This commit adds the currently missing Mellanox
Spectrum-2, Spectrum-3, and Spectrum-4 firmware files.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On latest Intel x86 CPUs, DMC firmware is required for the iGPU to reach
its lowest power states. If the driver cannot load it, it will print a
warning and unnecessarily make the iGPU draw a bit more power when idle.
GUC firmware (various "offload" mechanisms that deal with scheduling GPU
workloads) and HUC firmware (required for accelerated media codec
operations for HEVC/H.265) are probably more niche, but could also
provde useful for some - for example, when building an
Intel/OpenWrt-based security camera.
Signed-off-by: Johannes Truschnigg <johannes@truschnigg.info>
Link: https://github.com/openwrt/openwrt/pull/16069
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Bump `omnia-mcu-firmware` to version 4.1.
This version fixes the following issue on boards with GD32 MCU:
* the user has old GD32 MCU bootloader and application (version 2.0)
* the user upgraded MCU application firmware to newer version (from
2.99 to 4.0)
* the user wants to upgrade application again, but it is impossible,
because when MCU application firmware jumps into the old MCU
bootloader firmware (2.0), the old bootloader firmware gets stuck in
exception
* the user has to restart the board and upgrade the bootloader firmware
first, which is not ideal, since if bootloader firmware upgrade is
interrupted, the board gets bricked
Therefore the `omnia-mcutool` utility version 0.3-rc3 will refuse to
upgrade MCU application firmware to versions 2.99 to 4.0 if the MCU
bootloader firmware is at version 2.0.
For users to be able to upgrade MCU application firmware on GD32
boards, they will need this new 4.1 version.
Users that already upgraded the MCU application firmware to a version
version between 2.99 and 4.0 (using a previous version of the
`omnia-mcutool` utility) have no other choice but to upgrade MCU
bootloader firmware as well.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/16159
Signed-off-by: Robert Marko <robimarko@gmail.com>
Cambium Networks XE3-4 is a tri-radio Wi-Fi 6/6E 4×4/2×2 AP.
Hardware:
Model: Cambium Networks XE3-4
CPU: IPQ6010/AP-CP01-C3, SoC Version: 1.0 @ 800 MHz
Memory: 1 GiB
Flash: 512 MiB Macronix MX30UF2G18AC + W25Q128FW
Ethernet: 1x 1 GbE (QCA8072)
1x 2.5 GbE (QCA8081)
Buttons: 1x Reset
Serial: TX, RX, GND
Baudrate: 115200
Radios: Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 2GHz
Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 5GHz
Qualcomm Atheros QCN9074 802.11ax - 4x4 - 5GHz or 6GHz
BLE 4.1
Power: 32.0W 802.3bt5 PoE++
25.5W 802.3at with USB, BT disabled
Size: 215mm x 215mm
Ports: 1x USB 2.0
Antenna: 6 GHz: 6.29 dBi, Omni 30 dBm
5 GHz: 6.12 dBi, Omni 31 dBm
2.4 GHz: 4.85 dBi, Omni 29 dBm
LEDs: Multi-color status LEDs
Mounting: Wall, ceiling or T-bar
Installation: Serial connection
1. Open the AP to get access to the board. Connect RX, TX and GND.
2. Power on the AP, and short the CS pin of the SPI flash with
one of the APs GND pins.
3. Transfer the initramfs image with TFTP
(Default server IP is 192.168.0.120)
# tftpboot factory.ubi
4. Flash the rootfs partition
# flash rootfs
5. Reboot the AP
# reset
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15633
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a new package, omnia-mcu-firmware, containing firmware binaries for
the microcontroller on the Turris Omnia router.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
Build the amd64-microcode package on all architectures even if it only
makes sense to use it on x86. If the package build is done by a builder
not building for x86 it will not include the package otherwise.
Link: https://github.com/openwrt/openwrt/pull/16031
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package the firmware files in the target specific build step and not in
the architecture common step. The architecture common step is not
necessary build for the ipq40xx target. If it is build for a different
target these packages are not packaged at all. This moves the build to
the ipq40xx target specific build step. This change is needed to make
the firmware files show up in the buildbot images.
Fixes: 02db8a19cb ("firmware: add Intel/Lantiq VRX518 ACA firmware package")
Fixes: 07b0e6f3d9 ("firmware: add Intel/Lantiq VRX518 PPE firmware package")
Fixes: 13eb1f564a ("firmware: add Intel/Lantiq VRX518 DSL firmware package")
Link: https://github.com/openwrt/openwrt/pull/16031
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required by the DSL CPE API driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This firmware is used by the vrx518 tc driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This firmware is used by the vrx518 ep driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Changes:
2a768c4 wireless-regdb: Update regulatory rules for Mongolia (MN) on 6GHz
04875d9 wireless-regdb: Update regulatory rules for Saudi Arabia (SA) on 6GHz
b7bced8 wireless-regdb: Update regulatory rules for South Africa (ZA) on 6GHz
7bc8615 wireless-regdb: Update regulatory info for Thailand (TH) on 6GHz
f901fa9 wireless-regdb: Update regulatory info for Malaysia (MY) for 2022
d72d288 wireless-regdb: Update regulatory info for Morocco (MA) on 6GHz
414face wireless-regdb: Update regulatory info for Chile (CL) on 6GHz
1156a08 wireless-regdb: Update regulatory info for Mexico (MX) on 6GHz
cc6cf7c wireless-regdb: Update regulatory info for Iceland (IS) on 6GHz
ce03cc0 wireless-regdb: Update regulatory info for Mauritius(MU) on 6GHz
7e37778 wireless-regdb: Update regulatory info for Argentina (AR) on 6GHz
56f3a43 wireless-regdb: Update regulatory info for United Arab Emirates (AE) on 6GHz
3cb8b91 wireless-regdb: Update regulatory info for Colombia (CO) on 6GHz
3682ce5 wireless-regdb: Update regulatory info for Costa Rica (CR) for 2021
dd4ffe7 wireless-regdb: Update regulatory info for Dominican Republic (DO) on 6GHz
f8ef7da wireless-regdb: Update regulatory info for Liechtenstein (LI) on 6GHz
a9ecabe wireless-regdb: Update regulatory info for Jordan (JO) for 2022
5a9fdad wireless-regdb: Update regulatory info for Kenya (KE) for 2022
19326c3 wireless-regdb: Update regulatory info for Macao (MO) for 2024
4838054 wireless-regdb: update regulatory database based on preceding changes
Link: https://github.com/openwrt/openwrt/pull/15921
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
BDFs come from latest firmware, version 1.1.19.209880 (2022-06-20):
- /lib/firmware/IPQ4019/v1/FCC/boardData_1_0_IPQ4019_DK04_2G.bin
- /lib/firmware/IPQ4019/v1/FCC/boardData_1_0_IPQ4019_DK04_5G.bin
- /lib/firmware/QCA9888/v1/FCC/boardData_2_0_QCA9888_5G_Y9690_SBS_HB.bin
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15844
Signed-off-by: Robert Marko <robimarko@gmail.com>
Debian changelog:
intel-microcode (3.20240531.1) unstable; urgency=medium
* New upstream microcode datafile 20240531
* Fix unspecified functional issues on Pentium Silver N/J5xxx,
Celeron N/J4xxx
* Updated Microcodes:
sig 0x000706a1, pf_mask 0x01, 2024-04-19, rev 0x0042, size 76800
* source: update symlinks to reflect id of the latest release, 20240531
-- Henrique de Moraes Holschuh <hmh@debian.org> Sat, 01 Jun 2024 11:49:47 -0300
intel-microcode (3.20240514.1) unstable; urgency=medium
* New upstream microcode datafile 20240514
* Mitigations for INTEL-SA-01051 (CVE-2023-45733)
Hardware logic contains race conditions in some Intel Processors may
allow an authenticated user to potentially enable partial information
disclosure via local access.
* Mitigations for INTEL-SA-01052 (CVE-2023-46103)
Sequence of processor instructions leads to unexpected behavior in
Intel Core Ultra Processors may allow an authenticated user to
potentially enable denial of service via local access.
* Mitigations for INTEL-SA-01036 (CVE-2023-45745, CVE-2023-47855)
Improper input validation in some Intel TDX module software before
version 1.5.05.46.698 may allow a privileged user to potentially enable
escalation of privilege via local access.
* Fix for unspecified functional issues on 4th gen and 5th gen Xeon
Scalable, 12th, 13th and 14th gen Intel Core processors, as well as for
Core i3 N-series processors.
* Updated microcodes:
sig 0x000806f8, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0, size 581632
sig 0x000806f7, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0
sig 0x000806f6, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0
sig 0x000806f5, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0
sig 0x000806f4, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0
sig 0x000806f8, pf_mask 0x10, 2024-02-05, rev 0x2c000390, size 614400
sig 0x000806f6, pf_mask 0x10, 2024-02-05, rev 0x2c000390
sig 0x000806f5, pf_mask 0x10, 2024-02-05, rev 0x2c000390
sig 0x000806f4, pf_mask 0x10, 2024-02-05, rev 0x2c000390
sig 0x00090672, pf_mask 0x07, 2023-12-05, rev 0x0035, size 224256
sig 0x00090675, pf_mask 0x07, 2023-12-05, rev 0x0035
sig 0x000b06f2, pf_mask 0x07, 2023-12-05, rev 0x0035
sig 0x000b06f5, pf_mask 0x07, 2023-12-05, rev 0x0035
sig 0x000906a3, pf_mask 0x80, 2023-12-05, rev 0x0433, size 222208
sig 0x000906a4, pf_mask 0x80, 2023-12-05, rev 0x0433
sig 0x000906a4, pf_mask 0x40, 2023-12-07, rev 0x0007, size 119808
sig 0x000b0671, pf_mask 0x32, 2024-01-25, rev 0x0123, size 215040
sig 0x000b06e0, pf_mask 0x11, 2023-12-07, rev 0x0017, size 138240
sig 0x000c06f2, pf_mask 0x87, 2024-02-05, rev 0x21000230, size 552960
sig 0x000c06f1, pf_mask 0x87, 2024-02-05, rev 0x21000230
* source: update symlinks to reflect id of the latest release, 20240514
-- Henrique de Moraes Holschuh <hmh@debian.org> Thu, 16 May 2024 21:40:52 -0300
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
- 2.4 GHz: Qualcomm QCN5024 4x4
- 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
- Power: (Green and red)
- Front: (Blue, green, red and white)
* Buttons:
- 1x Soft reset
- 1x Sync/WPS
* Power: 12V DC Jack
Installation instructions (Telnet):
-----------------------------------
*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate
1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:
`fw_setenv bootcmd 'env default -a; saveenv; reset'`
5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.
6. Run the following command:
`fw_printenv`
It should look similar to the below:
```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```
**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**
7. Run the following command:
`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`
(This should match what's in the bootcmd variable displayed in step 6)
8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```
9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.
10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1
11. Once OpenWrt has booted, update the bootcmd using the following command:
`fw_setenv bootcmd 'run wrtboot'`
12. Flash the sysupgrade image
13. It should boot into OpenWrt
References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
Changes:
73529a8 Revert "wireless-regdb: Update and disable 5470-5730MHz band according to TPC requirement for Singapore (SG)"
87941e4 wireless-regdb: Update regulatory rules for Taiwan (TW) on 6GHz
33797ae wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds support for the RTL8723BE PCIe Wi-Fi Adapter by adding backports drivers
Signed-off-by: David Adriao <davidadriao@dglitch.com>
[Do not remove rtl8xxxu and add dependency to rtl8723be-firmware]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It seems that somehow a wrong hash has been used for ipq-wifi, so refresh
it.
Fixes: f10d55df9e ("ipq-wifi: update to Git HEAD (2024-04-26)")
Signed-off-by: Robert Marko <robimarko@gmail.com>
fab9e29f6b92 ipq6018: update regdb in TPLink EAP610-Outdoor BDF
6d02b65fadf3 ipq8074: update RegDB in new submitted BDF
644ba9ea2e66 ipq6018: update RegDB in new submitted BDF
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Spectrum SAX1V1K is a AX WIFI router with 3 1G and 1 2.5G ports.
The router is provided to Spectrum customers.
It is OEM of Askey RT5010W
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923
It continues the original work by @MeisterLone to get this device supported.
Specifications:
```
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 2048MB of DDR3
• Storage: 1024MB eMMC
• Ethernet: 3x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
• 2.4GHz: Qualcomm QCN5024 4x4 802.11b/g/n/ax 1174 Mbps PHY rate
• 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• LED: 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x reset
• Power: 12V DC jack
```
Notes:
```
• This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
• Installation can be done by serial connection only.
• A poulated serial header is onboard
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923/6
• RX/TX is working, u-boot bootwait is active, secure boot is enabled.
```
Installation Instructions:
**Most part of the installation is performed from an initramfs image.**
Boot initramfs : Using serial connection
1. Boot up the device and wait till it displays "VERIFY_IB: Success. verify IB ok"
2. Once that message appears,
login with username 'root'
password serial number of your router in uppercase.
3. Use vi to paste the 'open.sh' script from @MeisterLone github on your device
https://github.com/MeisterLone/Askey-RT5010W-D187-REV6/blob/master/Patch/open.sh
4. chmod 755 open.sh
5. ./open.sh
6. Set your ip to 192.168.0.1
7. Run a TFTP server and host the initramfs image on the TFTP server and name it "recovery.img"
8. Reboot device. On boot it will try TFTP.
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Flash firmware: sysupgrade
# sysupgrade -n -v /tmp/openwrt_sysupgrade.bin
4. Set U-boot env variable: bootcmd
# fw_setenv bootcmd "run fix_uboot; run setup_and_boot"
5. Reboot the device
# reboot
6. Once device is booted, residue of previous firmware will prevent openwrt to work properly.
Factory Reset is MUST required
# Once serial console is displaying to login, hold reset button for 10 sec
7. Now everything should be operational.
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Connor Yoon <j_connor@taliaent.com>
With the switch to ZSTD for git clone packaging, hashes have changed so
fixup remaining package hashes that were missed in the inital update.
Fixes: b3c1c57 ("treewide: update PKG_MIRROR_HASH to zst")
Signed-off-by: Robert Marko <robimarko@gmail.com>
When using zst instead of xz, the hash changes. This commit fixes the
hash for packages and tools in core.
Signed-off-by: Paul Spooren <mail@aparcar.org>
It seems that somehow a wrong hash has slipped past PR CI again.
Fixes: 9ef4f7f919 ("qualcommax: ipq60xx: add yuncore fap650 support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The firmware blobs have all different licenses from the different
manufacturers of the binary blobs. This information is contained in the
upstream 'linux-firmware' repositroy.
This commit extends the package handling so that this information can be
added as an additional argument during packages generation.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
With the change in version schema the downloaded files changed, too,
mostly the hash is now prefixed with a tilde `~` instead of a dash `-`.
Since each downloaded archive contains folder with the same name as the
archive, the checksum changed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Alexander reported following:
iwlwifi 0000:00:14.3: Detected crf-id 0x3617, cnv-id 0x20000302 wfpm id 0x80000000
iwlwifi 0000:00:14.3: PCI dev a0f0/0074, rev=0x351, rfid=0x10a100
iwlwifi 0000:00:14.3: Direct firmware load for iwlwifi-QuZ-a0-hr-b0-77.ucode failed with error -2
It seems, that as of the current date, the highest firmware API version
supported by Linux 6.8-rc7 is still 77.
Closes: #14771
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Different from OPKG, APK uses a deterministic version schema which chips
the version into chunks and compares them individually. This enforces a
certain schema which was previously entirely flexible.
- Releases are added at the very and end prefixed with an `r` like
`1.2.3-r3`.
- Hashes are prefixed with a `~` like `1.2.3~abc123`.
- Dates become semantic versions, like `2024.04.01`
- Extra tags are possible like `_git`, `_alpha` and more.
For full details see the APK test list:
https://gitlab.alpinelinux.org/alpine/apk-tools/-/blob/master/test/version.data
Signed-off-by: Paul Spooren <mail@aparcar.org>
That new version seems to work more stable including mesh.
On version 2.4.0.1-01746 rproc was immediately crashing if mesh was
active.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
After a long time QCA has pushed an updated release of 2.9.0.1 firmware
for IPQ8074 and QCN9074, so lets update to 2.9.0.1-01977.
Sadly, still nothing new for IPQ6018.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Debian changelog:
intel-microcode (3.20240312.1) unstable; urgency=medium
* New upstream microcode datafile 20240312 (closes: #1066108)
- Mitigations for INTEL-SA-INTEL-SA-00972 (CVE-2023-39368):
Protection mechanism failure of bus lock regulator for some Intel
Processors may allow an unauthenticated user to potentially enable
denial of service via network access.
- Mitigations for INTEL-SA-INTEL-SA-00982 (CVE-2023-38575):
Non-transparent sharing of return predictor targets between contexts in
some Intel Processors may allow an authorized user to potentially
enable information disclosure via local access. Affects SGX as well.
- Mitigations for INTEL-SA-INTEL-SA-00898 (CVE-2023-28746), aka RFDS:
Information exposure through microarchitectural state after transient
execution from some register files for some Intel Atom Processors and
E-cores of Intel Core Processors may allow an authenticated user to
potentially enable information disclosure via local access. Enhances
VERW instruction to clear stale register buffers. Affects SGX as well.
Requires kernel update to be effective.
- Mitigations for INTEL-SA-INTEL-SA-00960 (CVE-2023-22655), aka TECRA:
Protection mechanism failure in some 3rd and 4th Generation Intel Xeon
Processors when using Intel SGX or Intel TDX may allow a privileged
user to potentially enable escalation of privilege via local access.
NOTE: effective only when loaded by firmware. Allows SMM firmware to
attack SGX/TDX.
- Mitigations for INTEL-SA-INTEL-SA-01045 (CVE-2023-43490):
Incorrect calculation in microcode keying mechanism for some Intel
Xeon D Processors with Intel SGX may allow a privileged user to
potentially enable information disclosure via local access.
* Fixes for other unspecified functional issues on many processors
* Updated microcodes:
sig 0x00050653, pf_mask 0x97, 2023-07-28, rev 0x1000191, size 36864
sig 0x00050656, pf_mask 0xbf, 2023-07-28, rev 0x4003605, size 38912
sig 0x00050657, pf_mask 0xbf, 2023-07-28, rev 0x5003605, size 37888
sig 0x0005065b, pf_mask 0xbf, 2023-08-03, rev 0x7002802, size 30720
sig 0x00050665, pf_mask 0x10, 2023-08-03, rev 0xe000015, size 23552
sig 0x000506f1, pf_mask 0x01, 2023-10-05, rev 0x003e, size 11264
sig 0x000606a6, pf_mask 0x87, 2023-09-14, rev 0xd0003d1, size 307200
sig 0x000606c1, pf_mask 0x10, 2023-12-05, rev 0x1000290, size 299008
sig 0x000706a1, pf_mask 0x01, 2023-08-25, rev 0x0040, size 76800
sig 0x000706a8, pf_mask 0x01, 2023-08-25, rev 0x0024, size 76800
sig 0x000706e5, pf_mask 0x80, 2023-09-14, rev 0x00c4, size 114688
sig 0x000806c1, pf_mask 0x80, 2023-09-13, rev 0x00b6, size 111616
sig 0x000806c2, pf_mask 0xc2, 2023-09-13, rev 0x0036, size 98304
sig 0x000806d1, pf_mask 0xc2, 2023-09-13, rev 0x0050, size 104448
sig 0x000806ec, pf_mask 0x94, 2023-07-16, rev 0x00fa, size 106496
sig 0x000806f8, pf_mask 0x87, 2024-01-03, rev 0x2b000590, size 579584
sig 0x000806f7, pf_mask 0x87, 2024-01-03, rev 0x2b000590
sig 0x000806f6, pf_mask 0x87, 2024-01-03, rev 0x2b000590
sig 0x000806f5, pf_mask 0x87, 2024-01-03, rev 0x2b000590
sig 0x000806f4, pf_mask 0x87, 2024-01-03, rev 0x2b000590
sig 0x00090661, pf_mask 0x01, 2023-09-26, rev 0x0019, size 20480
sig 0x00090672, pf_mask 0x07, 2023-09-19, rev 0x0034, size 224256
sig 0x00090675, pf_mask 0x07, 2023-09-19, rev 0x0034
sig 0x000b06f2, pf_mask 0x07, 2023-09-19, rev 0x0034
sig 0x000b06f5, pf_mask 0x07, 2023-09-19, rev 0x0034
sig 0x000906a3, pf_mask 0x80, 2023-09-19, rev 0x0432, size 222208
sig 0x000906a4, pf_mask 0x80, 2023-09-19, rev 0x0432
sig 0x000906c0, pf_mask 0x01, 2023-09-26, rev 0x24000026, size 20480
sig 0x000906e9, pf_mask 0x2a, 2023-09-28, rev 0x00f8, size 108544
sig 0x000906ea, pf_mask 0x22, 2023-07-26, rev 0x00f6, size 105472
sig 0x000906ec, pf_mask 0x22, 2023-07-26, rev 0x00f6, size 106496
sig 0x000906ed, pf_mask 0x22, 2023-07-27, rev 0x00fc, size 106496
sig 0x000a0652, pf_mask 0x20, 2023-07-16, rev 0x00fa, size 97280
sig 0x000a0653, pf_mask 0x22, 2023-07-16, rev 0x00fa, size 97280
sig 0x000a0655, pf_mask 0x22, 2023-07-16, rev 0x00fa, size 97280
sig 0x000a0660, pf_mask 0x80, 2023-07-16, rev 0x00fa, size 97280
sig 0x000a0661, pf_mask 0x80, 2023-07-16, rev 0x00fa, size 96256
sig 0x000a0671, pf_mask 0x02, 2023-09-14, rev 0x005e, size 108544
sig 0x000b0671, pf_mask 0x32, 2023-12-14, rev 0x0122, size 215040
sig 0x000b06a2, pf_mask 0xe0, 2023-12-07, rev 0x4121, size 220160
sig 0x000b06a3, pf_mask 0xe0, 2023-12-07, rev 0x4121
sig 0x000b06e0, pf_mask 0x11, 2023-09-25, rev 0x0015, size 138240
* New microcodes:
sig 0x000a06a4, pf_mask 0xe6, 2024-01-03, rev 0x001c, size 136192
sig 0x000b06a8, pf_mask 0xe0, 2023-12-07, rev 0x4121, size 220160
sig 0x000c06f2, pf_mask 0x87, 2023-11-20, rev 0x21000200, size 549888
sig 0x000c06f1, pf_mask 0x87, 2023-11-20, rev 0x21000200
* source: update symlinks to reflect id of the latest release, 20240312
* changelog, debian/changelog: fix typos
-- Henrique de Moraes Holschuh <hmh@debian.org> Tue, 12 Mar 2024 20:28:17 -0300
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Realtek RTL8188F is an 802.11n 1x1 USB Wi-Fi adapter. It has been
supported by the upstream rtl8xxxu driver since Linux 6.2 kernel.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
