Commit Graph

22048 Commits

Author SHA1 Message Date
Manuel Kock
509894cffb lantiq: remove redundant WiFi LED on FRITZ!Box 7320
The led wireless trigger is already set correctly to phy0tpt through the
alias in the device tree.

Signed-off-by: Manuel Kock <github.web@manu.li>
[rephrased commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-11 18:17:29 +01:00
Paul Spooren
e97113d5e1 x86,tegra,mvebu: image: use common reproducible IMG_PART_SIGNATURE
These targets are currently using more or less same SIGNATURE variable
which provides unique partition ID/signature, so it makes sense to
refactor it out into common IMG_PART_SIGNATURE variable which could be
reused by all targets.

This is another step in the direction of reproducible OpenWrt images.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[split into separate commit, renamed to IMG_PART_SIGNATURE]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-11 16:37:13 +01:00
Adrian Schmutzler
1c321237c2 ramips: split further base-files across subtargets
As started in 19724e28c8 ("ramips: split base-files into
subtargets"), this moves some smaller left-over files to the
appropriate base-files folder of their subtarget:

- /etc/init.d/bootcount
- /etc/uci-defaults/04_led_migration

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-11 14:53:06 +01:00
Adrian Schmutzler
5dc535419f ath79: fix identifier for Nanostation M in ath9k caldata extraction
When Nanostation M was renamed from ubnt,nano-m to ubnt,nanostation-m
in commit f1396ac753 ("ath79: align naming of Ubiquiti Nanostation M"),
the caldata extraction in 10-ath9k-eeprom was overlooked.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-11 00:33:34 +01:00
David Bauer
b16d76bf40 ramips: correct Netgear WNDR3700v5 button flag
This adjusts the GPIO state flag to ACTIVE_LOW as FCC pictures indicate
the base board is identical to the one of the R6220.

Fixes commit 3459013257 ("ramips: correct R6220 button flag")

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-10 20:57:16 +01:00
David Bauer
3459013257 ramips: correct R6220 button flag
All buttons on the Netgear R6220 are active-low while they are flagged
as active-high.

The GPIO status reads the following for no buttons pressed:

root@64367-r6220:~# cat /sys/kernel/debug/gpio
gpio-7   (                    |wps                 ) in  hi
gpio-8   (                    |wifi                ) in  hi
gpio-14  (                    |reset               ) in  hi

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-09 19:15:40 +01:00
Álvaro Fernández Rojas
f586dd67ac brcm63xx: add linux 4.19 support
Boot tested on Comtrend AR-5387un:
https://gist.github.com/Noltari/57e5030455da8dc38e61f8c3a5922254

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jonas.gorski: make 4.19 an optional testing version; add gcc 8.3 fix]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2019-11-09 13:16:01 +01:00
Michael Heimpold
9673d5c7ab mxs: start a console on USB gadget serial ports
The I2SE Duckbill devices are pen-drive like and thus the usage
of the USB gadget subsystem is highly indicated.

Spawning a console if a serial gadget is configured saves
us from connecting a physical debug uart.

On Olimex OLinuXino Maxi/Mini boards, this does not hurt.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2019-11-09 12:56:34 +01:00
Michael Heimpold
9a5fd2fa85 mxs: switch to askconsole
Remove the dedicated tty name and use askconsole to spawn the console
on serial debug uart.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2019-11-09 12:56:32 +01:00
Michael Heimpold
002e312538 mxs: add support and switch to kernel 4.19
Also remove kernel 4.14 support and the meanwhile obsolete patch.

This was run-tested on I2SE Duckbill device and
Olimex OLinuXino Maxi board.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Tested-by: Zoltan HERPAI <wigyori@uid0.hu>
2019-11-09 12:56:28 +01:00
Adrian Schmutzler
f098c612b6 ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3
This moves shared code of the named devices into a common DTSI.

Remove setting status="okay" for &gpio0 as it's not disabled in
mt7620a.dtsi.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:17:31 +01:00
Frederik Noe-Sdun
4a904b8b76 ramips: increase max SPI frequency to 50 MHz for EX3700/EX6130
Based on Macronix MX25L3205DM2I datasheet this is maximum
supported speed.

Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, improved commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:17:25 +01:00
Frederik Noe-Sdun
0cbd2c74d0 ramips: add support for Netgear EX6130
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The -factory images can be flashed from the
device's web interface or via nmrpflash.

The device seems to use base PCB as EX3700/EX3800,
but supporting AC1200 using MT7612E.

MAC adresses:
5.0 GHz  0x8004  *:9a
2.4 GHz  0x4     *:9b
lan      0x28    *:9b
wan      0x2e    *:9c

Since this is a one-port device, although wan MAC address is
set in flash, it is not used in OpenWrt setup.

Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, extended commit message, tiny DTS style fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:16:14 +01:00
南浦月
0ff2385a92 ar71xx: fix tl-wdr3320-v2 upgrade
Fix the error that tl-wdr3320-v2 can't upgrade firmware via web
interface by using magic_ver="0200" for this device.

Signed-off-by: 南浦月 <nanpuyue@gmail.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 16:29:01 +01:00
Kristian Evensen
6ab84579c6 ipq40xx: u4019: use reset-gpios instead of phy-reset-gpio
Use reset-gpio instead of the custom phy-reset-gpio property to do phy
reset on the U4019. phy-reset-gpio was incorrectly introduced when we
added support for the U4019, and will be deprecated.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-11-07 22:51:37 +01:00
Daniel Danzberger
8db4496443 ipq40xx: wpj419: use reset-gpios property for phy reset
The old GPIO based phy reset (phy-reset-gpio) will be removed form
the ipq40xx mdio driver in the future.

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
2019-11-07 22:51:37 +01:00
DENG Qingfang
6abce4d5e4 ipq40xx: mdio: remove support for phy-reset-gpio
Commit 6f6c00cfc9 ("ipq40xx: Add support for Unielec U4019") has
introduced support for `phy-reset-gpio` DT property, which isn't needed
as the MDIO already supports `reset-gpios`[1] which could be used instead.

1. https://elixir.bootlin.com/linux/v4.19.81/source/Documentation/devicetree/bindings/net/mdio.txt

Ref: PR#2511
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[commit title and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-07 22:51:37 +01:00
Adrian Schmutzler
a921945773 ramips: rename keys node formerly named button
For some devices, the keys node is named "button". Change name to
match the rest of the target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-07 17:13:18 +01:00
Adrian Schmutzler
4176100b06 ath79: replace generic button node names
In several DTS files, button nodes are just named buttonX or
xxx_button. This replaces the names with more specific names matching
the majority of key definitions.

While at it, fix name of keys node in one case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-07 17:13:18 +01:00
Martin Schiller
edbadec843 kernel: fix LED netdev trigger on interface rename
This fixes the netdev LED trigger for interfaces, which are renamed
during initialization (e.g. ppp interfaces).

Fixes: FS#2193
Fixes: FS#2239
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-11-07 00:10:18 +01:00
Paul Spooren
9fa061a7d3 ramips, mt7620: reproducible elecom-header uid/gid
The elecom-header renames the firmware image to v_0.0.0.bin, stores its
MD5 sum as v_0.0.0.md5 and tars both files again.

Both v_0.0.0 files are created as the build user making it harder to
reproduce.

This commit sets the owner/group of both files to root by adding extra
options to the final tar command.

Before:
0 buildbot   (101) buildbot   (102)  3932164 2019-11-05 14:43:22.000000 v_0.0.0.bin
0 buildbot   (101) buildbot   (102)       33 2019-11-05 14:43:22.000000 v_0.0.0.md5

After:
0 root         (0) root         (0)  3932164 2019-11-05 23:43:08.000000 v_0.0.0.bin
0 root         (0) root         (0)       33 2019-11-05 23:43:08.000000 v_0.0.0.md5

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-11-06 23:23:52 +01:00
Adrian Schmutzler
c8c4f7216e ath79: specify N and ND subversions of TL-WR941 with ALT0_MODEL
TP-Link's TL-WR941 is sold with detachable antennas
internationally (ND version), but with fixed antennas in China
(N version). While hardware and images are similar for both
variants of v2 and v4, they are different for v6.

Having both explicitly will make it easier for user to identify
the correct image, and most importantly will raise awareness
that N and ND are not necessarily always the same as for
TL-WR841 series.

With an image selection webpage, using ALT0_MODEL as in this
patch will provide the option to list versions for N and ND
separately.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 15:04:05 +01:00
Adrian Schmutzler
c7842ceaaa ramips: reorganize DTSI files for Netgear R devices
This reorganizes DTSI files for the Netgear R devices in mt7621
(and the WNDR3700 v5). It creates a common DTSI for all R (sercomm)
devices and distributes the remaining code in r6220.dtsi to R6220
and WNDR3700 v5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 14:43:04 +01:00
Sungbo Eo
62b1559b56 ramips: improve support for WeVO 11AC NAS and W2914NS v2
- remove WAN port index
- load WAN MAC address directly from the flash
- provide label MAC address
- increase flash's SPI frequency to 80MHz
- add mt76 led nodes to make WiFi LEDs work
- drop unnecessary pinmux groups

The factory partition scheme for MAC addresses (verified on both devices):
0x4   : WiFi 2.4GHz (label_mac-9)
0x28  : unused
0x2e  : WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-5)
0xe000: LAN (label_mac-1)
0xe006: unused

By improving flash speed,
`time dd if=/dev/mtdblock3 of=/dev/null bs=64k`
has been reduced from 14.51s to 3.11s.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebased]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 14:31:32 +01:00
Adrian Schmutzler
15dc60e727 ath79: move eth0 to parent DTSI for ar9344 TP-Link CPE devices
The &eth0 node is the same for all TP-Link CPE devices in ar9344,
so move it to parent DTSI. While at it, do some minor DTS
harmonizations.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:51:20 +01:00
Andrew Cameron
bae0d47f2e ath79: add support for the TP-LINK CPE220 V3
This adds support for a popular low-cost 2.4GHz N based AP

Specifications:
SoC: Qualcomm Atheros QCA9533 (650MHz)
RAM: 64MB
Storage: 8 MB SPI NOR
Wireless: 2.4GHz N based built into SoC 2x2
Ethernet: 2x 100/10 Mbps, integrated into SoC

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

This also applies some minor changes to the common DTSI:
- use &wmac for label-mac-device, as this one is actually set up in
  common DTSI
- move &eth0 to parent DTSI
- fix several leading spaces, added/removed newlines

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[DTS style fixes/improvements, updated commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:37:40 +01:00
Adrian Schmutzler
d2b9333ea9 ramips: remove default case for MAC address assignment
So far, MAC address assignment in ramips has contained a default
case, which defined wan_mac = eth0 + 1 for _every_ device not
having an explicit case there.

This is not desirable, as many device supporters will just not
care or know about this definition, so another MAC address will be
introduced by accident. In some cases the wan_mac is assigned
although it is not needed, in other cases even addresses not
dedicated to the device will be used (e.g. wan_mac actually is
eth0 - 1, but during support nobody cared, so eth0 + 1 is used now,
which might actually belong to another device ...).

Thus, in this PR the former default case is converted to an
explicit case. This one comprises all devices not being accounted
for by other cases, reduced by those not having wan at all.
The big number of entries for this node might be another indication
that many of them wouldn't actually be there if there hadn't been
default wan_mac setup.

In exchange, the current "do nothing" case can be removed, as it
will be the new default case.

The devices being put in the newly created explicit case were
determined as follows:

1. Create a list of all devices based on the DTS files.

2. Remove all devices already having an explicit entry setting
   their address.

3. Remove all devices that only have lan set up in the first part
   of 02_network:

mt7620:
   - alfa-network,tube-e4g
   - asus,rp-n53
   - buffalo,wmr-300
   - comfast,cf-wr800n
   - edimax,ew-7476rpc
   - edimax,ew-7478ac
   - elecom,wrh-300cr
   - hnet,c108
   - kimax,u25awf-h1
   - kimax,u35wf
   - kingston,mlw221
   - kingston,mlwg2
   - microduino,microwrt
   - netgear,ex2700
   - netgear,ex3700
   - netgear,wn3000rp-v3
   - planex,cs-qr10
   - planex,mzk-ex300np
   - planex,mzk-ex750np
   - ravpower,wd03
   - sercomm,na930
   - yukai,bocco
   - zbtlink,zbt-cpe102
   - zte,q7

mt7621:
   - gnubee,gb-pc1
   - gnubee,gb-pc2
   - linksys,re6500
   - mikrotik,rbm11g
   - netgear,ex6150
   - thunder,timecloud
   - tplink,re350-v1
   - tplink,re650-v1

mt76x8:
   - alfa-network,awusfree1
   - d-team,pbr-d1
   - glinet,vixmini
   - vocore,vocore2-lite
   - tama,w06
   - tplink,tl-mr3020-v3
   - tplink,tl-wa801nd-v5
   - tplink,tl-wr802n-v4
   - tplink,tl-wr902ac-v3
   - vocore,vocore2
   - widora,neo-16m
   - widora,neo-32m

rt288x:
   - buffalo,wli-tx4-ag300n
   - dlink,dap-1522-a1

rt305x:
   - allnet,all0256n-4m
   - allnet,all0256n-8m
   - allnet,all5002
   - allnet,all5003
   - alphanetworks,asl26555-16m
   - alphanetworks,asl26555-8m
   - asus,wl-330n
   - aximcom,mr-102n
   - dlink,dcs-930
   - easyacc,wizard-8800
   - hame,mpr-a2
   - hootoo,ht-tm02
   - huawei,d105
   - intenso,memory2move
   - planex,mzk-dp150n
   - rt305x dlink,dcs-930l-b1
   - sparklan,wcr-150gn
   - tenda,3g150b
   - tenda,3g300m
   - tenda,w150m
   - trendnet,tew-638apb-v2
   - unbranded,a5-v11
   - vocore,vocore-16m
   - vocore,vocore-8m
   - wansview,ncs601w
   - zorlik,zl5900v2

rt3883:
   - loewe,wmdr-143n
   - omnima,hpm

4. Put the remaining devices in the new case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:17:25 +01:00
Adrian Schmutzler
f4026ad24d ath79: DTS file style update and harmonization
This applies several style adjustments that have been requested in
recent reviews to older DTS files. Despite making the code base more
consistent, this will also help to reduce review time when DTSes
are copy/pasted.

Applied changes:
- Rename gpio-keys/gpio-leds to keys/leds
- Remove node labels that are not used
- Use label property for partitions
- Prefix led node labels with "led_"
- Remove redundant includes
- Harmonize new lines after status property
- Several smaller style fixes

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 00:27:55 +01:00
Sungbo Eo
763914ef1b ramips: improve netis WF-2881 support
This patch does the following:

1. remove u-boot-env partition
   Stock bootloader saves env variables at 0x80000 in flash,
   and there is nothing stored at 0x30000.
   By merging the partition "u-boot-env" with "u-boot",
   the partition table becomes the same as used in stock firmware:
   00000000-00080000: "Bootloader"
   00080000-00100000: "Config"
   00100000-00140000: "Factory"
   00140000-07f80000: "Kernel"

2. fix LAN/WAN MAC addresses and provide label MAC address
   Ethernet MAC addresses are stored in factory partition at:
   0xe000: LAN (label_mac)
   0xe006: WAN (label_mac+1)

3. fix LAN port order
   WF-2881 LAN ports are in reverse order of switch ports.

4. fix WiFi LEDs
   mt76 led nodes are added to make WiFi LEDs work.
   On top of this, mt76 node names are changed to more generic ones,
   and compatible strings are also added.

5. fix pinmux groups
   uart3 and uart2 pins are used as button and led, but jtag pins are not.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-06 00:27:55 +01:00
Petr Štetiar
04d6753d03 Revert "ipq806x: fix EA8500 switch control"
There is a problem with the EA8500, the switch will not work after soft
reboot, the only way to get it working again is to power cycle it
manually.

There are probably several issues in the play, it's quite hard to fix it
without having access to the actual device, so I don't see any other
option now, then revert the offending commit.

Ref: PR#2047
Fixes: FS#2168 ("Switch no longer work after restart on Linksys EA8500")
Reported-by: Adam <424778940z@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-06 00:21:15 +01:00
Adrian Schmutzler
443ba75c4e ath79: fix sorting and harmonize indent in tiny board.d files
This seems to have been overlooked when splitting base files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-05 13:14:29 +01:00
David Bauer
70d5989c9c ipq806x: use switch trigger for WAN LED on NETGEAR boards
With this commit, the WAN LED is triggered by the switch port state
instead of the eth0 netdev.
Otherwise, the LED is always illuminated, regardless of the WAN port
link state.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-04 18:50:53 +01:00
Sungbo Eo
6ea5f7d44c ramips: fix MTK_SOC for RT3662 devices
rt3883.mk contains both RT3662 and RT3883 device profiles, but commit
6a104ac772 set MTK_SOC to rt3883 for all devices. This patch fixes it,
and renames dts files accordingly. And SoC compatible strings are also
appended in the dts.

Fixes: 6a104ac772 ("ramips/rt288x,rt3883: Name DTS files based on scheme")

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-04 15:22:54 +01:00
Chuanhong Guo
09fe0c847d mediatek: add mt7629 subtarget with rfb image
base-files are added into subtarget directory like what's done
recently in ath79. For this subtarget, metadata checks are enforced
and a SUPPORTED_DEVICE is added to generate proper metadata.
Since we only have mt7629 support in 4.19, override KERNEL_PATCHVER
in target.mk for now.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-11-04 20:51:19 +08:00
Chuanhong Guo
58b0d3ecd6 mediatek: cosmetic fixes for mt7629-lynx-rfb
This patch did the following things:
1. rename device compatible string
2. add earlycon into cmdline
3. add mac address location according to mt7629 eeprom layout
4. rename mtd partitions
5. replace spaces for indentation with tabs

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-11-04 20:51:19 +08:00
Chuanhong Guo
109e614d90 mediatek: backport upstream patches related to mt7629 support
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-11-04 20:51:19 +08:00
Chuanhong Guo
46a97fe316 mediatek: fix Unielec U7623 dts in 4.19
remove duplicated pinctrl nodes.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-11-04 20:51:19 +08:00
Adrian Schmutzler
a5428d8c9b x86: delete empty Makefile introduced by accident
When changing profile titles for this target, an empty Makefile
has been added by accident.

Fixes: 14d17306bc ("x86: make profile titles more verbose")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-04 12:10:37 +01:00
Kristian Evensen
5f108bbc58 ramips: add support for ZBT WE1026-H
This commit adds support for the ZBT WE1026-H, an outdoor AP with
support for adding an internal LTE modem. The detailed specs are:

* CPU: MT7620A
* 2x 10/100Mbps Ethernet (LAN port has passive PoE support).
* 16/32 MB Flash.
* 128/256 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slot (only USB2.0 bus).
* 1x SIM slot (standard size).
* 1x 2.4Ghz WIFI (rt2800).
* 1x button.
* 6x LEDS (4 GPIO-controlled).
* 1x micro-SD reader.

The following have been tested and working:
- Ethernet switch
- Wifi
- Mini-PCIe slot + SIM slot
- USB port
- microSD slot
- sysupgrade
- reset button

Installation and recovery:

In order to install OpenWRT the first time or ito recover the router,
you can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address. Upload the firmware to start the recovery
process.

Notes:

* When binding the USB LED to a usbport, the LED is switched on all the
time due to the presence of an internal hub. Thus, it does not really
signal any USB-information.

* I only have the 32MB version and have only added support for this
device. However, the files are structured so that adding support for the
16MB version should be easy.

* Only the LAN port is accessible from the outside of the casing and LEDs
are not visible.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[rebased onto base-files split, minor style fixes, removed use of
USB led as power LED]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 15:10:22 +01:00
Kristian Evensen
a033f14fe9 ramips: update ZBT WE1026 DTS-files
This commit makes the following changes to the WE1026 DTS-files:

* The parts that are unique to the -5G-version (LED and 5GHz wifi)
are moved to a separate file, so that WE1026.dtsi can be referenced also
by the DTS for the -H version.
* Use the generic "flash"-name for the spi-nor node.
* Add label MAC.

All changes have been tested on the WE1026-5G-16M and work fine. I.e.,
the device works as before the DTS-changes.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Mathias Kresin <dev@kresin.me>
Acked-by: Alex Maclean <monkeh@monkeh.net>
Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
[minor style fixes, rebased onto base-files split, remove obsolete
gpio-keys comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 15:10:14 +01:00
Adrian Schmutzler
65d76175a5 ramips: improve common definition for Netgear R6xxx in mt7621.mk
This patch renames and reassembles the common definition for
Netgear R6xxx devices in mt7621.mk. The following goals should be
achieved:
- Give the node a more generic name instead of adding devices to it
- Use the common definition in the (less) similar R6220 node
- Include/exclude settings into the common definition so the common
  node contains the common definitions
- Prepare for support of R6700 v2

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 14:00:04 +01:00
Bernhard Geier
3930aab2cb ath79: add support for TP-Link WBS210 v2
TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with
two Ethernet ports based on Atheros AR9344

The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm
instead of 12 dBm) and two antenna connectors instead of built-in antennas.

Specifications:
 - SoC: Atheros AR9344
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
 - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP: 192.168.0.100
Stock device TFTP adress: 192.168.0.254

The TP-Link WBS devices use the same GPIOs as the CPE devices,
except for the link4 LED. For this one, WBS devices use "2", while
CPE devices use "16". (Tested on WBS210 v2)

Signed-off-by: Bernhard Geier <freifunk@geierb.de>
[added comment about GPIO]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 13:59:18 +01:00
Yousong Zhou
66ebca7103 build: label kernel and rootfs ext4 volumes
UUID of ext4 volumes generated by make_ext4fs are determined by volume
label and it will all be 57f8f4bc-abf4-655f-bf67-946fc0f9f25b when label
is empty

Labeling them does not make them unique but tools like block command
from fstools have a better chance differentiating them

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2019-11-03 04:25:40 +00:00
Adrian Schmutzler
fe534392a5 ath79: revert erroneous second addition of files for WNDR4300
There are two recent commits stating to add support for Netgear
WNDR4300, where the second one seems to be just leftover from
an earlier patch having been rebased.

Since the first patch already provides support in the most recent
state, just revert the second one.

This reverts commit cd87272eb2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 00:46:59 +01:00
Chih-Wei Chen
3e88ab79b0 ramips: fix Xiaomi MiWiFi Mini switch definition
Based on OpenWRT Table of Hardware > Xiaomi > Xiaomi Mi WiFi Mini

Switch Ports Defaults:
0, 1: LAN
4: WAN
6: CPU

Port in Web GUI (word printed on bottom of case)
WAN(Internet) map to switch port 4
LAN1(.) map to switch port 1
LAN2(..) map to switch port 0
CPU map to switch port 6

current setting is 1 WAN/ 4 LAN port, fix it.

Signed-off-by: Chih-Wei Chen <changeway@gmail.com>
[rebased after base-files split, fixed commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 00:30:20 +01:00
Paul Spooren
14d17306bc x86: make profile titles more verbose
So far (nearly) all x86 profiles are called "Generic" which makes
it hard to distinguish them in special cases, like searching for a
specific profile (without pre-selecting target/subtarget).

To make this change locally working, remove the tmp/ folder to
force reload of menuconfig.

As these files are infrequently touched, the Copyright was updated
as well.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[changed commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 00:30:09 +01:00
Rasim Kalimullin
81f7af4881 ath79: add support for TP-Link TL-WR1045ND v2
Specifications:
 - QCA9558 Soc
 - 720/800 (CPU/DDR)
 - 1x 10/100/1000 Mbps WAN Ethernet
 - 4x 10/100/1000 Mbps LAN Ethernet
 - 64 MB RAM (DDR2)
 - 8 MB FLASH
 - QCA9558 2.4 GHz 802.11bgn
 - 1x USB 2.0

Flash instruction
WebUI:
Download *-factory.bin image, rename to tp_firmware.bin and upload
it via the firmwary upgrade function of the stock firmware WebUI.

Tftp:
Rename OpenWRT or original firmware to wr1045v2_tp_recovery.bin and
Change your computer ip in 192.168.0.66 and subnet mask in 255.255.255.0.
Router will obtain IP 192.168.0.86 for a few seconds while loading,
when reset button pressed at power On.

Signed-off-by: Rasim Kalimullin <neutrino.vm@gmail.com>
[rebased onto base-files split]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 00:29:55 +01:00
Roger Pueyo Centelles
20ace70db6 ath79: remove wmac mtd-mac-address for UniFi AC family
The MAC address for the wmac 2.4 GHz radio of the Ubiquiti UniFi AC
family of devices is actually embedded in the mtd-cal-data, so there
is no need for mtd-mac-address (which was incorrectly forcing wmac
to have the same MAC as eth0). This makes it coherent with the stock
firmware and the ar71xx target:

 · XX:XX:XX:X0:XX:XX eth0
 · XX:XX:XX:X1:XX:XX ath0/wlan1 (2.4 GHz)
 · XX:XX:XX:X2:XX:XX ath1/wlan0 (5 GHz)

Checked on a UniFi AC Mesh, a UniFi AC LR and a UniFi Lite.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-11-03 00:29:40 +01:00
Adrian Schmutzler
194612997b ath79: use nand_do_upgrade by default for nand subtarget
On nand subtarget, the default upgrade mechanism should be
nand_do_upgrade. This patch changes platform_do_upgrade()
accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 00:29:12 +01:00
Adrian Schmutzler
19724e28c8 ramips: split base-files into subtargets
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.

However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space.

In certain cases, keeping files in parent (=target) base-files was
more convenient, and thus no splitting was performed for those.

Note that this will increase overall code lines, but reduce code
per subtarget.

base-files ipk size reduction:
master (mt7621)   60958 B
split (mt7620)    46358 B (- 14.3 kiB)
split (mt7621)    48759 B (- 11.9 kiB)
split (mt76x8)    44948 B (- 15.6 kiB)
split (rt288x)    43508 B (- 17.0 kiB)
split (rt305x)    45616 B (- 15.0 kiB)
split (rt3883)    44176 B (- 16.4 kiB)

Run-tested on:
GL.iNet GL-MT300N-V2 (mt76x8)
D-Link DWR-116 (mt7620)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 00:26:17 +01:00
Adrian Schmutzler
0975c35b83 ramips: add newline for ASUS RT-ACx5P DTSes
Those files are missing the newline at the end.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 00:23:35 +01:00
Adrian Schmutzler
999504ff65 ath79: remove further redundant mtd-mac-address for wmac
For several devices, wmac MAC address is set from art 0x1002
explicitly by using mtd-mac-address although mtd-cal-data is
pulled from art 0x1000.

With the MAC address in 0x1002, the driver should automatically
use it when reading caldata from 0x1000. Thus, remove the
redundant mtd-mac-address for those devices.

This patch addresses the cases where the calibration data partition
is not labelled art, having been overlooked in the first patch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-02 20:51:56 +01:00
Adrian Schmutzler
dc90caf45a ipq40xx: convert IMAGE_SIZE/KERNEL_SIZE/BLOCKSIZE to kiB
This cosmetical patch converts IMAGE_SIZE, KERNEL_SIZE and
BLOCKSIZE definitions to kilobytes, as this is consistent and
easier to read/type.

An exception was made for asus_rt-ac58u, where the IMAGE_SIZE of
20439364 cannot be divided by 1024 (and also does not seem to
match anything in DTS).

Build-tested for all devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-02 20:51:56 +01:00
Adrian Schmutzler
6d00e6fc7b ath79: fix several issues for ZyXEL NBG6716
This fixes several issues introduced with ZyXEL NBG6716 support:
- Inhomogeneous indent
- Wrong ath10k MAC patching function
- Wrong brackets for pad-to in nand.mk
- Add missing DEVICE_MODEL
- Remove k2t.sh include (copy/paste leftover)

Fixes: 99835e0999 ("ath79: add support for ZyXEL NBG6716")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-02 20:51:56 +01:00
Michal Cieslakiewicz
cd87272eb2 ath79: add support for Netgear WNDR4300
This patch adds ath79 support for Netgear WNDR4300.
Router was previously supported by ar71xx target only.
Note: device requires 'ar934x-nand' driver in kernel.

Specification
=============
  * Description: Netgear WNDR4300
  * Loader: U-boot
  * SOC: Atheros AR9344 (560 MHz)
  * RAM: 128 MiB
  * Flash: 128 MiB (NAND)
	- U-boot binary: 256 KiB
	- U-boot environment: 256 KiB
	- ART: 256 KiB
	- POT: 512 KiB
	- Language: 2 MiB
	- Config: 512 KiB
	- Traffic Meter: 3 MiB
	- Firmware: 25 MiB
	- ART Backup: 256 KiB
	- Reserved: 96 MiB
  * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327)
  * Wireless:
	- 2.4 GHz b/g/n (internal)
	- 5 GHz a/n (AR9580)
  * USB: yes, 1 x USB 2.0
  * Buttons:
	- Reset
	- WiFi (rfkill)
	- WPS
  * LEDs:
	- Power (amber/green)
	- WAN (amber/green)
	- WLAN 2G (green)
	- WLAN 5G (blue)
	- 4 x LAN (amber/green)
	- USB (green)
	- WPS (amber/green)
  * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 2.5A
  * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Note about partitioning: firmware partition offset (0x6c0000) is
hardcoded into vendor's u-boot, so this partition cannot be moved
and resized to include Netgear-specific flash areas (pot, language,
config, traffic_meter) not used by OpenWrt.

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-11-02 20:51:56 +01:00
Michal Cieslakiewicz
9b6f89c37f ath79: add support for Netgear WNDR4300
This patch adds ath79 support for Netgear WNDR4300.
Router was previously supported by ar71xx target only.
Note: device requires 'ar934x-nand' driver in kernel.

Specification
=============
  * Description: Netgear WNDR4300
  * Loader: U-boot
  * SOC: Atheros AR9344 (560 MHz)
  * RAM: 128 MiB
  * Flash: 128 MiB (NAND)
	- U-boot binary: 256 KiB
	- U-boot environment: 256 KiB
	- ART: 256 KiB
	- POT: 512 KiB
	- Language: 2 MiB
	- Config: 512 KiB
	- Traffic Meter: 3 MiB
	- Firmware: 25 MiB
	- ART Backup: 256 KiB
	- Reserved: 96 MiB
  * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327)
  * Wireless:
	- 2.4 GHz b/g/n (internal)
	- 5 GHz a/n (AR9580)
  * USB: yes, 1 x USB 2.0
  * Buttons:
	- Reset
	- WiFi (rfkill)
	- WPS
  * LEDs:
	- Power (amber/green)
	- WAN (amber/green)
	- WLAN 2G (green)
	- WLAN 5G (blue)
	- 4 x LAN (amber/green)
	- USB (green)
	- WPS (amber/green)
  * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 2.5A
  * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Note about partitioning: firmware partition offset (0x6c0000) is
hardcoded into vendor's u-boot, so this partition cannot be moved
and resized to include Netgear-specific flash areas (pot, language,
config, traffic_meter) not used by OpenWrt.

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-11-02 19:29:30 +01:00
Daniel Danzberger
affe633be4 ipq40xx: ipq4019: Add new device Compex WPJ419
This device contains 2 flash devices. One NOR (32M) and one NAND (128M).
U-boot and caldata are on the NOR, the firmware on the NAND.

    SoC:    IPQ4019
    CPU:    4x 710MHz ARMv7
    RAM:    256MB
    FLASH:  NOR:32MB NAND:128MB
    ETH:    2x GMAC Gigabit
    POE:    802.3 af/at POE, IEEE802.3af/IEEE802.3at(48-56V)
    WIFI:   1x 2.4Ghz Atheros qca4019 2x2 MU-MIMO
            1x 5.0Ghz Atheros qca4019 2x2 MU-MIMO
    USB:    1x 3.0
    PCI:    1x Mini PCIe
    SIM:    1x Slot
    SD:     1x MicroSD slot
    BTN:    Reset
    LED:    - Power
            - Ethernet
    UART:  1x Serial Port 4 Pin Connector (UART)
           1x Serial Port 6 Pin Connector (High Speed UART)
    POWER: 12V 2A

Installation
------------
Initial flashing can only be done via u-boot using the following commands:

tftpboot openwrt-ipq40xx-generic-compex_wpj419-squashfs-nand-factory.ubi
nand erase.chip; nand write ${fileaddr} 0x0 ${filesize}
res

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
2019-11-02 19:25:15 +01:00
Michal Cieslakiewicz
f85d56bb03 ath79: add support for Netgear WNR2200
This patch adds ath79 support for Netgear WNR2200.
Router was previously supported by ar71xx target only (8 MiB variant).
Netgear WNR2200 has two flash versions - 8MiB sold in EU, US etc. and
16 MiB for Russia and China markets. Apart from flash size both variants
share the same hardware specification.

Specification
=============
  * Description: Netgear WNR2200
  * Loader: U-boot
  * SOC: Atheros AR7241 (360 MHz)
  * RAM: 64 MiB
  * Flash: 8 MiB or 16 MiB (SPI NOR)
	- U-boot binary: 256 KiB
	- U-boot environment: 64 KiB
	- Firmware: 7808 KiB or 16000 KiB
	- ART: 64 KiB
  * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
  * Wireless: 2.4 GHz b/g/n (Atheros AR9287)
  * USB: yes, 1 x USB 2.0
  * Buttons:
	- Reset
	- WiFi (rfkill)
	- WPS
  * LEDs:
	- Power (amber/green)
	- WAN (amber/green)
	- WLAN (blue)
	- 4 x LAN (amber/green)
	- WPS (green)
  * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 1.5A
  * MAC addresses: LAN on case label, WAN +1, WLAN +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_generic=y
CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200-8m=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-11-01 21:14:55 +01:00
Koen Vandeputte
df60a0852c kernel: bump 4.19 to 4.19.81
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-31 09:17:14 +01:00
Koen Vandeputte
0e212220e9 kernel: bump 4.14 to 4.14.151
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-31 09:17:14 +01:00
Koen Vandeputte
4b2ab533d4 kernel: bump 4.19 to 4.19.80
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-30 11:16:25 +01:00
Koen Vandeputte
0787b7247f kernel: bump 4.14 to 4.14.150
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-30 11:16:25 +01:00
Rafał Miłecki
b49f2113cc kernel: fix swconfig compilation with kernels 5.2+
This is related to the upstream kernel change 3b0f31f2b8c9 ("genetlink:
make policy common to family").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-10-28 17:01:00 +01:00
David Bauer
a8a9340609 ath79: fix incorrect identation in qca9557.dtsi
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-27 18:03:56 +01:00
Adrian Schmutzler
b288c56e1e ath79: move base-files for ZyXEL NBG6716
Due to rebase of the base-files split patch after adding support
for the ZyXEL NBG6716, its base-files were added to the generic
subtarget, although the device belongs to the nand subtarget.

This moves the definitions to their proper locations.

Fixes: 0130022bae ("ath79: split base-files into subtargets")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[improve commit message, rebase]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-27 18:03:56 +01:00
David Bauer
62db255543 ath79: add support for Aerohive HiveAP 121
This commit adds support for the Aerohive HiveAP-121. It was previously
already supported in the ar71xx subtarget.

The following is copied from the commit which added ar71xx support:

Specification:
- SoC: Atheros AR9344-BC2A at 560MHz
- WiFi 1: 2.4GHz Atheros AR9340? - SoC
- WiFi 2: 5.0GHz Atheros AR9382-AL1A
- Memory: 128MB from 2x Nanya NT5TU32M16DG-AC
- SPI: 1MB Macronix MX25L8006E
- NAND: 128MB Hynix H27U1G8F2BTR-BC
- Ethernet: Atheros AR8035-A
- USB: 1x 2.0
- TPM: Atmel SC3204

Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, download and flash LEDE factory image over tftp:

dhcp;
setenv serverip tftp-server-ip;
tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin;
nand erase 0x800000 0x800000;
nand write 0x81000000 0x800000 0x800000;
reset;

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-27 18:03:56 +01:00
David Bauer
08a134820f ath79: enable PCI for whole target
This commit adds PCI support for the whole ath79 target. Previously,
this was only done in the generic and tiny subtargets.

With the introduction of the HiveAP-121, PCI will be a requirement for
all subtargets, thus moving PCI support to the target configuration.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-27 18:02:55 +01:00
Adrian Schmutzler
2b1baf9b16 ath79: remove redundant mtd-mac-address for wmac
For several devices, wmac MAC address is set from art 0x1002
explicitly by using mtd-mac-address although mtd-cal-data is
pulled from art 0x1000.

With the MAC address in 0x1002, the driver should automatically
use it when reading caldata from 0x1000. Thus, remove the
redundant mtd-mac-address for those devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Jeff Kletsky <git-commits@allycomm.com>
Tested-by: Karl Palsson <karlp@etactica.com>
2019-10-27 18:02:44 +01:00
David Bauer
6f2e1b7485 ath79: disable delays on AT803X config init
Until upstream commit 6d4cd041f0af("net: phy: at803x: disable delay
only for RGMII mode"), delays were not disabled on driver probe
for the Atheros AR803x PHYs, although the RX delay is enabled on
soft and hard reset.

In addition, the TX delay setting is retained on soft-reset.

This patch disables both delays on config init to align the behavior
with kernel 5.1 and higher. It can be safely dropped with kernel 5.1.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-27 17:56:23 +01:00
Adrian Schmutzler
0130022bae ath79: split base-files into subtargets
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.

However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space (especially helpful for the tiny devices).

The only script remaining in parent base-files is
/etc/hotplug.d/ieee80211/00-wifi-migration, everything else is
moved/split.

Note that this will increase overall code lines, but reduce code
per subtarget.

base-files ipk size reduction:
master (generic)   49135 B
split (generic)    48533 B (- 0.6 kiB)
split (tiny)       43337 B (- 5.7 kiB)
split (nand)       44423 B (- 4.6 kiB)

Tested on TL-WR1043ND v4 (generic) and TL-WR841N v12 (tiny).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 14:24:22 +01:00
Rosen Penev
c36ef5970b ramips: ethernet: Replace random_ether_addr with eth_hw_addr_random
eth_hw_addr_random additionally sets addr_assign_type to NET_ADDR_RANDOM.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2019-10-27 14:13:47 +01:00
Adrian Schmutzler
0b2a2f4380 ipq40xx: add label MAC address for Netgear EX6100v2/EX6150v2
This is based on the EX6150v2, which should be identical to
the EX6100v2:

The device bears two MAC addresses ("MAC 1" and "MAC 2") that
correspond to phy0 and phy1.

The ethernet MAC address (gmac0) is the same as phy0.
As this one is accessible via local-mac-address in gmac0, the
latter is used for label-mac-device.

(Although this is a one-port, gmac1 also has a local-mac-address
assigned. This has the same vendor part as the other addresses,
but completely different data for the device part.)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 14:03:43 +01:00
Adrian Schmutzler
dc7872d8f8 ipq40xx: use DEVICE_VARIANT for Unielec U4019 flash size
If flash size is used as part of a device's title, it should be
specified as DEVICE_VARIANT like for the other devices so far.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 14:03:21 +01:00
Adrian Schmutzler
2d2fa2fd2d ath79: fix remaining IMAGE_SIZE issues
This fixes the remaining IMAGE_SIZE issues in ath79 target.
All devices in target have been checked, so together with
previous patches this target should be "clean" afterwards.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 14:03:03 +01:00
Adrian Schmutzler
4b4856bc53 ath79: fix IMAGE_SIZE for common TP-Link definitions
So far, IMAGE_SIZE is set as follows:
tplink-4m*   3904k  0x3d0000
tplink-8m*   7936k  0x7c0000
tplink-16m* 15872k  0xf80000

However, based on the size of firmware partitions in DTS it should
be:
tplink-4m*   3904k  0x3d0000
tplink-8m*   8000k  0x7d0000
tplink-16m* 16192k  0xfd0000

All (!) 8m*/16m* devices actually follow the latter scheme, which
is also consistent in terms of left free space for other
partitions. Thus, fix it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 14:02:43 +01:00
Adrian Schmutzler
3202ee0fc6 ath79: tidy up and fix IMAGE_SIZE for Ubiquiti devices
This addresses IMAGE_SIZE inconsistencies in generic_ubnt.mk by:

1. (cosmetical) Move IMAGE_SIZE out of top definition ("ubnt"),
   since despite two all subdefinition have different values.
2. (change) Fix IMAGE_SIZE for ubnt-xm and ubnt-bz (7552k->7488k).
3. (cosmetical) Move IMAGE_SIZE of ubnt-wa devices to parent node
   since all have same size (it is defined in parent DTSI ...).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 14:02:27 +01:00
Michal Cieslakiewicz
3f275f2ac8 ath79: wnr1000v2: fix image header information
Factory image generated for Netgear WNR1000 v2 has incorrect device
and hardware ID information in header due to missing makefile
variables. This fix adds them to device section.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-27 13:42:31 +01:00
André Valentin
99835e0999 ath79: add support for ZyXEL NBG6716
Attention: Kernel partition size has been enlarged to 4MB.
To switch, you must update to latest ar71xx-nand snapshort and flash the
sysupgrade-4M-Kernel.bin:

zcat openwrt-ath79-nand-zyxel_nbg6716-squashfs-sysupgrade-4M-Kernel.bin | mtd -r -e ubi write - firmware; reboot -f
You will end up with a fresh config if you do not inject config into the image.

The NBG6716 may come with 128MB or 256MB NAND. ar71xx was able to use all, but
ath79 can only use the first 128MB. Therefore the complete NAND needs to be
overwritten. If not, the old UBI may make problems and lead to reboot loop.

Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:

|   Hit any key to stop autoboot:  3

The user is then dropped to a locked shell.

|NBG6716> HELP
|ATEN    x[,y]     set BootExtension Debug Flag (y=password)
|ATSE    x         show the seed of password generator
|ATSH              dump manufacturer related data in ROM
|ATRT    [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO              boot up whole system
|ATUR    x         upgrade RAS image (filename)
|NBG6716>

In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!

First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.

|NBG6716> ATSE NBG6716
|012345678901

This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):

- tool.sh -
ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -

|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711

copy and paste the result into the shell to unlock zloader.

|NBG6716> ATEN 1,0046B0017430

If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.

|NBG6716> ATGU
|NBG6716#

Signed-off-by: André Valentin <avalentin@marcant.net>
2019-10-27 13:38:49 +01:00
André Valentin
353ecbbf64 ar71xx: fix bug in NBG6716 kernelpacking, add firmware partition
-Fix the kernel image generation (more robust)
-Add a firmware partition table allowing easy upgrade to ath79

Signed-off-by: André Valentin <avalentin@marcant.net>
2019-10-27 13:38:25 +01:00
Paul Fertser
522d5ff428 ramips: add support for Xiaomi Mi Wi-Fi Router 3G v2
- CMIIT ID: 2019AP2581
- SoC:      MediaTek MT7621
- Flash:    16MiB NOR SPI (GigaDevice GD25Q128B)
- RAM:      128MiB DDR3 (ESMT M15T1G1664A)
- Serial:   As marked on PCB, 3V3 logic, baudrate is 115200, 8n1
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0:    MT7603E 2.4GHz 802.11b/g/n
- WIFI1:    MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs:     Programmable "power" LED (two-coloured, yellow/blue)
            Non-programmable "internet" LED (shows WAN activity)
- Buttons:  Reset

INSTALLATION:

Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on". Vendor firmware (looks like
an illegal OpenWrt fork) won't accept any serial input unless
"uart_en" is set to "1". Tricks to force u-boot to use default
environment do not help as it's restricted in the same way.

With bootloader unlocked the easiest way would be to TFTP the
sysupgrade image or to sysupgrade after loading an initramfs one.

For porting the flash contents were changed externally with an SPI
programmer (after lifting Vcc flash IC pin away from the PCB).

Forum thread [0] indicates that this device is identical to "Xiaomi Mi
Router 4A Gigabit Edition".

[0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685

Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-10-27 12:25:56 +01:00
Tim Harvey
d3d06f1500 octeontx: fix thunderx BGX underflow irq name
request_irq requires irq names to be static/allocated and not on the stack

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-10-27 12:13:59 +01:00
Adrian Schmutzler
1abb473cea ramips: remove phy0tpt trigger from RT-AC65P/RT-AC85P power LED
This patch removes a phy0tpt trigger from the power LED, which
seems to have been added by mistake.

WiFi LEDs using phy0radio and phy1radio triggers are present and
used correctly.

Cc: Birger Koblitz <mail@birger-koblitz.de>

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 12:13:48 +01:00
Adrian Schmutzler
b6d53f1d02 ramips: remove redundant mtd-eeprom in mt76x8 DTS files
In mt7628an.dtsi, calibration data for wmac is already defined:
mediatek,mtd-eeprom = <&factory 0x0>;

Thus, this patch removes redundant entries of this property in
derived DTS files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 12:13:06 +01:00
Adrian Schmutzler
547720fb48 ramips: remove redundant mtd-mac-address for WiFi
When caldata locations are defined with mediatek,mtd-eeprom the
MAC address is automatically read from offset +4. Thus, specifying
that location explicitly is redundant.

This patch removes those redundant definitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 12:12:50 +01:00
Jeff Kletsky
b9d58f7e06 kernel: mtd: spinand: Backport chip definitions
generic: Add/rename patches for upstream consistency

ipq40xx: generic-level patch replaces same-source patches-4.19/
         082-v4.20-mtd-spinand-winbond-Add-support-for-W25N01GV.patch

The SPI-NAND framework from Linux uses common driver code that is then
"tuned" by a tiny struct of chip-specific data that describes
available commands, timing, and layout (data and OOB data). Several
manufacturers and chips have been added since 4.19, several of which
are used in devices already supported by OpenWrt (typically with no or
"legacy" access to their NAND memory). This commit catches up the
supported-chip definitions through Linux 5.2-rc6 and linux/next.

The driver is only compiled for platforms with CONFIG_MTD_SPI_NAND=y.
This presently includes ipq40xx and pistachio, with the addition of
ath79-nand in these commits (and not ath79-generic or ath79-tiny).

Upstream patches refreshed against 4.19.75

Build-tested-on: ipq40xx
Run-tested-on: ath79-nand

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-10-24 23:07:47 +02:00
Jeff Kletsky
18848312c5 ath79: Refactor GL.iNet GL-AR300M-series generic.mk
Rework DEVICE_VENDOR, DEVICE_MODEL, and DEVICE_VARIANT
for the GL-AR300M series on the ath79-generic target.

Changes GL-AR300M-Lite to the current form with
DEVICE_VARIANT := Lite (board name is unchanged)

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-10-24 23:06:26 +02:00
Jeff Kletsky
1f748df085 ath79: GL-AR750S: Add I2C Support
The GL-AR750S has an internal header for I2C.

Provide DTS definitions for the i2c-gpio driver.

The I2C drivers; kmod-i2c-core, kmod-i2c-gpio
consume ~20 kB of flash and can be loaded as modules,

Default clock measured ~11.2 ms period, ~89 kHz

The board has well-labeled (unpopulated) headers for serial and I2C
along the front edge of the board (the edge with the LEDs). Looking
from the top, rear of the unit (behind Ethernet jacks)

  -------------------------------------------
       5G_LED        2G_LED      PWR_LED

                 O O O O O O O

                 3 S S G T R G
                 V C D N X X N
                 3 L A D     D

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-10-24 23:00:49 +02:00
Jeff Kletsky
736d16baad ath79: GL-AR300M series: Add I2C Support
The GL-AR300M series have an internal header for I2C.

Provide DTS definitions for the i2c-gpio driver.

The I2C drivers; kmod-i2c-core, kmod-i2c-gpio
consume ~20 kB of flash and can be loaded as modules,

Default clock measured ~11.4 ms period, ~88 kHz

The board has two sets of (unpopulated) headers.  While facing the
back of the board (looking into the Ethernet jacks), and looking from
the top, the one on the left edge of the baord with four holes is the
I2C header. It appears to be labeled J8 on "GL-AR300M-V1.4.0" boards.

    | (Patch antenna)
    |
    |
    |  O   GND
    |  O   SDA / GPIO 17
    |  O   SCL / GPIO 16
    |  ⊡   3V3 (square land)
    |
    | (Ethernet jacks)

https://docs.gl-inet.com/en/3/hardware/ar300m/#pcb-pinout states
"Note: I2C is not working in some early version of the router."

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-10-24 23:00:36 +02:00
Gabor Varga
7c5f712e4f ramips: add support for Asus RT-AC65P
The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it.

On both routers the installation can be done also via SSH:

Note: The user/password for SSH is identical with the one used in the
Web-interface.

1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt factory image via scp:
 > scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp
4. Connect via SSH to the router.
 > ssh admin@192.168.50.1
5. Write the OpenWrt image to flash.
 > mtd-write -i
/tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux
6. Reboot the router
 > reboot

Changelog:

v3: removed [] from filename, rebased to latest master
v2: Rebased to latest master
v1: Initial release

Signed-off-by: Gabor Varga <vargagab@gmail.com>
2019-10-24 22:58:02 +02:00
Andreas Ziegler
2bc7c519dc ar71xx: add model detection for UniFi AC-LR
This commit adds correct model detection for UniFi
AC-LR. Previously, said device was incorrectly detected
as UniFi-AC-LITE/MESH.

The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[adjust naming style of target to existing ones]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-23 12:31:48 +02:00
David Bauer
7f187229a8 ipq40xx: add support for AVM FRITZ!Repeater 1200
Hardware
--------
SoC:   Qualcomm IPQ4019
RAM:   256M DDR3
FLASH: 128M NAND
WiFi:  2T2R IPQ4019 bgn
       2T2R IPQ4019 a/n/ac
ETH:   Atheros AR8033 RGMII PHY
BTN:   1x Connect (WPS)
LED:   Power (green/red/yellow)

Installation
------------

1. Grab the uboot for the Device from the 'u-boot-fritz1200'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ1200.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz1200.bin uboot0
   > mtd write /path/to/uboot-fritz1200.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-23 01:17:28 +02:00
David Bauer
6fd9eeeeb2 ipq40xx: add missing backslash in 11-ath10k-caldata
This adds a missing backslash in the caldata-extraction script. Without
this fix, caldata extraction fails for every device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-23 01:17:28 +02:00
David Bauer
7be79a3ab2 ipq40xx: fix ethernet probe abort on missing phy-reset
This commit completely fixes the abortion of the ipq40xx ethernet driver
probe in case no phy-reset is defined.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-23 01:17:28 +02:00
Moritz Warning
d263883796 brcm63xx: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Uses DEVICE_ALT* variables for alternative vendor/retailer names.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-10-22 22:05:21 +02:00
Jonas Gorski
4f86397022 brcm63xx: fix build with GCC 8.3
Fixes the following build error when building when using GCC 8.3:

In file included from ./include/linux/string.h:19,
                 from ./include/linux/bitmap.h:9,
                 from ./include/linux/cpumask.h:12,
                 from ./arch/mips/include/asm/processor.h:15,
                 from ./arch/mips/include/asm/thread_info.h:16,
                 from ./include/linux/thread_info.h:38,
                 from ./include/asm-generic/preempt.h:5,
                 from ./arch/mips/include/generated/asm/preempt.h:1,
                 from ./include/linux/preempt.h:81,
                 from ./include/linux/spinlock.h:51,
                 from ./include/linux/mmzone.h:8,
                 from ./include/linux/bootmem.h:8,
                 from arch/mips/bcm63xx/prom.c:10:
arch/mips/bcm63xx/prom.c: In function 'prom_init':
./arch/mips/include/asm/string.h:162:11: error: '__builtin_memcpy' forming offset [2, 32] is out of the bounds [0, 1] of object 'bmips_smp_movevec' with type 'char' [-Werror=array-bounds]
   __ret = __builtin_memcpy((dst), (src), __len); \
           ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/mips/bcm63xx/prom.c:97:3: note: in expansion of macro 'memcpy'
   memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20);
   ^~~~~~
In file included from arch/mips/bcm63xx/prom.c:14:
./arch/mips/include/asm/bmips.h:80:13: note: 'bmips_smp_movevec' declared here
 extern char bmips_smp_movevec;

Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2019-10-22 21:41:59 +02:00
Adrian Schmutzler
fd1d03f853 ramips: fix LAN/WAN MAC addresses of Xiaomi MiWiFi Mini board
Based on stock firmware tests, both LAN and WAN ports use the
MAC address from 0x28 on factory partition.

In OpenWrt, this one is already set in DTS. This patch removes the
local bit set in 02_network previously, and adjusts LAN/WAN
addresses as on stock firmware.

Note that in tests we found a MAC address in 0x2e that is the one
in 0x28 plus 1. Since stock firmware does not use it though, we
do not use it either.

Thanks to Chih-Wei Chen for testing this on his device.

ref: https://github.com/openwrt/openwrt/pull/2497

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-22 11:45:50 +02:00
John Crispin
8285af1928 ipq40xx: fix optional gpio-reset
If a gpio reset pin was not defined we should not bog out.

Signed-off-by: John Crispin <john@phrozen.org>
2019-10-22 00:00:36 +02:00
Adrian Schmutzler
c79b796280 ar71xx: improve support for TP-Link CPE510 v2
This fixes commit bae927c551 ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.

Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).

With this patch, we provide proper support for this device in ar71xx.

Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
  for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254

Fixes: bae927c551 ("ar71xx: add support for TP-LINK CPE510 V2.0")
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-10-21 21:54:01 +02:00
Adrian Schmutzler
e4155bcc45 ramips: fix TARGET_DEVICES after UniElec rename
Device node names were updated, but updating TARGET_DEVICES
was overlooked.

Fixes: 4408723d42 ("ramips: remove RAM size from device name
for UniElec devices")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 18:36:45 +02:00
Adrian Schmutzler
4408723d42 ramips: remove RAM size from device name for UniElec devices
UniElec devices are the last ones in ramips target still having
the RAM size in device name although RAM size is auto-detected.

Remove this from device name, compatible, etc., as it's not
required and might be misleading to users and developers adding
device support copying those devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:27:30 +02:00
Tomasz Maciej Nowak
cc5256a8bf ath79: base-files: disable sysupgrade for routerstations and ja76pf2
Previous commit 0cc87b3 "ath79: image: disable sysupgrade images for
routerstations and ja76pf2" doesn't remedy completely the posibility of
bricking the device, since user could try to downgrade with an older
image. Therefore disable sysupgrade code for these boards with a small
note.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-10-21 14:23:39 +02:00
Adrian Schmutzler
8c36fd3105 ath79: apply alphabetical sorting to entries in 10_fix_wifi_mac
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:22:47 +02:00
Adrian Schmutzler
244745d7fc ath79: remove empty default case in 10_fix_wifi_mac
This removes a useless empty default case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:22:33 +02:00
Adrian Schmutzler
44da2e0344 ath79: fix whitespaces in 10_fix_wifi_mac
This converts leading whitespaces to tabs and removes a double
newline at the end of the file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:22:19 +02:00
Adrian Schmutzler
556ff09875 ramips/mt762x: convert devices to interrupt-driven gpio-keys
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.

While at it, add/remove newlines in keys and leds node where
necessary.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:19:32 +02:00
Adrian Schmutzler
53e6cc7a81 ath79: add LED migration for several Archer Cxx devices
Several Archer Cxx devices were using board-specific LED names in
ar71xx, which were changed to "tp-link:*" in ath79.

This patch adds migration for them.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:12:07 +02:00
Adrian Schmutzler
6b0eb84336 ath79: use board name in LED migrations
Several devices added to LED migration script will just have their
(old) board name converted to tp-link.

By using a variable for this, the amount of code in the migration
script can be reduced and the chance for typos is reduced.

This patch also introduces the marker for beginning of a pattern
"^" to the regex, so the match is more specific.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:11:47 +02:00
Adrian Schmutzler
e816c50993 ramips: fix whitespace issues in DTS files
This is the result of grepping/searching for several common
whitespace issues like double empty lines, leading spaces, etc.

This patch fixes them for the ramips target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:10:47 +02:00
Adrian Schmutzler
f473ce6f23 ath79: fix SUPPORTED_DEVICES for ubnt_nanostation-m
The ar71xx images for the Ubiquiti NanoStation M (XM) devices use
"nanostation-m" as board name, but the ath79 images are only
compatible with the "nano-m" board name, so sysupgrade complains.

By changing this additional supported device, sysupgrade smoothly
upgrades from ar71xx to ath79.

Ref: openwrt#2418

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 13:33:24 +02:00
Adrian Schmutzler
86a1f52617 lantiq: modify ath9k caldata extraction to reuse caldata.sh
In lantiq, ath9k caldata extraction is implemented to work in two
alternate "modes", the standard one and another one with swapped
byte pairs.

This rearranges the functions so "standard" use is based on the
caldata.sh library, while only a single local function is required
for the special case.

Note that while the parameter for switching between normal and swab
is removed, the size of the caldata is added to the function calls
to stay consistent.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 13:28:58 +02:00
Michal Cieslakiewicz
380cf82f99 ar71xx: WNDR4300: fix WAN LED behaviour
Change WAN LED behaviour to be consistent with other Netgear
routers running OpenWrt. Instead of link speed, use amber colour
to indicate link status. Green LED should be used when Internet
connection is up and running.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-21 13:24:27 +02:00
Michal Cieslakiewicz
77e14181d9 ar71xx: WNDR4300: use standard labels for buttons
GPIO key labels have been changed to standard ones (rfkill, reset, wps).
It does not affect button functionality.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-21 13:24:01 +02:00
Adrian Schmutzler
6b53033783 ath79: fix patching ath9k MAC address for MyNet WiFi Range Extender
The code line patching ath9k MAC address for this device contains
a wrong number of arguments including an unset "$mac", which
looks like a typo or copy/paste mistake.

This has been introduced already in the device support commit
745dee11ac ("ath79: add support for WD My Net Wi-Fi Range
Extender").

This patch just removes the "$mac" argument, leaving a formally
valid line. (No on-device test has been performed.)

Cc: Christian Lamparter <chunkeey@gmail.com>

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 13:20:24 +02:00
Michal Cieslakiewicz
09f46c6b54 ath79: add support for Netgear WNR1000 v2
This patch adds ath79 support for Netgear WNR1000v2.
Router was previously supported by ar71xx target only.
Note: this is a 4_32 device with limited upgrade capabilities.

Specification
=============
  * Description: Netgear WNR1000 v2
  * Loader: U-boot
  * SOC: Atheros AR7240 (340 MHz)
  * RAM: 32 MiB
  * Flash: 4 MiB (SPI NOR)
	- U-boot binary: 256 KiB
	- U-boot environment: 64 KiB
	- Firmware: 3712 KiB
	- ART: 64 KiB
  * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
  * Wireless: 2.4 GHz b/g/n (Atheros AR9285)
  * USB: no
  * Buttons:
	- Reset
	- WiFi (rfkill)
	- WPS
  * LEDs:
	- Power (amber/green)
	- WAN (amber/green)
	- WLAN (blue)
	- 4 x LAN (amber/green)
	- WPS (green)
  * UART: 4-pin connector JP2, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 1A
  * MAC addresses: LAN on case label, WAN +1, WLAN +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_tiny=y
CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr1000-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-21 13:15:46 +02:00
Michal Cieslakiewicz
12719ce37a ath79: add support for Netgear WNR2000 v3
This patch adds ath79 support for Netgear WNR2000v3.
Router was previously supported by ar71xx target only.
Note: this is a 4_32 device with limited upgrade capabilities.

Specification
=============
  * Description: Netgear WNR2000 v3
  * Loader: U-boot
  * SOC: Atheros AR7241 (360 MHz)
  * RAM: 32 MiB
  * Flash: 4 MiB (SPI NOR)
	- U-boot binary: 256 KiB
	- U-boot environment: 64 KiB
	- Firmware: 3712 KiB
	- ART: 64 KiB
  * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
  * Wireless: 2.4 GHz b/g/n (Atheros AR9287)
  * USB: no
  * Buttons:
	- Reset
	- WiFi (rfkill)
	- WPS
  * LEDs:
	- Power (amber/green)
	- WAN (amber/green)
	- WLAN (blue)
	- 4 x LAN (amber/green)
	- WPS (green)
  * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 1A
  * MAC addresses: LAN on case label, WAN +1, WLAN +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_tiny=y
CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr2000-v3=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-21 13:15:19 +02:00
Michal Cieslakiewicz
d74324e407 ath79: WNR612v2: improve device support
This patch improves ath79 support for Netgear WNR612v2.
Router functionality becomes identical to ar71xx version.

Changes include:
* software control over LAN LEDs via sysfs
* correct MAC addresses for network interfaces
* correct image size in device definition
* dts: 'keys' renamed to 'ath9k-keys'
* dts: 'label-mac-device' set to eth1 (LAN)
* dts: formatting adjustments

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-21 13:15:05 +02:00
Michal Cieslakiewicz
69df7eb73d ath79: add LAN LEDs control bits for AR724x GPIO function pinmux
Currently AR724x pinmux for register 0x18040028 controls only JTAG disable bit.
This patch adds new DTS settings to control LAN LEDs and CLKs that allow
full software control over these diodes - exactly the same is done by ar71xx
target in device setup phase for many routers (WNR2000v3 for example).

'switch_led_disable_pins' clears AR724X_GPIO_FUNC_ETH_SWITCH_LED[0-4]_EN bits.
'clks_disable_pins' clears AR724X_GPIO_FUNC_CLK_OBS[1-5]_EN and
AR724X_GPIO_FUNC_GE0_MII_CLK_EN bits. These all should be used together, along
with 'jtag_disable_pins', to allow OS to control all GPIO-connected LEDs and
buttons on device.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-21 13:14:52 +02:00
Tomasz Maciej Nowak
1bc921f419 ath79: add support for Sitecom WLR-7100
Sitecom WLR-7100 v1 002 (marketed as X7 AC1200) is a dual band wireless
router.

Specification
SoC: Atheros AR1022
RAM: 64 MB DDR2
Flash: 8 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R QCA9882 integrated (connected to PCIe lane)
Ethernet: 5x 10/100/1000 Mbps QCA8337N
USB: 1x 2.0
LEDS: 4x GPIO controlled, 5x switch
Buttons: 2x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
      white triangle on PCB
      1. VCC 3.3V, 2. GND, 3. TX, 4. RX
      baud: 115200, parity: none, flow control: none

Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Toolbox > Firmware,
4. Browse for OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
   is ready for configuration.

Known issues
5GHz LED doesn't work

Additional information
When TX line on UART is connected, and board is switched on from power
off state, the DDR memory training may fail.
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), which may or may
not work with introduced images.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-10-21 13:01:10 +02:00
Kristian Evensen
6f6c00cfc9 ipq40xx: Add support for Unielec U4019
This commit adds support for the 32MB storage/512MB RAM version of the U4019
IPQ4019-based board from Unielec. The board has the following specifications:

* Qualcomm IPQ4019 (running at 717MHz)
* 512MB DDR3 RAM (optional 256MB/1GB)
* 32MB SPI NOR (optional 8/16MB or NAND)
* Five gigabit ports (Qualcomm QCA8075)
* 1x 2.4 GHz wifi (QCA4019 hw1.0)
* 1x 5 Ghz wifi (QCA4019 hw1.0)
* 1x mini-PCIe slot (only USB-pins connected)
* 1x SIM slot (mini-SIM)
* 1x USB2.0 port
* 1x button
* 1x controllable LED
* 1x micro SD-card reader

Working:
* Ethernet
* Wifi
* USB-port
* mini-PCIe slot + SIM slot
* Button
* Sysupgrade

Not working:
* SD card slot (no upstream support)

Installation instructions:

In order to install OpenWRT on the U4019, you need to go via the
initramfs-image. The installation steps are as follows:

* Connect to board via serial (header exposed and clearly marked).
* Interrupt bootloader by pressing a button.
* Copy the initramfs-image to your tftp folder, call the file C0A80079.img.
* Give the network interface connected to the U4019 the address
192.168.0.156/24.
* Start your tftp-server and run tftpboot on the board.
* Run bootm when the file has been transferred, to boot OpenWRT.
* Once OpenWRT has booted, copy the sysupgrade-image to the device and run
sysupgrade to install OpenWRT on the U4019.

Notes:

- Since IPQ4019 has been moved to 4.19, I have not added support for kernel
4.14.

- There is a bug with hardware encryption on IPQ4019, causing poor performance
with TCP and ipsec (see for example FS#2355). In order to improve performance,
I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if
bug is fixed.

- In order for Ethernet to work, the phy has to be reset by setting gpio 47
low/high. Adding support for phy reset via gpio required patching the
mdio-driver, and the code added comes from the vendor driver. I do not know if
patching the driver is an acceptable approach or not.

v1->v2:
* Do not use wildcard as identifier in the board.d-scripts (thanks
Adrian Schmutzler).

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-21 12:28:03 +02:00
Daniel Gimpelevich
ee41b602a2 ath79: fix gigabit link pll-data for EX7300
The device did not appear to be reachable unless the connection were
forced to 100Mb or lower. Revert to previously working pll-data.

Also fix the phy-mode to represent the actual state needed for ethernet
to function.

Reported-by: Moritz Schreiber <moritz@mosos.de>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[add remark about phy-mode property]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-21 09:06:52 +02:00
Michal Cieslakiewicz
758a4d1766 ath79: add AR934x NAND Flash Controller driver
This patch contains updated driver for Atheros NAND Flash Controller
written originally by Gabor Juhos for ar71xx (aka 'ar934x-nfc').
ath79 version has adapted to work with kernel 4.19 and Device Tree.
It has also been renamed to 'ar934x-nand' to avoid confusion with
Near-Field Communication technology.
Controller is present on Atheros AR934x SoCs and required for accessing
internal flash storage on routers like Netgear WNDR4300.
This port preserves all NAND programming code while moving platform
configuration to Device Tree and replacing some kernel functions marked
for retirement by 4.19.
Suitable definition is included in 'ar934x.dtsi' ('nand@1b000200' section).

Most important changes to ar71xx version are:
* old kernel sections of code removed
* 'bool swap_dma' provided by platform data is now set by boolean DT
  property 'qca,nand-swap-dma'
* board-supplied (mach-*.c code) platform data removed - its elements
  become either unused, redundant or replaced by DT methods (like reset)
* IRQ is reserved by devm_request_irq() so free_irq() is not needed anymore
* calls to deprecated nand_scan_ident() + nand_scan_tail() function pair
  replaced by using recommended nand_scan() with attach_chip() callback
* ECC is set to hardware by default, can be overriden by standard DT
  'nand-ecc-*' properties (software Hamming or BCH are other options)

This driver has been successfully tested on Netgear WNDR4300 running
experimental ath79 OpenWrt master branch.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[add reset control]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-20 15:32:53 +02:00
Masafumi UTSUGI
f1d761f95e ipq40xx: essedma: Fix dead lock
edma_read_append_stats() gets called from two places in the driver.
The first place is the kernel timer that periodically updates
the statistics, so nothing gets lost due to overflows.
The second one it's part of the userspace ethtool ioctl handler
to provide up-to-date values.

For this configuration, the use of spin_lock() is not sufficient
and as per:
<https://mirrors.edge.kernel.org/pub/linux/kernel/people/rusty/kernel-locking/c214.html>
the locking has to be upgraded to spin_lock_bh().

Signed-off-by: Masafumi UTSUGI <mutsugi@allied-telesis.co.jp>
[folded patch into 710-, rewrote message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-10-20 13:01:43 +02:00
Jeff Kletsky
f5c7fe2ff0 ath79: Clean up GL-AR300M DTS/DTSI inclusions
Modify GL-AR300M-Lite and GL-AR300M (NOR):

* Include qca9531_glinet_gl-ar300m.dtsi directly
  rather than qca9531_glinet_gl-ar300m-nor.dts

* Remove redundant inclusion of gpio.h and input.h

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-20 13:01:43 +02:00
Hauke Mehrtens
16f84fd275 kernel: Fix arm64 include files
This patch fixes the build of gdb and strace on arm64 targets with
kernel 4.19.

Without this patch asm/ptrace.h is including asm/sigcontext.h and this
file defines some structures which are also defined in musl header file
arch/aarch64/bits/signal.h. These two definitions then conflict with
each other and make the build fail.

This was seen locally and also by the build bot. The struct sigcontext,
struct sve_context and some others were defined twice. It looks like
this problem was introduced between 4.14 and 4.19 and it was fixed in
5.0. I already requested to backport this patch to kernel 4.19.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-10-20 12:33:40 +02:00
Moritz Warning
34939711a5 ath25: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-10-19 13:16:57 +02:00
Moritz Warning
88f8b63a3d mvebu: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-10-19 13:16:57 +02:00
Moritz Warning
0aca8dc6ad mediatek: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-10-19 13:16:57 +02:00
Moritz Warning
036f1d9bac octeon: split up remaining DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR and DEVICE_MODEL

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-10-19 13:16:57 +02:00
Moritz Warning
e6114ff925 at91: split up remaining DEVICE_TITLE definitions
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-10-19 13:16:57 +02:00
Moritz Warning
1997feb2ff rb532: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-10-19 13:16:57 +02:00
Biwen Li
53b73131e9 kernel: layerscape: fix compilation error
This fixes a compilation error as follows:
drivers/staging/fsl_qbman/qman_config.c:815:29: error: bitwise comparison
always evaluates to false [-Werror=tautological-compare]
  if ((qman_ip_rev & 0xFF00) == QMAN_REV31) {

Signed-off-by: Biwen Li <biwen.li@nxp.com>
2019-10-19 13:16:57 +02:00
Christian Lamparter
54d9ac8ba8 ipq806x: WPQ864: fix partition unit-address
This patch fixes what seems to be a simple copy & paste
error with the unit-address of the BOOTCONFIG partition.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-10-18 21:05:34 +02:00
Adrian Schmutzler
d1072096f4 ramips: fix WiFi MAC addresses for D-Link DIR-810L
So far, WiFi MAC addresses for this device have been set up from
caldata. However, this returns values which do not look like MAC
addresses. They also do not match stock firmware:

wlan0 (5.0): 00:11:22:00:17:D0 from 0x8004
wlan1 (2.4): 00:11:22:00:17:CD from 0x4 (and 0x2e)

It looks like the only valid MAC address on this device is at 0x28.

So, this patch changes setup to calculate addresses based on the
value at 0x28:

lan: *:0A (flash, label)
wan: *:0B (flash + 1)
wifi2: *:0A (flash)
wifi5: *:0C (flash + 2)

Thanks to Roger Pueyo Centelles <roger.pueyo@guifi.net> for
investigating this on his devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-15 23:31:13 +02:00
Martin Schiller
71e04091a9 lantiq: fix dsl_control status handling.
Commit 7519a36774 ("base-files,procd: add generic service status")
introduced the generic 'status' command which broke the previous
dsl_control status output. To fix this, let's rename the "old" command
to "dslstat".

Fixes: 7519a36774 ("base-files,procd: add generic service status")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-10-15 23:23:08 +02:00
Dan Haab
63c43e5674 bcm53xx: sysupgrade: support Luxul NAND devices
This adds support for UBI-aware sysupgrade using Luxul formats.

Signed-off-by: Dan Haab <dan.haab@legrand.com>
2019-10-15 20:23:04 +02:00
Michael Heimpold
e56e5a454e brcm47xx: fix switch port labels for Asus WL500GP V2
The switch port naming in LuCI does not fit the physical numbers
on the front of this device. Since this is confusing, fix it.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2019-10-15 20:22:42 +02:00
Adrian Schmutzler
48b5d08a48 treewide: use a single ath10k MAC patching function with checksum
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).

This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.

This patch adds checksum adjustments for several targets on
ath79 and lantiq.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-15 18:13:54 +02:00
Adrian Schmutzler
332b1f46e9 ipq40xx: add label MAC address for FritzBox 4040
The CWMP-Account on the device's label contains the eth0 MAC
address.

This only changes 4.19 files as label-mac-device is introduced
after 19.07 branch, so there won't be a 4.14 release anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-15 18:13:54 +02:00
David Bauer
1a256470e7 ath79: correct ar71xx boardname for UniFi AC Lite
This corrects the additional boardname for the image metadata to the one
used in ar71xx. The previously present additional entry was never used
on a running system.

Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-15 18:13:54 +02:00
David Bauer
07e555d873 mpc85xx: correct TP-LINK TL-WDR4900 MAC addresses
This commit fixes TP-Link TL-WDR4900 v1 MAC address assignment.
Previously, the MAC addrss was read for the ethernet from the "config"
partition. However, the content of this partition is dependent on the
firmware which was previously installed on the device.

Switch the MAC address source to the U-Boot partition, where the MAC
address is always present at a fixed partition. The partition was
previously already used for the WiFi MAC-addresses.

Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-15 18:13:54 +02:00
Andreas Ziegler
07c1ddf522 ath79: add support for UniFi AC-LR
The Unifi AC-LR has identical hardware to the Unifi AC-Lite.
The antenna setup is different according to the vendor,
which explains the thicker enclosure.

Therefore, it is helpful to know the exact device variant,
instead of having "Ubiquiti UniFi-AC-LITE/LR".

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[fix legacy name in commit message; add old boardname to
SUPPORTED_DEVICES]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-15 18:13:54 +02:00
Koen Vandeputte
e5445333f6 kernel: bump 4.19 to 4.19.79
Refreshed all patches.

Remove upstreamed (superseded):
- 950-0726-can-mcp251x-Allow-more-time-after-a-reset.patch

Compile-tested on: brcm2708, cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-15 16:11:28 +02:00
Koen Vandeputte
1cfe412dd2 kernel: bump 4.14 to 4.14.149
Refreshed all patches.

Altered patches:
- 820-sec-support-layerscape.patch

Compile-tested on: cns3xxx, layerscape
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-15 16:11:28 +02:00
Adrian Schmutzler
2c60de0e3f treewide: move MAC address patch functions to common library
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-14 12:36:02 +02:00
Adrian Schmutzler
5b6a809092 treewide: move calibration data extraction function to library
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.

Functions are renamed with more generic names to merge different
variants that only differ in their names.

Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-13 21:48:58 +02:00
Adrian Schmutzler
c1388a2deb base-files: move xor() from caldata extraction to functions.sh
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-13 19:03:57 +02:00
Roger Pueyo Centelles
bba6646b5c ath79: add support for COMFAST CF-E313AC
This patch adds support for the COMFAST CF-E313AC, an  outdoor wireless
CPE with two Ethernet ports and a 802.11ac radio.

Specifications:

 - QCA9531 SoC
 - 650/400/216 MHz (CPU/DDR/AHB)
 - 1x 10/100 Mbps WAN Ethernet, 48V PoE-in
 - 1x 10/100 Mbps LAN Ethernet, pass-through 48V PoE-out
 - 1x manual pass-through PoE switch
 - 64 MB RAM (DDR2)
 - 16 MB FLASH
 - QCA9886 2T2R 5 GHz 802.11ac, 23 dBm
 - 12 dBi built-in antenna
 - POWER/LAN/WAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1)

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI. Settings from the original firmware
 will be saved and restored on the new one, so a factory reset will be
 needed. To do so, once the new firmware is flashed, enter into failsafe
 mode by pressing the reset button several times during the boot
 process, while the WAN LED flashes, until it starts flashing faster.
 Once in failsafe mode, perform a factory reset as usual.

 Alternatively, the U-boot bootloader contains a recovery HTTP server
 to upload the  firmware. Push the reset button while powering the
 device on and keep it pressed for >10 seconds. The device's LEDs will
 blink several times and the recovery page will be at
 http://192.168.1.1; use it to upload the sysupgrade image.

Note:

 Four MAC addresses are stored in the "art" partition (read-only):
  - 0x0000: 40:A5:EF:AA:AA:A0
  - 0x0006: 40:A5:EF:AA:AA:A2
  - 0x1002: 40:A5:EF:AA:AA:A1
  - 0x5006: 40:A5:EF:AA.AA:A3 (inside the 5 GHz calibration data)

 The stock firmware assigns MAC addresses to physical and virtual
 interfaces in a very particular way:
  - eth0 corresponds to the physical Ethernet port labeled as WAN
  - eth1 corresponds to the physical Ethernet port labeled as LAN

  - eth0 belongs to the bridge interface br-wan
  - eth1 belongs to the bridge interface br-lan

  - eth0 is assigned the MAC from 0x0 (*:A0)
  - eth1 is assigned the MAC from 0x1002 (*:A1)

  - br-wan is forced to use the MAC from 0x1002 (*:A1)
  - br-lan is forced to use the MAC from 0x0 (*:A0)

  - radio0 uses the calibration data from 0x5000 (which contains
    a valid MAC address, *:A3). However, it is overwritten by the
    one at 0x6 (*:A2)

 This commit preserves the LAN/WAN roles of the physical Ethernet
 ports (as labeled on the router) and the MAC addresses they expose
 by default (i.e., *:A0 on LAN, *:A1 on WAN), but swaps the position
 of the eth0/eth1 compared to the stock firmware:
  - eth0 corresponds to the physical Ethernet port labeled as LAN
  - eth1 corresponds to the physical Ethernet port labeled as WAN

  - eth0 belongs to the bridge interface br-lan
  - eth1 is the interface at @wan

  - eth0 is assigned the MAC from 0x0 (*:A0)
  - eth1 is assigned the MAC from 0x1002 (*:A1)

  - br-lan inherits the MAC from eth0 (*:A0)
  - @wan inherits the MAC from eth1 (*:A1)

  - radio0's MAC is overwritten to the one at 0x6

This way, eth0/eth1's positions differ from the stock firmware, but
the weird MAC ressignations in br-lan/br-wan are avoided while the
external behaviour of the router is maintained. Additionally, WAN
port is connected to the PHY gmac, allowing to monitor the link
status (e.g., to restart DHCP negotiation when plugging a cable).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-10-13 20:34:57 +08:00
Roger Pueyo Centelles
ac36cca012 ramips: mt7621: Alternative name KE 2P for Phicomm K2P
The Phicomm KE 2P is identical to the already supported Phicomm K2P,
renamed for the European market. Use the ALT0 buildroot tags to show
both devices.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-10-13 20:34:57 +08:00
Martin Schiller
c5829788c9 lantiq: add set_port_link feature to xrx200-net driver
This makes it possible to configure the link attributes (aneg, duplex,
speed) of each switch ports.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-10-12 23:43:08 +02:00
Scott Roberts
d2a1075973 mvebu: backport mvneta and comphy from linux 5.x
These patches backport support for the ARMADA 3700 COMPHY driver.
Also backported is the mvneta driver.  This will allow switching
the SGMII speed using SMC calls.  To support this you must update
the firmware using Marvells 18.12 version (this has now been
upstreamed).  The mvneta driver allows 2500basex and 2500baset.

Signed-off-by: Scott Roberts <ttocsr@gmail.com>
2019-10-12 23:43:08 +02:00
Eubert Bao
e11fc8439c kirkwood: Fix FS#505 - Can't install LEDE on Linksys EA3500
The default sizes render Device/linksys_audi mage un-flashable.
Restore the pagesize, subpagesize, and blocksize for linksys_audi
from https://github.com/openwrt/archive.

Signed-off-by: Eubert Bao <bunnier@gmail.com>
2019-10-12 23:42:59 +02:00
Moritz Warning
66fbaae83e pistachio: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-10-12 23:37:00 +02:00
Sungbo Eo
b83b2d76ca ar71xx: remove unnecessary execute permission bit
.c files do not need to be executable. 644 is enough.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-10-12 23:37:00 +02:00
Sungbo Eo
68014f6d6e mediatek: remove unnecessary execute permission bit
kernel config and dts files do not need to be executable. 644 is enough.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-10-12 23:37:00 +02:00
Hauke Mehrtens
ace1bfb554 mvebu: Refresh kernel 4.19 configuration
This refreshes the kernel 4.19 configuration, it looks like this was not
done initially.

When did a compile with the default settings I had to select some
kernel configuration options.

Fixes: 98684d99b2 ("mvebu: add kernel 4.19 support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-10-12 23:37:00 +02:00
Hauke Mehrtens
e901ce6f0e kernel: Set GCC version to 80300 by default
The kernel 4.19 configuration contains the GCC version used, set it to
8.3.0 as this is now our default compiler.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-10-12 22:38:02 +02:00
Moritz Warning
c3ffb0e7d5
brcm47xx: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-10-12 01:43:07 +02:00
Moritz Warning
f3c21d1517
omap: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-10-12 01:22:46 +02:00
Oldřich Jedlička
e0ce80d42a kernel: Fix off-by-one error in FIT mtd partition search.
This fixes off-by-one error introduced in commit dc76900021
("kernel: Correctly search for the FIT image in mtd partition.")

Function `mtd_read` starts reading at `offset` and
needs `hdr_len` number of bytes to be available. Suppose
the easiest case when `offset` is `0` and `hdr_len` equals
to `mtd->size` - the `for` loop will not be entered even
when enough bytes are available to be read.

Same happens for any non-zero `offset`, when `hdr_len` is
just enough bytes to be read until `mtd->size` is reached.
Imagine that for example `mtd->size=5`, `offset=4` and
`hdr_len=1`. Then `offset+hdr_len=5` and the check has to
be `offset+hdr_len <= mtd->size`, i.e. `5 <= 5`. The
check for `offset + hdr_len` value needs to be inclusive,
therefore use `<=`.

Fixes: dc76900021 ("kernel: Correctly search for the FIT image in mtd partition.")
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
[adjusted commit ref, fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-10-09 14:45:25 +02:00
Martin Schiller
b204fcdb07 target/imagebuilder: use multi-thread support for xz compression
This speeds up the packing of the imagebuilder a lot:

 imagebuilder-T0.tar.xz real 0m25.199s user 2m45.967s sys 0m1.218s
 imagebuilder-T1.tar.xz real 2m02.543s user 2m02.418s sys 0m1.653s
 imagebuilder-T2.tar.xz real 1m03.684s user 1m59.931s sys 0m0.587s
 imagebuilder-T3.tar.xz real 0m48.033s user 2m02.904s sys 0m0.637s
 imagebuilder-T4.tar.xz real 0m38.963s user 2m15.521s sys 0m0.783s
 imagebuilder-T5.tar.xz real 0m37.994s user 2m21.461s sys 0m0.919s
 imagebuilder-T6.tar.xz real 0m39.524s user 2m48.115s sys 0m1.279s
 imagebuilder-T7.tar.xz real 0m34.061s user 2m45.097s sys 0m1.174s
 imagebuilder-T8.tar.xz real 0m27.286s user 2m55.449s sys 0m1.329s
 imagebuilder-T9.tar.xz real 0m25.205s user 2m44.894s sys 0m1.208s

To keep the output reproducible in any case, we enforce a minimum amount
of 2 threads.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[refactored into reusable NPROC var, more verbose commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-10-09 09:13:44 +02:00
Koen Vandeputte
8184429b7b kernel: bump 4.19 to 4.19.78
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-08 15:51:06 +02:00
Koen Vandeputte
4648533ca4 kernel: bump 4.14 to 4.14.148
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-08 15:51:06 +02:00
Koen Vandeputte
f516ce3b10 kernel: bump 4.9 to 4.9.196
Refreshed all patches.

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-08 15:51:06 +02:00
Koen Vandeputte
8e197c7af2 kernel: bump 4.19 to 4.19.77
Refreshed all patches.

Remove upstreamed:
- 110-ARM-zynq-Use-memcpy_toio-instead-of-memcpy.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-08 12:44:35 +02:00
Koen Vandeputte
9b04a7576b kernel: bump 4.14 to 4.14.147
Refreshed all patches.

Altered patches:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ar71xx)
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ath79)

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-08 12:44:35 +02:00
Koen Vandeputte
65fad9fec5 kernel: bump 4.9 to 4.9.195
Refreshed all patches.

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-08 12:44:35 +02:00
Adrian Schmutzler
273a6cb562 ath79: improve DTS for TP-Link Archer D50 v1
This addresses several issues in the DTS file:
- add diag LED support
- remove unused node names
- fix whitespace issues

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-06 22:42:30 +02:00
Davide Fioravanti
67d019ac94 ramips: enable LED VCC for Asus RT-AC51U
Previously only the power LED was working.
With this patch all leds except 5GHz are working.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[rephrased commit title, drop status property]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-06 21:28:49 +02:00
Adrian Schmutzler
929becbc2d ath79: fix whitespace issues in DTS files
This is the result of grepping/searching for several common
whitespace issues like double empty lines, leading spaces, etc.

This patch fixes them for the ath79 target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-06 21:28:49 +02:00
Adrian Schmutzler
794d4b6652 treewide: remove kmod-usb-core from DEVICE_PACKAGES
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.

This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-06 21:28:49 +02:00
Andre Heider
3b874c2c81 sunxi: update kernel config
This is just a `make kernel_oldconfig` run without further changes.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2019-10-06 21:28:49 +02:00
Koen Vandeputte
7449a39c0e kernel: bump 4.19 to 4.19.76
Refreshed all patches.

Altered patches:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch

Compile-tested on: ath79, cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-04 15:48:28 +02:00
Rafał Miłecki
fedc5b65dc bcm53xx: fix serial console on Luxul XWC-2000
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-10-04 15:46:23 +02:00
Rafał Miłecki
64b7dbb300 bcm53xx: fix sysupgrade for Luxul XWC-2000
Use a correct "compatible" value as in the upstream DTS file.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-10-04 11:41:32 +02:00
Rafał Miłecki
06091afada bcm53xx: add pending patch adding Luxul XWC-2000 DTS file
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-10-04 10:07:00 +02:00
Jeff Kletsky
eba0db95b5 ath79: Restore GL.iNet GL-AR300M-Lite first-boot connectivity
The relationship between GMAC0 and GMAC1 and the kernel devices
eth0 and eth1 was reversed for many ath79 devices by commit 8dde11d521
ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi

The GL-AR300M-Lite is a single-port device, with the "LAN" port of the
GL-AR300M board unpopulated and its sole port now referenced as eth1,
as a result of commit 8dde11d521. The device was unreachable on
first boot or fresh config.

By changing &eth1 (GMAC1) to an MFD, GMAC0 is able to associate with
the phy and is known by the kernel as "eth0".

Thanks to Chuanhong Guo for the suggestion of "simple-mfd"

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-09-29 00:46:14 +02:00
Jeff Kletsky
474b69475d ath79: Correct glinet, gl-ar300m-lite in 02_network
Previously, the board name for the GL-AR300M-Lite was incorrect
in 02_network, resulting in an unintended, fall-through condition
when initializing the network configuration.

While builds prior to commit 8dde11d521 (merged June 5, 2019)
    ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi
functioned properly, the error was noted in resolving first-boot
connectivity issues related to the single-phy nature of the device
and the "swap" of eth0 and eth1 related to that commit.

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-09-29 00:46:14 +02:00
Adrian Schmutzler
22e876fdb0 ramips: add label MAC address for Asus RT-AC85P
The label shows the MAC address of 2.4 GHz WiFi.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-29 00:46:13 +02:00
Adrian Schmutzler
0aab49d234 treewide: fix hex2dec conversion for MAC address checksum offset
If chksum_offset is converted by $(($...)) at the beginning, the
check [ -n "$chksum_offset" ] will always return true, as the
conversion yields "0" for an empty argument, and [ -n "0" ] is
true.

With this patch, the variable is not converted before the check,
but only when it's used in dd.

No conversion is done for use in hexdump, as this can deal with
hex value offsets.

Fixes: b133e466b0 ("treewide: convert WiFi caldata size and offset to hexadecimal")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-29 00:46:13 +02:00
Adrian Schmutzler
c5b4fa20fa treewide: replace backticks by $(...) in gen_*_img.sh scripts
This replaces deprecated backticks by more versatile $(...) syntax.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[decapitalized patch subject at submitter's request]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-09-29 00:46:13 +02:00
Adrian Schmutzler
0bbfc3dff7 octeon: replace backticks by $(...)
This replaces deprecated backticks by more versatile $(...) syntax.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[decapitalized patch subject at submitter's request]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-09-29 00:46:13 +02:00
Adrian Schmutzler
aea3cab77a lantiq: replace backticks by $(...) and remove useless echo
This replaces deprecated backticks by more versatile $(...) syntax.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[decapitalized patch subject at submitter's request]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-09-29 00:46:13 +02:00
Adrian Schmutzler
a421a12f9c orion: replace backticks by $(...)
This replaces deprecated backticks by more versatile $(...) syntax.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[decapitalized patch subject at submitter's request]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-09-29 00:46:13 +02:00
Adrian Schmutzler
81c52edf2b mvebu: replace backticks by $(...)
This replaces deprecated backticks by more versatile $(...) syntax.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[decapitalized patch subject at submitter's request]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-09-29 00:46:13 +02:00
Eneas U de Queiroz
9de9e9c6c5 ipq806x: remove unsupported hw-crypto qce driver
The following symbols, selected by the qce driver were removed:
	CONFIG_CRYPTO_CBC
	CONFIG_CRYPTO_CTR
	CONFIG_CRYPTO_DES
	CONFIG_CRYPTO_DEV_QCE
	CONFIG_CRYPTO_ECB
	CONFIG_CRYPTO_NULL
	CONFIG_CRYPTO_SEQIV
	CONFIG_CRYPTO_XTS

CONFIG_CRYPTO_GF128MUL was removed as well, since it is only needed by
some cipher modes (LRW, GCM), none of which are selected, and it is
packaged as a module.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2019-09-29 00:46:13 +02:00
Christian Lamparter
95f2bb24be apm821xx: fix fan control on highest step
This patch removes a typo (extra "0") so that the 'cpu-alert6'
step is triggered once the system reaches 85°C.

Note: Unless the WNDR4700 is placed in an hot oven, the
hardware-monitor will never reach this value.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-09-29 00:46:13 +02:00
Adrian Schmutzler
400e56d22c ramips: apply consistent device name/compatible to ZBT-WE1026-5G
All Zbtlink ramips devices except the ZBT-WE1026-5G include the
zbt-/ZBT- prefix in their model name.

This changes ZBT-WE1026-5G to also follow that scheme.

The patch moves some block to keep alphatical order.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-29 00:08:20 +02:00
Adrian Schmutzler
b376818f97 ramips: harmonize device vendor Zbtlink
Spelling of Zbtlink varies across image definitions and DTS files.

This patch uses Zbtlink consistently and also updates the model
in DTS files to contain the vendor in all cases.

This patch is cosmetical, as there should be no dependencies on
device model name in ramips anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-29 00:08:20 +02:00
Rafał Miłecki
9d95d5e799 brcm47xx: sysupgrade: fix device model detection
$(board_name) was providing content on "boardtype" (and optionally
"boardnum") NVRAM values. That function requires & expects more specific
and detailed model name extracted from the /proc/cpuinfo.

Fixes: f12a32630f ("treewide: use the generic board_name function")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-26 06:51:16 +02:00
Adrian Schmutzler
fddea2030e ath79: remove redundant ucidef_set_interfaces_* calls in 02_network
If already included in ucidef_add_switch, you do not have to
additionally set the interface mode in ucidef_set_interfaces_*
functions.

This patch removes/adjusts such redundant cases.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-25 22:42:03 +02:00
Adrian Schmutzler
724875b8d0 ramips: merge cases in 02_network
This merges three cases with a single switch port.

6t@eth0 and 6@eth0 should be equivalent.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-25 22:42:03 +02:00
David Bauer
e2c084cabc ipq40xx: abort ar40xx probe on missing PHYs
The ar40xx driver currently panics in case no QCA807x PHY has been
successfully probed. This happens when the external PHY is still
in reset when probing the ar40xx switch driver.

Note that this patch does not fix the root cause, ar40xx_probe now
simply fails instead of causing a kernel panic due to a nullpointer
dereference.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-25 22:42:03 +02:00
Felix Fietkau
c8933ce533 kernel: fix issues with output routing in flow offload
Replace an old cleanup patch that never made it upstream with the proper
upstream fix. This patch was incompatible with the recent changes that
affected the way that the flow tuple dst entry was used.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-09-25 20:11:20 +02:00
Felix Fietkau
442ecce761 kernel: port 4.19 xt_FLOWOFFLOAD changes to 4.14
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-09-25 18:16:39 +02:00
Felix Fietkau
a438eac9ac kernel: port another missing upstream change to xt_FLOWOFFLOAD on 4.19
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-09-25 18:16:39 +02:00
Moritz Warning
661e37ccea layerscape: split up DEVICE_TITLE definitions
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-25 12:50:24 +02:00
Linus Walleij
19f722adef gemini: dir685: Restore graphics
One of the v4.19 patches had a bug, this is fixed upstream,
but in OpenWrt we can fix it by just fixing the bug in the
patch.

We also need to augment the config file to select the
CONFIG_DRM_FBDEV_EMULATION symbol.

This restores the display controller on the DIR-685 to
working state: penguin and graphics on the little screen
with default OpenWrt install.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-09-25 12:50:24 +02:00
Felix Fietkau
3c14e384b7 kernel: update and fix xt_FLOWOFFLOAD target on 4.19
Merge upstream changes to nft_flow_offload.
Fixes offloading

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-09-25 11:10:33 +02:00
Adrian Schmutzler
7b8b4197d2 ramips: initialize youhua, wr1200js WAN MAC addresses from flash
This patch changes wan MAC address setup for youhua,wr1200js
from retrieving it by calculation to reading it from flash.

This has been checked on-device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-25 14:44:36 +08:00
INAGAKI Hiroshi
12ab6ef5c3 ramips: add support for I-O DATA WNPR2600G
I-O DATA WNPR2600G is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.

Specification:

- SoC           : MediaTek MT7621A
- RAM           : DDR3 128 MiB
- Flash         : SPI-NOR 16 MiB
- WLAN          : 2.4/5 GHz 4T4R
  - 2.4 GHz     : MediaTek MT7615
  - 5 GHz       : MediaTek MT7615
- Ethernet      : 10/100/1000 Mbps
  - Switch      : MT7530 (SoC)
- LED/keys      : 4x/3x (2x buttons, 1x slide-switch)
- UART          : through-hole on PCB
  - J1: Vcc, RX, GND, TX from SoC side
  - 57600n8

Flash instruction using factory image:

1. Boot WNPR2600G normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-09-25 14:44:36 +08:00
INAGAKI Hiroshi
c1394dabf6 ramips: move "elx-header" to Makefile from mt7620.mk and mt7621.mk
I-O DATA WNPR2600G has an "elx-header", so move this definition to
generic makefile to use it from mt7621 subtarget.
This definition is also added to mt7621.mk in
f285e8634c, so remove it from mt7621.mk.

And added a line to cleanup used header file.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-09-25 14:44:36 +08:00
INAGAKI Hiroshi
6c3ae072dc ramips: replace MAC address configuration for I-O DATA WN-AC-GR devices
following I-O DATA devices have a MAC address as "wanaddr" for WAN
interface in u-boot-env:

- WN-AC1167GR
- WN-AC733GR3

I replaced MAC address configuration in these devices to omit
address calculation in 02_network.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-09-25 14:44:36 +08:00
Sungbo Eo
b7ec6659a1 ramips: add support for ipTIME A3
ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.

Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
  - Switch: SoC internal
- UART:
  - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-09-25 14:44:36 +08:00
Qi Jiang
93b6cc97ca ramips: add support for XiaoYu XY-C5
Hardware:
SoC:      MT7621A
Flash:    32 MiB
RAM:      512 MiB
Ethernet: built-in switch
USB:      1x USB3.0
SATA:     ASM1060, 1 SATA port

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.173.22
2. Download *-sysupgrade.bin image and rename it to firmware.img
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Turn on router,press the reset button and wait ~15 seconds
6. Release the reset button and after a short time
   the firmware should be transferred from the tftp server
7. Wait ~3 minutes to complete recovery.

Signed-off-by: Qi Jiang <rushx@live.cn>
[squash commits, add label-mac-device, fix sign-off style]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-09-25 14:44:36 +08:00
Koen Vandeputte
e39d1cf34f kernel: bump 4.19 to 4.19.75
Refreshed all patches.

Fixes:
- CVE-2019-14814
- CVE-2019-14815
- CVE-2019-14816
- CVE-2019-14821

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-24 12:52:05 +02:00
Koen Vandeputte
b6686576b4 kernel: bump 4.14 to 4.14.146
Refreshed all patches.

Fixes:
- CVE-2019-14814
- CVE-2019-14815
- CVE-2019-14816
- CVE-2019-14821

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-24 12:52:05 +02:00
Koen Vandeputte
b1ec16d3c2 kernel: bump 4.9 to 4.9.194
Refreshed all patches.

Fixes:
- CVE-2019-14814
- CVE-2019-14815
- CVE-2019-14816
- CVE-2019-14821

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-24 12:52:05 +02:00
Adrian Schmutzler
8961d2268e ath79: convert devices to interrupt-driven gpio-keys
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.

Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as
this one is using ath9k keys.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Karl Palsson <karlp@etactica.com>
Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
2019-09-22 18:28:11 +02:00
Russell Senior
a03219ba09 apm821xx: remove unnecessary kernel padding
The allocation of LEBs to ubi volumes is handled by the sysupgrade script:

  package/base-files/files/lib/upgrade/nand.sh

and the ubimkvol and or ubirsvol command. Therefore, padding of the
kernel blob is not needed at all, so use cat instead of dd. The
BLOCKSIZE variable was only used in the dd command.  In any case, 63k
made no sense for the way BLOCKSIZE was being used.

63k (64512) does make sense for DTB_SIZE because of the offsets expected
by u-boot given extant u-boot-env variables.

Tested on Meraki MR24.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2019-09-21 23:41:31 +02:00
Dmitry Tunin
00ed75f47f ath79: add support of Netgear WNDR3800CH
Add support for the ar71xx supported Netgear WNDR3800CH to ath79.
The device is identical to WNDR3800 except NETGEAR_BOARD_ID.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-21 23:41:31 +02:00
Dmitry Tunin
edf1c6c67a ath79: DIR825B1 switch to gpio-keys
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2019-09-21 23:41:31 +02:00
Eneas U de Queiroz
391b14a892 ipq40xx: fix hw-crypto detection of qce driver
This adds the CRYPTO_ALG_KERN_DRIVER_ONLY flag to Qualcomm crypto engine
driver algorithms, so that openssl devcrypto can recognize them as
hardware-accelerated.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[refresh, move to ipq40xx as its the only target right now]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-09-21 23:41:31 +02:00
Adrian Schmutzler
f8d8b3f85d ath79: remove invalid uses of ath9k_patch_fw_mac_crc
Some ar9344-based devices are using ath9k_patch_fw_mac_crc, which
is meant to generate a checksum, for fixing their ath9k MAC
addresses.
However, those do not have a checksum field, and the calculated
checksum offset would be negative.

This patch will use ath9k_patch_fw_mac function for those devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-21 23:41:31 +02:00
Adrian Schmutzler
5b96421964 ramips: replace backticks by $(...)
This replaces deprecated backticks by more versatile $(...) syntax.

While at it, remove some useless cat commands and deprecated
egrep commands.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-21 22:17:39 +02:00
Tomasz Maciej Nowak
66b7c82bb1 ath79: image: pad kernel for Adtran/Bluesocket devices
It has been reported that using the sysupgrade-tar image will trigger
"lzma_decode failed error". The RedBoot bootloader always loads data
from flash till block size boundary, so if there's no padding it'll also
load the beginning of rootfs, and it seems that lzma_decoder can't handle
that garbage data. Previously the script creating combined-image
silently padded the kernel and rootfs, but since sysupgrade-tar doesn't,
pad the default kernel image.

Fixes: 900330f ("ath79: image: retire combined-image for Adtran/Bluesocket
devices")
Cc: Brian Gonyer <bgonyer@gmail.com>
Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-09-21 22:17:39 +02:00
Adrian Schmutzler
d1e3f32dcf ath79: sort device definitions in image/*
This applies alphabetic sorting to devices in image/* files.

For certain cases, this patch deviates from strict sorting, e.g.
to ensure that v10 comes after v9.

While at it, fix an indent and remove some useless empty lines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-21 22:17:39 +02:00
Hal Martin
3819c1638a sunxi: Add support for Banana Pi M2 Ultra
CPU: Allwinner R40 Quad-Core Cortex-A7 @ 1.2GHz
GPU: Mali 400 MP2
Memory: 2GB DDR3 onboard (shared with GPU)
Onboard: Storage microSD card slot
Onboard: Storage 8GB eMMC
Onboard: Network 10/100/1000M Ethernet RJ45
Onboard: Network WiFi 802.11b/g/n 1x1 (AMPAK AP6212; brcmfmac)
Onboard header: SPI, I2C, GPIO, UART
USB: Two USB 2.0 Host, One USB 2.0 OTG

Known issues:
- WiFi doesn't work
- eMMC not supported

Signed-off-by: Hal Martin <hal.martin@gmail.com>
2019-09-21 01:12:35 +02:00
Sandeep Sheriker M
89fe1dfac2 at91:sam9x: create sdcard images
create sdcard images for sam9x25 & sam9x35 ek targets.

Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
2019-09-21 01:09:27 +02:00
Sandeep Sheriker M
612e9ed7b8 at91:sama5: create fit image
create fit image & add it to sdcard image for sama5 target
device.

Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
2019-09-21 01:09:22 +02:00
Koen Vandeputte
c5b10c8282 kernel: bump 4.19 to 4.19.74
Refreshed all patches.

Fixes:
- CVE-2019-15504

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-20 15:51:49 +02:00
Koen Vandeputte
0b18fca82f kernel: bump 4.14 to 4.14.145
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-20 15:51:49 +02:00
Koen Vandeputte
c79cb9fda7 kernel: bump 4.19 to 4.19.73
Refreshed all patches.

Remove upstreamed:
- 840-media-i2c-tda1997x-select-V4L2_FWNODE.patch
- 079-v4.20-ARM-dts-qcom-ipq4019-fix-PCI-range.patch
- 083-ARM-dts-qcom-ipq4019-enlarge-PCIe-BAR-range.patch
- 084-ARM-dts-qcom-ipq4019-Fix-MSI-IRQ-type.patch

Fixes:
- CVE-2019-15030

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-20 13:16:17 +02:00
Koen Vandeputte
fb0c3eb5a3 kernel: bump 4.14 to 4.14.144
Refreshed all patches.

Altered patches:
- 816-pcie-support-layerscape.patch

Fixes:
-CVE-2019-15030

Compile-tested on: cns3xxx, layerscape
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-20 13:16:17 +02:00
Nick Briggs
3df3bb0dae ramips: add support for EnGenius ESR600
The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit
Ethernet switch, a gigabit Ethernet WAN port and a USB port.

Specification:

- Bootloader:	U-Boot
- SoC:		MediaTek MT7620A (600 MHz)
- Flash:	16MB, Macronix MX25L12845E
- RAM:		64MB, Nanya NT5TU32M16DG-AC
- Serial:	115200 baud, no header, 3.3V
  		J2: Vcc (arrow), Gnd, Tx, Rx
- USB:		USB 2, 5V
- Ethernet:	5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327
- WiFi0:	5 GHz 802.11 b/g/n Ralink RT5592N
  		300 Mb/s, 2T2R
- WiFi1:	2.4 GHz 802.11 b/g/n integrated
  		300 Mb/s, 2T2R
- Antennas:	2 per radio, internal
- LEDs:		1 programmable power (amber)
  		2 programable radio (blue)
		1 programable WPS-5G (blue)
		1 non-programable WAN activity (blue)
		1 unconfigured WPS-2.4G (amber)
- Buttons:	GPIO: Reset, WPS

Installation:

Use the OEM web interface to install the ...-factory.dlf image.
Use the OpenWRT ...-sysupgrade.bin image for future upgrades.

The J2 serial port can be accessed either by soldering in a header,
standard 0.1" spacing, or by using pogo-pins against the back side.

As configured by the OEM, the U-Boot boot delay is short, however quickly
typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP"
prompt.  The TFTP client is configured by default with
     client:   192.168.99.9
     server:   192.168.99.8
     filename: uImageESR600
It will load an OpenWRT initramfs kernel with this method.

Known issues:

1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational.
LAN1 and LAN2 do not appear to power up. This issue is also present
in the Lava LR25G001.

2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED,
is not configured in the Device Tree specification.

3) The blue WAN activity LED is not configured in the Device Tree
specification as this causes the AR8327 switch to fail to initialize.

Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com>
[merge conflict in 02_network]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-20 11:36:27 +02:00
Daniel Danzberger
10c5d3dd5f ramips: mt7621: Add new device AsiaRF AP7621-NV1
SoC:    Mediatek MT7621A
CPU:    4x 880Mhz
Cache:  32 KB I-Cache and 32 KB D-Cach
        256 KB L2 Cache (shared by Dual-Core)
RAM:    DDR3 512MB 16bits BUS
FLASH:  16MB
Switch: Mediatek Gigabit Switch (2 x LAN, 1 x WAN)
POE:    (1x PD, 2x PSE)
USB:    1x 3.0
PCI:    3x Mini PCIe (3 USB2.0 + 2 x UIM interface)
GPS:    Quectel L70B
SIM:    2 Slots
BTN:    Reset
LED:    - Power
        - Ethernet
        - Wifi
        - USB
UART:  UART is present as Pads with throughholes on the PCB.
       They are located on left side.
       3.3V - RX - GND - TX / 57600-8N1
       3.3V is the square pad

Installation
------------
The stock image is a modified openwrt and can be overflashed via sysupgrade -F

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
[merge conflict in mt7621.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-20 11:36:27 +02:00
Birger Koblitz
fde8e2e035 ramips: add support for Asus RT-AC85P
SoC:	MediaTek MT7621AT dual-core @ 880MHz
RAM:	256M (Winbond W632GG6KB-1)
FLASH:	128MB (Macronix MX30LF1G18AC-TI)
WiFi:	- 2.4GHz MediaTek MT7615N bgn
	- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB:	1 x USB 3.1 (Gen 1)
BTN:	Reset, WPS
LED:	- Power (blue)
	- 5Ghz (blue)
	- 2.4GHz (blue)
	- Internet (blue)
	- 4x LAN (blue)
	(LAN/WAN leds are not controllable by GPIOs)
UART: 	UART is present as Pads marked J4 on the PCB.
	3.3V - TX - RX - GND / 57600-8N1
	3.3V is the square pad
MAC:	The MAC address on the router-label matches the MAC of
	the 2.4 GHz WiFi.
	LAN and WAN MAC are identical: MAC_LABEL+4
	5 GHz WiFi MAC: also MAC_LABEL+4

Installation
------------
Via U-Boot tftpd:
Switch on device, within 2s press reset button and keep pressed
until power LED starts blinking slowly.
Upload factory image via tftp put, the router's ip is 192.168.1.1
and expects the client on 192.168.1.75.

The images also work on the Asus RT-AC65P models as tested by Gabor.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Tested-by: Gabor Varga <vargagab@gmail.com>
[fixed Asus -> ASUS in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-20 11:36:27 +02:00
Birger Koblitz
f285e8634c ramips: add support for Edimax RG21S
SoC:	MediaTek MT7621AT dual-core @ 880MHz
RAM:	256M (Nanya NT5CC128M)
FLASH:	16MB (Macronix MX25L12835F)
WiFi:	- 2.4GHz MediaTek MT7615N bgn
	- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB:	No
BTN:	Reset, WPS
LED:	4 red LEDs, indistinguishable when casing closed
UART: 	UART is present as Pads marked J1 on the PCB.
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation
------------
Update the factory image via the OEM web-interface
(by default:http://192.168.1.1)
The sysupgrade image can be installed via TFTP from
the U-Boot bootloader. Connect ethernet port 2.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[flash node rename, EDIMAX -> Edimax, complete device model name]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-20 11:36:27 +02:00
Álvaro Fernández Rojas
2e2fe82d1e brcm2708: fix Hifiberry DAC+DSP package definition
Fixes: ce536ae ("brcm2708: add support for Hifiberry DAC+DSP")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-09-20 07:50:47 +02:00
Fredrik Olofsson
dc76900021 kernel: Correctly search for the FIT image in mtd partition.
Previously all iterations of the loop checked offset=0 in the partition.

Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
2019-09-19 23:43:27 +02:00
Martin Schiller
315405f36b lantiq-dsl: fix value of FECS counter
Instead of the nFECS value, the nFEC value (the number of corrected code words)
was mistakenly used.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-09-19 23:43:27 +02:00
Roger Pueyo Centelles
6dda2ea6ad ath79: add SUPPORTED_DEVICES to ubnt_nanostation-m-xw
The ar71xx images for the Ubiquiti NanoStation M (XW) devices use
"nanostation-m-xw" as the board name, but the ath79 images are only
compatible with the "nano-m-xw" board name, so sysupgrade complains.

By adding this additional supported device, sysuspgrade smoothly
upgrades from ar71xx to ath79.

Tested on a NanoStation M (XW) running OpenWrt ar71xx r10250-016d1eb.

Ref: https://github.com/openwrt/openwrt/pull/2418
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[removed duplicate DEVICE_VARIANT, removed uneeded nano-m-xw support]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-19 23:43:27 +02:00
Adrian Schmutzler
425e0bd19a ath79: add XM device variant for Ubiquiti devices
So far, XW devices have DEVICE_VARIANT defined and XM devices have
no DEVICE_VARIANT set.

This adds DEVICE_VARIANT for XM devices, and moves definitions for
both XM and XW to the common definitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-19 23:43:27 +02:00
Adrian Schmutzler
7140394903 ramips: provide label MAC address
This patch adds the label MAC address for several devices in
ramips.

Some devices require setting the MAC address in 02_network:

For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- cudy,wr1000
- dlink,dir-615-d
- dlink,dir-615-h1
- dlink,dir-860l-b1
- glinet,gl-mt300a
- glinet,gl-mt300n
- glinet,gl-mt750
- vocore,vocore2
- vocore,vocore2-lite
- zbtlink,zbt-we1326
- zbtlink,zbt-wg3526

For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- dlink,dir-510l
- dlink,dwr-116-a1
- dlink,dwr-118-a1
- dlink,dwr-118-a2
- dlink,dwr-921-c1
- dlink,dwr-922-e2
- all hiwifi devices
- lava,lr-25g001
- xiaomi,mir3p

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-19 23:43:27 +02:00
Adrian Schmutzler
f8d9648529 ipq806x: provide label MAC address
This patch adds the label MAC address for several devices in
ipq806x.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-19 23:43:27 +02:00
Adrian Schmutzler
d0f800cfbd mpc85xx: provide label MAC address
This patch adds the label MAC address for some devices in
mpc85xx.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-19 23:43:27 +02:00
Adrian Schmutzler
50fdc0374b ath79: provide label MAC address
This patch adds the label MAC address for several devices in
ath79.

Some devices require setting the MAC address in 02_network:

For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- alfa-network,ap121f
- avm,fritz300e
- ubnt-xm devices

For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- adtran,bsap1800-v2
- adtran,bsap1840
- dlink,dir-842-c1/-c2/-c3
- engenius,ecb1750
- iodata,etg3-r
- iodata,wn-ac1167dgr
- iodata,wn-ac1600dgr
- iodata,wn-ac1600dgr2
- iodata,wn-ag300dgr
- nec,wg800hp
- nec,wg1200cr
- trendnet,tew-823dru

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-19 23:43:27 +02:00
Álvaro Fernández Rojas
ce536aeb39 brcm2708: add support for Hifiberry DAC+DSP
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-09-19 18:06:50 +02:00
Álvaro Fernández Rojas
39ddb25fbd brcm2708: add support for Raspberry Pi 2B 1.2
RPi 2B 1.2 has a BCM2710/BCM2837 like RPi 3 devices.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-09-19 17:38:18 +02:00
Álvaro Fernández Rojas
4f8b350be0 brcm2708: update to latest patches from RPi foundation
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-09-19 17:38:18 +02:00
DENG Qingfang
1979af10ca kernel: 4.19: fix crash when setting up spi-gpio
If an spi-gpio was specified with num-chipselects = <0> in dts, kernel
will crash:

 Unable to handle kernel paging request at virtual address 32697073
 pgd = (ptrval)
 [32697073] *pgd=00000000
 Internal error: Oops: 5 [# 1] SMP ARM
 Modules linked in:
 CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.19.72 #0
 Hardware name: Generic DT based system
 PC is at validate_desc+0x28/0x80
 LR is at gpiod_direction_output+0x14/0x128
 ...
 [<c0544db4>] (validate_desc) from [<c0545228>] (gpiod_direction_output+0x14/0x128)
 [<c0545228>] (gpiod_direction_output) from [<c05fa714>] (spi_gpio_setup+0x58/0x64)
 [<c05fa714>] (spi_gpio_setup) from [<c05f7258>] (spi_setup+0x12c/0x148)
 [<c05f7258>] (spi_setup) from [<c05f7330>] (spi_add_device+0xbc/0x12c)
 [<c05f7330>] (spi_add_device) from [<c05f7f74>] (spi_register_controller+0x838/0x924)
 [<c05f7f74>] (spi_register_controller) from [<c05fa494>] (spi_bitbang_start+0x108/0x120)
 [<c05fa494>] (spi_bitbang_start) from [<c05faa34>] (spi_gpio_probe+0x314/0x338)
 [<c05faa34>] (spi_gpio_probe) from [<c05a844c>] (platform_drv_probe+0x34/0x70)

The cause is spi_gpio_setup() did not check if the spi-gpio has
chipselect pins before setting their direction and results in derefing
an invalid pointer.

The bug is spotted in kernel 4.19.72 and does not occur in 4.14.

There is a similar fix upstream in kernel 5.2 in commit 249e2632dcd0
("spi: gpio: Don't request CS GPIO in DT use-case").

Ref: https://patchwork.kernel.org/patch/11150619/
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[use upstream patch, moved from hack to pending dir, commit facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-19 11:53:18 +02:00
Keith Maika
4cb5f29625 ath79: add support for TP-Link Archer C59v2
Add ath79 support for Archer C59v2, previously supported by ar71xx.

TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB

Flash instruction:
  - via web UI:
    1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
    2. Login to router and open the Advanced tab
    3. Navigate to System Tools -> Firmware Upgrade
    4. Upload firmware using the Manual Upgrade form
  - via TFTP:
    1. Set PC to fixed ip address 192.168.0.66
    2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
       and rename it to tp_recovery.bin
    3. Start a tftp server with the file tp_recovery.bin in its root directory
    4. Turn off the router
    5. Press and hold Reset button
    6. Turn on router with the reset button pressed and wait ~15 seconds
    7. Release the reset button and after a short time
       the firmware should be transferred from the tftp server
    8. Wait ~30 second to complete recovery.

Signed-off-by: Keith Maika <keithm@aoeex.com>
2019-09-16 21:40:06 +02:00
Adrian Schmutzler
38ccacf99b ath79: move common definitions from Archer C58/C59 to common DTSI
The Archer C58/C59 have redundant LED and MAC address definitions
in their DTS files. This moves them to the parent DTSI file.

The patch already accounts for the upcoming Archer C59 v2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-16 21:40:06 +02:00
Dan Haab
95240c4933 brcm47xx: sysupgrade: support Luxul firmware format
Allow flashing Luxul devices using vendor firmware format.

Signed-off-by: Dan Haab <dan.haab@legrand.com>
2019-09-16 21:37:33 +02:00
Dan Haab
bc5db7364d bcm53xx: sysupgrade: support Luxul firmware format
Allow flashing Luxul devices using vendor firmware format. The next step
will be building proper images once they are conirmed to work.

Signed-off-by: Dan Haab <dan.haab@legrand.com>
2019-09-16 16:01:42 +02:00
Rafał Miłecki
63d611390c ar71xx: fix typo in platform_do_upgrade_compex()
Fixes: 641f6b6c26 ("treewide: use new procd sysupgrade $UPGRADE_BACKUP variable")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-16 07:00:22 +02:00
Lorenzo Bianconi
14054e2982 mediatek: enable mtk_efuse by default
Enable by default mtk_efuse driver since it needed by mtk_thermal driver
to read sensor calibration data

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
2019-09-15 22:56:09 +02:00
Karl Palsson
dadcd3dd98 ath79: eg200: enable status led usage
This enables using the "eTactica" LED during boot, to indicate failsafe,
and during upgrade, while still leaving the LED alone for normal
operation.  This brings the device more in line with how other devices
work, and makes the failsafe functionality easier to use and understand.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2019-09-15 22:56:09 +02:00
Ivan Hörler
c03a328b10 ramips: add SD-Card support for Linkit Smart 7688
The Linkit Smart 7688 has a SD-Card reader that does not work with the official build of openwrt. Adding kmod-sdhci-mt7620 makes it working.

Signed-off-by: Ivan Hörler <i.hoerler@me.com>
2019-09-15 20:34:09 +02:00
Daniel Golle
6364e03736 ramips: only add spidev node in for WrtNode2R (and not for 2P)
Only the 2R version got the STM32 uC connected as 2nd SPI device.
Hence move the spidev node from mt7628an_wrtnode_wrtnode2.dtsi to
mt7628an_wrtnode_wrtnode2r.dts.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-09-15 20:18:39 +02:00
Yousong Zhou
a089d55170 apm821xx: image: remove unused kernel.dtb from IMAGES
It's a leftover from 2271967f ("apm821xx: utilize build ARTIFACTs")

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
2019-09-15 15:00:39 +00:00
Yousong Zhou
c163604b7f imx6: install-dtb as separate IMAGE
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2019-09-15 15:00:17 +00:00
Koen Vandeputte
1cf2495d48 ar71xx: make IRQ fixes target specific
Move the IRQ fix from generic to ar71xx specific.
Other targets like ath79 have specific pathes to delete this code.
This resulted in a build failure on ath79

While at it, wipe the 4.19 version, as ar71xx will never reach this.

Fixes: 530f76708cef ("ar71xx: Fix potentially missed IRQ handling during
dispatch")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-14 17:11:45 +02:00
Adrian Schmutzler
84c263ebfe brcm63xx: remove redundant variable definition in Makefile
For devices inheriting from bcm63xx_netgear, the IMAGES variable
is overwritten with the same values as defined in the parent
definition. So, remove the unnecessary overwrite.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-14 11:43:19 +02:00
Koen Vandeputte
713561a10b ar71xx: fix potential IRQ misses during dispatch for qca953x
If both interrupts are set in the current implementation
only the 1st will be handled and the 2nd will be skipped
due to the "if else" condition.

Fix this by using the same approach as done for QCA955x
just below it.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-13 16:40:29 +02:00
Koen Vandeputte
00d48bcac0 ar71xx: Fix potentially missed IRQ handling during dispatch
If both interrupts are set in the current implementation
only the 1st will be handled and the 2nd will be skipped
due to the "if else" condition.

Fix this by using the same approach as done for QCA955x
just below it.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-13 16:40:29 +02:00
Koen Vandeputte
78c3a18a1e kernel: bump 4.19 to 4.19.72
Refreshed all patches.

Remove upstreamed:
- 390-v5.3-net-sched-fix-action-ipt-crash.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-13 16:40:29 +02:00
Koen Vandeputte
6a4f4246fb kernel: bump 4.14 to 4.14.143
Refreshed all patches.

Remove upstreamed:
- 390-v5.3-net-sched-fix-action-ipt-crash.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-13 16:40:29 +02:00
Koen Vandeputte
7ea9c8dfbc kernel: bump 4.9 to 4.9.192
Refreshed all patches.

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-13 16:40:29 +02:00
David Bauer
18fa749df8 ath79: fix UniFi AC LED mapping
The UniFi AC LED mapping is currently off. The blue/white LED are used
as WiFi indicators, while the vendor firmware does not feature WiFI
LEDs.

Instead, the LEDs are used to indicate the devices status. Align the LED
mapping to match the vendor firmware as good as possible.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-12 15:39:21 +02:00
Koen Vandeputte
7489ea85a2 Revert "ar71xx: use platform code for qca955x usb0 init"
This reverts commit 5b98061bb1.

As Piotr Dymacz pointed out:

In QCA MIPS based WiSOCs, for first USB interface,
device/host mode can be selected _only_ in hardware
see description of 57c641ba6e

QCA955x and QCA9563, second USB can be switched to device
mode in software (tested and confirmed on real hardware).

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-12 00:15:59 +02:00
Moritz Warning
c546855188
imx6: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-11 15:19:54 +02:00
Moritz Warning
bdf0ca7fec samsung: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-11 15:17:09 +02:00
Tomislav Požega
191c3e49b9 ar71xx: qca955x pci init/reset fixes
Current ar724x code does the reset only on single pci bus, and
in case of qca9558 writes the wrong register (0x10 vs 0x0c).
This change allows the reset of second pci bus, commonly used in
Archer C7 devices, in case host controller is stuck in reset.
If the resetting controller on boot can solve any other issue it
can be enabled unconditionally by removing reset check before
ar724x_pci_hw_init is called.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
[refreshed to apply cleanly]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-11 09:47:49 +02:00
Tomislav Požega
e8350c998b ar71xx: enable ddr wb flush on qca955x
Enable flushing of write buffers on qca955x. GPL code has 0x88 reg
defined for PCI flush which is likely an error since the device
freezes on boot. So use DS default value 0xA8 for PCI flush.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
2019-09-11 09:47:49 +02:00
Tomislav Požega
5b98061bb1 ar71xx: use platform code for qca955x usb0 init
Switch from ci_usb_setup to generic platform initialization of
usb0 port.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
2019-09-11 09:47:49 +02:00
Koen Vandeputte
1d51160f85 kernel: bump 4.19 to 4.19.71
Refreshed all patches.

Remove upstreamed:
- 950-0774-watchdog-bcm2835_wdt-Fix-module-autoload.patch
- 0017-usb-host-fotg2-restart-hcd-after-port-reset.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-11 09:47:49 +02:00
Koen Vandeputte
6999c7e28e kernel: bump 4.14 to 4.14.142
Refreshed all patches.

Remove upstreamed:
- 0032-usb-host-fotg2-restart-hcd-after-port-reset.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-11 09:47:49 +02:00
Koen Vandeputte
3b6b66529f kernel: bump 4.9 to 4.9.191
Refreshed all patches.

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-09-11 09:47:49 +02:00
Rafał Miłecki
a858db3136 treewide: sysupgrade: use $UPGRADE_BACKUP to check for backup
Now that $UPGRADE_BACKUP is set conditionally there is no need to check
the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-11 09:05:35 +02:00
Yousong Zhou
6d819fae53 gemini: image: fix race condition when building copy-kernel.bin
Make treat copy-kernel.o as intermediate and delete it when it's no
longer needed.  This can fail when the same submake was triggered
multiple times for different devices.

	arm-openwrt-linux-muslgnueabi-as  -k -o copy-kernel.o copy-kernel.S
	export MAKEFLAGS= ;make -w -C copy-kernel CROSS_COMPILE=arm-openwrt-linux-muslgnueabi-
	arm-openwrt-linux-muslgnueabi-objcopy -O binary -S copy-kernel.o copy-kernel.bin
	make[5]: Entering directory '/builder/shared-workdir/build/target/linux/gemini/image/copy-kernel'
	arm-openwrt-linux-muslgnueabi-objcopy -O binary -S copy-kernel.o copy-kernel.bin
	rm copy-kernel.o
	make[5]: Leaving directory '/builder/shared-workdir/build/target/linux/gemini/image/copy-kernel'
	# "App" partition is the rootfs
	arm-openwrt-linux-muslgnueabi-objcopy: 'copy-kernel.o': No such file
	Makefile:27: recipe for target 'copy-kernel.bin' failed
	make[5]: Leaving directory '/builder/shared-workdir/build/target/linux/gemini/image/copy-kernel'
	make[5]: *** [copy-kernel.bin] Error 1
	Makefile:244: recipe for target '/builder/shared-workdir/build/build_dir/target-arm_fa526_musl_eabi/linux-gemini/tmp/openwrt-gemini-storlink_sl93512r-ext4-factory.bin' failed
	make[4]: *** [/builder/shared-workdir/build/build_dir/target-arm_fa526_musl_eabi/linux-gemini/tmp/openwrt-gemini-storlink_sl93512r-ext4-factory.bin] Error 2

With this change, output files are directed to $(KDIR)

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2019-09-11 01:31:53 +00:00
Roger Pueyo Centelles
e667d6f46b ramips: enable external amplifier for D-Link DIR-810L
The 2.4 GHz radio had very poor signal reception (-89 dBm for an AP
sitting 5 m away). By enabling the external amplifier, received signal
has improved to -50 dBm for the same AP.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-09-10 22:43:37 +08:00
Adrian Schmutzler
869a0183b9 ramips: fix MAC address setup for Newifi Y1 and Y1S
So far, MAC address setup for those devices has been using local
addresses although additional MAC addresses are available on flash.

On device, we found the following situation:
position   Y1     Y1S
0x4        *:d4   *:e4
0x8004     *:d6   *:e8
0x28       *:d4   *:e4
0x2e       *:d7   *:eb

Since 0x4 and 0x28 yield the same address, the former was set for
&ethernet in DTS. However, the typical location on this
architecture is 0x28, so this patch changes that.

For further setup in 02_network, the local bit for lan_mac is
removed, so the address from &ethernet is used at all. For wan_mac,
instead of calculating an address with local bit set, this patch
exploits the previously unused address in 0x2e.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-07 21:41:44 +08:00
Adrian Schmutzler
aaf90d8808 ramips: initialize MAC addresses from flash where possible
This patch changes wan MAC address setup from retrieving it by
calculation to reading it from flash.

Changes are limited to cases where on-device check was possible.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[fix mac for newifi-d1; drop adslr,g7 because it's unlikely for
vendor to specifically use 2.4g mac as wan_mac]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-09-07 21:41:44 +08:00
Adrian Schmutzler
e35e4a996e ramips: fix duplicate network setup for dlink,dir-615-h1
In 555ca422d1 ("ramips: fix D-Link DIR-615 H1 switch port
mapping"), port setup for dir-615-h1 was changed without removing
the old one. This was working as the new one was triggered earlier
than the old one.

(In the meantine, changed sorting during ramips rename patches
actually inversed that order.)

Anyway, just remove the wrong case now.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-07 21:41:44 +08:00
Adrian Schmutzler
ad4eb2241b ramips: remove duplicate case for MAC setup of freestation5
ARC FreeStation5 is present twice in MAC address setup.

From older commits/changes, it is not possible to reconstruct
the correct choice only by reading the annotations.

Thus, remove the second case and keep the first one, so behavior
stays the same (as nobody seems to have complained about it).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-07 21:41:44 +08:00
Adrian Schmutzler
6640e1c368 ramips: clean and improve MAC address setup in 02_network
This patch removes unnecessary MAC address setup statements in
ramips' 02_network by doing several optimizations:

1. For the following devices, lan_mac was set up with
   mtd_get_mac_binary although the same address was set in DTS.
   The lan_mac statement is removed in 02_network, but
   wan_mac is kept:
   - mercury,mac1200r-v2
   - phicomm,k2g
   - skylab,skw92a
   - wiznet,wizfi630a

2. For the following devices, wan_mac was set up with
   mtd_get_mac_binary although the same address was set in DTS.
   The wan_mac statement is removed in 02_network, no
   lan_mac is present:
   - buffalo,whr-g300n
   - glinet,gl-mt300n-v2
   - zyxel,keenetic-start

3. For the following device, lan_mac and wan_mac were set up
   with mtd_get_mac_binary to the same address as set in DTS.
   Both statements are removed in 02_network:
   - buffalo,whr-600d

4. For some devices, it was possible to move setup from 02_network
   to DTS by introducing previously missing mtd_mac_address:
   - buffalo,whr-1166d
   - buffalo,whr-300hp2
   - buffalo,wsr-600dhp
   - ohyeah,oy-0001
   - planex,vr500

5. For one device, mtd_mac_address was just wrong and overwritten
   by 02_network. Put the correct value in DTS and remove redundant
   statement in 02_network:
   - asus,rt-ac57u

6. For one device, MAC address defined in DTS is exchanged together
   with lan_mac/wan_mac setup in 02_network, so that cases in
   02_network can be merged:
   - phicomm,k2p

For some devices, an empty case has to be used to prevent them
from falling into the default case and have
WAN address = eth0 address + 1 set to them.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-07 21:41:44 +08:00
Rafał Miłecki
c19b9f9a26 bcm53xx: extend firmware validation
This provides TRX validation result to the validation JSON. It also
prevents users from installing broken firmware files.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-06 12:52:59 +02:00
Rafał Miłecki
641f6b6c26 treewide: use new procd sysupgrade $UPGRADE_BACKUP variable
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.

This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-05 23:33:19 +02:00
Rafał Miłecki
62dbe361a1 treewide: when copying a backup file always specify dest name
$CONF_TAR shouldn't be assumed to always point to the sysupgrade.tgz.
This change makes code more generic and allows refactoring $CONF_TAR.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-05 14:33:20 +02:00
Rafał Miłecki
bf39047872 treewide: don't hardcode "sysupgrade.tgz" file name
1) Add BACKUP_FILE and use it when copying an archive to be restored
   after sysupgrade (on the next preinit).
2) Use CONF_TAR for copying backup prepared by the /sbin/sysupgrade

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-05 14:33:19 +02:00
Rafał Miłecki
1078de96e3 treewide: fix invalid UPGRADE_OPT_SAVE_CONFIG spellings
That was a result of accidentally running "sed" twice on some files.

Fixes: 5797fe84a3 ("treewide: replace remaining (not working now) $SAVE_CONFIG uses")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-05 08:55:15 +02:00
Rafał Miłecki
5797fe84a3 treewide: replace remaining (not working now) $SAVE_CONFIG uses
This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG

Fixes: b534ba9611 ("base-files: pass "save_config" option to the "sysupgrade" method")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-05 08:43:24 +02:00
Álvaro Fernández Rojas
662394fb30 brcm2708: update to latest patches from RPi foundation
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-09-04 19:02:48 +02:00
Álvaro Fernández Rojas
99a5e28588 brcm2708: bcm2711: remove custom config file
Forcing arm_64bit is no longer required with latest firmware.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-09-04 18:11:25 +02:00
Chuanhong Guo
7a21c85f70 ramips: improve support for Xiaomi Miwifi Nano
This patch does the following things:
1. mark u-boot-env writable
2. add bootcount support
   Currently, u-boot has a flag_boot_success env variable to reset.
   Also reset it in our firmware to follow the behavior in vendor's
   firmware.
3. disable usb support
   This router doesn't have usb port at all.
4. increase spi clock to 40MHz
5. fix pinmux groups

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-09-04 19:26:01 +08:00
Rafał Miłecki
e68c1cebd1 brcm47xx: extend firmware validation
This provides TRX validation result, so final JSON may look like:
{
	"tests": {
		"fwtool_signature": true,
		"fwtool_device_match": true,
		"trx_valid": true
	},
	"valid": true,
	"forceable": true
}

It also prevents users from installing broken firmware files, e.g.:

root@OpenWrt:/# sysupgrade -F -n /tmp/TZ
Image metadata not found
Invalid image type. Please use firmware specific for this device.
Image check failed but --force given - will update anyway!
Commencing upgrade. Closing all shell sessions.
Firmware image is broken and cannot be installed

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-04 06:37:17 +02:00
Álvaro Fernández Rojas
5287ac2dfb brcm2708: restore UART on RPi 0W, 3B, 3B+ and 4B
Disable Bluetooth and restore UART to GPIOs 14 & 15.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-09-03 19:37:29 +02:00
Adrian Schmutzler
fbbb4eb8b4 ath79: add support for TP-Link WDR3500 v1
Hardware:
SoC:      AR9344
CPU:      560 MHz
Flash:    8 MiB
RAM:      128 MiB
WiFi:     Atheros AR9340 2.4GHz 802.11bgn
          Atheros AR9300 5GHz 802.11an
Ethernet: AR934X built-in switch, WAN on separate physical interface
USB:      1x 2.0

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
   wdr3500v1_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[removed stray newline]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-03 18:43:27 +02:00
Jo-Philipp Wich
efaaadb49e sdk: use bundle-libraries.sh to ship kernel objtool tools
Ensure that the kernel objtool utilities are processed by the library
bundler in order to ensure that they're usable on foreign systems with
different libc versions.

Fixes: a9f6fceb42 ("sdk: fix building external modules when CONFIG_STACK_VALIDATION=y")
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-09-03 10:45:25 +02:00
Paul Spooren
ac418ddecc bcm53xx: add generic subtarget
Same game as for 853e4dd306. Add generic
to the filenames.

CC: Hauke Mehrtens <hauke@hauke-m.de>

Signed-off-by: Paul Spooren <mail@aparcar.org>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
2019-09-02 22:38:47 +02:00
DENG Qingfang
26851f9db2 mvebu: fix Linksys WRT LAN/WAN MAC addresses
According to 02_network, eth0.1 is LAN and eth1.2 is WAN,
but $mac_wan was assigned incorrectly to eth0 in preinit.

Swap eth0 and eth1 to fix this.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-09-01 18:38:04 +02:00
Cong Wang
7735cce0c5 kernel: net_sched: fix a NULL pointer deref in ipt action
The net pointer in struct xt_tgdtor_param is not explicitly
initialized therefore is still NULL when dereferencing it.
So we have to find a way to pass the correct net pointer to
ipt_destroy_target().

The best way I find is just saving the net pointer inside the per
netns struct tcf_idrinfo, which could make this patch smaller.

Fixes: 0c66dc1ea3f0 ("netfilter: conntrack: register hooks in netns when needed by ruleset")
Reported-and-tested-by: Tony Ambardar <itugrok@xxxxxxxxx>
Cc: Jamal Hadi Salim <jhs@xxxxxxxxxxxx>
Cc: Jiri Pirko <jiri@xxxxxxxxxxx>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>

[Backport for kernel v4.19 and v4.14]
[Bug Link: https://bugzilla.kernel.org/show_bug.cgi?id=204681]
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2019-09-01 18:38:04 +02:00
Tomasz Maciej Nowak
0cc87b3bac ath79: image: disable sysupgrade images for routerstations and ja76pf2
Because a bug in handling partial erase blocks in 4.19 kernel, using
sysupgrade images will hard brick devices that use RedBoot bootloader
and have "FIS directory" with "RedBoot config" on the same erase block.
Since flashing the devices from bootloader is safe, and to not cause a
situation where external chip programmer or JTAG is needed, disable
sysupgrade images for affected boards while creating kernel.bin and
rootfs.bin for jjPlus JA76PF2 board, which doesn't have factory image.

To set up the JA76PF2 board follow "Installation" instructions in b3a0c97
("ath79: add support for jjPlus JA76PF2") except the part of loading
initramfs image and using sysupgrade image for flashing (point 6 and 7).
Enter following commands to flash the board from bootloader:
  fis init
  load -r -b 0x80060000 <openwrt_kernel_image_name>
  fis create linux
  load -r -b %{FREEMEMLO} <openwrt_rootfs_image_name>
  fis create rootfs
  fis load -l linux
  exec -c ""

For RouterStations use TFTP recovery procedure.

Ref: FS#2428
Cc: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-09-01 00:12:03 +02:00
Tomasz Maciej Nowak
0bf6a531c2 ath79: fix FIS partition detection for 4.19 kernel
When bumping to 4.19 the patch responsible for scaning flash for FIS
partition got left out. Without it devices with RedBoot bootloader using
automatic partitions detection in dts won't boot with the new kernel.

Fixes: 3771176 ("ath79: add support for linux 4.19")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-09-01 00:12:03 +02:00
Tomasz Maciej Nowak
a45cf75eca ath79: image: add supported string for routerstations and ja76pf2
Now that the md5 check is fixed and metadata present, sysupgrade on
ar71xx will complain about device not being supported by the image.
Since the cause is not matching strings for supported devices add them
accordingly.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-09-01 00:12:02 +02:00
Tomasz Maciej Nowak
077d06a1a5 ath79: image: append metadata to routerstations and ja76pf2 images
This target enforces metadata check so add the necessary information. It
was previously removed because md5 sum check. When using these sysupgrade
images on ar71xx target the check would complain about them not matching.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-09-01 00:12:02 +02:00
Tomasz Maciej Nowak
8b4109c2b4 ar71xx: sysupgrade: accept ath79 combined-image
There is md5 sum of whole image embedded in combined-image header which
is checked on sysupgrade. The check will fail for ath79 images which
may have embedded metadata. This is because metadata are appended after
the combined image is created. To allow smooth transition from ar71xx to
ath79, strip metadata before calculating md5 sum for whole image.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-09-01 00:12:02 +02:00
Tomasz Maciej Nowak
900330ff2f ath79: image: retire combined-image for Adtran/Bluesocket devices
During review it slipped by that these devices use combined-image which
should never be used for newly added ones. Therefore switch to
sysupgrade-tar generated images introduced in 8f6f260 ("ath79:
routerstation: prepare to use sysupgrade-tar format image"). The
sysupgrade accepts both images for now so no reression should occur.

Cc: Brian Gonyer <bgonyer@gmail.com>
Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-09-01 00:12:02 +02:00
Tomasz Maciej Nowak
c1db564cbc ath79: dts: fix ja76pf2 spi frequency
The frequency was filled acording the information from datasheet for
particular chip (Winbond 25Q128BVFG). Unfortunately this led to
coruption and introduced bad blocks on the chip. Reducing the frequency
to commonly used in ath79, made the board more stable and no new bad
blocks were spoted.

Fixes: b3a0c97 ("ath79: add support for jjPlus JA76PF2")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-09-01 00:12:02 +02:00
David Bauer
7b137e9df9 ath79: correct OCEDO Ursus phy-mode property
This fixes the previously incorrect phy-mode for the OCEDO Ursus GMAC0.

See 62abbd587d ("ath79: correct various phy-mode properties")
for more details.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 22:11:29 +02:00
Adrian Schmutzler
d94a3f328f ipq806x: Replace backticks by $(...)
This replaces deprecated backticks by more versatile $(...) syntax.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-31 12:08:23 +02:00
Michal Cieslakiewicz
dddb43775f ar71xx: WNR2200: remove redundant GPIO for WLAN LED
Without this patch, an extra entry appears for AR9287 GPIO
that duplicates WLAN LED but in fact drives nothing:

gpiochip1: GPIOs 502-511, ath9k-phy0:
 gpio-502 (                    |netgear:blue:wlan   ) out hi
 gpio-503 (                    |netgear:amber:test  ) out hi
 gpio-504 (                    |netgear:green:power ) out lo
 gpio-505 (                    |rfkill              ) in  hi
 gpio-507 (                    |wps                 ) in  hi
 gpio-508 (                    |reset               ) in  hi
 gpio-510 (                    |ath9k-phy0          ) out hi <===!

The pin pointed above is default LED GPIO (8) for AR9287.
For WNR2200 it is not connected anywhere - pin 0 drives blue WLAN
LED instead - but initialization code is missing that information.

This fix calls ap9x_pci_setup_wmac_led_pin() function at device
setup, forcing WLAN LED pin to be 0 and removing redundant entry.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-08-31 12:08:23 +02:00
Karl Pálsson
075c570cde ath79: etactica-eg200: fix restore button
The button is labelled reboot/restore in documentation, and has always
been used for that.  Naming it WPS has always been wrong.

Signed-off-by: Karl Pálsson <karlp@etactica.com>
[matched author to SoB]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-08-31 12:08:23 +02:00
Christoph Krapp
6cea9688af ramips: add support for Netgear R6260 and R6850
As Netgear uses the same image for R6260, R6350 & R6850
we can merge device tree files and generate separate
images for each device.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[add missing WiFi compatible string, fix network
configuration]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 10:31:00 +02:00
Christoph Krapp
3c8df280a9 ramips: add factory image for Netgear R6350
This adds factory image generation for all three
devices. These images can be flashed via WebUI
for easy installation.

Thanks to David Bauer for the inspiration.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[altered commit to only include the R6350]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 10:31:00 +02:00
Christoph Krapp
9861fa7aba ramips: add mt7615e support to Netgear R6350
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2019-08-31 10:31:00 +02:00
David Bauer
13937a16d4 ramips: fix network setup for various NETGEAR boards
There are currently the following issues present for the Netgear R6220,
R6350 and WNDR3700 v5:

 - LAN and WAN MAC-addresses are inverted
 - WAN MAC-address is off. It are +2 compared to the LAN MAC-address
   (R6350 only)
 - Switchport order is inverted in LuCi

This commit fixes both these issues by assigning correct MAC-addresses
to LAN and WAN interfaces and defining the switchports with the correct
labels.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 10:31:00 +02:00
David Bauer
fa46c9b208 ramips: use phy trigger for various Netgear boards
This commit switches the default trigger for the WiFi LED from a netdev
trigger on "wlan0" to a wireless-phy based trigger. THis allows the LED
to work, even when the wireless interface is not named "wlan0" without
modifiying the LED settings.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 10:31:00 +02:00
David Bauer
607dfdf211 ramips: add factory image for NETGEAR R6220
This adds an easy-installation factory image for the NETGEAR R6220
router. The factory image can either be flashed via the vendor Web-UI or
the bootloader using nmrpflash.

Tested with NETGEAR V1.1.0.86 firmware.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 10:31:00 +02:00
David Bauer
527832e54b ramips: disable badblock shifting for MT7621 NAND
The MediaTek MT7621 NAND driver currently intransparently shifts NAND
pages when a block is marked as bad. Because of this, offsets for e.g.
caldata and MAC-addresses seem to be off.

This is, howeer, not a task for the mtd NAND driver, as the flash
translation layer is tasked with this.

This patch disables this badblock shifting. This fix was originally
proposed by Jo-Philipp Wich at
https://bugs.openwrt.org/index.php?do=details&task_id=1926

Fixes FS#1926 ("MTD partition offset not correctly mapped when bad
eraseblocks present")
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 10:31:00 +02:00
Koen Vandeputte
db97cb814c kernel: bump 4.19 to 4.19.69
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-30 16:45:54 +02:00
Koen Vandeputte
071209ed22 kernel: bump 4.14 to 4.14.141
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-30 16:45:54 +02:00
John Crispin
7f9edadf85 mediatek: backport a pcie fix
PCI/e probe was failing under certain situations.

Signed-off-by: John Crispin <john@phrozen.org>
2019-08-30 07:28:47 +02:00
Vladimir Vid
bec2df9a66 mvebu: sysupgrade: fix uDPU eMMC check regression
Add udpu_ prefix in all other function names

Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
2019-08-29 20:53:32 +02:00
Álvaro Fernández Rojas
055abe902b brcm2708: remove duplicated patch
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-08-29 16:19:00 +02:00
Etienne Champetier
7d542dc804 kernel: add disable_eap_hack sysfs attribute
We are not sure if 640-bridge-only-accept-EAP-locally.patch is still needed
as a first step, add disable_eap_hack sysfs config to allow to disable it

Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
2019-08-28 16:10:45 +02:00
John Crispin
4685fc0cf1 mediatek: update v4.19 switch support to latest vendor version
Signed-off-by: John Crispin <john@phrozen.org>
2019-08-28 15:20:22 +02:00
Koen Vandeputte
1bc31e0339 kernel: bump 4.19 to 4.19.68
Refreshed all patches.

Remove upstreamed:
- 950-0307-Revert-pwm-Set-class-for-exported-channels-in-sysfs.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-28 13:08:20 +02:00
Koen Vandeputte
b5407887bc kernel: bump 4.14 to 4.14.140
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-28 13:08:20 +02:00
Koen Vandeputte
b32c77004c kernel: bump 4.9 to 4.9.190
Refreshed all patches.

Fixes:
- CVE-2019-3900

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-28 13:08:20 +02:00
Álvaro Fernández Rojas
2876709fb7 brcm2708: fix DMA leaks in bcm2835-mmc
Add patches from https://github.com/raspberrypi/linux/pull/3164

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-08-27 15:19:26 +02:00
Álvaro Fernández Rojas
2340c646e6 brcm2708: update to latest patches from RPi foundation
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-08-27 11:10:01 +02:00
Koen Vandeputte
81d0da1186 ar71xx/ath79: ag71xx: dont fetch the same var again
tx_size was just declared above and set to BIT(tx->order)
Use the declaration instead, which could avoid a pointer deref

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
e773838813 ar71xx: ag71xx: use base address value directly from the source
This brings the code more inline with the ath79 flavour

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
19ed799bdc ar71xx: ag71xx: make use of managed dev API simplifying code
Backport of a4eef43a12 ("ath79: ag71xx: replace alloc_etherdev with devm_alloc_etherdev")
combined with the initial changes from John Crispin.

Simplifies the code a lot by using the Managed dev API.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
4d40c0edd4 ar71xx: ag71xx: replace ag71xx_get_phy_if_mode_name with phy_modes()
Backport of f73b2d64ed ("ath79: ag71xx: replace ag71xx_get_phy_if_mode_name() with phy_modes()")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
e18724b907 ar71xx: ag71xx: pass correct device pointer to dma
Backport of 4eaa3626a8 ("ath79: ag71xx: pass correct device pointer to dma functions")

While 4.14 does not contain the warnings,
it still makes sense to use the proper pointers here.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
662922068d ar71xx/ath79: ag71xx: get ring_mask consistent
All other instances of this identical declaration fetch the
value directly from the ring_order.

Also do it here.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
e10b163247 ar71xx: ag71xx: add missing register writes
These are added in ath79, but were not backported here

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
491eaa898b kernel: bump 4.19 to 4.19.67
Refreshed all patches.

Also add a missing symbol for x86 which got used now in this bump.
- ISCSI_IBFT

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
5f013de786 kernel: bump 4.14 to 4.14.139
Refreshed all patches.

Also add a missing symbol for x86 which got used now in this bump.
- ISCSI_IBFT

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Felix Fietkau
c3a78955f3 kernel: move crypto-arc4 into a module
It is no longer required by wireless drivers, so we can save some space here

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-08-26 18:21:13 +02:00
Christian Lamparter
94bf2e4813 ipq40xx: drop unreachable ipq-wifi package for the AP120C-AC
Harri Hursti reported that ALFA Network AP120C-AC does not
work anymore due to: "Unknown package 'ipq-wifi-alfa-network_ap120c-ac'."

This patch fixes the issue by removing the stale package from
the device's dependencies as the calibration data is now
provided by the upstream board-2.bin.

Reported-by: Harri Hursti <harri@nordicinnovationlabs.com>
Fixes: 8f757d427c ("ipq-wifi: drop upstreamed custom board-2.bin")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-08-24 23:23:31 +02:00
Christian Lamparter
3dc5716b07 ramips: add NAS goodies on U25AWF-H1 + U35[N|W]F
These devices are sold as a "NAS HDD Enclousure"
and have a "NAS Media Streaming & File Server & AP" on
the box. That's why I think they should have some support
for the HDD right out-of-the-box.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-08-24 23:23:31 +02:00
Luka Perkov
f4500fde1e kernel: refresh patches
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
2019-08-24 23:11:15 +02:00
Vladimir Vid
7dff6a8c89 mvebu: uDPU: add sysupgrade support
This patch adds sysupgrade, uboot-env and networking support
for Methode uDPU device.

Device features 4 partitions:

-----------------------------------------
|  boot   | recovery  | rootfs |  misc  |
| (ext4)  |  (ext4)   | (fsf2) | (f2fs) |
_________________________________________

Idea was to use f2fs only but the u-boot currently lacks support
so first 2 partition are ext4 to be u-boot readable, and this was
a reason why custom build and sysupgrade sections were required.

On the sysupgrade, boot and rootfs partitions are updated, firmare
image and user configuration is saved on the misc partition and if
the upgrade was successfull, recovery partition will be updated on
after the reboot from preinit script. If the sysupgrade fails for any
reason, device will fallback to recovery initramfs image.

Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
2019-08-24 23:11:15 +02:00
Vladimir Vid
b8474dc42b kernel: 4.19: backport mx25u12835f support from linux 5.0
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
2019-08-24 23:11:15 +02:00
Luochongjun
921675a2d1 ath79: add support for gl-ar750
This patch supports gl-ar750, which was previously supported by ar71xx.

Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 2xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Switch: 1x switch
- Button: 1x reset button
- LED: 3x LEDS (white)

Flash instruction:
Support for sysupgrade directive upgrades, as well as luci upgrades.

Signed-off-by: Luochongjun <luochongjun@gl-inet.com>
2019-08-24 08:55:33 +08:00
Zhenjian Zhang
fb3574f123 ramips: add support for ADSLR G7
SoC: MT7621AT
RAM: 256MB
Flash: 16M SPI
Ethernet: 5x GE ports
WiFi: 2.4G: MT7615N
5G: MT7615N

Flash instruction:
1.Modify the file to linux.bin
2.Set up FTP service
3.Computer settings fixed IP: 192.168.179.50 255.255.255.0
4.Turn on the power and press and hold the reset button until the indicator light is on for about 5 seconds.

Signed-off-by: Zhenjian Zhang <itdesk.zhang@gmail.com>
[fix mac location]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-08-24 08:55:33 +08:00
Paul Spooren
853e4dd306 ipqx0xx: add Generic subtarget
Both targets miss a subtarget causing an image naming style which is
different from other all othe targets, even tho it already uses
`x/generic/` as subfolder as if the subtarget would exist.

This commit adds the Generic subtarget resulting in consistent naming.

    ~/src/openwrt/openwrt/bin/targets/ipq806x/generic$ ls
    openwrt-ipq806x-generic-netgear_d7800-initramfs-uImage
    openwrt-ipq806x-generic-netgear-d7800.manifest
    openwrt-ipq806x-generic-netgear_d7800-squashfs-factory.img
    openwrt-ipq806x-generic-netgear_d7800-squashfs-sysupgrade.bin

CC: John Crispin <john@phrozen.org>

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-08-22 21:15:28 +02:00
Daniel Golle
ccf3bac6f3 lantiq: add device alias for Alpha ASL56026
BT Openreach ECI VDSL Modem V-2FUb/I is an alias of Alpha ASL56026 as
also stated in the original commit message adding the device
(commit 6254a2028c "lantiq: add support for the Alpha ASL56026").

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-08-22 16:26:05 +02:00
Adrian Schmutzler
0fcab46f97 lantiq: sort device definitions in image/Makefile
This sorts the device definitions in image/Makefile alphabetically
for each subtarget/block.

The order of blocks has not been touched.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 16:26:05 +02:00
Rafał Miłecki
b6f4cd57e1 treewide: sysupgrade: pass "save_partitions" option to the "sysupgrade" method
This explicitly lets stage2 know if partitions should be preserved. No
more "touch /tmp/sysupgrade.always.overwrite.bootdisk.partmap" hack.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-08-22 13:47:51 +02:00
Daniel Golle
41f580b596 ramips: add device alias for Allnet ALL0239-3G
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-08-22 13:22:39 +02:00
Paul Spooren
149d1e7a61 ramips/mt76x8: add DEVICE_VENDOR for tl-wr840n-v5
DEVICE_VENDOR is missing for this device.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-08-22 12:57:34 +02:00
Moritz Warning
fd66687058 lantiq: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Uses DEVICE_ALT* variables for alternative vendor/retailer names.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-08-22 12:57:34 +02:00
Christian Lamparter
8f757d427c ipq-wifi: drop upstreamed custom board-2.bin
The BDFs for the:
	ALFA Network AP120C-AC
	ASUS Lyra
	AVM FRITZ!Box 7530
	AVM FRITZ!Repeater 3000
	EnGenius EAP1300
	EnGenius ENS620EXT
	Netgear Orbi Pro SRK60

boards were upstreamed to the ath10k-firmware repository
and linux-firmware.git.

Furthermore the BDFs for the:
	OpenMesh A42 specific BDFs
	OpenMesh A62 specific BDFs
	Linksys EA6350v3
have been updated.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-08-18 20:56:41 +02:00
Deng Qingfang
fd4804ce33 ramips: add MT7530 switch port-mirroring support
Compile & run tested on MT7620, MT7621

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
[Tested on Phicomm PSG1218 rev.A, MediaTek MT7620A ver:2 eco:6]
Tested-by: MingHao Chen <cmheia@email.com>
2019-08-18 22:08:42 +08:00
Sandeep Sheriker M
552c48ea43 at91/image/sama5.mk: check for sama5d4_xplained device
check for sama5d4_xplained device while copying at91bootstrap binary
to sdcard image.

Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
2019-08-17 23:09:04 +02:00
Sandeep Sheriker M
05a81abb5f at91: remove Build/at91-sdcard command
remove at91-sdcard build command from Makefile as this is moved to
respective subtarget Makefile.

Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
2019-08-17 23:08:59 +02:00