The D-Link DWL-8610AP does not make use of the B53 switch
like most equipment. It lies dormant and the machine is using
eth0 and eth1 directly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The D-Link DWL-8610AP is a pretty straight-forward BC53016
device, D-Link has invented a firmware package format which
is a tar file, and we implement this for the factory image.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
in both the stable and the testing kernel
h2+/h3/h5 devices have a Secure ID that can be read from
`/sys/bus/nvmem/devices/sunxi-sid0/nvmem`.
Enabling CONFIG_NVMEM_SYSFS grants sysfs access from userspace.
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
This hack was to bring all existing installations to the newest GRUB
version as fast as possible. Since 19.07.x is EoL we can assume this
task is completed. Now sysupgrade will solely be responsible for
bootloader upgrade.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
The Buffalo LinkStation LS220DE is a dual bay NAS, based on Marvell
Armada 370
Hardware:
SoC: Marvell Armada 88F6707
CPU: Cortex-A9 800 MHz, 1 core
Flash 1: SPI-NOR 1 MiB (U-Boot)
Flash 2: NAND 512 MiB (OS)
RAM: DDR3 256 MiB
Ethernet: 1x 1GbE
USB: 1x 2.0
SATA: 2x 3Gb/s
LEDs/Input: 5x / 2x (1x button, 1x slide-switch)
Fan: 1x casing
Flash instructions, from hard drive:
1. Get access to the "boot" partition at the hard drive where the stock
firmware is installed. It can be done with acp-commander or by
plugging the hard drive to a computer.
2. Backup the stock uImage:
mv /boot/uImage.buffalo /boot/uImage.buffalo.bak
3. Move and rename the Openwrt initramfs image to the boot partition:
mv openwrt-initramfs-kernel.bin /boot/uImage.buffalo
4. Power on the Linkstation with the hardrive inside. Now Openwrt will
boot, but still not installed.
5. Connect via ssh to OpenWrt:
ssh root@192.168.1.1
6. Rename boot files inside boot partition
mount -t ext3 /dev/sda1 /mnt
mv /mnt/uImage.buffalo /mnt/uImage.buffalo.openwrt.bak
mv /mnt/initrd.buffalo /mnt/initrd.buffalo.bak
7. Format ubi partitions at the NAND flash ("kernel_ubi" and "ubi"):
ubiformat /dev/mtd0 -y
ubidetach -p /dev/mtd1
ubiformat /dev/mtd1 -y
8. Flash the sysupgrade image:
sysupgrade -n openwrt-squashfs-sysupgrade.bin
9. Wait until it finish, the device will reboot with OpenWrt installed
on the NAND flash.
Restore the stock firmware:
1. Take the hard drive used for the installation and restore boot backup
files to their original names:
mount -t ext3 /dev/sda1 /mnt
mv /mnt/uImage.buffalo.bak /mnt/uImage.buffalo
mv /mnt/initrd.buffalo.bak /mnt/initrd.buffalo
2. Boot from the hard drive and perform a stock firmware update using
the Buffalo utility. The NAND will be restored to the original
state.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The USB port on the MR8300 randomly fails to feed bus-powered devices.
This is caused by a misconfigured pinmux. The GPIO68 should be used to
enable the USB power (active low), but it's inside the NAND pinmux.
This GPIO pin was found in the original firmware at a startup script in
both MR8300 and EA8300. Therefore apply the fix for both boards.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
MT7621 uses a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Netgear R6220, WAC104 and WNDR3700 v5.
According to bootlog, MT7612E (5GHz) is connected to pcie0, and
MT7603E (2GHz) is connected to pcie2:
[2.758986] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
[2.772862] mt7621-pci 1e140000.pcie: PCIE0 enabled
[2.782579] mt7621-pci 1e140000.pcie: PCIE2 enabled
...
[3.009151] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[3.125715] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
Tested-by: Maximilian Baumgartner <aufhaxer@googlemail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[felix.bau@gmx.de: adjust commit message for Netgear devices]
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Assign fan with 4 active cooling levels to be used for the main CPU as
well as external SerDes units.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Several fixes for the Puzzle WT61P803 hwmon driver were needed to make
it behave well as thermal cooling device:
- wire-up cooling device with OF node in device tree
- properly parse cooling-levels (u32 with range check vs. u8)
- actually use cooling-levels
- keep current state and only write to uC if state has changed
(avoids flooding the uC with commands which will result in uC crashing)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch adds supports for GL-X1200.
Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB
- RAM: 128 MiB DDR2
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: QCA9563(2.4GHz) and QCA9886(5GHz)
- SIM: 2x SIM card slots
- MicroSD: 1x microSD slot
- Antenna: 2x external 5dBi antennas
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 16x LEDs (3x GPIO controllable)
- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)
- OEM U-Boot supplies HTTP/GUI access
Implementation Notes
====================
Both the NOR and NAND variants boot off a NOR-based kernel,
consistent with the OEM's firmware.
The mode LEDs are
* Boot, Running system
* Failsafe 2G
* Upgrade 5G
Installation
============
Using sysupgrade
----------------
sysupgrade may be used to install a NAND image on a device running
a NAND image or a NOR image on a device running a NOR image. It is
recommended to *not* preserve config when upgrading from OEM firmware
or previous versions of OpenWrt. No supported sysupgrade path should
require "force". Transitioning from NOR to NAND can be accomplished
Using U-Boot
------------
The OEM U-Boot can be put into a graphical, firmware-upload mode by
holding down the button on the side of the router while applying power
and for a bit more than five seconds following with the current OEM
U-Boot. The power LED will come on, then the 5G LED will flash five
times, about once a second. When the 5G LED stops flashing and the
2G LED lights solid, the router's U-Boot will provide an upload page
at http://192.168.1.1/ Either a browser may be used to upload an image,
or a utility such as curl may be used:
curl -X POST -F gl_firmware=\@*-nand-squashfs-factory.img \
http://192.168.1.1/index.html
or
curl -X POST -F gl_firmware=\@*-nor-squashfs-sysupgrade.bin \
http://192.168.1.1/index.html
Note that NOR vs. NAND is based on the file name extension.
Signed-off-by: Xinfa Deng <xinfa.deng@gl-inet.com>
The CONFIG_PPC_QUEUED_SPINLOCKS configuration option is not defined for
kernel 5.15, it is defined for kernel 5.10.
This fixes the compilation of mpc85xx/p2020 with kernel 5.15.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
They were backported to stable kernels but we backport more stuff on our
own so we have to pick up few remaining.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The default kernel should be switched to 5.15 in order to enable testing
by a broader audience.
Tested on TP-Link TL-WDR4900 v1.
Acked-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Armada 7040 uses a rather small 15MB memory window for every PCI adapter,
however this is not sufficient for Qualcomm QCA6390 802.11ax cards that
are shipped along with the OpenWrt WLAN model of MOCHAbin as ath11k
requires at least 16MB of memory.
So, similar to what MACCHIATOBin has been doing for years, lets move
to using the second PCIe 2 memory window and expand it to 128MB to
make it future proof.
This has been already sent upstream [1].
[1] https://lore.kernel.org/linux-arm-kernel/20230219121418.1395401-1-robert.marko@sartura.hr/
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This patch introduces DSA support for TP-Link TL-WDR4900 v1 switch.
Swconfig driver for QCA8327 switch is removed because this router is
only one device which use Qualcom swconfig switch.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Nick Hainke <vincent@systemli.org> # TP Link WDR4900 v1 (5.15)
Wiflyer WF3526-P and Zbtlink ZBT-WE1326 have the same circuit design.
Installing the misunderstading firmware of ZBT-WE3526 will cause Wi-Fi
not work due to allocate the wrong pcie port. Add alternative name to
help users easily build or download the correct firmware.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
MT7621 gets a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Zbtlink ZBT-WE1326.
According to the bootlog, MT7612E (5 GHz) is connected to pcie1, and
MT7603E (2 GHz) is connected to pcie2:
[4.197658] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[4.204609] mt7621-pci 1e140000.pcie: PCIE1 enabled
[4.209476] mt7621-pci 1e140000.pcie: PCIE2 enabled
...
[4.307988] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[4.367206] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The name of squashfs is confusing since in reality it's a really old
version using an old lzma library. This tools is used for old ath79
netgear target and to produde a fake squasfs3 image needed for some
specific bootloader from some OEM (AVM for example)
Rename squashfs tool to squasfs3-lzma to better describe it.
Rename the installed bin from mksquashfs-lzma to mksquashfs3-lzma.
Use tar transform to migrate the root directory in tar to the new
naming.
Drop redundant PKG_CAT variable not needed anymore.
Also update any user of this tool.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Chromium devices (like Google WiFi) have ramoops memory reserved by the
bootloader. Let's enable the ramoops kernel module by default, so we get
better crash logging.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Chromium devices (like OnHub) have ramoops memory reserved by the
bootloader. Let's enable the ramoops kernel module by default, so we get
better crash logging.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
FCC ID: A8J-EPG600
Engenius EPG600 is an indoor wireless router with
1 Gb ethernet switch, dual-band wireless,
internal antenna plates, USB, and phone lines (not supported)
this board is a Senao device:
the hardware is equivalent to EnGenius ESR600 (except for phone lines)
the software is Senao SDK which is based on openwrt and uboot
which uses the legacy Senao header with Vendor / Product IDs
to verify the firmware upgrade image.
**Specification:**
- MT7620 SOC MIPS 24kec, 2.4 GHz WMAC, 2x2
- RT5592N WLAN PCI chip, 5 GHz, 2x2
- QCA8337N Gb SW RGMII GbE, SW P0 -- SOC P5, 5 LEDs
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 64 MB RAM NT5TU32M16
- UART console J2, populated
- USB 2.0 port direct to SOC
- 6 GPIO LEDs power, 2G, 5G, wps2g, wps5g, line
- 3 buttons reset, wps, "reg" (registeration)
- 4 antennas internal omni-directional plates
NOT YET SUPPORTED: VoIP
- Si3050-FT + Si3019-FT Voice DAA, SPI control, PCM data
- Phone Ports "TEL", "LINE" RJ11, 4P2C (2 pins)
**MAC addresses:**
MAC address labeled as MAC ADDRESS
MACs present in both wifi cal data and uboot environment
eth0.1/phy1 ---- *:82 rf 0x4
phy0 ---- *:83 factory 0x4
eth0.2 MAC *:b8 "wanaddr"
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.0.1
username and password 'admin'
Navigate to gear icon, "Device Management", "Tools"
select the factory.dlf image
Upload and verify checksum
Method 2: Serial to upload initramfs:
Follow directions for TFTP recovery
upload and boot initramfs and do a sysupgrade
**TFTP recovery:**
Requires UART serial console, reset button does nothing
rename initramfs-kernel.bin to 'uImageEPG600'
make available on TFTP server at 192.168.99.8
power board, interrupt boot with "4"
execute `tftpboot` and `bootm` (with the load address)
**Return to OEM:**
Images from OEM are provided, but not compatible
with openwrt sysupgrade. So it must be modified.
Alternatively, back up all mtd partitions before flashing
**Note on switch registers:**
The necessary registers needed for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by using the following lines in the switch driver ar8327.c
in the function 'ar8327_hw_config_of'
where 'qca,ar8327-initvals' is parsed from DTS
before the new register values are written:
pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE));
pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE));
pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP));
Signed-off-by: Michael Pratt <mcpratt@pm.me>
in order for the option ephy-disable to work
without also needing ephy-base option,
we have to skip all the lines that write to mdio addresses that
assume those addresses do not have an external switch.
Otherwise, ephy ports will be disabled in hardware,
but register writes still happen as if they are enabled.
Split the functions so that other things are done first,
and ephy port setup can be skipped with a simple "return".
Tested on Engenius EPG600 (MT7620A ver:2 eco:3)
with QCA8337 external switch
Ref: cc6fd6fbb5 ("ramips: mt7620: add ephy-disable option to switch driver")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Zyxel NBG7815 supports bluetooth with blsp1_uart3.
Configuration are already added to dts file, device needs only module to working bluetooth properly.
Tested at below posts:
https://forum.openwrt.org/t/openwrt-support-for-armor-g5-nbg7815/98598/259?u=itork
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Karol Przybylski <karol.przybylski@esm-technology.pl>
Specifications:
* SoC: MediaTek MT7622BV
* RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
* Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ)
* Wi-Fi 2.4/5 GHz 4T4R:
* 2.4 GHz: MediaTek MT7622BV
* 5 GHz: MediaTek MT7915AN/MT7975AN
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY)
* Switch: MediaTek MT7531AE
* LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4,
Wifin and Wifia dual-colour LEDs + Reset pin)
* UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v,
115200n8
* Power: 12 VDC, 2.5 A
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* U-Boot allows booting an initramfs image via TFTP as follows:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.100
tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
bootm
Known Limitations:
* The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the
moment. If connected to a multi-gig port the speed has to be manually
set to 1G/full either for the switch port or in OpenWrt. For example
add the following to /etc/rc.local to set it on boot:
/usr/sbin/ethtool -s wan speed 1000 duplex full
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to WAX206 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar
* openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts
DTS file for this device.
* openwrt/target/linux/mediatek/image/mt7622.mk
Image creation code for this device
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[fix WAN port (1G only), adjust partition layout, adjust image creation]
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Some devices like ZBT WE1326 and ZBT WF3526-P and some Netgear models need
to delay phy port initialization after calling the mt7621_pcie_init_port()
driver function to get into reliable boots for both warm and hard resets.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This commit fixes the following commit
f584fb2f7e kernel: import accepted MediaTek Ethernet patches
Unrefreshed patches caused the CI to fail.
Signed-off-by: Paul Spooren <mail@aparcar.org>
With 5.15 kernel version Linksys EAX500 family devices suffered from a
big regression where the Ethernet switch became silent and started to
malfunction.
It was discovered later that the cause was not really the kernel upgrade
itself but a hackish implementation of the hw implementation of these
special routers.
In the original Linksys source code, GPIO 63 was handled in a special way
and was reset on reboot.
Normally GPIO 63 is used for pcie2 reset but in every device we support,
pcie2 is actually never used as nothing is attached to it.
Linksys rerouted GPIO 63 to the switch reset pin and deviates from
common hw implementation.
Till now it was used an hack to handle this case... It was set pcie3 as
working (while actually nothing was connected), set it to output low
(for assert-deassert from the pcie init code) and be done with it.
The result was that the GPIO was reset for enough time in early boot and
everything worked correctly.
This hack implementation was born to fail from the very start and in
kernel 5.15 finally problem arised.
In 5.15 pcie code changed and now the GPIO reset pin is not asserted as
probe won't fail if nothing is connected to the line (the old behaviour)
This result in the switch hold the reset pin and the Ethernet switch
dead.
On top of that with 5.15 code got optimized and simply attaching the
GPIO reset to the mdio wasn't enough as the switch require at least 10ms
to be correctly reset.
So implement finally a correct solution where:
- pcie2 is correctly disabled (nothing attached, unused)
- drop the wrong output-low for pcie2 reset pin
- define GPIO 63 as switch reset
- Add the reset-gpios to the mdio0 node
- Set the reset-post-delay-us to 12ms to correctly give time the switch
to reset
Fixes: #10983
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
I tested kernel 5.15 on my device for several times without any problems.
In my tests, 5.15 kernel has performance improvements such MGLRU.
Finally, initial kernel 6.1 support is imminent. All ramips subtargets have
5.15 as testing kernel. So, it's time to change.
Tested on my Archer C6 v3.2 (mt7621)
Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
[reformat commit subject and message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Wrong pcie port number for WLAN causes missing 5g WLAN interface with 5.15
kernel. This changes port from pcie0 to pcie1 in dtsi.
[1.166330] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[1.180073] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[1.193889] mt7621-pci 1e140000.pcie: PCIE1 enabled
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
ipq807x does not compile-in hwmon core, and this is leading to the hwmon
code in AQR driver not being compiled due to IS_REACHABLE(CONFIG_HWMON)
evaluating to false as hwmon is being built as a module.
So, lets not compile-in Aquantia PHY driver so it can be included as kmod
instead to have functioning hwmon.
This allows using the thermal sensors in AQR-s as thermal zones for
cooling devices like fans.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace a standalone init.d script with a platform implementation as
supported by netifd. This avoids a race between netifd and target
specific setups.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Replace a standalone init.d script with a platform implementation as
supported by netifd. This avoids a race between netifd and target
specific setups.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Import some accepted and pending upstream patches for mtk_eth_soc,
replacing some semantically equivalent local patches and fixing issues
when operating the PCS in 1G SGMII mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
