This commit adds support for the Linksys EA6350v3 device in the ipq-wifi
target.
Without this patch, the Linksys EA6350v3 won't be hable to have fully
functional wireless interfaces. This is not permanent: the board data has
already been sent to ath10k _at_ lists _dot_ infradead _dot_ org
Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
This patch adds several country codes to the regd.h and regd_common.h
files in order to support devices whose country codes are not present in
the original list.
Without this patch, all devices whose manufacturer programmed any of these
code in their EEPROM will run without wireless interfaces.
Signed-off-by: Oever González <notengobattery@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [matched signed-off]
CPU: FSL P1020 (2x 800MHz E500 PPC)
RAM: 1GB DDR3
FLASH: 256MiB NAND
WiFi: 2x Atheros AR9382 2x2:2 abgn
ETH: 2x BCM54616S - 1x BCM53128 8-port switch
LED: 5x LEDs (Power, WiFi1, WiFi2, N/D, SYS)
BTN: 1x RESET
Installation
------------
1. Download initrams kernel image, dtb binary and sysupgrade image.
2. Place initramfs kernel into tftp root directory. Rename to
"panda-uimage-factory".
3. Place dtb binary into tftp root directory. Rename to "panda.fdt".
4. Start tftp server on 192.168.100.8/24.
5. Power up the device with the reset button pressed. It will download
the initrams and dtb via tftp and boot into OpenWRT in RAM.
6. SSH into the device and remove the factory partitions.
> ubirmvol /dev/ubi0 --name=kernel1
> ubirmvol /dev/ubi0 --name=rootfs1
> ubirmvol /dev/ubi0 --name=devicetree1
You will have around 60 MiB of free space with that.
You can also delete "kernel2", "devicetree2", "rootfs2" and "storage"
respectively in case you do not want to go back to the vendor firmware.
7. Modify the U-Boot bootcmd to allow for booting OpenWRT
> fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel
&& bootm 0x1000000"
> fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200
ubi.mtd=3,2048"
> fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt"
8. Transfer the sysupgrade image via scp into the /tmp directory.
9. Upgrade the device
> sysupgrade -n /tmp/<imagename>
Signed-off-by: David Bauer <mail@david-bauer.net>
The library has an usual shared object file name, which caused the
install glob pattern to miss the actual so.
Fixes: #2082
Fixes; 0e70f69a35 ("treewide: revise library packaging")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This bumps ppp to latest git version.
There is one upstream commit, which changes DES encryption calls from
libcrypt / glibc to openssl.
As long as we don't use glibc-2.28, revert this commit.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Initially this patch was introduced as a quick fix following
the removal of 936-ath10k_skip_otp_check.patch which caused
multiple ath10k pcie devices in various ipq806x and ar71xx/ath79
targets to malfunction.
Thankfully, the affected devices have been updated to utilize
the pre-caldata method. And finally with the switch to ath10k-ct,
which never had the patch or any reports of similar issues, I
think it's time to remove this patch since it is no longer needed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The ABI_VERSION:=1 tag will take care of transforming the binary
library package basename.
Add a virtual PROVIDES:=libelf1 for packages still having libelf1
in their DEPENDS:=... lists.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Last incompatible change appeared to be 4924411
("http: add proper error handling to uclient_http_redirect()") which
changed the return value of uclient_http_redirect() from bool to int.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* tools: curve25519: handle unaligned loads/stores safely
This should fix sporadic crashes with `wg pubkey` on certain architectures.
* netlink: auth socket changes against namespace of socket
In WireGuard, the underlying UDP socket lives in the namespace where the
interface was created and doesn't move if the interface is moved. This
allows one to create the interface in some privileged place that has
Internet access, and then move it into a container namespace that only
has the WireGuard interface for egress. Consider the following
situation:
1. Interface created in namespace A. Socket therefore lives in namespace A.
2. Interface moved to namespace B. Socket remains in namespace A.
3. Namespace B now has access to the interface and changes the listen
port and/or fwmark of socket. Change is reflected in namespace A.
This behavior is arguably _fine_ and perhaps even expected or
acceptable. But there's also an argument to be made that B should have
A's cred to do so. So, this patch adds a simple ns_capable check.
* ratelimiter: build tests with !IPV6
Should reenable building in debug mode for systems without IPv6.
* noise: replace getnstimeofday64 with ktime_get_real_ts64
* ratelimiter: totalram_pages is now a function
* qemu: enable FP on MIPS
Linux 5.0 support.
* keygen-html: bring back pure javascript implementation
Benoît Viguier has proofs that values will stay well within 2^53. We
also have an improved carry function that's much simpler. Probably more
constant time than emscripten's 64-bit integers.
* contrib: introduce simple highlighter library
This is the highlighter library being used in:
- https://twitter.com/EdgeSecurity/status/1085294681003454465
- https://twitter.com/EdgeSecurity/status/1081953278248796165
It's included here as a contrib example, so that others can paste it into
their own GUI clients for having the same strictly validating highlighting.
* netlink: use __kernel_timespec for handshake time
This readies us for Y2038. See https://lwn.net/Articles/776435/ for more info.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Update to the latest version of iproute2; see https://lwn.net/Articles/776174/
for a full overview of the changes in 4.20.
Remove upstream patch 001-fix-print_0xhex-on-32-bit.patch and 002-tc-fix-xtables-incorrect-usage-of-LDFLAGS.patch
Introduce a patch to include <linux/limits.h> for XATTR_SIZE_MAX in tc
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
On musl based distributions, u-boot 2010.03 fails to build with:
u-boot-2010.03/include/u-boot/crc.h:29:50: error: unknown type name 'uint'
uint32_t crc32 (uint32_t, const unsigned char *, uint);
The issue was fixed in the newer u-boot-2018.03 version, this commit
backports the change to the older version used by ar71xx/ath79.
Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
[add commit message from PR description]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The crypt(3) function is allowed to fail with either EINVAL or ENOSYS when
the given salt is either invalid or when the requested algorithm is not
implemented.
In such a case, libbb's pw_encrypt() function will silently convert the
crypt() NULL return value into an empty string which is then processed
without further errors by utilities such as chpasswd or passwd, causing
them to set an empty password when an unsupported cipher is requested.
Patch the relevant users of pw_encrypt() to abort in case an empty hash
is returned by pw_encrypt() in order to mitigate the problem.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Since readline/host links ncurses/host now, we need to ensure that the
libncursesw.so host library is built with -fPIC.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This may be useful if you don't entirely trust your flash and want to be able
to check for corruptions.
Signed-off-by: Michal Hrusecky <Michal@Hrusecky.net>
This adds a wrapper (uci_load_validate) for uci_validate_section() that
allows callers (through a callback function) to access the values set by
uci_validate_section(), without having to manually declare a
(potentially long) list of local variables.
The callback function receives two arguments when called, the config
section name and the return value of uci_validate_section().
If no callback function is given, then the wrapper exits with the value
returned by uci_validate_section().
This also updates several init scripts to use the new wrapper function.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
these utilities need to run with uid 0 to be useful. Thus,
install them setuid root like other distros do, too.
Signed-off-by: Carsten Wolff <carsten@wolffcarsten.de>
[use INSTALL_SUID macro]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Linux kernel has a polling mechanism that can be activated by changing
the parameter /sys/module/block/parameters/events_dfl_poll_msecs which
is deactivated by default or the /sys/block/[device]/events_poll_msecs
for one device.
This patch set the events_poll_msecs when a disk is inserted.
Once the media disk change event is sent by the kernel then we force a
re-read of the devices using /sbin/block info.
With this patch, insertion and ejection of sd card will automatically
generate partition devices in /dev.
Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[rewrap commit message, fix bashisms, fix non-matching condition,
bump pkg release]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Also fix the libxxxw.so* -> libxxx.so* linking to actually work, the
prevsious code failed to properly symlink the versioned .so files.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update (lib)readline to 8.0
Remove autoreconf
Remove blankspace at the end of the lines in description
Remove --enable-shared and --enable-static as they're enabled by default
Remove TARGET_CPPFLAGS
Simplify install sections
Install readline.pc (pkgconfig)
Add patch for linking (lib)ncurses
Source:
https://git.buildroot.net/buildroot/plain/package/readline/0000-curses-link.patch
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
In order to prepare the switch from librpc to libtirpc, we need to relocate
conntrack-tools to the packages feed.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
d273ddd mt7603: fix number of frames limit in .release_buffered_frames
63bf183 mt76: add channel switch announcement support
e45db12 mt7603: fix tx status info
9d11596 mt7603: discard bogus tx status data
4bcb2f9 mt7603: fix txd q_idx field value
4206db7 mt76: set IEEE80211_HW_NEEDS_UNIQUE_STA_ADDR flag
c4e4982 mt7603: set IEEE80211_HW_TX_STATUS_NO_AMPDU_LEN
702f557 mt7603: use maximum tx count for buffered multicast packets
158529d mt7603: fix PSE reset retry sequence
fc31457 mt7603: implement support for SMPS
Signed-off-by: Felix Fietkau <nbd@nbd.name>
e7e8ee5f Update bash_completion
b3b4e335 Update manual pages
bd93d90a Don't treat text as option if it matches -[0-9]
ea69c84b Bump up version number to 1.36.0
783b649b Update AUTHORS
eb21e6f8 Merge branch 'update-http-parser'
ab2aa567 Fix test failure
ff87a542 Use http-parser 0d0a24e19eb5ba232d2ea8859aba2a7cc6c42bc4
439dbce6 Merge branch 'nghttpx-h1-connection-pool-per-addr'
e9c9838c nghttpx: Pool h1 backend connection per address
803d4ba9 Merge branch 'nghttpx-randomize-roundrobin-order'
732245e5 make clang-format
9e8d5433 Use clang-format-7
fdcdb21c nghttpx: Randomize backend address round robin order per thread
11d0533c nghttpx: Ensure that cert serial does not exceed 20 bytes
dbb5f00d Merge pull request #1287 from rckclmbr/fix_serial_size
9cc412e2 Merge pull request #1285 from staticinvocation/master
5b2efc0a Fix getting long serial numbers for openssl < 1.1
7e4c48a4 Disable shared library if ENABLE_SHARED_LIB is OFF
082e162f Merge pull request #1282 from alagoutte/travis
7cc7c06c .travis(.yml): no longer need llvm-toolchain-trusty-7
12ebeb30 .travis(.yml): Update to Xenial
c78abbe1 Update mruby to 2.0.0
124c7848 nghttpx: Add missing return
ce9667c4 Merge branch 'nghttpx-fix-trailing-slash-handling'
f3f40840 nghttpx: Fix broken trailing slash handling
302abf1b h2load: Fix compile error with gcc
089a03be h2load: Write log file with write(2)
de4fe728 Merge branch 'pyos-master'
d1b3a83f h2load: add an option to write per-request logs
eb679253 Merge branch 'puscas-port_in_use'
6800d317 added access to the number of the current server port
c98362ea Bump up version number to 1.36.0-DEV
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Add the ABI_VERSION source makefile variable to the binary package basename
and resolve source dependencies on packages with ABI_VERSION set to such
expanded names.
If for example a package specifies DEPENDS:=libopenssl while the OpenSSL
Makefile specifies ABI_VERSION:=1.0.0, the resulting ipk control data
dependency will be "Depends: libopenssl1.0.0" and the libopenssl ipk file
will be called "libopenssl1.0.0_<version>_<arch>.ipk".
The next time a library such as OpenSSL is updated to an incompatible
version, the ABI_VERSION shall be changed accordingly to prevent opkg from
simply upgrading to an incompatible library without considering the
dependencies of already installed packages.
Also introduce another "SourceName" control field which is required by
the newly introduced "scritps/ipkg-remove" to determine the proper related
.ipk files to delete upon buildroot package clean operations.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In the case of upstream libraries, set the ABI_VERSION variable to the
soname value of the first version version after the last backwards
incompatible change.
For custom OpenWrt libraries, set the ABI_VERSION to the date of the
last Git commit doing backwards incompatible changes to the source,
such as changing function singatures or dropping exported symbols.
The soname values have been determined by either checking
https://abi-laboratory.pro/index.php?view=tracker or - in the case
of OpenWrt libraries - by carefully reviewing the changes made to
header files thorough the corresponding Git history.
In the future, the ABI_VERSION values must be bumped whenever the
library is updated to an incpompatible version but not with every
package update, in order to reduce the dependency churn in the
binary package repository.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This update fixes some cosmetical issues and a number of segmentation
faults when parsing lists having Conflicts or Replaces tags.
d217daf libopkg: fix replacelist parsing and writing
9dd9a07 libopkg: fix segmentation fault when traversing conflicts
34571ba libopkg: consider provided packages in pkg_vec_mark_if_matches()
18740e6 opkg_download: print error when fork() fails
e3d7330 libopkg: don't print unresolved dependencies twice
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
f52bb5b fix previous commit
18eac67 Fix entries in /etc/hosts disabling static leases.
f8c77ed Fix removal of DHCP_CLIENT_MAC options from DHCPv6 relay replies.
4bf62f6 Tidy cache_blockdata_free()
9c0d445 Fix e7bfd556c079c8b5e7425aed44abc35925b24043 to actually work.
2896e24 Check for not(DS or DNSKEY) in is_outdated_cname_pointer()
a90f09d Fix crash freeing negative SRV cache entries.
5b99eae Cache SRV records.
2daca52 Fix typo in ra-param man page section.
2c59473 File logic bug in cache-marshalling code. Introduced a couple of commits back.
cc921df Remove nested struct/union in cache records and all_addr.
ab194ed Futher address union tidying.
65a01b7 Tidy address-union handling: move class into explicit argument.
bde4647 Tidy all_addr union, merge log and rcode fields.
e7bfd55 Alter DHCP address selection after DECLINE in consec-addr mode. Avoid offering the same address after a recieving a DECLINE message to stop an infinite protocol loop. This has long been done in default address allocation mode: this adds similar behaviour when allocaing addresses consecutively.
The most relevant fix for openwrt is 18eac67 (& my own local f52bb5b
which fixes a missing bracket silly) To quote the patch:
It is possible for a config entry to have one address family specified by a
dhcp-host directive and the other added from /etc/hosts. This is especially
common on OpenWrt because it uses odhcpd for DHCPv6 and IPv6 leases are
imported into dnsmasq via a hosts file.
To handle this case there need to be separate *_HOSTS flags for IPv4 and IPv6.
Otherwise when the hosts file is reloaded it will clear the CONFIG_ADDR(6) flag
which was set by the dhcp-host directive.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
7abbed4 dhcpv6: add setting to choose IA_NA, IA_PD or both
dd1aefd router: add syslog tracing for skipped routes
0314d58 router: filter route information option
5e99738 router: make announcing DNS info configurable (FS#2020)
1fe77f3 router: check return code of odhcpd_get_interface_dns_addr()
8f49804 config: check for invalid DNS addresses
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
331ac70 Correctly update parent qlen when splitting GSO packets
581967c Makefile: Hook into Kbuild/Kconfig infrastructure
The parent qlen change is relevant if using cake as a leaf qdisc,
the makefile is a no-op.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
4ea9a2db164c Update upload-release.sh script and po files.
a01938d584b9 libelf: Mark both fsize and msize with const attribute.
c338a0541663 libebl: Don't update w, t and len unnecessarily in ebl_object_note_type_name.
422b549007f6 Prepare for 0.175
22ec8efc1dd8 elflint: Allow PT_GNU_EH_FRAME segment to match SHT_X86_64_UNWIND section.
cf10453f8252 libelf: Correctly setup alignment of SHF_COMPRESSED section data.
d3e6266754b9 strip: Also handle gnu compressed debug sections with --reloc-debug-sections
72e30c2e0cb4 Handle GNU Build Attribute ELF Notes.
7a3f6fe60b85 Recognize NT_VERSION notes.
cff53f1784c9 libcpu: Recognize bpf jump variants BPF_JLT, BPF_JLE, BPF_JSLT and BPF_JSLE
ecbe3120cddb libdwelf: New function dwelf_elf_begin.
4b0342b85b5b backends: Add x86_64 section_type_name for SHT_X86_64_UNWIND.
825e48c4e942 Also find CFI in sections of type SHT_X86_64_UNWIND
4789e0fb92b0 libelf: Explicitly update section data after (de)compression.
1628254ba215 strip: Add --reloc-debug-sections-only option.
f2d59180b90b strip: Extract code to update shdrstrndx into new common function.
f6ae0ab9350e strip: Split out debug section relocation into separate helper functions.
b15ee95bcee4 strip: Always copy over any phdrs if there are any.
e574889d92b1 unstrip: Add ELF_CHECK to make sure gelf_getehdr () doesn't return NULL.
5199e15870e0 Recognize and parse GNU Property notes.
b75ff1bbd060 addr2line: Use elf_getshdrstrndx not Ehdr field to print section name.
35197ea4c43e readelf: Use shstrndx to lookup section names.
9a74c190a2b3 backends: ppc use define instead of const for size of dwarf_regs array.
72d023b35f36 readelf: Make sure readp is smaller than cieend in print_debug_frame_section.
dce0b3b63ba0 readelf: Make sure readp is smaller than cieend in print_debug_frame_section.
1e7c230b277b Check sh_entsize is not zero.
22d2d082d57a size: Handle recursive ELF ar files.
2b16a9be6993 arlib: Check that sh_entsize isn't zero.
4cdb0fd0d3b4 ar: Assume epoch if ar_date is bogus.
577511f66842 findtextrel: Check that sh_entsize isn't zero.
20f9de9b5f70 libdwfl: Sanity check partial core file data reads.
2f4a040fab52 readelf: Handle multiple .debug_macro sections and decode header flag.
eee4269e5315 unstrip: Renumber the group section indexes.
c06ab0bbb476 strip, unstrip: Handle SHT_GROUP correctly.
2876b3b648f6 Handle ADD/SUB relocations
69d6e67eee30 tests: backtrace-dwarf.c improve error handling in test framework.
Originally-produced--by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Commit 3f0eb71dae added ALTERNATIVES for wget but not in correct
alphabetical order; increase PKG_RELEASE as well.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Don't symlink uclient-fetch anymore to /bin/wget but rather use
the ALTERNATIVES support for wget to install it as /usr/bin/wget.
Let uclient-fetch provide wget
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Busybox wget applet conflicts with the version from uclient.
Fix this by using ALTERNATIVE support for wget in busybox.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The Detection pin is at PF6 and not at PH13 like defined before. I
checked the schematics and now I am am not seeing this error message any
more:
Loading Environment from FAT... Card did not respond to voltage select!
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disable the PMIC on Olimex A13 Olinuxino, as the SPL cannot set the
core voltage correctly, which causes the board to freeze later at
kernel if CPU throttling is enabled (see below). This will almost
certainly kill the VGA output (which requires LDO3 to be set), but
this is still a better option than to disable CPU throttling for
all Cortex-A8 based devices.
[ 2.485632] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 384000 KHz
[ 2.525698] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 432000 KHz
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Instead of using a fork of the ARM trusted firmware specifically for the
Allwinner SoCs, use the official version from ARM now, this version
supports the Allwinner SoCs now and the older ATF repository is
deprecated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the uboot for the sunxi target to version 2018.11
The removed patches are applied upstream and not needed any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes two build problems introduced with the recently added new
kernel module package.
Fixes: ed2839ac41 ("kernel/modules: add kmod-pmbus-zl6100 module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds the kmod packaging for the Intersil / Zilker Labs
ZL6100 and compatible digital DC-DC controllers as well as the
core kernel module for the Power Management Bus.
Add:
kmod-pmbus-core
kmod-pmbus-zl6100
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This fixes compilation of gdb on arm64.
The kernel defines "struct sigcontext" in asm/sigcontext.h and musl libc
defines it in signal.h, which collides.
Kernel 4.14 misses the definitions of struct user_sve_header so we still
have to use the aarch64-sve-linux-sigcontext.h header file which also
provides that and make sure aarch64-sve-linux-sigcontext.h does not
provide the same headers as the kernel or musl.
Fixes: FS#2040
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set the LDFLAGS otherwise it will not get the target hardening flags or
any other generic flags provided in the LDFLAGS
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
d2e247d odhcp6c: align further with RFC8415
ce83a23 dhcpv6: avoid parsing unncessary IAs
b079733 dhcpv6: set cnt to correct IOV enum
41494da dhcpv6: get rid of request_prefix
f7437e4 dhcpv6: sanitize option request list
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The new samba36-hotplug package provides a hotplug.d script for the
"mount" subsystem. It automatically shares every mounted block device.
It works by updating /var/run/config/samba file which:
1) Is read by procd init script
2) Gets wiped on reboot providing a consistent state
3) Can be safely updated without flash wearing or conflicting with user
changes being made in /etc/config/samba
Cc: Rosy Song <rosysong@rosinson.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This will allow automation/hotplug.d scripts to store runtime shares in
the /var/run/config/samba. It's useful e.g. for USB drives that user
wants to be automatically shared.
Using /var/run/config/ provides:
1) Automated cleaning on reboots
It's important for consistency (to avoid sharing non-existing drives)
2) Safety for user non-commited changes
Automated scripts should never call "uci [foo] commit" as that could
flush incomplete config.
Another minor gain is avoiding flash wearing for runtime setup.
Cc: Rosy Song <rosysong@rosinson.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes:
1) Getting STA info with newer firmwares
2) Getting DMI / UEFI / OF data
3) Possible memory corruption in firmware loading code
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1) Using fwctx variable after brcmf_fw_request_done() was executed meant
accessing freed memory.
2) Using fwctx->completion for the wait_for_completion_timeout() call
could reuslt in NULL pointer dereference on fw loading error or if
brcmf_fw_request_done() was executed quickly enough.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from
there) to fix image generation using the image-builder.
Also remove the bootloader from DEVICE_PACKAGES and instead use the
BUILD_DEVICES directive from within the U-Boot makefile.
This fixes eva-image generation using the OpenWRT image-builder.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch deprecates the kmod-ptp-gianfar package and
introduces kmod-ptp-qoriq for 4.19+ in its place. This
has become necessary due to the linux kernel commit
ceefc71d4c05 ("ptp: rework gianfar_ptp as QorIQ common PTP driver")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
Currently busybox find and xargs conflict with the versions from
findutils package. Fix this by using ALTERNATIVES in busybox
and the related findutils (from packages feed) commit.
The conflict is due to the binaries being in the the same place
in rootfs and opkg not being happy about that.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
It seems, that since Linux 4.18-rc1 rtc-ds1307 depends on hwmon-core.
commit 6b583a64fd1e019fd01626b46892ebf2361951c5
Author: Heiner Kallweit <hkallweit1@gmail.com>
Date: Wed Sep 27 22:41:26 2017 +0200
rtc: ds1307: simplify hwmon config
We don't have to define an extra config symbol, IS_REACHABLE does
what we need. And having this config symbol just to save the few
bytes of hwmon support on non-DS3231 chips isn't worth it IMO
(especially as the symbol is set per default).
While at it, use the same dependency check for `kmod-regmap` as well, so
it's future proof as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
70f8785 zones: add zone identifying local traffic in raw OUTPUT chain
6920de7 utils: Free args in __fw3_command_pipe()
6ba9105 options: redirects: Fix possible buffer overflows
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This commit adds the nescessary settings to allow reading the uboot environment variables on the GL.iNet GL-B1300 board.
Signed-off-by: Ibrahim Tachijian <barhom@netsat.se>
This updates hostapd to version the git version from 2018-12-02 which
matches the 2.7 release.
The removed patches were are already available in the upstream code, one
additional backport is needed to fix a compile problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a big block(d) cleanup with new feature of generating "mount"
hotplug.d events.
It's an important update for those who were using mountd in the
pre-18.06 releases. Due to the mountd being replaced with blockd a
support for "mountd" hotplug.d events has been lost. It broke all kind
of shell scripts that were e.g. managing services depending on an
external USB drive availability.
This basically (re-)adds support for calling /etc/hotplug.d/mount/
scripts with ACTION ("add" or "remove") and DEVICE set.
af93f4b block(d): improve hotplug.d "mount" events for the autofs
3bb3352 blockd: unmount device explicitly when it disappears
28753b3 block: remove target directory after unmounting
c8c7ca5 block: cleanup handling "start" action of the "autofs" command
f1bb762 block: make blockd_notify() return an int instead of void
71c2bde block: generate hotplug.d mount events
30f5096 block: validate amount of arguments for the "autofs" command
dc6a462 blockd: don't reparse blob msg in the vlist callbacks
f6a9686 blockd: don't unmount device when removing it from the list
1913fea block: don't duplicate unmounting code in the mount_action()
6b445fa block: make umount_device() function more generic
a778468 block: don't duplicate mounting code in the mount_device()
5dc631d block: simplify code picking mount target directory
2971779 block: move blockd_notify() call out of the conditional blocks
b86bd6e block: fix formatting & indent in the mount_device()
e12c0d6 fstools: use EXIT_FAILURE when indicating error on exit
091aa3d fstools: guard usage of WEXITSTATUS
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit allows to use non-standard UBI volume name as the rootfs
volume in sysupgrade.
ex.:
The U-Boot on Buffalo WXR-2533DHP checks existence and checksum of
"ubi_rootfs" volume when booting, so this name is required.
OpenWrt currently provides several patches:
490-ubi-auto-attach-mtd-device-named-ubi-or-data-on-boot.patch
491-ubi-auto-create-ubiblock-device-for-rootfs.patch
492-try-auto-mounting-ubi0-rootfs-in-init-do_mounts.c.patch
to facilitate ubi rootfs automount. However the upstream kernel
also supports the means of booting from a fully custom ubi
partition name and ubi volume name via bootargs/kernel's cmdline
parameters:
ubi.mtd=mtd_partition_name
ubi.block=rootfs_volume_name
root=/dev/ubiblock$X_$Y
For more information and examples visit the wiki over at linux-mtd:
<http://www.linux-mtd.infradead.org/faq/ubifs.html>
<http://www.linux-mtd.infradead.org/doc/ubi.html>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
Update busybox to 1.30.0.
Refresh patches.
Leave new features disabled by default.
Config refreshed via:
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-1.30.0
make package/busybox/compile
cd package/utils/busybox
./convert_defaults.pl < ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-1.30.0/.config > Config-defaults.in
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
check_signature is a bool option and doesn't take any arguments. The
presence of the 1 falsely suggests setting it to 0 disables the check,
while the option actually needs to be removed or commented out to be
disabled. So remove the argument to make it more clear.
Fixes: beca028bd6 ("build: add integration for managing opkg package feed keys")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Before installing an interface triggger check if an interface
trigger for the interface is already in place.
This avoids installing identical interface triggers for a given
interface
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
omcproxy will not start up if either the downlink or uplink interface is
not up at boottime as the interface triggers are not correctly
installed.
Further rework omcproxy init to make use of network functions defined
in network.sh; set proper family and proto options in procd firewall
rules.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
dd508af iwinfo: fix QCA9984 vendor id
0eaabf1 iwinfo: add device id for Atheros AR9287
6e998ec iwinfo: add device id for MediaTek MT7612E
5aa8c54 libiwinfo: nl80211: add mesh stats on assoclist.
77a9e98 iwinfo: Add Mikrotik R11e-2HPnD and R11e-5HacT to hardware list
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit fd569e5e9d.
After an extra review & discussion few concerns were raised regarding
that feature:
1) It reacts to hotplug.d "block" events instead of more accurate (but
currently unavailable) "mount" events.
2) It requires *something* to mount block device before samba hotplug.d
gets fired. Otherwise samba_add_section() will just return.
3) It doesn't reload Samba which some users may expect
4) It operates on /etc/ which is not a right place for autogenerated
ephemeral config.
5) It doesn't include any cleanup for non-existing shares.
Cc: Rosy Song <rosysong@rosinson.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
417ab77 mt7603: improve recovery from PSE reset failure
fea7ad8 mt76: move mt76x02_phy_get_min_avg_rssi to mt76 core
9d009be mt7603: add dynamic sensitivity tuning based on false CCA events
2c8e9ac mt7603: initialize channel maximum power from eeprom data
b2cc29b mt76: move mt76x02_get_txpower to mt76 core
6203d46 mt7603: add support for setting transmit power
294e095 mt7603: reset DMA scheduler on MT7628
8178f0d mt7603: apply efuse data only when it exists
e67e551 mt76: dma: remove napi from mt76_dma_rx_fill signature
0490bd2 mt76: usb: do not build the skb if reported len does not fit in buf_size
eb076ae mt76: Add missing include of linux/module.h
1d2819e mt76: fix typo in mt76x02_check_mac_err routine
9c9fae3 mt76: mac: run mt76x02_mac_work routine atomically
6be90b6 mt76: usb: avoid queue/status spinlocks while passing tx status to mac80211
40dad32 mt76x0: pci: fix ACS support
d94e9c4 mt76x02: do not set protection on set_rts_threshold callback
0d83d73 mt76x02: fixup MT_PROT_RATE_* defines
628f8d7 mt76x02: set protection according to ht operation element
f7d8c17 mt76x0: configure MT_VHT_HT_FBK_CFG1
10f57cf mt76x2: add static qualifier to mt76x2_init_hardware
37b2ad3 mt76: dfs: run mt76x02_dfs_set_domain atomically
51b6daf mt76x2: init: set default value for MT_TX_LINK_CFG
9661da4 mt76: add energy detect CCA support to mt76x{0,2}e drivers
876d0e9 mt76: mac: minor optimizations in mt76x02_mac_tx_rate_val
c78e317 mt76: dma: do not build skb if reported len does not fit in buf_size
3598046 mt76: mmio: introduce mt76x02_check_tx_hang watchdog
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since kernel 4.18 support for Qualcomm glue layer was
moved from DWC3 OF Simple to a separate DWC3 QCOM module.
So lets add it and make it depend on 4.19 kernel and make
sure that DWC3 OF Simple is not included if 4.19 is used.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This version removes a lot of unusefull warnings that would quickly overflow the dmesg.
Warnings like this:
ath10k_ahb a800000.wifi: Invalid legacy rate 26 peer stats
ath10k_ahb a000000.wifi: Invalid VHT mcs 15 peer stats
On this version I only had 2 warnings at all.
Tested on 8devices Jalapeno.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Based on the process of discovery in
https://github.com/openwrt/openwrt/pull/1613, it has become clear
that (at least) the PowerCloud System CR5000 was unable to get
working 5GHz wireless (PCIe) because AH_USE_EEPROM was unconditionally
masked out, not only when qca,noeeprom was in the DTS.
This patch moves mask AH_USE_EEPROM into the if ... qca,noeeprom
OF test.
Thanks to Christian Lampartar (@chunkeey) for the heavy lifting and help.
Patch has been prepared for upstream and will be submitted after review
by @chunkeey and @xdarklight.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
GCC 8.0+ <https://gcc.gnu.org/gcc-8/changes.html> introduces a new
warning about unsafe macros expanding to multiple statements used
as a body of a statement such as if, else, while, switch, or for.
In combination with -Werror this can cause the compilation to fail:
|In file included from xmalloc.c:37:
|xmalloc.c: In function 'xmalloc':
|system.h:39:2: error: macro expands to multiple statements [-Werror=multistatement-macros]
| fflush(stdout); \
| ^~~~~~
|xmalloc.c:52:5: note: in expansion of macro 'error'
| error (EXIT_FAILURE, 0, _("memory exhausted"));
| ^~~~~
|xmalloc.c:51:3: note: some parts of macro expansion are not guarded by this 'if' clause
| if (p == NULL)
| ^~
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
67ce93e Fix compile error on kernel 4.15+
c1345bb Change driver version to 10.3.8.0-20181210.
9cb815b Upgrade 88W8997 firmware to 8.4.4.6.
433fc6d Fix non-backport use of nla_parse before 4.12.0
3b36e21 Use wiphy_to_ieee80211_hw() instead of wiphy_priv()
97ebcfa Change driver version to 10.3.8.0-20181120.
f000953 Upgrade 88W8997 firmware to 8.4.4.4.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Depending on the global nls support configuration in the buildroot, the
linked libelf.so library might depend on libintl.so.
Import the nls.mk helper to set library prefixes and flags accordingly
in this case.
Ref: https://github.com/openwrt/packages/issues/7728#issuecomment-448760140
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When building with full lagnuage support, libelf.so will depend on and
link with libintl.so so we need to change the pkg-config template to
reflect this library dependency.
Also change the Makefile to only pass --disable-nls to configure when
the full nls support is actually disabled in the buildroot config.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The iproute2 build system links libelf support to every utility while only
the tc program actually requires libelf specific functionality.
Unfortunately the BPF ELF functionality is not confined into an own
compilation unit but added to the existing bpf.c sources of the shared
static libutil.a, causing every iproute2 applet to pick up an implicit
libelf.so dependency.
In order to avoid this requirement, patch the iproute2 build system to
create both a libutil.a and a libutil-elf.a, with the former being built
without libelf functionality and to only link the tc applet with the libelf
enabled libutil.
Finally, make the tc package depend on libelf to solve compilation errors.
Ref: https://github.com/openwrt/packages/issues/7728
Fixes: FS#2011
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support other packages using pkg-config to query existence and details of
libelf and libdw libraries at build time.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This file is needed to properly use the tc ematch modules present in
kmod-sched-core and kmod-sched. It is a read-only index file of ematch
methods used only by tc.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The LS1021A-IoT gateway reference design based on the
QorIQ LS1021A processor is a purpose-built, small
footprint hardware platform with a wide array of
high-speed connectivity and low-speed serial interfaces
to support secure delivery of IoT services for home,
business or other commercial location.
- Combines standards-based, open source software with a
feature-rich IoT gateway design to establish a common,
open framework for secured IoT service delivery and
management.
- Provides a wide assortment of high-speed and serial-based
connectivity in a compact, highly secure design.
- High efficiency through the use of the Arm-based QorIQ
LS1021A embedded processor.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
It seems, that since Linux 4.18-rc2 ci_hdrc depends on ulpi.
commit a930d8bd94d8db7715d1af74299f710b1fb22fc8
Author: Fabio Estevam <fabio.estevam@nxp.com>
Date: Wed Jul 4 10:09:58 2018 -0300
usb: chipidea: Always build ULPI code
Commit 03e6275ae381 ("usb: chipidea: Fix ULPI on imx51") causes a kernel
hang on imx51 systems that use the ULPI interface and do not select the
CONFIG_USB_CHIPIDEA_ULPI option.
In order to avoid such potential misuse, let's always build the
chipidea ULPI code into the final ci_hdrc object.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
After changing board names to DT compat string, we also need to
adjust the script which generates uboot-env configuration files.
Fixes: e880a30549 ("mxs: use generic sysinfo board detection")
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
According to https://github.com/openwrt/openwrt/pull/1527, support
for the Buffalo BHR-4GRV2 in ath79 requires repartitioning from
an initramfs image, make this easier by supporting uboot-envtools
support out of the box.
Build tested, but not runtime tested.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Port support for the Buffalo WZR-HP-AG300H from the ar71xx target to
ath79 as well.
Build- and runtime tested on the Buffalo WZR-HP-AG300H.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Interface triggers are installed by the dropbear init script in case an
interface is configured for a given dropbear uci section.
As dropbear is started after network the interface trigger event can be
missed during a small window; this is especially the case if lan is
specified as interface.
Fix this by starting dropbear before network so no interface trigger
is missed. As dropbear is started earlier than netifd add a boot function
to avoid the usage of network.sh functions as call to such functions will
fail at boottime.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
In the upstream netdev led trigger the one mode file was replaced by 3
files named rx, tx and link. Fix the netdev trigger configuration code
to use the modified API.
Fixes: aa3b6a08c5 ("kernel: Replace ledtrig-netdev with upstream backport")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 216397b812.
Due to:
Package ip-tiny is missing dependencies for the following libraries:
libelf.so.1
Makefile:187: recipe for target '/var/lib/buildbot/slaves/slave-lede-builds4/mips_24kc/build/sdk/bin/packages/mips_24kc/base/ip-tiny_4.19.0-6_mips_24kc.ipk' failed
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The eapol-test application also uses the code with the newly activated
ubus support, add the missing dependency.
Fixes: f5753aae23 ("hostapd: add support for WPS pushbutton station")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mbedtls uses some instructions introduced in ARMv6 which are not
available in older architectures.
Fixes: 3f7dd06fd8 ("mbedtls: Update to 2.14.1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update mbedtls to 2.14.1
This fixes:
* CVE-2018-19608: Local timing attack on RSA decryption
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[Update to 2.14.1]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes these warnings:
swlib.c:455:18: warning: implicit declaration of function 'isspace'
swlib.c:461:9: warning: implicit declaration of function 'isdigit'
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Added two upstream mailing list patches that fix behavior under big endian
systems. Issue was present since version 1.11.0.
Tested on Turris Omnia.
Original discussion: https://github.com/openwrt/openwrt/pull/1575
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Use a forked version of the rtl8812au driver that works better
with OpenWRT (fix compile bugs, fix phy MAC address, etc)
Signed-off-by: Ben Greear <greearb@candelatech.com>
[update to 2018-11-16, replace rtw_byteorder.h, rename folder]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the ath10k-ct driver to the version from 2018-12-11 and
selects the ath10k-ct version based on kernel 4.19 by default.
CONFIG_ATH10K_CE was introduced between kernel 4.16 and 4.19 and is a
mandatory option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In mainline kernel commit 02c7b25e5f5 ("netfilter: nf_tables: build-in
filter chain type") all chain filters were merged into one file and into
one kernel module to save some memory. The code protected by these
configuration options CONFIG_NF_TABLES_BRIDGE, CONFIG_NF_TABLES_IPV4,
CONFIG_NF_TABLES_ARP, CONFIG_NF_TABLES_IPV6, CONFIG_NF_TABLES_NETDEV and
CONFIG_NF_TABLES_INET was merged into the nft_chain_filter.c file which
is now always compiled into the nf_tables.ko file.
This only happened in kernel 4.19 and OpenWrt has to select these as
modules in older kennel versions. Mark them as build-in in the kernel
4.19 specific kernel configuration file which will then not be
overwritten by the package specific settings which try to make them
modular again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_HW_RANDOM_TPM does not activate a separate kernel module any
more, but it only activates the random code in the tpm.ko.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The video-videobuf2 kernel modules were moved to a new folder in kernel
4.19. videobuf2-v4l2.ko is only available since kernel 4.4, blacklist
this kmod completely on kernel 3.18.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The x86 optimized cryptographic algorithm kernel modules now mostly use
crypto_simd.ko instead of lrw.ko in kernel 4.19. Add the new module to
the kmod-crypto-misc package.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The asn1_decoder.ko module is needed by the kmod-nf-nathelper-extra
package in kernel 4.19, extract it and add the missing dependencies.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kernel interface changed with kernel 4.19, it does not accept raw GPIO
numbers any more. Deactivate these drivers on kernel 4.19 for now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The r8169 driver uses the phy lib with the realtek phy driver in kernel
4.19 instead of integrating the phy driver into the mac driver.
Add the new phy driver and add this missing dependency.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ledtrig-netdev was added to upstream Linux kernel 4.16, replace our
own version with the patch based on the upstream version.
This will remove the ledtrig-netdev support from kernel 3.18, because I
not want to spend time on backporting it to 3.18. This will make it
easier to use the upstream version with kernel 4.19, by just not
applying this patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
63843750 Update manual pages
27801e98 Bump up version number to 1.35.1
60e020a8 nghttpx: Fix broken trailing slash handling
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The above options were incorrectly changed to required tags. Make them
optional again.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Backport upstream patch fixing incorrect passing of -lxtables to
LDFLAGS instead of LDLIBS in the tc/Makefile
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This updates the backports package used in mac80211 to version 4.19.7-1
which is based on kernel 4.19.7. This integrates all the stable fixes
introduces in this kernel version.
The deleted patches are not needed any more because they are either
included in the upstream Linux kernel 4.19.7 or in backports 4.19.7-1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In hack/904-debloat_dma_buf.patch, DMA_SHARED_BUFFER is changed from
bool to tristate. As this patch is not applied to external kernel
sources, build fails if kmod-dma-buf is enabled. Fix this by only
including the module file if CONFIG_EXTERNAL_KERNEL_TREE and
CONFIG_KERNEL_GIT_CLONE_URI are not enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
3aa81d0 file: access exec timeout via daemon ops structure
7235f34 plugin: store pointer to exec timeout value in the ops structure
ccd7c0a treewide: rename exec_timeout to rpc_exec_timeout
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
During upstream removal of conditional ipv6 support an order swap error
was made in a ternary operator usage.
This patch sent upstream.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The argument to print_0xhex is converted to unsigned long long
so the format string give for normal printout has to be some
variant of %llx. Backport the patch as otherwise, bogus values
will be printed on 32 bit platforms.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This partitialy reverts commit ccab68f2d3.
Registering the GPIO chip without a parent device completely breaks the
ath9k GPIOs for device tree targets.
As long as boards using the devicetree don't have the gpio-controller
property set for the ath9k node, the unloading of the driver works as
expected.
Register the GPIO chip with the ath9k device as parent only for OF
targets to find a trade-off between the needs of driver developers and
the broken LEDs and buttons seen by users.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Beside one exception, no one took care of these two remaining boards
still using the legacy image build code during the last two years.
Since OpenWrt 14.07 the ALLNET ALL0239-3G image building is broken.
The Sitecom WL-341 v3 image build code looks pretty hackish and broken.
It's questionable if the legacy image works as all.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Support other packages using pkg-config to query existence and details of
libelf and libdw libraries at build time.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
similar to hostapd, also add a ubus interface for wpa_supplicant
which will allow handling WPS push-button just as it works for hostapd.
In order to have wpa_supplicant running without any network
configuration (so you can use it to retrieve credentials via WPS),
configure wifi-iface in /etc/config/wireless:
config wifi-iface 'default_radio0'
option device 'radio0'
option network 'wwan'
option mode 'sta'
option encryption 'wps'
This section will automatically be edited if credentials have
successfully been acquired via WPS.
Size difference (mips_24kc): roughly +4kb for the 'full' variants of
wpa_supplicant and wpad which do support WPS.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch updates the uboot-fritz4040 package to the latest version.
The portability and private-libgcc patches, as well as the
upload-to-f4040.sh script have been added to the upstream repository.
Furthermore, the upload-to-f4040 has been updated to take the first
parameter as the file it is supposed to flash, otherwise it defaults
to the previous "uboot-fritz4040.bin". Furthermore the error messages
have been improved and ftp will now dump some "progress information"
to the user's console.
Also included is support for gcc 8+ and a fix for the obnoxous error
that currently breaks the builders:
| fritz/src/lzma2eva.c:23:30: fatal error: zlib.h: No such file or directory
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Backport upstream commits. Most interesting 122392e which changes how
SERVFAIL is handled especially in event of genuine server down/failure
scenarios with multiple servers. a799ca0 also interesting in that
answered received via TCP are now cached, DNSSEC typically using TCP
meant until now answers weren't cached, hence reducing performance.
59e4703 Free config file values on parsing errors.
48d12f1 Remove the NO_FORK compile-time option, and support for uclinux.
122392e Revert 68f6312d4bae30b78daafcd6f51dc441b8685b1e
3a5a84c Fix Makefile lines generating UBUS linker config.
24b8760 Do not rely on dead code elimination, use array instead. Make options bits derived from size and count. Use size of option bits and last supported bit in computation. No new change would be required when new options are added. Just change OPT_LAST constant.
6f7812d Fix spurious AD flags in some DNS replies from local config.
cbb5b17 Fix logging in cf5984367bc6a949e3803a576512c5a7bc48ebab
cf59843 Don't forward *.bind/*.server queries upstream
ee87504 Remove ability to compile without IPv6 support.
a220545 Ensure that AD bit is reset on answers from --address=/<domain>/<address>.
a799ca0 Impove cache behaviour for TCP connections.
Along with an additional patch to fix compilation without DHCPv6, sent
upstream.
I've been running this for aaaages without obvious issue hence brave
step of opening to wider openwrt community.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This reverts commit a6a8fe0be5.
buildbot found an error
option.c: In function 'dhcp_context_free':
option.c:1042:15: error: 'struct dhcp_context' has no member named 'template_interface'
free(ctx->template_interface);
revert for the moment
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Backport upstream commits. Most interesting 122392e which changes how
SERVFAIL is handled especially in event of genuine server down/failure
scenarios with multiple servers. a799ca0 also interesting in that
answered received via TCP are now cached, DNSSEC typically using TCP
meant until now answers weren't cached, hence reducing performance.
59e4703 Free config file values on parsing errors.
48d12f1 Remove the NO_FORK compile-time option, and support for uclinux.
122392e Revert 68f6312d4bae30b78daafcd6f51dc441b8685b1e
3a5a84c Fix Makefile lines generating UBUS linker config.
24b8760 Do not rely on dead code elimination, use array instead. Make options bits derived from size and count. Use size of option bits and last supported bit in computation. No new change would be required when new options are added. Just change OPT_LAST constant.
6f7812d Fix spurious AD flags in some DNS replies from local config.
cbb5b17 Fix logging in cf5984367bc6a949e3803a576512c5a7bc48ebab
cf59843 Don't forward *.bind/*.server queries upstream
ee87504 Remove ability to compile without IPv6 support.
a220545 Ensure that AD bit is reset on answers from --address=/<domain>/<address>.
a799ca0 Impove cache behaviour for TCP connections.
I've been running this for aaaages without obvious issue hence brave
step of opening to wider openwrt community.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Openwrt no longer uses and has not used since 5acfe55d71 Jun 2016 the
timestamp file (/etc/dnsmasq.time) method of resolving the dnssec/ntp
dnslookup chicken/egg problem, having used signals from ntp since that
change.
Drop the 'dnssec-improve-timestamp-heuristic' patch since it is neither
used nor sent upstream. One less thing to refresh & maintain.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When '-k' is used, sysupgrade inserts into backup a new file
/etc/backup/installed_packages.txt which contains pkgname and origin (rom,
overlay, unknown) without touching rootfs.
It's mainly used to reinstall all extra packages:
# opkg update
# grep "\toverlay" /etc/backup/installed_packages.txt | cut -f1 | xargs -r opkg install
# rm /etc/backup/installed_packages.txt
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Add sysupgrade '-o' option in order to include all overlay files in
backup, except for those that are from packages but including files
listed in conffiles, sysupgrade.conf or /lib/upgrade/keep.d.
With '-u' option, it will skip files equals to /rom and conffiles that
were not changed.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
With '-u', for a file /aaa/bbb/ccc enlisted for backup,
it will only get into backup if /rom/aaa/bbb/ccc does not
exist or /aaa/bbb/ccc is different from /rom/aaa/bbb/ccc.
It also works with '-c', but only effective for files touched
but not modified.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Renamed add_uci_conffiles to add_conffiles as it includes
any conffiles listed, not only UCI ones.
Make do_save_conffiles arg mandatory
Allow other options after -l (like -c)
Do not use stdout for error messages (fixes backup to stdout)
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
This now matches what was generated locally on my PC and the file on the
mirror server.
Fixes: 575d0240f9 ("ath10k-firmware: update board-2.bin for community firmwares")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Drop 030-extensions-libxt_bpf-Fix-build-with-old-kernel-versi.patch as pushed upstream
Added patches :
001-extensions_format-security_fixes_in_libip.patch
002-include_fix_build_with_kernel_headers_before_4_2.patch
101-remove-register-check.patch
The first and the second patch are upsteam fixes for compilation errors.
The third patch remove check if one target lib is already registred; this is caused by
shared libs that are loaded before the iptables execution.
Iptables changelog:
bba6bc6 (tag: v1.8.2) configure: bump versions for 1.8.2 release
61d6c38 xtables: add 'printf' attribute to xlate_add
5edb249 libxtables: xlate: init buffer to zero
9afd2a6 tests: shell: fix expected arptables-save output
6387941 arptables: fix --version info
d703c1f arptables: ignore --table argument.
d5754e3 arptables: make uni/multicast mac masks static
1b63e66 arptables: add test cases
5aecb2d arptables: pre-init hlen and ethertype
9677ed1 arptables: fix src/dst mac handling
ab0b6d5 arptables: fix target ip offset
c0c75ce arptables: fix -s/-d handling for negation and mask
3ac65af arptables: add basic test infra for arptables-nft
e31564f arptables: fix rule deletion/compare
2345ff6 arptables: remove code that is also commented-out in original arptables
50c2397 arptables-save: add -c option, like xtables-save
d9a518e arptables: use ->save for arptables-save, like xtables
5a52e6a extensions: test protocol and interface negation
85d7df9 xtables: Fix error return code in nft_chain_user_rename()
3ccb443 xtables: Clarify error message when deleting by index
95db364 xtables: Fix typo in do_command() error message
5f508b7 ebtables: use extrapositioned negation consistently
583b27e ebtables-save: add -c option, using xtables-style counters
e6723ab nft: add NFT_TABLE_* enumeration
21ec111 nft: replace nft_chain_dump() by nft_chain_list_get()
05947c8 iptables-nft: fix -f fragment option
7bd9feb libxtables: add and use mac print helpers
a10eb88 extensions: libebt_ip: fix tos negation
9b127b7 extensions: libebt_ip6: fix ip6-dport negation
c59ba1b xtables-nft: make -Z option work
1bf4a13 nft: add missing error string
a9f9377 iptables-tests: add % to run iptables commands
b81c8da iptables-tests: do not append xtables-multi to external commands
edf2b7c ebtables-nft: add arpreply target
2d1372e ebtables: add redirect test case
c3e8dbd ebtables: add test cases
cd90cef ebtables: relax -t table restriction, add snat/dnat test cases
fd95f1f ebtables: fix -j CONTINUE handling for add/delete
fb747f8 tests: add basic ebtables test support
d4bc5a3 iptables-nft: fix bogus handling of zero saddr/daddr
9ff9915 iptables-test: fix netns test
8c918db xtables: Fix for matching rules with wildcard interfaces
b2fc2a3 extensions: limit: unbreak build without libnftnl
682f39a xtables: Fix for spurious errors from iptables-translate
90f7dc3 (tag: v1.8.1) configure: bump versions for 1.8.1 release
0123183 iptables-test: add -N option to exercise netns removal path
abae556 libxtables: expose new etherdb lookup function through libxtables API
c2d9ed9 libxtables: prefix exported new functions for etherdb lookups
5a44360 Revert "extensions: libxt_quota: Allow setting the remaining quota"
2673faf xtables: Remove target_maxnamelen field
8ca3436 extensions: cgroup: fix option parsing for v2
0a8f2bc extensions: libxt_quota: Allow setting the remaining quota
b373a91 nft-shared: Use xtables_calloc()
5a40961 arptables: Use the shared nft_ipv46_parse_target()
9f07503 Combine parse_target() and command_jump() implementations
7373297 Combine command_match() implementations
a76ba54 libiptc: NULL-terminate errorname
a3716cc libxtables: Check extension real_name length
0195b64 iptables: Gitignore xtables-{legacy, nft}-multi scripts
671e40a xtables: Drop pointless check
7c9a152 arptables: Fix incorrect strcmp() in nft_arp_rule_find()
11e91a4 xtables: Don't read garbage in nft_ipv4_parse_payload()
d95c1e8 libxtables: Use posix_spawn() instead of vfork()
7e50eba Fix a few cases of pointless assignments
f40ce2d extensions: libebt_ip{, 6}: Drop pointless error checking
47fb86c nft-arp: Drop ineffective conditional
80aae9b iptables: Use print_ifaces() from xtables
8da04ff Share print_ipv{4,6}_addr() from xtables
b686594 iptables-apply: Replace signal numbers by names
f175dee iptables-apply: Quote strings passed to echo
52aa150 nfnl_osf: Replace deprecated nfnl_talk() by nfnl_query()
61ebf3f libxtables: Don't read garbage in xtables_strtoui()
ab639f2 libxtables: Avoid calling memcpy() with NULL source
22ef371 libiptc: Simplify alloc_handle() function signature
6b7145f libxt_time: Drop initialization of variable 'year'
749d3c2 libxt_ipvs: Avoid potential buffer overrun
8e798e0 libxt_conntrack: Avoid potential buffer overrun
74eb239 libxt_conntrack: Version 0 does not support XT_CONNTRACK_DIRECTION
d0c1f1b libxt_LED: Avoid string overrun while parsing led-trigger-id
23ef6f0 xtables: Remove unused variable in nft_is_table_compatible()
4e499d5 ip{, 6}tables-restore: Fix for uninitialized array 'curtable'
1788f54 Mark fall through cases in switch() statements
31f1434 libxtables: Integrate getethertype.c from xtables core
7ae4fb1 xtables: Fix for wrong assert() in __nft_table_flush()
8c786a3 nfnl_osf: Drop pointless check in xt_osf_strchr()
6fc7762 libxt_string: Fix array out of bounds check
2a68be1 xtables-save: Ignore uninteresting tables
f9efc8c extensions: add cgroup revision 2
9b8cb16 extensions: REJECT: Merge reject tables
56d7ab4 libxt_string: Avoid potential array out of bounds access
bfd41c8 ebtables: Fix for potential array boundary overstep
e6f9867 libiptc: Avoid side-effect in memset() calls
4144571 libxtables: Fix potential array overrun in xtables_option_parse()
9242b5d xtables: Accept --wait in iptables-nft-restore
c9f4f04 xtables: Don't check all rules for being compatible
15606f2 doc: Improve layout of u32 instructions
7345037 xtables-restore: Fix flushing referenced custom chains
7df11d1 xtables: Drop use of IP6T_F_PROTO
b6a06c1 xtables: Align return codes with legacy iptables
3bb497c xtables: Fix for deleting rules with comment
0800d9b ip6tables-translate: Fix libip6t_mh.txlate test
4cf650c ebtables-translate: Fix for libebt_limit.txlate
783e9c2 xtables: Add missing deinitialization
9771d06 ebtables: Review match/target lookup once more
85ed1ab extensions: libebt_mark: Drop mark_supplied check
6a46ca0 xtables: Add a few missing exit calls
acde6be ebtables-translate: Fix segfault while parsing extension options
2c4e4d2 ebtables: trivial: Leverage C99-style initializers a bit more
9f5b28a xlate-test: Fix for calling wrong command name
1a878a7 extensions: AUDIT: Provide translation
5ee03e6 xtables: Use meta l4proto for -p match
37b68b2 xtables: Fix for segfault when registering hashlimit extension
92f7b04 xtables: Fix for segfault in iptables-nft
294f9ef ebtables: Fix entries count in chain listing
6f29aa8 xtables: Make 'iptables -S nonexisting' return non-zero
7bccf30 ebtables: Fix for listing of non-existent chains
3d9a13d xtables: Fix for no output in iptables-nft -S
a33c6fd arptables: Drop extensions/libxt_mangle.c
02b8097 ebtables: Merge libebt_limit.c into libxt_limit.c
5de8dcf xtables: Use native nftables limit expression
514de48 ebtables: Remove flags misinterpretations
528cbf9 xtables: Fix for wrong counter format in -S output
9ca32c4 xtables: Don't pass full invflags to add_compat()
e055aeb xtables: Improve xtables-monitor first impression
b925733 tests: Fix skipping for recent nft-only tests
277f374 xtables: Spelling fixes in xtables-monitor
a9d9f64 xtables: Fix potential segfault in nft_rule_append()
fbf0bf7 tests: Add ebtables-{save,restore} testcases
f1d8508 tests: Add arptables-{save,restore} testcases
63c3dae xtables: Implement arptables-{save,restore}
aa7fb04 ebtables: Review match/target lookup
3f123dc ebtables-restore: Use xtables_restore_parse()
295d5a8 xtables-restore: Make COMMIT support configurable
1679b2c xtables-restore: Improve user-defined chain detection
2ce9f65 xtables: Match verbose ip{,6}tables output with legacy
cd79556 xtables: Reserve space for 'opt' column in ip6tables output
0357254 xtables: Print error when listing non-existent chains
206033e xtables: Fix for no output on first iptables-nft invocation
a0698de xtables: Do not count rules as chain references
d11b6b8 arptables: Fix jumps into user-defined chains
3f27955 arptables: Fix opcode printing in numeric output
f988fe4 xtables: Fix symlinks/names for ebtables-{save, restore}
3319c61 ebtables: Support --init-table command
3ec8aac arptables: Print policy only for base chains
83bc189 arptables: Fix for trailing spaces in output
aaed1b6 arptables: Fix memleaks in do_commandarp()
d67d85d ebtables: Print non-standard target parameters
2e478e9 ebtables: Fix match_list insertion
a192f03 ebtables: Fix for wrong program name in error messages
a2ed880 xshared: Consolidate argv construction routines
1cc0918 xshared: Consolidate parse_counters()
78b9d43 Consolidate DEBUGP macros
14ad525 xtables: Fix program name in xtables_error()
f7bbdb0 xtables: Use correct built-in chain count
ae574b2 xtables: Fix compilation with NLDEBUG defined
82d278c xtables: Free chains in NFT_COMPAT_CHAIN_ADD jobs
c2895ea xtables: Free chains in NFT_COMPAT_CHAIN_USER_DEL jobs
89d3443 xtables: Fix for nft_rule_flush() returning garbage
c259447 xtables: Allocate rule cache just once
ed30b93 nft: don't print rule counters unless verbose
31e4b59 iptables-restore: free the table lock when skipping a table
f8e29a1 xtables: avoid bogus 'is incompatible' warning
6ea7579 nft: decode meta l4proto
922508e xtables: implement ebtables-{save,restore}
25ef908 xtables: introduce nft_init_eb()
de8574a xtables: parameter to add_argv() may be const
6f60f22 xtables: pass format to nft_rule_save()
f3b772c xtables: introduce save_chain callback
fa1681f xtables: rename {print,save}_rule functions
444d581 xtables: get rid of nft_ipv{4,6}_save_counters()
34e1e23 xtables: eliminate nft_ipv{4,6}_rule_find()
de782e8 xtables: merge nft_ipv{4,6}_parse_target()
ae8eece xtables: get rid of nft_ipv{4,6}_print_header()
2687794 xtables: arp: make rule_to_cs callback private
1bf73c4 xtables: Use new callbacks in nft_rule_print_save()
1866625 xtables: introduce rule_to_cs/clear_cs callbacks
0589457 xtables: simplify struct nft_xt_ctx
d9c6a5d xtables: merge {ip,arp}tables_command_state structs
87b5b9e iptables: replace memset by c99-style initializers
907da5c xtables: fix crash if nft_rule_list_get() fails
565a223 xtables: Support nft suffix for arptables and ebtables
c468f01 tests: check iptables retval, not echo
47d1484 iptables: tests: add test for iptables-save and iptables-restore
e4e0704 extensions: don't bother to build libebt/libarp extensions if nft backend was disabled
17c66a5 iptables: tests: shell: Add README
6c2118c (tag: v1.8.0) configure: bump version and libnftnl dependency
7b66fc2 man: clarify translate tools do not modify any state
f7fec51 xtables-monitor: add --version option
b470b8e xtables-legacy: fix argv0 name for ip6tables-legacy
2028e54 xtables: display legacy/nf_tables flavor in error messages, too
fd8d7d7 ebtables-nft: add stp match
f15639b tests: add script that mimics firewalld startup
27f7db2 tests: fix variable name to multi-binary
2a89ec5 tests: add a few simple tests for list/new/delete
37d9d5b ebtables-nft: make -L, -X CHAINNAME work
816bd1f ebtables-nft: remove exec_style
b81708f ebtables-nft: don't crash on ebtables -X
de02a75 doc: fix some spellos and the dash escape
dcf4529 tests: add firewalld default ruleset from fedora 27
f23abd5 tests: add another ipv4 only ruleset
ed9cfe1 tests: add initial save/restore test cases
9933dc5 tests: adapt test suite to run with legacy+nftables based binaries
be70918 xtables: rename xt-multi binaries to -nft, -legacy
d49ba50 xtables-restore: init table before processing policies
344c6eb doc: Fix spelling error in hashlimit section
e063873 tests: make duplicate test work
d26c538 xtables: add xtables-monitor
db84371 xtables: translate nft meta trace set 1 to -j TRACE
20eac2a xtables: warn in case old-style (set/getsockopt) tables exist
c9f5e18 xtables: add nf_tables vs. legacy postfix to version strings
e5fed16 iptables8.in: Update coreteam names
672accf include: update kernel netfilter header files
856a875 xtables: silence two compiler warnings
ae6e159 xtables: remove dead code inherited from ebtables
107b7eb configure: add -Wlogical-op warning to cflags
bc7f49d ebtables-translate: remove --change-counters code
38b4166 iptables: tests: shell: add shell test-suite
1e6427a xtables-compat: skip invalid tables
cb368b6 xtables: more error printing fixes
b1b828f xtables: homogenize error message
4caa559 xtables: initialize basechains for rule flush command too
9b89622 xtables: rework rule cache logic
01e25e2 xtables: add chain cache
8d190e9 xtables: initialize basechains only once on ruleset restore
0a86351 xtables-compat: ignore '+' interface name
125d1ce xtables-compat: append all errors into single line
437746c xtables: extended error reporting
d1c79cd xtables: allocate struct xt_comment_info for comments
4e20209 xtables: use libnftnl batch API
49709e2 xtables-compat: remove nft_is_ruleset_compatible
03e1377 xtables: allow dumping of chains in specific table
94fd83d xtables: inconsistent error reporting for -X and no empty chain
c4f1622 ebtables-compat: add arp match extension
24ce746 ebtables-compat: add redirect match extension
84c04e3 ebtables-compat: add nat match extensions
14ec998 xtables-compat: ebtables: prefer snprintf to strncpy
5e2b473 xtables-compat: extend generic tests for masks and wildcards
1a696c9 libxtables: store all requested match types
bb436ce xtables-compat: ip6table-save: fix save of ip6 address masks
6454d7d ebtables-translate: suppress redundant protocols
07f4ca9 xtables-compat: ebtables: allow checking for zero-mac
0ca2d2a xtables-compat: ebtables: add helpers to print interface and mac addresses
3d9f300 xtables-compat: ebtables: remove interface masks from ebt_entry struct
20e2758 xtables-compat: ebtables: fix logical interface negation
2682bb0 xtables-compat: ebtables: add and use helper to parse all interface names
564862d xtables-compat: ebtables: split match/target print from nft_bridge_print_firewall
0ae81d0 xtables-compat: ebtables: kill ebtables_command_state
651cfee xtables-compat: pass correct table skeleton
652b98e xtables-compat: fix wildcard detection
49f4993 extensions: libip6t_srh.t: Add test cases for psid, nsid, and lsid
429143b extensions: libxt_CONNMARK: incorrect translation after v2
db7b4e0 extensions: libxt_CONNMARK: Support bit-shifting for --restore,set and save-mark
155e1c0 extensions: libip6t_srh: support matching previous, next and last SID
f4ffda1 extensions: libipt_DNAT: tests added for shifted portmap range
6a9ffb1 xtables-compat-restore: flush table and its content with no -n
07ae37c xtables-compat: fix bogus error with -X and no user-defined chains
df3d92b xtables-compat-restore: flush user-defined chains with -n
ca16584 xtables-compat-restore: flush rules and delete user-defined chains
ac1e85a extensions: libipt_DNAT: use size of nf_nat_range2 for rev2
e25d99a xtables-compat: pass larger socket buffer
838746e xtables-compat: xtables-save: don't return 1
2211679 xtables-compat: ebtables: support concurrent option
a77a7d8 iptables-test: fix bug with rateest
de87405 xtables-compat: fix ipv4 frag (-f)
c7b2fd6 xtables-compat: also check tg2->userspacesize
5685938 xtables-compat: avoid unneeded bitwise ops
b9d7b49 xtables-compat: restore: sync options with iptables-restore
c0ef861 extensions: add xlate test for ipables -f
d79a7f1 xtables-compat: output -s,d first during save, just like iptables
d1eb4d5 iptables-compat: chains are purge out already from table flush
09f0d47 iptables-compat: do not fail on restore if user chain exists
8798eb8 iptables-compat: remove non-batching routines
b633ef9 xtables.conf: fix hook skeletons
7af2178 xtables-compat: fall back to comment match in case name is too long
e9aeecf xlate-test: use locally installed xlate tools
0ab58e3 xtables-compat: ebtables: handle mac masks properly
734ad40 xtables-compat: nft-arp: fix warning wrt. sprintf-out-of-bounds
fb7ae9f xtables-compat: truncate comments to 254 bytes
36976c4 extensions: libipt_DNAT: support shifted portmap ranges
d7ac61b iptables-test: add nft switch and test binaries from git
992e17d xtables-compat: only fetch revisions for ip/ip6
12a52ff xtables: Fix rules print/save after iptables update
1197c5e xtables: Register all match/target revisions supported by us and kernel
e3bb24c xtables: Check match/target size vs XT_ALIGN(size) at register time
3b2530c xtables: Do not register matches/targets with incompatible revision
d3f1437 xtables: Introduce and use common function to print val[/mask] arguments
29b1d97 xtables: Introduce and use common function to parse val[/mask] arguments
56aadc0 extensions: Initialize linear mapping of symbols in _init() of extension
79c2da9 extensions: ULOG: remove test
a0956ce ebtables-translate: turn off useless compat queries
9840869 nft: arptables: remove obsolete forward hook definition
7a37d14 iptables-compat: statify nft_restart()
a3aac1d iptables-compat: handle netlink dump EINTR errors
a567dc3 ebtables-compat: add 'vlan' match extension
7564bba ebtables-compat: add 'pkttype' match extension
4d40904 ebtables-translate: update table name on -t
5c8ce9c ebtables-compat: add 'ip6' match extension
8a85a14 libebt_ip: fix translations for tos and icmp
b6f0bec libebt_ip: add icmp support
f38ed1e xt-translate: quote interface names in translated output
71a6e37 icmp: split icmp type printing to header file
e67c088 ebtables-translate: add initial test cases
207dd5e xt-compat: add ebtables-translate
d988274 xlate-translate: split common parts into helper
1650806 xtables-eb: export 3 functions
6b2041c nft-bridge: add eb-translate backend functions
3063c37 nft-bridge: fix mac address printing
394a400 nft: fix crash when getprotobynumber() returns 0
6a1dbdf ebtables-compat: support intra-positioned negations
3e94f0a nft-bridge: add forward declaration for struct nftnl_rule
5024efe libebt_limit: print 'minute' and 'seconds', not 'min' and 'secs'
ce3c780 nft: make nft_init self-contained
cb151d5 xtables-translate: rm duplicate includes
69c089b xt-compat: constify a few struct members
03ecffe ebtables-compat: add initial translations
57af67d iptables: constify option struct
88231c4 ebtables-compat: load mark target
6b4e167 ebtables-compat: don't make failing extension load fatal
24110b5 libxt_comment: silence truncation warning
98fc8ce xtables-compat: only validate the xtables builtin tables
9d9b724 xtables-compat: skip unsupported tables
59d15cf xtables-compat: also validate priorities and hook points match expected values
eb35854 xtables-compat: fix snprintf truncation warnings
fc04c8a extensions: CLUSTERIP: do not allow --local-node 0
eb2c052 extensions: CLUSTERIP: add tests
ca3c397 iptables: add xtables-translate.8 manpage
5beb158 extensions: libxt_bpf: Fix build with old kernel versions
147a891 extenstions: ecn: add tcp ecn/cwr translation
ed928a8 extensions: add tests for comp match options
632ace7 xtables-compat-multi.c: Allow symlink of ebtables
d7ccc68 iptables: add xtables-compat.8 manpage
043da5b extensions: connmark: remove non-working translation
a93b502 extensions: prefer plain 'set' over 'set mark and'
577b7e2 xtables-compat-restore: use correct hook priorities
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
I wanted to add status LEDs support to my imx6 based board and have
found out, that I could use diag.sh script found in ramips platform,
which seems to be also shared in a few other platforms:
4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh
So I've extended the base diag.sh in a way, that if it detects any of
the DTS LED aliases, then it would use the generic DTS set_led_state
code.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz
1. Load Ramdisk via U-Boot
To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
* 115200bps
* 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.
U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm
2. Load image via GUI
a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.
3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin
Signed-off-by: Steven Lin <steven.lin@senao.com>
To be able to use the camera module, start_x=1 has to be set in
config.txt. This will cause the bootloader to load the GPU firmware that
contain the extra video codecs. Install these firmware files.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
An upstream change broke brcmfmac when loaded with modparam roamoff=1.
As we are carrying a patch that enables roamoff by default on the
brcm2708 target to improve stability, wireless is currently broken
there. Add a patch to fix brcmfmac with roamoff=1.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
For the parameters tls-cipher and ncp-ciphers more than one option can
be used in the OpenVPN configuration, separated by a colon, which should
be implemented as a list in order to configure it more clearly. By
adding the new OPENVPN_LIST option to the openvpn.options file with the
tls-cipher and ncp-cipher parameters, uci can now add this option as a
"list" and the init script will generate the appropriate OpenVPN
configuration from it.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This is actually a build dependency for /dev/crypto support in openssl.
Since it is a kernel module, it belongs here anyway.
- Removed Nikos Mavrogiannopoulos as maintainer.
- Streamlined make flags
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
This reverts commit 41770add03.
The fwtool_check_image() procedure is used by `sysupgrade --test` which must
not alter the image under test in any way.
Currently, when the LuCI ui or any other sysupgrade wrapper first invokes
sysupgrade --test to verify the compatibility of the image and then calculates
the sha256sum over it, the resulting checksum will differ from the original
image since the test invocation will implicitely strip the metadata trailer.
To properly fix the underlying issue, the combined image checksumming code
must be modified to skip the metadata trailer.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The return value of a package prerm script is discarded and not returned
correctly by default_prerm(). This allows other operations like service
shutdown to "leak" their return value, prompting workarounds like commit
48cfc826 which do not address the root cause.
Preserve a package prerm script return value for use by default_prerm(),
sharing the corresponding code from default_postinst() for consistency.
Also use consistent code for handling of /etc/init.d/ scripts.
Run Tested on: LEDE 17.01.4 running ar71xx.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update the OpenVPN package to version 2.4.6, refresh patches and drop
menuconfig options which are not supported upstream anymore.
Also fix the x509-alt-username configure flag - it is not supported
by mbedtls and was syntactically wrong in the Makefile - and the
port-share option which has been present in menuconfig but not been
used in the Makefile.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
dfa4ede interface: fix return code of __interface_add()
a82a8f6 netifd: fix resource leak on error in netifd_add_dynamic()
fa2403d config: fix resource leaks on error in config_parse_interface()
85de9de interface: fix memory leak on error in __interface_add()
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
As automatic helper assignment is disabled in recent Linux kernels,
explicit rules must be added to the raw table for each helper.
While commit f50a524 in the firewall3 project added a set of default
rules and other additional related functionality, both this and the
alternative manual methods of defining these rules require kmod-ipt-raw.
Signed-off-by: Steven Honson <steven@honson.id.au>
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.
Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM: 128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes
Hardware Highlights WNDAP660:
CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks
DRAM: 256 MB, 2 x 128 MiB DDR2
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE)
Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes
Flashing requirements:
- needs a tftp server at 192.168.1.10/serverip.
- special 8P8C(aka RJ45)<->D-SUB9 Console Cable
("Cisco Console Cable"). Note: Both WNDAP6x0 have
a MAX3232 transceivers, hence no need for any separate
CMOS/TTL level shifters.
External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
= Config# = | = GPIO 11 = | = GPIO 14 = | ===== Description =====
1. | 1 / High | 0 / Low | Use the internal antennae (default)
2. | 0 / Low | 1 / High | Use the external antennae
The external antennaes are only meant for the 2.4 GHz band.
One-way Flashing instructions via u-boot:
0. connect the serial cable to the RJ45 Console Port
Note: This requires a poper RS232 and not a TTL/USB adaptor.
1. power up the AP and interrupt the u-boot process at
'Hit any key to stop autoboot'
2. setup serverip and ipaddr env settings
Enter the following commands into the u-boot shell
# setenv ipaddr 192.168.1.1
# setenv serverip 192.168.1.10
3. download the factory.img image to the AP
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img
4. verfiy image integrity
Enter the following commands into the u-boot shell
# crc32 $fileaddr $filesize
If the calculated crc32 checksum does not match, go back to step 3.
5. flash the image
Enter the following commands into the u-boot shell
# nand erase 0x110000 0x1bd0000
# nand write ${kernel_addr_r} 0x110000 ${filesize}
6. setup uboot environment
Enter the following commands into the u-boot shell
# setenv bootargs
# setenv fileaddr
# setenv filesize
# setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0'
# setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}'
# setenv bootcmd 'run owrt_boot'
# saveenv
7. boot
# run bootcmd
Booting initramfs instructions via u-boot:
Follow steps 0 - 2 from above.
3. boot initramfs
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
# run addtty
# bootm ${kernel_addr_r}
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds u-boot environment access to the MX60(W) target.
"The environment size is one NAND block (128KiB on Buckminster).
We allocate four NAND blocks to deal with bad blocks which may
exist in the saved environment"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>