to prepare OpenWrt support for other Acer W6 devices and to adapt
the procedure to read and set mac addresses which other devices of the same
target are using (instead of needing an additional script and creating an
additional structure in the file system), this commit
- reads device mac addresses from u-boot environment
- avoids the detour via the file system to set the mac addresses
- drops redundant file /lib/preinit/05_extract_factory_data.sh
The idea and the implementation were thankfully taken from PR #16410.
This is the second of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e7aaba2587)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All new routers are shipped with ubi size 112MB since early September.
Bootloader update required (ask vendor , see wiki)
These partitions weren't used:
firmware_backup
zrsave
config2
Signed-off-by: Romanov Danila <pervokur@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16686
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d8a9669093)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
The re-branded device comes with OpenWrt preinstalled, and an OpenWrt-based
U-Boot bootloader version. While the flash layout has been kept compatible
with the OpenWrt version found on the stock device (see [5]), the image format
changed, making a bootloader upgrade necessary.
Specifications:
SoC: Mediatek MT7981BA
RAM: 256MB
Flash: SPI-NOR 32 MiB (Winbond W25Q256)
WLAN: MT7976CN DBDC AX Wi-Fi
Switch: MT7531AE (4x LAN Gigabit ports, 1x WAN Gigabit port)
5G: Quectel RM520N modem
Watchdog: an external WDT connected to GPIO 6 is present and always running;
the built-in Mediatek watchdog is also present and effective, but
not used at the moment.
This porting has been tested only with 1x 5G modems installed (the device
supports up to two).
Installation:
Installation is possible via sysupgrade both in the stock device and
re-branded version. However, in the former case, updating the bootloader is
required.
OpenWrt-based U-Boot Bootloader installation
--------------------------------------------
The firmware flashed in the re-branded device at manifacturing time will
flash an OpenWrt-based U-Boot bootloader with some extra recovery features
(see [1]) at first boot.
To update the bootloader, you need to install the mtd-rw module and
insmod it:
insmod mtd-rw i_want_a_brick=1
Then update relevant flash partitions:
mtd erase u-boot-env
mtd erase BL2
mtd erase FIP
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-preloader.bin BL2
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-bl31-uboot.fip FIP
And reboot, making sure all previous commands ran succesfully.
If something goes wrong, you can recover your device via the mtk_uartboot
tool.
In my testing, it was possible to start the process even without (un)-plugging
the device, may be handy for remote recovery.
Installation from stock device and firmware
-------------------------------------------
To install vanilla OpenWrt in the stock device (R5000 5G Industrial router
from Yinghua Technologies) running the stock vendor firmware, you will need
to update your bootloader as described in previous section. Remember to use
-F (force upgrade) and -n (not keeping settings).
U-Boot Recovery
---------------
This procedure has been tested only with the OpenWrt-based U-boot bootloader.
Assign your system static IP address 192.168.1.1 and start a TFTP server. The
device will look for an initramfs image named
openwrt-mediatek-filogic-gatonetworks_gdsp-initramfs-kernel.bin
(so you may use openwrt/bin/targets/mediatek/filogic as root dir for your
TFTP server).
Power on the device while keeping the reset button pressed, until you see
a TFTP request from 192.168.1.10. Your environment will be restored to it's
default state.
MAC addresses assignment
------------------------
MAC addresses are assigned slightly differently than in stock firmware. In
particular, the 5 GHz Wi-Fi uses 2.4 GHZ MAC + 1, rather than reusing it with
LA bit set as done in stock firmware. This MAC address is allocated to the
device, so it can be used.
The 2.4 GHz Wi-Fi MAC address is the label MAC. LAN MAC is used to set the
special U-Boot environment ethaddr variable.
device MAC address U-Boot env variable factory partition offset
2.4 GHz Wi-Fi :84 wifi_mac 0x4
5.8 GHz Wi-Fi :85 not present not present
WAN :86 wan_mac 0x24
LAN :87 lan_mac 0x2A
Notes
-----
[1]: the OpenWrt-based U-Boot bootloader you will find installed in the
re-branded device is configured to request for the initramfs image via
TFTP for $gdsp_tftp_tries times before trying normal boot from NOR flash.
Setting this U-Boot environment variable to 0x0 will disable the feature,
which is not implemented in this patch.
[2]: the exposed UART port is connected to ttyS1; the ttyS0 console port is
not exposed.
[3]: the provided bootloader environment has no provision for operating on
BL2 and the FIP partitions. This is an intentional choice to make it
(slightly) more difficult to brick the device.
[4]: it seems GPIO 6 is used both for the "SYS" LED and external WDT.
[5] BL2 expects to find FIP payload at a fixed offset, so some constraints
apply.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
(cherry picked from commit b43194e041)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.
Signed-off-by: John Crispin <john@phrozen.org>
Read WiFi calibration data via NVMEM framework. The MAC addresses are
stored inside a file on a filesystem and hence still have to be
extracted in userspace.
WiFI EEPROM extraction has already accidentally been partially removed
by commit 3e6de5d77a ("mediatek: use NVMEM framework on all Adtran
devices").
Fixes: 3e6de5d77a ("mediatek: use NVMEM framework on all Adtran devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specification is similar to other devices of the MT Stuart series:
* Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 2500M/1000M/100M LAN port
* 10000M/5000M/2500M/1000M/100M/10M WAN port
* MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for the 2.5G port, 3x LED for the 10G port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix a typo in the MAC address assignment script affecting SDG-8734.
Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MediaTek SDK uses eth2 as additional LAN port and eth1 as WAN.
Do the same also in OpenWrt to keep settings aligned with the SDK.
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: MT40A512M16TB-062ER 1GB
Ethernet: 2x 2.5G, 4x 1G Lan
WiFi1: MT7976GN 2.4GHz 4T4R
WiFi2: MT7976AN 5.2GHz 4T4R
WiFi3: MT7915AN 5.8GHz 4T4R
Button: Reset, WPS, Turbo
USB: 1 x USB 3.0
Power: DC 12V 5A
Flash instructions:
1. Execute the following operation to open nc shell:
https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
2. Replace the stock bootloader to OpenWrt's:
dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
3. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
4. Download the initramfs image, and restart the router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
* Enter fakeroot if you are not login as root.
base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
ASR3000 via telnet.
Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Switch to new nvmem binding.
Also fixes a issue that the MAC address assigned to lan/wan was
reversed on eMMC boards.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Also use env variables exported by export_fitblk_rootdev() in
platform_copy_config().
Fixes: 4448d6325f ("mediatek: make use of common uImage.FIT upgrade functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add entry for the BananaPi R3 mini to the platform_check_image()
function where it has been missing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
WiFi calibration data is already obtained via in-kernel NVMEM framework.
There is no need to also do so in userspace.
Fixes: dd58ad968a ("mediatek/filogic: add OpenWrt One support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit adds support for TP-LINK RE6000XD.
The device is quite similar to the Mercusys MR90X V1,
except only 3 LAN ports and more LEDs.
So thanks to csharper2005 for doing all the groundwork.
Device specification
--------------------
SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM: MediaTek MT7986BLA (512MB)
Flash: SPI NAND GigaDevice (128 MB)
Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet: 1x2.5Gbe (LAN3 2.5Gbps), 2xGbE (LAN 1Gbps, LAN1,
LAN2)
WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs: 8 LEDs, 1 status blue, 2x WIFI blue, 2x signal
blue/red, 3 LAN blue gpio-controlled
Button: 2 (Reset, WPS)
USB ports: No
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, ubi0
partition contain "seconduboot" (also U-Boot 2022.01-rc4)
Serial console (UART), unpopulated
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
|
+--- Don't connect
Disassemble: rm the 2 screws at the bottom and the one at the backside.
un-clip the case starting at the edge above the LEDs.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot openwrt-mediatek-filogic-tplink_re6000xd-initramfs-kernel.bin bootm
4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Notice: while I was successfull at activating ssh (as described
here:
https://www.lisenet.com/2023/gaining-ssh-access-to-tp-link-re200-wi-fi-range-extender/)
Unfortunately I haven't found the correct root password.
Looks like they are using a static password
(md5crypt, salt + 21 characters) that is not the web
interface admin password.
The TP-LINK RE900XD looks like the very same device,
according to the pictures and the firmware.
But I haven't checked if the OpenWrt firmware works as well
on that device.
The second ubi partition (ubi1) is empty and there is no known
dual-partition mechanism, neither in u-boot nor in the stock firmware.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Switch to new nvmem binding.
Also fixes a issue that the MAC address assigned to lan/wan was reversed.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
- SOC: MediaTek MT7981
- ram: 256MB DDR3
- FLASH: 16MB SPI-NOR
- Ethernet: 2x1Gb Lan 1x1Gb Wan
- WIFI: MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4/5)
- LEDs: 2xLan 1x Wan 1x WIFI 1xSTATUS
MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
2G: 80:3F:5D:xx:xx:x3 partition "factory" at 0x4 (binary), on label
5G: 80:3F:5D:xx:xx:x3 Same as 2G
Installation Method 1: ssh
--------------------------
1. Connect PC to the lan port. Set the PC IP to 192.168.10.100 if
required.
2. Navigate to http://192.168.10.1/
3. Log into the Wavlink WebGUI. Default username/password is
admin/admin.
4. Use WebGUI to upgrade the firmware to
WAVLINK_WN586X3-A_M86X3A_V240113_WO-GDBYFM-modified.bin
downloaded from
https://github.com/themaverickdm/firmware-misc/tree/main/wavlink/wl-wn586x3
Warning: All settings will be lost!
5. Wait about 5 minutes, and after flashing is completed, log into
the router using (with admin123 as password):
ssh root@192.168.10.1
6. scp the openwrt image file onto the router, usually under /tmp
somewhere.
openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin
7. Flash openwrt image file like so:
mtd write \
openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin \
firmware
Warning: Previous firmware will be overwritten!
8. Wait about 5 minutes, and after the flashing is completed, set
the PC IP to 192.168.1.100 if required and log into the router
like so:
ssh root@192.168.1.1
Installation Method 2: u-boot
-----------------------------
1. Connect UART: TX-> 586X3 RX, RX-> 586X3 TX, GND-> 586 GND.
2. Connect PC to the wan (not lan!) port.
3. Setup the tftp server on PC, set IP to 192.168.10.100,
4. Power on the device. Select '2' to upgrade firmware in Uboot.
5. Input the image name and start to upgrade.
Uboot console log:
CPU: MediaTek MT7981
Model: mt7981-rfb
DRAM: 256 MiB
Core: 34 devices, 13 uclasses, devicetree: embed
Loading Environment from nowhere... OK
In: serial@11002000
Out: serial@11002000
Err: serial@11002000
Net:
Warning: ethernet@15100000 (eth0) using random MAC address -
02:47:fb:b2:53:2d
eth0: ethernet@15100000
UBOOT WN586X3A
gpio: pin 9 (gpio 9) value is 0
gpio: pin 10 (gpio 10) value is 0
gpio: pin 5 (gpio 5) value is 0
gpio: pin 12 (gpio 12) value is 0
gpio: pin 13 (gpio 13) value is 0
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade single image
6. Load image
0. U-Boot console
Co-authored-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: Sijia Huang <engineer31@win-star.com>
For the first-time installation (mostly migrates from vendor firmware)
the ubiblock is not ready, but bootdev detection relies on it. This
means users must create ubiblock manually otherwise the sysupgrade
will not work.
Now a unique case is added for nand devices which use new fit format,
let's move to it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS/Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Download the configration utilities:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
These binaries are extraced from the factory firmware, which are
dynamically linked with aarch64 musl 1.1.24. To use them, you
must run them under the same runtime environment, otherwise the
binaries will not work properly!
3. Upload the configuration and utilities to a suitable environment.
4. Uncompress the utilities, move them to '/bin' and give them executable permisison:
tar -zxf openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
mv mkconfig seama /bin
chmod +x /bin/mkconfig
chmod +x /bin/seama
5. Decrypt and uncompress the configuration:
Enter fakeroot if you are not login as root.
mkconfig -a de-enca -m EA0326GMP_3FE79221BAAA -i EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz -o backup.tar.gz
tar -zxf backup.tar.gz
6. Edit 'etc/config/dropbear', set 'enable' to '1'.
7. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
8. Repack the configuration:
tar -zcf backup.tar.gz etc/
mkconfig -a enca -m EA0326GMP_3FE79221BAAA -i backup.tar.gz -o EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz
9. Upload new configuration via web interface, now you can SSH to EA0326GMP.
A minimum configuration which enabled SSH access is also provided
to simplify the process:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-enable-ssh.tar.gz
Flash instructions:
1. SSH to EA0326GMP, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This pull request ports Ruijie RG-X60 Pro router support to the main branch.
Parameters:
- SoC : MediaTek MT7986A Quad-core ARM Cortex-A53 2.0GHz
- RAM : DDR3 512MiB (W634GU6QB)
- Flash : SPI-NAND 128 MiB (W25N01GVZEIG)
- WLAN : MediaTek MT7986A integration dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 4x4
- 5 GHz : a/n/ac/ax, MIMO 4x4
- Ethernet : 10/100/1000 Mbps x4 (MediaTek MT7531AE)
2500Mbps x 1 (Realtek RTL8221B-VB-CG)
- UART : through-hole on PCB
- [J500] GND, TX, RX, 3.3V (115200n1)
- Buttons : Mesh, Reset
- LEDs : 1x Power (Blue)
1x Turbo (Purple)
- Power : 12 VDC, 3 A
How to Installation:
1. Remove the case and connect the TTL cable to the corresponding position.
2. Power on the device and quickly press "down" on the keyboard, then
U-Boot will stay in the menu.
3. Select "1. Upgrade Firmware", select "0. TFTP Client(Default)".
4. Input the IP address, input the Openwrt image file name to be
flashed, start the TFTP server, and press "Enter".
5. Wait for the flashing to complete.
How return to stock:
1. Remove the case and connect the TTL cable to the corresponding
position.
2. Power on the device and quickly press "down" on the keyboard, then
U-Boot will stay in the menu.
3. Select "1. Upgrade Firmware", select "0. TFTP Client(Default)".
4. Input the IP address, input the Stock “E-WEBOS” image file name to
be flashed, start the TFTP server, and press "Enter".
5. Wait for the flashing to complete.
About recovery:
Connect uart, use u-boot menu to flash stock firmware image or boot
OpenWrt initramfs image.
About MAC Address:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 10:82:3D:XX:XX:9E | label |
| LAN | 10:82:3D:XX:XX:9F | label+1 |
| WLAN 2g | 10:82:3D:XX:XX:A0 | label+2 |
| WLAN 5g | 10:82:3D:XX:XX:A1 | label+3 |
+---------+-------------------+-----------+
Signed-off-by: Ashley Lee <code@emtips.net>
Add missing ';;' to the end of shell switch case statement.
Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Reported-by: @gl-dude
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The vendor U-Boot on the Cudy M3000 and the Yuncore AX835 assign random
mac addresses on boot and set the 'local-mac-address' property which
prevents Openwrt from assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add the
property, removes the workaround from 02_network, and adds back the nvmem
definition for the M3000.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Common specifications:
* Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 1x 10000M/1000M/100M + 3x 1000M/100M/10M LAN ports
* MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
* Airoha AG3352 GPS
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for each 1G port, 3x LED for each 10G port
* USB 3.0 type A port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
SDG-8733: 1x 10000M/1000M/100M WAN port
SDG-8734: 1x USXGMII/10GBase-R/5GBase-R/2500Base-X/1000Base-X/SGMII SFP+
Both models are also available in versions including 2x FXS POTS interfaces
for analog phones. Those interfaces are not supported by OpenWrt.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing call to emmc_copy_config which either writes the sysupgrade
tar.gz backup file or clears the existing rootfs_data overlay.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
filogic: Add support for D-Link AQUILA PRO AI M30
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 1GB RAM
- 16MB NOR
- 128MB NAND
- 3 LEDs (red, green, blue, white)
- 2 buttons (reset, user defined)
- 1 2.5Gbit WAN port (Airoha EN8811h)
- 1 1Gbit LAN ports
- 1 single lane M.2 SSD slot
- 1 mikroBus socket
- externel HW WDT (25s refresh time)
- i2c RTC (with battery backup)
Serial Interface
- UBS-C CDC-ACM
- 3 Pins GND, RX, TX
- Settings: 115200, 8N1
MAC addresses are not populated on the early samples.
Signed-off-by: John Crispin <john@phrozen.org>
Add ubi volumes for mt7988a-rfb and support for using factory data
for Ethernet MAC addresses and MT7996 WLAN calibration data.
Also add rootdisk handle. Removes the need to keep using nmbm
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware:
SoC: MT7981b
RAM: 256 MB
Flash: 128 MB SPI NAND
Ethernet:
1x 2.5Gbps (rtl8221b)
1x 1Gbps (integrated phy)
WiFi: 2x2 MT7981
Buttons: Reset, WPS
LED: 1x multicolor
Solder on UART:
- remove rubber ring on the bottom
- remove screws
- pull up the cylinder, maybe help by push on an ethernet socket with a screwdriver
- remove the (3) screws holding the board in the frame
- remove the board from the frame to get to the screws for the silver, flat heat shield
- remove the (3) screws holding the heat shield
- solder UART pins to the back of the board
- make sure to have the pins point out on side with the black, finned heat spread
- the markings for the pins are going to be below the silver heat shield
- Vcc is not needed
If you don't intend on using the UART outside of the installation process, you might not
want to solder:
- carefully scrape off the thin layer of epoxy on the holes (not the copper)
- place your pin header with the UART attached in the holes
- the pins, starting with the one closest to the socket:
- Vcc (not required)
- GND
- RX
- TX
- either wedge the header or hold it with your fingers so that the pins stay in contact with the board
Installation (UART):
- attach an Ethernet cable to the 1Gbps port (black) on the router
- hold the reset button while powering the router
- press CTRL-C or wait for the timeout to get to the U-Boot prompt
- prepare a TFTP server on the network to supply ..-initramfs-kernel.bin
- use 'tftpboot' in the U-Boot shell to pull the image
- boot the image using 'bootm'
- push the ..-sysupgrade to the router using your preferred method
- perform the upgrade with 'sysupgrade -n'
There is a recovery mechanism that involves fetching a file called 'recovery.bin' but that is not understood yet.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: internal test points, 115200 8n1
- Power: 5 VDC, 3 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 82:af:ca:xx:xx:x0 | |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware to make installation easier, and so I recommend checking the Wiki for this device if there is a more convenient solution than the one below.
To install using TFTP:
1. Connect to UART.
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an OpenWrt initramfs-kernel.bin firmware file.
5. Run these steps in u-boot using the name of your file.
setenv bootfile initramfs-kernel.bin
tftpboot
bootm
6. If you can reach LuCI or SSH now, just use the sysupgrade image with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
This adds support for the bpi-r4 variant with internal 2.5G PHY and
additional ethernet port instead of second sfp.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
