In most cases check-size is used with IMAGE_SIZE and vice versa. Let check-size
use IMAGE_SIZE by default.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.
For ramips, remove redundant values already present in parent file.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Ubiquiti Bullet M (AR7240).
Specifications:
- AR7240 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- External antenna
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Attention: airOS firmware versions >= 5.6 have a new bootloader with
an incompatible partition table!
Please downgrade to <= 5.5 _before_ flashing OpenWrt!
Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other Ubiquiti M boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_bullet-m-ar7240-squashfs-factory.bin
The "fixed-link" section of the device tree is needed to avoid errors like this:
Generic PHY mdio.0:1f:04: Master/Slave resolution failed, maybe conflicting manual settings?
With "fixed-link", the errors go away and eth0 comes up reliably.
Signed-off-by: Russell Senior <russell@personaltelco.net>
[fix SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The v5.4 kernel already works much better than v4.19
as so many things got upstreamed so let's just bump
it to kernel v5.4.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a kernel config file for the v5.4 gemini
kernel.
No major changes compared to v4.19, mainly
CONFIG_MTD_PHYSMAP_OF_GEMINI was renamed to
CONFIG_MTD_PHYSMAP_GEMINI.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[select UNWINDER_ARM, set CONFIG_DRM_FBDEV_OVERALLOC, drop
dropped 4.19 symbols, kernel config refreshed]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds the kernel patches needed for the Gemini.
Just 7 patches, 5 of them are already upstream.
Notably we incorperate the temperature sensor on the
hard drive to drive temperature control of the NAS
chassis. This is required for the DIR-685 which has
no external temperature sensor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[use the drivetemp package over the backport]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
These have been discovered by the gemini 5.4 patches.
This is because one of the devices uses the FBDEV emulation.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch backports the hwmon drivetemp sensor module from vanilla
linux 5.5 to be available on OpenWrt's 5.4 kernel.
Extract from The upstream commit by Guenter Roeck <linux@roeck-us.net>:
hwmon: Driver for disk and solid state drives with temperature sensors
"Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.
This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.
With this driver, the hard disk temperature can be read [...]
using sysfs:
$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000
If the drive supports SCT transport and reports temperature limits,
those are reported as well.
drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1: +27.0<C2><B0>C (low = +0.0<C2><B0>C, high = +60.0<C2><B0>C)
(crit low = -41.0<C2><B0>C, crit = +85.0<C2><B0>C)
(lowest = +23.0<C2><B0>C, highest = +34.0<C2><B0>C)
The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism."
This patch incorperates a patch made by Linus Walleij:
820-libata-Assign-OF-node-to-the-SCSI-device.patch
This patch is necessary in order to wire-up the drivetemp
sensor into the device tree's thermal-zones.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This version includes bug and security fixes, including medium-severity
CVE-2019-1551, affecting RSA1024, RSA1536, DSA1024 & DH512 on x86_64.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This adds commented configuration help for the alternate, afalg-sync
engine to /etc/ssl/openssl.cnf.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Sungbo Eo <mans0n@gorani.run> submitted another patch fixing an error
on reboot:
irqchip/versatile-fpga: Apply clear-mask earlier
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
qemustart allows easy testing of created images via `qemu`. The script
automatically selects created images and can setup e.g. networks.
As the x86 target now uses the generic image.mk the profile appears also
in the image name, this is *generic*.
Add the profile name to the qemustart script so it still finds the file.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The previous image generation code would always gzipped images.
This patch changes the behaviour and only compresses images when
selected in menuconfig.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Rely on device profiles instead for packages selection.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebase, adjusted commit title]
Signed-off-by: Paul Spooren <mail@aparcar.org>
This commit introduces few related changes which need to be done in
single commit to keep images buildable between git revisions. In result
it retains all previous image creation possibilities with slight name
change of generated images. Brief summary of the commit:
* Split up image generation recipe to smaller chunks to make it more
generic and reusable.
* Make iso images x86 specific and drop their definition as root
filesystem.
* Convert image creation process to generic code specified in image.mk.
* Make geode subtarget inherit features from the main target instead of
redefining them.
* For subtargets create device definitions with basic packages set.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebased]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Let the grub2 package take care of creating installable grub2 images,
this will allow creating grub2 images without first calling x86 image
generation recipe. Also as side effect, since those images are now
shared, it'll reduce the number of calling grub-mkimage.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebase, adjusted commit title]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Fix header change that was done for kernel but 4.19 got missed for 5.4.
Solves nasty errors like:
8.4.0_musl/include/linux/netfilter/xt_CONNMARK.h:5,
from connmark_listener.c:30:
/builder/shared-workdir/build/sdk/staging_dir/toolchain-aarch64_cortex-a53_gcc-8.4.0_musl/include/linux/netfilter/xt_connmark.h:23:2: error: enumerator value for 'XT_CONNMARK_VALUE' is not an integer constant
XT_CONNMARK_VALUE = BIT(0),
^~~~~~~~~~~~~~~~~
/builder/shared-workdir/build/sdk/staging_dir/toolchain-aarch64_cortex-a53_gcc-8.4.0_musl/include/linux/netfilter/xt_connmark.h:25:1: error: enumerator value for 'XT_CONNMARK_DSCP' is not an integer constant
};
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
WireGuard had a brief professional security audit. The auditors didn't find
any vulnerabilities, but they did suggest one defense-in-depth suggestion to
protect against potential API misuse down the road, mentioned below. This
compat snapshot corresponds with the patches I just pushed to Dave for
5.6-rc7.
* curve25519-x86_64: avoid use of r12
This buys us 100 extra cycles, which isn't much, but it winds up being even
faster on PaX kernels, which use r12 as a RAP register.
* wireguard: queueing: account for skb->protocol==0
This is the defense-in-depth change. We deal with skb->protocol==0 just fine,
but the advice to deal explicitly with it seems like a good idea.
* receive: remove dead code from default packet type case
A default case of a particular switch statement should never be hit, so
instead of printing a pretty debug message there, we full-on WARN(), so that
we get bug reports.
* noise: error out precomputed DH during handshake rather than config
All peer keys will now be addable, even if they're low order. However, no
handshake messages will be produced successfully. This is a more consistent
behavior with other low order keys, where the handshake just won't complete if
they're being used anywhere.
* send: use normaler alignment formula from upstream
We're trying to keep a minimal delta with upstream for the compat backport.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* netlink: initialize mostly unused field
* curve25519: squelch warnings on clang
Code quality improvements.
* man: fix grammar in wg(8) and wg-quick(8)
* man: backlink wg-quick(8) in wg(8)
* man: add a warning to the SaveConfig description
Man page improvements. We hope to rewrite our man pages in mdocml at some
point soon.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
mt76 is a target default package for mt7622-wmac only.
mt7623 doesn't have integrated wireless support and wifi drivers for
pcie cards should be added as device specific package.
mt7629-wmac isn't supported by mt76 yet.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
rename "kernel" partition in upstream dts to "firmware" and add
denx,fit as compatible string for mtdsplit.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
1. fix typo: ucidef_set_interfaces_wan -> ucidef_set_interface_wan
2. change board name to mt7629-rfb to match upstream dts
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This external switch driver should be loaded on boot for network support
in failsafe mode.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[alter commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit adds definition of DEBUG0 and DEBUG1 registers and replace
magic values with proper register modifying.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
For virtual access points (when multiple SSIDs are used for one
physical AP), there exist one physical network interface and
multiple virtual interfaces, which are fully under control of
hostapd. When networking is setup, the script
`/lib/netifd/wireless/mac80211.sh` is called, which tries to bring
the interface up by a call to `ip link set dev <iface> up`. This
call might fail for virtual APs, because the virtual interface
might not have been created by hostapd yet. There are some artifical
delays in the script most probably to handle this, but when DFS
channel availability check on 5GHz band is issued, hostapd can
delay creating virtual interfaces by a minute.
In order to fix this (or work around it), do not try to bring the
interface up (this is responsibility of hostapd anyway) and
do not try to set txpower on the virtual interface.
Fixes FS#2698.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
1. KERNEL_CRASH_DUMP should depends on KERNEL_PROC_KCORE (kexec use it)
2. select crashkernel mem size by totalmem
mem <= 256M disable crashkernel by default
mem >= 4G use 256M for crashkernel
mem >= 8G use 512M for crashkernel
default use 128M
3. set BOOT_IMAGE in kdump.init
4. resolve a "Unhandled rela relocation: R_X86_64_PLT32" error
Tested on x86_64
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Sungbo Eo <mans0n@gorani.run> posted a patch fixing the long-standing
reboot problem on the OXNAS OX820 platform:
irqchip/versatile-fpga: Handle chained IRQs properly
It got queued for 5.7. Import it to oxnas target patches for now.
Fixes: b4917fa907 ("oxnas: fix oxnas-rps-timer dt-match")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When introducing ubus reload support, ubus initialization was moved
to the service level instead of being carried out when adding a BSS
configuration. While this works when using wpa_supplicant in that way,
it breaks the ability to run wpa_supplicant on the command line, eg.
for debugging purposes.
Fix that by re-introducing ubus context intialization when adding
configuration.
Reported-by: @PolynomialDivision https://github.com/openwrt/openwrt/pull/2417
Fixes: 60fb4c92b6 ("hostapd: add ubus reload")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
TP-Link Archer D7 v1 is a dual-band AC1750 router + modem.
The router section is based on Qualcomm/Atheros QCA9558 + QCA9880.
The "DSL" section is based on BCM6318 but it's currently not supported.
The Archer D7b seems to differ from the Archer D7 only in the
partition table.
Router section - Specification:
775/650/258 MHz (CPU/DDR/AHB)
128 MB of RAM (DDR2)
16 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
4x 10/100/1000 Mbps Ethernet
7x LED, 2x button
UART header on PCB
Known issues:
- Broadband LED (missing GPIO - probably driven by the BCM6318)
- Internet LED (missing GPIO - probably driven by the BCM6318)
- WIFI LED (working only for one interface at a time, while in the
OEM firmware works for both wifi interfaces; thus, this patch does
not set a trigger by default)
- DSL not working (eth0)
UART connection
---------------
J1 HEADER (Qualcomm CPU)
. VCC
. GND
. RX
O TX
J41 HEADER (Broadcom CPU)
. VCC
. GND
. RX
O TX
The following instructions require a connection to the J1 UART header
and are tested for the Archer D7 v1.
For the Archer D7b v1, names should be changed accordingly.
Flash instructions under U-Boot, using UART
------------------------------------------
1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-squashfs-sysupgrade.bin
erase 0x9f020000 +f90000
cp.b 0x81000000 0x9f020000 0xf90000
reset
Initramfs instructions under U-Boot for testing, using UART
----------------------------------------------------------
1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-initramfs-kernel.bin
bootm 0x81000000
4. Here you can backup the original firmware and/or flash the sysupgrade openwrt if you want
Restore the original firmware
-----------------------------
0. Backup every partition using the OpenWrt web interface
1. Download the OEM firmware from the TP-Link website
2. Extract the bin file in a folder (eg. Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin)
3. Remove the U-Boot and the Broadcom image part from the file.
Issue the following command:
dd if="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin" of="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod" skip=257 bs=512 count=31872
4. Double check the .mod file size. It must be 16318464 bytes.
5. Flash it using the OpenWrt web interface. Force the update if needed.
WARNING: Remember to NOT keep settings.
5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
Issue below commands in the U-Boot:
tftpboot 0x81000000 Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod
erase 0x9f020000 +f90000
cp.b 0x81000000 0x9f020000 0xf90000
reset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[cosmetic DTS changes, remove TPLINK_HWREVADD := 0, do not use two
phyXtpt at once, add missing buttons, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer C60 v3 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.
It seems to be identical to the v2 revision, except that
it lacks a WPS LED and has different GPIO for amber WAN LED.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 2x button
- UART header on PCB
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
While TFTP works for OpenWrt images, my device didn't accept the
only available official firmware "Archer C60(EU)_V3.0_190115.bin".
In contrast to earlier revisions (v2), the v3 contains the (same)
MAC address twice, once in 0x1fa08 and again in 0x1fb08.
While the partition-table on the device refers to the latter, the
firmware image contains a different partition-table for that region:
name device firmware
factory-boot 0x00000-0x1fb00 0x00000-0x1fa00
default-mac 0x1fb00-0x1fd00 0x1fa00-0x1fc00
pin 0x1fd00-0x1fe00 0x1fc00-0x1fd00
product-info 0x1fe00-0x1ff00 0x1fd00-0x1ff00
device-id 0x1ff00-0x20000 0x1ff00-0x20000
While the MAC address is present twice, other data like the PIN isn't,
so with the partitioning from the firmware image the PIN on the device
would actually be outside of its partition.
Consequently, the patch uses the MAC location from the device (which
is the same as for the v2).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since there exists another variant of the Bullet M with AR7240 SoC
under the same name, this patch introduces the SoC into the device
name to be able to distinguish these variants.
Signed-off-by: Russell Senior <russell@personaltelco.net>
[add commit message, adjust model in DTS, fix 02_network and
SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Prepare to support the AR7240 variant of ubiquiti bullet m, by
reorganizing the related dtsi files.
* Distribute SOC variable across ubnt-xm devices.
Signed-off-by: Russell Senior <russell@personaltelco.net>
The PoE hat supported on the RPi 3B+ and 4B comes with a rather
loud fan, tripped in two steps by the brcmstb_thermal
thermal_zone driver. Enabling writable trip points allow
users to adjust the fan trip points according to their
preferred temp/noise ratio.
This setting is enabled on most other targets with similar
thermal_zone controlled cooling devices.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
We do not build images with a jffs2 rootfs, but jffs2 is still used as
filesystem for the rootfs_data.
Fixes: e3eaf57808 ("lantiq: kernel 5.4: debloat kernel config")
Signed-off-by: Mathias Kresin <dev@kresin.me>
When creating the mikrotik subtarget, the execute bit on 02_network
was not set. Fix it.
Fixes: a66eee6336 ("ath79: add mikrotik subtarget")
Reported-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, specifying "BOARD_NAME := routerboard" is required by the
upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard"
is hardcoded in platform_do_upgrade_mikrotik_nand().
This patch replaces the latter with a grep for the name like it
is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh.
By that, BOARD_NAME is obsolete now for this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, specifying "BOARD_NAME := routerboard" is required by the
upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard"
is hardcoded in platform_do_upgrade_mikrotik_rb().
This patch replaces the latter with a grep for the name like it
is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh.
This should enable upgrades from ar71xx to ath79 without setting
BOARD_NAME for the latter.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit creates the ath79/mikrotik subtarget in order to support
MikroTik devices based on Qualcomm Atheros MIPS SoCs.
MikroTik devices need a couple of specific features: the split MiNOR
firmware MTD format, which is not used by other devices, and the 4k
sector erase size on SPI NOR storage, which can not be added to the
ath79/generic and ath79/nand subtargets now.
Additionally, the commit moves the two MikroTik devices already in
the generic and nand subtargets to this new one.
Tested on the RB922 board and the wAP AC router.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Pogoplug V3/Pro has an interanl SATA port. To use it, DTS sata node should be
enabled, and kmod-ata-oxnas-sata package needs to be installed.
Fixes: FS#2542
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
