mac80211_get_addr is called from mac80211_generate_mac, where the local variable
initialisation id="${macidx:-0}" suggests that macidx is not always defined.
Probably, idx was supposed to be used instead of $(($macidx + 1)).
Fixes: 4d99db168c ("mac80211: try to get interface addresses from wiphy sysfs 'addresses' if no mask is set")
Signed-off-by: Leon M. George <leon@georgemail.eu>
(cherry picked from commit 8f95220bcb)
The JSON `WORK_DIR` ($(KDIR)/json_info_files) is only created if the new
image generation methods from `image.mk` are used. However some targets
like `armvirt` do not use it yet, so the folder is never created.
The `json_overview_image_info.py` script used to raise an error if the
given `WORK_DIR` isn't a folder, however it should just notify about
missing JSON files.
This patch removes the Python assert and exists with code 0 even if no
JSON files were found, as this is not necessarily an error but simply
not yet implemented. Using `glob` on an not existing `Path` results in
an empty list, therefore the for loop won't run.
Signed-off-by: Paul Spooren <mail@aparcar.org>
CC: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 14cbd8fb2d)
JSON info files contain machine readable information of built profiles
and resulting images. These files were added in commit 881ed09ee6
("build: create JSON files containing image info").
They are useful for firmware wizards and script checking for
reproducibility.
Currently all JSON files are stored next to the built images, resulting
in up to 168 individual files for the ath79/generic target.
This patch refactors the JSON creation to store individual per image
(not per profile) files in $(BUILD_DIR)/json_info_files and create an
single overview file called `profiles.json` in the target directory.
Storing per image files and not per profile solves the problem of
parallel file writes. If a profiles sysupgrade and factory image are
finished at the same time both processes would write to the same JSON
file, resulting in randomly broken outputs.
Some target like x86/64 do not use the image code yet, resulting in
missing JSON files. If no JSON info files were created, no
`profiles.json` files is created as it would be empty anyway.
As before, this creation is enabled by default only if `BUILDBOT` is set.
Tested via buildroot & ImageBuilder on ath79/generic, imx6 and x86/64.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[json_info_files dir handling in Make, if case refactoring]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(backported from commit 07449f692c)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit 881ed09ee6 ("build: create JSON files containing image info")
has removed the crucial empty new line from the image copy step
resulting in the following errors during make function expansion:
GZ_SUFFIX :=
bash: GZ_SUFFIX: command not found
Makefile:86: recipe for target 'openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-sysupgrade.bin' failed
Fixes: 881ed09ee6 ("build: create JSON files containing image info")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 0fb23d67f0)
The JSON info files contain details about the created firmware images
per device and are stored next to the created images.
The JSON files are stored as "$(IMAGE_PREFIX).json" and contain some
device/image meta data as well as a list of created firmware images.
An example of openwrt-ramips-rt305x-aztech_hw550-3g.json
{
"id": "aztech_hw550-3g",
"image_prefix": "openwrt-ramips-rt305x-aztech_hw550-3g",
"images": [
{
"name": "openwrt-ramips-rt305x-aztech_hw550-3g-squashfs-sysupgrade.bin",
"sha256": "db2b34b0ec4a83d9bf612cf66fab0dc3722b191cb9bedf111e5627a4298baf20",
"type": "sysupgrade"
}
],
"metadata_version": 1,
"supported_devices": [
"aztech,hw550-3g",
"hw550-3g"
],
"target": "ramips/rt305x",
"titles": [
{
"model": "HW550-3G",
"vendor": "Aztech"
},
{
"model": "ALL0239-3G",
"vendor": "Allnet"
}
],
"version_commit": "r10920+123-0cc87b3bac",
"version_number": "SNAPSHOT"
}
Signed-off-by: Paul Spooren <mail@aparcar.org>
(backported from commit 881ed09ee6)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For quite some time, the tiny (4M flash) TP-Link sysupgrade and
factory images cannot be built anymore by the buildbots, just
the initramfs-kernel.bin files are still there.
Disable these images for the buildbots and don't waste build
resources.
Note that these devices still build fine with default settings,
just not with the additional packages and config symbols for
the buildbots.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The uci config section network.globals set up in /bin/config_generate
will only be created if /proc/sys/net/ipv6 exists.
Correspondingly, lacking IPv6 support, the command
uci set network.globals.packet_steering=1
will fail with "uci: Invalid argument" as the network.globals config
has not been set up.
Fix that by adding the setup there as well.
While at it, limit the uci commit to the network config file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 636b62e8e2)
Fix the switch LAN labels for the DGND3700v1/DGND3800B router,
the order is reversed.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[cut out of bigger patch, adjust commit title/message accordingly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 583b3e4025)
Increase the SPI frequency for ELECOM WRC-1900GST and WRC-2533GST
to 40 MHz by updating the common DTSI file.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[WRC-1900GST]
Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit b5ae70d053)
The mwlwifi driver sets the default country code for EU (fi-
rmware region code 0x30) certified devices to FR (France),
not DE (Germany). Whilst this is a trivial fix, novice users
may not know how mwlwifi negatively reacts to a non-matching
country code and may leave the setting alone. Especially si-
nce it is under the advanced settings section in LuCI.
Relevant mwlwifi driver code:
0a550312dd
The mwlwifi driver readme states "Please don't change country
code and let mwlwifi set it for you." However, OpenWrt's current
behaviour does not adhere to this with its default, 'just flashed
from factory' setting for EU devices.
Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d0e8b8310f)
The original text was copy/pasted from some other package.
Adjust the package title and description to match the description
on the publishers page.
Signed-off-by: Catalin Patulea <catalinp@google.com>
[slightly adjust content and commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 492a6594b9)
urandom-seed has a separate Makefile, we can safely remove the definition here.
Fixes: 27bfde9c9f ("base-files: move urandom seed bits into separate package")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 46a6586c83)
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.
The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi
While this is a cosmetic change, backporting it to 19.07 will be a
major help for anyone doing backports of device support. Without it,
every backporter would have to remember to manually add the chosen node
to the device's DTS.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 635f111148)
This ports support for these devices from ar71xx.
Specification:
- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: v3: 560 MHz, v4: 650 MHz
- Flash: 4096 KiB
- RAM: 32 MiB
- Ethernet: 1 port @ 100M
- Wireless: SoC-integrated: QCA9533 2.4GHz 802.11bgn
In contrast to the implementation in ar71xx (reset and WiFi button),
the device actually features reset and WPS buttons.
Flashing instructions:
Upload the ...-factory.bin file via OEM web interface.
TFTP Recovery:
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to
wa801ndv3_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
TFTP recovery has only been tested with v3, and the Wiki states
that the procedure won't work for v4, which cannot be verified
or falsified at the moment.
Tested by Tim Ward (see forum):
https://forum.openwrt.org/t/ath79-support-for-tp-link-tl-wa901nd-v3-v4-v5/61246/13
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 9a477b833a)
51e16eb uclient-fetch: add option to read POST data from file
99aebe3 uclient: Add string error function
Fixes: 0c910d8459 ("uclient: Update to version 2020-06-17")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This reverts commit 0c910d8459.
We cannot use uclient Git HEAD as-is on 19.07 due to an older
version of the ustream-ssl API.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
fef6d3d uclient: Add string error function
af585db uclient-fetch: support specifying advertised TLS ciphers
c660986 uclient-fetch: add option to read POST data from file
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry-squashed from commits 05145ffbef98017228dddd166960f48e98613f4d)
The Pirelli A226M-FWB has a wrong linux partition offset, caused
by a copy-paste error. As of result of this, OpenWrt is currently
broken in this unit.
Fix it.
While at it, also use generic node names and fix the addresses
there as well.
Fixes: a27d59bb42 ("brcm63xx: switch to new partition layout
specification")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[also fix/update node names, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d64d5ed142)
It was noticed that the the whole MAC can hang when transferring data from
one ar40xx port (WAN ports) to the CPU and from the CPU back to another
ar40xx port (LAN ports). The CPU was doing only NATing in that process.
Usually, the problem first starts with a simple data corruption:
$ wget https://cdimage.debian.org/debian-cd/current/amd64/iso-cd/debian-10.4.0-amd64-netinst.iso -O /dev/null
...
Connecting to saimei.ftp.acc.umu.se (saimei.ftp.acc.umu.se)|2001:6b0:19::138|:443... connected.
...
Read error at byte 48807936/352321536 (Decryption has failed.). Retrying.
But after a short while, the whole MAC will stop to react. No traffic can
be transported anymore from the CPU port from/to the AR40xx PHY/switch and
the MAC has to be resetted.
The whole problem can be avoided by disabling IPv6 TSO for this ethernet
MAC driver.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: John Crispin <john@phrozen.org>
(backported from commit 6785695056, with
updated commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds ar71xx's GPIO setup for the 2.4GHz and 5GHz antennae
demultiplexer:
| 158 /* 2.4 GHz uses the first fixed antenna group (1, 0, 1, 0) */
| 159 ap9x_pci_setup_wmac_gpio(0, (0xf << 6), (0xa << 6));
| 160
| 161 /* 5 GHz uses the second fixed antenna group (0, 1, 1, 0) */
| 162 ap9x_pci_setup_wmac_gpio(1, (0xf << 6), (0x6 << 6));
This should restore the range and throughput of the 2.4GHz radio
on all the derived wndr3700 variants and versions with the AR7161 SoC.
A special case is the 5GHz radio. The original wndr3700(v1) will
benefit from this change. However the wndr3700v2 and later revisions
were unaffected by the missing bits, as there is no demultiplexer
present in the later designs.
This patch uses gpio-hogs within the device-tree for all
wndr3700/wndr3800/wndrmac variants.
Notes:
Based on the PCB pictures, the WNDR3700(v1) really had eight
independent antennae. Four antennae for each radio and all of
those were printed on the circut board.
The WNDR3700v2 and later have just six antennae. Four of those
are printed on the circuit board and serve the 2.4GHz radio.
Whereas the remaining two are special 5GHz Rayspan Patch Antennae
which are directly connected to the 5GHz radio.
Hannu Nyman dug pretty deep and unearthed a treasure of information
regarding the history of how these values came to be in the OpenWrt
archives: <https://dev.archive.openwrt.org/ticket/6533.html>.
Mark Mentovai came across the fixed antenna group when he was looking
into the driver:
fixed_antenna_group 1, (0, 1, 0, 1)
fixed_antenna_group 2, (0, 1, 1, 0)
fixed_antenna_group 3, (1, 0, 0, 1)
fixed_antenna_group 4, (1, 0, 1, 0)
Fixes: FS#3088
Reported-by: Luca Bensi
Reported-by: Maciej Mazur
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Debugged-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 61307544d1)
CONFIG_VLAN_8021Q was explicitely disabled in oxnas kernel config.
Don't do that, so VLANs can be used on the target.
Fixes: dcc34574ef ("oxnas: bring in new oxnas target")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fd0cc72d9c)
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of Flash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)
Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to web interface:
[V1] http://192.168.0.1
[V2] http://192.168.0.254
Default user is "admin" & password is "admin".
On V2, there is no DHCP server running by default, so remember to set
IP manually.
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware:
[V1] "*.factory.bin"
[V2] "*.factory-us.bin" or "*.factory-eu.bin" for eu model
Web interface may complain if filename is too long. In such case,
rename .bin to something shorter.
- Click upgrade
Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
Serial Configuration 115200 8n1
- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
(IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
(e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
(e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
(e.g bootm 0x9f020000)
Notes:
When porting from ar71xx target to ath79, I found out that on V2,
reset button is on GPIO12 and active low, instead of GPIO11 and
active high. By cross-flashing V1 firmware to V2, I confirmed
the same is true for V1.
Also according to manual of V1, this one also has green
LED instead of blue - both of those issues were fixed accordingly.
The MAC address assignment has been checked with OEM firmware.
Installation manual based on ar71xx support by Thomas Roberts
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit message, add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 7e513136c6)
Ubiquiti WA devices with newer hw version 2011K require UBNT_VERSION
to be at least 8.5.3, otherwise the image is rejected:
New ver: WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3
Versions: New(525568) 8.5.0, Required(525571) 8.5.3
Invalid version 'WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3'
For consistency, also increase version number for XC devices.
Tested-by: Pedro <pedrowrt@cas.cat>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit 95caa3436d)
Since the wireless LED was used for boot and set up with a DT
trigger, the WiFi indication hasn't worked on ath79 at all.
In addition, a look into the manual revealed that the OEM
configuration is as follows:
LED 1 (green): power
LED 2 (green): configurable
LED 3 (red): wireless
So, let's just keep the WiFi trigger and convert the rest to its
"intended" use.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 705fe43522)
During porting support for this router to ath79 target
it was discovered that GPIO mapping was incorrect (GPIO11 active high).
Correct mapping for both V1 and V2 is GPIO12 active low.
Default configuration from GPL source for V2 explicitly states this, and
this was confirmed experimentally on ath79 by looking on
/sys/kernel/debug/gpio. Correctness of this was also validated for V1 by
cross-flashing vendor firmware for V1 on V2 hardware, in which reset
button also worked.
Fix it.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit f841e70640)
The TP-Link TL-MR3020 has a three-state mode slider which was previously
integrated as a button (EV_KEY). This led to spurious activations of
failsafe mode.
Set the type for the button to switch (EV_SW), to avoid unintended
activations of failsafe mode.
Related: commit 27f3f493de ("gpio-button-hotplug: unify polled and
interrupt code")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b017a016cc)
The -O option for the tplink-v1-header was missing for the TP-Link
TL-WR902AC v1, while safeloader and MTDPARTS where set up with a
single firmware partition.
This led to bootloops after using sysupgrade.
Fixes: FS#3118
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a7b07f8ba8)
Also ensure that the error message is actually printed to stderr and that
the rule generation is aborted if an interface cannot be resolved.
Ref: https://github.com/openwrt/luci/issues/3975
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 559b338466)
Add a local hack to prevent the Broadcom WPA authenticator process from
inheriting the lock descriptor 1000 used to prevent concurrent executions
of the init script.
Without this fix, repeated invocations of /etc/init.d/network, e.g. for
obtaining the enabled state, would hang forever.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit a03d6d2fab)
078bb57 uci: reset uci_ptr flags when merging options during section add
3df62bc session: deny access if password login is disabled
efe51f4 iwinfo: add current hw and ht mode to info call
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
86818eaa976b blob: make blob_parse_untrusted more permissive
cf2e8eb485ab tests: add fuzzer seed file for crash in blob_len
c2fc622b771f blobmsg: fix length in blobmsg_check_array
639c29d19717 blobmsg: simplify and fix name length checks in blobmsg_check_name
66195aee5042 blobmsg: fix missing length checks
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit b371182d24)
5e75160 blobmsg: fix attrs iteration in the blobmsg_check_array_len()
eeddf22 tests: runqueue: try to fix race on GitLab CI
89fb613 libubox: runqueue: fix use-after-free bug
1db3e7d libubox: runqueue fix comment in header
7c4ef0d tests: list: add test case for list_empty iterator
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a765b063ee)
Looking at the current upstream driver implementation, it seems like the
TX/RX flow control is enabled only if the flow control pause option is
resolved from the device/link partner advertisements (or otherwise set).
On the other hand, our current in-tree driver force enables TX/RX
flow control by default, thus possibly leading to TX timeouts if the
other end sends pause frames (which are not properly handled?):
WARNING: CPU: 3 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x1ac/0x324
NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out
Disabling the flow control on PORT 5 MAC seems to fix this issues as the
pause frames are then filtered out. While at it, I'm removing the if
condition completely as suggested, since this code is run only on mt7621
SoC, so there is no need to check for the silicon revisions.
Ref: https://lists.openwrt.org/pipermail/openwrt-devel/2017-November/009882.html
Ref: https://forum.openwrt.org/t/mtk-soc-eth-watchdog-timeout-after-r11573/50000/12
Suggested-by: Felix Fietkau <nbd@nbd.name>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c8f8e59816)
crypto_bignum_rand() use needless time-consuming filtering
which resulted in SAE no longer connecting within time limits.
Import fixes from hostap upstream to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 631c437a91)
00b921d80ac0 Do not print line number in debug messages
96c42c5ed320 Fix length checks in cert_load()
fe06b4b836b3 usign-exec: improve usign -F output handling
19f9e1917e1b usign-exec: return code fixes
077feb5b5824 usign-exec: close writing end of pipe early in parent process
7ec4bb764e1e usign-exec: remove redundant return statements
5a738e549d31 usign-exec: change usign_f_* fingerprint argument to char[17]
112488bbbccc usign-exec: do not close stdin and stderr before exec
38dcb1a6f121 usign-exec: fix exec error handling
a9be4fb17df2 usign-exec: simplify usign execv calls
854d93e2326a Introduce read_file() helper, improve error reporting
afc86f352bf7 Fix return code of write_file()
fdff10852326 stdout/stderr improvements
dddb2aa8124d ci: fix unit test failures by enabling full ucert build
5f206bcfe5c2 ci: enable unit testing
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Disable the Netgear WNR2000 v2 image by default as the device has
insufficient flash space for release build images.
Ref: https://forum.openwrt.org/t/devices-too-big-to-save-overlay/18161/72
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
[drop change on netgear-wnr3500l-v1-na]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fixes the following build error with GCC 10:
/usr/bin/ld: read_fs.o:(.bss+0x0): multiple definition of `swap'; mksquashfs.o:(.bss+0x1b2a88): first defined here
And a compile warning.
Fixes: FS#3104, FS#3119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1bbc1aa884)
This ports support for the TL-WA901ND v4 and v5 from ar71xx to ath79.
They are similar to the TP9343-based TL-WR940N v3/v4 and TL-WR941ND v6.
Specifications:
SoC: TP9343
Flash/RAM: 4/32 MiB
CPU: 750 MHz
WiFi: 2.4 GHz b/g/n
Ethernet: 1 port (100M)
Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to * (see below)
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
* The image name for TFTP recovery is wa901ndv4_tp_recovery.bin for
both variants.
In ar71xx, a MAC address with offset 1 was used for ethernet port.
That's probably wrong, but this commit sticks to it until we know
the correct value.
Like in ar71xx, this builds the default factory.bin with EU country
code.
Thanks to Leonardo Weiss for testing on the v5.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 4a61a88f90)
This adds support for the various clones of the TL-WA830RE recently
supported in fb99ac6807 ("ath79: add support for TP-Link TL-WA830RE v1"):
- tplink,tl-wa701nd-v1
- tplink,tl-wa730re-v1
- tplink,tl-wa801nd-v1
- tplink,tl-wa830re-v1 (already supported)
- tplink,tl-wa901nd-v1
Since these devices are 100%-clones in ar71xx, this patch adds all
of them without run-testing (as this has been done for TL-WA830RE v1).
Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftpboot 0x80000000 \
openwrt-ath79-tiny-tplink_tl-waxxxxx-v1-squashfs-factory.bin
> erase 0x9f020000 +0x3c0000
> cp.b 0x80000000 0x9f020000 0x3c0000
> bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 2f1cc5c3d5)
The TL-WR940N v6 is similar to v3/v4, it just has different
LEDs and MAC address assignment.
Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet
The use of LEDs is based on ar71xx, so blue LED is used for WAN
and orange LED for diag (boot/failsafe/etc.).
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
wr940nv6_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Thanks to Manuel Kock for reviewing and testing this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Manuel Kock <github.web@manu.li>
(backported from commit fbd00bb8d4)
This ports support for the TL-WA830RE v1 range extender from ar71xx to
ath79.
Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftpboot 0x80000000 \
openwrt-ath79-tiny-tplink_tl-wa830re-v1-squashfs-factory.bin
> erase 0x9f020000 +0x3c0000
> cp.b 0x80000000 0x9f020000 0x3c0000
> bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image
The device seems to be a clone of the following devices not yet
added to ath79:
- tl-wa701nd-v1
- tl-wa730re-v1
- tl-wa801nd-v1
- tl-wa901nd-v1
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
[make use of ar7240_tplink.dtsi, add note about clones]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit fb99ac6807)
The current set of TP-Link devices with ar7240 SoC all share
the same DTSI file. As the latter is very similar to the
definition required for the to-be-supported TP-Link TL-WA devices
with ar7240, this patch splits the definitions into a shared part
for all TP-Link devices (ar7240_tplink.dtsi) and a file containing
the specific setup for the present TL-WR devices
(ar7240_tplink_tl-wr.dtsi), equivalent to the former
ar7240_tplink_tl-wr74xn-v1.dtsi.
While at it, remove unused firmware partition label and rename
pinmux_switch_led_pins.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 273e00c4a5)
