The Comtrend VG-8050 is a wifi gigabit ethernet router, 2.4 GHz single band with
two external antennas.
Hardware:
- SoC: Broadcom BCM63169
- CPU: dual core BMIPS4350 @ 400Mhz
- RAM: 128 MB DDR
- Flash: 128 MB NAND
- LAN switch: Broadcom BCM53125, 5x 1Gbit
- Wifi 2.4 GHz: SoC (BCM63268) 802.11bgn
- USB: 1x 2.0 (optional)
- Buttons: 2x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add an UCI option to enable Multiple BSSID Advertisement. Enabling this
will announce all BSSIDS on a phy in a single beacon frame. The
interface that is brought up first will be the transmitting profile, all
others are non-transmitting profiles and will be advertised in the
Multiple BSSID element in Beacon and Probe Response frames of the first
interface.
This depends on driver and client support. Enabling this will result in
all but the first interface not being visible at all for clients that do
not support it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
All switch ports are labeled as port@address so let's follow the same pattern.
Fixes: ed79519b8d ("bmips: add support for Netgear DGND3700 v1, DGND3800B")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Sercomm AD1018 is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB (v1) / 128 MB (v2) DDR
- Flash: 128 MB NAND
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM43217 802.11bgn
- USB: 1x 2.0
- Buttons: 3x (reset)
- LEDs: yes
- UART: yes
Installation via OEM web UI:
1. Use the admin credentials to login via web UI
2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
3. Press "Update Firmware" button and wait some minutes until it finish
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is needed on devices like Sercomm AD1018 for booting recent kernels due
to bigger kernels.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Maintaining bcm63xx is a nightmare due to the amount of devices and patches
required, since every board requires an individual patch due to the lack of
full device tree compatibility.
Moreover, there are a lot of devices supported on this target which won't work
due to not having enough resources (16M-32M of RAM and/or 4M of flash).
Therefore, any development efforts should be focused on bmips and support for
those devices with enough resources should be added on bmips target.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Actiontec R1000H is a gigabit wifi router, 2.4 GHz single band with
two external antennas. It comes with a coaxial HomePNA port.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 64 MB DDR
- Flash: 32 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- LAN coaxial : 1x HPNA 3.1, CG3211 + CG3213
- Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
- USB: 1x 2.0
- Buttons: 2x, 1 reset
- LEDs: 7x
- UART: yes
The HPNA hardware probably needs a firmware to make the coaxial port work.
In the OEM firmware, it's apparently sent with an utility (inhpna) through
the ethernet port.
Installation via CFE web UI:
1. Connect the UART serial port.
2. Power on the router and press enter at the console prompt to stop the
bootloader.
4. Browse to http://192.168.1.1 and upload the OpenWrt CFE firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Now that JFFS2 cleanmarkers are supported on the standard nand_do_upgrade
function we can start using it on bcm63xx.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Now that JFFS2 cleanmarkers are supported on the standard nand_do_upgrade
function we can start using it on bmips.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Some Broadcom MIPS devices require JFFS2 cleanmarkers to be present on the
kernel partition or the bootloader will identify the partition as corrupt and
won't boot the kernel.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The DGND3700v2 renames the cferam bootloader from cferam to cfeXXX, where XXX
is the number of firmware upgrades performed by the bootloader. Other bcm63xx
devices rename cferam.000 to cferam.XXX, but this device is special because
the cferam name isn't changed on the first firmware flashing but it's changed
on the subsequent ones.
Therefore, we need to look for "cfe" instead of "cferam" to properly detect
the cferam partition and fix the bootlop.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The DGND3700v2 renames the cferam bootloader from cferam to cfeXXX, where XXX
is the number of firmware upgrades performed by the bootloader. Other bcm63xx
devices rename cferam.000 to cferam.XXX, but this device is special because
the cferam name isn't changed on the first firmware flashing but it's changed
on the subsequent ones.
Therefore, we need to look for "cfe" instead of "cferam" to properly detect
the cferam partition and fix the bootlop.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Some devices rename cferam bootloader using specific patterns and don't follow
broadcom standards for renaming cferam files. This requires supporting
different cferam file names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
openssl sets additional cflags in its configuration script. We need to
make it aware of our custom cflags to avoid adding conflicting cflags.
Fixes: #12866
Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
Backport patches improving ppp interface creation. As a side effect this
also fix a bug from using netdev trigger that suffer from LED state
wrongly set due to using old ioctl for ppp creation.
Tested-by: Csaba Sipos <metro4@freemail.hu>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch initially introduced in 94b4da9b4a
breaks mvebu devices when using vlan filtering with kernel 5.15 or 6.1,
it was working ok in 5.10.
With this patch, frame that should exit untagged from the switch exit tagged.
Running 'tcpdump -Q out -evnnli eth1' (eth1 being the dsa interface)
- with the hack, frame is sent directly to the
destination port 4 with VID 2, so the switch leave the tag as instructed:
11:22:33:44:55:66 > 77:88:99:aa:bb:cc, Marvell EDSA ethertype 0xdada (Unknown), rsvd 0 0, mode From CPU, target dev 0, port 4, tagged, VID 2, FPri 0, ethertype ARP (0x0806), length 50: Ethernet (len 6), IPv4 (len 4), Request who-has 5.6.7.8 tell 1.2.3.4, length 28
- without the hack, frame is sent to the switch that
performs the forwarding decision and untagging:
11:22:33:44:55:66 > 77:88:99:aa:bb:cc, Marvell EDSA ethertype 0xdada (Unknown), rsvd 0 0, mode Forward, dev 1, port 0, tagged, VID 2, FPri 0, ethertype ARP (0x0806), length 50: Ethernet (len 6), IPv4 (len 4), Request who-has 5.6.7.8 tell 1.2.3.4, length 28
Removing this patch makes my Turris Omnia usable with vlan filtering,
ie wifi device can talk to wired device again.
Using kernel 5.15 some broadcast/multicast traffic is still leaked
(on a VLAN 2 access port I see tagged VLAN 3 frame),
using kernel 6.1 fixes that.
People needing the extra performance should try the bridger package.
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
The Comtrend AR-5381u is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB DDR
- Flash: 16 MB SPI NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM43225 802.11bgn
- USB: 1x 2.0
- Buttons: 1x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This was done by executing these commands:
$ ./scripts/kconfig.pl '+' target/linux/generic/config-6.1 /dev/null > target/linux/generic/config-6.1-new
$ mv target/linux/generic/config-6.1-new target/linux/generic/config-6.1
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This ports the TP-Link TL-WDR6500 v2 from ar71xx to ath79.
Specifications:
SoC: QCA9561
CPU: 750 MHz
Flash: 8 MiB (Winbond W25Q64FVSIG)
RAM: 128 MiB
WiFi 2.4 GHz: QCA956X 3x3 MIMO 802.11b/g/n
WiFi 5 GHz: QCA9882-BR4A 2x2 MIMO 802.11a/n/ac
Ethernet: 4x LAN and 1x WAN (all 100M)
USB: 1x Header
Flashing instructions:
As it appears, the device does not support flashing via GUI or
TFTP, only serial is possible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Xiaobing Luo <luoxiaobing0926@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the repository
link to the new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the repository
link to the new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the link reference to the
new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The Comtrend WAP-5813n is a wifi gigabit router, 2.4 GHz single band with
two external antennas.
Hardware:
- SoC: Broadcom BCM6369
- CPU: dual core BMIPS4350 @ 400Mhz
- RAM: 64 MB DDR
- Flash: 8 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM4322 802.11bgn
- USB: 1x 2.0 (optional)
- Buttons: 3x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
If dual-stack configuration is in use, and dhcpv6 option is set, do not start
464xlat sub-interface for dhcpv6 sub-interace , as the configuration already
provides IPv4 connectivty, be it through single or dual APN configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add two new "v6apn" and "v6profile" properties, to support split-APN
dual-stack onfiguration. This extends the existing ipv4v6 PDP type,
allowing simultaneous connection to two distinct APNs,
one for IPv4 and one for IPv6.
The parameters override existing 'apn' and 'profile' respectively,
if set, but only for IPv6 part of the connection.
If unset, they default to their original values, constituting a standard
IPv4v6 setup.
If a different APN is set for IPv6, a corresponding profile MUST also be
configured, with a different ID, than the IPv4 profile, for example,
profile 2.
Both APNs must match ones configured through QMI or through 'AT+CGDCONT'
command.
Example configuration in UCI:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option autoconnect '1'
option pdptype 'ipv4v6'
option apn 'internet'
option v6apn 'internetipv6'
option profile '1'
option v6profile '2'
Corresponding profile configuration:
AT+CGDCONT?
+CGDCONT: 1,"IP","internet","0.0.0.0",0,0,0,0
+CGDCONT: 2,"IPV6","internetipv6","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
move wan port to gmac1 to achieve 2Gbps CPU bandwidth between wan and
lan on YunCore FAP-640
Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
RISC-V has no support for subword atomic operations; code currently
generates libatomic library calls.
This patch changes the default behavior to fast inline subword atomic
calls that do not require libatomic.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The Comtrend VR-3025un is a wifi gigabit router, 2.4 GHz single band with
two external antennas.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 @ 400Mhz
- RAM: 64 MB DDR
- Flash: 8 MB parallel NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM43222 802.11bgn
- USB: 1x 2.0
- Buttons: 1x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the antenna.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The cli is a one-time run, and memory leaks would have been irrelevant. But people call libsw with cli programs as samples.
Doing a good job of memory management calls means that people who call libsw are not so easy to make mistakes.
Signed-off-by: nichel Chen <nichelnich@gmail.com>
Align all the device tree files and follow the same criteria before more
devices are ported from bcm63xx and this goes out of control.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Netgear EVG2000 is a wifi gigabit router, 2.4 GHz single band with
two internal antennas integrated in the main PCB.
Hardware:
- SoC: Broadcom BCM6369
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 64 MB DDR
- Flash: 16 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
- USB: 2x 2.0
- Buttons: 2x, 1 reset
- LEDs: 10x
- FXS: 2x
- UART: yes
Installation via CFE web UI:
1. Power off the router and make a temporal TX-RX shortcircuit on the
serial pins.
2. Power on the router and wait 3 or more seconds
3. Remove the TX-RX shortcircuit
4. Browse to http://192.168.1.1 or http://192.168.0.1 and upload the
firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.
Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation (fw 2.0.9)
-----------------------
1. Login to the web interface under SuperUser (root) credentials.
Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
device written on the backplate stick.
2. Navigate to Setting -> WAN. Add:
Name - WAN1
Connection Type - Static
IP Address - 172.16.0.1
Netmask - 255.255.255.0
Save -> Apply. Set default: WAN1
3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
Protocol - SSH
Port - 22
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN Interface - WAN1
Save ->Apply
Add:
Protocol - HTTP
Port - 80
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN interface - WAN1
Save -> Apply
4. Set up your PC ethernet:
Connection Type - Static
IP Address - 172.16.0.2
Netmask - 255.255.255.0
Gateway - 172.16.0.1
5. Connect PC using ethernet cable to the WAN port of the router
6. Connect to the router using SSH shell under SuperUser account
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 171.16.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:e8 |
| WAN | label + 1 | *:e9 |
| 2g | label + 4 | *:ec |
| 5g | label + 5 | *:ed |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset | Size | Description |
+---+-------------------+-------------+--------------------+
| 1 | 0x0 | 0x200 | Tag Header Factory |
| 2 | 0x200 | 0x100 | Tag Header Kernel1 |
| 3 | 0x300 | 0x100 | Tag Header Kernel2 |
| 4 | 0x400 | SIZE_KERNEL | Kernel |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) |
+---+-------------------+-------------+--------------------+
Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
This improves compatibility with the elder stock firmwares of the
following devices, which have not yet been merged into OpenWrt:
- Beeline SmartBox Pro
- Beeline SmartBox Turbo+
- WiFire S1500.NBN
Without this, OpenWrt factory image installation may fail.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
Make it possible to easily customize U-Boot config options via new
`UBOOT_CUSTOMIZE_CONFIG` variable, so we don't need to patch config
files or override config step with shell hackery.
This generic approach uses `config` CLI to tweak the .config as needed,
for example:
UBOOT_CUSTOMIZE_CONFIG := \
--enable CMD_EFIDEBUG \
--enable CMD_BOOTMENU \
--enable AUTOBOOT \
--enable AUTOBOOT_MENU_SHOW \
--disable AUTOBOOT_KEYED \
--disable AUTOBOOT_USE_MENUKEY \
--disable BOOTMENU_DISABLE_UBOOT_CONSOLE \
--set-val BOOTDELAY 2
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The armvirt target has been renamed to 'armsr' (Arm SystemReady)
after inclusion of EFI support.
Change references (including subtargets) accordingly.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The armvirt target has been renamed to armsr (Arm SystemReady),
so the GRUB configuration also needs to change.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
armvirt target has been renamed to armsr (Arm SystemReady),
so the config defaults need to be changed as well.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
