This target adds support for the Allwinner D1 RISC-V based SoCs.
- RISC-V single-core T-Head C906 (RV64GCV)
- Tensilica HiFi4 DSP
- DDR2/DDR3 support
- 10/100/1000M ethernet
- usual peripherals like USB2, SPI, I2C, PWM, etc.
Four boards are supported:
- Dongshan Nezha STU
- 512Mb RAM
- ethernet
- LicheePi RV Dock
- 512Mb RAM
- wireless-only (RTL8723DS)
- MangoPi MQ-Pro
- 512Mb RAM
- there are pads available for an SPI flash
- wireless-only (RTL8723DS)
- Nezha D1
- 512Mb/1Gb/2Gb RAM
- 256Mb NAND flash
- ethernet, wireless
Installation:
Standard SD-card installation via dd-ing the generated image to
an SD-card of at least 256Mb.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add u-boot bootloader based on 2023.01 to support D1-based boards, currently:
- Dongshan Nezha STU
- LicheePi RV Dock
- MangoPi MQ-Pro
- Nezha D1
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
U-boot on D1 also uses OpenSBI as its payload. As the current version of
OpenSBI already supports D1 with no further patches required, allow
building it on the upcoming TARGET_d1 too.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Disabled services should be kept disabled after sysupgrade. This can be
easily handled using a proper uci-defaults script.
Extend sysupgrade to check for disabled services, generate uci-defaults
script disabling them and include it in backup.
Cc: Christian Marangi <ansuelsmth@gmail.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Replace mount + overlay with manually built tar archive that gets
prepended to the actual config files backup. This allows more
flexibility with including extra backup files. They can be included at
any paths and don't require writing to flash or mounting an overlay
which has its own limitations (mount points).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jo-Philipp Wich <jo@mein.io>
This allows building uncompressed tar archives from shell scripts (and
compressing them later if needed)
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
[rmilecki: adapt to sysupgrade needs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The boot loader does not have a fixed size limit for the kernel,
so we're free to change the layout. This may break sysupgrade, but a fresh
flash from initramfs works.
Fixes: 6e2962d4c5 ("mediatek: mt7622: skip build for MT7622 rfb1 (UBI)")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It should be "BananaPi BPi-R3 Mini" instead of just "BananaPi BPi-R3".
Fixes: bc25519f98 ("uboot-mediatek: add builds for BananaPi BPi-R3 mini")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The Arcadyan VRV9510KWAC23 (trade name Livebox Next) is a Lantiq router distributed by some spanish ISPs
Hardware:
- SoC: Lantiq VRX200
- CPU: 2x MIPS 34Kc 500 MHz
- RAM: 256 MiB DDR2
- Flash: 128 MiB NAND
- Ethernet: Built-in Gigabit Ethernet switch, 5x 1GbE
- Wifi 2.4GHz: Broadcom BCM43222KFBG 802.11b/g/b MIMO 2T2R
- Wifi 5GHz: Broadcom BCM4360KMLG 802.11ac MIMO 3T3R
- USB: 2x USB 2.0
- DSL: Built-in VDSL/ADSL2+ XWAY VRX208
- LEDs: 8x
- Buttons: 4x
- Phone: Lantiq PEF 42068 V XWAY SLIC120
Install instructions:
Detailed instructions can be found on the wiki https://openwrt.org/toh/arcadyan/vrv9510kwac23
1. Boot into UART mode and upload the the https://raw.githubusercontent.com/danielhuici/arcadyan-vrv9510kwac23-utils/main/u-boot.asc file via serial console to boot into U-Boot.
2. Perform a backup of the NAND
3. Setup a TFTP server and serve the https://github.com/danielhuici/arcadyan-vrv9510kwac23-utils/raw/main/u-boot.ltq.lzo.nandspl. Replace the OEM bootloader with this one. Erase your NAND and write the image into it
4. Reboot the router
5. Serve the OpenWrt ramdisk image on your TFTP server and boot it via U-Boot
6. When OpenWrt boots, flash the SquashFS OpenWrt image using LuCi interface, so OpenWrt gets installed into the NAND
Signed-off-by: Daniel Huici <danielhuici@hotmail.com>
Drop the flow-hash of the skb when forwarding to the L2TP netdev.
This avoids the L2TP qdisc from using the flow-hash from the outer
packet, which is identical for every flow within the tunnel.
This does not affect every platform but is specific for the ethernet
driver. It depends on the platform including L4 information in the
flow-hash.
Signed-off-by: David Bauer <mail@david-bauer.net>
The following kernel module package was added to the build recipe for the
Turris Omnia: kmod-mt7915-firmware
This module enables support for the official Wi-Fi 6 upgrade kit sold by
CZ.NIC, which includes the AW7915-NP1 miniPCIE board based on Mediatek
MT7915AN, providing 5 GHz Wi-Fi 6 connectivity. With this commit we now
support the latest Turris Omnia Wi-Fi 6 Edition
Signed-off-by: Jan Jasper de Kroon <jajadekroon@gmail.com>
this patch separates libe2p from e2fsprogs package, like all other
provided libraries are their own packages. Also some development headers
were missing so I added those along with pkg-config files.
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
Because some still unresolved bugs in this driver, which sprout
occasional questions what this patch works around, point to the issue
which started this. Being here, fill headers required by git am.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reduce and split pcie controller memory ranges for en7523 SoC
in order to properly load a pcie card on the second port.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
After commit ad62247800 ("base-files: improve lib/upgrade/common.sh")
behavior of export_bootdevice has been made consistent in such way that
always the whole disk device is exported (as that was the case already
when matching via UUID) rather than the partition device.
Do the same for the device holding the fitblk backing partition.
Fixes: 5992f976b3 ("base-files: recognize bootdevice on devices using fitblk")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If selected on a per-board base, fitblk doesn't end up in initramfs
images which always only come with the subtarget's default packages.
Hence fitblk needs to be included as a default package of all
subtargets making use of fitblk instead of it being selected for
individual boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we got fitblk_get_bootdev in /lib/upgrade/common.sh we don't
need platform_get_bootdev in each of the subtargets any longer.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Boards using the fitblk driver need special treatment when it comes to
detecting the actual block device used to store the image used to boot
from. Transparently handle this in 'export_bootdevice' and provide new
'fitblk_get_bootdev' function to replace implementations in
/lib/upgrade/platform.sh.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When building the UBI NVMEM provider on 32-bit platforms a compiler
warning is triggered due to different sizeof(int).
Fix this by using integer types with well-defined size.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In official OpenWrt we use kmod-r8169 driver provided by upstream kernel
instead of kmod-r8168 driver from Realtek.
Fixes: afca1236f3 ("rockchip: add NanoPi R4S Enterprise Edition build")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The device booting successfully indicates that bootloader has been
updated. Set compat_version to 1.1 on new configs and bump
compat_version to 1.1 on first boot after a successful sysupgrade.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Without UBINIZE_OPTS it is possile to have error:
"ubi0 error: ubi_attach_mtd_dev: failed to atach mtd23, error -22"
This solve this problem.
Signed-off-by: Marcin Gajda <mgajda@o2.pl>
TP-Link Archer C5 v4 is a dual band router with 5 GbE ports
Advertised as AC1200 for its 867Mbps (2x2) 5GHz band
and 300 Mbps (2x2) 2.4GHz band.
Specs:
- SoC: MediaTek MT7620A
- Ethernet: 5x GbE ports (Realtek RTL8367S)
- Wireless 2.4GHz: MediaTek MT7620A
- Wireless 5GHz: MediaTek MT7612E
- RAM: 64MiB
- ROM: 8MiB (GD25Q64CSIG)
- 1 USB 2.0 port
- 2 Buttons (WPS and reset)
- 8 LEDs
Flash instructions:
Currently one has to install OpenWrt only via the serial console
1. Rename the factory.bin to to test.bin
2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin
3. connect your device to the LAN port
4. power up the router and press 4 on the console to stop the boot process.
5. enter the following commands on the router console
tftp 0x80060000 test.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[Update leds, add fast-read]
Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[Rebuilt version based on mt7620 tplink_archer.dtsi, support for external LNA, remove bad cell count info]
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
From driver point of view no differance between rtl8367b and rtl8367s
if it connected through EXT2 (rgmii only).
So this trivial patch add some identification and initialization only.
SGMII/HSGMII mode for EXT1 is not implemented for the sake of patch
clairity.
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
[Fix code format]
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[add flags to separate chip_num/chip_id detection; drop error print in
rtl8367b_init_regs, drop unnecessary info prints, code style fixes]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[rebase; use MII macros]
Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[code optimization]
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Set root=/dev/fit0 cmdline parameter as the kernel won't mount rootfs
otherwise after the change from the FIT partition parser to the fitblk
driver which replaces it.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel warns about comparision of different types without cast when
building the fitblk driver on 32-bit platforms.
Fix this by using `min_t(size_t, ...`.
Fixes: 8fc5457869 ("kernel: add pending fitblk uImage.FIT sub-image block driver")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the new fitblk driver on the BananaPi R2 as well as UniElec U7623.
Introduce boot device selection for fitblk's /chosen/rootdisk
handle, similar to how it is already done on MT7622, MT7986 and MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The default environment for the Linksys E8450 and Belkin RT3200 got
truncated by one line due to a broken patch. While the impact was
luckily only cosmetic, fix it so bootmenu title also shows U-Boot
version again.
Fixes: 6aec3c7b5b ("mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI build")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
**Netgear LBR20** is a router with two gigabit ethernets , three wifi radios and integrated LTE cat.18 modem.
SoC Type: Qualcomm IPQ4019
RAM: 512 MiB
Flash: 256 MiB , SLC NAND, 2 Gbit (Macronix MX30LF2G18AC)
Bootloader: U-Boot
Modem: LTE CAT.18 Quectel EG-18EA , Max. 1.2Gbps downlink / 150Mbps uplink
WiFi class AC2200:
- radio0 : 5G on QCA9888 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps , 80MHz - limited for low channels
- radio1: 2,4G on IPQ4019 ,WiFi4- 802.11b/g/n MIMO2x2 300Mbps 40Mhz
- radio2: 5G on IPQ4019 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps ,80Mhz - limited for high channels (from 100 up to 165) . Becouse of DFS remember to set country before turning on.
Ethernet: 2x1GbE (WAN/LAN1, LAN2)
LEDs: section power : green and red , section on top (orbi) drived by TLC59208F: red, green ,blue and white
USB ports: No
Buttons: 2 Reset and SYNC(WPS)
Power: 12 VDC, 2,5 A
Connector type: Barrel
OpenWRT Installation
1. Simplest way is just do upgrade from webpage with *factory.img
2. You can also do it with standard tool for Netgear's debricking - NMPRFlash
3. Most advanced way is to open device , connect to UART console and :
- Prepare OpenWrt initramfs image in TFTP server root (server IP 192.168.1.10)
- Connect serial console (115200,8n1) to UART connector
- Connect TFTP server to RJ-45 port
- Stop in u-Boot and run u-Boot command:
> setenv serverip 192.168.1.10
> set fdt_high 0x85000000
> tftpboot 0x83000000 openwrt-ipq40xx-generic-netgear_lbr20-initramfs-zImage.itb
> bootm 0x83000000
- Login via ssh
- upload or download *sysupgrade.bin ( like wget ... or scp transfer)
- Install image via "sysupgrade -n" (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-netgear_lbr20-squashfs-sysupgrade.bin”)
Back to Stock
- Download firmware from official Netgear's webpage , it will be *.img file after decompressing.
- Use NMRPFlash tool ( detailed insructions on project page https://github.com/jclehner/nmrpflash )
Open the case
- Unscrew nuts and remove washers from antenna's conectors.
- There are two Torx T10 screws under the label next to antenna conectors. You have to unglue this label from left and right corner to get it
- Two parts of shell covers will slide out from eachother , you have to unglue two small rubber pads and namplate sticker on bottom to do that.
- PCB is screwed with 4Pcs of Torx T10 screws
- Before lifting up PCB remove pigtiles for LTE antennas and release them from PCB and radiator (black and white wires)
- On other side of PCB ,in left bottom corner there is already soldered with 4 pins UART connector for console. Counting from left it is +3,3V , TX , RX ,GND (reffer to this picture: https://i.ibb.co/Pmrf9KB/20240116-103524.jpg )
BDF's files are in firmware_qca-wireless https://github.com/openwrt/firmware_qca-wireless/ and in parallel sent to ath10k@lists.infradead.org.
Signed-off-by: Marcin Gajda <mgajda@o2.pl>
Replace ARM bootloader patch with pending upstream version. The patch
got reviewed upstream and tested on a Netgear R7800.
This fix a problem with the ARM decompressor and permits to use
AUTO_ZRELADDR without having to hardcode PHYS_OFFSET as the bootloader
now correctly parse the memory modes in the appended DTB.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
