bootfs still needs more work before it's ready.
For some unknown reason model RAXE500 uses board id RAX220.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 63ba3eaccd)
It's needed to support devices with U-Boot. That bootloader passes MTD
layout using cmdline.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 21d28adbc1)
It still isn't ready though - more data needs to be added to the bootfs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 494c033f9c)
New BCM4908 family based routers will use U-Boot bootloader. That will
require using a totally different firmware format. Kernel has to be put
in a FIT image.
OpenWrt has some helpers for generating .its files but they don't fit
BCM4908 requirements and there is no simple way of extending any of
them. The best solution seems to be storing an .its template.
BCM4908 bootfs may:
1. contain extra binaries (other than kernel & DTB)
2. include multiple DTB files
3. store device specific U-Boot configurations with custom properties
Such setups are too complex to generate using shell script. Raw .its
file on the other hand seems quire clean & reasonable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a02c971dff)
This simplifies some operations as it doesn't have to be caculated over
and over. It will also allow adding support for more vendor formats.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 063038bcef)
List of supported formats grew over time and implementation got a bit
messy. There are multiple functions with format-specific parameters and
commands.
Refactor it by making platform_identify() setup all required info right
after detecting firmware format. This simplifies formats handling in
platform_other_check_image() and platform_do_upgrade() a lot.
This has been tested on:
1. SmartRG SR400ac (TRX): non-NAND sysupgrade
2. Netgear R8000 (CHK): NAND aware and standard sysupgrade-s
3. D-Link DIR-885L (Seama): NAND aware and standard sysupgrade-s
4. Luxul XWR-3150 (LXL): NAND aware and standard sysupgrade-s
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 80041dea70)
Both should be supported since:
1. Adding NVMEM driver for NVRAM
2. Using NVRAM info for determining active firmware partition
Linksys EA9500 uses very similar design and works fine.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 287257d676)
This includes:
1. BCM5301X changes from 5.14 and queued 5.15 stuff
2. NSP changes from 5.11 - 5.15 for kernel 5.10
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit bce00f47e5)
Port numbers were reverted.
Fixes: c459a6bf48 ("bcm53xx: add support for Luxul FullMAC WiFi devices")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 53546c3e94)
Removed upstreamed:
target/linux/mvebu/patches-5.4/001-PCI-aardvark-Wait-for-endpoint-to-be-ready-before-tr.patch
target/linux/mvebu/patches-5.4/016-PCI-aardvark-Train-link-immediately-after-enabling-t.patch
target/linux/mvebu/patches-5.4/017-PCI-aardvark-Improve-link-training.patch
target/linux/mvebu/patches-5.4/018-PCI-aardvark-Issue-PERST-via-GPIO.patch
target/linux/mvebu/patches-5.4/020-arm64-dts-marvell-armada-37xx-Set-pcie_reset_pin-to-.patch
The following patch does not apply to upstream any more and needs some
more work to make it work fully again. I am not sure if we are still
able to set the UART to a none standard baud rate.
target/linux/ath79/patches-5.4/921-serial-core-add-support-for-boot-console-with-arbitr.patch
These patches needed manually changes:
target/linux/generic/pending-5.4/110-ehci_hcd_ignore_oc.patch
target/linux/ipq806x/patches-5.4/0065-arm-override-compiler-flags.patch
target/linux/layerscape/patches-5.4/804-crypto-0016-MLKU-114-1-crypto-caam-reduce-page-0-regs-access-to-.patch
target/linux/mvebu/patches-5.4/019-PCI-aardvark-Add-PHY-support.patch
target/linux/octeontx/patches-5.4/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch
All others updated automatically.
Compile-tested on: malta/le, armvirt/64, lantiq/xrx200
Runtime-tested on: malta/le, armvirt/64, lantiq/xrx200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Device specifications
* SoC: QCA9563 @ 775MHz (MIPS 74Kc)
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (EN25QH128)
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9988): a/n/ac, 4x4 MU-MIMO
* IoT Wireless 2.4GHz (QCA6006): currently unusable
* Ethernet (AR8327): 3 LAN × 1GbE, 1 WAN × 1GbE
* LEDs: Internet (blue/orange), System (blue/orange)
* Buttons: Reset
* UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
* Power: 12VDC, 1,5A
MAC addresses map (like in OEM firmware)
art@0x0 88:C3:97:*:57 wan/label
art@0x1002 88:C3:97:*:2D lan/wlan2g
art@0x5006 88:C3:97:*:2C wlan5g
Obtain SSH Access
1. Download and flash the firmware version 1.3.8 (China).
2. Login to the router web interface and get the value of `stok=` from the
URL
3. Open a new tab and go to the following URL (replace <STOK> with the stok
value gained above; line breaks are only for easier handling, please put
together all four lines into a single URL without any spaces):
http://192.168.31.1/cgi-bin/luci/;stok=<STOK>/api/misystem/set_config_iotdev
?bssid=any&user_id=any&ssid=-h%0Anvram%20set%20ssh_en%3D1%0Anvram%20commit
%0Ased%20-i%20%27s%2Fchannel%3D.%2A%2Fchannel%3D%5C%5C%22debug%5C%5C%22%2F
g%27%20%2Fetc%2Finit.d%2Fdropbear%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A
4. Wait 30-60 seconds (this is the time required to generate keys for the
SSH server on the router).
Create Full Backup
1. Obtain SSH Access.
2. Create backup of all flash (on router):
dd if=/dev/mtd0 of=/tmp/ALL.backup
3. Copy backup to PC (on PC):
scp root@192.168.31.1:/tmp/ALL.backup ./
Tip: backup of the original firmware, taken three times, increases the
chances of recovery :)
Calculate The Password
* Locally using shell (replace "12345/E0QM98765" with your router's serial
number):
On Linux
printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" | \
md5sum - | head -c8 && echo
On macOS
printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" | \
md5 | head -c8
* Locally using python script (replace "12345/E0QM98765" with your
router's serial number):
wget https://raw.githubusercontent.com/eisaev/ax3600-files/master/scripts/calc_passwd.py
python3.7 -c 'from calc_passwd import calc_passwd; print(calc_passwd("12345/E0QM98765"))'
* Online
https://www.oxygen7.cn/miwifi/
Debricking (lite)
If you have a healthy bootloader, you can use recovery via TFTP using
programs like TinyPXE on Windows or dnsmasq on Linux. To switch the router
to TFTP recovery mode, hold down the reset button, connect the power
supply, and release the button after about 10 seconds. The router must be
connected directly to the PC via the LAN port.
Debricking
You will need a full dump of your flash, a CH341 programmer, and a clip
for in-circuit programming.
Install OpenWRT
1. Obtain SSH Access.
2. Create script (on router):
echo '#!/bin/sh' > /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
echo '. /bin/boardupgrade.sh' >> /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
echo 'board_prepare_upgrade' >> /tmp/flash_fw.sh
echo 'mtd erase rootfs_data' >> /tmp/flash_fw.sh
echo 'mtd write /tmp/openwrt.bin firmware' >> /tmp/flash_fw.sh
echo 'sleep 3' >> /tmp/flash_fw.sh
echo 'reboot' >> /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
chmod +x /tmp/flash_fw.sh
3. Copy `openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin`
to the router (on PC):
scp openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin \
root@192.168.31.1:/tmp/openwrt.bin
4. Flash OpenWRT (on router):
/bin/ash /tmp/flash_fw.sh &
5. SSH connection will be interrupted - this is normal.
6. Wait for the indicator to turn blue.
Signed-off-by: Evgeniy Isaev <isaev.evgeniy@gmail.com>
[improve commit message formatting slightly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6c148116f7)
Currently it is not possible to configure VLANs via LUCI on
tplink tl-mr3020-v3. This patch fixes switch topology for the
LUCI interface.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
[copied commit message from github PR]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit e22c91e144)
Update busybox to 1.33.2, which includes only 5 commits after 1.33.1
Bug fix release. 1.33.2 has fixes for hush and ash (parsing fixes)
and unlzma (fix where we could read before beginning of buffer).
https://git.busybox.net/busybox/log/?h=1_33_2
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
71e08471ab56 mt76: eeprom: fix return code on corrected bit-flips
9a8fc6636d83 mt76: move sar_capa configuration in common code
7cdbea1dc82a mt76: only access ieee80211_hdr after mt76_insert_ccmp_hdr
678071ef7029 mt76: mt7615: clear mcu error interrupt status on mt7663
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit fc4398fe71)
a6451fea5a3d mt76: mt7615: improve wmm index allocation
1911486414dc mt76: mt7915: improve wmm index allocation
7998a41d1321 mt76: clear sta powersave flag after notifying driver
664475574438 mt76: mt7603: introduce SAR support
5c0da39c940b mt76: mt7915: introduce SAR support
77fc6c439a32 mt76: mt7603: improve reliability of tx powersave filtering
094b3d800835 firmware: update mt7663 rebb firmware to 20200904171623
25237b19bcc1 mt76: eeprom: tolerate corrected bit-flips
1463cb4c6ac2 mt76: mt7921: fix boolreturn.cocci warning
586bad6020f7 mt76: mt7921: use correct iftype data on 6GHz cap init
8ec95c910425 mt76: mt7921s: fix bus hang with wrong privilege
688e30c7d854 firmware: update mt7921 firmware to version 20211014
6fad970893dd mt76: fix key pointer overwrite in mt7921s_write_txwi/mt7663_usb_sdio_write_txwi
95acf972750c mt76: fix 802.3 RX fail by hdr_trans
3f402b0cf6c0 mt76: mt7921s: fix possible kernel crash due to invalid Rx count
929a03a8d65d mt76: connac: fix last_chan configuration in mt76_connac_mcu_rate_txpower_band
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 7e15390056)
Follow up to commit c744798cad. Managed to
hit the very same issue again while playing with the NOR SPL builds.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The board has a fixed size kernel partition but do not limit the kernel
size during image building.
Disable image building for both boards as well, since the kernel of the
last release as well as master are to big to fit into the 2 MByte kernel
partition.
Signed-off-by: Mathias Kresin <dev@kresin.me>
If authentication fails repeatedly e.g. because of a weak signal, the link
can end up in blocked state. If one of the nodes tries to establish a link
again before it is unblocked on the other side, it will block the link to
that other side. The same happens on the other side when it unblocks the
link. In that scenario, the link never recovers on its own.
To fix this, allow restarting authentication even if the link is in blocked
state, but don't initiate the attempt until the blocked period is over.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit f84053af5c)
Some drivers that do their own sequence number allocation (e.g. ath9k, mwlwifi) rely
on being able to modify params->ssn on starting tx ampdu sessions.
This was broken by a change that modified it to use sta->tid_seq[tid] instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit ddd977fcc5)
When a ubus event handler denies a association with a non-zero return
value, the code jumps to preceeding code, creating an endless loop until
the event handler accepts the assc request.
Move the ubus handler further up the code to avoid creating such a loop.
Signed-off-by: David Bauer <mail@david-bauer.net>
They can be added as hex digit strings via the 'vendor_elements' option
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 1818b038d7)
This makes it possible to avoid using a RADIUS server for WPA enterprise authentication
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from 98621c9782)
This allows WPA enterprise roaming in the same mobility domain without any
manual key configuration (aside from radius credentials)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 704ab6a002)
Using a pointer one lifter after it freed is not the best idea.
Let's not do that.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry-picked from commit 63c01ad025)
This implements the mapping recommendations from RFC8325, with an
update from RFC8622. This ensures that DSCP marked packets are properly
sorted into WMM classes.
The map can be disabled by setting iw_qos_map_set to something invalid
like 'none'
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit a5e3def182)
This feature is useful on its own even without full interworking support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit efff3520f4)
Both hostapd and netifd attempt to add a VLAN device to a bridge.
Depending on which one wins the race, bridge vlan settings might be incomplete,
or hostapd might run into an error and refuse to service the client.
Fix this by preventing hostapd from adding interfaces to the bridge and
instead rely entirely on netifd handling this properly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit da4be02fcd)
(cherry-picked from commit 63c01ad025)
When using htmode 'HE20' with a radio mode that uses wpa-supplicant
(like mesh or sta), it will default to 40 MHz bw if disable_ht40 is not
set. This commit fixes this behaviour.
Signed-off-by: Jesus Fernandez Manzano <jesus.manzano@galgus.net>
(cherry-picked from commit af83e3ce0f)
